Adds linux/dvb/frontend.h header file at DocBook, and creates cross-references
for the frontend ioctls.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename all sessions id's for frontend ioctls to match ioctl name and
add the proper cross-link references for those ioctls.
This also helps to identify what ioctls are missing specs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default streaming control timeout was found by Ondrej Zary to be too low
for some Logitech webcams. With kernel 2.6.22 and newer they would timeout
during initialization unles the audio function was initialized before the
video function.
Add a module parameter to set the streaming control timeout and increase the
default value from 1000ms to 3000ms to fix the above problem.
Thanks to Ondrej Zary for investigating the issue and providing an initial
patch.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At least one 5986:0241 webcam model includes vendor-specific descriptors
at the end of its streaming interface descriptors. Print an information
UVC_TRACE_DESCR message and try to continue parsing the descriptors
rather than bailing out with an error.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch sets stream->urb_size as psize*npackets
before calling uvc_alloc_urb_buffers, which may fix
a possible failure of usb_buffer_free in case usb_buffer_alloc
returns NULL. The patch is based on the ideas below:
1,If usb_buffer_alloc can't allocate a buffer sucessfully,
uvc_free_urb_buffers will be called to free the allocated
buffers, and stream->urb_size is required to be passed to
usb_buffer_free;
2,uvc_free_urb_buffers can reset stream->urb_size.
This patch is against linux-v2.6.31-next-20090926.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The uvcvideo driver has a driver-wide lock and a reference count to protect
against a disconnect/open race. Now that videodev handles the race itself,
reference-counting in the driver can be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dismiss privileges on the file handle when calling VIDIOC_REQBUFS with a
buffer count of 0. This allows applications to release the streaming
permissions on the file handle without closing it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VIDIOC_TRY_FMT ioctl doesn't interfere with video streaming and thus
should succeed on an unprivileged file handle.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the trace level for messages related to video URB buffers allocation and
alternate setting selection.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return minimum, maximum and step set to 0 without querying the hardware.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There were various "if (sensor == foo)" pieces of code inside ov519.c,
move these bits to the sensor specific init functions, where they
belong.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gscpa_ov519: add support for the ovfx2 bridge
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the OV2610 and OV3610 sensors to the gspca
ov519 subdriver. This is a preparation patch for adding ovfx2 bridge
support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CIF sensor type 1 exposure setting got clamped at 300, as settings below
300 do not work well (and do work for the other sensors). This patch
scales the 0-4095 range to 300-4095 instead of ignoring changes between
300, avoiding have a part of the control range where nothing happens.
This is esp. important for software autogain as done by libv4l.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While checking all gspca sub drivers pkt_scan functions for a bug I found in
1 of them (and after checking also in another), I noticed a bug in the
gspca_sq905c work queue function, once it has decided to start discarding a
frame because the application is not reading fast enough (and thus returning
buffers to fill fast enough), it never stops discarding.
This patch fixes this by simply completely removing the "discarding"
variable, if we need to discard the current frame because there is no buffer
to store it, the "frame" pointer will be NULL, so that is all we need to
check.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While checking all gspca sub drivers pkt_scan functions for a bug I found in
1 of them (and after checking also in another), I noticed a bug in the
gspca_jeilinj work queue function, once it has decided to start discard a
frame because the application is not reading fast enough (and thus returning
buffers to fill fast enough), it never stops discarding.
This patch fixes this by simply completely removing the "discarding"
variable, if we need to discard the current frame because there is no buffer
to store it, the "frame" pointer will be NULL, so that is all we need to
check.
I've also moved the gspca_get_i_frame() call and the writing of the jpg
header to the buffer to after the first usb_bulk_msg() call, as we don't
need it before that, and that will give the app slightly more time to
queue a buffer for us to fill.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improve (and also simplify :) gspca_mr97310a: VGA sensor type detection.
As it was still failing on some machines (not with some cams, but on
some machines interesting enough).
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-Remove use of unneeded discarding variable
-Cleanup locking to only take usb_lock around access to the control
endpoint, by no longer taking the lock around the bulk transfer
(which takes most of the time) we can remove the msleep(1) which was
needed to give the gspca core a chance to grab the usb_lock to signal
us to stop.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds controls for vga cams with sensor type 0, in order to
correctly report the present controls, the probing of the sensor type
has been moved from sd_start to sd_config, since this made the sensor
type probing unreliable the detection method was changed.
Note this requires the camera to enter streaming mode, so sd_config now
briefly makes the camera stream.
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as TeVii S460,S420.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as:
TeVii S460,S420; Omicom SS4; SatTrade ST4200;
TBS 8920,8910; Prof 7300,6200.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds an soc-camera / v4l2-subdev driver for the RJ54N1CB0C CMOS camera
sensor from Sharp. The sensor is very picky about initialisation and
configuration sequences. The driver limits artificially maximum window size by
800x600, although the sensor supports 1600x1200. Sizes above 800x600 don't seem
to work correctly, besides, examples from the system integrator use sizes above
640x480 only for still photography. Unfortunately, I had to use "magic"
register-value pairs for undocumented and "reserved" registers. This version of
the driver also omits some functionality, like cropping, which hasn't been
sufficiently tested yet and will be added later.
create mode 100644 drivers/media/video/rj54n1cb0c.c
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If CEU driver can not receive data from camera,
CETCR has VBP error state.
Then, CEU is stopped and cure operation is needed.
This patch add VBP error cure operation.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add comment about the meaning of the fixed JPEG header bytes used to
create each image.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The length check in reg_w_var() function is because the buffer contents
is copied to gspca_dev->usb_buf which has the size of USB_BUF_SZ bytes as
defined in drivers/media/video/gspca/gspca.h. Replace the number with
symbol for better readability and maintainability.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert tda18271_rf_tracking_filter_cal.rf_[ab][12] from int to s32.
Convert tda18271_priv.tm_rfcal from unsigned int to u8.
Cast subtractions between u32 values as s32.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use temporary variables for signed calulations between unsigned values
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds a forgotten module_param macro needed to set a deemphasis of 50us.
It is the standard setting for commercial FM radio broadcasts outside the US.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
override set_frontend to allow rf input path switching on the HVR1275
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes adds IR Rx keypress input event handling to the CX23885 module.
This change specifically only adds input handling for IR devices implemented as
v4l2_subdevices, using only the pulse width mode (for now), and only with
RC-5 remotes. The V4L-DVB infrastructure is missing too much to support RC-6
mode 6A as used in many media center remotes. The grey Hauppauge RC-5 remote
and HVR-1850 IR receiver work now.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add integrated IR subdevice interrupt and notification handling. This is in
preparation of input keypress handling changes for the cx23885 module.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change completes the v4l2_subdev implementation for IR receive for the
IR controller built into the CX23888.
This changes almost completes the IR transmit side also, but doesn't. Instead
notes in the comments describe what needs to be done for IR Tx to work in the
subdevice implementation.
The current Tx behavior is skeletal and benign. If left alone, it does nothing.
It will only ever generate a Tx interrupt on Tx init by a caller or when the
tx_write() method is called. The ISR, when called, will then disable the Tx
FIFO service interrupt.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add v4l2_subdev_ir_ops and IR notify defines for v4l2_device. This change
is specifically needed at this time to support the integrated IR controller in
the CX2388[58] chips.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The prior mechanism wasn't reliable with the cx23887. This new mechanism
tests correctly against cx23885, 7 and 8 based products.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the IR controller on the CX23888 to work for the HVR-1850 and in
general, the A/V core must be initialized to get the VID_CLK going.
The VID_CLK is the timing reference for the CX23888's integrated
IR controller.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The SYS and AUX PLLs need to be initialized to different values based on
the chip: CX23885, CX23887, CX23888, as each uses a different crystal
frequency: 28.6363 MHz, 25.0 MHz, 50.0 MHz.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
