- relbranch_fixup(), for non-branches, would end up setting
regs->tnpc incorrectly, in fact it would set it equal to
regs->tpc which would cause that instruction to execute twice
Also, if this is not a PC-relative branch, we should just
leave regs->tnpc as-is. This covers cases like 'jmpl' which
branch to absolute values.
- To be absolutely %100 safe, we need to flush the instruction
cache for all assignments to kprobe->ainsn.insn[], including
cases like add_aggr_kprobe()
- prev_kprobe's status field needs to be 'unsigned long' to match
the type of the value it is saving
- jprobes were totally broken:
= jprobe_return() can run in the stack frame of the jprobe handler,
or in an even deeper stack frame, thus we'll be in the wrong
register window than the one from the original probe state.
So unwind using 'restore' instructions, if necessary, right
before we do the jprobe_return() breakpoint trap.
= There is no reason to save/restore the register window saved
at %sp at jprobe trigger time. Those registers cannot be
modified by the jprobe handler. Also, this code was saving
and restoring "sizeof (struct sparc_stackf)" bytes. Depending
upon the caller, this could clobber unrelated stack frame
pieces if there is only a basic 128-byte register window
stored on the stack, without the argument save area.
So just saving and restoring struct pt_regs is sufficient.
= Kill the "jprobe_saved_esp", totally unused.
Also, delete "jprobe_saved_regs_location", with the stack frame
unwind now done explicitly by jprobe_return(), this check is
superfluous.
Signed-off-by: David S. Miller <davem@davemloft.net>
ptrace_traceme() consolidation made
ret = ptrace_traceme();
dead write.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userspace is forbidden from making unaligned loads and
stores. So if we get an unaligned trap due to a
{get,put}_user(), signal a fault and run the exception
handler.
Signed-off-by: David S. Miller <davem@davemloft.net>
To add this logic, put the VIS instruction check at the
vis_emul() call site instead of inside of vis_emul().
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Voyager and Visual WS already define ARCH_SETUP,
it looks like PARAVIRT shouldn't be offered for them.
In file included from arch/i386/kernel/setup.c:63:
include/asm-i386/mach-visws/setup_arch.h:8:1: warning: "ARCH_SETUP" redefin=
ed
In file included from include/asm/msr.h:5,
from include/asm/processor.h:17,
from include/asm/thread_info.h:16,
from include/linux/thread_info.h:21,
from include/linux/preempt.h:9,
from include/linux/spinlock.h:49,
from include/linux/capability.h:45,
from include/linux/sched.h:46,
from arch/i386/kernel/setup.c:26:
include/asm/paravirt.h:163:1: warning: this is the location of the previous=
definition
In file included from arch/i386/kernel/setup.c:63:
include/asm-i386/mach-visws/setup_arch.h:8:1: warning: "ARCH_SETUP" redefin=
ed
In file included from include/asm/msr.h:5,
from include/asm/processor.h:17,
from include/asm/thread_info.h:16,
from include/linux/thread_info.h:21,
from include/linux/preempt.h:9,
from include/linux/spinlock.h:49,
from include/linux/capability.h:45,
from include/linux/sched.h:46,
from arch/i386/kernel/setup.c:26:
include/asm/paravirt.h:163:1: warning: this is the location of the previous=
definition
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
gcc 4.2 warns
linux/arch/i386/kernel/io_apic.c: In function ‘create_irq’:
linux/arch/i386/kernel/io_apic.c:2488: warning: ‘vector’ may be used uninitialized in this function
The warning is false, but somewhat legitimate so work around it.
Signed-off-by: Andi Kleen <ak@suse.de>
oprofile uses smp_num_siblings without testing for CONFIG_X86_HT.
I looked at modifying oprofile, but this way is cleaner & simpler
and I didn't see a good reason not to just export it when CONFIG_SMP.
WARNING: "smp_num_siblings" [arch/i386/oprofile/oprofile.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The new PDA code uses a dummy _proxy_pda variable to describe
memory references to the PDA. It is never referenced
in inline assembly, but exists as input/output arguments.
gcc 4.2 in some cases can CSE references to this which causes
unresolved symbols. Define it to zero to avoid this.
Signed-off-by: Andi Kleen <ak@suse.de>
2.6.19 stopped booting (or booted based on build/config) on our x86_64
systems due to a bug introduced in 2.6.19. check_nmi_watchdog schedules an
IPI on all cpus to busy wait on a flag, but fails to set the busywait
flag if NMI functionality is disabled. This causes the secondary cpus
to spin in an endless loop, causing the kernel bootup to hang.
Depending upon the build, the busywait flag got overwritten (stack variable)
and caused the kernel to bootup on certain builds. Following patch fixes
the bug by setting the busywait flag before returning from check_nmi_watchdog.
I guess using a stack variable is not good here as the calling function could
potentially return while the busy wait loop is still spinning on the flag.
AK: I redid the patch significantly to be cleaner
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix verify_quirk_intel_irqbalance(). genapic checks should really
happen only on affected versions of the E7520/E7320/E7525 based platforms.
AK: This should akpm's Coyote SDV
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Remove bogus comments about unexporting cache_{push,clear}(), as inline
dma_cache_maintenance() (used by at least bionet and pamsnet) calls them.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Atari IDE: The interrupt needs SA_SHIRQ now to get registered.
Signed-off-by: Michael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
General compile fixes for 2.6.16 for sun3, and some updates to make the new
bootloader work correctly. Tested on 3/50, 3/60, 3/80.
Signed-off-by: Sam Creasey <sammy@sammy.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that i8259A_chip uses new irq flow handler select
GENERIC_HARDIRQS_NO__DO_IRQ on some more platforms.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Delete dead codes at end of the function and move small_csumcopy
there. This makes some labels (maybe_end_cruft, small_memcpy,
end_bytes, out) needless and eliminates some branches.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use standard o32 register name instead of T0, T1, etc, like memcpy.S.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Poison init section before freeing it.
[S390] Use add_active_range() and free_area_init_nodes().
[S390] Virtual memmap for s390.
[S390] Update documentation for dynamic subchannel mapping.
[S390] Use dev->groups for adding/removing the subchannel attribute group.
[S390] Support for disconnected devices reappearing on another subchannel.
[S390] subchannel lock conversion.
[S390] Some preparations for the dynamic subchannel mapping patch.
[S390] runtime switch for qdio performance statistics
[S390] New DASD feature for ERP related logging
[S390] add reset call handler to the ap bus.
[S390] more workqueue fixes.
[S390] workqueue fixes.
[S390] uaccess_pt: add missing down_read() and convert to is_init().
In VMSPLIT mode, kernel PGD might have more entries than user space.
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert SH to use generic ioremap_page_range()
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace occurences of task->signal->session by a new process_session() helper
routine.
It will be useful for pid namespaces to abstract the session pid number.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide ilog2() fallbacks for powerpc for 32-bit numbers and 64-bit numbers on
ppc64.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
