Since support for mxc91231 was introduced 2009 it only saw patches that
were part of (mxc or arm) global cleanups. The only supported machine
only had 4 devices (2x UART, sdhc, watchdog).
Cc: Dmitriy Taychenachev <dimichxp@gmail.com>
LAKML-Reference: 1302211482-17926-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Having the silicon revision to appear on the boot log is a useful information.
MX31, MX35 and MX51 already show the silicon revision on boot.
Add support for displaying such information for MX53 as well.
Tested on a mx53loco board, where it shows:
CPU identified as i.MX53, silicon rev 2.0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1301068367-18937-1-git-send-email-fabio.estevam@freescale.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This used to be done in .map_io which is supposed to only setup the memory
mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The efikamx board is using a gpio to reset the board so add support
for it
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Enhanced Periodic Interrupt Timer (EPIT) is found on newer
i.MX SoCs and can be used as an alternative system timer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Add basic clock support, cpu identification, I/O mapping, interrupt
controller, serial port and ethernet.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Freescale i.MX51 processor uses a new interrupt controller. Add
driver for TrustZone Interrupt Controller
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
The fref is needless on mx25 since the reference clock is fixed at 24MHz.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows us to have more mapping functions for more than one
i.MX architecture in the kernel. As this is the earliest board
specific hook we have, also use it to set the cpu type.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds clock support for i.MX35 SoCs. We do not support setting
of clock rates yet, but most interesting clock rates should be reported.
I couldn't test all clock rates and the datasheet contains some obvious
bugs, so expect some bugs in this code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We had hardcoded cpu_is_ macros for mxc architectures till now. As we
want to run the same kernel on i.MX31 and i.MX35 this patch adds cpu_is_
macros which expand to 0 or 1 if only one architecture is compiled in and
only check for the cpu type if more than one architecture is compiled
in.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on code from "Martin Fuzzey" <mfuzzey@gmail.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- rename mxc_clocks_init to architecture specific versions. This
allows us to have more than one architecture compiled in.
- call mxc_timer_init from clock initialisation instead from board
code
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
