It looks like the following patch can make FQ very precise, even in VM
or stressed hosts. It matters at high pacing rates.
We take into account the difference between the time that was programmed
when last packet was sent, and current time (a drift of tens of usecs is
often observed)
Add an EWMA of the unthrottle latency to help diagnostics.
This latency is the difference between current time and oldest packet in
delayed RB-tree. This accounts for the high resolution timer latency,
but can be different under stress, as fq_check_throttled() can be
opportunistically be called from a dequeue() called after an enqueue()
for a different flow.
Tested:
// Start a 10Gbit flow
$ netperf --google-pacing-rate 1250000000 -H lpaa24 -l 10000 -- -K bbr &
Before patch :
$ sar -n DEV 10 5 | grep eth0 | grep Average
Average: eth0 17106.04 756876.84 1102.75 1119049.02 0.00 0.00 0.52
After patch :
$ sar -n DEV 10 5 | grep eth0 | grep Average
Average: eth0 17867.00 800245.90 1151.77 1183172.12 0.00 0.00 0.52
A new iproute2 tc can output the 'unthrottle latency' :
$ tc -s qd sh dev eth0 | grep latency
0 gc, 0 highprio, 32490767 throttled, 2382 ns latency
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_acked() is using 32bit arithmetics on 16bits vars, via TSN_lte()
macros, which is weird and confusing.
Once the offset to ctsn is calculated, all wrapping is already handled
and thus to verify the Gap Ack blocks we can just use pure
less/big-or-equal than checks.
Also, rename gap variable to tsn_offset, so it's more meaningful, as
it doesn't point to any gap at all.
Even so, I don't think this discrepancy resulted in any practical bug.
This patch is a preparation for the next one, which will introduce
typecheck() for TSN_lte() macros and would cause a compile error here.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Reported-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On error path in route4_change(), 'f' could be NULL,
so we should check NULL before calling tcf_exts_destroy().
Fixes: b9a24bb76b ("net_sched: properly handle failure case of tcf_exts_init()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already checked for !found just a bit before:
if (!found) {
regs->verdict.code = NFT_BREAK;
return;
}
if (found && set->flags & NFT_SET_MAP)
^^^^^
So this redundant check can just go away.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It's better to use sizeof(info->name)-1 as index to force set the string
tail instead of literal number '29'.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There are some codes which are used to get one random once in netfilter.
We could use net_get_random_once to simplify these codes.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
pkt->xt.thoff is not always set properly, but we use it without any check.
For payload expr, it will cause wrong results. For nftrace, we may notify
the wrong network or transport header to the user space, furthermore,
input the following nft rules, warning message will be printed out:
# nft add rule arp filter output meta nftrace set 1
WARNING: CPU: 0 PID: 13428 at net/netfilter/nf_tables_trace.c:263
nft_trace_notify+0x4a3/0x5e0 [nf_tables]
Call Trace:
[<ffffffff813d58ae>] dump_stack+0x63/0x85
[<ffffffff810a4c0b>] __warn+0xcb/0xf0
[<ffffffff810a4d3d>] warn_slowpath_null+0x1d/0x20
[<ffffffffa0589703>] nft_trace_notify+0x4a3/0x5e0 [nf_tables]
[ ... ]
[<ffffffffa05690a8>] nft_do_chain_arp+0x78/0x90 [nf_tables_arp]
[<ffffffff816f4aa2>] nf_iterate+0x62/0x80
[<ffffffff816f4b33>] nf_hook_slow+0x73/0xd0
[<ffffffff81732bbf>] arp_xmit+0x8f/0xb0
[ ... ]
[<ffffffff81732d36>] arp_solicit+0x106/0x2c0
So before we use pkt->xt.thoff, check the tprot_set first.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There's an off-by-one issue in nft_payload_fast_eval, skb_tail_pointer
and ptr + priv->len all point to the last valid address plus 1. So if
they are equal, we can still fetch the valid data. It's unnecessary to
fall back to nft_payload_eval.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, the user can specify the queue numbers by _QUEUE_NUM and
_QUEUE_TOTAL attributes, this is enough in most situations.
But acctually, it is not very flexible, for example:
tcp dport 80 mapped to queue0
tcp dport 81 mapped to queue1
tcp dport 82 mapped to queue2
In order to do this thing, we must add 3 nft rules, and more
mapping meant more rules ...
So take one register to select the queue number, then we can add one
simple rule to mapping queues, maybe like this:
queue num tcp dport map { 80:0, 81:1, 82:2 ... }
Florian Westphal also proposed wider usage scenarios:
queue num jhash ip saddr . ip daddr mod ...
queue num meta cpu ...
queue num meta mark ...
The last point is how to load a queue number from sreg, although we can
use *(u16*)®s->data[reg] to load the queue number, just like nat expr
to load its l4port do.
But we will cooperate with hash expr, meta cpu, meta mark expr and so on.
They all store the result to u32 type, so cast it to u16 pointer and
dereference it will generate wrong result in the big endian system.
So just keep it simple, we treat queue number as u32 type, although u16
type is already enough.
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fetch value and validate u32 netlink attribute. This validation is
usually required when the u32 netlink attributes are being stored in a
field whose size is smaller.
This patch revisits 4da449ae1d ("netfilter: nft_exthdr: Add size check
on u8 nft_exthdr attributes").
Fixes: 96518518cc ("netfilter: add nftables")
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
"Mostly small bits scattered all over the place, which is usually how
things go this late in the -rc series.
1) Proper driver init device resets in bnx2, from Baoquan He.
2) Fix accounting overflow in __tcp_retransmit_skb(),
sk_forward_alloc, and ip_idents_reserve, from Eric Dumazet.
3) Fix crash in bna driver ethtool stats handling, from Ivan Vecera.
4) Missing check of skb_linearize() return value in mac80211, from
Johannes Berg.
5) Endianness fix in nf_table_trace dumps, from Liping Zhang.
6) SSN comparison fix in SCTP, from Marcelo Ricardo Leitner.
7) Update DSA and b44 MAINTAINERS entries.
8) Make input path of vti6 driver work again, from Nicolas Dichtel.
9) Off-by-one in mlx4, from Sebastian Ott.
10) Fix fallback route lookup handling in ipv6, from Vincent Bernat.
11) Fix stack corruption on probe in qed driver, from Yuval Mintz.
12) PHY init fixes in r8152 from Hayes Wang.
13) Missing SKB free in irda_accept error path, from Phil Turnbull"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tcp: properly account Fast Open SYN-ACK retrans
tcp: fix under-accounting retransmit SNMP counters
MAINTAINERS: Update b44 maintainer.
net: get rid of an signed integer overflow in ip_idents_reserve()
net/mlx4_core: Fix to clean devlink resources
net: can: ifi: Configure transmitter delay
vti6: fix input path
ipmr, ip6mr: return lastuse relative to now
r8152: disable ALDPS and EEE before setting PHY
r8152: remove r8153_enable_eee
r8152: move PHY settings to hw_phy_cfg
r8152: move enabling PHY
r8152: move some functions
cxgb4/cxgb4vf: Allocate more queues for 25G and 100G adapter
qed: Fix stack corruption on probe
MAINTAINERS: Add an entry for the core network DSA code
net: ipv6: fallback to full lookup if table lookup is unsuitable
net/mlx5: E-Switch, Handle mode change failures
net/mlx5: E-Switch, Fix error flow in the SRIOV e-switch init code
net/mlx5: Fix flow counter bulk command out mailbox allocation
...
Add support of an offset value for incremental counter and random. With
this option the sysadmin is able to start the counter to a certain value
and then apply the generated number.
Example:
meta mark set numgen inc mod 2 offset 100
This will generate marks with the serie 100, 101, 100, 101, ...
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
-----BEGIN PGP SIGNATURE-----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=3zfm
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160922-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Preparation for slow-start algorithm [ver #2]
Here are some patches that prepare for improvements in ACK generation and
for the implementation of the slow-start part of the protocol:
(1) Stop storing the protocol header in the Tx socket buffers, but rather
generate it on the fly. This potentially saves a little space and
makes it easier to alter the header just before transmission (the
flags may get altered and the serial number has to be changed).
(2) Mask off the Tx buffer annotations and add a flag to record which ones
have already been resent.
(3) Track RTT on a per-peer basis for use in future changes. Tracepoints
are added to log this.
(4) Send PING ACKs in response to incoming calls to elicit a PING-RESPONSE
ACK from which RTT data can be calculated. The response also carries
other useful information.
(5) Expedite PING-RESPONSE ACK generation from sendmsg. If we're actively
using sendmsg, this allows us, under some circumstances, to avoid
having to rely on the background work item to run to generate this
ACK.
This requires ktime_sub_ms() to be added.
(6) Set the REQUEST-ACK flag on some DATA packets to elicit ACK-REQUESTED
ACKs from which RTT data can be calculated.
(7) Limit the use of pings and ACK requests for RTT determination.
Changes:
(V2) Don't use the C division operator for 64-bit division. One instance
should use do_div() and the other should be using nsecs_to_jiffies().
The last two patches got transposed, leading to an undefined symbol
in one of them.
Reported-by: kbuild test robot <lkp@intel.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't want to send a PING ACK for every new incoming call as that just
adds to the network traffic. Instead, we send a PING ACK to the first
three that we receive and then once per second thereafter.
This could probably be made adjustable in future.
Signed-off-by: David Howells <dhowells@redhat.com>
Reduce the number of ACK-Requests we set on DATA packets that we're sending
to reduce network traffic. We set the flag on odd-numbered DATA packets to
start off the RTT cache until we have at least three entries in it and then
probe once per second thereafter to keep it topped up.
This could be made tunable in future.
Note that from this point, the RXRPC_REQUEST_ACK flag is set on DATA
packets as we transmit them and not stored statically in the sk_buff.
Signed-off-by: David Howells <dhowells@redhat.com>
Since the TFO socket is accepted right off SYN-data, the socket
owner can call getsockopt(TCP_INFO) to collect ongoing SYN-ACK
retransmission or timeout stats (i.e., tcpi_total_retrans,
tcpi_retransmits). Currently those stats are only updated
upon handshake completes. This patch fixes it.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes these under-accounting SNMP rtx stats
LINUX_MIB_TCPFORWARDRETRANS
LINUX_MIB_TCPFASTRETRANS
LINUX_MIB_TCPSLOWSTARTRETRANS
when retransmitting TSO packets
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to sending a PING ACK to gain RTT data, we can set the
RXRPC_REQUEST_ACK flag on a DATA packet and get a REQUESTED-ACK ACK. The
ACK packet contains the serial number of the packet it is in response to,
so we can look through the Tx buffer for a matching DATA packet.
This requires that the data packets be stamped with the time of
transmission as a ktime rather than having the resend_at time in jiffies.
This further requires the resend code to do the resend determination in
ktimes and convert to jiffies to set the timer.
Signed-off-by: David Howells <dhowells@redhat.com>
Expedite the transmission of a response to a PING ACK by sending it from
sendmsg if one is pending. We're most likely to see a PING ACK during the
client call Tx phase as the other side may use it to determine a number of
parameters, such as the client's receive window size, the RTT and whether
the client is doing slow start (similar to RFC5681).
If we don't expedite it, it's left to the background processing thread to
transmit.
Signed-off-by: David Howells <dhowells@redhat.com>
Send a PING ACK packet to the peer when we get a new incoming call from a
peer we don't have a record for. The PING RESPONSE ACK packet will tell us
the following about the peer:
(1) its receive window size
(2) its MTU sizes
(3) its support for jumbo DATA packets
(4) if it supports slow start (similar to RFC 5681)
(5) an estimate of the RTT
This is necessary because the peer won't normally send us an ACK until it
gets to the Rx phase and we send it a packet, but we would like to know
some of this information before we start sending packets.
A pair of tracepoints are added so that RTT determination can be observed.
Signed-off-by: David Howells <dhowells@redhat.com>
And avoid the usage of '&~3'. This is the last place still not using
the macro.
Also break the line to make it easier to read.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To something more meaningful these days, specially because this is
working on packet headers or lengths and which are not tied to any CPU
arch but to the protocol itself.
So, WORD_TRUNC becomes SCTP_TRUNC4 and WORD_ROUND becomes SCTP_PAD4.
Reported-by: David Laight <David.Laight@ACULAB.COM>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2016-09-21
1) Propagate errors on security context allocation.
From Mathias Krause.
2) Fix inbound policy checks for inter address family tunnels.
From Thomas Zeitlhofer.
3) Fix an old memory leak on aead algorithm usage.
From Ilan Tayari.
4) A recent patch fixed a possible NULL pointer dereference
but broke the vti6 input path.
Fix from Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We saw sch_fq drops caused by the per flow limit of 100 packets and TCP
when dealing with large cwnd and bursts of retransmits.
Even after increasing the limit to 1000, and even after commit
10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time"),
we can still have these drops.
Under certain conditions, TCP can spend a considerable amount of
time queuing thousands of skbs in a single tcp_xmit_retransmit_queue()
invocation, incurring latency spikes and stalls of other softirq
handlers.
This patch implements TSQ for retransmits, limiting number of packets
and giving more chance for scheduling packets in both ways.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko reported an UBSAN warning happening in ip_idents_reserve()
[] UBSAN: Undefined behaviour in ./arch/x86/include/asm/atomic.h:156:11
[] signed integer overflow:
[] -2117905507 + -695755206 cannot be represented in type 'int'
Since we do not have uatomic_add_return() yet, use atomic_cmpxchg()
so that the arithmetics can be done using unsigned int.
Fixes: 04ca6973f7 ("ip: make IP identifiers less predictable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 'skb_vlan_pop' to use eth_type_vlan instead of directly comparing
skb->protocol to ETH_P_8021Q or ETH_P_8021AD.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 93515d53b1
"net: move vlan pop/push functions into common code"
skb_vlan_pop was moved from its private location in openvswitch to
skbuff common code.
In case skb has non hw-accel vlan tag, the original 'pop_vlan()' assured
that skb->len is sufficient (if skb->len < VLAN_ETH_HLEN then pop was
considered a no-op).
This validation was moved as is into the new common 'skb_vlan_pop'.
Alas, in its original location (openvswitch), there was a guarantee that
'data' points to the mac_header, therefore the 'skb->len < VLAN_ETH_HLEN'
condition made sense.
However there's no such guarantee in the generic 'skb_vlan_pop'.
For short packets received in rx path going through 'skb_vlan_pop',
this causes 'skb_vlan_pop' to fail pop-ing a valid vlan hdr (in the non
hw-accel case) or to fail moving next tag into hw-accel tag.
Remove the 'skb->len < VLAN_ETH_HLEN' condition entirely:
It is superfluous since inner '__skb_vlan_pop' already verifies there
are VLAN_ETH_HLEN writable bytes at the mac_header.
Note this presents a slight change to skb_vlan_pop() users:
In case total length is smaller than VLAN_ETH_HLEN, skb_vlan_pop() now
returns an error, as opposed to previous "no-op" behavior.
Existing callers (e.g. tc act vlan, ovs) usually drop the packet if
'skb_vlan_pop' fails.
Fixes: 93515d53b1 ("net: move vlan pop/push functions into common code")
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Pravin Shelar <pshelar@ovn.org>
Reviewed-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCA_VLAN_ACT_MODIFY allows one to change an existing tag.
It accepts same attributes as TCA_VLAN_ACT_PUSH (protocol, id,
priority).
If packet is vlan tagged, then the tag gets overwritten according to
user specified attributes.
For example, this allows user to replace a tag's vid while preserving
its priority bits (as opposed to "action vlan pop pipe action vlan push").
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This exports the functionality of extracting the tag from the payload,
without moving next vlan tag into hw accel tag.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to track the average RTT for a peer. Sources of RTT data
will be added in subsequent patches.
The RTT data will be useful in the future for determining resend timeouts
and for handling the slow-start part of the Rx protocol.
Also add a pair of tracepoints, one to log transmissions to elicit a
response for RTT purposes and one to log responses that contribute RTT
data.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a Tx-phase annotation for packet buffers to indicate that a buffer has
already been retransmitted. This will be used by future congestion
management. Re-retransmissions of a packet don't affect the congestion
window managment in the same way as initial retransmissions.
Signed-off-by: David Howells <dhowells@redhat.com>
Don't store the rxrpc protocol header in sk_buffs on the transmit queue,
but rather generate it on the fly and pass it to kernel_sendmsg() as a
separate iov. This reduces the amount of storage required.
Note that the security header is still stored in the sk_buff as it may get
encrypted along with the data (and doesn't change with each transmission).
Signed-off-by: David Howells <dhowells@redhat.com>
Implement .stats_update() callback. The implementation
is generic and can be reused by other simple actions if
needed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call into offloaded filters to update stats.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cls_bpf support for the TCA_CLS_FLAGS_SKIP_SW flag.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cls_bpf support for the TCA_CLS_FLAGS_SKIP_HW flag.
Unlike U32 and flower cls_bpf already has some netlink
flags defined. Create a new attribute to be able to use
the same flag values as the above.
Unlike U32 and flower reject unknown flags.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds hardware offload capability to cls_bpf classifier,
similar to what have been done with U32 and flower.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is called from the packet input path, we get lock contention
if many cpus handle ipsec in parallel.
After recent rcu conversion it is safe to call __xfrm_state_lookup
without the spinlock.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Since commit 1625f45299, vti6 is broken, all input packets are dropped
(LINUX_MIB_XFRMINNOSTATES is incremented).
XFRM_TUNNEL_SKB_CB(skb)->tunnel.ip6 is set by vti6_rcv() before calling
xfrm6_rcv()/xfrm6_rcv_spi(), thus we cannot set to NULL that value in
xfrm6_rcv_spi().
A new function xfrm6_rcv_tnl() that enables to pass a value to
xfrm6_rcv_spi() is added, so that xfrm6_rcv() is not touched (this function
is used in several handlers).
CC: Alexey Kodanev <alexey.kodanev@oracle.com>
Fixes: 1625f45299 ("net/xfrm_input: fix possible NULL deref of tunnel.ip6->parms.i_key")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When I introduced the lastuse member I made a subtle error because it was
returned as an absolute value but that is meaningless to user-space as it
doesn't allow to see how old exactly an entry is. Let's make it similar to
how the bridge returns such values and make it relative to "now" (jiffies).
This allows us to show the actual age of the entries and is much more
useful (e.g. user-space daemons can age out entries, iproute2 can display
the lastuse properly).
Fixes: 43b9e12740 ("net: ipmr/ip6mr: add support for keeping an entry age")
Reported-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit implements a new TCP congestion control algorithm: BBR
(Bottleneck Bandwidth and RTT). A detailed description of BBR will be
published in ACM Queue, Vol. 14 No. 5, September-October 2016, as
"BBR: Congestion-Based Congestion Control".
BBR has significantly increased throughput and reduced latency for
connections on Google's internal backbone networks and google.com and
YouTube Web servers.
BBR requires only changes on the sender side, not in the network or
the receiver side. Thus it can be incrementally deployed on today's
Internet, or in datacenters.
The Internet has predominantly used loss-based congestion control
(largely Reno or CUBIC) since the 1980s, relying on packet loss as the
signal to slow down. While this worked well for many years, loss-based
congestion control is unfortunately out-dated in today's networks. On
today's Internet, loss-based congestion control causes the infamous
bufferbloat problem, often causing seconds of needless queuing delay,
since it fills the bloated buffers in many last-mile links. On today's
high-speed long-haul links using commodity switches with shallow
buffers, loss-based congestion control has abysmal throughput because
it over-reacts to losses caused by transient traffic bursts.
In 1981 Kleinrock and Gale showed that the optimal operating point for
a network maximizes delivered bandwidth while minimizing delay and
loss, not only for single connections but for the network as a
whole. Finding that optimal operating point has been elusive, since
any single network measurement is ambiguous: network measurements are
the result of both bandwidth and propagation delay, and those two
cannot be measured simultaneously.
While it is impossible to disambiguate any single bandwidth or RTT
measurement, a connection's behavior over time tells a clearer
story. BBR uses a measurement strategy designed to resolve this
ambiguity. It combines these measurements with a robust servo loop
using recent control systems advances to implement a distributed
congestion control algorithm that reacts to actual congestion, not
packet loss or transient queue delay, and is designed to converge with
high probability to a point near the optimal operating point.
In a nutshell, BBR creates an explicit model of the network pipe by
sequentially probing the bottleneck bandwidth and RTT. On the arrival
of each ACK, BBR derives the current delivery rate of the last round
trip, and feeds it through a windowed max-filter to estimate the
bottleneck bandwidth. Conversely it uses a windowed min-filter to
estimate the round trip propagation delay. The max-filtered bandwidth
and min-filtered RTT estimates form BBR's model of the network pipe.
Using its model, BBR sets control parameters to govern sending
behavior. The primary control is the pacing rate: BBR applies a gain
multiplier to transmit faster or slower than the observed bottleneck
bandwidth. The conventional congestion window (cwnd) is now the
secondary control; the cwnd is set to a small multiple of the
estimated BDP (bandwidth-delay product) in order to allow full
utilization and bandwidth probing while bounding the potential amount
of queue at the bottleneck.
When a BBR connection starts, it enters STARTUP mode and applies a
high gain to perform an exponential search to quickly probe the
bottleneck bandwidth (doubling its sending rate each round trip, like
slow start). However, instead of continuing until it fills up the
buffer (i.e. a loss), or until delay or ACK spacing reaches some
threshold (like Hystart), it uses its model of the pipe to estimate
when that pipe is full: it estimates the pipe is full when it notices
the estimated bandwidth has stopped growing. At that point it exits
STARTUP and enters DRAIN mode, where it reduces its pacing rate to
drain the queue it estimates it has created.
Then BBR enters steady state. In steady state, PROBE_BW mode cycles
between first pacing faster to probe for more bandwidth, then pacing
slower to drain any queue that created if no more bandwidth was
available, and then cruising at the estimated bandwidth to utilize the
pipe without creating excess queue. Occasionally, on an as-needed
basis, it sends significantly slower to probe for RTT (PROBE_RTT
mode).
BBR has been fully deployed on Google's wide-area backbone networks
and we're experimenting with BBR on Google.com and YouTube on a global
scale. Replacing CUBIC with BBR has resulted in significant
improvements in network latency and application (RPC, browser, and
video) metrics. For more details please refer to our upcoming ACM
Queue publication.
Example performance results, to illustrate the difference between BBR
and CUBIC:
Resilience to random loss (e.g. from shallow buffers):
Consider a netperf TCP_STREAM test lasting 30 secs on an emulated
path with a 10Gbps bottleneck, 100ms RTT, and 1% packet loss
rate. CUBIC gets 3.27 Mbps, and BBR gets 9150 Mbps (2798x higher).
Low latency with the bloated buffers common in today's last-mile links:
Consider a netperf TCP_STREAM test lasting 120 secs on an emulated
path with a 10Mbps bottleneck, 40ms RTT, and 1000-packet bottleneck
buffer. Both fully utilize the bottleneck bandwidth, but BBR
achieves this with a median RTT 25x lower (43 ms instead of 1.09
secs).
Our long-term goal is to improve the congestion control algorithms
used on the Internet. We are hopeful that BBR can help advance the
efforts toward this goal, and motivate the community to do further
research.
Test results, performance evaluations, feedback, and BBR-related
discussions are very welcome in the public e-mail list for BBR:
https://groups.google.com/forum/#!forum/bbr-dev
NOTE: BBR *must* be used with the fq qdisc ("man tc-fq") with pacing
enabled, since pacing is integral to the BBR design and
implementation. BBR without pacing would not function properly, and
may incur unnecessary high packet loss rates.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit introduces an optional new "omnipotent" hook,
cong_control(), for congestion control modules. The cong_control()
function is called at the end of processing an ACK (i.e., after
updating sequence numbers, the SACK scoreboard, and loss
detection). At that moment we have precise delivery rate information
the congestion control module can use to control the sending behavior
(using cwnd, TSO skb size, and pacing rate) in any CA state.
This function can also be used by a congestion control that prefers
not to use the default cwnd reduction approach (i.e., the PRR
algorithm) during CA_Recovery to control the cwnd and sending rate
during loss recovery.
We take advantage of the fact that recent changes defer the
retransmission or transmission of new data (e.g. by F-RTO) in recovery
until the new tcp_cong_control() function is run.
With this commit, we only run tcp_update_pacing_rate() if the
congestion control is not using this new API. New congestion controls
which use the new API do not want the TCP stack to run the default
pacing rate calculation and overwrite whatever pacing rate they have
chosen at initialization time.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the TCP send buffer expands to twice cwnd, in order to allow
limited transmits in the CA_Recovery state. This assumes that cwnd
does not increase in the CA_Recovery.
For some congestion control algorithms, like the upcoming BBR module,
if the losses in recovery do not indicate congestion then we may
continue to raise cwnd multiplicatively in recovery. In such cases the
current multiplier will falsely limit the sending rate, much as if it
were limited by the application.
This commit adds an optional congestion control callback to use a
different multiplier to expand the TCP send buffer. For congestion
control modules that do not specificy this callback, TCP continues to
use the previous default of 2.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export tcp_mss_to_mtu(), so that congestion control modules can use
this to help calculate a pacing rate.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow congestion control modules to use the default TSO auto-sizing
algorithm as one of the ingredients in their own decision about TSO sizing:
1) Export tcp_tso_autosize() so that CC modules can use it.
2) Change tcp_tso_autosize() to allow callers to specify a minimum
number of segments per TSO skb, in case the congestion control
module has a different notion of the best floor for TSO skbs for
the connection right now. For very low-rate paths or policed
connections it can be appropriate to use smaller TSO skbs.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the tso_segs_goal() function in tcp_congestion_ops to allow the
congestion control module to specify the number of segments that
should be in a TSO skb sent by tcp_write_xmit() and
tcp_xmit_retransmit_queue(). The congestion control module can either
request a particular number of segments in TSO skb that we transmit,
or return 0 if it doesn't care.
This allows the upcoming BBR congestion control module to select small
TSO skb sizes if the module detects that the bottleneck bandwidth is
very low, or that the connection is policed to a low rate.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit export two new fields in struct tcp_info:
tcpi_delivery_rate: The most recent goodput, as measured by
tcp_rate_gen(). If the socket is limited by the sending
application (e.g., no data to send), it reports the highest
measurement instead of the most recent. The unit is bytes per
second (like other rate fields in tcp_info).
tcpi_delivery_rate_app_limited: A boolean indicating if the goodput
was measured when the socket's throughput was limited by the
sending application.
This delivery rate information can be useful for applications that
want to know the current throughput the TCP connection is seeing,
e.g. adaptive bitrate video streaming. It can also be very useful for
debugging or troubleshooting.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds code to track whether the delivery rate represented
by each rate_sample was limited by the application.
Upon each transmit, we store in the is_app_limited field in the skb a
boolean bit indicating whether there is a known "bubble in the pipe":
a point in the rate sample interval where the sender was
application-limited, and did not transmit even though the cwnd and
pacing rate allowed it.
This logic marks the flow app-limited on a write if *all* of the
following are true:
1) There is less than 1 MSS of unsent data in the write queue
available to transmit.
2) There is no packet in the sender's queues (e.g. in fq or the NIC
tx queue).
3) The connection is not limited by cwnd.
4) There are no lost packets to retransmit.
The tcp_rate_check_app_limited() code in tcp_rate.c determines whether
the connection is application-limited at the moment. If the flow is
application-limited, it sets the tp->app_limited field. If the flow is
application-limited then that means there is effectively a "bubble" of
silence in the pipe now, and this silence will be reflected in a lower
bandwidth sample for any rate samples from now until we get an ACK
indicating this bubble has exited the pipe: specifically, until we get
an ACK for the next packet we transmit.
When we send every skb we record in scb->tx.is_app_limited whether the
resulting rate sample will be application-limited.
The code in tcp_rate_gen() checks to see when it is safe to mark all
known application-limited bubbles of silence as having exited the
pipe. It does this by checking to see when the delivered count moves
past the tp->app_limited marker. At this point it zeroes the
tp->app_limited marker, as all known bubbles are out of the pipe.
We make room for the tx.is_app_limited bit in the skb by borrowing a
bit from the in_flight field used by NV to record the number of bytes
in flight. The receive window in the TCP header is 16 bits, and the
max receive window scaling shift factor is 14 (RFC 1323). So the max
receive window offered by the TCP protocol is 2^(16+14) = 2^30. So we
only need 30 bits for the tx.in_flight used by NV.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generates data delivery rate (throughput) samples on a
per-ACK basis. These rate samples can be used by congestion control
modules, and specifically will be used by TCP BBR in later patches in
this series.
Key state:
tp->delivered: Tracks the total number of data packets (original or not)
delivered so far. This is an already-existing field.
tp->delivered_mstamp: the last time tp->delivered was updated.
Algorithm:
A rate sample is calculated as (d1 - d0)/(t1 - t0) on a per-ACK basis:
d1: the current tp->delivered after processing the ACK
t1: the current time after processing the ACK
d0: the prior tp->delivered when the acked skb was transmitted
t0: the prior tp->delivered_mstamp when the acked skb was transmitted
When an skb is transmitted, we snapshot d0 and t0 in its control
block in tcp_rate_skb_sent().
When an ACK arrives, it may SACK and ACK some skbs. For each SACKed
or ACKed skb, tcp_rate_skb_delivered() updates the rate_sample struct
to reflect the latest (d0, t0).
Finally, tcp_rate_gen() generates a rate sample by storing
(d1 - d0) in rs->delivered and (t1 - t0) in rs->interval_us.
One caveat: if an skb was sent with no packets in flight, then
tp->delivered_mstamp may be either invalid (if the connection is
starting) or outdated (if the connection was idle). In that case,
we'll re-stamp tp->delivered_mstamp.
At first glance it seems t0 should always be the time when an skb was
transmitted, but actually this could over-estimate the rate due to
phase mismatch between transmit and ACK events. To track the delivery
rate, we ensure that if packets are in flight then t0 and and t1 are
times at which packets were marked delivered.
If the initial and final RTTs are different then one may be corrupted
by some sort of noise. The noise we see most often is sending gaps
caused by delayed, compressed, or stretched acks. This either affects
both RTTs equally or artificially reduces the final RTT. We approach
this by recording the info we need to compute the initial RTT
(duration of the "send phase" of the window) when we recorded the
associated inflight. Then, for a filter to avoid bandwidth
overestimates, we generalize the per-sample bandwidth computation
from:
bw = delivered / ack_phase_rtt
to the following:
bw = delivered / max(send_phase_rtt, ack_phase_rtt)
In large-scale experiments, this filtering approach incorporating
send_phase_rtt is effective at avoiding bandwidth overestimates due to
ACK compression or stretched ACKs.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count the number of packets that a TCP connection marks lost.
Congestion control modules can use this loss rate information for more
intelligent decisions about how fast to send.
Specifically, this is used in TCP BBR policer detection. BBR uses a
high packet loss rate as one signal in its policer detection and
policer bandwidth estimation algorithm.
The BBR policer detection algorithm cannot simply track retransmits,
because a retransmit can be (and often is) an indicator of packets
lost long, long ago. This is particularly true in a long CA_Loss
period that repairs the initial massive losses when a policer kicks
in.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert to the tcp_skb_cb size check that tcp_init() had before commit
b4772ef879 ("net: use common macro for assering skb->cb[] available
size in protocol families"). As related commit 744d5a3e9f ("net:
move skb->dropcount to skb->cb[]") explains, the
sock_skb_cb_check_size() mechanism was added to ensure that there is
space for dropcount, "for protocol families using it". But TCP is not
a protocol using dropcount, so tcp_init() doesn't need to provision
space for dropcount in the skb->cb[], and thus we can revert to the
older form of the tcp_skb_cb size check. Doing so allows TCP to use 4
more bytes of the skb->cb[] space.
Fixes: b4772ef879 ("net: use common macro for assering skb->cb[] available size in protocol families")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds to the fq module a low_rate_threshold parameter to
insert a delay after all packets if the socket requests a pacing rate
below the threshold.
This helps achieve more precise control of the sending rate with
low-rate paths, especially policers. The basic issue is that if a
congestion control module detects a policer at a certain rate, it may
want fq to be able to shape to that policed rate. That way the sender
can avoid policer drops by having the packets arrive at the policer at
or just under the policed rate.
The default threshold of 550Kbps was chosen analytically so that for
policers or links at 500Kbps or 512Kbps fq would very likely invoke
this mechanism, even if the pacing rate was briefly slightly above the
available bandwidth. This value was then empirically validated with
two years of production testing on YouTube video servers.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the TCP min_rtt code to reuse the new win_minmax library in
lib/win_minmax.c to simplify the TCP code.
This is a pure refactor: the functionality is exactly the same. We
just moved the windowed min code to make TCP easier to read and
maintain, and to allow other parts of the kernel to use the windowed
min/max filter code.
Signed-off-by: Van Jacobson <vanj@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upcoming change "lib/win_minmax: windowed min or max estimator"
introduces a struct called minmax, which is then included in
include/linux/tcp.h in the upcoming change "tcp: use windowed min
filter library for TCP min_rtt estimation". This would create a
compilation error for tcp_cdg.c, which defines its own minmax
struct. To avoid this naming conflict (and potentially others in the
future), this commit renames the version used in tcp_cdg.c to
cdg_minmax.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the batch changes that translated transient actions into
a temporary list lost in the translation was the fact that
tcf_action_destroy() will eventually delete the action from
the permanent location if the refcount is zero.
Example of what broke:
...add a gact action to drop
sudo $TC actions add action drop index 10
...now retrieve it, looks good
sudo $TC actions get action gact index 10
...retrieve it again and find it is gone!
sudo $TC actions get action gact index 10
Fixes: 22dc13c837 ("net_sched: convert tcf_exts from list to pointer array"),
Fixes: 824a7e8863 ("net_sched: remove an unnecessary list_del()")
Fixes: f07fed82ad ("net_sched: remove the leftover cleanup_a()")
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work implements direct packet access for helpers and direct packet
write in a similar fashion as already available for XDP types via commits
4acf6c0b84 ("bpf: enable direct packet data write for xdp progs") and
6841de8b0d ("bpf: allow helpers access the packet directly"), and as a
complementary feature to the already available direct packet read for tc
(cls/act) programs.
For enabling this, we need to introduce two helpers, bpf_skb_pull_data()
and bpf_csum_update(). The first is generally needed for both, read and
write, because they would otherwise only be limited to the current linear
skb head. Usually, when the data_end test fails, programs just bail out,
or, in the direct read case, use bpf_skb_load_bytes() as an alternative
to overcome this limitation. If such data sits in non-linear parts, we
can just pull them in once with the new helper, retest and eventually
access them.
At the same time, this also makes sure the skb is uncloned, which is, of
course, a necessary condition for direct write. As this needs to be an
invariant for the write part only, the verifier detects writes and adds
a prologue that is calling bpf_skb_pull_data() to effectively unclone the
skb from the very beginning in case it is indeed cloned. The heuristic
makes use of a similar trick that was done in 233577a220 ("net: filter:
constify detection of pkt_type_offset"). This comes at zero cost for other
programs that do not use the direct write feature. Should a program use
this feature only sparsely and has read access for the most parts with,
for example, drop return codes, then such write action can be delegated
to a tail called program for mitigating this cost of potential uncloning
to a late point in time where it would have been paid similarly with the
bpf_skb_store_bytes() as well. Advantage of direct write is that the
writes are inlined whereas the helper cannot make any length assumptions
and thus needs to generate a call to memcpy() also for small sizes, as well
as cost of helper call itself with sanity checks are avoided. Plus, when
direct read is already used, we don't need to cache or perform rechecks
on the data boundaries (due to verifier invalidating previous checks for
helpers that change skb->data), so more complex programs using rewrites
can benefit from switching to direct read plus write.
For direct packet access to helpers, we save the otherwise needed copy into
a temp struct sitting on stack memory when use-case allows. Both facilities
are enabled via may_access_direct_pkt_data() in verifier. For now, we limit
this to map helpers and csum_diff, and can successively enable other helpers
where we find it makes sense. Helpers that definitely cannot be allowed for
this are those part of bpf_helper_changes_skb_data() since they can change
underlying data, and those that write into memory as this could happen for
packet typed args when still cloned. bpf_csum_update() helper accommodates
for the fact that we need to fixup checksum_complete when using direct write
instead of bpf_skb_store_bytes(), meaning the programs can use available
helpers like bpf_csum_diff(), and implement csum_add(), csum_sub(),
csum_block_add(), csum_block_sub() equivalents in eBPF together with the
new helper. A usage example will be provided for iproute2's examples/bpf/
directory.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
since commit commit db74a3335e ("openvswitch: use percpu
flow stats") flow alloc resets flow-key. So there is no need
to reset the flow-key again if OVS is using newly allocated
flow-key.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to declare separate key on stack,
we can just use sw_flow->key to store the key directly.
This commit fixes following warning:
net/openvswitch/datapath.c: In function ‘ovs_flow_cmd_new’:
net/openvswitch/datapath.c:1080:1: warning: the frame size of 1040 bytes
is larger than 1024 bytes [-Wframe-larger-than=]
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-09-19
Here's the main bluetooth-next pull request for the 4.9 kernel.
- Added new messages for monitor sockets for better mgmt tracing
- Added local name and appearance support in scan response
- Added new Qualcomm WCNSS SMD based HCI driver
- Minor fixes & cleanup to 802.15.4 code
- New USB ID to btusb driver
- Added Marvell support to HCI UART driver
- Add combined LED trigger for controller power
- Other minor fixes here and there
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only 1 of the 3 drivers currently has a set_addr() operation. Make the
set_addr() callback optional to reduce the amount of empty stubs inside
the drivers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 83c0afaec7 ("net: dsa: Add new binding implementation")
has a duplicate invocation of the set_addr() operation callback. Remove one
of them.
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 currently uses rhashtable with insecure_elasticity set
to true. The latter is because of duplicate objects. What's
more, mac80211 walks the rhashtable chains by hand which is broken
as rhashtable may contain multiple tables due to resizing or
rehashing.
This patch fixes it by converting it to the newly added rhltable
interface which is designed for use with duplicate objects.
With rhltable a lookup returns a list of objects instead of a
single one. This is then fed into the existing for_each_sta_info
macro.
This patch also deletes the sta_addr_hash function since rhashtable
defaults to jhash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8c14586fc3 ("net: ipv6: Use passed in table for nexthop
lookups") introduced a regression: insertion of an IPv6 route in a table
not containing the appropriate connected route for the gateway but which
contained a non-connected route (like a default gateway) fails while it
was previously working:
$ ip link add eth0 type dummy
$ ip link set up dev eth0
$ ip addr add 2001:db8::1/64 dev eth0
$ ip route add ::/0 via 2001:db8::5 dev eth0 table 20
$ ip route add 2001:db8:cafe::1/128 via 2001:db8::6 dev eth0 table 20
RTNETLINK answers: No route to host
$ ip -6 route show table 20
default via 2001:db8::5 dev eth0 metric 1024 pref medium
After this patch, we get:
$ ip route add 2001:db8:cafe::1/128 via 2001:db8::6 dev eth0 table 20
$ ip -6 route show table 20
2001:db8:cafe::1 via 2001:db8::6 dev eth0 metric 1024 pref medium
default via 2001:db8::5 dev eth0 metric 1024 pref medium
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
setting conforming action to drop is a valid policy.
When it is set we need to at least see the stats indicating it
for debugging.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sample use case of how this is encoded:
user space via tuntap (or a connected VM/Machine/container)
encodes the tcindex TLV.
Sample use case of decoding:
IFE action decodes it and the skb->tc_index is then used to classify.
So something like this for encoded ICMP packets:
.. first decode then reclassify... skb->tcindex will be set
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xbeef \
u32 match u32 0 0 flowid 1:1 \
action ife decode reclassify
...next match the decode icmp packet...
sudo $TC filter add dev $ETH parent ffff: prio 4 protocol ip \
u32 match ip protocol 1 0xff flowid 1:1 \
action continue
... last classify it using the tcindex classifier and do someaction..
sudo $TC filter add dev $ETH parent ffff: prio 5 protocol ip \
handle 0x11 tcindex classid 1:1 \
action blah..
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 8a29111c7 ("net: gro: allow to build full sized skb")
gro may build buffers with a frag_list. This can hurt forwarding
because most NICs can't offload such packets, they need to be
segmented in software. This patch splits buffers with a frag_list
at the frag_list pointer into buffers that can be TSO offloaded.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a socket is cloned, the associated sock_cgroup_data is duplicated
but not its reference on the cgroup. As a result, the cgroup reference
count will underflow when both sockets are destroyed later on.
Fixes: bd1060a1d6 ("sock, cgroup: add sock->sk_cgroup")
Link: http://lkml.kernel.org/r/20160914194846.11153-2-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: <stable@vger.kernel.org> [4.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting appearance on controllers without LE support will result
in No Supported error.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds missing event when setting appearance, just like
in the set local name command.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds EIR data to extended info changed event.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If LE is enabled appearance is added to EIR data.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This will also be used for Extended Information Event handling.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is no need to allocate heap for reply only to copy stack data to
it. This also fix rp memory leak and missing hdev unlock if kmalloc
failed.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Increment the mgmt revision due to the recently added
Read Extended Controller Information and Set Appearance commands.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch enables prepending appearance value to scan response data.
It also adds support for setting appearance value through mgmt command.
If currently advertised instance has apperance flag set it is expired
immediately.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch enables appending local name to scan response data. If
currently advertised instance has name flag set it is expired
immediately.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use kzalloc rather than kmalloc followed by memset with 0.
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A comment in the code states that SCO connection should be rejected
with the proper error value between 0xd-0xf. The code uses
HCI_ERROR_REMOTE_LOW_RESOURCES which is 0x14.
This led to following error:
< HCI Command: Reject Synchronous Co.. (0x01|0x002a) plen 7
Address: 34:51:C9:EF:02:CA (Apple, Inc.)
Reason: Remote Device Terminated due to Low Resources (0x14)
> HCI Event: Command Status (0x0f) plen 4
Reject Synchronous Connection Request (0x01|0x002a) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
Instead make use of HCI_ERROR_REJ_LIMITED_RESOURCES which is 0xd.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When closing HCI User Channel, the New Settings event was send out to
inform about changed settings. However such event is wrong since the
exclusive HCI User Channel access is active until the Index Added event
has been sent.
@ USER Close: test
@ MGMT Event: New Settings (0x0006) plen 4
Current settings: 0x00000ad0
Bondable
Secure Simple Pairing
BR/EDR
Low Energy
Secure Connections
= Close Index: 00:14:EF:22:04:12
@ MGMT Event: Index Added (0x0004) plen 0
Calling __mgmt_power_off from hci_dev_do_close requires an extra check
for an active HCI User Channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When opening and closing HCI user channel, send monitoring messages to
be able to trace its behavior.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds device class, complete local name and short local name
to EIR data in Extended Controller Info as specified in docs.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This command is used to retrieve the current state and basic
information of a controller. It is typically used right after
getting the response to the Read Controller Index List command
or an Index Added event (or its extended counterparts).
When any of the values in the EIR_Data field changes, the event
Extended Controller Information Changed will be used to inform
clients about the updated information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
In case an unbound HCI raw socket is later on bound, ensure that the
monitor notification messages indicate a close and re-open. None of
the userspace tools use the socket this, but it is actually possible
to use an ioctl on an unbound socket and then later bind it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When opening and closing HCI raw sockets their main usage is for legacy
userspace. To track interaction with the modern mgmt interface, send
open and close monitoring messages for these action.
The HCI raw sockets is special since it supports unbound ioctl operation
and for that special case delay the notification message until at least
one ioctl has been executed. The difference between a bound and unbound
socket will be detailed by the fact the HCI index is present or not.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The control open and close monitoring events require special channel
checks to ensure messages are only send when the right events happen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Assignment of the hci_pi(sk)->channel should be done early when binding
the HCI socket. This avoids confusion with the RAW channel that is used
for legacy access.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Only when the cookie has been assigned, then send the open and close
monitor messages. Also if the socket is bound to a device, then include
the index into the message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of keeping a version string around, use version and revision
numbers and then stringify them for use as module parameter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of manually allocating cookie information each time, use helper
functions for generating and releasing cookies.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case of failure, the Set IO Capability command is suppose to return
command status and not command complete.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The address information of the Get Clock Information return parameters
is copying from a different memory location. It uses &cmd->param while
it actually needs to be cmd->param.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of hiding everything behind a general managment events flag,
introduce indivdual flags that allow fine control over which events are
send to a given management channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When an Advertising Instance is removed, the Advertising Removed event
shouldn't be sent to the same socket that issued the Remove
Advertising command (it gets a command complete event instead). The
mgmt_advertising_removed() function already has a parameter for
skipping a specific socket, but there was no code to propagate the
right value to this parameter. This patch fixes the issue by making
sure the intermediate hci_req_clear_adv_instance() function gets the
socket pointer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
