If ucsi_init() fails for some reason (e.g. ucsi_register_port()
fails or general communication failure to the PPM), particularly at
any point after the GET_CAPABILITY command had been issued, this
results in unwinding the initialization and returning an error.
However the ucsi structure's ucsi_capability member retains its
current value, including likely a non-zero num_connectors.
And because ucsi_init() itself is done in a workqueue a UCSI
interface driver will be unaware that it failed and may think the
ucsi_register() call was completely successful. Later, if
ucsi_unregister() is called, due to this stale ucsi->cap value it
would try to access the items in the ucsi->connector array which
might not be in a proper state or not even allocated at all and
results in NULL or invalid pointer dereference.
Fix this by clearing the ucsi->cap value to 0 during the error
path of ucsi_init() in order to prevent a later ucsi_unregister()
from entering the connector cleanup loop.
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210609073535.5094-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a390bef7db ("usb: gadget: fsl_mxc_udc: Remove the driver")
dropped the ARCH_MXC dependency from USB_FSL_USB2, leaving it depending
solely on FSL_SOC.
FSL_SOC is powerpc only; it was briefly available on ARM in 2014 but was
removed by commit cfd074ad86 ("ARM: imx: temporarily remove
CONFIG_SOC_FSL from LS1021A"). Therefore the driver can no longer be
enabled on ARM platforms.
This appears to be a mistake as arm64's ARCH_LAYERSCAPE and arm32
SOC_LS1021A SoCs use this symbol. It's enabled in these defconfigs:
arch/arm/configs/imx_v6_v7_defconfig:CONFIG_USB_FSL_USB2=y
arch/arm/configs/multi_v7_defconfig:CONFIG_USB_FSL_USB2=y
arch/powerpc/configs/mgcoge_defconfig:CONFIG_USB_FSL_USB2=y
arch/powerpc/configs/mpc512x_defconfig:CONFIG_USB_FSL_USB2=y
To fix, expand the dependencies so USB_FSL_USB2 can be enabled on the
ARM platforms, and with COMPILE_TEST.
Fixes: a390bef7db ("usb: gadget: fsl_mxc_udc: Remove the driver")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210610034957.93376-1-joel@jms.id.au
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As LKP noticed the Sparse is not happy about strict type handling:
.../typec/tcpm/wcove.c:380:50: sparse: expected unsigned short [usertype] header
.../typec/tcpm/wcove.c:380:50: sparse: got restricted __le16 const [usertype] header
Fix this by switching to use pd_header_cnt_le() instead of pd_header_cnt()
in the affected code.
Fixes: ae8a2ca8a2 ("usb: typec: Group all TCPCI/TCPM code together")
Fixes: 3c4fb9f169 ("usb: typec: wcove: start using tcpm for USB PD support")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210609172202.83377-1-andriy.shevchenko@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Fixes: 517c4c44b3 ("usb: Add driver to allow any GPIO to be used for 7211 USB signals")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210605080914.2057758-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no validation of the index from dwc3_wIndex_to_dep() and we might
be referring a non-existing ep and trigger a NULL pointer exception. In
certain configurations we might use fewer eps and the index might wrongly
indicate a larger ep index than existing.
By adding this validation from the patch we can actually report a wrong
index back to the caller.
In our usecase we are using a composite device on an older kernel, but
upstream might use this fix also. Unfortunately, I cannot describe the
hardware for others to reproduce the issue as it is a proprietary
implementation.
[ 82.958261] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a4
[ 82.966891] Mem abort info:
[ 82.969663] ESR = 0x96000006
[ 82.972703] Exception class = DABT (current EL), IL = 32 bits
[ 82.978603] SET = 0, FnV = 0
[ 82.981642] EA = 0, S1PTW = 0
[ 82.984765] Data abort info:
[ 82.987631] ISV = 0, ISS = 0x00000006
[ 82.991449] CM = 0, WnR = 0
[ 82.994409] user pgtable: 4k pages, 39-bit VAs, pgdp = 00000000c6210ccc
[ 83.000999] [00000000000000a4] pgd=0000000053aa5003, pud=0000000053aa5003, pmd=0000000000000000
[ 83.009685] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[ 83.026433] Process irq/62-dwc3 (pid: 303, stack limit = 0x000000003985154c)
[ 83.033470] CPU: 0 PID: 303 Comm: irq/62-dwc3 Not tainted 4.19.124 #1
[ 83.044836] pstate: 60000085 (nZCv daIf -PAN -UAO)
[ 83.049628] pc : dwc3_ep0_handle_feature+0x414/0x43c
[ 83.054558] lr : dwc3_ep0_interrupt+0x3b4/0xc94
...
[ 83.141788] Call trace:
[ 83.144227] dwc3_ep0_handle_feature+0x414/0x43c
[ 83.148823] dwc3_ep0_interrupt+0x3b4/0xc94
[ 83.181546] ---[ end trace aac6b5267d84c32f ]---
Signed-off-by: Marian-Cristian Rotariu <marian.c.rotariu@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210608162650.58426-1-marian.c.rotariu@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when skb_clone() or skb_copy_expand() fail,
it should pull skb with lengh indicated by header,
or not it will read network data and check it as header.
Cc: <stable@vger.kernel.org>
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.com>
Link: https://lore.kernel.org/r/20210608233547.3767-1-linyyuan@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For ACPI devices we have a symmetric API to put them, so use it in the driver.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210607205007.71458-3-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource() can return an error, add missed check for it.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210607205007.71458-2-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210607205007.71458-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the VDM responses couldn't be sent successfully, it doesn't need to
finish the AMS until the retry count reaches the limit.
Fixes: 0908c5aca3 ("usb: typec: tcpm: AMS and Collision Avoidance")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210606081452.764032-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_assign_descriptors() is called with 5 parameters,
the last 4 of which are the usb_descriptor_header for:
full-speed (USB1.1 - 12Mbps [including USB1.0 low-speed @ 1.5Mbps),
high-speed (USB2.0 - 480Mbps),
super-speed (USB3.0 - 5Gbps),
super-speed-plus (USB3.1 - 10Gbps).
The differences between full/high/super-speed descriptors are usually
substantial (due to changes in the maximum usb block size from 64 to 512
to 1024 bytes and other differences in the specs), while the difference
between 5 and 10Gbps descriptors may be as little as nothing
(in many cases the same tuning is simply good enough).
However if a gadget driver calls usb_assign_descriptors() with
a NULL descriptor for super-speed-plus and is then used on a max 10gbps
configuration, the kernel will crash with a null pointer dereference,
when a 10gbps capable device port + cable + host port combination shows up.
(This wouldn't happen if the gadget max-speed was set to 5gbps, but
it of course defaults to the maximum, and there's no real reason to
artificially limit it)
The fix is to simply use the 5gbps descriptor as the 10gbps descriptor,
if a 10gbps descriptor wasn't provided.
Obviously this won't fix the problem if the 5gbps descriptor is also
NULL, but such cases can't be so trivially solved (and any such gadgets
are unlikely to be used with USB3 ports any way).
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210609024459.1126080-1-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids a null pointer dereference in
f_{ecm,eem,hid,loopback,printer,rndis,serial,sourcesink,subset,tcm}
by simply reusing the 5gbps config for 10gbps.
Fixes: eaef50c760 ("usb: gadget: Update usb_assign_descriptors for SuperSpeedPlus")
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Michael R Sweet <msweet@msweet.org>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Sudhakar Panneerselvam <sudhakar.panneerselvam@oracle.com>
Cc: Wei Ming Chen <jj251510319013@gmail.com>
Cc: Will McVicker <willmcvicker@google.com>
Cc: Zqiang <qiang.zhang@windriver.com>
Reviewed-By: Lorenzo Colitti <lorenzo@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210608044141.3898496-1-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI controller is required to enter D3hot rather than D3cold for AMD
s2idle on this hardware generation.
Otherwise, the 'Controller Not Ready' (CNR) bit is not being cleared by
host in resume and eventually this results in xhci resume failures during
the s2idle wakeup.
Link: https://lore.kernel.org/linux-usb/1612527609-7053-1-git-send-email-Prike.Liang@amd.com/
Suggested-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable <stable@vger.kernel.org> # 5.11+
Link: https://lore.kernel.org/r/20210527154534.8900-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reasoning for this change is that if we already had
a packet pending, then we also already had a pending timer,
and as such there is no need to reschedule it.
This also prevents packets getting delayed 60 ms worst case
under a tiny packet every 290us transmit load, by keeping the
timeout always relative to the first queued up packet.
(300us delay * 16KB max aggregation / 80 byte packet =~ 60 ms)
As such the first packet is now at most delayed by 300us.
Under low transmit load, this will simply result in us sending
a shorter aggregate, as originally intended.
This patch has the benefit of greatly reducing (by ~10 factor
with 1500 byte frames aggregated into 16 kiB) the number of
(potentially pretty costly) updates to the hrtimer.
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210608085438.813960-1-zenczykowski@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Giving support for isp1763 made a little revival to this driver, add
entry in the MAINTAINERS file with me as maintainer.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210607170054.220975-1-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmC9dVwACgkQSFkpgVDW
cbs+oAf/b4mVmJpYIMTBM5tU086YpsZ80StjH3MVx2Hx/F8bM2ewovOUxOWPAY2o
A6ROuLUlU/0TT8U3LL5PEbQDHhuPsf1n3erv6iz63a72uzOouLeHOBYFP+E6aM5z
1mkr2yHXpwFe+aHpstXvOgeR4ano0kzMkx/I3SPH6P8/pXiBSrpvTiBwnxqvZxbb
VQuP9VfEF5e8vXuDiMF1V5qjea/BYnvjt2Yj34An3JHte13oTNRdFM/6aQiIEvt2
r6g0nBJizmhIHwtNYq30KfgFsNjiC9+dPtOCOVyv80c+Qu+F71EwEyqZSrOVLunh
hfxC/U6H8vy73Zo3gJP3xrXE+xvztw==
=OpDk
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Two bug fixes for cdns3 and cdnsp
* tag 'usb-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdnsp: Fix deadlock issue in cdnsp_thread_irq_handler
usb: cdns3: Enable TDL_CHK only for OUT ep
Here's a fix for some pipe-direction mismatches in the quatech2 driver,
and a couple of new device ids for ftdi_sio and omninet (and a related
trivial cleanup).
All but the ftdi_sio commit have been in linux-next, and with no
reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYLtSqwAKCRALxc3C7H1l
CPj2AQDSM/GeQ658vxYKPIA+8ZDBWubaYhq8KAUDqxL7hBMevAEAkbFhjgtyQt4h
32lqF2YsahxCHckvLXSnxxj1cTJxGAk=
=NKr6
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.13-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Jonah writes:
USB-serial fixes for 5.13-rc5
Here's a fix for some pipe-direction mismatches in the quatech2 driver,
and a couple of new device ids for ftdi_sio and omninet (and a related
trivial cleanup).
All but the ftdi_sio commit have been in linux-next, and with no
reported issues.
* tag 'usb-serial-5.13-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add NovaTech OrionMX product ID
USB: serial: omninet: update driver description
USB: serial: omninet: add device id for Zyxel Omni 56K Plus
USB: serial: quatech2: fix control-request directions
Add PID for the NovaTech OrionMX so it can be automatically detected.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
During unbind, ffs_func_eps_disable() will be executed, resulting in
completion callbacks for any pending USB requests. When using AIO,
irrespective of the completion status, io_data work is queued to
io_completion_wq to evaluate and handle the completed requests. Since
work runs asynchronously to the unbind() routine, there can be a
scenario where the work runs after the USB gadget has been fully
removed, resulting in accessing of a resource which has been already
freed. (i.e. usb_ep_free_request() accessing the USB ep structure)
Explicitly drain the io_completion_wq, instead of relying on the
destroy_workqueue() (in ffs_data_put()) to make sure no pending
completion work items are running.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1621644261-1236-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the state_machine_timer, we should also cancel possible pending
send discover identity hrtimer when unregister tcpm port.
Fixes: c34e85fa69 ("usb: typec: tcpm: Send DISCOVER_IDENTITY from dedicated work")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1622627829-11070-3-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the state_machine_timer, we should also cancel possible pending
frs hrtimer when unregister tcpm port.
Fixes: 8dc4bd0736 ("usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1622627829-11070-2-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving Alert Message, if it is not unexpected but is
unsupported for some reason, the port should return Not_Supported
Message response.
Also, according to PD3.0 Spec 6.5.2.1.4 Event Flags Field, the
OTP/OVP/OCP flags in the Event Flags field in Status Message no longer
require Get_PPS_Status Message to clear them. Thus remove it when
receiving Status Message with those flags being set.
In addition, add the missing AMS operations for Status Message.
Fixes: 64f7c494a3 ("typec: tcpm: Add support for sink PPS related messages")
Fixes: 0908c5aca3 ("usb: typec: tcpm: AMS and Collision Avoidance")
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210531164928.2368606-1-kyletso@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When only PHY1 is used (for example on Odroid-HC4), the regmap init code
uses the usb2 ports when doesn't initialize the PHY1 regmap entry.
This fixes:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
...
pc : regmap_update_bits_base+0x40/0xa0
lr : dwc3_meson_g12a_usb2_init_phy+0x4c/0xf8
...
Call trace:
regmap_update_bits_base+0x40/0xa0
dwc3_meson_g12a_usb2_init_phy+0x4c/0xf8
dwc3_meson_g12a_usb2_init+0x7c/0xc8
dwc3_meson_g12a_usb_init+0x28/0x48
dwc3_meson_g12a_probe+0x298/0x540
platform_probe+0x70/0xe0
really_probe+0xf0/0x4d8
driver_probe_device+0xfc/0x168
...
Fixes: 013af227f5 ("usb: dwc3: meson-g12a: handle the phy and glue registers separately")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210601084830.260196-1-narmstrong@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an error occurs after a successful 'regulator_enable()' call,
'regulator_disable()' must be called.
Fix the error handling path of the probe accordingly.
The remove function doesn't need to be fixed, because the
'regulator_disable()' call is already hidden in 'dwc3_meson_g12a_suspend()'
which is called via 'pm_runtime_set_suspended()' in the remove function.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/79df054046224bbb0716a8c5c2082650290eec86.1621616013.git.christophe.jaillet@wanadoo.fr
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_ams_start is used to initiate an AMS as well as checking Collision
Avoidance conditions but not for flagging passive AMS (initiated by the
port partner). Fix the misuses of tcpm_ams_start in tcpm_pd_svdm.
ATTENTION doesn't need responses so the AMS flag is not needed here.
Fixes: 0bc3ee9288 ("usb: typec: tcpm: Properly interrupt VDM AMS")
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210601123151.3441914-5-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ID Header VDO and Product VDOs defined in USB PD Spec rev 2.0 and
rev 3.1 are quite different. Add an additional array snk_vdo_v1 and
send it as the response to the port partner if it only supports SVDM
version 1.0.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210601123151.3441914-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the VDO definition for USB PD rev 2.0 in the bindings and define a
new property snk-vdos-v1 containing legacy VDOs as the responses to the
port partner which only supports PD rev 2.0.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210601123151.3441914-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In USB PD Spec Rev 3.1 Ver 1.0, section "6.12.5 Applicability of
Structured VDM Commands", DFP is allowed and recommended to respond to
Discovery Identity with ACK. And in section "6.4.4.2.5.1 Commands other
than Attention", NAK should be returned only when receiving Messages
with invalid fields, Messages in wrong situation, or unrecognize
Messages.
Still keep the original design for SVDM Version 1.0 for backward
compatibilities.
Fixes: 193a68011f ("staging: typec: tcpm: Respond to Discover Identity commands")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210601123151.3441914-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BIT macro is not defined. Replace it with generic bit operations.
Fixes: 630dce2810 ("dt-bindings: connector: Add SVDM VDO properties")
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210527121029.583611-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3 DebugFS directory and files are currently created once
during probe. This includes creation of subdirectories for each
of the gadget's endpoints. This works fine for peripheral-only
controllers, as dwc3_core_init_mode() calls dwc3_gadget_init()
just prior to calling dwc3_debugfs_init().
However, for dual-role controllers, dwc3_core_init_mode() will
instead call dwc3_drd_init() which is problematic in a few ways.
First, the initial state must be determined, then dwc3_set_mode()
will have to schedule drd_work and by then dwc3_debugfs_init()
could have already been invoked. Even if the initial mode is
peripheral, dwc3_gadget_init() happens after the DebugFS files
are created, and worse so if the initial state is host and the
controller switches to peripheral much later. And secondly,
even if the gadget endpoints' debug entries were successfully
created, if the controller exits peripheral mode, its dwc3_eps
are freed so the debug files would now hold stale references.
So it is best if the DebugFS endpoint entries are created and
removed dynamically at the same time the underlying dwc3_eps are.
Do this by calling dwc3_debugfs_create_endpoint_dir() as each
endpoint is created, and conversely remove the DebugFS entry when
the endpoint is freed.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210529192932.22912-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current timer PD_T_SINK_WAIT_CAP is set to 240ms which will violate the
SinkWaitCapTimer (tTypeCSinkWaitCap 310 - 620 ms) defined in the PD
Spec if the port is faster enough when running the state machine. Set it
to the lower bound 310ms to ensure the timeout is in Spec.
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210528081613.730661-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 92af4fc6ec ("usb: musb: Fix suspend with devices
connected for a64"), the logic to support the
MUSB_QUIRK_B_DISCONNECT_99 quirk was modified to only conditionally
schedule the musb->irq_work delayed work.
This commit badly breaks ECM Gadget on AM335X. Indeed, with this
commit, one can observe massive packet loss:
$ ping 192.168.0.100
...
15 packets transmitted, 3 received, 80% packet loss, time 14316ms
Reverting this commit brings back a properly functioning ECM
Gadget. An analysis of the commit seems to indicate that a mistake was
made: the previous code was not falling through into the
MUSB_QUIRK_B_INVALID_VBUS_91, but now it is, unless the condition is
taken.
Changing the logic to be as it was before the problematic commit *and*
only conditionally scheduling musb->irq_work resolves the regression:
$ ping 192.168.0.100
...
64 packets transmitted, 64 received, 0% packet loss, time 64475ms
Fixes: 92af4fc6ec ("usb: musb: Fix suspend with devices connected for a64")
Cc: stable@vger.kernel.org
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Link: https://lore.kernel.org/r/20210528140446.278076-1-thomas.petazzoni@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There exists a possible scenario in which dwc3_gadget_init() can fail:
during during host -> peripheral mode switch in dwc3_set_mode(), and
a pending gadget driver fails to bind. Then, if the DRD undergoes
another mode switch from peripheral->host the resulting
dwc3_gadget_exit() will attempt to reference an invalid and dangling
dwc->gadget pointer as well as call dma_free_coherent() on unmapped
DMA pointers.
The exact scenario can be reproduced as follows:
- Start DWC3 in peripheral mode
- Configure ConfigFS gadget with FunctionFS instance (or use g_ffs)
- Run FunctionFS userspace application (open EPs, write descriptors, etc)
- Bind gadget driver to DWC3's UDC
- Switch DWC3 to host mode
=> dwc3_gadget_exit() is called. usb_del_gadget() will put the
ConfigFS driver instance on the gadget_driver_pending_list
- Stop FunctionFS application (closes the ep files)
- Switch DWC3 to peripheral mode
=> dwc3_gadget_init() fails as usb_add_gadget() calls
check_pending_gadget_drivers() and attempts to rebind the UDC
to the ConfigFS gadget but fails with -19 (-ENODEV) because the
FFS instance is not in FFS_ACTIVE state (userspace has not
re-opened and written the descriptors yet, i.e. desc_ready!=0).
- Switch DWC3 back to host mode
=> dwc3_gadget_exit() is called again, but this time dwc->gadget
is invalid.
Although it can be argued that userspace should take responsibility
for ensuring that the FunctionFS application be ready prior to
allowing the composite driver bind to the UDC, failure to do so
should not result in a panic from the kernel driver.
Fix this by setting dwc->gadget to NULL in the failure path of
dwc3_gadget_init() and add a check to dwc3_gadget_exit() to bail out
unless the gadget pointer is valid.
Fixes: e81a7018d9 ("usb: dwc3: allocate gadget structure dynamically")
Cc: <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210528160405.17550-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current sequence utilizes dwc3_gadget_disable_irq() alongside
synchronize_irq() to ensure that no further DWC3 events are generated.
However, the dwc3_gadget_disable_irq() API only disables device
specific events. Endpoint events can still be generated. Briefly
disable the interrupt line, so that the cleanup code can run to
prevent device and endpoint events. (i.e. __dwc3_gadget_stop() and
dwc3_stop_active_transfers() respectively)
Without doing so, it can lead to both the interrupt handler and the
pullup disable routine both writing to the GEVNTCOUNT register, which
will cause an incorrect count being read from future interrupts.
Fixes: ae7e86108b ("usb: dwc3: Stop active transfers before halting the controller")
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1621571037-1424-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull i2c fixes from Wolfram Sang:
"This is a bit larger than usual at rc4 time. The reason is due to
Lee's work of fixing newly reported build warnings.
The rest is fixes as usual"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (22 commits)
MAINTAINERS: adjust to removing i2c designware platform data
i2c: s3c2410: fix possible NULL pointer deref on read message after write
i2c: mediatek: Disable i2c start_en and clear intr_stat brfore reset
i2c: i801: Don't generate an interrupt on bus reset
i2c: mpc: implement erratum A-004447 workaround
powerpc/fsl: set fsl,i2c-erratum-a004447 flag for P1010 i2c controllers
powerpc/fsl: set fsl,i2c-erratum-a004447 flag for P2041 i2c controllers
dt-bindings: i2c: mpc: Add fsl,i2c-erratum-a004447 flag
i2c: busses: i2c-stm32f4: Remove incorrectly placed ' ' from function name
i2c: busses: i2c-st: Fix copy/paste function misnaming issues
i2c: busses: i2c-pnx: Provide descriptions for 'alg_data' data structure
i2c: busses: i2c-ocores: Place the expected function names into the documentation headers
i2c: busses: i2c-eg20t: Fix 'bad line' issue and provide description for 'msgs' param
i2c: busses: i2c-designware-master: Fix misnaming of 'i2c_dw_init_master()'
i2c: busses: i2c-cadence: Fix incorrectly documented 'enum cdns_i2c_slave_mode'
i2c: busses: i2c-ali1563: File headers are not good candidates for kernel-doc
i2c: muxes: i2c-arb-gpio-challenge: Demote non-conformant kernel-doc headers
i2c: busses: i2c-nomadik: Fix formatting issue pertaining to 'timeout'
i2c: sh_mobile: Use new clock calculation formulas for RZ/G2E
i2c: I2C_HISI should depend on ACPI
...
- Fix addfd notification race condition (Sargun Dhillon)
-----BEGIN PGP SIGNATURE-----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=c9Hd
-----END PGP SIGNATURE-----
Merge tag 'seccomp-fixes-v5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp fixes from Kees Cook:
"This fixes a hard-to-hit race condition in the addfd user_notif
feature of seccomp, visible since v5.9.
And a small documentation fix"
* tag 'seccomp-fixes-v5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
seccomp: Refactor notification handler to prepare for new semantics
Documentation: seccomp: Fix user notification documentation
I have a handful of RISC-V related fixes:
* A fix to avoid errors when the stack tracing code is tracing itself.
* A fix to resurrect the memtest= kernel command line argument on
RISC-V, which was briefly enabled during the merge window before a
refactoring disabled it.
* A build fix and some warning cleanups.
-----BEGIN PGP SIGNATURE-----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=Pg04
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"A handful of RISC-V related fixes:
- avoid errors when the stack tracing code is tracing itself.
- resurrect the memtest= kernel command line argument on RISC-V,
which was briefly enabled during the merge window before a
refactoring disabled it.
- build fix and some warning cleanups"
* tag 'riscv-for-linus-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: kexec: Fix W=1 build warnings
riscv: kprobes: Fix build error when MMU=n
riscv: Select ARCH_USE_MEMTEST
riscv: stacktrace: fix the riscv stacktrace when CONFIG_FRAME_POINTER enabled
- Fix a bug where unmapping operations end earlier than expected, which
can cause chaos on multi-block directory and symlink shrink
operations.
- Fix an erroneous assert that can trigger if we try to transition a
bmap structure from btree format to extents format with zero extents.
This was exposed by xfs/538.
-----BEGIN PGP SIGNATURE-----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=y7+K
-----END PGP SIGNATURE-----
Merge tag 'xfs-5.13-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"This week's pile mitigates some decades-old problems in how extent
size hints interact with realtime volumes, fixes some failures in
online shrink, and fixes a problem where directory and symlink
shrinking on extremely fragmented filesystems could fail.
The most user-notable change here is to point users at our (new) IRC
channel on OFTC. Freedom isn't free, it costs folks like you and me;
and if you don't kowtow, they'll expel everyone and take over your
channel. (Ok, ok, that didn't fit the song lyrics...)
Summary:
- Fix a bug where unmapping operations end earlier than expected,
which can cause chaos on multi-block directory and symlink shrink
operations.
- Fix an erroneous assert that can trigger if we try to transition a
bmap structure from btree format to extents format with zero
extents. This was exposed by xfs/538"
* tag 'xfs-5.13-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: bunmapi has unnecessary AG lock ordering issues
xfs: btree format inode forks can have zero extents
xfs: add new IRC channel to MAINTAINERS
xfs: validate extsz hints against rt extent size when rtinherit is set
xfs: standardize extent size hint validation
xfs: check free AG space when making per-AG reservations
This refactors the user notification code to have a do / while loop around
the completion condition. This has a small change in semantic, in that
previously we ignored addfd calls upon wakeup if the notification had been
responded to, but instead with the new change we check for an outstanding
addfd calls prior to returning to userspace.
Rodrigo Campos also identified a bug that can result in addfd causing
an early return, when the supervisor didn't actually handle the
syscall [1].
[1]: https://lore.kernel.org/lkml/20210413160151.3301-1-rodrigo@kinvolk.io/
Fixes: 7cf97b1254 ("seccomp: Introduce addfd ioctl to seccomp user notifier")
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Acked-by: Tycho Andersen <tycho@tycho.pizza>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Rodrigo Campos <rodrigo@kinvolk.io>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210517193908.3113-3-sargun@sargun.me
Here are some tiny char/misc driver fixes for 5.13-rc4.
Nothing huge here, just some tiny fixes for reported issues:
- 2 interconnect driver fixes
- kgdb build warning fix for gcc-11
- hgafb regression fix
- soundwire driver fix
- mei driver fix
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYLJIxQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykGCgCfX/NsOhFfGDwuLB1cdvCbz7yAy0wAn2RkpPEd
rvLlnmp4+mAxDXmBsAqP
=cgtc
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some tiny char/misc driver fixes for 5.13-rc4.
Nothing huge here, just some tiny fixes for reported issues:
- two interconnect driver fixes
- kgdb build warning fix for gcc-11
- hgafb regression fix
- soundwire driver fix
- mei driver fix
All have been in linux-next with no reported issues"
* tag 'char-misc-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: request autosuspend after sending rx flow control
kgdb: fix gcc-11 warnings harder
video: hgafb: correctly handle card detect failure during probe
soundwire: qcom: fix handling of qcom,ports-block-pack-mode
interconnect: qcom: Add missing MODULE_DEVICE_TABLE
interconnect: qcom: bcm-voter: add a missing of_node_put()
Here are 3 small driver core / debugfs fixes for 5.13-rc4:
- debugfs fix for incorrect "lockdown" mode for selinux accesses
- 2 device link changes, one bugfix and one cleanup
All of these have been in linux-next for over a week with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYLJMrQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynf8ACgvsZCX7Wi3GYtFovfomHsCRKpZBsAn0sqfSAL
TXHePEnj2tJ5c22TSqSt
=Zx6Z
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are three small driver core / debugfs fixes for 5.13-rc4:
- debugfs fix for incorrect "lockdown" mode for selinux accesses
- two device link changes, one bugfix and one cleanup
All of these have been in linux-next for over a week with no reported
problems"
* tag 'driver-core-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers: base: Reduce device link removal code duplication
drivers: base: Fix device link removal
debugfs: fix security_locked_down() call for SELinux
Here are some small IIO and staging driver fixes for reported issues for
5.13-rc4.
Nothing major here, tiny changes for reported problems, full details are
in the shortlog if people are curious.
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYLJNPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynsWgCggwpoOPGXwjV0qBf135hoAPUT6p8AoJOtfIuq
2VJMflDGHTd/B4p3iGsx
=1P6T
-----END PGP SIGNATURE-----
Merge tag 'staging-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some small IIO and staging driver fixes for reported issues
for 5.13-rc4.
Nothing major here, tiny changes for reported problems, full details
are in the shortlog if people are curious.
All have been in linux-next for a while with no reported problems"
* tag 'staging-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: adc: ad7793: Add missing error code in ad7793_setup()
iio: adc: ad7923: Fix undersized rx buffer.
iio: adc: ad7768-1: Fix too small buffer passed to iio_push_to_buffers_with_timestamp()
iio: dac: ad5770r: Put fwnode in error case during ->probe()
iio: gyro: fxas21002c: balance runtime power in error path
staging: emxx_udc: fix loop in _nbu2ss_nuke()
staging: iio: cdc: ad7746: avoid overwrite of num_channels
iio: adc: ad7192: handle regulator voltage error first
iio: adc: ad7192: Avoid disabling a clock that was never enabled.
iio: adc: ad7124: Fix potential overflow due to non sequential channel numbers
iio: adc: ad7124: Fix missbalanced regulator enable / disable on error.
Here are some small fixes for reported problems for tty and serial
drivers for 5.13-rc4.
They consist of:
- 8250 bugfixes and new device support
- lockdown security mode fixup
- syzbot found problems fixed
- 8250_omap fix for interrupt storm
- revert of 8250_omap driver fix as it caused worse problem than
the original issue
All but the last patch have been in linux-next for a while, the last one
is a revert of a problem found in linux-next with the 8250_omap driver
change.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYLJODQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yna7gCgmKIssymva29JpQb54HuzRooD8jcAn3XeMVWI
E4TQzaTFC1mNAQy8GU4F
=cLjq
-----END PGP SIGNATURE-----
Merge tag 'tty-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver fixes from Greg KH:
"Here are some small fixes for reported problems for tty and serial
drivers for 5.13-rc4.
They consist of:
- 8250 bugfixes and new device support
- lockdown security mode fixup
- syzbot found problems fixed
- 8250_omap fix for interrupt storm
- revert of 8250_omap driver fix as it caused worse problem than the
original issue
All but the last patch have been in linux-next for a while, the last
one is a revert of a problem found in linux-next with the 8250_omap
driver change"
* tag 'tty-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250: 8250_omap: Fix possible interrupt storm"
serial: 8250_pci: handle FL_NOIRQ board flag
serial: rp2: use 'request_firmware' instead of 'request_firmware_nowait'
serial: 8250_pci: Add support for new HPE serial device
serial: 8250: 8250_omap: Fix possible interrupt storm
serial: 8250: Use BIT(x) for UART_{CAP,BUG}_*
serial: 8250: Add UART_BUG_TXRACE workaround for Aspeed VUART
serial: 8250_dw: Add device HID for new AMD UART controller
serial: sh-sci: Fix off-by-one error in FIFO threshold register setting
serial: core: fix suspicious security_locked_down() call
serial: tegra: Fix a mask operation that is always true
Here are a number of tiny USB and Thunderbolt driver fixes for 5.13-rc4.
They consist of:
- thunderbolt fixes for some NVM bound issues
- xhci fixes for reported problems
- control-request fixups
- documentation build warning fixes
- new usb-serial driver device ids
- typec bugfixes for reported issues
- usbfs warning fixups (could be triggered from userspace)
- other tiny fixes for reported problems.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYLJOvA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoGACg1Fu7eGouMBaHMykdR04lHgixb20An2Pna0fu
MPOqJSrKIF4/D6rUcsep
=wA32
-----END PGP SIGNATURE-----
Merge tag 'usb-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt fixes from Greg KH:
"Here are a number of tiny USB and Thunderbolt driver fixes for
5.13-rc4.
They consist of:
- thunderbolt fixes for some NVM bound issues
- xhci fixes for reported problems
- control-request fixups
- documentation build warning fixes
- new usb-serial driver device ids
- typec bugfixes for reported issues
- usbfs warning fixups (could be triggered from userspace)
- other tiny fixes for reported problems.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
xhci: Fix 5.12 regression of missing xHC cache clearing command after a Stall
xhci: fix giving back URB with incorrect status regression in 5.12
usb: gadget: udc: renesas_usb3: Fix a race in usb3_start_pipen()
usb: typec: tcpm: Respond Not_Supported if no snk_vdo
usb: typec: tcpm: Properly interrupt VDM AMS
USB: trancevibrator: fix control-request direction
usb: Restore the usb_header label
usb: typec: tcpm: Use LE to CPU conversion when accessing msg->header
usb: typec: ucsi: Clear pending after acking connector change
usb: typec: mux: Fix matching with typec_altmode_desc
misc/uss720: fix memory leak in uss720_probe
usb: dwc3: gadget: Properly track pending and queued SG
USB: usbfs: Don't WARN about excessively large memory allocations
thunderbolt: usb4: Fix NVM read buffer bounds and offset issue
thunderbolt: dma_port: Fix NVM read buffer bounds and offset issue
usb: chipidea: udc: assign interrupt number to USB gadget structure
usb: cdnsp: Fix lack of removing request from pending list.
usb: cdns3: Fix runtime PM imbalance on error
USB: serial: pl2303: add device id for ADLINK ND-6530 GC
USB: serial: ti_usb_3410_5052: add startech.com device id
...
* Another state update on exit to userspace fix
* Prevent the creation of mixed 32/64 VMs
* Fix regression with irqbypass not restarting the guest on failed connect
* Fix regression with debug register decoding resulting in overlapping access
* Commit exception state on exit to usrspace
* Fix the MMU notifier return values
* Add missing 'static' qualifiers in the new host stage-2 code
x86 fixes:
* fix guest missed wakeup with assigned devices
* fix WARN reported by syzkaller
* do not use BIT() in UAPI headers
* make the kvm_amd.avic parameter bool
PPC fixes:
* make halt polling heuristics consistent with other architectures
selftests:
* various fixes
* new performance selftest memslot_perf_test
* test UFFD minor faults in demand_paging_test
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmCyF0MUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOHSgf/Q4Hm5e12Bj2xJy6A+iShnrbbT8PW
hcIIOA7zGWXfjVYcBV7anbj7CcpzfIz0otcRBABa5mkhj+fb3YmPEb0EzCPi4Hru
zxpcpB2w7W7WtUOIKe2EmaT+4Pk6/iLcfr8UMHMqx460akE9OmIg10QNWai3My/3
RIOeakSckBI9e/1TQZbxH66dsLwCT0lLco7i7AWHdFxkzUQyoA34HX5pczOCBsO5
3nXH+/txnRVhqlcyzWLVVGVzFqmpHtBqkIInDOXfUqIoxo/gOhOgF1QdMUEKomxn
5ZFXlL5IXNtr+7yiI67iHX7CWkGZE9oJ04TgPHn6LR6wRnVvc3JInzcB5Q==
=ollO
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM fixes:
- Another state update on exit to userspace fix
- Prevent the creation of mixed 32/64 VMs
- Fix regression with irqbypass not restarting the guest on failed
connect
- Fix regression with debug register decoding resulting in
overlapping access
- Commit exception state on exit to usrspace
- Fix the MMU notifier return values
- Add missing 'static' qualifiers in the new host stage-2 code
x86 fixes:
- fix guest missed wakeup with assigned devices
- fix WARN reported by syzkaller
- do not use BIT() in UAPI headers
- make the kvm_amd.avic parameter bool
PPC fixes:
- make halt polling heuristics consistent with other architectures
selftests:
- various fixes
- new performance selftest memslot_perf_test
- test UFFD minor faults in demand_paging_test"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (44 commits)
selftests: kvm: fix overlapping addresses in memslot_perf_test
KVM: X86: Kill off ctxt->ud
KVM: X86: Fix warning caused by stale emulation context
KVM: X86: Use kvm_get_linear_rip() in single-step and #DB/#BP interception
KVM: x86/mmu: Fix comment mentioning skip_4k
KVM: VMX: update vcpu posted-interrupt descriptor when assigning device
KVM: rename KVM_REQ_PENDING_TIMER to KVM_REQ_UNBLOCK
KVM: x86: add start_assignment hook to kvm_x86_ops
KVM: LAPIC: Narrow the timer latency between wait_lapic_expire and world switch
selftests: kvm: do only 1 memslot_perf_test run by default
KVM: X86: Use _BITUL() macro in UAPI headers
KVM: selftests: add shared hugetlbfs backing source type
KVM: selftests: allow using UFFD minor faults for demand paging
KVM: selftests: create alias mappings when using shared memory
KVM: selftests: add shmem backing source type
KVM: selftests: refactor vm_mem_backing_src_type flags
KVM: selftests: allow different backing source types
KVM: selftests: compute correct demand paging size
KVM: selftests: simplify setup_demand_paging error handling
KVM: selftests: Print a message if /dev/kvm is missing
...
