Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To report channel width correctly we have
to send correct channel parameters from
mac80211 when calling cfg80211_cac_event().
This is required in case of using channel width
higher than 20MHz and we have to set correct
dfs channel state after CAC (NL80211_DFS_AVAILABLE).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The timestamp wasn't updated after transitioning
to the NL80211_DFS_USABLE state after NOP time.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The timeout was not properly converted from msecs
to jiffies. As a result channel transition to
NL80211_DFS_USABLE was delayed depending on
CONFIG_HZ configuration, e.g. HZ=100 would delay
the NOP from 30 minutes to 300 minutes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add flags intended to report various auxiliary information
and introduce the NL80211_RXMGMT_FLAG_ANSWERED flag to report
that the frame was already answered by the device.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[REPLIED->ANSWERED, reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes the potential issue that the BSS struct that we use
and later assign to wdev->current_bss is removed from the scan
list while associating.
Also warn when we don't have a BSS struct in connect_result
unless it's from a driver that only has the connect() API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Doing so will allow us to hold the BSS (not just ref it) over the
association process, thus ensuring that it doesn't time out and
gets invisible to the user (e.g. in 'iw wlan0 link'.)
This also fixes a leak in mac80211 where it doesn't always release
the BSS struct properly in all cases where calling this function.
This leak was reported by Ben Greear.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current internal SME implementation in cfg80211 is
very mixed up with the MLME handling, which has been
causing issues for a long time. There are three things
that the implementation has to provide:
* a basic SME implementation for nl80211's connect()
call (for drivers implementing auth/assoc, which is
really just mac80211) and wireless extensions
* MLME events for the userspace SME
* SME events (connected, disconnected etc.) for all
different SME implementation possibilities (driver,
cfg80211 and userspace)
To achieve these goals it isn't necessary to track the
software SME's connection status outside of it's state
(which is the part that caused many issues.) Instead,
track it only in the SME data (wdev->conn) and in the
general case only track whether the wdev is connected
or not (via wdev->current_bss.)
Also separate the internal implementation to not have
callbacks from the SME events, but rather call it from
the API functions that the driver (or rather mac80211)
calls. This separates the code better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do some cleanups in the cfg80211 SME APIs, which are
only used by mac80211.
Most of these functions get a frame passed, and there
isn't really any reason to export multiple functions
as cfg80211 can check the frame type instead, do that.
Additionally, the API functions have confusing names
like cfg80211_send_...() which was meant to indicate
that it sends an event to userspace, but gets a bit
confusing when there's both TX and RX and they're not
all clearly labeled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Virtually all code paths in cfg80211 already (need to) hold
the RTNL. As such, there's little point in having another
four mutexes for various parts of the code, they just cause
lock ordering issues (and much of the time, the RTNL and a
few of the others need thus be held.)
Simplify all this by getting rid of the extra four mutexes
and just use the RTNL throughout. Only a few code changes
were needed to do this and we can get rid of a work struct
for bonus points.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some protocols need a more reliable connection to complete
successful in reasonable time. This patch adds a user-space
API to indicate the wireless driver that a critical protocol
is about to commence and when it is done, using nl80211 primitives
NL80211_CMD_CRIT_PROTOCOL_START and NL80211_CRIT_PROTOCOL_STOP.
There can be only on critical protocol session started per
registered cfg80211 device.
The driver can support this by implementing the cfg80211 callbacks
.crit_proto_start() and .crit_proto_stop(). Examples of protocols
that can benefit from this are DHCP, EAPOL, APIPA. Exactly how the
link can/should be made more reliable is up to the driver. Things
to consider are avoid scanning, no multi-channel operations, and
alter coexistence schemes.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_mlme_assoc() has grown far too many arguments,
make the caller build almost all of the driver struct
and pass that to the function instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing it's sometimes useful to be able to
override certain VHT capability advertisement,
add the ability to do that in cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the sort of thing gcc's LTO could do, but since
we don't have that yet we can also do it manually. The
advantage is reduced code, both source and binary, e.g.
on x86-64
text data bss dec hex filename
442825 56230 776 499831 7a077 cfg80211.ko (before)
441585 56230 776 498591 79b9f cfg80211.ko (after)
a reduction of ~1k.
But in order to not complicate the code move only those
functions that are simple wrappers, not those that have
functionality of their own.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new NL80211_CMD_RADAR_DETECT, which starts the Channel
Availability Check (CAC). This command will also notify the
usermode about events (CAC finished, CAC aborted, radar
detected, NOP finished).
Once radar detection has started it should continuously
monitor for radars as long as the channel is active.
This patch enables DFS for AP mode in nl80211/cfg80211.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
[remove WIPHY_FLAG_HAS_RADAR_DETECT again -- my mistake]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This prepares for using the spinlock instead of krefs
which is needed in the next patch to track the refs
of combined BSSes correctly.
Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The warning here occasionally triggers but we haven't
found the cause yet. It's a valid warning since if it
triggers the SME state got confused, so add the SME
state to it to help narrow it down in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.
Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Also add tracing to the API functions that drivers
(and mac80211) can call in cfg80211.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow adding central tracing like in mac80211.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE extends Authentication frames with fields that are not information
elements. NL80211_ATTR_IE is not suitable for these, so introduce a new
attribute that can be used to specify the fields needed for SAE in
station mode.
Signed-off-by: Jouni Malinen <j@w1.fi>
[change to verify that SAE is only used with authenticate command]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid situation when we are on associate state in mac80211 and
on disassociate state in cfg80211. This can results on crash
during modules unload (like showed on this thread:
http://marc.info/?t=134373976300001&r=1&w=2) and possibly other
problems.
Reported-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, when a station requests connection to an AP and if the
request is failed for particular reason, userspace is notified about the
failure through NL80211_CMD_CONN_FAILED command. Reason for the failure
is sent through the attribute NL80211_ATTR_CONN_FAILED_REASON.
Signed-off-by: Pandiyarajan Pitchaimuthu <c_ppitch@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is a frequent mistake to confuse the netlink port identifier with a
process identifier. Try to reduce this confusion by renaming fields
that hold port identifiers portid instead of pid.
I have carefully avoided changing the structures exported to
userspace to avoid changing the userspace API.
I have successfully built an allyesconfig kernel with this change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.
This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.
Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.
As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let the user configure serveral TX error conection quality monitoring
parameters: % error rate, survey interval, and # of attempted packets.
On exceeding the TX failure rate over the given interval, the driver
will send a CQM notify event with the actual TX failure rate and
packets attempted.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
devlist_mtx locking is changed to accomodate changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to know which channel is used by a running
AP and mesh for channel context accounting and
finding matching/active interface combination.
STA/IBSS have current_bss already which allows us
to check which channel a vif is tuned to.
Non-fixed channel IBSS can be handled with
additional changes.
Monitor mode is going to be handled differently.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().
Also describe the desired set_monitor_channel()
semantics more clearly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
I removed a conversion from scan.c/cmp_bss_core
that appears to be a sorting function.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware may decide to switch channels while already beaconing, e.g.
in response to a cfg80211 connect request on a different vif. Add this
event to notify userspace when an AP or GO interface has successfully
migrated to a new channel, so it can update its configuration
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the signal strength (in dBm only for now) to
frames that are received via nl80211's various
frame APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To track authenticated state seems to have been
a design mistake in cfg80211. It is possible to
have out of band authentication (FT), tracking
multiple authentications caused more problems
than it ever helped, and the implementation in
mac80211 is too complex.
Remove all this complexity, and let userspace
do whatever it wants to, mac80211 can deal with
that just fine. Association is still tracked of
course, but authentication no longer is. Local
auth state changes are thus no longer of value,
so ignore them completely.
This will also help implement SAE -- asking the
driver to do an authentication is now almost
equivalent to sending an authentication frame,
with the exception of shared key authentication
which is still handled completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows users to disable features such as HT, HT40,
and to modify the MCS, AMPDU, and AMSDU settings for
drivers that support it.
The MCS, AMPDU, and AMSDU features that may be disabled are
are reported in the phy-info netlink message as a mask.
Attemping to disable features that are not supported will
take no affect, but will not return errors. This is to aid
backwards compatibility in user-space apps that may not be
clever enough to deal with parsing the the capabilities mask.
This patch only enables the infrastructure. An additional
patch will enable the feature in mac80211.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For probe responses it can be useful to not wait for ACK to
avoid retransmissions if the station that sent the probe is
already on the next channel, so allow userspace to request
not caring about the ACK with a new nl80211 flag.
Since mac80211 needs to be updated for the new function
prototype anyway implement it right away -- it's just a
few lines of code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The frames are used by AP/STA WDS mode, and hostapd
needs to know when such a frame was received to set
up the VLAN appropriately to allow using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To implement AP mode without monitor interfaces we
need to be able to send a deauth to stations that
send frames without being associated. Enable this
by adding a new nl80211 event for such frames that
an application can subscribe to.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new nl80211 attribute to specify whether to send the management
frames in CCK rate or not. As of now the wpa_supplicant is disabling
CCK rate at P2P init itself. So this patch helps to send P2P probe
request/probe response/action frames being sent at non CCK rate in 2GHz
without disabling 11b rates.
This attribute is used with NL80211_CMD_TRIGGER_SCAN and
NL80211_CMD_FRAME commands to disable CCK rate for management frame
transmission.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver (or most likely firmware) decides which AP to use
for roaming based on internal scan result processing, user space
needs to be notified of PMKSA caching candidates to allow RSN
pre-authentication to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In certain circumstances, like WoWLAN scenarios,
devices may implement (partial) GTK rekeying on
the device to avoid waking up the host for it.
In order to successfully go through GTK rekeying,
the KEK, KCK and the replay counter are required.
Add API to let the supplicant hand the parameters
to the driver which may store it for future GTK
rekey operations.
Note that, of course, if GTK rekeying is done by
the device, the EAP frame must not be passed up
to userspace, instead a rekey event needs to be
sent to let userspace update its replay counter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
