There's a potential leak issue under following execution sequence :
smc_release smc_connect_work
if (sk->sk_state == SMC_INIT)
send_clc_confirim
tcp_abort();
...
sk.sk_state = SMC_ACTIVE
smc_close_active
switch(sk->sk_state) {
...
case SMC_ACTIVE:
smc_close_final()
// then wait peer closed
Unfortunately, tcp_abort() may discard CLC CONFIRM messages that are
still in the tcp send buffer, in which case our connection token cannot
be delivered to the server side, which means that we cannot get a
passive close message at all. Therefore, it is impossible for the to be
disconnected at all.
This patch tries a very simple way to avoid this issue, once the state
has changed to SMC_ACTIVE after tcp_abort(), we can actively abort the
smc connection, considering that the state is SMC_INIT before
tcp_abort(), abandoning the complete disconnection process should not
cause too much problem.
In fact, this problem may exist as long as the CLC CONFIRM message is
not received by the server. Whether a timer should be added after
smc_close_final() needs to be discussed in the future. But even so, this
patch provides a faster release for connection in above case, it should
also be valuable.
Fixes: 39f41f367b ("net/smc: common release code for non-accepted sockets")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a new OpenFlow field OFPXMT_OFB_IPV6_EXTHDR and
packets can be filtered using ipv6_ext flag.
Signed-off-by: Toms Atteka <cpp.code.lv@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no remaining callers of set_fs(), so CONFIG_SET_FS
can be removed globally, along with the thread_info field and
any references to it.
This turns access_ok() into a cheaper check against TASK_SIZE_MAX.
As CONFIG_SET_FS is now gone, drop all remaining references to
set_fs()/get_fs(), mm_segment_t, user_addr_max() and uaccess_kernel().
Acked-by: Sam Ravnborg <sam@ravnborg.org> # for sparc32 changes
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Tested-by: Sergey Matyukevich <sergey.matyukevich@synopsys.com> # for arc changes
Acked-by: Stafford Horne <shorne@gmail.com> # [openrisc, asm-generic]
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Syzkaller with UBSAN uncovered a scenario where a large number of
DATA_FIN retransmits caused a shift-out-of-bounds in the DATA_FIN
timeout calculation:
================================================================================
UBSAN: shift-out-of-bounds in net/mptcp/protocol.c:470:29
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 1 PID: 13059 Comm: kworker/1:0 Not tainted 5.17.0-rc2-00630-g5fbf21c90c60 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Workqueue: events mptcp_worker
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
ubsan_epilogue+0xb/0x5a lib/ubsan.c:151
__ubsan_handle_shift_out_of_bounds.cold+0xb2/0x20e lib/ubsan.c:330
mptcp_set_datafin_timeout net/mptcp/protocol.c:470 [inline]
__mptcp_retrans.cold+0x72/0x77 net/mptcp/protocol.c:2445
mptcp_worker+0x58a/0xa70 net/mptcp/protocol.c:2528
process_one_work+0x9df/0x16d0 kernel/workqueue.c:2307
worker_thread+0x95/0xe10 kernel/workqueue.c:2454
kthread+0x2f4/0x3b0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
================================================================================
This change limits the maximum timeout by limiting the size of the
shift, which keeps all intermediate values in-bounds.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/259
Fixes: 6477dd39e6 ("mptcp: Retransmit DATA_FIN")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MPTCP SIOCOUTQ implementation is not very accurate in
case of fallback: it only measures the data in the MPTCP-level
write queue, but it does not take in account the subflow
write queue utilization. In case of fallback the first can be
empty, while the latter is not.
The above produces sporadic self-tests issues and can foul
legit user-space application.
Fix the issue additionally querying the subflow in case of fallback.
Fixes: 644807e3e4 ("mptcp: add SIOCINQ, OUTQ and OUTQNSD ioctls")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/260
Reported-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The functions do essentially the same work to verify TCP-MD5 sign.
Code can be merged into one family-independent function in order to
reduce copy'n'paste and generated code.
Later with TCP-AO option added, this will allow to create one function
that's responsible for segment verification, that will have all the
different checks for MD5/AO/non-signed packets, which in turn will help
to see checks for all corner-cases in one function, rather than spread
around different families and functions.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220223175740.452397-1-dima@arista.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change introduces support for installing static FDB entries towards
a bridge port that is a LAG of multiple DSA switch ports, as well as
support for filtering towards the CPU local FDB entries emitted for LAG
interfaces that are bridge ports.
Conceptually, host addresses on LAG ports are identical to what we do
for plain bridge ports. Whereas FDB entries _towards_ a LAG can't simply
be replicated towards all member ports like we do for multicast, or VLAN.
Instead we need new driver API. Hardware usually considers a LAG to be a
"logical port", and sets the entire LAG as the forwarding destination.
The physical egress port selection within the LAG is made by hashing
policy, as usual.
To represent the logical port corresponding to the LAG, we pass by value
a copy of the dsa_lag structure to all switches in the tree that have at
least one port in that LAG.
To illustrate why a refcounted list of FDB entries is needed in struct
dsa_lag, it is enough to say that:
- a LAG may be a bridge port and may therefore receive FDB events even
while it isn't yet offloaded by any DSA interface
- DSA interfaces may be removed from a LAG while that is a bridge port;
we don't want FDB entries lingering around, but we don't want to
remove entries that are still in use, either
For all the cases below to work, the idea is to always keep an FDB entry
on a LAG with a reference count equal to the DSA member ports. So:
- if a port joins a LAG, it requests the bridge to replay the FDB, and
the FDB entries get created, or their refcount gets bumped by one
- if a port leaves a LAG, the FDB replay deletes or decrements refcount
by one
- if an FDB is installed towards a LAG with ports already present, that
entry is created (if it doesn't exist) and its refcount is bumped by
the amount of ports already present in the LAG
echo "Adding FDB entry to bond with existing ports"
ip link del bond0
ip link add bond0 type bond mode 802.3ad
ip link set swp1 down && ip link set swp1 master bond0 && ip link set swp1 up
ip link set swp2 down && ip link set swp2 master bond0 && ip link set swp2 up
ip link del br0
ip link add br0 type bridge
ip link set bond0 master br0
bridge fdb add dev bond0 00:01:02:03:04:05 master static
ip link del br0
ip link del bond0
echo "Adding FDB entry to empty bond"
ip link del bond0
ip link add bond0 type bond mode 802.3ad
ip link del br0
ip link add br0 type bridge
ip link set bond0 master br0
bridge fdb add dev bond0 00:01:02:03:04:05 master static
ip link set swp1 down && ip link set swp1 master bond0 && ip link set swp1 up
ip link set swp2 down && ip link set swp2 master bond0 && ip link set swp2 up
ip link del br0
ip link del bond0
echo "Adding FDB entry to empty bond, then removing ports one by one"
ip link del bond0
ip link add bond0 type bond mode 802.3ad
ip link del br0
ip link add br0 type bridge
ip link set bond0 master br0
bridge fdb add dev bond0 00:01:02:03:04:05 master static
ip link set swp1 down && ip link set swp1 master bond0 && ip link set swp1 up
ip link set swp2 down && ip link set swp2 master bond0 && ip link set swp2 up
ip link set swp1 nomaster
ip link set swp2 nomaster
ip link del br0
ip link del bond0
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When switchdev_handle_fdb_event_to_device() replicates a FDB event
emitted for the bridge or for a LAG port and DSA offloads that, we
should notify back to switchdev that the FDB entry on the original
device is what was offloaded, not on the DSA slave devices that the
event is replicated on.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By construction, the struct net_device *dev passed to
dsa_slave_switchdev_event_work() via struct dsa_switchdev_event_work
is always a DSA slave device.
Therefore, it is redundant to pass struct dsa_switch and int port
information in the deferred work structure. This can be retrieved at all
times from the provided struct net_device via dsa_slave_to_port().
For the same reason, we can drop the dsa_is_user_port() check in
dsa_fdb_offload_notify().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the switchdev_handle_fdb_event_to_device() event replication helper
was created, my original thought was that FDB events on LAG interfaces
should most likely be special-cased, not just replicated towards all
switchdev ports beneath that LAG. So this replication helper currently
does not recurse through switchdev lower interfaces of LAG bridge ports,
but rather calls the lag_mod_cb() if that was provided.
No switchdev driver uses this helper for FDB events on LAG interfaces
yet, so that was an assumption which was yet to be tested. It is
certainly usable for that purpose, as my RFC series shows:
https://patchwork.kernel.org/project/netdevbpf/cover/20220210125201.2859463-1-vladimir.oltean@nxp.com/
however this approach is slightly convoluted because:
- the switchdev driver gets a "dev" that isn't its own net device, but
rather the LAG net device. It must call switchdev_lower_dev_find(dev)
in order to get a handle of any of its own net devices (the ones that
pass check_cb).
- in order for FDB entries on LAG ports to be correctly refcounted per
the number of switchdev ports beneath that LAG, we haven't escaped the
need to iterate through the LAG's lower interfaces. Except that is now
the responsibility of the switchdev driver, because the replication
helper just stopped half-way.
So, even though yes, FDB events on LAG bridge ports must be
special-cased, in the end it's simpler to let switchdev_handle_fdb_*
just iterate through the LAG port's switchdev lowers, and let the
switchdev driver figure out that those physical ports are under a LAG.
The switchdev_handle_fdb_event_to_device() helper takes a
"foreign_dev_check" callback so it can figure out whether @dev can
autonomously forward to @foreign_dev. DSA fills this method properly:
if the LAG is offloaded by another port in the same tree as @dev, then
it isn't foreign. If it is a software LAG, it is foreign - forwarding
happens in software.
Whether an interface is foreign or not decides whether the replication
helper will go through the LAG's switchdev lowers or not. Since the
lan966x doesn't properly fill this out, FDB events on software LAG
uppers will get called. By changing lan966x_foreign_dev_check(), we can
suppress them.
Whereas DSA will now start receiving FDB events for its offloaded LAG
uppers, so we need to return -EOPNOTSUPP, since we currently don't do
the right thing for them.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The main purpose of this change is to create a data structure for a LAG
as seen by DSA. This is similar to what we have for bridging - we pass a
copy of this structure by value to ->port_lag_join and ->port_lag_leave.
For now we keep the lag_dev, id and a reference count in it. Future
patches will add a list of FDB entries for the LAG (these also need to
be refcounted to work properly).
The LAG structure is created using dsa_port_lag_create() and destroyed
using dsa_port_lag_destroy(), just like we have for bridging.
Because now, the dsa_lag itself is refcounted, we can simplify
dsa_lag_map() and dsa_lag_unmap(). These functions need to keep a LAG in
the dst->lags array only as long as at least one port uses it. The
refcounting logic inside those functions can be removed now - they are
called only when we should perform the operation.
dsa_lag_dev() is renamed to dsa_lag_by_id() and now returns the dsa_lag
structure instead of the lag_dev net_device.
dsa_lag_foreach_port() now takes the dsa_lag structure as argument.
dst->lags holds an array of dsa_lag structures.
dsa_lag_map() now also saves the dsa_lag->id value, so that linear
walking of dst->lags in drivers using dsa_lag_id() is no longer
necessary. They can just look at lag.id.
dsa_port_lag_id_get() is a helper, similar to dsa_port_bridge_num_get(),
which can be used by drivers to get the LAG ID assigned by DSA to a
given port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DSA LAG API will be changed to become more similar with the bridge
data structures, where struct dsa_bridge holds an unsigned int num,
which is generated by DSA and is one-based. We have a similar thing
going with the DSA LAG, except that isn't stored anywhere, it is
calculated dynamically by dsa_lag_id() by iterating through dst->lags.
The idea of encoding an invalid (or not requested) LAG ID as zero for
the purpose of simplifying checks in drivers means that the LAG IDs
passed by DSA to drivers need to be one-based too. So back-and-forth
conversion is needed when indexing the dst->lags array, as well as in
drivers which assume a zero-based index.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of converting struct net_device *dp->lag_dev into a
struct dsa_lag *dp->lag, we need to rename, for consistency purposes,
all occurrences of the "lag" variable in the DSA core to "lag_dev".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using hci_le_create_conn_sync it shall wait for the conn_timeout
since the connection complete may take longer than just 2 seconds.
Also fix the masking of HCI_EV_LE_ENHANCED_CONN_COMPLETE and
HCI_EV_LE_CONN_COMPLETE so they are never both set so we can predict
which one the controller will use in case of HCI_OP_LE_CREATE_CONN.
Fixes: 6cd29ec6ae ("Bluetooth: hci_sync: Wait for proper events when connecting LE")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_update_accept_list_sync is returning the filter based on the error
but that gets overwritten by hci_le_set_addr_resolution_enable_sync
return instead of using the actual result of the likes of
hci_le_add_accept_list_sync which was intended.
Fixes: ad383c2c65 ("Bluetooth: hci_sync: Enable advertising when LL privacy is enabled")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Previous commit e04480920d ("Bluetooth: defer cleanup of resources
in hci_unregister_dev()") defers all destructive actions to
hci_release_dev() to prevent cocurrent problems like NPD, UAF.
However, there are still some exceptions that are ignored.
The smp_unregister() in hci_dev_close_sync() (previously in
hci_dev_do_close) will release resources like the sensitive channel
and the smp_dev objects. Consider the situations the device is detaching
or power down while the kernel is still operating on it, the following
data race could take place.
thread-A hci_dev_close_sync | thread-B read_local_oob_ext_data
|
hci_dev_unlock() |
... | hci_dev_lock()
if (hdev->smp_data) |
chan = hdev->smp_data |
| chan = hdev->smp_data (3)
|
hdev->smp_data = NULL (1) | if (!chan || !chan->data) (4)
... |
smp = chan->data | smp = chan->data
if (smp) |
chan->data = NULL (2) |
... |
kfree_sensitive(smp) |
| // dereference smp trigger UFA
That is, the objects hdev->smp_data and chan->data both suffer from the
data races. In a preempt-enable kernel, the above schedule (when (3) is
before (1) and (4) is before (2)) leads to UAF bugs. It can be
reproduced in the latest kernel and below is part of the report:
[ 49.097146] ================================================================
[ 49.097611] BUG: KASAN: use-after-free in smp_generate_oob+0x2dd/0x570
[ 49.097611] Read of size 8 at addr ffff888006528360 by task generate_oob/155
[ 49.097611]
[ 49.097611] Call Trace:
[ 49.097611] <TASK>
[ 49.097611] dump_stack_lvl+0x34/0x44
[ 49.097611] print_address_description.constprop.0+0x1f/0x150
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] kasan_report.cold+0x7f/0x11b
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] smp_generate_oob+0x2dd/0x570
[ 49.097611] read_local_oob_ext_data+0x689/0xc30
[ 49.097611] ? hci_event_packet+0xc80/0xc80
[ 49.097611] ? sysvec_apic_timer_interrupt+0x9b/0xc0
[ 49.097611] ? asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 49.097611] ? mgmt_init_hdev+0x1c/0x240
[ 49.097611] ? mgmt_init_hdev+0x28/0x240
[ 49.097611] hci_sock_sendmsg+0x1880/0x1e70
[ 49.097611] ? create_monitor_event+0x890/0x890
[ 49.097611] ? create_monitor_event+0x890/0x890
[ 49.097611] sock_sendmsg+0xdf/0x110
[ 49.097611] __sys_sendto+0x19e/0x270
[ 49.097611] ? __ia32_sys_getpeername+0xa0/0xa0
[ 49.097611] ? kernel_fpu_begin_mask+0x1c0/0x1c0
[ 49.097611] __x64_sys_sendto+0xd8/0x1b0
[ 49.097611] ? syscall_exit_to_user_mode+0x1d/0x40
[ 49.097611] do_syscall_64+0x3b/0x90
[ 49.097611] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 49.097611] RIP: 0033:0x7f5a59f51f64
...
[ 49.097611] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f5a59f51f64
[ 49.097611] RDX: 0000000000000007 RSI: 00007f5a59d6ac70 RDI: 0000000000000006
[ 49.097611] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[ 49.097611] R10: 0000000000000040 R11: 0000000000000246 R12: 00007ffec26916ee
[ 49.097611] R13: 00007ffec26916ef R14: 00007f5a59d6afc0 R15: 00007f5a59d6b700
To solve these data races, this patch places the smp_unregister()
function in the protected area by the hci_dev_lock(). That is, the
smp_unregister() function can not be concurrently executed when
operating functions (most of them are mgmt operations in mgmt.c) hold
the device lock.
This patch is tested with kernel LOCK DEBUGGING enabled. The price from
the extended holding time of the device lock is supposed to be low as the
smp_unregister() function is fairly short and efficient.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
sent_cmd memory is not freed before freeing hci_dev causing it to leak
it contents.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As Jakub noticed, prints should be avoided on the datapath.
Also, as packets would never come to the else branch in
ping_lookup(), remove pr_err() from ping_lookup().
Fixes: 35a79e64de ("ping: fix the dif and sdif check in ping_lookup")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/1ef3f2fcd31bd681a193b1fcf235eee1603819bd.1645674068.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
valid_lft, prefered_lft and tstamp are always accessed under the lock
"lock" in other places. Reading these without taking the lock may result
in inconsistencies regarding the calculation of the valid and preferred
variables since decisions are taken on these fields for those variables.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Niels Dossche <niels.dossche@ugent.be>
Link: https://lore.kernel.org/r/20220223131954.6570-1-niels.dossche@ugent.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
smc_pnetid_by_table_ib() uses read_lock() and then it calls smc_pnet_apply_ib()
which, in turn, calls mutex_lock(&smc_ib_devices.mutex).
read_lock() disables preemption. Therefore, the code acquires a mutex while in
atomic context and it leads to a SAC bug.
Fix this bug by replacing the rwlock with a mutex.
Reported-and-tested-by: syzbot+4f322a6d84e991c38775@syzkaller.appspotmail.com
Fixes: 64e28b52c7 ("net/smc: add pnet table namespace support")
Confirmed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20220223100252.22562-1-fmdefrancesco@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit fb8696ab14 ("can: gw: synchronize rcu operations
before removing gw job entry") added three synchronize_rcu() calls
to make sure one rcu grace period was observed before freeing
a "struct cgw_job" (which are tiny objects).
This should be converted to call_rcu() to avoid adding delays
in device / network dismantles.
Use the rcu_head that was already in struct cgw_job,
not yet used.
Link: https://lore.kernel.org/all/20220207190706.1499190-1-eric.dumazet@gmail.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
I missed the obvious case where netif_ix() is invoked from hard-IRQ
context.
Disabling bottom halves is only needed in process context. This ensures
that the code remains on the current CPU and that the soft-interrupts
are processed at local_bh_enable() time.
In hard- and soft-interrupt context this is already the case and the
soft-interrupts will be processed once the context is left (at irq-exit
time).
Disable bottom halves if neither hard-interrupts nor soft-interrupts are
disabled. Update the kernel-doc, mention that interrupts must be enabled
if invoked from process context.
Fixes: baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/Yg05duINKBqvnxUc@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensures that the DSA switch driver gets notified of changes to the
BR_PORT_LOCKED flag as well, for the case when a DSA port joins or
leaves a LAG that is a bridge port.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various switchcores support setting ports in locked mode, so that
clients behind locked ports cannot send traffic through the port
unless a fdb entry is added with the clients MAC address.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a 802.1X scenario, clients connected to a bridge port shall not
be allowed to have traffic forwarded until fully authenticated.
A static fdb entry of the clients MAC address for the bridge port
unlocks the client and allows bidirectional communication.
This scenario is facilitated with setting the bridge port in locked
mode, which is also supported by various switchcore chipsets.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following coccicheck warning:
./net/sched/act_api.c:277:7-49: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drop_monitor is using an unique list on which all netdevices in
the host have an element, regardless of their netns.
This scales poorly, not only at device unregister time (what I
caught during my netns dismantle stress tests), but also at packet
processing time whenever trace_napi_poll_hit() is called.
If the intent was to avoid adding one pointer in 'struct net_device'
then surely we prefer O(1) behavior.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These tests are supposed to check if the loop exited via a break or not.
However the tests are wrong because if we did not exit via a break then
"p" is not a valid pointer. In that case, it's the equivalent of
"if (*(u32 *)sr == *last_key) {". That's going to work most of the time,
but there is a potential for those to be equal.
Fixes: 1593123a6a ("tipc: add name table dump to new netlink api")
Fixes: 1a1a143daf ("tipc: add publication dump to new netlink api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test is checking if we exited the list via break or not. However
if it did not exit via a break then "node" does not point to a valid
udp_tunnel_nic_shared_node struct. It will work because of the way
the structs are laid out it's the equivalent of
"if (info->shared->udp_tunnel_nic_info != dev)" which will always be
true, but it's not the right way to test.
Fixes: 74cc6d182d ("udp_tunnel: add the ability to share port tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mctp/device.c:140:11: warning: Assigned value is garbage or undefined
[clang-analyzer-core.uninitialized.Assign]
mcb->idx = idx;
- Not a real problem due to how the callback runs, fix the warning.
net/mctp/route.c:458:4: warning: Value stored to 'msk' is never read
[clang-analyzer-deadcode.DeadStores]
msk = container_of(key->sk, struct mctp_sock, sk);
- 'msk' dead assignment can be removed here.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the extended addressing local route output codepath
dev_get_by_index_rcu() doesn't take a dev_hold() so we shouldn't
dev_put().
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously there was a race that could allow the mctp_dev refcount
to hit zero:
rcu_read_lock();
mdev = __mctp_dev_get(dev);
// mctp_unregister() happens here, mdev->refs hits zero
mctp_dev_hold(dev);
rcu_read_unlock();
Now we make __mctp_dev_get() take the hold itself. It is safe to test
against the zero refcount because __mctp_dev_get() is called holding
rcu_read_lock and mctp_dev uses kfree_rcu().
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic from switchdev_handle_port_obj_add_foreign() is directly
adapted from switchdev_handle_fdb_event_to_device(), which already
detects events on foreign interfaces and reoffloads them towards the
switchdev neighbors.
However, when we have a simple br0 <-> bond0 <-> swp0 topology and the
switchdev_handle_port_obj_add_foreign() gets called on bond0, we get
stuck into an infinite recursion:
1. bond0 does not pass check_cb(), so we attempt to find switchdev
neighbor interfaces. For that, we recursively call
__switchdev_handle_port_obj_add() for bond0's bridge, br0.
2. __switchdev_handle_port_obj_add() recurses through br0's lowers,
essentially calling __switchdev_handle_port_obj_add() for bond0
3. Go to step 1.
This happens because switchdev_handle_fdb_event_to_device() and
switchdev_handle_port_obj_add_foreign() are not exactly the same.
The FDB event helper special-cases LAG interfaces with its lag_mod_cb(),
so this is why we don't end up in an infinite loop - because it doesn't
attempt to treat LAG interfaces as potentially foreign bridge ports.
The problem is solved by looking ahead through the bridge's lowers to
see whether there is any switchdev interface that is foreign to the @dev
we are currently processing. This stops the recursion described above at
step 1: __switchdev_handle_port_obj_add(bond0) will not create another
call to __switchdev_handle_port_obj_add(br0). Going one step upper
should only happen when we're starting from a bridge port that has been
determined to be "foreign" to the switchdev driver that passes the
foreign_dev_check_cb().
Fixes: c4076cdd21 ("net: switchdev: introduce switchdev_handle_port_obj_{add,del} for foreign interfaces")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While kfree_rcu(ptr) _is_ supported, it has some limitations.
Given that 99.99% of kfree_rcu() users [1] use the legacy
two parameters variant, and @catchall objects do have an rcu head,
simply use it.
Choice of kfree_rcu(ptr) variant was probably not intentional.
[1] including calls from net/netfilter/nf_tables_api.c
Fixes: aaa31047a6 ("netfilter: nftables: add catch-all set element support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
syzbot found another way to trigger the infamous WARN_ON_ONCE(delta < len)
in skb_try_coalesce() [1]
I was able to root cause the issue to kfence.
When kfence is in action, the following assertion is no longer true:
int size = xxxx;
void *ptr1 = kmalloc(size, gfp);
void *ptr2 = kmalloc(size, gfp);
if (ptr1 && ptr2)
ASSERT(ksize(ptr1) == ksize(ptr2));
We attempted to fix these issues in the blamed commits, but forgot
that TCP was possibly shifting data after skb_unclone_keeptruesize()
has been used, notably from tcp_retrans_try_collapse().
So we not only need to keep same skb->truesize value,
we also need to make sure TCP wont fill new tailroom
that pskb_expand_head() was able to get from a
addr = kmalloc(...) followed by ksize(addr)
Split skb_unclone_keeptruesize() into two parts:
1) Inline skb_unclone_keeptruesize() for the common case,
when skb is not cloned.
2) Out of line __skb_unclone_keeptruesize() for the 'slow path'.
WARNING: CPU: 1 PID: 6490 at net/core/skbuff.c:5295 skb_try_coalesce+0x1235/0x1560 net/core/skbuff.c:5295
Modules linked in:
CPU: 1 PID: 6490 Comm: syz-executor161 Not tainted 5.17.0-rc4-syzkaller-00229-g4f12b742eb2b #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:skb_try_coalesce+0x1235/0x1560 net/core/skbuff.c:5295
Code: bf 01 00 00 00 0f b7 c0 89 c6 89 44 24 20 e8 62 24 4e fa 8b 44 24 20 83 e8 01 0f 85 e5 f0 ff ff e9 87 f4 ff ff e8 cb 20 4e fa <0f> 0b e9 06 f9 ff ff e8 af b2 95 fa e9 69 f0 ff ff e8 95 b2 95 fa
RSP: 0018:ffffc900063af268 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 00000000ffffffd5 RCX: 0000000000000000
RDX: ffff88806fc05700 RSI: ffffffff872abd55 RDI: 0000000000000003
RBP: ffff88806e675500 R08: 00000000ffffffd5 R09: 0000000000000000
R10: ffffffff872ab659 R11: 0000000000000000 R12: ffff88806dd554e8
R13: ffff88806dd9bac0 R14: ffff88806dd9a2c0 R15: 0000000000000155
FS: 00007f18014f9700(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020002000 CR3: 000000006be7a000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
tcp_try_coalesce net/ipv4/tcp_input.c:4651 [inline]
tcp_try_coalesce+0x393/0x920 net/ipv4/tcp_input.c:4630
tcp_queue_rcv+0x8a/0x6e0 net/ipv4/tcp_input.c:4914
tcp_data_queue+0x11fd/0x4bb0 net/ipv4/tcp_input.c:5025
tcp_rcv_established+0x81e/0x1ff0 net/ipv4/tcp_input.c:5947
tcp_v4_do_rcv+0x65e/0x980 net/ipv4/tcp_ipv4.c:1719
sk_backlog_rcv include/net/sock.h:1037 [inline]
__release_sock+0x134/0x3b0 net/core/sock.c:2779
release_sock+0x54/0x1b0 net/core/sock.c:3311
sk_wait_data+0x177/0x450 net/core/sock.c:2821
tcp_recvmsg_locked+0xe28/0x1fd0 net/ipv4/tcp.c:2457
tcp_recvmsg+0x137/0x610 net/ipv4/tcp.c:2572
inet_recvmsg+0x11b/0x5e0 net/ipv4/af_inet.c:850
sock_recvmsg_nosec net/socket.c:948 [inline]
sock_recvmsg net/socket.c:966 [inline]
sock_recvmsg net/socket.c:962 [inline]
____sys_recvmsg+0x2c4/0x600 net/socket.c:2632
___sys_recvmsg+0x127/0x200 net/socket.c:2674
__sys_recvmsg+0xe2/0x1a0 net/socket.c:2704
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: c4777efa75 ("net: add and use skb_unclone_keeptruesize() helper")
Fixes: 097b9146c0 ("net: fix up truesize of cloned skb in skb_prepare_for_shift()")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Marco Elver <elver@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have multiple places where this helper is convenient,
and plan using it in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All other skbs allocated for TCP tx are using MAX_TCP_HEADER already.
MAX_HEADER can be too small for some cases (like eBPF based encapsulation),
so this can avoid extra pskb_expand_head() in lower stacks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220222031115.4005060-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a bridged port is not offloaded to the hardware - either because the
underlying driver does not implement the port_bridge_{join,leave} ops,
or because the operation failed - then its dp->bridge pointer will be
NULL when dsa_port_bridge_leave() is called. Avoid dereferncing NULL.
This fixes the following splat when removing a port from a bridge:
Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT_RT SMP
CPU: 3 PID: 1119 Comm: brctl Tainted: G O 5.17.0-rc4-rt4 #1
Call trace:
dsa_port_bridge_leave+0x8c/0x1e4
dsa_slave_changeupper+0x40/0x170
dsa_slave_netdevice_event+0x494/0x4d4
notifier_call_chain+0x80/0xe0
raw_notifier_call_chain+0x1c/0x24
call_netdevice_notifiers_info+0x5c/0xac
__netdev_upper_dev_unlink+0xa4/0x200
netdev_upper_dev_unlink+0x38/0x60
del_nbp+0x1b0/0x300
br_del_if+0x38/0x114
add_del_if+0x60/0xa0
br_ioctl_stub+0x128/0x2dc
br_ioctl_call+0x68/0xb0
dev_ifsioc+0x390/0x554
dev_ioctl+0x128/0x400
sock_do_ioctl+0xb4/0xf4
sock_ioctl+0x12c/0x4e0
__arm64_sys_ioctl+0xa8/0xf0
invoke_syscall+0x4c/0x110
el0_svc_common.constprop.0+0x48/0xf0
do_el0_svc+0x28/0x84
el0_svc+0x1c/0x50
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x17c/0x180
Code: f9402f00 f0002261 f9401302 913cc021 (a9401404)
---[ end trace 0000000000000000 ]---
Fixes: d3eed0e57d ("net: dsa: keep the bridge_dev and bridge_num as part of the same structure")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220221203539.310690-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean reports that probing on DSA drivers that aren't yet
populating supported_interfaces now fails. Fix this by allowing
phylink to detect whether DSA actually provides an underlying
mac_select_pcs() implementation.
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Fixes: bde018222c ("net: dsa: add support for phylink mac_select_pcs()")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1nMCD6-00A0wC-FG@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever one of these functions pull all data from an skb in a frag_list,
use consume_skb() instead of kfree_skb() to avoid polluting drop
monitoring.
Fixes: 6fa01ccd88 ("skbuff: Add pskb_extract() helper function")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220220154052.1308469-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix virtual vs physical address confusion (which currently are the same).
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Another thing making netns dismantles potentially very slow is located
in gro_cells_destroy(),
whenever cleanup_net() has to remove a device using gro_cells framework.
RTNL is not held at this stage, so synchronize_net()
is calling synchronize_rcu():
netdev_run_todo()
ip_tunnel_dev_free()
gro_cells_destroy()
synchronize_net()
synchronize_rcu() // Ouch.
This patch uses call_rcu(), and gave me a 25x performance improvement
in my tests.
cleanup_net() is no longer blocked ~10 ms per synchronize_rcu()
call.
In the case we could not allocate the memory needed to queue the
deferred free, use synchronize_rcu_expedited()
v2: made percpu_free_defer_callback() static
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220220041155.607637-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is fixing up the use without proper initialization in patch 5/5
-o-
Hi,
The following patchset contains Netfilter fixes for net:
1) Missing #ifdef CONFIG_IP6_NF_IPTABLES in recent xt_socket fix.
2) Fix incorrect flow action array size in nf_tables.
3) Unregister flowtable hooks from netns exit path.
4) Fix missing limit object release, from Florian Westphal.
5) Memleak in nf_tables object update path, also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
stateful objects can be updated from the control plane.
The transaction logic allocates a temporary object for this purpose.
The ->init function was called for this object, so plain kfree() leaks
resources. We must call ->destroy function of the object.
nft_obj_destroy does this, but it also decrements the module refcount,
but the update path doesn't increment it.
To avoid special-casing the update object release, do module_get for
the update case too and release it via nft_obj_destroy().
Fixes: d62d0ba97b ("netfilter: nf_tables: Introduce stateful object update operation")
Cc: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In hsr, lockdep_is_held() is needed for rcu_dereference_bh_check().
But if lockdep is not enabled, lockdep_is_held() causes a build error:
ERROR: modpost: "lockdep_is_held" [net/hsr/hsr.ko] undefined!
Thus, this patch solved by adding lockdep_hsr_is_held(). This helper
function calls the lockdep_is_held() when lockdep is enabled, and returns 1
if not defined.
Fixes: e7f2742068 ("net: hsr: fix suspicious RCU usage warning in hsr_node_get_first()")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Link: https://lore.kernel.org/r/20220220153250.5285-1-claudiajkang@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to provide a destroy callback to release the extra fields.
Fixes: 3b9e2ea6c1 ("netfilter: nft_limit: move stateful fields out of expression data")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Unregister flowtable hooks before they are releases via
nf_tables_flowtable_destroy() otherwise hook core reports UAF.
BUG: KASAN: use-after-free in nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
Read of size 4 at addr ffff8880736f7438 by task syz-executor579/3666
CPU: 0 PID: 3666 Comm: syz-executor579 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
__dump_stack lib/dump_stack.c:88 [inline] lib/dump_stack.c:106
dump_stack_lvl+0x1dc/0x2d8 lib/dump_stack.c:106 lib/dump_stack.c:106
print_address_description+0x65/0x380 mm/kasan/report.c:247 mm/kasan/report.c:247
__kasan_report mm/kasan/report.c:433 [inline]
__kasan_report mm/kasan/report.c:433 [inline] mm/kasan/report.c:450
kasan_report+0x19a/0x1f0 mm/kasan/report.c:450 mm/kasan/report.c:450
nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
__nf_register_net_hook+0x27e/0x8d0 net/netfilter/core.c:429 net/netfilter/core.c:429
nf_register_net_hook+0xaa/0x180 net/netfilter/core.c:571 net/netfilter/core.c:571
nft_register_flowtable_net_hooks+0x3c5/0x730 net/netfilter/nf_tables_api.c:7232 net/netfilter/nf_tables_api.c:7232
nf_tables_newflowtable+0x2022/0x2cf0 net/netfilter/nf_tables_api.c:7430 net/netfilter/nf_tables_api.c:7430
nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline]
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline]
nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline] net/netfilter/nfnetlink.c:652
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline] net/netfilter/nfnetlink.c:652
nfnetlink_rcv+0x10e6/0x2550 net/netfilter/nfnetlink.c:652 net/netfilter/nfnetlink.c:652
__nft_release_hook() calls nft_unregister_flowtable_net_hooks() which
only unregisters the hooks, then after RCU grace period, it is
guaranteed that no packets add new entries to the flowtable (no flow
offload rules and flowtable hooks are reachable from packet path), so it
is safe to call nf_flow_table_free() which cleans up the remaining
entries from the flowtable (both software and hardware) and it unbinds
the flow_block.
Fixes: ff4bf2f42a ("netfilter: nf_tables: add nft_unregister_flowtable_hook()")
Reported-by: syzbot+e918523f77e62790d6d9@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch separate NS message allocation steps from ndisc_send_ns(),
so it could be used in other places, like bonding, to allocate and
send IPv6 NS message.
Also export ndisc_send_skb() and ndisc_ns_create() for later bonding usage.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case user space sends a packet destined to a broadcast address when a
matching broadcast route is not configured, the kernel will create a
unicast neighbour entry that will never be resolved [1].
When the broadcast route is configured, the unicast neighbour entry will
not be invalidated and continue to linger, resulting in packets being
dropped.
Solve this by invalidating unresolved neighbour entries for broadcast
addresses after routes for these addresses are internally configured by
the kernel. This allows the kernel to create a broadcast neighbour entry
following the next route lookup.
Another possible solution that is more generic but also more complex is
to have the ARP code register a listener to the FIB notification chain
and invalidate matching neighbour entries upon the addition of broadcast
routes.
It is also possible to wave off the issue as a user space problem, but
it seems a bit excessive to expect user space to be that intimately
familiar with the inner workings of the FIB/neighbour kernel code.
[1] https://lore.kernel.org/netdev/55a04a8f-56f3-f73c-2aea-2195923f09d1@huawei.com/
Reported-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
-> ipip encap -> net_failover tx -> virtio_net tx
When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.
Call Trace:
tcp4_gso_segment ------> return NULL
inet_gso_segment ------> inner iph, network_header points to
ipip_gso_segment
inet_gso_segment ------> outer iph
skb_mac_gso_segment
Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.
Call Trace:
inet_gso_segment ------> inner iph, outer iph is skipped
skb_mac_gso_segment
__skb_gso_segment
validate_xmit_skb
validate_xmit_skb_list
sch_direct_xmit
__qdisc_run
__dev_queue_xmit ------> virtio_net
dev_hard_start_xmit
__dev_queue_xmit ------> net_failover
ip_finish_output2
ip_output
iptunnel_xmit
ip_tunnel_xmit
ipip_tunnel_xmit ------> ipip
dev_hard_start_xmit
__dev_queue_xmit
ip_finish_output2
ip_output
ip_forward
ip_rcv
__netif_receive_skb_one_core
netif_receive_skb_internal
napi_gro_receive
receive_buf
virtnet_poll
net_rx_action
The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.
This patch also includes ipv6_gso_segment(), considering SIT, etc.
Fixes: cb32f511a7 ("ipip: add GSO/TSO support")
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Open coded calculation can be avoided and replaced by the
equivalent csum_replace_by_diff() and csum_sub().
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmISrYgeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGg20IAKDZr7rfSHBopjQV
Cocw744tom0XuxpvSZpp2GGOOXF+tkswcNNaRIrbGOl1mkyxA7eBZCTMpDeDS9aQ
wB0D0Gxx8QBAJp4KgB1W7TB+hIGes/rs8Ve+6iO4ulLLdCVWX/q2boI0aZ7QX9O9
qNi8OsoZQtk6falRvciZFHwV5Av1p2Sy1AW57udQ7DvJ4H98AfKf1u8/z208WWW8
1ixC+qJxQcUcM9vI+7P9Tt7NbFSKv8SvAmqjFY7P+DxQAsVw6KXoqVXykDzeOv0t
fUNOE/t0oFZafwtn8h7KBQnwS9lH03+3KkslVZs+iMFyUj/Bar+NVVyKoDhWXtVg
/PuMhEg=
=eU1o
-----END PGP SIGNATURE-----
Merge tag 'v5.17-rc5' into sched/core, to resolve conflicts
New conflicts in sched/core due to the following upstream fixes:
44585f7bc0 ("psi: fix "defined but not used" warnings when CONFIG_PROC_FS=n")
a06247c680 ("psi: Fix uaf issue when psi trigger is destroyed while being polled")
Conflicts:
include/linux/psi_types.h
kernel/sched/psi.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Replace tcp_drop() used in tcp_data_queue_ofo with tcp_drop_reason().
Following drop reasons are introduced:
SKB_DROP_REASON_TCP_OFOMERGE
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace tcp_drop() used in tcp_data_queue() with tcp_drop_reason().
Following drop reasons are introduced:
SKB_DROP_REASON_TCP_ZEROWINDOW
SKB_DROP_REASON_TCP_OLD_DATA
SKB_DROP_REASON_TCP_OVERWINDOW
SKB_DROP_REASON_TCP_OLD_DATA is used for the case that end_seq of skb
less than the left edges of receive window. (Maybe there is a better
name?)
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace tcp_drop() used in tcp_rcv_established() with tcp_drop_reason().
Following drop reasons are added:
SKB_DROP_REASON_TCP_FLAGS
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() used in tcp_v4_do_rcv() and tcp_v6_do_rcv() with
kfree_skb_reason().
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the address of drop_reason to tcp_add_backlog() to store the
reasons for skb drops when fails. Following drop reasons are
introduced:
SKB_DROP_REASON_SOCKET_BACKLOG
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the address of drop reason to tcp_v4_inbound_md5_hash() and
tcp_v6_inbound_md5_hash() to store the reasons for skb drops when this
function fails. Therefore, the drop reason can be passed to
kfree_skb_reason() when the skb needs to be freed.
Following drop reasons are added:
SKB_DROP_REASON_TCP_MD5NOTFOUND
SKB_DROP_REASON_TCP_MD5UNEXPECTED
SKB_DROP_REASON_TCP_MD5FAILURE
SKB_DROP_REASON_TCP_MD5* above correspond to LINUX_MIB_TCPMD5*
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() used in tcp_v6_rcv() with kfree_skb_reason().
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kfree_skb_reason() for some path in tcp_v4_rcv() that missed before,
including:
SKB_DROP_REASON_SOCKET_FILTER
SKB_DROP_REASON_XFRM_POLICY
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TCP protocol, tcp_drop() is used to free the skb when it needs
to be dropped. To make use of kfree_skb_reason() and pass the drop
reason to it, introduce the function tcp_drop_reason(). Meanwhile,
make tcp_drop() an inline call to tcp_drop_reason().
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
immediate verdict expression needs to allocate one slot in the flow offload
action array, however, immediate data expression does not need to do so.
fwd and dup expression need to allocate one slot, this is missing.
Add a new offload_action interface to report if this expression needs to
allocate one slot in the flow offload action array.
Fixes: be2861dc36 ("netfilter: nft_{fwd,dup}_netdev: add offload support")
Reported-and-tested-by: Nick Gregory <Nick.Gregory@Sophos.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the DSA master doesn't support IFF_UNICAST_FLT, then the following
call path is possible:
dsa_slave_switchdev_event_work
-> dsa_port_host_fdb_add
-> dev_uc_add
-> __dev_set_rx_mode
-> __dev_set_promiscuity
Since the blamed commit, dsa_slave_switchdev_event_work() no longer
holds rtnl_lock(), which triggers the ASSERT_RTNL() from
__dev_set_promiscuity().
Taking rtnl_lock() around dev_uc_add() is impossible, because all the
code paths that call dsa_flush_workqueue() do so from contexts where the
rtnl_mutex is already held - so this would lead to an instant deadlock.
dev_uc_add() in itself doesn't require the rtnl_mutex for protection.
There is this comment in __dev_set_rx_mode() which assumes so:
/* Unicast addresses changes may only happen under the rtnl,
* therefore calling __dev_set_promiscuity here is safe.
*/
but it is from commit 4417da668c ("[NET]: dev: secondary unicast
address support") dated June 2007, and in the meantime, commit
f1f28aa351 ("netdev: Add addr_list_lock to struct net_device."), dated
July 2008, has added &dev->addr_list_lock to protect this instead of the
global rtnl_mutex.
Nonetheless, __dev_set_promiscuity() does assume rtnl_mutex protection,
but it is the uncommon path of what we typically expect dev_uc_add()
to do. So since only the uncommon path requires rtnl_lock(), just check
ahead of time whether dev_uc_add() would result into a call to
__dev_set_promiscuity(), and handle that condition separately.
DSA already configures the master interface to be promiscuous if the
tagger requires this. We can extend this to also cover the case where
the master doesn't handle dev_uc_add() (doesn't support IFF_UNICAST_FLT),
and on the premise that we'd end up making it promiscuous during
operation anyway, either if a DSA slave has a non-inherited MAC address,
or if the bridge notifies local FDB entries for its own MAC address, the
address of a station learned on a foreign port, etc.
Fixes: 0faf890fc5 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two error paths need to release_sock(sk) before returning.
Fixes: a6a6fe27ba ("net/smc: Dynamic control handshake limitation by socket options")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With drivers converted over to using phylink PCS, there is no need for
the struct dsa_switch member "pcs_poll" to exist anymore - there is a
flag in the struct phylink_pcs which indicates whether this PCS needs
to be polled which supersedes this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent patches, and in particular commits
faab39f63c ("net: allow out-of-order netdev unregistration") and
e5f80fcf86 ("ipv6: give an IPv6 dev to blackhole_netdev")
we no longer need the barrier implemented in rtnl_lock_unregistering().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cleanup_net() is competing with other rtnl users.
Instead of calling br_net_exit() for each netns,
call br_net_exit_batch() once.
This gives cleanup_net() ability to group more devices
and call unregister_netdevice_many() only once for all bridge devices.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for MRT6MSG_WRMIFWHOLE which is used to pass
full packet and real vif id when the incoming interface is wrong.
While the RP and FHR are setting up state we need to be sending the
registers encapsulated with all the data inside otherwise we lose it.
The RP then decapsulates it and forwards it to the interested parties.
Currently with WRONGMIF we can only be sending empty register packets
and will lose that data.
This behaviour can be enabled by using MRT_PIM with
val == MRT6MSG_WRMIFWHOLE. This doesn't prevent MRT6MSG_WRONGMIF from
happening, it happens in addition to it, also it is controlled by the same
throttling parameters as WRONGMIF (i.e. 1 packet per 3 seconds currently).
Both messages are generated to keep backwards compatibily and avoid
breaking someone who was enabling MRT_PIM with val == 4, since any
positive val is accepted and treated the same.
Signed-off-by: Mobashshera Rasool <mobash.rasool.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP in kernel path manager has some constraints on incoming
addresses announce processing, so that in edge scenarios it can
end-up dropping (ignoring) some of such announces.
The above is not very limiting in practice since such scenarios are
very uncommon and MPTCP will recover due to ADD_ADDR retransmissions.
This patch adds a few MIB counters to account for such drop events
to allow easier introspection of the critical scenarios.
Fixes: f7efc7771e ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an MPTCP endpoint received multiple consecutive incoming
ADD_ADDR options, mptcp_pm_add_addr_received() can overwrite
the current remote address value after the PM lock is released
in mptcp_pm_nl_add_addr_received() and before such address
is echoed.
Fix the issue caching the remote address value a little earlier
and always using the cached value after releasing the PM lock.
Fixes: f7efc7771e ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit a88c9e4969 ("mptcp: do not block subflows
creation on errors"), if a signal address races with a failing
subflow creation, the subflow creation failure control path
can trigger the selection of the next address to be announced
while the current announced is still pending.
The above will cause the unintended suppression of the ADD_ADDR
announce.
Fix the issue skipping the to-be-suppressed announce before it
will mark an endpoint as already used. The relevant announce
will be triggered again when the current one will complete.
Fixes: a88c9e4969 ("mptcp: do not block subflows creation on errors")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds some basic sanity checks for the source and dest
headers of packets on initial receive.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, we have mctp_address_ok(), which checks if an EID is in the
"valid" range of 8-254 inclusive. However, 0 and 255 may also be valid
addresses, depending on context. 0 is the NULL EID, which may be set
when physical addressing is used. 255 is valid as a destination address
for broadcasts.
This change renames mctp_address_ok to mctp_address_unicast, and adds
similar helpers for broadcast and null EIDs, which will be used in an
upcoming commit.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds a new protocol attribute to IPv4 and IPv6 addresses.
Inspiration was taken from the protocol attribute of routes. User space
applications like iproute2 can set/get the protocol with the Netlink API.
The attribute is stored as an 8-bit unsigned integer.
The protocol attribute is set by kernel for these categories:
- IPv4 and IPv6 loopback addresses
- IPv6 addresses generated from router announcements
- IPv6 link local addresses
User space may pass custom protocols, not defined by the kernel.
Grouping addresses on their origin is useful in scenarios where you want
to distinguish between addresses based on who added them, e.g. kernel
vs. user space.
Tagging addresses with a string label is an existing feature that could be
used as a solution. Unfortunately the max length of a label is
15 characters, and for compatibility reasons the label must be prefixed
with the name of the device followed by a colon. Since device names also
have a max length of 15 characters, only -1 characters is guaranteed to be
available for any origin tag, which is not that much.
A reference implementation of user space setting and getting protocols
is available for iproute2:
9a6ea18bd7
Signed-off-by: Jacques de Laval <Jacques.De.Laval@westermo.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220217150202.80802-1-Jacques.De.Laval@westermo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the list of devices has N elements, netdev_wait_allrefs_any()
is called N times, and linkwatch_forget_dev() is called N*(N-1)/2 times.
Fix this by calling linkwatch_forget_dev() only once per device.
Fixes: faab39f63c ("net: allow out-of-order netdev unregistration")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220218065430.2613262-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPv6 has this hack changing sk->sk_prot when an IPv6 socket
is 'converted' to an IPv4 one with IPV6_ADDRFORM option.
This operation is only performed for TCP and UDP, knowing
their 'struct proto' for the two network families are populated
in the same way, and can not disappear while a reader
might use and dereference sk->sk_prot.
If we think about it all reads of sk->sk_prot while
either socket lock or RTNL is not acquired should be using READ_ONCE().
Also note that other layers like MPTCP, XFRM, CHELSIO_TLS also
write over sk->sk_prot.
BUG: KCSAN: data-race in inet6_recvmsg / ipv6_setsockopt
write to 0xffff8881386f7aa8 of 8 bytes by task 26932 on cpu 0:
do_ipv6_setsockopt net/ipv6/ipv6_sockglue.c:492 [inline]
ipv6_setsockopt+0x3758/0x3910 net/ipv6/ipv6_sockglue.c:1019
udpv6_setsockopt+0x85/0x90 net/ipv6/udp.c:1649
sock_common_setsockopt+0x5d/0x70 net/core/sock.c:3489
__sys_setsockopt+0x209/0x2a0 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff8881386f7aa8 of 8 bytes by task 26911 on cpu 1:
inet6_recvmsg+0x7a/0x210 net/ipv6/af_inet6.c:659
____sys_recvmsg+0x16c/0x320
___sys_recvmsg net/socket.c:2674 [inline]
do_recvmmsg+0x3f5/0xae0 net/socket.c:2768
__sys_recvmmsg net/socket.c:2847 [inline]
__do_sys_recvmmsg net/socket.c:2870 [inline]
__se_sys_recvmmsg net/socket.c:2863 [inline]
__x64_sys_recvmmsg+0xde/0x160 net/socket.c:2863
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0xffffffff85e0e980 -> 0xffffffff85e01580
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 26911 Comm: syz-executor.3 Not tainted 5.17.0-rc2-syzkaller-00316-g0457e5153e0e-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DSA support for the phylink mac_select_pcs() method so DSA drivers
can return provide phylink with the appropriate PCS for the PHY
interface mode.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP sendmsg() can be lockless, this is causing all kinds
of data races.
This patch converts sk->sk_tskey to remove one of these races.
BUG: KCSAN: data-race in __ip_append_data / __ip_append_data
read to 0xffff8881035d4b6c of 4 bytes by task 8877 on cpu 1:
__ip_append_data+0x1c1/0x1de0 net/ipv4/ip_output.c:994
ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
write to 0xffff8881035d4b6c of 4 bytes by task 8880 on cpu 0:
__ip_append_data+0x1d8/0x1de0 net/ipv4/ip_output.c:994
ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000054d -> 0x0000054e
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 8880 Comm: syz-executor.5 Not tainted 5.17.0-rc2-syzkaller-00167-gdcb85f85fa6f-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 09c2d251b7 ("net-timestamp: add key to disambiguate concurrent datagrams")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow table lookup is skipped if packet either went through ct clear
action (which set the IP_CT_UNTRACKED flag on the packet), or while
switching zones and there is already a connection associated with
the packet. This will result in no SW offload of the connection,
and the and connection not being removed from flow table with
TCP teardown (fin/rst packet).
To fix the above, remove these unneccary checks in flow
table lookup.
Fixes: 46475bb20f ("net/sched: act_ct: Software offload of established flows")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bringing down the netdevice or system shutdown, a panic can be
triggered while accessing the sysfs path because the device is already
removed.
[ 755.549084] mlx5_core 0000:12:00.1: Shutdown was called
[ 756.404455] mlx5_core 0000:12:00.0: Shutdown was called
...
[ 757.937260] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 758.031397] IP: [<ffffffff8ee11acb>] dma_pool_alloc+0x1ab/0x280
crash> bt
...
PID: 12649 TASK: ffff8924108f2100 CPU: 1 COMMAND: "amsd"
...
#9 [ffff89240e1a38b0] page_fault at ffffffff8f38c778
[exception RIP: dma_pool_alloc+0x1ab]
RIP: ffffffff8ee11acb RSP: ffff89240e1a3968 RFLAGS: 00010046
RAX: 0000000000000246 RBX: ffff89243d874100 RCX: 0000000000001000
RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff89243d874090
RBP: ffff89240e1a39c0 R8: 000000000001f080 R9: ffff8905ffc03c00
R10: ffffffffc04680d4 R11: ffffffff8edde9fd R12: 00000000000080d0
R13: ffff89243d874090 R14: ffff89243d874080 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#10 [ffff89240e1a39c8] mlx5_alloc_cmd_msg at ffffffffc04680f3 [mlx5_core]
#11 [ffff89240e1a3a18] cmd_exec at ffffffffc046ad62 [mlx5_core]
#12 [ffff89240e1a3ab8] mlx5_cmd_exec at ffffffffc046b4fb [mlx5_core]
#13 [ffff89240e1a3ae8] mlx5_core_access_reg at ffffffffc0475434 [mlx5_core]
#14 [ffff89240e1a3b40] mlx5e_get_fec_caps at ffffffffc04a7348 [mlx5_core]
#15 [ffff89240e1a3bb0] get_fec_supported_advertised at ffffffffc04992bf [mlx5_core]
#16 [ffff89240e1a3c08] mlx5e_get_link_ksettings at ffffffffc049ab36 [mlx5_core]
#17 [ffff89240e1a3ce8] __ethtool_get_link_ksettings at ffffffff8f25db46
#18 [ffff89240e1a3d48] speed_show at ffffffff8f277208
#19 [ffff89240e1a3dd8] dev_attr_show at ffffffff8f0b70e3
#20 [ffff89240e1a3df8] sysfs_kf_seq_show at ffffffff8eedbedf
#21 [ffff89240e1a3e18] kernfs_seq_show at ffffffff8eeda596
#22 [ffff89240e1a3e28] seq_read at ffffffff8ee76d10
#23 [ffff89240e1a3e98] kernfs_fop_read at ffffffff8eedaef5
#24 [ffff89240e1a3ed8] vfs_read at ffffffff8ee4e3ff
#25 [ffff89240e1a3f08] sys_read at ffffffff8ee4f27f
#26 [ffff89240e1a3f50] system_call_fastpath at ffffffff8f395f92
crash> net_device.state ffff89443b0c0000
state = 0x5 (__LINK_STATE_START| __LINK_STATE_NOCARRIER)
To prevent this scenario, we also make sure that the netdevice is present.
Signed-off-by: suresh kumar <suresh2514@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced in commit cf96357303 ("net: dsa: Allow providing PHY
statistics from CPU port"), it appears these were never used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220216193726.2926320-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
prot->memory_allocated should only be set if prot->sysctl_mem
is also set.
This is a followup of commit 2520611151 ("crypto: af_alg - get
rid of alg_memory_allocated").
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220216171801.3604366-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf 2022-02-17
We've added 8 non-merge commits during the last 7 day(s) which contain
a total of 8 files changed, 119 insertions(+), 15 deletions(-).
The main changes are:
1) Add schedule points in map batch ops, from Eric.
2) Fix bpf_msg_push_data with len 0, from Felix.
3) Fix crash due to incorrect copy_map_value, from Kumar.
4) Fix crash due to out of bounds access into reg2btf_ids, from Kumar.
5) Fix a bpf_timer initialization issue with clang, from Yonghong.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add schedule points in batch ops
bpf: Fix crash due to out of bounds access into reg2btf_ids.
selftests: bpf: Check bpf_msg_push_data return value
bpf: Fix a bpf_timer initialization issue
bpf: Emit bpf_timer in vmlinux BTF
selftests/bpf: Add test for bpf_timer overwriting crash
bpf: Fix crash due to incorrect copy_map_value
bpf: Do not try bpf_msg_push_data with len 0
====================
Link: https://lore.kernel.org/r/20220217190000.37925-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fib_alias_hw_flags_set() can be used by concurrent threads,
and is only RCU protected.
We need to annotate accesses to following fields of struct fib_alias:
offload, trap, offload_failed
Because of READ_ONCE()WRITE_ONCE() limitations, make these
field u8.
BUG: KCSAN: data-race in fib_alias_hw_flags_set / fib_alias_hw_flags_set
read to 0xffff888134224a6a of 1 bytes by task 2013 on cpu 1:
fib_alias_hw_flags_set+0x28a/0x470 net/ipv4/fib_trie.c:1050
nsim_fib4_rt_hw_flags_set drivers/net/netdevsim/fib.c:350 [inline]
nsim_fib4_rt_add drivers/net/netdevsim/fib.c:367 [inline]
nsim_fib4_rt_insert drivers/net/netdevsim/fib.c:429 [inline]
nsim_fib4_event drivers/net/netdevsim/fib.c:461 [inline]
nsim_fib_event drivers/net/netdevsim/fib.c:881 [inline]
nsim_fib_event_work+0x1852/0x2cf0 drivers/net/netdevsim/fib.c:1477
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
process_scheduled_works kernel/workqueue.c:2370 [inline]
worker_thread+0x7df/0xa70 kernel/workqueue.c:2456
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
write to 0xffff888134224a6a of 1 bytes by task 4872 on cpu 0:
fib_alias_hw_flags_set+0x2d5/0x470 net/ipv4/fib_trie.c:1054
nsim_fib4_rt_hw_flags_set drivers/net/netdevsim/fib.c:350 [inline]
nsim_fib4_rt_add drivers/net/netdevsim/fib.c:367 [inline]
nsim_fib4_rt_insert drivers/net/netdevsim/fib.c:429 [inline]
nsim_fib4_event drivers/net/netdevsim/fib.c:461 [inline]
nsim_fib_event drivers/net/netdevsim/fib.c:881 [inline]
nsim_fib_event_work+0x1852/0x2cf0 drivers/net/netdevsim/fib.c:1477
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
process_scheduled_works kernel/workqueue.c:2370 [inline]
worker_thread+0x7df/0xa70 kernel/workqueue.c:2456
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
value changed: 0x00 -> 0x02
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 4872 Comm: kworker/0:0 Not tainted 5.17.0-rc3-syzkaller-00188-g1d41d2e82623-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events nsim_fib_event_work
Fixes: 90b93f1b31 ("ipv4: Add "offload" and "trap" indications to routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220216173217.3792411-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Check for a hwaccel VLAN tag on rx and use it if present. Otherwise,
use __skb_vlan_pop() like the other tag parsers do. This fixes the case
where the VLAN tag has already been consumed by the master.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220216124634.23123-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
vsock_connect() expects that the socket could already be in the
TCP_ESTABLISHED state when the connecting task wakes up with a signal
pending. If this happens the socket will be in the connected table, and
it is not removed when the socket state is reset. In this situation it's
common for the process to retry connect(), and if the connection is
successful the socket will be added to the connected table a second
time, corrupting the list.
Prevent this by calling vsock_remove_connected() if a signal is received
while waiting for a connection. This is harmless if the socket is not in
the connected table, and if it is in the table then removing it will
prevent list corruption from a double add.
Note for backporting: this patch requires d5afa82c97 ("vsock: correct
removal of socket from the list"), which is in all current stable trees
except 4.9.y.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Seth Forshee <sforshee@digitalocean.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20220217141312.2297547-1-sforshee@digitalocean.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before freeing the hash table in addrconf_exit_net(),
we need to make sure the work queue has completed,
or risk NULL dereference or UAF.
Thus, use cancel_delayed_work_sync() to enforce this.
We do not hold RTNL in addrconf_exit_net(), making this safe.
Fixes: 8805d13ff1 ("ipv6/addrconf: use one delayed work per netns")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220216182037.3742-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sprinkle for each loops to allow netdevices to be unregistered
out of order, as their refs are released.
This prevents problems caused by dependencies between netdevs
which want to release references in their ->priv_destructor.
See commit d6ff94afd9 ("vlan: move dev_put into vlan_dev_uninit")
for example.
Eric has removed the only known ordering requirement in
commit c002496bab ("Merge branch 'ipv6-loopback'")
so let's try this and see if anything explodes...
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/20220215225310.3679266-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In prep for unregistering netdevs out of order move the netdev
state validation and change outside of the loop.
While at it modernize this code and use WARN() instead of
pr_err() + dump_stack().
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/20220215225310.3679266-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When 'ping' changes to use PING socket instead of RAW socket by:
# sysctl -w net.ipv4.ping_group_range="0 100"
There is another regression caused when matching sk_bound_dev_if
and dif, RAW socket is using inet_iif() while PING socket lookup
is using skb->dev->ifindex, the cmd below fails due to this:
# ip link add dummy0 type dummy
# ip link set dummy0 up
# ip addr add 192.168.111.1/24 dev dummy0
# ping -I dummy0 192.168.111.1 -c1
The issue was also reported on:
https://github.com/iputils/iputils/issues/104
But fixed in iputils in a wrong way by not binding to device when
destination IP is on device, and it will cause some of kselftests
to fail, as Jianlin noticed.
This patch is to use inet(6)_iif and inet(6)_sdif to get dif and
sdif for PING socket, and keep consistent with RAW socket.
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support setting IPV6_HOPLIMIT, IPV6_TCLASS, IPV6_DONTFRAG
during sendmsg via SOL_IPV6 cmsgs.
tclass and dontfrag are init'ed from struct ipv6_pinfo in
ipcm6_init_sk(), while hlimit is inited to -1, so we need
to handle it being populated via cmsg explicitly.
Leave extension headers and flowlabel unimplemented.
Those are slightly more laborious to test and users
seem to primarily care about IPV6_TCLASS.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA inherits NETIF_F_CSUM_MASK from master->vlan_features, and the
expectation is that TX checksumming is offloaded and not done in
software.
Normally the DSA master takes care of this, but packets handled by
ocelot_defer_xmit() are a very special exception, because they are
actually injected into the switch through register-based MMIO. So the
DSA master is not involved at all for these packets => no one calculates
the checksum.
This allows PTP over UDP to work using the ocelot-8021q tagging
protocol.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both get and dump handlers for RTM_GETSTATS require that a filter_mask, a
mask of which attributes should be emitted in the netlink response, is
unset. rtnl_stats_dump() does include an extack in the bounce,
rtnl_stats_get() however does not. Fix the omission.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/01feb1f4bbd22a19f6629503c4f366aed6424567.1645020876.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Assign the helpers directly rather than save/restore in the context
structure.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These structures are initialised from the init hooks, so we can't make
them 'const'. But no writes occur afterwards, so we can use ro_after_init.
Also, remove bogus EXPORT_SYMBOL, the only access comes from ip
stack, not from kernel modules.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A few pm-related helpers don't touch arguments which lacking
the const modifier, let's constify them.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop the port parameter of mptcp_pm_add_addr_signal() and reflect it to
avoid passing too many parameters.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop the unneeded type casts to 'unsigned long long' for printing out the
hmac values in add_addr_hmac_valid() and subflow_thmac_valid().
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The parameter 'sk' became useless since the code using it was dropped
from mptcp_get_options() in the commit 8d548ea1dd ("mptcp: do not set
unconditionally csum_reqd on incoming opt"). Let's drop it.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add setsockopt support for SO_SNDTIMEO_OLD and SO_SNDTIMEO_NEW to fix this
error reported by the mptcp bpf selftest:
(network_helpers.c:64: errno: Operation not supported) Failed to set SO_SNDTIMEO
test_mptcp:FAIL:115
All error logs:
(network_helpers.c:64: errno: Operation not supported) Failed to set SO_SNDTIMEO
test_mptcp:FAIL:115
Summary: 0/0 PASSED, 0 SKIPPED, 1 FAILED
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous bug fix had an unfortunate side effect that broke
distribution of binding table entries between nodes. The updated
tipc_sock_addr struct is also used further down in the same
function, and there the old value is still the correct one.
Fixes: 032062f363 ("tipc: fix wrong publisher node address in link publications")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/20220216020009.3404578-1-jmaloy@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ipv6 flowlabels historically require a reservation before use.
Optionally in exclusive mode (e.g., user-private).
Commit 59c820b231 ("ipv6: elide flowlabel check if no exclusive
leases exist") introduced a fastpath that avoids this check when no
exclusive leases exist in the system, and thus any flowlabel use
will be granted.
That allows skipping the control operation to reserve a flowlabel
entirely. Though with a warning if the fast path fails:
This is an optimization. Robust applications still have to revert to
requesting leases if the fast path fails due to an exclusive lease.
Still, this is subtle. Better isolate network namespaces from each
other. Flowlabels are per-netns. Also record per-netns whether
exclusive leases are in use. Then behavior does not change based on
activity in other netns.
Changes
v2
- wrap in IS_ENABLED(CONFIG_IPV6) to avoid breakage if disabled
Fixes: 59c820b231 ("ipv6: elide flowlabel check if no exclusive leases exist")
Link: https://lore.kernel.org/netdev/MWHPR2201MB1072BCCCFCE779E4094837ACD0329@MWHPR2201MB1072.namprd22.prod.outlook.com/
Reported-by: Congyu Liu <liu3101@purdue.edu>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Tested-by: Congyu Liu <liu3101@purdue.edu>
Link: https://lore.kernel.org/r/20220215160037.1976072-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__skb_vlan_pop() needs skb->data to point at the mac_header, while
skb_vlan_tag_present() and skb_vlan_tag_get() don't, because they don't
look at skb->data at all.
So we can avoid uselessly moving around skb->data for the case where the
VLAN tag was offloaded by the DSA master.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220215204722.2134816-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever bridge driver hits the max capacity of MDBs, it disables
the MC processing (by setting corresponding bridge option), but never
notifies switchdev about such change (the notifiers are called only upon
explicit setting of this option, through the registered netlink interface).
This could lead to situation when Software MDB processing gets disabled,
but this event never gets offloaded to the underlying Hardware.
Fix this by adding a notify message in such case.
Fixes: 147c1e9b90 ("switchdev: bridge: Offload multicast disabled")
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20220215165303.31908-1-oleksandr.mazur@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When smc_connect_clc() times out, it will return -EAGAIN(tcp_recvmsg
retuns -EAGAIN while timeout), then this value will passed to the
application, which is quite confusing to the applications, makes
inconsistency with TCP.
From the manual of connect, ETIMEDOUT is more suitable, and this patch
try convert EAGAIN to ETIMEDOUT in that case.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/1644913490-21594-1-git-send-email-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refer to housekeeping APIs using single feature types instead of flags.
This prevents from passing multiple isolation features at once to
housekeeping interfaces, which soon won't be possible anymore as each
isolation features will have their own cpumask.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juri Lelli <juri.lelli@redhat.com>
Reviewed-by: Phil Auld <pauld@redhat.com>
Link: https://lore.kernel.org/r/20220207155910.527133-5-frederic@kernel.org
To prepare for supporting each feature of the housekeeping cpumask
toward cpuset, prepare each of the HK_FLAG_* entries to move to their
own cpumask with enforcing to fetch them individually. The new
constraint is that multiple HK_FLAG_* entries can't be mixed together
anymore in a single call to housekeeping cpumask().
This will later allow, for example, to runtime modify the cpulist passed
through "isolcpus=", "nohz_full=" and "rcu_nocbs=" kernel boot
parameters.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juri Lelli <juri.lelli@redhat.com>
Reviewed-by: Phil Auld <pauld@redhat.com>
Link: https://lore.kernel.org/r/20220207155910.527133-4-frederic@kernel.org
In EHT requesting aggregation with 1K needs the use of extended
the AddBA element for the buffer size, so add the logic to parse
it and make sure it's in limits of the EHT aggregation size.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Link: https://lore.kernel.org/r/20220214173004.8209cae9d9e4.I434f5588602f83b4e658c660120040913b3a2e3d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We add the fields for parsing extended ADDBA request/respond,
and new max 1K aggregation for limit ADDBA request/respond.
Adjust drivers to use the proper macro, IEEE80211_MAX_AMPDU_BUF ->
IEEE80211_MAX_AMPDU_BUF_HE.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Link: https://lore.kernel.org/r/20220214173004.b8b447ce95b7.I0ee2554c94e89abc7a752b0f7cc7fd79c273efea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are two problems with the current code that have been highlighted
with the AQL feature that is now enbaled by default.
First problem is in ieee80211_rx_h_mesh_fwding(),
ieee80211_select_queue_80211() is used on received packets to choose
the sending AC queue of the forwarding packet although this function
should only be called on TX packet (it uses ieee80211_tx_info).
This ends with forwarded mesh packets been sent on unrelated random AC
queue. To fix that, AC queue can directly be infered from skb->priority
which has been extracted from QOS info (see ieee80211_parse_qos()).
Second problem is the value of queue_mapping set on forwarded mesh
frames via skb_set_queue_mapping() is not the AC of the packet but a
hardware queue index. This may or may not work depending on AC to HW
queue mapping which is driver specific.
Both of these issues lead to improper AC selection while forwarding
mesh packets but more importantly due to improper airtime accounting
(which is done on a per STA, per AC basis) caused traffic stall with
the introduction of AQL.
Fixes: cf44012810 ("mac80211: fix unnecessary frame drops in mesh fwding")
Fixes: d3c1597b8d ("mac80211: fix forwarded mesh frame queue mapping")
Co-developed-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://lore.kernel.org/r/20220214173214.368862-1-nico.escande@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an MFP station isn't authorized, the receiver will (or
at least should) drop the action frame since it's a robust
management frame, but if we're not authorized we haven't
installed keys yet. Refuse attempts to start a session as
they'd just time out.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20220203201528.ff4d5679dce9.I34bb1f2bc341e161af2d6faf74f91b332ba11285@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 set capability NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211
to upper layer by default. That means we should pass EAPoL packets through
nl80211 path only, and should not send the EAPoL skb to netdevice diretly.
At the meanwhile, wpa_supplicant would not register sock to listen EAPoL
skb on the netdevice.
However, there is no control_port_protocol handler in mac80211 for 802.3 RX
packets, mac80211 driver would pass up the EAPoL rekey frame to netdevice
and wpa_supplicant would be never interactive with this kind of packets,
if SUPPORTS_RX_DECAP_OFFLOAD is enabled. This causes STA always rekey fail
if EAPoL frame go through 802.3 path.
To avoid this problem, align the same process as 802.11 type to handle
this frame before put it into network stack.
This also addresses a potential security issue in 802.3 RX mode that was
previously fixed in commit a8c4d76a8d ("mac80211: do not accept/forward
invalid EAPOL frames").
Cc: stable@vger.kernel.org # 5.12+
Fixes: 80a915ec44 ("mac80211: add rx decapsulation offload support")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Link: https://lore.kernel.org/r/6889c9fced5859ebb088564035f84fd0fa792a49.1644680751.git.deren.wu@mediatek.com
[fix typos, update comment and add note about security issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
DSA now explicitly handles VLANs installed with the 'self' flag on the
bridge as host VLANs, instead of just replicating every bridge port VLAN
also on the CPU port and never deleting it, which is what it did before.
However, this leaves a corner case uncovered, as explained by
Tobias Waldekranz:
https://patchwork.kernel.org/project/netdevbpf/patch/20220209213044.2353153-6-vladimir.oltean@nxp.com/#24735260
Forwarding towards a bridge port VLAN installed on a bridge port foreign
to DSA (separate NIC, Wi-Fi AP) used to work by virtue of the fact that
DSA itself needed to have at least one port in that VLAN (therefore, it
also had the CPU port in said VLAN). However, now that the CPU port may
not be member of all VLANs that user ports are members of, we need to
ensure this isn't the case if software forwarding to a foreign interface
is required.
The solution is to treat bridge port VLANs on standalone interfaces in
the exact same way as host VLANs. From DSA's perspective, there is no
difference between local termination and software forwarding; packets in
that VLAN must reach the CPU in both cases.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, DSA programs VLANs on shared (DSA and CPU) ports each time it
does so on user ports. This is good for basic functionality but has
several limitations:
- the VLAN group which must reach the CPU may be radically different
from the VLAN group that must be autonomously forwarded by the switch.
In other words, the admin may want to isolate noisy stations and avoid
traffic from them going to the control processor of the switch, where
it would just waste useless cycles. The bridge already supports
independent control of VLAN groups on bridge ports and on the bridge
itself, and when VLAN-aware, it will drop packets in software anyway
if their VID isn't added as a 'self' entry towards the bridge device.
- Replaying host FDB entries may depend, for some drivers like mv88e6xxx,
on replaying the host VLANs as well. The 2 VLAN groups are
approximately the same in most regular cases, but there are corner
cases when timing matters, and DSA's approximation of replicating
VLANs on shared ports simply does not work.
- If a user makes the bridge (implicitly the CPU port) join a VLAN by
accident, there is no way for the CPU port to isolate itself from that
noisy VLAN except by rebooting the system. This is because for each
VLAN added on a user port, DSA will add it on shared ports too, but
for each VLAN deletion on a user port, it will remain installed on
shared ports, since DSA has no good indication of whether the VLAN is
still in use or not.
Now that the bridge driver emits well-balanced SWITCHDEV_OBJ_ID_PORT_VLAN
addition and removal events, DSA has a simple and straightforward task
of separating the bridge port VLANs (these have an orig_dev which is a
DSA slave interface, or a LAG interface) from the host VLANs (these have
an orig_dev which is a bridge interface), and to keep a simple reference
count of each VID on each shared port.
Forwarding VLANs must be installed on the bridge ports and on all DSA
ports interconnecting them. We don't have a good view of the exact
topology, so we simply install forwarding VLANs on all DSA ports, which
is what has been done until now.
Host VLANs must be installed primarily on the dedicated CPU port of each
bridge port. More subtly, they must also be installed on upstream-facing
and downstream-facing DSA ports that are connecting the bridge ports and
the CPU. This ensures that the mv88e6xxx's problem (VID of host FDB
entry may be absent from VTU) is still addressed even if that switch is
in a cross-chip setup, and it has no local CPU port.
Therefore:
- user ports contain only bridge port (forwarding) VLANs, and no
refcounting is necessary
- DSA ports contain both forwarding and host VLANs. Refcounting is
necessary among these 2 types.
- CPU ports contain only host VLANs. Refcounting is also necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev_handle_port_obj_add() helper is good for replicating a
port object on the lower interfaces of @dev, if that object was emitted
on a bridge, or on a bridge port that is a LAG.
However, drivers that use this helper limit themselves to a box from
which they can no longer intercept port objects notified on neighbor
ports ("foreign interfaces").
One such driver is DSA, where software bridging with foreign interfaces
such as standalone NICs or Wi-Fi APs is an important use case. There, a
VLAN installed on a neighbor bridge port roughly corresponds to a
forwarding VLAN installed on the DSA switch's CPU port.
To support this use case while also making use of the benefits of the
switchdev_handle_* replication helper for port objects, introduce a new
variant of these functions that crawls through the neighbor ports of
@dev, in search of potentially compatible switchdev ports that are
interested in the event.
The strategy is identical to switchdev_handle_fdb_event_to_device():
if @dev wasn't a switchdev interface, then go one step upper, and
recursively call this function on the bridge that this port belongs to.
At the next recursion step, __switchdev_handle_port_obj_add() will
iterate through the bridge's lower interfaces. Among those, some will be
switchdev interfaces, and one will be the original @dev that we came
from. To prevent infinite recursion, we must suppress reentry into the
original @dev, and just call the @add_cb for the switchdev_interfaces.
It looks like this:
br0
/ | \
/ | \
/ | \
swp0 swp1 eth0
1. __switchdev_handle_port_obj_add(eth0)
-> check_cb(eth0) returns false
-> eth0 has no lower interfaces
-> eth0's bridge is br0
-> switchdev_lower_dev_find(br0, check_cb, foreign_dev_check_cb))
finds br0
2. __switchdev_handle_port_obj_add(br0)
-> check_cb(br0) returns false
-> netdev_for_each_lower_dev
-> check_cb(swp0) returns true, so we don't skip this interface
3. __switchdev_handle_port_obj_add(swp0)
-> check_cb(swp0) returns true, so we call add_cb(swp0)
(back to netdev_for_each_lower_dev from 2)
-> check_cb(swp1) returns true, so we don't skip this interface
4. __switchdev_handle_port_obj_add(swp1)
-> check_cb(swp1) returns true, so we call add_cb(swp1)
(back to netdev_for_each_lower_dev from 2)
-> check_cb(eth0) returns false, so we skip this interface to
avoid infinite recursion
Note: eth0 could have been a LAG, and we don't want to suppress the
recursion through its lowers if those exist, so when check_cb() returns
false, we still call switchdev_lower_dev_find() to estimate whether
there's anything worth a recursion beneath that LAG. Using check_cb()
and foreign_dev_check_cb(), switchdev_lower_dev_find() not only figures
out whether the lowers of the LAG are switchdev, but also whether they
actively offload the LAG or not (whether the LAG is "foreign" to the
switchdev interface or not).
The port_obj_info->orig_dev is preserved across recursive calls, so
switchdev drivers still know on which device was this notification
originally emitted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev_lower_dev_find() assumes RCU read-side critical section
calling context, since it uses netdev_walk_all_lower_dev_rcu().
Rename it appropriately, in preparation of adding a similar iterator
that assumes writer-side rtnl_mutex protection.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The major user of replayed switchdev objects is DSA, and so far it
hasn't needed information about anything other than bridge port VLANs,
so this is all that br_switchdev_vlan_replay() knows to handle.
DSA has managed to get by through replicating every VLAN addition on a
user port such that the same VLAN is also added on all DSA and CPU
ports, but there is a corner case where this does not work.
The mv88e6xxx DSA driver currently prints this error message as soon as
the first port of a switch joins a bridge:
mv88e6085 0x0000000008b96000:00: port 0 failed to add a6:ef:77:c8:5f:3d vid 1 to fdb: -95
where a6:ef:77:c8:5f:3d vid 1 is a local FDB entry corresponding to the
bridge MAC address in the default_pvid.
The -EOPNOTSUPP is returned by mv88e6xxx_port_db_load_purge() because it
tries to map VID 1 to a FID (the ATU is indexed by FID not VID), but
fails to do so. This is because ->port_fdb_add() is called before
->port_vlan_add() for VID 1.
The abridged timeline of the calls is:
br_add_if
-> netdev_master_upper_dev_link
-> dsa_port_bridge_join
-> switchdev_bridge_port_offload
-> br_switchdev_vlan_replay (*)
-> br_switchdev_fdb_replay
-> mv88e6xxx_port_fdb_add
-> nbp_vlan_init
-> nbp_vlan_add
-> mv88e6xxx_port_vlan_add
and the issue is that at the time of (*), the bridge port isn't in VID 1
(nbp_vlan_init hasn't been called), therefore br_switchdev_vlan_replay()
won't have anything to replay, therefore VID 1 won't be in the VTU by
the time mv88e6xxx_port_fdb_add() is called.
This happens only when the first port of a switch joins. For further
ports, the initial mv88e6xxx_port_vlan_add() is sufficient for VID 1 to
be loaded in the VTU (which is switch-wide, not per port).
The problem is somewhat unique to mv88e6xxx by chance, because most
other drivers offload an FDB entry by VID, so FDBs and VLANs can be
added asynchronously with respect to each other, but addressing the
issue at the bridge layer makes sense, since what mv88e6xxx requires
isn't absurd.
To fix this problem, we need to recognize that it isn't the VLAN group
of the port that we're interested in, but the VLAN group of the bridge
itself (so it isn't a timing issue, but rather insufficient information
being passed from switchdev to drivers).
As mentioned, currently nbp_switchdev_sync_objs() only calls
br_switchdev_vlan_replay() for VLANs corresponding to the port, but the
VLANs corresponding to the bridge itself, for local termination, also
need to be replayed. In this case, VID 1 is not (yet) present in the
port's VLAN group but is present in the bridge's VLAN group.
So to fix this bug, DSA is now obligated to explicitly handle VLANs
pointing towards the bridge in order to "close this race" (which isn't
really a race). As Tobias Waldekranz notices, this also implies that it
must explicitly handle port VLANs on foreign interfaces, something that
worked implicitly before:
https://patchwork.kernel.org/project/netdevbpf/patch/20220209213044.2353153-6-vladimir.oltean@nxp.com/#24735260
So in the end, br_switchdev_vlan_replay() must replay all VLANs from all
VLAN groups: all the ports, and the bridge itself.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be switchdev drivers that can add/remove a FDB or MDB entry
only as long as the VLAN it's in has been notified and offloaded first.
The nbp_switchdev_sync_objs() method satisfies this requirement on
addition, but nbp_switchdev_unsync_objs() first deletes VLANs, then
deletes MDBs and FDBs. Reverse the order of the function calls to cater
to this requirement.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_switchdev_port_vlan_add() currently emits a SWITCHDEV_PORT_OBJ_ADD
event with a SWITCHDEV_OBJ_ID_PORT_VLAN for 2 distinct cases:
- a struct net_bridge_vlan got created
- an existing struct net_bridge_vlan was modified
This makes it impossible for switchdev drivers to properly balance
PORT_OBJ_ADD with PORT_OBJ_DEL events, so if we want to allow that to
happen, we must provide a way for drivers to distinguish between a
VLAN with changed flags and a new one.
Annotate struct switchdev_obj_port_vlan with a "bool changed" that
distinguishes the 2 cases above.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when a VLAN entry is added multiple times in a row to a
bridge port, nbp_vlan_add() calls br_switchdev_port_vlan_add() each
time, even if the VLAN already exists and nothing about it has changed:
bridge vlan add dev lan12 vid 100 master static
Similarly, when a VLAN is added multiple times in a row to a bridge,
br_vlan_add_existing() doesn't filter at all the calls to
br_switchdev_port_vlan_add():
bridge vlan add dev br0 vid 100 self
This behavior makes driver-level accounting of VLANs impossible, since
it is enough for a single deletion event to remove a VLAN, but the
addition event can be emitted an unlimited number of times.
The cause for this can be identified as follows: we rely on
__vlan_add_flags() to retroactively tell us whether it has changed
anything about the VLAN flags or VLAN group pvid. So we'd first have to
call __vlan_add_flags() before calling br_switchdev_port_vlan_add(), in
order to have access to the "bool *changed" information. But we don't
want to change the event ordering, because we'd have to revert the
struct net_bridge_vlan changes we've made if switchdev returns an error.
So to solve this, we need another function that tells us whether any
change is going to occur in the VLAN or VLAN group, _prior_ to calling
__vlan_add_flags().
Split __vlan_add_flags() into a precommit and a commit stage, and rename
it to __vlan_flags_update(). The precommit stage,
__vlan_flags_would_change(), will determine whether there is any reason
to notify switchdev due to a change of flags (note: the BRENTRY flag
transition from false to true is treated separately: as a new switchdev
entry, because we skipped notifying the master VLAN when it wasn't a
brentry yet, and therefore not as a change of flags).
With this lookahead/precommit function in place, we can avoid notifying
switchdev if nothing changed for the VLAN and VLAN group.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is a very subtle aspect to the behavior of
__vlan_add_flags(): it changes the struct net_bridge_vlan flags and
pvid, yet it returns true ("changed") even if none of those changed,
just a transition of br_vlan_is_brentry(v) took place from false to
true.
This can be seen in br_vlan_add_existing(), however we do not actually
rely on this subtle behavior, since the "if" condition that checks that
the vlan wasn't a brentry before had a useless (until now) assignment:
*changed = true;
Make things more obvious by actually making __vlan_add_flags() do what's
written on the box, and be more specific about what is actually written
on the box. This is needed because further transformations will be done
to __vlan_add_flags().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added to a bridge port and it doesn't exist on the bridge
device yet, it gets created for the multicast context, but it is
'hidden', since it doesn't have the BRENTRY flag yet:
ip link add br0 type bridge && ip link set swp0 master br0
bridge vlan add dev swp0 vid 100 # the master VLAN 100 gets created
bridge vlan add dev br0 vid 100 self # that VLAN becomes brentry just now
All switchdev drivers ignore switchdev notifiers for VLAN entries which
have the BRENTRY unset, and for good reason: these are merely private
data structures used by the bridge driver. So we might just as well not
notify those at all.
Cleanup in the switchdev drivers that check for the BRENTRY flag is now
possible, and will be handled separately, since those checks just became
dead code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added to a bridge port, a master VLAN gets created on the
bridge for context, but it doesn't have the BRENTRY flag.
Then, when the same VLAN is added to the bridge itself, that enters
through the br_vlan_add_existing() code path and gains the BRENTRY flag,
thus it becomes "existing".
It seems natural to check for this condition early, because the current
code flow is to notify switchdev of the addition of a VLAN that isn't a
brentry, just to delete it immediately afterwards.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
security_sctp_assoc_established() is added to replace
security_inet_conn_established() called in
sctp_sf_do_5_1E_ca(), so that asoc can be accessed in security
subsystem and save the peer secid to asoc->peer_secid.
Fixes: 72e89f5008 ("security: Add support for SCTP security hooks")
Reported-by: Prashanth Prahlad <pprahlad@redhat.com>
Based-on-patch-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Tested-by: Richard Haines <richard_c_haines@btinternet.com>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Clang static analysis reports this problem
route.c:425:4: warning: Use of memory after it is freed
trace_mctp_key_acquire(key);
^~~~~~~~~~~~~~~~~~~~~~~~~~~
When mctp_key_add() fails, key is freed but then is later
used in trace_mctp_key_acquire(). Add an else statement
to use the key only when mctp_key_add() is successful.
Fixes: 4f9e1ba6de ("mctp: Add tracepoints for tag/key handling")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the following call path returns an error from switchdev:
nbp_vlan_flush
-> __vlan_del
-> __vlan_vid_del
-> br_switchdev_port_vlan_del
-> __vlan_group_free
-> WARN_ON(!list_empty(&vg->vlan_list));
then the deletion of the net_bridge_vlan is silently halted, which will
trigger the WARN_ON from __vlan_group_free().
The WARN_ON is rather unhelpful, because nothing about the source of the
error is printed. Add a print to catch errors from __vlan_del.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple containers are running in the environment and multiple
macvlan network port are configured in each container, a lot of martian
source prints will appear after martian_log is enabled. they are almost
the same, and printed by net_warn_ratelimited. Each arp message will
trigger this print on each network port.
Such as:
IPv4: martian source 173.254.95.16 from 173.254.100.109,
on dev eth0
ll header: 00000000: ff ff ff ff ff ff 40 00 ad fe 64 6d
08 06 ......@...dm..
IPv4: martian source 173.254.95.16 from 173.254.100.109,
on dev eth1
ll header: 00000000: ff ff ff ff ff ff 40 00 ad fe 64 6d
08 06 ......@...dm..
There is no description of this kind of source in the RFC1812.
Signed-off-by: Zhang Yunkai <zhang.yunkai@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link comes up we add its presence to the name table to make it
possible for users to subscribe for link up/down events. However, after
a previous call signature change the binding is wrongly published with
the peer node as publishing node, instead of the own node as it should
be. This has the effect that the command 'tipc name table show' will
list the link binding (service type 2) with node scope and a peer node
as originator, something that obviously is impossible.
We correct this bug here.
Fixes: 50a3499ab8 ("tipc: simplify signature of tipc_namtbl_publish()")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/20220214013852.2803940-1-jmaloy@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever rt6_uncached_list_flush_dev() swaps rt->rt6_idev
to the blackhole device, parts of IPv6 stack might still need
to increment one SNMP counter.
Root cause, patch from Ido, changelog from Eric :)
This bug suggests that we need to audit rt->rt6_idev usages
and make sure they are properly using RCU protection.
Fixes: e5f80fcf86 ("ipv6: give an IPv6 dev to blackhole_netdev")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes return value documentation of kernel_getsockname()
and kernel_getpeername() functions.
The previous documentation wrongly specified that the return
value is 0 in case of success, however sock->ops->getname returns
the length of the address in bytes in case of success.
Signed-off-by: Alex Maydanik <alexander.maydanik@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling interrupts and in the RPS case locking input_pkt_queue is
split into local_irq_disable() and optional spin_lock().
This breaks on PREEMPT_RT because the spinlock_t typed lock can not be
acquired with disabled interrupts.
The sections in which the lock is acquired is usually short in a sense that it
is not causing long und unbounded latiencies. One exception is the
skb_flow_limit() invocation which may invoke a BPF program (and may
require sleeping locks).
By moving local_irq_disable() + spin_lock() into rps_lock(), we can keep
interrupts disabled on !PREEMPT_RT and enabled on PREEMPT_RT kernels.
Without RPS on a PREEMPT_RT kernel, the needed synchronisation happens
as part of local_bh_disable() on the local CPU.
____napi_schedule() is only invoked if sd is from the local CPU. Replace
it with __napi_schedule_irqoff() which already disables interrupts on
PREEMPT_RT as needed. Move this call to rps_ipi_queued() and rename the
function to napi_schedule_rps as suggested by Jakub.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave suggested a while ago (eleven years by now) "Let's make netif_rx()
work in all contexts and get rid of netif_rx_ni()". Eric agreed and
pointed out that modern devices should use netif_receive_skb() to avoid
the overhead.
In the meantime someone added another variant, netif_rx_any_context(),
which behaves as suggested.
netif_rx() must be invoked with disabled bottom halves to ensure that
pending softirqs, which were raised within the function, are handled.
netif_rx_ni() can be invoked only from process context (bottom halves
must be enabled) because the function handles pending softirqs without
checking if bottom halves were disabled or not.
netif_rx_any_context() invokes on the former functions by checking
in_interrupts().
netif_rx() could be taught to handle both cases (disabled and enabled
bottom halves) by simply disabling bottom halves while invoking
netif_rx_internal(). The local_bh_enable() invocation will then invoke
pending softirqs only if the BH-disable counter drops to zero.
Eric is concerned about the overhead of BH-disable+enable especially in
regard to the loopback driver. As critical as this driver is, it will
receive a shortcut to avoid the additional overhead which is not needed.
Add a local_bh_disable() section in netif_rx() to ensure softirqs are
handled if needed.
Provide __netif_rx() which does not disable BH and has a lockdep assert
to ensure that interrupts are disabled. Use this shortcut in the
loopback driver and in drivers/net/*.c.
Make netif_rx_ni() and netif_rx_any_context() invoke netif_rx() so they
can be removed once they are no more users left.
Link: https://lkml.kernel.org/r/20100415.020246.218622820.davem@davemloft.net
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The preempt_disable() () section was introduced in commit
cece1945bf ("net: disable preemption before call smp_processor_id()")
and adds it in case this function is invoked from preemtible context and
because get_cpu() later on as been added.
The get_cpu() usage was added in commit
b0e28f1eff ("net: netif_rx() must disable preemption")
because ip_dev_loopback_xmit() invoked netif_rx() with enabled preemption
causing a warning in smp_processor_id(). The function netif_rx() should
only be invoked from an interrupt context which implies disabled
preemption. The commit
e30b38c298 ("ip: Fix ip_dev_loopback_xmit()")
was addressing this and replaced netif_rx() with in netif_rx_ni() in
ip_dev_loopback_xmit().
Based on the discussion on the list, the former patch (b0e28f1eff)
should not have been applied only the latter (e30b38c298).
Remove get_cpu() and preempt_disable() since the function is supposed to
be invoked from context with stable per-CPU pointers. Bottom halves have
to be disabled at this point because the function may raise softirqs
which need to be processed.
Link: https://lkml.kernel.org/r/20100415.013347.98375530.davem@davemloft.net
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx is special among DSA drivers in that it requires the VTU to
contain the VID of the FDB entry it modifies in
mv88e6xxx_port_db_load_purge(), otherwise it will return -EOPNOTSUPP.
Sometimes due to races this is not always satisfied even if external
code does everything right (first deletes the FDB entries, then the
VLAN), because DSA commits to hardware FDB entries asynchronously since
commit c9eb3e0f87 ("net: dsa: Add support for learning FDB through
notification").
Therefore, the mv88e6xxx driver must close this race condition by
itself, by asking DSA to flush the switchdev workqueue of any FDB
deletions in progress, prior to exiting a VLAN.
Fixes: c9eb3e0f87 ("net: dsa: Add support for learning FDB through notification")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reasons to __udp6_lib_rcv for skb drops. The only twist is that the
NO_SOCKET takes precedence over the CSUM or other counters for that
path (motivation behind this patch - csum counter was misleading).
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch introduces a lock-free version of smc_tx_work() to
solve unnecessary lock contention, which is expected to be held lock.
So this adds comment to remind people to keep an eye out for locks.
Suggested-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generate RTM_NEWROUTE netlink notification when the route preference
changes on an existing kernel generated default route in response to
RA messages. Currently netlink notifications are generated only when
this route is added or deleted but not when the route preference
changes, which can cause userspace routing application state to go
out of sync with kernel.
Signed-off-by: Kalash Nainwal <kalash@arista.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
in current Linux, MTU policing does not take into account that packets at
the TC ingress have the L2 header pulled. Thus, the same TC police action
(with the same value of tcfp_mtu) behaves differently for ingress/egress.
In addition, the full GSO size is compared to tcfp_mtu: as a consequence,
the policer drops GSO packets even when individual segments have the L2 +
L3 + L4 + payload length below the configured valued of tcfp_mtu.
Improve the accuracy of MTU policing as follows:
- account for mac_len for non-GSO packets at TC ingress.
- compare MTU threshold with the segmented size for GSO packets.
Also, add a kselftest that verifies the correct behavior.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_defrag_ipv6_disable() requires CONFIG_IP6_NF_IPTABLES.
Fixes: 75063c9294 ("netfilter: xt_socket: fix a typo in socket_mt_destroy()")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Eric Dumazet<edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
msg_data_sz return a 32bit value, but size is 16bit. This may lead to a
bit overflow.
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for v5.18, with both wireless and stack patches.
rtw89 now has AP mode support and wcn36xx has survey support. But
otherwise pretty normal.
Major changes:
ath11k
* add LDPC FEC type in 802.11 radiotap header
* enable RX PPDU stats in monitor co-exist mode
wcn36xx
* implement survey reporting
brcmfmac
* add CYW43570 PCIE device
rtw88
* rtw8821c: enable RFE 6 devices
rtw89
* AP mode support
mt76
* mt7916 support
* background radar detection support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmIGLrkRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZsgWAf/aQb18PB2Wh+tH4qxkNW6jK3zfYSRDbDQ
QvrHcnN4BINorTLcGDvWqw3VANiETCW6mVBG8BWo1NyAlvkNziKaAFI3xVhuOE38
6d+wRVElG9JHeb6OwWCX2vWJmqWVxmEIAkTQrqT9VSSUjGDpS1mc3dAssABeEZhn
yzSKJomSRaRv/aC2f/4eYPAyeMUIZbN3VWFOvElGPls0mdrSBmt9OhAKkf3A3E0M
PuJzhnHgoKhpZ/Gmn+IrDZGC/RkUOfT2zZ5gUK0GVvpTFg2/80ilC7RJk2iF5Ibs
xGuRN9WSo9xWILF3SyRgrrx3ocZG0H2dvkJj4ZQbR485U8iXa+HC1g==
=AUlw
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-02-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
wireless-next patches for v5.18
First set of patches for v5.18, with both wireless and stack patches.
rtw89 now has AP mode support and wcn36xx has survey support. But
otherwise pretty normal.
Major changes:
ath11k
* add LDPC FEC type in 802.11 radiotap header
* enable RX PPDU stats in monitor co-exist mode
wcn36xx
* implement survey reporting
brcmfmac
* add CYW43570 PCIE device
rtw88
* rtw8821c: enable RFE 6 devices
rtw89
* AP mode support
mt76
* mt7916 support
* background radar detection support
Second set of fixes for v5.17. This is the first pull request with
both driver and stack patches.
Most important here are a regression fix for brcmfmac USB devices and
an iwlwifi fix for use after free when the firmware was missing. We
have new maintainers for ath9k and wcn36xx as well as ath6kl is now
orphaned. Also smaller fixes to iwlwifi and stack.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmIGLQoRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZvMSwf/QSGm9vlSC1rfiG/+cy65pg1bY4m7DM1g
fiZJP3X690jBzi45B6ld3sI47DdycJH5jhyj7A9DIp2sPNGuULaGNjUrV2eQpjjk
BU2tBOBLy/P9aoyMuRTeF4H2QXMgRXGTVhVF4oydmzOigKyJx1GxOt4tfkqPATYb
3SEKp2wbwUjGA0K4xCD0LFnJHFcp3XSHFRNLN6QpZz/Ku+BcLq+cUWfHUKqDZFl4
rNa4BH5xyydFNNURM6K20iKacq/8s5JOxdGAS+OmBGXKyZT/kbxvZDNz3rUsXuhd
C7MYkQPGeXayfTrJbHwV2CBpaN+hy3KkU0ecOG6FACu9H4hfoJfynA==
=ioe+
-----END PGP SIGNATURE-----
Merge tag 'wireless-2022-02-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
wireless fixes for v5.17
Second set of fixes for v5.17. This is the first pull request with
both driver and stack patches.
Most important here are a regression fix for brcmfmac USB devices and
an iwlwifi fix for use after free when the firmware was missing. We
have new maintainers for ath9k and wcn36xx as well as ath6kl is now
orphaned. Also smaller fixes to iwlwifi and stack.
If bpf_msg_push_data() is called with len 0 (as it happens during
selftests/bpf/test_sockmap), we do not need to do anything and can
return early.
Calling bpf_msg_push_data() with len 0 previously lead to a wrong ENOMEM
error: we later called get_order(copy + len); if len was 0, copy + len
was also often 0 and get_order() returned some undefined value (at the
moment 52). alloc_pages() caught that and failed, but then bpf_msg_push_data()
returned ENOMEM. This was wrong because we are most probably not out of
memory and actually do not need any additional memory.
Fixes: 6fff607e2f ("bpf: sk_msg program helper bpf_msg_push_data")
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/df69012695c7094ccb1943ca02b4920db3537466.1644421921.git.fmaurer@redhat.com
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Add selftest for nft_synproxy, from Florian Westphal.
2) xt_socket destroy path incorrectly disables IPv4 defrag for
IPv6 traffic (typo), from Eric Dumazet.
3) Fix exit value selftest nft_concat_range.sh, from Hangbin Liu.
4) nft_synproxy disables the IPv4 hooks if the IPv6 hooks fail
to be registered.
5) disable rp_filter on router in selftest nft_fib.sh, also
from Hangbin Liu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an optimization to keep the per-cpu lists as short as possible:
Whenever rt_flush_dev() changes one rtable dst.dev
matching the disappearing device, it can can transfer the object
to a quarantine list, waiting for a final rt_del_uncached_list().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an optimization to keep the per-cpu lists as short as possible:
Whenever rt6_uncached_list_flush_dev() changes one rt6_info
matching the disappearing device, it can can transfer the object
to a quarantine list, waiting for a final rt6_uncached_list_del().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 addrconf notifiers wants the loopback device to
be the last device being dismantled at netns deletion.
This caused many limitations and work arounds.
Back in linux-5.3, Mahesh added a per host blackhole_netdev
that can be used whenever we need to make sure objects no longer
refer to a disappearing device.
If we attach to blackhole_netdev an ip6_ptr (allocate an idev),
then we can use this special device (which is never freed)
in place of the loopback_dev (which can be freed).
This will permit improvements in netdev_run_todo() and other parts
of the stack where had steps to make sure loopback_dev was
the last device to disappear.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This counter has never been visible, there is little point
trying to maintain it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trace_napi_poll_hit() is reading stat->dev while another thread can write
on it from dropmon_net_event()
Use READ_ONCE()/WRITE_ONCE() here, RCU rules are properly enforced already,
we only have to take care of load/store tearing.
BUG: KCSAN: data-race in dropmon_net_event / trace_napi_poll_hit
write to 0xffff88816f3ab9c0 of 8 bytes by task 20260 on cpu 1:
dropmon_net_event+0xb8/0x2b0 net/core/drop_monitor.c:1579
notifier_call_chain kernel/notifier.c:84 [inline]
raw_notifier_call_chain+0x53/0xb0 kernel/notifier.c:392
call_netdevice_notifiers_info net/core/dev.c:1919 [inline]
call_netdevice_notifiers_extack net/core/dev.c:1931 [inline]
call_netdevice_notifiers net/core/dev.c:1945 [inline]
unregister_netdevice_many+0x867/0xfb0 net/core/dev.c:10415
ip_tunnel_delete_nets+0x24a/0x280 net/ipv4/ip_tunnel.c:1123
vti_exit_batch_net+0x2a/0x30 net/ipv4/ip_vti.c:515
ops_exit_list net/core/net_namespace.c:173 [inline]
cleanup_net+0x4dc/0x8d0 net/core/net_namespace.c:597
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
read to 0xffff88816f3ab9c0 of 8 bytes by interrupt on cpu 0:
trace_napi_poll_hit+0x89/0x1c0 net/core/drop_monitor.c:292
trace_napi_poll include/trace/events/napi.h:14 [inline]
__napi_poll+0x36b/0x3f0 net/core/dev.c:6366
napi_poll net/core/dev.c:6432 [inline]
net_rx_action+0x29e/0x650 net/core/dev.c:6519
__do_softirq+0x158/0x2de kernel/softirq.c:558
do_softirq+0xb1/0xf0 kernel/softirq.c:459
__local_bh_enable_ip+0x68/0x70 kernel/softirq.c:383
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
_raw_spin_unlock_bh+0x33/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:394 [inline]
ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
wg_packet_decrypt_worker+0x73c/0x780 drivers/net/wireguard/receive.c:506
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
value changed: 0xffff88815883e000 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 26435 Comm: kworker/0:1 Not tainted 5.17.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: wg-crypt-wg2 wg_packet_decrypt_worker
Fixes: 4ea7e38696 ("dropmon: add ability to detect when hardware dropsrxpackets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->rtm_tos option is normally used to route packets based on both
the destination address and the DS field. However it's ignored for
IPv6 routes. Setting ->rtm_tos for IPv6 is thus invalid as the route
is going to work only on the destination address anyway, so it won't
behave as specified.
Suggested-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), suggested by Cong Wang, the
DSA interfaces and their master have different dev->nested_level, which
makes netif_addr_lock() stop complaining about potentially recursive
locking on the same lock class.
So we no longer need DSA slave interfaces to have their own lockdep
class.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), suggested by Cong Wang, the
DSA interfaces and their master have different dev->nested_level, which
makes netif_addr_lock() stop complaining about potentially recursive
locking on the same lock class.
So we no longer need DSA masters to have their own lockdep class.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no legacy ports, DSA registers a devlink instance with ports
unconditionally for all switch drivers. Therefore, delete the old-style
ndo operations used for determining bridge forwarding domains.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we can control SMC handshake limitation through socket options,
which means that applications who need it must modify their code. It's
quite troublesome for many existing applications. This patch modifies
the global default value of SMC handshake limitation through netlink,
providing a way to put constraint on handshake without modifies any code
for applications.
Suggested-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to add dynamic control for SMC handshake limitation for
every smc sockets, in production environment, it is possible for the
same applications to handle different service types, and may have
different opinion on SMC handshake limitation.
This patch try socket options to complete it, since we don't have socket
option level for SMC yet, which requires us to implement it at the same
time.
This patch does the following:
- add new socket option level: SOL_SMC.
- add new SMC socket option: SMC_LIMIT_HS.
- provide getter/setter for SMC socket options.
Link: https://lore.kernel.org/all/20f504f961e1a803f85d64229ad84260434203bd.1644323503.git.alibuda@linux.alibaba.com/
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch intends to provide a mechanism to put constraint on SMC
connections visit according to the pressure of SMC handshake process.
At present, frequent visits will cause the incoming connections to be
backlogged in SMC handshake queue, raise the connections established
time. Which is quite unacceptable for those applications who base on
short lived connections.
There are two ways to implement this mechanism:
1. Put limitation after TCP established.
2. Put limitation before TCP established.
In the first way, we need to wait and receive CLC messages that the
client will potentially send, and then actively reply with a decline
message, in a sense, which is also a sort of SMC handshake, affect the
connections established time on its way.
In the second way, the only problem is that we need to inject SMC logic
into TCP when it is about to reply the incoming SYN, since we already do
that, it's seems not a problem anymore. And advantage is obvious, few
additional processes are required to complete the constraint.
This patch use the second way. After this patch, connections who beyond
constraint will not informed any SMC indication, and SMC will not be
involved in any of its subsequent processes.
Link: https://lore.kernel.org/all/1641301961-59331-1-git-send-email-alibuda@linux.alibaba.com/
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation does not handling backlog semantics, one
potential risk is that server will be flooded by infinite amount
connections, even if client was SMC-incapable.
This patch works to put a limit on backlog connections, referring to the
TCP implementation, we divides SMC connections into two categories:
1. Half SMC connection, which includes all TCP established while SMC not
connections.
2. Full SMC connection, which includes all SMC established connections.
For half SMC connection, since all half SMC connections starts with TCP
established, we can achieve our goal by put a limit before TCP
established. Refer to the implementation of TCP, this limits will based
on not only the half SMC connections but also the full connections,
which is also a constraint on full SMC connections.
For full SMC connections, although we know exactly where it starts, it's
quite hard to put a limit before it. The easiest way is to block wait
before receive SMC confirm CLC message, while it's under protection by
smc_server_lgr_pending, a global lock, which leads this limit to the
entire host instead of a single listen socket. Another way is to drop
the full connections, but considering the cast of SMC connections, we
prefer to keep full SMC connections.
Even so, the limits of full SMC connections still exists, see commits
about half SMC connection below.
After this patch, the limits of backend connection shows like:
For SMC:
1. Client with SMC-capability can makes 2 * backlog full SMC connections
or 1 * backlog half SMC connections and 1 * backlog full SMC
connections at most.
2. Client without SMC-capability can only makes 1 * backlog half TCP
connections and 1 * backlog full TCP connections.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multithread and 10K connections benchmark, the backend TCP connection
established very slowly, and lots of TCP connections stay in SYN_SENT
state.
Client: smc_run wrk -c 10000 -t 4 http://server
the netstate of server host shows like:
145042 times the listen queue of a socket overflowed
145042 SYNs to LISTEN sockets dropped
One reason of this issue is that, since the smc_tcp_listen_work() shared
the same workqueue (smc_hs_wq) with smc_listen_work(), while the
smc_listen_work() do blocking wait for smc connection established. Once
the workqueue became congested, it's will block the accept() from TCP
listen.
This patch creates a independent workqueue(smc_tcp_ls_wq) for
smc_tcp_listen_work(), separate it from smc_listen_work(), which is
quite acceptable considering that smc_tcp_listen_work() runs very fast.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback functions of clcsock will be saved and replaced during
the fallback. But if the fallback happens more than once, then the
copies of these callback functions will be overwritten incorrectly,
resulting in a loop call issue:
clcsk->sk_error_report
|- smc_fback_error_report() <------------------------------|
|- smc_fback_forward_wakeup() | (loop)
|- clcsock_callback() (incorrectly overwritten) |
|- smc->clcsk_error_report() ------------------|
So this patch fixes the issue by saving these function pointers only
once in the fallback and avoiding overwriting.
Reported-by: syzbot+4de3c0e8a263e1e499bc@syzkaller.appspotmail.com
Fixes: 341adeec9a ("net/smc: Forward wakeup to smc socket waitqueue after fallback")
Link: https://lore.kernel.org/r/0000000000006d045e05d78776f6@google.com
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - new code bugs:
- sparx5: fix get_stat64 out-of-bound access and crash
- smc: fix netdev ref tracker misuse
Previous releases - regressions:
- eth: ixgbevf: require large buffers for build_skb on 82599VF,
avoid overflows
- eth: ocelot: fix all IP traffic getting trapped to CPU with PTP
over IP
- bonding: fix rare link activation misses in 802.3ad mode
Previous releases - always broken:
- tcp: fix tcp sock mem accounting in zero-copy corner cases
- remove the cached dst when uncloning an skb dst and its metadata,
since we only have one ref it'd lead to an UaF
- netfilter:
- conntrack: don't refresh sctp entries in closed state
- conntrack: re-init state for retransmitted syn-ack, avoid
connection establishment getting stuck with strange stacks
- ctnetlink: disable helper autoassign, avoid it getting lost
- nft_payload: don't allow transport header access for fragments
- dsa: fix use of devres for mdio throughout drivers
- eth: amd-xgbe: disable interrupts during pci removal
- eth: dpaa2-eth: unregister netdev before disconnecting the PHY
- eth: ice: fix IPIP and SIT TSO offload
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=jlhJ
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter and can.
Current release - new code bugs:
- sparx5: fix get_stat64 out-of-bound access and crash
- smc: fix netdev ref tracker misuse
Previous releases - regressions:
- eth: ixgbevf: require large buffers for build_skb on 82599VF, avoid
overflows
- eth: ocelot: fix all IP traffic getting trapped to CPU with PTP
over IP
- bonding: fix rare link activation misses in 802.3ad mode
Previous releases - always broken:
- tcp: fix tcp sock mem accounting in zero-copy corner cases
- remove the cached dst when uncloning an skb dst and its metadata,
since we only have one ref it'd lead to an UaF
- netfilter:
- conntrack: don't refresh sctp entries in closed state
- conntrack: re-init state for retransmitted syn-ack, avoid
connection establishment getting stuck with strange stacks
- ctnetlink: disable helper autoassign, avoid it getting lost
- nft_payload: don't allow transport header access for fragments
- dsa: fix use of devres for mdio throughout drivers
- eth: amd-xgbe: disable interrupts during pci removal
- eth: dpaa2-eth: unregister netdev before disconnecting the PHY
- eth: ice: fix IPIP and SIT TSO offload"
* tag 'net-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (53 commits)
net: dsa: mv88e6xxx: fix use-after-free in mv88e6xxx_mdios_unregister
net: mscc: ocelot: fix mutex lock error during ethtool stats read
ice: Avoid RTNL lock when re-creating auxiliary device
ice: Fix KASAN error in LAG NETDEV_UNREGISTER handler
ice: fix IPIP and SIT TSO offload
ice: fix an error code in ice_cfg_phy_fec()
net: mpls: Fix GCC 12 warning
dpaa2-eth: unregister the netdev before disconnecting from the PHY
skbuff: cleanup double word in comment
net: macb: Align the dma and coherent dma masks
mptcp: netlink: process IPv6 addrs in creating listening sockets
selftests: mptcp: add missing join check
net: usb: qmi_wwan: Add support for Dell DW5829e
vlan: move dev_put into vlan_dev_uninit
vlan: introduce vlan_dev_free_egress_priority
ax25: fix UAF bugs of net_device caused by rebinding operation
net: dsa: fix panic when DSA master device unbinds on shutdown
net: amd-xgbe: disable interrupts during pci removal
tipc: rate limit warning for received illegal binding update
net: mdio: aspeed: Add missing MODULE_DEVICE_TABLE
...
Replace zero-length array with flexible-array member and make use
of the struct_size() helper in kmalloc(). For example:
struct switchdev_deferred_item {
...
unsigned long data[];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable the IPv4 hooks if the IPv6 hooks fail to be registered.
Fixes: ad49d86e07 ("netfilter: nf_tables: Add synproxy support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit 563f8e97e0 ("ipv4: Stop taking ECN bits into account in
fib4-rules") replaced the validation test on frh->tos. While the new
test is stricter for ECN bits, it doesn't detect the use of high order
DSCP bits. This would be fine if IPv4 could properly handle them. But
currently, most IPv4 lookups are done with the three high DSCP bits
masked. Therefore, using these bits doesn't lead to the expected
result.
Let's reject such configurations again, so that nobody starts to
use and make any assumption about how the stack handles the three high
order DSCP bits in fib4 rules.
Fixes: 563f8e97e0 ("ipv4: Stop taking ECN bits into account in fib4-rules")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having to acquire rtnl from netdev_run_todo() for every dismantled
device is not desirable when/if rtnl is under stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with automatic stack variable initialization, GCC 12
complains about variables defined outside of switch case statements.
Move the variable outside the switch, which silences the warning:
./net/mpls/af_mpls.c:1624:21: error: statement will never be executed [-Werror=switch-unreachable]
1624 | int err;
| ^~~
Signed-off-by: Victor Erminpour <victor.erminpour@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor reordering of the code and a call to sock_cmsg_send()
gives us support for setting the common socket options via
cmsg (the usual ones - SO_MARK, SO_TIMESTAMPING_OLD, SCM_TXTIME).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing prevents the user from requesting timestamping
on ping6 sockets, yet timestamps are not going to be reported.
Plumb the flags through.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have ftrace and BPF today, there's no need for printing arguments
at the start of a function.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2022-02-10
An update from ieee802154 for your *net-next* tree.
There is more ongoing in ieee802154 than usual. This will be the first pull
request for this cycle, but I expect one more. Depending on review and rework
times.
Pavel Skripkin ported the atusb driver over to the new USB api to avoid unint
problems as well as making use of the modern api without kmalloc() needs in he
driver.
Miquel Raynal landed some changes to ensure proper frame checksum checking with
hwsim, documenting our use of wake and stop_queue and eliding a magic value by
using the proper define.
David Girault documented the address struct used in ieee802154.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_mon_rcv() allows a node to receive and process
domain_record structs from peer nodes to track their views of the
network topology.
This patch verifies that the number of members in a received domain
record does not exceed the limit defined by MAX_MON_DOMAIN, something
that may otherwise lead to a stack overflow.
tipc_mon_rcv() is called from the function tipc_link_proto_rcv(), where
we are reading a 32 bit message data length field into a uint16. To
avert any risk of bit overflow, we add an extra sanity check for this in
that function. We cannot see that happen with the current code, but
future designers being unaware of this risk, may introduce it by
allowing delivery of very large (> 64k) sk buffers from the bearer
layer. This potential problem was identified by Eric Dumazet.
This fixes CVE-2022-0435
Reported-by: Samuel Page <samuel.page@appgate.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 35c55c9877 ("tipc: add neighbor monitoring framework")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Samuel Page <samuel.page@appgate.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change updates mptcp_pm_nl_create_listen_socket() to create
listening sockets bound to IPv6 addresses (where IPv6 is supported).
Fixes: 1729cf186d ("mptcp: create the listening socket for new port")
Acked-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Kishen Maloor <kishen.maloor@intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Conntrack sets on CHECKSUM_UNNECESSARY for UDP packet with no checksum,
from Kevin Mitchell.
2) skb->priority support for nfqueue, from Nicolas Dichtel.
3) Remove conntrack extension register API, from Florian Westphal.
4) Move nat destroy hook to nf_nat_hook instead, to remove
nf_ct_ext_destroy(), also from Florian.
5) Wrap pptp conntrack NAT hooks into single structure, from Florian Westphal.
6) Support for tcp option set to noop for nf_tables, also from Florian.
7) Do not run x_tables comment match from packet path in nf_tables,
from Florian Westphal.
8) Replace spinlock by cmpxchg() loop to update missed ct event,
from Florian Westphal.
9) Wrap cttimeout hooks into single structure, from Florian.
10) Add fast nft_cmp expression for up to 16-bytes.
11) Use cb->ctx to store context in ctnetlink dump, instead of using
cb->args[], from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: ctnetlink: use dump structure instead of raw args
nfqueue: enable to set skb->priority
netfilter: nft_cmp: optimize comparison for 16-bytes
netfilter: cttimeout: use option structure
netfilter: ecache: don't use nf_conn spinlock
netfilter: nft_compat: suppress comment match
netfilter: exthdr: add support for tcp option removal
netfilter: conntrack: pptp: use single option structure
netfilter: conntrack: remove extension register api
netfilter: conntrack: handle ->destroy hook via nat_ops instead
netfilter: conntrack: move extension sizes into core
netfilter: conntrack: make all extensions 8-byte alignned
netfilter: nfqueue: enable to get skb->priority
netfilter: conntrack: mark UDP zero checksum as CHECKSUM_UNNECESSARY
====================
Link: https://lore.kernel.org/r/20220209133616.165104-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit
9652dc2eb9 ("tcp: relax listening_hash operations")
removed the need to disable bottom half while acquiring
listening_hash.lock. There are still two callers left which disable
bottom half before the lock is acquired.
On PREEMPT_RT the softirqs are preemptible and local_bh_disable() acts
as a lock to ensure that resources, that are protected by disabling
bottom halves, remain protected.
This leads to a circular locking dependency if the lock acquired with
disabled bottom halves is also acquired with enabled bottom halves
followed by disabling bottom halves. This is the reverse locking order.
It has been observed with inet_listen_hashbucket:🔒
local_bh_disable() + spin_lock(&ilb->lock):
inet_listen()
inet_csk_listen_start()
sk->sk_prot->hash() := inet_hash()
local_bh_disable()
__inet_hash()
spin_lock(&ilb->lock);
acquire(&ilb->lock);
Reverse order: spin_lock(&ilb2->lock) + local_bh_disable():
tcp_seq_next()
listening_get_next()
spin_lock(&ilb2->lock);
acquire(&ilb2->lock);
tcp4_seq_show()
get_tcp4_sock()
sock_i_ino()
read_lock_bh(&sk->sk_callback_lock);
acquire(softirq_ctrl) // <---- whoops
acquire(&sk->sk_callback_lock)
Drop local_bh_disable() around __inet_hash() which acquires
listening_hash->lock. Split inet_unhash() and acquire the
listen_hashbucket lock without disabling bottom halves; the inet_ehash
lock with disabled bottom halves.
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lkml.kernel.org/r/12d6f9879a97cd56c09fb53dee343cbb14f7f1f7.camel@gmx.de
Link: https://lkml.kernel.org/r/X9CheYjuXWc75Spa@hirez.programming.kicks-ass.net
Link: https://lore.kernel.org/r/YgQOebeZ10eNx1W6@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-02-09
We've added 126 non-merge commits during the last 16 day(s) which contain
a total of 201 files changed, 4049 insertions(+), 2215 deletions(-).
The main changes are:
1) Add custom BPF allocator for JITs that pack multiple programs into a huge
page to reduce iTLB pressure, from Song Liu.
2) Add __user tagging support in vmlinux BTF and utilize it from BPF
verifier when generating loads, from Yonghong Song.
3) Add per-socket fast path check guarding from cgroup/BPF overhead when
used by only some sockets, from Pavel Begunkov.
4) Continued libbpf deprecation work of APIs/features and removal of their
usage from samples, selftests, libbpf & bpftool, from Andrii Nakryiko
and various others.
5) Improve BPF instruction set documentation by adding byte swap
instructions and cleaning up load/store section, from Christoph Hellwig.
6) Switch BPF preload infra to light skeleton and remove libbpf dependency
from it, from Alexei Starovoitov.
7) Fix architecture-agnostic macros in libbpf for accessing syscall
arguments from BPF progs for non-x86 architectures,
from Ilya Leoshkevich.
8) Rework port members in struct bpf_sk_lookup and struct bpf_sock to be
of 16-bit field with anonymous zero padding, from Jakub Sitnicki.
9) Add new bpf_copy_from_user_task() helper to read memory from a different
task than current. Add ability to create sleepable BPF iterator progs,
from Kenny Yu.
10) Implement XSK batching for ice's zero-copy driver used by AF_XDP and
utilize TX batching API from XSK buffer pool, from Maciej Fijalkowski.
11) Generate temporary netns names for BPF selftests to avoid naming
collisions, from Hangbin Liu.
12) Implement bpf_core_types_are_compat() with limited recursion for
in-kernel usage, from Matteo Croce.
13) Simplify pahole version detection and finally enable CONFIG_DEBUG_INFO_DWARF5
to be selected with CONFIG_DEBUG_INFO_BTF, from Nathan Chancellor.
14) Misc minor fixes to libbpf and selftests from various folks.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (126 commits)
selftests/bpf: Cover 4-byte load from remote_port in bpf_sk_lookup
bpf: Make remote_port field in struct bpf_sk_lookup 16-bit wide
libbpf: Fix compilation warning due to mismatched printf format
selftests/bpf: Test BPF_KPROBE_SYSCALL macro
libbpf: Add BPF_KPROBE_SYSCALL macro
libbpf: Fix accessing the first syscall argument on s390
libbpf: Fix accessing the first syscall argument on arm64
libbpf: Allow overriding PT_REGS_PARM1{_CORE}_SYSCALL
selftests/bpf: Skip test_bpf_syscall_macro's syscall_arg1 on arm64 and s390
libbpf: Fix accessing syscall arguments on riscv
libbpf: Fix riscv register names
libbpf: Fix accessing syscall arguments on powerpc
selftests/bpf: Use PT_REGS_SYSCALL_REGS in bpf_syscall_macro
libbpf: Add PT_REGS_SYSCALL_REGS macro
selftests/bpf: Fix an endianness issue in bpf_syscall_macro test
bpf: Fix bpf_prog_pack build HPAGE_PMD_SIZE
bpf: Fix leftover header->pages in sparc and powerpc code.
libbpf: Fix signedness bug in btf_dump_array_data()
selftests/bpf: Do not export subtest as standalone test
bpf, x86_64: Fail gracefully on bpf_jit_binary_pack_finalize failures
...
====================
Link: https://lore.kernel.org/r/20220209210050.8425-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the commit c504e5c2f9 ("net: skb: introduce kfree_skb_reason()")
drop reason is introduced to the tracepoint of kfree_skb. Therefore,
drop_monitor is able to report the drop reason to users by netlink.
The drop reasons are reported as string to users, which is exactly
the same as what we do when reporting it to ftrace.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220209060838.55513-1-imagedong@tencent.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
remote_port is another case of a BPF context field documented as a 32-bit
value in network byte order for which the BPF context access converter
generates a load of a zero-padded 16-bit integer in network byte order.
First such case was dst_port in bpf_sock which got addressed in commit
4421a58271 ("bpf: Make dst_port field in struct bpf_sock 16-bit wide").
Loading 4-bytes from the remote_port offset and converting the value with
bpf_ntohl() leads to surprising results, as the expected value is shifted
by 16 bits.
Reduce the confusion by splitting the field in two - a 16-bit field holding
a big-endian integer, and a 16-bit zero-padding anonymous field that
follows it.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20220209184333.654927-2-jakub@cloudflare.com
Shuang Li reported an QinQ issue by simply doing:
# ip link add dummy0 type dummy
# ip link add link dummy0 name dummy0.1 type vlan id 1
# ip link add link dummy0.1 name dummy0.1.2 type vlan id 2
# rmmod 8021q
unregister_netdevice: waiting for dummy0.1 to become free. Usage count = 1
When rmmods 8021q, all vlan devs are deleted from their real_dev's vlan grp
and added into list_kill by unregister_vlan_dev(). dummy0.1 is unregistered
before dummy0.1.2, as it's using for_each_netdev() in __rtnl_kill_links().
When unregisters dummy0.1, dummy0.1.2 is not unregistered in the event of
NETDEV_UNREGISTER, as it's been deleted from dummy0.1's vlan grp. However,
due to dummy0.1.2 still holding dummy0.1, dummy0.1 will keep waiting in
netdev_wait_allrefs(), while dummy0.1.2 will never get unregistered and
release dummy0.1, as it delays dev_put until calling dev->priv_destructor,
vlan_dev_free().
This issue was introduced by Commit 563bcbae3b ("net: vlan: fix a UAF in
vlan_dev_real_dev()"), and this patch is to fix it by moving dev_put() into
vlan_dev_uninit(), which is called after NETDEV_UNREGISTER event but before
netdev_wait_allrefs().
Fixes: 563bcbae3b ("net: vlan: fix a UAF in vlan_dev_real_dev()")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to introduce vlan_dev_free_egress_priority() to
free egress priority for vlan dev, and keep vlan_dev_uninit()
static as .ndo_uninit. It makes the code more clear and safer
when adding new code in vlan_dev_uninit() in the future.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ax25_kill_by_device() will set s->ax25_dev = NULL and
call ax25_disconnect() to change states of ax25_cb and
sock, if we call ax25_bind() before ax25_kill_by_device().
However, if we call ax25_bind() again between the window of
ax25_kill_by_device() and ax25_dev_device_down(), the values
and states changed by ax25_kill_by_device() will be reassigned.
Finally, ax25_dev_device_down() will deallocate net_device.
If we dereference net_device in syscall functions such as
ax25_release(), ax25_sendmsg(), ax25_getsockopt(), ax25_getname()
and ax25_info_show(), a UAF bug will occur.
One of the possible race conditions is shown below:
(USE) | (FREE)
ax25_bind() |
| ax25_kill_by_device()
ax25_bind() |
ax25_connect() | ...
| ax25_dev_device_down()
| ...
| dev_put_track(dev, ...) //FREE
ax25_release() | ...
ax25_send_control() |
alloc_skb() //USE |
the corresponding fail log is shown below:
===============================================================
BUG: KASAN: use-after-free in ax25_send_control+0x43/0x210
...
Call Trace:
...
ax25_send_control+0x43/0x210
ax25_release+0x2db/0x3b0
__sock_release+0x6d/0x120
sock_close+0xf/0x20
__fput+0x11f/0x420
...
Allocated by task 1283:
...
__kasan_kmalloc+0x81/0xa0
alloc_netdev_mqs+0x5a/0x680
mkiss_open+0x6c/0x380
tty_ldisc_open+0x55/0x90
...
Freed by task 1969:
...
kfree+0xa3/0x2c0
device_release+0x54/0xe0
kobject_put+0xa5/0x120
tty_ldisc_kill+0x3e/0x80
...
In order to fix these UAF bugs caused by rebinding operation,
this patch adds dev_hold_track() into ax25_bind() and
corresponding dev_put_track() into ax25_kill_by_device().
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafael reports that on a system with LX2160A and Marvell DSA switches,
if a reboot occurs while the DSA master (dpaa2-eth) is up, the following
panic can be seen:
systemd-shutdown[1]: Rebooting.
Unable to handle kernel paging request at virtual address 00a0000800000041
[00a0000800000041] address between user and kernel address ranges
Internal error: Oops: 96000004 [#1] PREEMPT SMP
CPU: 6 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00042-g8f5585009b24 #32
pc : dsa_slave_netdevice_event+0x130/0x3e4
lr : raw_notifier_call_chain+0x50/0x6c
Call trace:
dsa_slave_netdevice_event+0x130/0x3e4
raw_notifier_call_chain+0x50/0x6c
call_netdevice_notifiers_info+0x54/0xa0
__dev_close_many+0x50/0x130
dev_close_many+0x84/0x120
unregister_netdevice_many+0x130/0x710
unregister_netdevice_queue+0x8c/0xd0
unregister_netdev+0x20/0x30
dpaa2_eth_remove+0x68/0x190
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
__do_sys_reboot+0x1cc/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
It can be seen from the stack trace that the problem is that the
deregistration of the master causes a dev_close(), which gets notified
as NETDEV_GOING_DOWN to dsa_slave_netdevice_event().
But dsa_switch_shutdown() has already run, and this has unregistered the
DSA slave interfaces, and yet, the NETDEV_GOING_DOWN handler attempts to
call dev_close_many() on those slave interfaces, leading to the problem.
The previous attempt to avoid the NETDEV_GOING_DOWN on the master after
dsa_switch_shutdown() was called seems improper. Unregistering the slave
interfaces is unnecessary and unhelpful. Instead, after the slaves have
stopped being uppers of the DSA master, we can now reset to NULL the
master->dsa_ptr pointer, which will make DSA start ignoring all future
notifier events on the master.
Fixes: 0650bf52b3 ("net: dsa: be compatible with masters which unregister on shutdown")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It would be easy to craft a message containing an illegal binding table
update operation. This is handled correctly by the code, but the
corresponding warning printout is not rate limited as is should be.
We fix this now.
Fixes: b97bf3fd8f ("[TIPC] Initial merge")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmIDdE4THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXdbzB/9aYlSVCqS1tKOS57MmXBam1OrD5M6Y
R0PuMISj8zUvwKp/nLfTGG6MyPtlxLh5qK5Wu9Eq38jfKlHh64XhFbmZmVwc34ji
JzZO6znObncaWsDAUSIdv6uDB7OIuGQ94xgUXBvTkXhXnBn9P8kEWPKV6F1jSzGS
fpE3WVlRLq5DT322B51O/QXn4ET9bNacEIX9Y+teU8YkTqRowokkCwTgGt7PHo7M
M2f4ojHGUaABzkpyhK7eUOmGcmZYdQF84MrQhkQ+CF1NRzBnulH6NIJr5/PRCmy0
PWVDfnxBgOjNWSIMwQ9Mwg70GZBEoKlcByYLbU0tkA27CN/1Nwio8RkY
=21SZ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.17-20220209' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-02-09
this is a pull request of 2 patches for net/master.
Oliver Hartkopp contributes 2 fixes for the CAN ISOTP protocol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a couple of new ioctls for mctp sockets:
SIOCMCTPALLOCTAG and SIOCMCTPDROPTAG. These ioctls provide facilities
for explicit allocation / release of tags, overriding the automatic
allocate-on-send/release-on-reply and timeout behaviours. This allows
userspace more control over messages that may not fit a simple
request/response model.
In order to indicate a pre-allocated tag to the sendmsg() syscall, we
introduce a new flag to the struct sockaddr_mctp.smctp_tag value:
MCTP_TAG_PREALLOC.
Additional changes from Jeremy Kerr <jk@codeconstruct.com.au>.
Contains a fix that was:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we require an exact match on an incoming packet's dest
address, and the key's local_addr field.
In a future change, we may want to set up a key before packets are
routed, meaning we have no local address to match on.
This change allows key lookups to match on local_addr = MCTP_ADDR_ANY.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we have a couple of paths that check that an EID matches, or
the match value is MCTP_ADDR_ANY.
Rather than open coding this, add a little helper.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a few more tests to check the key/tag lookups on route
input. We add a specific entry to the keys lists, route a packet with
specific header values, and check for key match/mismatch.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a definition for the tag-owner flag, which has TO as a standard
abbreviation. We'll want to add a helper for the actual tag value in a
future change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ax25_disconnect() in ax25_kill_by_device() is not
protected by any locks, thus there is a race condition
between ax25_disconnect() and ax25_destroy_socket().
when ax25->sk is assigned as NULL by ax25_destroy_socket(),
a NULL pointer dereference bug will occur if site (1) or (2)
dereferences ax25->sk.
ax25_kill_by_device() | ax25_release()
ax25_disconnect() | ax25_destroy_socket()
... |
if(ax25->sk != NULL) | ...
... | ax25->sk = NULL;
bh_lock_sock(ax25->sk); //(1) | ...
... |
bh_unlock_sock(ax25->sk); //(2)|
This patch moves ax25_disconnect() into lock_sock(), which can
synchronize with ax25_destroy_socket() in ax25_release().
Fail log:
===============================================================
BUG: kernel NULL pointer dereference, address: 0000000000000088
...
RIP: 0010:_raw_spin_lock+0x7e/0xd0
...
Call Trace:
ax25_disconnect+0xf6/0x220
ax25_device_event+0x187/0x250
raw_notifier_call_chain+0x5e/0x70
dev_close_many+0x17d/0x230
rollback_registered_many+0x1f1/0x950
unregister_netdevice_queue+0x133/0x200
unregister_netdev+0x13/0x20
...
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink_dump structure has a union of 'long args[6]' and a context
buffer as scratch space.
Convert ctnetlink to use a structure, its easier to read than the
raw 'args' usage which comes with no type checks and no readable names.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a follow up of the previous patch that enables to get
skb->priority. It's now posssible to set it also.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Florian Westphal <fw@strlen.de>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Allow up to 16-byte comparisons with a new cmp fast version. Use two
64-bit words and calculate the mask representing the bits to be
compared. Make sure the comparison is 64-bit aligned and avoid
out-of-bound memory access on registers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of two exported functions, export a single option structure.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For updating eache missed value we can use cmpxchg.
This also avoids need to disable BH.
kernel robot reported build failure on v1 because not all arches support
cmpxchg for u16, so extend this to u32.
This doesn't increase struct size, existing padding is used.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Calling nf_defrag_ipv4_disable() instead of nf_defrag_ipv6_disable()
was probably not the intent.
I found this by code inspection, while chasing a possible issue in TPROXY.
Fixes: de8c12110a ("netfilter: disable defrag once its no longer needed")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
struct xfrm_user_offload has flags variable that received user input,
but kernel didn't check if valid bits were provided. It caused a situation
where not sanitized input was forwarded directly to the drivers.
For example, XFRM_OFFLOAD_IPV6 define that was exposed, was used by
strongswan, but not implemented in the kernel at all.
As a solution, check and sanitize input flags to forward
XFRM_OFFLOAD_INBOUND to the drivers.
Fixes: d77e38e612 ("xfrm: Add an IPsec hardware offloading API")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Commit 43a08c3bda ("can: isotp: isotp_sendmsg(): fix TX buffer concurrent
access in isotp_sendmsg()") introduced a new locking scheme that may render
the userspace application in a locking state when an error is detected.
This issue shows up under high load on simultaneously running isotp channels
with identical configuration which is against the ISO specification and
therefore breaks any reasonable PDU communication anyway.
Fixes: 43a08c3bda ("can: isotp: isotp_sendmsg(): fix TX buffer concurrent access in isotp_sendmsg()")
Link: https://lore.kernel.org/all/20220209073601.25728-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Cc: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When receiving a CAN frame the current code logic does not consider
concurrently receiving processes which do not show up in real world
usage.
Ziyang Xuan writes:
The following syz problem is one of the scenarios. so->rx.len is
changed by isotp_rcv_ff() during isotp_rcv_cf(), so->rx.len equals
0 before alloc_skb() and equals 4096 after alloc_skb(). That will
trigger skb_over_panic() in skb_put().
=======================================================
CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 5.16.0-rc8-syzkaller #0
RIP: 0010:skb_panic+0x16c/0x16e net/core/skbuff.c:113
Call Trace:
<TASK>
skb_over_panic net/core/skbuff.c:118 [inline]
skb_put.cold+0x24/0x24 net/core/skbuff.c:1990
isotp_rcv_cf net/can/isotp.c:570 [inline]
isotp_rcv+0xa38/0x1e30 net/can/isotp.c:668
deliver net/can/af_can.c:574 [inline]
can_rcv_filter+0x445/0x8d0 net/can/af_can.c:635
can_receive+0x31d/0x580 net/can/af_can.c:665
can_rcv+0x120/0x1c0 net/can/af_can.c:696
__netif_receive_skb_one_core+0x114/0x180 net/core/dev.c:5465
__netif_receive_skb+0x24/0x1b0 net/core/dev.c:5579
Therefore we make sure the state changes and data structures stay
consistent at CAN frame reception time by adding a spin_lock in
isotp_rcv(). This fixes the issue reported by syzkaller but does not
affect real world operation.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/linux-can/d7e69278-d741-c706-65e1-e87623d9a8e8@huawei.com/T/
Link: https://lore.kernel.org/all/20220208200026.13783-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Reported-by: syzbot+4c63f36709a642f801c5@syzkaller.appspotmail.com
Reported-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For some reason default_device_ops kept two exit method:
1) default_device_exit() is called for each netns being dismantled in
a cleanup_net() round. This acquires rtnl for each invocation.
2) default_device_exit_batch() is called once with the list of all netns
int the batch, allowing for a single rtnl invocation.
Get rid of the .exit() method to handle the logic from
default_device_exit_batch(), to decrease the number of rtnl acquisition
to one.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
cleanup_net() is competing with other rtnl users.
Avoiding to acquire rtnl for each netns before calling
cgw_remove_all_jobs() gives chance for cleanup_net()
to progress much faster, holding rtnl a bit longer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
cleanup_net() is competing with other rtnl users.
Avoiding to acquire rtnl for each netns before calling
ipmr_rules_exit() gives chance for cleanup_net()
to progress much faster, holding rtnl a bit longer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
cleanup_net() is competing with other rtnl users.
Avoiding to acquire rtnl for each netns before calling
ip6mr_rules_exit() gives chance for cleanup_net()
to progress much faster, holding rtnl a bit longer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
cleanup_net() is competing with other rtnl users.
fib6_rules_net_exit() seems a good candidate for exit_batch(),
as this gives chance for cleanup_net() to progress much faster,
holding rtnl a bit longer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
cleanup_net() is competing with other rtnl users.
Instead of acquiring rtnl at each fib_net_exit() invocation,
add fib_net_exit_batch() so that rtnl is acquired once.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
cleanup_net() is competing with other rtnl users.
nexthop_net_exit() seems a good candidate for exit_batch(),
as this gives chance for cleanup_net() to progress much faster,
holding rtnl a bit longer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPv6 does not scale very well with the number of IPv6 addresses.
It uses a global (shared by all netns) hash table with 256 buckets.
Some functions like addrconf_verify_rtnl() and addrconf_ifdown()
have to iterate all addresses in the hash table.
I have seen addrconf_verify_rtnl() holding the cpu for 10ms or more.
Switch to the per netns hashtable (and spinlock) added
in prior patches.
This considerably speeds up netns dismantle times on hosts
with thousands of netns. This also has an impact
on regular (fast path) IPv6 processing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Next step for using per netns inet6_addr_lst
is to have per netns work item to ultimately
call addrconf_verify_rtnl() and addrconf_verify()
with a new 'struct net*' argument.
Everything is still using the global inet6_addr_lst[] table.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a per netns hash table and a dedicated spinlock,
first step to get rid of the global inet6_addr_lst[] one.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert one dev_hold()/dev_put() pair in register_netdevice()
and unregister_netdevice_many() to dev_hold_track()
and dev_put_track().
This would allow to detect a rogue dev_put() a bit earlier.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220207184107.1401096-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
->sock can be set to NULL asynchronously unless ->recv_mutex is held.
So it is important to hold that mutex. Otherwise a sysfs read can
trigger an oops.
Commit 17f09d3f61 ("SUNRPC: Check if the xprt is connected before
handling sysfs reads") appears to attempt to fix this problem, but it
only narrows the race window.
Fixes: 17f09d3f61 ("SUNRPC: Check if the xprt is connected before handling sysfs reads")
Fixes: a8482488a7 ("SUNRPC query transport's source port")
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If there are failures then we must not leave the non-NULL pointers with
the error value, otherwise `rpcrdma_ep_destroy` gets confused and tries
free them, resulting in an Oops.
Signed-off-by: Dan Aloni <dan.aloni@vastdata.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Use the new dscp_t type to replace the fa_tos field of fib_alias. This
ensures ECN bits are ignored and makes the field compatible with the
fc_dscp field of struct fib_config.
Converting old *tos variables and fields to dscp_t allows sparse to
flag incorrect uses of DSCP and ECN bits. This patch is entirely about
type annotation and shouldn't change any existing behaviour.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new dscp_t type to replace the fc_tos field of fib_config, to
ensure IPv4 routes aren't influenced by ECN bits when configured with
non-zero rtm_tos.
Before this patch, IPv4 routes specifying an rtm_tos with some of the
ECN bits set were accepted. However they wouldn't work (never match) as
IPv4 normally clears the ECN bits with IPTOS_RT_MASK before doing a FIB
lookup (although a few buggy code paths don't).
After this patch, IPv4 routes specifying an rtm_tos with any ECN bit
set is rejected.
Note: IPv6 routes ignore rtm_tos altogether, any rtm_tos is accepted,
but treated as if it were 0.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new dscp_t type to replace the tos field of struct fib4_rule,
so that fib4-rules consistently ignore ECN bits.
Before this patch, fib4-rules did accept rules with the high order ECN
bit set (but not the low order one). Also, it relied on its callers
masking the ECN bits of ->flowi4_tos to prevent those from influencing
the result. This was brittle and a few call paths still do the lookup
without masking the ECN bits first.
After this patch fib4-rules only compare the DSCP bits. ECN can't
influence the result anymore, even if the caller didn't mask these
bits. Also, fib4-rules now must have both ECN bits cleared or they will
be rejected.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define a dscp_t type and its appropriate helpers that ensure ECN bits
are not taken into account when handling DSCP.
Use this new type to replace the tclass field of struct fib6_rule, so
that fib6-rules don't get influenced by ECN bits anymore.
Before this patch, fib6-rules didn't make any distinction between the
DSCP and ECN bits. Therefore, rules specifying a DSCP (tos or dsfield
options in iproute2) stopped working as soon a packets had at least one
of its ECN bits set (as a work around one could create four rules for
each DSCP value to match, one for each possible ECN value).
After this patch fib6-rules only compare the DSCP bits. ECN doesn't
influence the result anymore. Also, fib6-rules now must have the ECN
bits cleared or they will be rejected.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This place also uses signed min_t and passes this singed int to
copy_to_user (which accepts unsigned argument). I don't think
there is an issue, but let's be consistent.
Fixes: 7855e0db15 ("bpf: test_run: add xdp_shared_info pointer in bpf_test_finish signature")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20220204235849.14658-2-sdf@google.com
My last patch moved the netdev_tracker_alloc() call to a section
protected by a write_lock().
I should have replaced GFP_KERNEL with GFP_ATOMIC to avoid the infamous:
BUG: sleeping function called from invalid context at include/linux/sched/mm.h:256
Fixes: 28f9222138 ("net/smc: fix ref_tracker issue in smc_pnet_add()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in __udp_queue_rcv_skb().
Following new drop reasons are introduced:
SKB_DROP_REASON_SOCKET_RCVBUFF
SKB_DROP_REASON_PROTO_MEM
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in udp_queue_rcv_one_skb().
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in ip_protocol_deliver_rcu().
Following new drop reasons are introduced:
SKB_DROP_REASON_XFRM_POLICY
SKB_DROP_REASON_IP_NOPROTO
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in ip_rcv_finish_core(),
following drop reasons are introduced:
SKB_DROP_REASON_IP_RPFILTER
SKB_DROP_REASON_UNICAST_IN_L2_MULTICAST
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in ip_rcv_core(). Three new
drop reasons are introduced:
SKB_DROP_REASON_OTHERHOST
SKB_DROP_REASON_IP_CSUM
SKB_DROP_REASON_IP_INHDR
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in nf_hook_slow() when
skb is dropped by reason of NF_DROP. Following new drop reasons
are introduced:
SKB_DROP_REASON_NETFILTER_DROP
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing a patch that will follow later
("net: add netns refcount tracker to struct nsproxy")
I found that devtmpfs_init() was called before init_net
was initialized.
This is a bug, because devtmpfs_setup() calls
ksys_unshare(CLONE_NEWNS);
This has the effect of increasing init_net refcount,
which will be later overwritten to 1, as part of setup_net(&init_net)
We had too many prior patches [1] trying to work around the root cause.
Really, make sure init_net is in BSS section, and that net_ns_init()
is called earlier at boot time.
Note that another patch ("vfs: add netns refcount tracker
to struct fs_context") also will need net_ns_init() being called
before vfs_caches_init()
As a bonus, this patch saves around 4KB in .data section.
[1]
f8c46cb390 ("netns: do not call pernet ops for not yet set up init_net namespace")
b5082df801 ("net: Initialise init_net.count to 1")
734b65417b ("net: Statically initialize init_net.dev_base_head")
v2: fixed a build error reported by kernel build bots (CONFIG_NET=n)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, HSR manages mac addresses of known HSR nodes by using list_head.
It takes a lot of time when there are a lot of registered nodes due to
finding specific mac address nodes by using linear search. We can be
reducing the time by using hlist. Thus, this patch moves list_head to
hlist_head for mac addresses and this allows for further improvement of
network performance.
Condition: registered 10,000 known HSR nodes
Before:
# iperf3 -c 192.168.10.1 -i 1 -t 10
Connecting to host 192.168.10.1, port 5201
[ 5] local 192.168.10.2 port 59442 connected to 192.168.10.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.49 sec 3.75 MBytes 21.1 Mbits/sec 0 158 KBytes
[ 5] 1.49-2.05 sec 1.25 MBytes 18.7 Mbits/sec 0 166 KBytes
[ 5] 2.05-3.06 sec 2.44 MBytes 20.3 Mbits/sec 56 16.9 KBytes
[ 5] 3.06-4.08 sec 1.43 MBytes 11.7 Mbits/sec 11 38.0 KBytes
[ 5] 4.08-5.00 sec 951 KBytes 8.49 Mbits/sec 0 56.3 KBytes
After:
# iperf3 -c 192.168.10.1 -i 1 -t 10
Connecting to host 192.168.10.1, port 5201
[ 5] local 192.168.10.2 port 36460 connected to 192.168.10.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 7.39 MBytes 62.0 Mbits/sec 3 130 KBytes
[ 5] 1.00-2.00 sec 5.06 MBytes 42.4 Mbits/sec 16 113 KBytes
[ 5] 2.00-3.00 sec 8.58 MBytes 72.0 Mbits/sec 42 94.3 KBytes
[ 5] 3.00-4.00 sec 7.44 MBytes 62.4 Mbits/sec 2 131 KBytes
[ 5] 4.00-5.07 sec 8.13 MBytes 63.5 Mbits/sec 38 92.9 KBytes
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have plans for increasing MAX_SKB_FRAGS, but sk_msg_sg::copy
is currently an unsigned long, limiting MAX_SKB_FRAGS to 30 on 32bit arches.
Convert it to a bitmap, as Jakub suggested.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are still chasing some syzbot reports where we think a rogue dev_put()
is called with no corresponding prior dev_hold().
Unfortunately it eats a reference on dev->dev_refcnt taken by innocent
dev_hold_track(), meaning that the refcount saturation splat comes
too late to be useful.
Make sure that 'not tracked' dev_put() and dev_hold() better use
CONFIG_NET_DEV_REFCNT_TRACKER=y debug infrastructure:
Prior patch in the series allowed ref_tracker_alloc() and ref_tracker_free()
to be called with a NULL @trackerp parameter, and to use a separate refcount
only to detect too many put() even in the following case:
dev_hold_track(dev, tracker_1, GFP_ATOMIC);
dev_hold(dev);
dev_put(dev);
dev_put(dev); // Should complain loudly here.
dev_put_track(dev, tracker_1); // instead of here
Add clarification about netdev_tracker_alloc() role.
v2: I replaced the dev_put() in linkwatch_do_dev()
with __dev_put() because callers called netdev_tracker_free().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In many cases, ip6mr_sk_done() is called while no ipmr socket
has been registered.
This removes 4 rtnl acquisitions per netns dismantle,
with following callers:
igmp6_net_exit(), tcpv6_net_exit(), ndisc_net_exit()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes minor data-races in ip6_mc_input() and
batadv_mcast_mla_rtr_flags_softif_get_ipv6()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While inspecting some perf report, I noticed that the compiler
emits suboptimal code for the napi CB initialization, fetching
and storing multiple times the memory for flags bitfield.
This is with gcc 10.3.1, but I observed the same with older compiler
versions.
We can help the compiler to do a nicer work clearing several
fields at once using an u32 alias. The generated code is quite
smaller, with the same number of conditional.
Before:
objdump -t net/core/gro.o | grep " F .text"
0000000000000bb0 l F .text 0000000000000357 dev_gro_receive
After:
0000000000000bb0 l F .text 000000000000033c dev_gro_receive
v1 -> v2:
- use struct_group (Alexander and Alex)
RFC -> v1:
- use __struct_group to delimit the zeroed area (Alexander)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 5e10da5385 ("skbuff: allow 'slow_gro' for skb
carring sock reference") and commit af352460b4 ("net: fix GRO
skb truesize update") the truesize of the skb with stolen head is
properly updated by the GRO engine, we don't need anymore resetting
it at recycle time.
v1 -> v2:
- clarify the commit message (Alexander)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tc skb extension is used to send miss info from
tc to ovs datapath module, and driver to tc. For the tc to ovs
miss it is currently always allocated even if it will not
be used by ovs datapath (as it depends on a requested feature).
Export the static key which is used by openvswitch module to
guard this code path as well, so it will be skipped if ovs
datapath doesn't need it. Enable this code path once
ovs datapath needs it.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's illegal to use both port and non-signal flags for adding address.
But it's legal to use both of them for setting flags, which always uses
non-signal flags, backup or fullmesh.
This patch moves this non-signal flag with port check from
mptcp_pm_parse_addr() to mptcp_nl_cmd_add_addr(). Do the check only when
adding addresses, not setting flags or deleting addresses.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the IOAM insertion frequency inside its lwtunnel output
function. This patch introduces a new (atomic) counter for packets,
based on which the algorithm will decide if IOAM should be added or not.
Default frequency is "1/1" (i.e., applied to all packets) for backward
compatibility. The iproute2 patch is ready and will be submitted as soon
as this one is accepted.
Previous iproute2 command:
ip -6 ro ad fc00::1/128 encap ioam6 [ mode ... ] ...
New iproute2 command:
ip -6 ro ad fc00::1/128 encap ioam6 [ freq k/n ] [ mode ... ] ...
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot found that mixing sendpage() and sendmsg(MSG_ZEROCOPY)
calls over the same TCP socket would again trigger the
infamous warning in inet_sock_destruct()
WARN_ON(sk_forward_alloc_get(sk));
While Talal took into account a mix of regular copied data
and MSG_ZEROCOPY one in the same skb, the sendpage() path
has been forgotten.
We want the charging to happen for sendpage(), because
pages could be coming from a pipe. What is missing is the
downgrading of pure zerocopy status to make sure
sk_forward_alloc will stay synced.
Add tcp_downgrade_zcopy_pure() helper so that we can
use it from the two callers.
Fixes: 9b65b17db7 ("net: avoid double accounting for pure zerocopy skbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Talal Ahmad <talalahmad@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20220203225547.665114-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
to avoid checksum or authentication tag mismatches and ensuing session
resets in case the destination buffer isn't guaranteed to be stable.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmH9JWMTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi6GVB/0QZtlzCwL0JVNlF1kro96/Sbyb4kNi
vUgD9L1RLBBDBuGAgVHgIch3E8KxAwTia0BHWH/kxLAV84RqmpcIwuZiAjrqJaoz
9JbXmO47+2/lul6YOrzTLDwWzvoMcv/ngUJYbulD0F6oeVqD9Kl3qUkrpf5cy+mJ
uJpzXDhqrx9A5ruopQRFlx2br1sPp3Jn/45WXejoEUSxnbyKtejK6aZBmatvBgsX
gtfVqSCQeY+bWXkhkg4ZaYAHRqH1lG5we6FEbB0RIG5gY9ygf1w2OWr33S2qrbTg
DKz96jQ4nDAsMpvlis1y0IjpxiAY0c1A0B06E0Xxov/d4fNdtAlnaci5
=pHA5
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.17-rc3' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A patch to make it possible to disable zero copy path in the messenger
to avoid checksum or authentication tag mismatches and ensuing session
resets in case the destination buffer isn't guaranteed to be stable"
* tag 'ceph-for-5.17-rc3' of git://github.com/ceph/ceph-client:
libceph: optionally use bounce buffer on recv path in crc mode
libceph: make recv path in secure mode work the same as send path
My previous fix here to fix the deadlock left a race where
the exact same deadlock (see the original commit referenced
below) can still happen if cfg80211_destroy_ifaces() already
runs while nl80211_netlink_notify() is still marking some
interfaces as nl_owner_dead.
The race happens because we have two loops here - first we
dev_close() all the netdevs, and then we destroy them. If we
also have two netdevs (first one need only be a wdev though)
then we can find one during the first iteration, close it,
and go to the second iteration -- but then find two, and try
to destroy also the one we didn't close yet.
Fix this by only iterating once.
Reported-by: Toke Høiland-Jørgensen <toke@redhat.com>
Fixes: ea6b2098dd ("cfg80211: fix locking in netlink owner interface destruction")
Tested-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20220201130951.22093-1-johannes@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the following coccicheck warnings:
net/mac80211/util.c:3265:3: warning: Value stored to 'channel_type' is
never read [clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220113161557.129427-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We check ieee80211_vif_is_mesh() at the top if() block,
there's no need to check for it again.
Signed-off-by: Baligh Gasmi <gasmibal@gmail.com>
Link: https://lore.kernel.org/r/20220203153035.198697-1-gasmibal@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The size of the status_driver_data field was not adjusted when
the is_valid_ack_signal field was added.
Since the size of struct ieee80211_tx_info is limited, replace
the is_valid_ack_signal field with a flags field, and adjust the
struct size accordingly.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.0ff363d4fa56.I45792c0187034a6d0e1c99a7db741996ef7caba3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We validate that AP has mandatory rates set in HE capabilities.
Also we make sure AP is consistent with itself on rates set in HE basic
rates required joining the BSS and rates set in HE capabilities.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.7023450fdf16.I194df59252097ba25a0a543456d4350f1607a538@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE80211_VHT_MCS_NOT_SUPPORTED and IEEE80211_HE_MCS_NOT_SUPPORTED
have the same value so no real bug, but for code integrity use the
HE macros for parsing HE capabilities.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.e974b7b3b217.I732cc7f770c7fa06e4840adb5d45d7ee99ac8eb5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When adding 6GHz channels to scan request based on reported
co-located APs, don't add channels that have only APs with
"non-transmitted" BSSes if they only match the wildcard SSID since
they will be found by probing the "transmitted" BSS.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.f6ddf099f934.I231e55885d3644f292d00dfe0f42653269f2559e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's currently only one driver that reports CHECKSUM_COMPLETE,
that is iwlwifi. The current hardware there calculates checksum
after the SNAP header, but only RFC 1042 (and some other cases,
but replicating the exact hardware logic for corner cases in the
driver seemed awkward.)
Newer generations of hardware will checksum _including_ the SNAP,
which makes things easier.
To handle that, simply always assume the checksum _includes_ the
SNAP header, which this patch does, requiring to first add it
for older iwlwifi hardware, and then remove it again later on
conversion.
Alternatively, we could have:
1) Always assumed the checksum starts _after_ the SNAP header;
the problem with this is that we'd have to replace the exact
"what is the SNAP" check in iwlwifi that cfg80211 has.
2) Made it configurable with some flag, but that seemed like too
much complexity.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.230736e19e0e.I3e6745873585ad943c152fab9e23b5221f17a95f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In UHB connection we don't have any HT/VHT elemens so in order to
calculate the max RX-NSS we need also to look at HE capa element, this
causes to limit us to max rx nss in UHB to 1.
Also anyway we need to look at HE max rx NSS and not only at HT/VHT
capa to determine the max rx nss over the connection.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.3713e0dea5dd.I3b9a15b4c53465c3f86f35459e9dc15ae4ea2abd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we're limiting bandwidth for some reason such as regulatory
restrictions, then advertise that limitation just like we do
for VHT today, so the AP is aware we cannot use the higher BW
it might be using.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.70c8e3e7ee76.If317630de69ff1146bec7d47f5b83038695eb71d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TLS recvmsg() passes user pages as destination for decrypt.
The decrypt operation is repeated record by record, each
record being 16kB, max. TLS allocates an sg_table and uses
iov_iter_get_pages() to populate it with enough pages to
fit the decrypted record.
Even though we decrypt a single message at a time we size
the sg_table based on the entire length of the iovec.
This leads to unnecessarily large allocations, risking
triggering OOM conditions.
Use iov_iter_truncate() / iov_iter_reexpand() to construct
a "capped" version of iov_iter_npages(). Alternatively we
could parametrize iov_iter_npages() to take the size as
arg instead of using i->count, or do something else..
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to have the datapath call the always-true comment match stub.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This allows to replace a tcp option with nop padding to selectively disable
a particular tcp option.
Optstrip mode is chosen when userspace passes the exthdr expression with
neither a source nor a destination register attribute.
This is identical to xtables TCPOPTSTRIP extension.
The only difference is that TCPOPTSTRIP allows to pass in a bitmap
of options to remove rather than a single number.
Unlike TCPOPTSTRIP this expression can be used multiple times
in the same rule to get the same effect.
We could add a new nested attribute later on in case there is a
use case for single-expression-multi-remove.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of exposing the four hooks individually use a sinle hook ops
structure.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
These no longer register/unregister a meaningful structure so remove it.
Cc: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The nat module already exposes a few functions to the conntrack core.
Move the nat extension destroy hook to it.
After this, no conntrack extension needs a destroy hook.
'struct nf_ct_ext_type' and the register/unregister api can be removed
in a followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
No need to specify this in the registration modules, we already
collect all sizes for build-time checks on the maximum combined size.
After this change, all extensions except nat have no meaningful content
in their nf_ct_ext_type struct definition.
Next patch handles nat, this will then allow to remove the dynamic
register api completely.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All extensions except one need 8 byte alignment, so just make that the
default.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This info could be useful to improve traffic analysis.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The udp_error function verifies the checksum of incoming UDP packets if
one is set. This has the desirable side effect of setting skb->ip_summed
to CHECKSUM_COMPLETE, signalling that this verification need not be
repeated further up the stack.
Conversely, when the UDP checksum is empty, which is perfectly legal (at least
inside IPv4), udp_error previously left no trace that the checksum had been
deemed acceptable.
This was a problem in particular for nf_reject_ipv4, which verifies the
checksum in nf_send_unreach() before sending ICMP_DEST_UNREACH. It makes
no accommodation for zero UDP checksums unless they are already marked
as CHECKSUM_UNNECESSARY.
This commit ensures packets with empty UDP checksum are marked as
CHECKSUM_UNNECESSARY, which is explicitly recommended in skbuff.h.
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When userspace, e.g. conntrackd, inserts an entry with a specified helper,
its possible that the helper is lost immediately after its added:
ctnetlink_create_conntrack
-> nf_ct_helper_ext_add + assign helper
-> ctnetlink_setup_nat
-> ctnetlink_parse_nat_setup
-> parse_nat_setup -> nfnetlink_parse_nat_setup
-> nf_nat_setup_info
-> nf_conntrack_alter_reply
-> __nf_ct_try_assign_helper
... and __nf_ct_try_assign_helper will zero the helper again.
Set IPS_HELPER bit to bypass auto-assign logic, its unwanted, just like
when helper is assigned via ruleset.
Dropped old 'not strictly necessary' comment, it referred to use of
rcu_assign_pointer() before it got replaced by RCU_INIT_POINTER().
NB: Fixes tag intentionally incorrect, this extends the referenced commit,
but this change won't build without IPS_HELPER introduced there.
Fixes: 6714cf5465 ("netfilter: nf_conntrack: fix explicit helper attachment and NAT")
Reported-by: Pham Thanh Tuyen <phamtyn@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
TCP conntrack assumes that a syn-ack retransmit is identical to the
previous syn-ack. This isn't correct and causes stuck 3whs in some more
esoteric scenarios. tcpdump to illustrate the problem:
client > server: Flags [S] seq 1365731894, win 29200, [mss 1460,sackOK,TS val 2083035583 ecr 0,wscale 7]
server > client: Flags [S.] seq 145824453, ack 643160523, win 65535, [mss 8952,wscale 5,TS val 3215367629 ecr 2082921663]
Note the invalid/outdated synack ack number.
Conntrack marks this syn-ack as out-of-window/invalid, but it did
initialize the reply direction parameters based on this packets content.
client > server: Flags [S] seq 1365731894, win 29200, [mss 1460,sackOK,TS val 2083036623 ecr 0,wscale 7]
... retransmit...
server > client: Flags [S.], seq 145824453, ack 643160523, win 65535, [mss 8952,wscale 5,TS val 3215368644 ecr 2082921663]
and another bogus synack. This repeats, then client re-uses for a new
attempt:
client > server: Flags [S], seq 2375731741, win 29200, [mss 1460,sackOK,TS val 2083100223 ecr 0,wscale 7]
server > client: Flags [S.], seq 145824453, ack 643160523, win 65535, [mss 8952,wscale 5,TS val 3215430754 ecr 2082921663]
... but still gets a invalid syn-ack.
This repeats until:
server > client: Flags [S.], seq 145824453, ack 643160523, win 65535, [mss 8952,wscale 5,TS val 3215437785 ecr 2082921663]
server > client: Flags [R.], seq 145824454, ack 643160523, win 65535, [mss 8952,wscale 5,TS val 3215443451 ecr 2082921663]
client > server: Flags [S], seq 2375731741, win 29200, [mss 1460,sackOK,TS val 2083115583 ecr 0,wscale 7]
server > client: Flags [S.], seq 162602410, ack 2375731742, win 65535, [mss 8952,wscale 5,TS val 3215445754 ecr 2083115583]
This syn-ack has the correct ack number, but conntrack flags it as
invalid: The internal state was created from the first syn-ack seen
so the sequence number of the syn-ack is treated as being outside of
the announced window.
Don't assume that retransmitted syn-ack is identical to previous one.
Treat it like the first syn-ack and reinit state.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It seems more readable to use a common helper in the followup fix rather
than copypaste or goto.
No functional change intended. The function is only called for syn-ack
or syn in repy direction in case of simultaneous open.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Loads relative to ->thoff naturally expect that this points to the
transport header, but this is only true if pkt->fragoff == 0.
This has little effect for rulesets with connection tracking/nat because
these enable ip defra. For other rulesets this prevents false matches.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Vivek Thrivikraman reported:
An SCTP server application which is accessed continuously by client
application.
When the session disconnects the client retries to establish a connection.
After restart of SCTP server application the session is not established
because of stale conntrack entry with connection state CLOSED as below.
(removing this entry manually established new connection):
sctp 9 CLOSED src=10.141.189.233 [..] [ASSURED]
Just skip timeout update of closed entries, we don't want them to
stay around forever.
Reported-and-tested-by: Vivek Thrivikraman <vivek.thrivikraman@est.tech>
Closes: https://bugzilla.netfilter.org/show_bug.cgi?id=1579
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
__dev_alloc_name() allocates a private zeroed page,
then sets bits in it while iterating through net devices.
It can use __set_bit() to avoid unnecessary locked operations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220203064609.3242863-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
and ieee802154.
Current release - regressions:
- Partially revert "net/smc: Add netlink net namespace support",
fix uABI breakage
- netfilter:
- nft_ct: fix use after free when attaching zone template
- nft_byteorder: track register operations
Previous releases - regressions:
- ipheth: fix EOVERFLOW in ipheth_rcvbulk_callback
- phy: qca8081: fix speeds lower than 2.5Gb/s
- sched: fix use-after-free in tc_new_tfilter()
Previous releases - always broken:
- tcp: fix mem under-charging with zerocopy sendmsg()
- tcp: add missing tcp_skb_can_collapse() test in tcp_shift_skb_data()
- neigh: do not trigger immediate probes on NUD_FAILED from
neigh_managed_work, avoid a deadlock
- bpf: use VM_MAP instead of VM_ALLOC for ringbuf, avoid KASAN
false-positives
- netfilter: nft_reject_bridge: fix for missing reply from prerouting
- smc: forward wakeup to smc socket waitqueue after fallback
- ieee802154:
- return meaningful error codes from the netlink helpers
- mcr20a: fix lifs/sifs periods
- at86rf230, ca8210: stop leaking skbs on error paths
- macsec: add missing un-offload call for NETDEV_UNREGISTER of parent
- ax25: add refcount in ax25_dev to avoid UAF bugs
- eth: mlx5e:
- fix SFP module EEPROM query
- fix broken SKB allocation in HW-GRO
- IPsec offload: fix tunnel mode crypto for non-TCP/UDP flows
- eth: amd-xgbe:
- fix skb data length underflow
- ensure reset of the tx_timer_active flag, avoid Tx timeouts
- eth: stmmac: fix runtime pm use in stmmac_dvr_remove()
- eth: e1000e: handshake with CSME starts from Alder Lake platforms
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=qKvf
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, netfilter, and ieee802154.
Current release - regressions:
- Partially revert "net/smc: Add netlink net namespace support", fix
uABI breakage
- netfilter:
- nft_ct: fix use after free when attaching zone template
- nft_byteorder: track register operations
Previous releases - regressions:
- ipheth: fix EOVERFLOW in ipheth_rcvbulk_callback
- phy: qca8081: fix speeds lower than 2.5Gb/s
- sched: fix use-after-free in tc_new_tfilter()
Previous releases - always broken:
- tcp: fix mem under-charging with zerocopy sendmsg()
- tcp: add missing tcp_skb_can_collapse() test in
tcp_shift_skb_data()
- neigh: do not trigger immediate probes on NUD_FAILED from
neigh_managed_work, avoid a deadlock
- bpf: use VM_MAP instead of VM_ALLOC for ringbuf, avoid KASAN
false-positives
- netfilter: nft_reject_bridge: fix for missing reply from prerouting
- smc: forward wakeup to smc socket waitqueue after fallback
- ieee802154:
- return meaningful error codes from the netlink helpers
- mcr20a: fix lifs/sifs periods
- at86rf230, ca8210: stop leaking skbs on error paths
- macsec: add missing un-offload call for NETDEV_UNREGISTER of parent
- ax25: add refcount in ax25_dev to avoid UAF bugs
- eth: mlx5e:
- fix SFP module EEPROM query
- fix broken SKB allocation in HW-GRO
- IPsec offload: fix tunnel mode crypto for non-TCP/UDP flows
- eth: amd-xgbe:
- fix skb data length underflow
- ensure reset of the tx_timer_active flag, avoid Tx timeouts
- eth: stmmac: fix runtime pm use in stmmac_dvr_remove()
- eth: e1000e: handshake with CSME starts from Alder Lake platforms"
* tag 'net-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
ax25: fix reference count leaks of ax25_dev
net: stmmac: ensure PTP time register reads are consistent
net: ipa: request IPA register values be retained
dt-bindings: net: qcom,ipa: add optional qcom,qmp property
tools/resolve_btfids: Do not print any commands when building silently
bpf: Use VM_MAP instead of VM_ALLOC for ringbuf
net, neigh: Do not trigger immediate probes on NUD_FAILED from neigh_managed_work
tcp: add missing tcp_skb_can_collapse() test in tcp_shift_skb_data()
net: sparx5: do not refer to skb after passing it on
Partially revert "net/smc: Add netlink net namespace support"
net/mlx5e: Avoid field-overflowing memcpy()
net/mlx5e: Use struct_group() for memcpy() region
net/mlx5e: Avoid implicit modify hdr for decap drop rule
net/mlx5e: IPsec: Fix tunnel mode crypto offload for non TCP/UDP traffic
net/mlx5e: IPsec: Fix crypto offload for non TCP/UDP encapsulated traffic
net/mlx5e: Don't treat small ceil values as unlimited in HTB offload
net/mlx5: E-Switch, Fix uninitialized variable modact
net/mlx5e: Fix handling of wrong devices during bond netevent
net/mlx5e: Fix broken SKB allocation in HW-GRO
net/mlx5e: Fix wrong calculation of header index in HW_GRO
...
The previous commit d01ffb9eee ("ax25: add refcount in ax25_dev
to avoid UAF bugs") introduces refcount into ax25_dev, but there
are reference leak paths in ax25_ctl_ioctl(), ax25_fwd_ioctl(),
ax25_rt_add(), ax25_rt_del() and ax25_rt_opt().
This patch uses ax25_dev_put() and adjusts the position of
ax25_addr_ax25dev() to fix reference cout leaks of ax25_dev.
Fixes: d01ffb9eee ("ax25: add refcount in ax25_dev to avoid UAF bugs")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220203150811.42256-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change is meant to permit a driver to perform "fragmenting" of the
page from within the driver instead of the current model which requires
pre-partitioning the page. The main motivation behind this is to support
use cases where the page will be split up by the driver after DMA instead
of before.
With this change it becomes possible to start using page pool to replace
some of the existing use cases where multiple references were being used
for a single page, but the number needed was unknown as the size could be
dynamic.
For example, with this code it would be possible to do something like
the following to handle allocation:
page = page_pool_alloc_pages();
if (!page)
return NULL;
page_pool_fragment_page(page, DRIVER_PAGECNT_BIAS_MAX);
rx_buf->page = page;
rx_buf->pagecnt_bias = DRIVER_PAGECNT_BIAS_MAX;
Then we would process a received buffer by handling it with:
rx_buf->pagecnt_bias--;
Once the page has been fully consumed we could then flush the remaining
instances with:
if (page_pool_defrag_page(page, rx_buf->pagecnt_bias))
continue;
page_pool_put_defragged_page(pool, page -1, !!budget);
The general idea is that we want to have the ability to allocate a page
with excess fragment count and then trim off the unneeded fragments.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added the fullmesh flag setting support in pm_netlink.
If the fullmesh flag of the address is changed, remove all the related
subflows, update the fullmesh flag and create subflows again.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch printed out the reset infos, reset_transient and reset_reason,
of MP_RST in mptcp_parse_option() to show that MP_RST is received.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC8684 doesn't seem to clearly specify which MPTCP options can be used
together.
Some options are mutually exclusive -- e.g. MP_CAPABLE and MP_JOIN --,
some can be used together -- e.g. DSS + MP_PRIO --, some can but we
prefer not to -- e.g. DSS + ADD_ADDR -- and some have to be used
together at some points -- e.g. MP_FAIL and DSS.
We need to clarify this as a base before allowing other modifications.
For example, does it make sense to send a RM_ADDR with an MPC or MPJ?
This remains open for possible future discussions.
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MP_FAIL should be use in very rare cases, either when the TCP RST flag
is set -- with or without an MP_RST -- or with a DSS, see
mptcp_established_options().
Here, we do the same in mptcp_write_options().
Co-developed-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the declarations of ssk and subflow in MP_FAIL and MP_PRIO to the
beginning of the function mptcp_write_options().
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if_id will be always 0, because it was not yet initialized.
Fixes: 8dce439195 ("xfrm: interface with if_id 0 should return error")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
syzkaller was able to trigger a deadlock for NTF_MANAGED entries [0]:
kworker/0:16/14617 is trying to acquire lock:
ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652
[...]
but task is already holding lock:
ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: neigh_managed_work+0x35/0x250 net/core/neighbour.c:1572
The neighbor entry turned to NUD_FAILED state, where __neigh_event_send()
triggered an immediate probe as per commit cd28ca0a3d ("neigh: reduce
arp latency") via neigh_probe() given table lock was held.
One option to fix this situation is to defer the neigh_probe() back to
the neigh_timer_handler() similarly as pre cd28ca0a3d. For the case
of NTF_MANAGED, this deferral is acceptable given this only happens on
actual failure state and regular / expected state is NUD_VALID with the
entry already present.
The fix adds a parameter to __neigh_event_send() in order to communicate
whether immediate probe is allowed or disallowed. Existing call-sites
of neigh_event_send() default as-is to immediate probe. However, the
neigh_managed_work() disables it via use of neigh_event_send_probe().
[0] <TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_deadlock_bug kernel/locking/lockdep.c:2956 [inline]
check_deadlock kernel/locking/lockdep.c:2999 [inline]
validate_chain kernel/locking/lockdep.c:3788 [inline]
__lock_acquire.cold+0x149/0x3ab kernel/locking/lockdep.c:5027
lock_acquire kernel/locking/lockdep.c:5639 [inline]
lock_acquire+0x1ab/0x510 kernel/locking/lockdep.c:5604
__raw_write_lock_bh include/linux/rwlock_api_smp.h:202 [inline]
_raw_write_lock_bh+0x2f/0x40 kernel/locking/spinlock.c:334
___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652
ip6_finish_output2+0x1070/0x14f0 net/ipv6/ip6_output.c:123
__ip6_finish_output net/ipv6/ip6_output.c:191 [inline]
__ip6_finish_output+0x61e/0xe90 net/ipv6/ip6_output.c:170
ip6_finish_output+0x32/0x200 net/ipv6/ip6_output.c:201
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:224
dst_output include/net/dst.h:451 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
ndisc_send_skb+0xa99/0x17f0 net/ipv6/ndisc.c:508
ndisc_send_ns+0x3a9/0x840 net/ipv6/ndisc.c:650
ndisc_solicit+0x2cd/0x4f0 net/ipv6/ndisc.c:742
neigh_probe+0xc2/0x110 net/core/neighbour.c:1040
__neigh_event_send+0x37d/0x1570 net/core/neighbour.c:1201
neigh_event_send include/net/neighbour.h:470 [inline]
neigh_managed_work+0x162/0x250 net/core/neighbour.c:1574
process_one_work+0x9ac/0x1650 kernel/workqueue.c:2307
worker_thread+0x657/0x1110 kernel/workqueue.c:2454
kthread+0x2e9/0x3a0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
Fixes: 7482e3841d ("net, neigh: Add NTF_MANAGED flag for managed neighbor entries")
Reported-by: syzbot+5239d0e1778a500d477a@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Tested-by: syzbot+5239d0e1778a500d477a@syzkaller.appspotmail.com
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220201193942.5055-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_shift_skb_data() might collapse three packets into a larger one.
P_A, P_B, P_C -> P_ABC
Historically, it used a single tcp_skb_can_collapse_to(P_A) call,
because it was enough.
In commit 8571248411 ("tcp: coalesce/collapse must respect MPTCP extensions"),
this call was replaced by a call to tcp_skb_can_collapse(P_A, P_B)
But the now needed test over P_C has been missed.
This probably broke MPTCP.
Then later, commit 9b65b17db7 ("net: avoid double accounting for pure zerocopy skbs")
added an extra condition to tcp_skb_can_collapse(), but the missing call
from tcp_shift_skb_data() is also breaking TCP zerocopy, because P_A and P_C
might have different skb_zcopy_pure() status.
Fixes: 8571248411 ("tcp: coalesce/collapse must respect MPTCP extensions")
Fixes: 9b65b17db7 ("net: avoid double accounting for pure zerocopy skbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Cc: Talal Ahmad <talalahmad@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220201184640.756716-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both msgr1 and msgr2 in crc mode are zero copy in the sense that
message data is read from the socket directly into the destination
buffer. We assume that the destination buffer is stable (i.e. remains
unchanged while it is being read to) though. Otherwise, CRC errors
ensue:
libceph: read_partial_message 0000000048edf8ad data crc 1063286393 != exp. 228122706
libceph: osd1 (1)192.168.122.1:6843 bad crc/signature
libceph: bad data crc, calculated 57958023, expected 1805382778
libceph: osd2 (2)192.168.122.1:6876 integrity error, bad crc
Introduce rxbounce option to enable use of a bounce buffer when
receiving message data. In particular this is needed if a mapped
image is a Windows VM disk, passed to QEMU. Windows has a system-wide
"dummy" page that may be mapped into the destination buffer (potentially
more than once into the same buffer) by the Windows Memory Manager in
an effort to generate a single large I/O [1][2]. QEMU makes a point of
preserving overlap relationships when cloning I/O vectors, so krbd gets
exposed to this behaviour.
[1] "What Is Really in That MDL?"
https://docs.microsoft.com/en-us/previous-versions/windows/hardware/design/dn614012(v=vs.85)
[2] https://blogs.msmvps.com/kernelmustard/2005/05/04/dummy-pages/
URL: https://bugzilla.redhat.com/show_bug.cgi?id=1973317
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
The recv path of secure mode is intertwined with that of crc mode.
While it's slightly more efficient that way (the ciphertext is read
into the destination buffer and decrypted in place, thus avoiding
two potentially heavy memory allocations for the bounce buffer and
the corresponding sg array), it isn't really amenable to changes.
Sacrifice that edge and align with the send path which always uses
a full-sized bounce buffer (currently there is no other way -- if
the kernel crypto API ever grows support for streaming (piecewise)
en/decryption for GCM [1], we would be able to easily take advantage
of that on both sides).
[1] https://lore.kernel.org/all/20141225202830.GA18794@gondor.apana.org.au/
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
The change of sizeof(struct smc_diag_linkinfo) by commit 79d39fc503
("net/smc: Add netlink net namespace support") introduced an ABI
regression: since struct smc_diag_lgrinfo contains an object of
type "struct smc_diag_linkinfo", offset of all subsequent members
of struct smc_diag_lgrinfo was changed by that change.
As result, applications compiled with the old version
of struct smc_diag_linkinfo will receive garbage in
struct smc_diag_lgrinfo.role if the kernel implements
this new version of struct smc_diag_linkinfo.
Fix this regression by reverting the part of commit 79d39fc503 that
changes struct smc_diag_linkinfo. After all, there is SMC_GEN_NETLINK
interface which is good enough, so there is probably no need to touch
the smc_diag ABI in the first place.
Fixes: 79d39fc503 ("net/smc: Add netlink net namespace support")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20220202030904.GA9742@altlinux.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When setting RTO through BPF program, some SYN ACK packets were unaffected
and continued to use TCP_TIMEOUT_INIT constant. This patch adds timeout
option to struct request_sock. Option is initialized with TCP_TIMEOUT_INIT
and is reassigned through BPF using tcp_timeout_init call. SYN ACK
retransmits now use newly added timeout option.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Acked-by: Martin KaFai Lau <kafai@fb.com>
v2:
- Add timeout option to struct request_sock. Do not call
tcp_timeout_init on every syn ack retransmit.
v3:
- Use unsigned long for min. Bound tcp_timeout_init to TCP_RTO_MAX.
v4:
- Refactor duplicate code by adding reqsk_timeout function.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add connect/disconnect helper to assign private struct to the DSA switch.
Add support for Ethernet mgmt and MIB if the DSA driver provide an handler
to correctly parse and elaborate the data.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add struct to correctly parse a mib Ethernet packet.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add all the required define to prepare support for mgmt read/write in
Ethernet packet. Any packet of this type has to be dropped as the only
use of these special packet is receive ack for an mgmt write request or
receive data for an mgmt read request.
A struct is used that emulates the Ethernet header but is used for a
different purpose.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet MDIO packets are non-standard and DSA master expects the first
6 octets to be the MAC DA. To address these kind of packet, enable
promisc_on_master flag for the tagger.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move tag_qca define to include dir linux/dsa as the qca8k require access
to the tagger define to support in-band mdio read/write using ethernet
packet.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to FIELD macro to drop redundant define.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for switch driver to be able to make simple and reliable use of
the master tracking operations, they must also be notified of the
initial state of the DSA master, not just of the changes. This is
because they might enable certain features only during the time when
they know that the DSA master is up and running.
Therefore, this change explicitly checks the state of the DSA master
under the same rtnl_mutex as we were holding during the
dsa_master_setup() and dsa_master_teardown() call. The idea being that
if the DSA master became operational in between the moment in which it
became a DSA master (dsa_master_setup set dev->dsa_ptr) and the moment
when we checked for the master being up, there is a chance that we
would emit a ->master_state_change() call with no actual state change.
We need to avoid that by serializing the concurrent netdevice event with
us. If the netdevice event started before, we force it to finish before
we begin, because we take rtnl_lock before making netdev_uses_dsa()
return true. So we also handle that early event and do nothing on it.
Similarly, if the dev_open() attempt is concurrent with us, it will
attempt to take the rtnl_mutex, but we're holding it. We'll see that
the master flag IFF_UP isn't set, then when we release the rtnl_mutex
we'll process the NETDEV_UP notifier.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain drivers may need to send management traffic to the switch for
things like register access, FDB dump, etc, to accelerate what their
slow bus (SPI, I2C, MDIO) can already do.
Ethernet is faster (especially in bulk transactions) but is also more
unreliable, since the user may decide to bring the DSA master down (or
not bring it up), therefore severing the link between the host and the
attached switch.
Drivers needing Ethernet-based register access already should have
fallback logic to the slow bus if the Ethernet method fails, but that
fallback may be based on a timeout, and the I/O to the switch may slow
down to a halt if the master is down, because every Ethernet packet will
have to time out. The driver also doesn't have the option to turn off
Ethernet-based I/O momentarily, because it wouldn't know when to turn it
back on.
Which is where this change comes in. By tracking NETDEV_CHANGE,
NETDEV_UP and NETDEV_GOING_DOWN events on the DSA master, we should know
the exact interval of time during which this interface is reliably
available for traffic. Provide this information to switches so they can
use it as they wish.
An helper is added dsa_port_master_is_operational() to check if a master
port is operational.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xfrm_dev_register() and xfrm_dev_feat_change() have same
implementation of one call to xfrm_api_check(). Instead of doing such
indirection, call to xfrm_api_check() directly and delete duplicated
functions.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We got reports of following warning in inet_sock_destruct()
WARN_ON(sk_forward_alloc_get(sk));
Whenever we add a non zero-copy fragment to a pure zerocopy skb,
we have to anticipate that whole skb->truesize will be uncharged
when skb is finally freed.
skb->data_len is the payload length. But the memory truesize
estimated by __zerocopy_sg_from_iter() is page aligned.
Fixes: 9b65b17db7 ("net: avoid double accounting for pure zerocopy skbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Talal Ahmad <talalahmad@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20220201065254.680532-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When packet_setsockopt( PACKET_FANOUT_DATA ) reads po->fanout,
no lock is held, meaning that another thread can change po->fanout.
Given that po->fanout can only be set once during the socket lifetime
(it is only cleared from fanout_release()), we can use
READ_ONCE()/WRITE_ONCE() to document the race.
BUG: KCSAN: data-race in packet_setsockopt / packet_setsockopt
write to 0xffff88813ae8e300 of 8 bytes by task 14653 on cpu 0:
fanout_add net/packet/af_packet.c:1791 [inline]
packet_setsockopt+0x22fe/0x24a0 net/packet/af_packet.c:3931
__sys_setsockopt+0x209/0x2a0 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88813ae8e300 of 8 bytes by task 14654 on cpu 1:
packet_setsockopt+0x691/0x24a0 net/packet/af_packet.c:3935
__sys_setsockopt+0x209/0x2a0 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000000000000000 -> 0xffff888106f8c000
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 14654 Comm: syz-executor.3 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 47dceb8ecd ("packet: add classic BPF fanout mode")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220201022358.330621-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While looking at one unrelated syzbot bug, I found the replay logic
in __rtnl_newlink() to potentially trigger use-after-free.
It is better to clear master_dev and m_ops inside the loop,
in case we have to replay it.
Fixes: ba7d49b1f0 ("rtnetlink: provide api for getting and setting slave info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20220201012106.216495-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's not reason SO_MARK would be allowed via setsockopt()
and not via cmsg, let's keep the two consistent. See
commit 079925cce1 ("net: allow SO_MARK with CAP_NET_RAW")
for justification why NET_RAW -> SO_MARK is safe.
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220131233357.52964-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Menglong Dong reports that the documentation for the dst_port field in
struct bpf_sock is inaccurate and confusing. From the BPF program PoV, the
field is a zero-padded 16-bit integer in network byte order. The value
appears to the BPF user as if laid out in memory as so:
offsetof(struct bpf_sock, dst_port) + 0 <port MSB>
+ 8 <port LSB>
+16 0x00
+24 0x00
32-, 16-, and 8-bit wide loads from the field are all allowed, but only if
the offset into the field is 0.
32-bit wide loads from dst_port are especially confusing. The loaded value,
after converting to host byte order with bpf_ntohl(dst_port), contains the
port number in the upper 16-bits.
Remove the confusion by splitting the field into two 16-bit fields. For
backward compatibility, allow 32-bit wide loads from offsetof(struct
bpf_sock, dst_port).
While at it, allow loads 8-bit loads at offset [0] and [1] from dst_port.
Reported-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/r/20220130115518.213259-2-jakub@cloudflare.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This introduces a new corked flag, MSG_SENDPAGE_NOTLAST, which is
involved in syscall sendfile() [1], it indicates this is not the last
page. So we can cork the data until the page is not specify this flag.
It has the same effect as MSG_MORE, but existed in sendfile() only.
This patch adds a option MSG_SENDPAGE_NOTLAST for corking data, try to
cork more data before sending when using sendfile(), which acts like
TCP's behaviour. Also, this reimplements the default sendpage to inform
that it is supported to some extent.
[1] https://man7.org/linux/man-pages/man2/sendfile.2.html
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the manual of TCP_CORK [1] and MSG_MORE [2], these two options
have the same effect. Applications can set these options and informs the
kernel to pend the data, and send them out only when the socket or
syscall does not specify this flag. In other words, there's no need to
send data out by a delayed work, which will queue a lot of work.
This removes corked delayed work with SMC_TX_CORK_DELAY (250ms), and the
applications control how/when to send them out. It improves the
performance for sendfile and throughput, and remove unnecessary race of
lock_sock(). This also unlocks the limitation of sndbuf, and try to fill
it up before sending.
[1] https://linux.die.net/man/7/tcp
[2] https://man7.org/linux/man-pages/man2/send.2.html
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the man page of TCP_CORK [1], if set, don't send out
partial frames. All queued partial frames are sent when option is
cleared again.
When applications call setsockopt to disable TCP_CORK, this call is
protected by lock_sock(), and tries to mod_delayed_work() to 0, in order
to send pending data right now. However, the delayed work smc_tx_work is
also protected by lock_sock(). There introduces lock contention for
sending data.
To fix it, send pending data directly which acts like TCP, without
lock_sock() protected in the context of setsockopt (already lock_sock()ed),
and cancel unnecessary dealyed work, which is protected by lock.
[1] https://linux.die.net/man/7/tcp
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling rehash behavior did not affect SYN ACK retransmits because hash
was forcefully changed bypassing the sk_rethink_hash function. This patch
adds a condition which checks for rehash mode before resetting hash.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bpf socket option to override rehash behaviour from userspace or from bpf.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SO_TXREHASH socket option to control hash rethink behavior per socket.
When default mode is set, sockets disable rehash at initialization and use
sysctl option when entering listen state. setsockopt() overrides default
behavior.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a per ns sysctl that controls the txhash rethink behavior:
net.core.txrehash. When enabled, the same behavior is retained,
when disabled, rethink is not performed. Sysctl is enabled by default.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the possible failure of the alloc, the ifmgd->assoc_req_ies might be
NULL pointer returned from kmemdup().
Therefore it might be better to free the skb and return error in order
to fail the association, like ieee80211_assoc_success().
Also, the caller, ieee80211_do_assoc(), needs to deal with the return
value from ieee80211_send_assoc().
Fixes: 4d9ec73d2b ("cfg80211: Report Association Request frame IEs in association events")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220105081559.2387083-1-jiasheng@iscas.ac.cn
[fix some paths to be errors, not success]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ip_idents_reserve is only used in net/ipv4/route.c. Make it static
and remove the export.
Signed-off-by: David Ahern <dsahern@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we replace TCP with SMC and a fallback occurs, there may be
some socket waitqueue entries remaining in smc socket->wq, such
as eppoll_entries inserted by userspace applications.
After the fallback, data flows over TCP/IP and only clcsocket->wq
will be woken up. Applications can't be notified by the entries
which were inserted in smc socket->wq before fallback. So we need
a mechanism to wake up smc socket->wq at the same time if some
entries remaining in it.
The current workaround is to transfer the entries from smc socket->wq
to clcsock->wq during the fallback. But this may cause a crash
like this:
general protection fault, probably for non-canonical address 0xdead000000000100: 0000 [#1] PREEMPT SMP PTI
CPU: 3 PID: 0 Comm: swapper/3 Kdump: loaded Tainted: G E 5.16.0+ #107
RIP: 0010:__wake_up_common+0x65/0x170
Call Trace:
<IRQ>
__wake_up_common_lock+0x7a/0xc0
sock_def_readable+0x3c/0x70
tcp_data_queue+0x4a7/0xc40
tcp_rcv_established+0x32f/0x660
? sk_filter_trim_cap+0xcb/0x2e0
tcp_v4_do_rcv+0x10b/0x260
tcp_v4_rcv+0xd2a/0xde0
ip_protocol_deliver_rcu+0x3b/0x1d0
ip_local_deliver_finish+0x54/0x60
ip_local_deliver+0x6a/0x110
? tcp_v4_early_demux+0xa2/0x140
? tcp_v4_early_demux+0x10d/0x140
ip_sublist_rcv_finish+0x49/0x60
ip_sublist_rcv+0x19d/0x230
ip_list_rcv+0x13e/0x170
__netif_receive_skb_list_core+0x1c2/0x240
netif_receive_skb_list_internal+0x1e6/0x320
napi_complete_done+0x11d/0x190
mlx5e_napi_poll+0x163/0x6b0 [mlx5_core]
__napi_poll+0x3c/0x1b0
net_rx_action+0x27c/0x300
__do_softirq+0x114/0x2d2
irq_exit_rcu+0xb4/0xe0
common_interrupt+0xba/0xe0
</IRQ>
<TASK>
The crash is caused by privately transferring waitqueue entries from
smc socket->wq to clcsock->wq. The owners of these entries, such as
epoll, have no idea that the entries have been transferred to a
different socket wait queue and still use original waitqueue spinlock
(smc socket->wq.wait.lock) to make the entries operation exclusive,
but it doesn't work. The operations to the entries, such as removing
from the waitqueue (now is clcsock->wq after fallback), may cause a
crash when clcsock waitqueue is being iterated over at the moment.
This patch tries to fix this by no longer transferring wait queue
entries privately, but introducing own implementations of clcsock's
callback functions in fallback situation. The callback functions will
forward the wakeup to smc socket->wq if clcsock->wq is actually woken
up and smc socket->wq has remaining entries.
Fixes: 2153bd1e3d ("net/smc: Transfer remaining wait queue entries during fallback")
Suggested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since v2.5.44 and addition of ip_options_fragment()
ip_options_build() does not render headers for fragments
directly. @is_frag is always 0.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add support for RTL8822C hci_ver 0x08
- Add support for RTL8852AE part 0bda:2852
- Fix WBS setting for Intel legacy ROM products
- Enable SCO over I2S ib mt7921s
- Increment management interface revision
-----BEGIN PGP SIGNATURE-----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=/KS7
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2022-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for RTL8822C hci_ver 0x08
- Add support for RTL8852AE part 0bda:2852
- Fix WBS setting for Intel legacy ROM products
- Enable SCO over I2S ib mt7921s
- Increment management interface revision
* tag 'for-net-next-2022-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (30 commits)
Bluetooth: Increment management interface revision
Bluetooth: hci_sync: Fix queuing commands when HCI_UNREGISTER is set
Bluetooth: hci_h5: Add power reset via gpio in h5_btrtl_open
Bluetooth: btrtl: Add support for RTL8822C hci_ver 0x08
Bluetooth: hci_event: Fix HCI_EV_VENDOR max_len
Bluetooth: hci_core: Rate limit the logging of invalid SCO handle
Bluetooth: hci_event: Ignore multiple conn complete events
Bluetooth: msft: fix null pointer deref on msft_monitor_device_evt
Bluetooth: btmtksdio: mask out interrupt status
Bluetooth: btmtksdio: run sleep mode by default
Bluetooth: btmtksdio: lower log level in btmtksdio_runtime_[resume|suspend]()
Bluetooth: mt7921s: fix btmtksdio_[drv|fw]_pmctrl()
Bluetooth: mt7921s: fix bus hang with wrong privilege
Bluetooth: btmtksdio: refactor btmtksdio_runtime_[suspend|resume]()
Bluetooth: mt7921s: fix firmware coredump retrieve
Bluetooth: hci_serdev: call init_rwsem() before p->open()
Bluetooth: Remove kernel-doc style comment block
Bluetooth: btusb: Whitespace fixes for btusb_setup_csr()
Bluetooth: btusb: Add one more Bluetooth part for the Realtek RTL8852AE
Bluetooth: btintel: Fix WBS setting for Intel legacy ROM products
...
====================
Link: https://lore.kernel.org/r/20220128205915.3995760-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmHz0QsACgkQnJ2qBz9k
QNkN+AgA6XqWHKYyElfgJFt1UqaoNMz/Faz9H/+PKiBNSTf6/+67D+V7DFz6jJrv
dDwHNzfDg9kR+pbAAPwhl2jfnQoUlsr019Hrqa5HpWlj5geVpbdunYUzS2WOkwqD
/m+brcLgPdKb2uIysj6wOh9B7wa8V9ksl3EjQvvwaHaU0p1YLUqidVXucYvs8DUo
bgXNaj9GmeysxnmU+aILotWuuXH2vOP4Q2Uk4qz3rN6xW9eEXtpQ4y7gWBp/GA8y
Ia8FtFdQdvlSDOJYMdPOTBu5RB7gY9ElrapvVaWNYtCWI/jRv666nZsLaERYNhLN
uUsG4MWjYbOqW5XqFDbSOwbDqvMh5Q==
=mEFA
-----END PGP SIGNATURE-----
Merge tag 'fsnotify_for_v5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fsnotify fixes from Jan Kara:
"Fixes for userspace breakage caused by fsnotify changes ~3 years ago
and one fanotify cleanup"
* tag 'fsnotify_for_v5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fsnotify: fix fsnotify hooks in pseudo filesystems
fsnotify: invalidate dcache before IN_DELETE event
fanotify: remove variable set but not used
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2022-01-28
An update from ieee802154 for your *net* tree.
A bunch of fixes in drivers, all from Miquel Raynal.
Clarifying the default channel in hwsim, leak fixes in at86rf230 and ca8210 as
well as a symbol duration fix for mcr20a. Topping up the driver fixes with
better error codes in nl802154 and a cleanup in MAINTAINERS for an orphaned
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If we dereference ax25_dev after we call kfree(ax25_dev) in
ax25_dev_device_down(), it will lead to concurrency UAF bugs.
There are eight syscall functions suffer from UAF bugs, include
ax25_bind(), ax25_release(), ax25_connect(), ax25_ioctl(),
ax25_getname(), ax25_sendmsg(), ax25_getsockopt() and
ax25_info_show().
One of the concurrency UAF can be shown as below:
(USE) | (FREE)
| ax25_device_event
| ax25_dev_device_down
ax25_bind | ...
... | kfree(ax25_dev)
ax25_fillin_cb() | ...
ax25_fillin_cb_from_dev() |
... |
The root cause of UAF bugs is that kfree(ax25_dev) in
ax25_dev_device_down() is not protected by any locks.
When ax25_dev, which there are still pointers point to,
is released, the concurrency UAF bug will happen.
This patch introduces refcount into ax25_dev in order to
guarantee that there are no pointers point to it when ax25_dev
is released.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit 1ade48d0c2 ("ax25: NPD bug when detaching
AX25 device") introduce lock_sock() into ax25_kill_by_device to
prevent NPD bug. But the concurrency NPD or UAF bug will occur,
when lock_sock() or release_sock() dereferences the ax25_cb->sock.
The NULL pointer dereference bug can be shown as below:
ax25_kill_by_device() | ax25_release()
| ax25_destroy_socket()
| ax25_cb_del()
... | ...
| ax25->sk=NULL;
lock_sock(s->sk); //(1) |
s->ax25_dev = NULL; | ...
release_sock(s->sk); //(2) |
... |
The root cause is that the sock is set to null before dereference
site (1) or (2). Therefore, this patch extracts the ax25_cb->sock
in advance, and uses ax25_list_lock to protect it, which can synchronize
with ax25_cb_del() and ensure the value of sock is not null before
dereference sites.
The concurrency UAF bug can be shown as below:
ax25_kill_by_device() | ax25_release()
| ax25_destroy_socket()
... | ...
| sock_put(sk); //FREE
lock_sock(s->sk); //(1) |
s->ax25_dev = NULL; | ...
release_sock(s->sk); //(2) |
... |
The root cause is that the sock is released before dereference
site (1) or (2). Therefore, this patch uses sock_hold() to increase
the refcount of sock and uses ax25_list_lock to protect it, which
can synchronize with ax25_cb_del() in ax25_destroy_socket() and
ensure the sock wil not be released before dereference sites.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct svc_xprt holds a long lived reference to a netns,
it is worth tracking it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For applications running on a mix of platforms it's useful
to have a clear indication whether host's NIC supports the
geometry requirements of TCP zero-copy. TCP zero-copy Rx
requires data to be neatly placed into memory pages.
Most NICs can't do that.
This patch is adding GET support only, since the NICs
I work with either always have the feature enabled or
enable it whenever MTU is set to jumbo. In other words
I don't need SET. But adding set should be trivial.
(The only note on SET is that we will likely want
the setting to be "sticky" and use 0 / `unknown`
to reset it back to driver default.)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This define already exist but is hardcoded in nl-phy.c. Use the
definition when relevant.
While at it, also convert the type from uint32_t to u32.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125122540.855604-3-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Inline a part of ipv6_fixup_options() to avoid extra overhead on
function call if opt is NULL.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
udpv6_sendmsg() doesn't need dst after calling ip6_make_skb(), so
instead of taking an additional reference inside ip6_setup_cork()
and releasing the initial one afterwards, we can hand over a reference
into ip6_make_skb() saving two atomics. The only other user of
ip6_setup_cork() is ip6_append_data() and it requires an extra
dst_hold().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
udpv6_sendmsg() first initialises an on-stack 88B struct flowi6 and then
copies it into cork, which is expensive. Avoid the copy in corkless case
by initialising on-stack cork->fl directly.
The main part is a couple of lines under !corkreq check. The rest
converts fl6 variable to be a pointer.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Another preparation patch. inet_cork_full already contains a field for
iflow, so we can avoid passing a separate struct iflow6 into
__ip6_append_data() and ip6_make_skb(), and use the flow stored in
inet_cork_full. Make sure callers set cork->fl, i.e. we init it in
ip6_append_data() and before calling ip6_make_skb().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert a struct inet_cork argument in __ip6_append_data() to struct
inet_cork_full. As one struct contains another inet_cork is still can
be accessed via ->base field. It's a preparation patch making further
changes a bit cleaner.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It doesn't appear there is any reason for ip6_cork_release() to zero
cork->fl, it'll be fully filled on next initialisation. This 88 bytes
memset accounts to 0.3-0.5% of total CPU cycles.
It's also needed in following patches and allows to remove an extar flow
copy in udp_v6_push_pending_frames().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clean up ip6_setup_cork() and ip6_cork_release() adding a local variable
for v6_cork->opt. It's a preparation patch for further changes.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ipv6_push_nfrag_opts() doesn't change passed daddr, and so
__ip6_make_skb() doesn't actually need to keep an on-stack copy of
fl6->daddr. Set initially final_dst to fl6->daddr,
ipv6_push_nfrag_opts() will override it if needed, and get rid of extra
copies.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Corked AF_INET for ipv6 socket doesn't appear to be the hottest case,
so move it out of the common path under up->pending check to remove
overhead.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__ip6_make_skb() gets a cork->dst ref, hands it over to skb and shortly
after puts cork->dst. Save two atomics by stealing it without extra
referencing, ip6_cork_release() handles NULL cork->dst.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Remove leftovers from flowtable modules, from Geert Uytterhoeven.
2) Missing refcount increment of conntrack template in nft_ct,
from Florian Westphal.
3) Reduce nft_zone selftest time, also from Florian.
4) Add selftest to cover stateless NAT on fragments, from Florian Westphal.
5) Do not set net_device when for reject packets from the bridge path,
from Phil Sutter.
6) Cancel register tracking info on nft_byteorder operations.
7) Extend nft_concat_range selftest to cover set reload with no elements,
from Florian Westphal.
8) Remove useless update of pointer in chain blob builder, reported
by kbuild test robot.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: nf_tables: remove assignment with no effect in chain blob builder
selftests: nft_concat_range: add test for reload with no element add/del
netfilter: nft_byteorder: track register operations
netfilter: nft_reject_bridge: Fix for missing reply from prerouting
selftests: netfilter: check stateless nat udp checksum fixup
selftests: netfilter: reduce zone stress test running time
netfilter: nft_ct: fix use after free when attaching zone template
netfilter: Remove flowtable relics
====================
Link: https://lore.kernel.org/r/20220127235235.656931-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Increment the mgmt revision due to recent changes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BPF verifier supports direct memory access for BPF_PROG_TYPE_TRACING type
of bpf programs, e.g., a->b. If "a" is a pointer
pointing to kernel memory, bpf verifier will allow user to write
code in C like a->b and the verifier will translate it to a kernel
load properly. If "a" is a pointer to user memory, it is expected
that bpf developer should be bpf_probe_read_user() helper to
get the value a->b. Without utilizing BTF __user tagging information,
current verifier will assume that a->b is a kernel memory access
and this may generate incorrect result.
Now BTF contains __user information, it can check whether the
pointer points to a user memory or not. If it is, the verifier
can reject the program and force users to use bpf_probe_read_user()
helper explicitly.
In the future, we can easily extend btf_add_space for other
address space tagging, for example, rcu/percpu etc.
Signed-off-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/r/20220127154606.654961-1-yhs@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Current release - new code bugs:
- tcp: add a missing sk_defer_free_flush() in tcp_splice_read()
- tcp: add a stub for sk_defer_free_flush(), fix CONFIG_INET=n
- nf_tables: set last expression in register tracking area
- nft_connlimit: fix memleak if nf_ct_netns_get() fails
- mptcp: fix removing ids bitmap setting
- bonding: use rcu_dereference_rtnl when getting active slave
- fix three cases of sleep in atomic context in drivers: lan966x, gve
- handful of build fixes for esoteric drivers after netdev->dev_addr
was made const
Previous releases - regressions:
- revert "ipv6: Honor all IPv6 PIO Valid Lifetime values", it broke
Linux compatibility with USGv6 tests
- procfs: show net device bound packet types
- ipv4: fix ip option filtering for locally generated fragments
- phy: broadcom: hook up soft_reset for BCM54616S
Previous releases - always broken:
- ipv4: raw: lock the socket in raw_bind()
- ipv4: decrease the use of shared IPID generator to decrease the
chance of attackers guessing the values
- procfs: fix cross-netns information leakage in /proc/net/ptype
- ethtool: fix link extended state for big endian
- bridge: vlan: fix single net device option dumping
- ping: fix the sk_bound_dev_if match in ping_lookup
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=mwR3
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter and can.
Current release - new code bugs:
- tcp: add a missing sk_defer_free_flush() in tcp_splice_read()
- tcp: add a stub for sk_defer_free_flush(), fix CONFIG_INET=n
- nf_tables: set last expression in register tracking area
- nft_connlimit: fix memleak if nf_ct_netns_get() fails
- mptcp: fix removing ids bitmap setting
- bonding: use rcu_dereference_rtnl when getting active slave
- fix three cases of sleep in atomic context in drivers: lan966x, gve
- handful of build fixes for esoteric drivers after netdev->dev_addr
was made const
Previous releases - regressions:
- revert "ipv6: Honor all IPv6 PIO Valid Lifetime values", it broke
Linux compatibility with USGv6 tests
- procfs: show net device bound packet types
- ipv4: fix ip option filtering for locally generated fragments
- phy: broadcom: hook up soft_reset for BCM54616S
Previous releases - always broken:
- ipv4: raw: lock the socket in raw_bind()
- ipv4: decrease the use of shared IPID generator to decrease the
chance of attackers guessing the values
- procfs: fix cross-netns information leakage in /proc/net/ptype
- ethtool: fix link extended state for big endian
- bridge: vlan: fix single net device option dumping
- ping: fix the sk_bound_dev_if match in ping_lookup"
* tag 'net-5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (86 commits)
net: bridge: vlan: fix memory leak in __allowed_ingress
net: socket: rename SKB_DROP_REASON_SOCKET_FILTER
ipv4: remove sparse error in ip_neigh_gw4()
ipv4: avoid using shared IP generator for connected sockets
ipv4: tcp: send zero IPID in SYNACK messages
ipv4: raw: lock the socket in raw_bind()
MAINTAINERS: add missing IPv4/IPv6 header paths
MAINTAINERS: add more files to eth PHY
net: stmmac: dwmac-sun8i: use return val of readl_poll_timeout()
net: bridge: vlan: fix single net device option dumping
net: stmmac: skip only stmmac_ptp_register when resume from suspend
net: stmmac: configure PTP clock source prior to PTP initialization
Revert "ipv6: Honor all IPv6 PIO Valid Lifetime values"
connector/cn_proc: Use task_is_in_init_pid_ns()
pid: Introduce helper task_is_in_init_pid_ns()
gve: Fix GFP flags when allocing pages
net: lan966x: Fix sleep in atomic context when updating MAC table
net: lan966x: Fix sleep in atomic context when injecting frames
ethernet: seeq/ether3: don't write directly to netdev->dev_addr
ethernet: 8390/etherh: don't write directly to netdev->dev_addr
...
When using per-vlan state, if vlan snooping and stats are disabled,
untagged or priority-tagged ingress frame will go to check pvid state.
If the port state is forwarding and the pvid state is not
learning/forwarding, untagged or priority-tagged frame will be dropped
but skb memory is not freed.
Should free skb when __allowed_ingress returns false.
Fixes: a580c76d53 ("net: bridge: vlan: add per-vlan state")
Signed-off-by: Tim Yi <tim.yi@pica8.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20220127074953.12632-1-tim.yi@pica8.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
cppcheck possible warnings:
>> net/netfilter/nf_tables_api.c:2014:2: warning: Assignment of function parameter has no effect outside the function. Did you forget dereferencing it? [uselessAssignmentPtrArg]
ptr += offsetof(struct nft_rule_dp, data);
^
Reported-by: kernel test robot <yujie.liu@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Rename SKB_DROP_REASON_SOCKET_FILTER, which is used
as the reason of skb drop out of socket filter before
it's part of a released kernel. It will be used for
more protocols than just TCP in future series.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/all/20220127091308.91401-2-imagedong@tencent.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
hci_cmd_sync_queue shall return an error if HCI_UNREGISTER flag has
been set as that means hci_unregister_dev has been called so it will
likely cause a uaf after the timeout as the hdev will be freed.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In commit 431280eebe ("ipv4: tcp: send zero IPID for RST and
ACK sent in SYN-RECV and TIME-WAIT state") we took care of some
ctl packets sent by TCP.
It turns out we need to use a similar strategy for SYNACK packets.
By default, they carry IP_DF and IPID==0, but there are ways
to ask them to use the hashed IP ident generator and thus
be used to build off-path attacks.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
One of this way is to force (before listener is started)
echo 1 >/proc/sys/net/ipv4/ip_no_pmtu_disc
Another way is using forged ICMP ICMP_FRAG_NEEDED
with a very small MTU (like 68) to force a false return from
ip_dont_fragment()
In this patch, ip_build_and_send_pkt() uses the following
heuristics.
1) Most SYNACK packets are smaller than IPV4_MIN_MTU and therefore
can use IP_DF regardless of the listener or route pmtu setting.
2) In case the SYNACK packet is bigger than IPV4_MIN_MTU,
we use prandom_u32() generator instead of the IPv4 hashed ident one.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ray Che <xijiache@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Cc: Geoff Alexander <alexandg@cs.unm.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move desc_array from the driver to the pool. The reason behind this is
that we can then reuse this array as a temporary storage for descriptors
in all zero-copy drivers that use the batched interface. This will make
it easier to add batching to more drivers.
i40e is the only driver that has a batched Tx zero-copy
implementation, so no need to touch any other driver.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20220125160446.78976-6-maciej.fijalkowski@intel.com
IIUC the TIPC msg helpers are not meant to provide
and exhaustive API, so remove the unused ones.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping vlan options for a single net device we send the same
entries infinitely because user-space expects a 0 return at the end but
we keep returning skb->len and restarting the dump on retry. Fix it by
returning the value from br_vlan_dump_dev() if it completed or there was
an error. The only case that must return skb->len is when the dump was
incomplete and needs to continue (-EMSGSIZE).
Reported-by: Benjamin Poirier <bpoirier@nvidia.com>
Fixes: 8dcea18708 ("net: bridge: vlan: add rtm definitions and dump support")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b75326c201.
This commit breaks Linux compatibility with USGv6 tests. The RFC this
commit was based on is actually an expired draft: no published RFC
currently allows the new behaviour it introduced.
Without full IETF endorsement, the flash renumbering scenario this
patch was supposed to enable is never going to work, as other IPv6
equipements on the same LAN will keep the 2 hours limit.
Fixes: b75326c201 ("ipv6: Honor all IPv6 PIO Valid Lifetime values")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different netns has different requirement on the setting of min_adv_mss
sysctl which the advertised MSS will be never lower than.
Enable min_adv_mss to be configured per network namespace.
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning -1 does not indicate anything useful.
Use a standard and meaningful error code instead.
Fixes: a26c5fd762 ("nl802154: add support for security layer")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-6-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
This reverts commit b515d26372.
Commit b515d26372 ("xfrm: xfrm_state_mtu
should return at least 1280 for ipv6") in v5.14 breaks the TCP MSS
calculation in ipsec transport mode, resulting complete stalls of TCP
connections. This happens when the (P)MTU is 1280 or slighly larger.
The desired formula for the MSS is:
MSS = (MTU - ESP_overhead) - IP header - TCP header
However, the above commit clamps the (MTU - ESP_overhead) to a
minimum of 1280, turning the formula into
MSS = max(MTU - ESP overhead, 1280) - IP header - TCP header
With the (P)MTU near 1280, the calculated MSS is too large and the
resulting TCP packets never make it to the destination because they
are over the actual PMTU.
The above commit also causes suboptimal double fragmentation in
xfrm tunnel mode, as described in
https://lore.kernel.org/netdev/20210429202529.codhwpc7w6kbudug@dwarf.suse.cz/
The original problem the above commit was trying to fix is now fixed
by commit 6596a02295 ("xfrm: fix MTU
regression").
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Remove two dead stubs, sk_msg_clear_meta() was never
used, use of xskq_cons_is_full() got replaced by
xsk_tx_writeable() in v5.10.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220126185412.2776254-1-kuba@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cancel tracking for byteorder operation, otherwise selector + byteorder
operation is incorrectly reduced if source and destination registers are
the same.
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Prior to commit fa538f7cf0 ("netfilter: nf_reject: add reject skbuff
creation helpers"), nft_reject_bridge did not assign to nskb->dev before
passing nskb on to br_forward(). The shared skbuff creation helpers
introduced in above commit do which seems to confuse br_forward() as
reject statements in prerouting hook won't emit a packet anymore.
Fix this by simply passing NULL instead of 'dev' to the helpers - they
use the pointer for just that assignment, nothing else.
Fixes: fa538f7cf0 ("netfilter: nf_reject: add reject skbuff creation helpers")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The conversion erroneously removed the refcount increment.
In case we can use the percpu template, we need to increment
the refcount, else it will be released when the skb gets freed.
In case the slowpath is taken, the new template already has a
refcount of 1.
Fixes: 7197743776 ("netfilter: conntrack: convert to refcount_t api")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
NF_FLOW_TABLE_IPV4 and NF_FLOW_TABLE_IPV6 are invisble, selected by
nothing (so they can no longer be enabled), and their last real users
have been removed (nf_flow_table_ipv6.c is empty).
Clean up the leftovers.
Fixes: c42ba4290b ("netfilter: flowtable: remove ipv4/ipv6 modules")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
xfrm_migrate cannot handle address family change of an xfrm_state.
The symptons are the xfrm_state will be migrated to a wrong address,
and sending as well as receiving packets wil be broken.
This commit fixes it by breaking the original xfrm_state_clone
method into two steps so as to update the props.family before
running xfrm_init_state. As the result, xfrm_state's inner mode,
outer mode, type and IP header length in xfrm_state_migrate can
be updated with the new address family.
Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/1885354
Signed-off-by: Yan Yan <evitayan@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch enables distinguishing SAs and SPs based on if_id during
the xfrm_migrate flow. This ensures support for xfrm interfaces
throughout the SA/SP lifecycle.
When there are multiple existing SPs with the same direction,
the same xfrm_selector and different endpoint addresses,
xfrm_migrate might fail with ENODATA.
Specifically, the code path for performing xfrm_migrate is:
Stage 1: find policy to migrate with
xfrm_migrate_policy_find(sel, dir, type, net)
Stage 2: find and update state(s) with
xfrm_migrate_state_find(mp, net)
Stage 3: update endpoint address(es) of template(s) with
xfrm_policy_migrate(pol, m, num_migrate)
Currently "Stage 1" always returns the first xfrm_policy that
matches, and "Stage 3" looks for the xfrm_tmpl that matches the
old endpoint address. Thus if there are multiple xfrm_policy
with same selector, direction, type and net, "Stage 1" might
rertun a wrong xfrm_policy and "Stage 3" will fail with ENODATA
because it cannot find a xfrm_tmpl with the matching endpoint
address.
The fix is to allow userspace to pass an if_id and add if_id
to the matching rule in Stage 1 and Stage 2 since if_id is a
unique ID for xfrm_policy and xfrm_state. For compatibility,
if_id will only be checked if the attribute is set.
Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/1668886
Signed-off-by: Yan Yan <evitayan@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The current implementation of HTB offload doesn't support some
parameters. Instead of ignoring them, actively return the EINVAL error
when they are set to non-defaults.
As this patch goes to stable, the driver API is not changed here. If
future drivers support more offload parameters, the checks can be moved
to the driver side.
Note that the buffer and cbuffer parameters are also not supported, but
the tc userspace tool assigns some default values derived from rate and
ceil, and identifying these defaults in sch_htb would be unreliable, so
they are still ignored.
Fixes: d03b195b5a ("sch_htb: Hierarchical QoS hardware offload")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220125100654.424570-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sk_gso_max_size is set based on the dst dev. Both users of it
adjust the value by the same offset - (MAX_TCP_HEADER + 1). Rather
than compute the same adjusted value on each call do the adjustment
once when set.
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220125024511.27480-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
HCI_EV_VENDOR is in fact variable length since it acts as metaevent
where a vendor can implement their own event sets.
In addition to it this makes use of bt_dev_warn_ratelimited to supress
the amount of logging in case the event has more data than expected.
Fixes: 3e54c5890c ("Bluetooth: hci_event: Use of a function table to handle HCI event")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The invalid SCO handle error is normally caused by a race in the USB
transport where the data and event happen to be 2 different endpoints
so the event carrying the SCO handle is processed after its data.
Note: This can probably be resolved with use of force_poll_sync
debugfs.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
- New Features:
- Basic handling for case insensitive filesystems
- Initial support for fs_locations and server trunking
- Bugfixes and Cleanups:
- Cleanups to how the "struct cred *" is handled for the nfs_access_entry
- Ensure the server has an up to date ctimes before hardlinking or renaming
- Update 'blocks used' after writeback, fallocate, and clone
- nfs_atomic_open() fixes
- Improvements to sunrpc tracing
- Various null check & indenting related cleanups
- Some improvements to the sunrpc sysfs code
- Use default_groups in kobj_type
- Fix some potential races and reference leaks
- A few tracepoint cleanups in xprtrdma
-----BEGIN PGP SIGNATURE-----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=wcVT
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.17-1' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client updates from Anna Schumaker:
"New Features:
- Basic handling for case insensitive filesystems
- Initial support for fs_locations and server trunking
Bugfixes and Cleanups:
- Cleanups to how the "struct cred *" is handled for the
nfs_access_entry
- Ensure the server has an up to date ctimes before hardlinking or
renaming
- Update 'blocks used' after writeback, fallocate, and clone
- nfs_atomic_open() fixes
- Improvements to sunrpc tracing
- Various null check & indenting related cleanups
- Some improvements to the sunrpc sysfs code:
- Use default_groups in kobj_type
- Fix some potential races and reference leaks
- A few tracepoint cleanups in xprtrdma"
[ This should have gone in during the merge window, but didn't. The
original pull request - sent during the merge window - had gotten
marked as spam and discarded due missing DKIM headers in the email
from Anna. - Linus ]
* tag 'nfs-for-5.17-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (35 commits)
SUNRPC: Don't dereference xprt->snd_task if it's a cookie
xprtrdma: Remove definitions of RPCDBG_FACILITY
xprtrdma: Remove final dprintk call sites from xprtrdma
sunrpc: Fix potential race conditions in rpc_sysfs_xprt_state_change()
net/sunrpc: fix reference count leaks in rpc_sysfs_xprt_state_change
NFSv4.1 test and add 4.1 trunking transport
SUNRPC allow for unspecified transport time in rpc_clnt_add_xprt
NFSv4 handle port presence in fs_location server string
NFSv4 expose nfs_parse_server_name function
NFSv4.1 query for fs_location attr on a new file system
NFSv4 store server support for fs_location attribute
NFSv4 remove zero number of fs_locations entries error check
NFSv4: nfs_atomic_open() can race when looking up a non-regular file
NFSv4: Handle case where the lookup of a directory fails
NFSv42: Fallocate and clone should also request 'blocks used'
NFSv4: Allow writebacks to request 'blocks used'
SUNRPC: use default_groups in kobj_type
NFS: use default_groups in kobj_type
NFS: Fix the verifier for case sensitive filesystem in nfs_atomic_open()
NFS: Add a helper to remove case-insensitive aliases
...
IPv6 GRO considers packets to belong to different flows when their
hop_limit is different. This seems counter-intuitive, the flow is
the same. hop_limit may vary because of various bugs or hacks but
that doesn't mean it's okay for GRO to reorder packets.
Practical impact of this problem on overall TCP performance
is unclear, but TCP itself detects this reordering and bumps
TCPSACKReorder resulting in user complaints.
Eric warns that there may be performance regressions in setups
which do packet spraying across links with similar RTT but different
hop count. To be safe let's target -next and not treat this
as a fix. If the packet spraying is using flow label there should
be no difference in behavior as flow label is checked first.
Note that the code plays an easy to miss trick by upcasting next_hdr
to a u16 pointer and compares next_hdr and hop_limit in one go.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
