Tegra I2C device isn't guaranteed to be suspended after removal of
the driver since driver uses pm_runtime_put() that is asynchronous and
pm_runtime_disable() cancels pending power-change requests. This means
that potentially refcount of the clocks may become unbalanced after
removal of the driver. This a very minor problem which unlikely to
happen in practice and won't cause any visible problems, nevertheless
let's replace pm_runtime_disable() with pm_runtime_force_suspend() and
use pm_runtime_put_sync() which disables RPM of the device and puts it
into suspend before driver is removed.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit a6b8bb6a81 ("i2c: i801: Fix handling SMBHSTCNT_PEC_EN")
attempts to disable software PEC by clearing the SMBHSTCNT_PEC_EN (bit 7)
in the SMBus Host Control register (I/O SMBHSTCNT) but incorrectly
clears it in the PCI Host Configuration register (PCI SMBHSTCFG).
This clearing is actually needless since after above commit the
SMBHSTCNT_PEC_EN is never set and the register is initialized with known
values.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When a timeout error occurs in i2c transter, it is usually related
to the i2c/dma IP hardware configuration. Therefore, the purpose of
this patch is to dump the key register values of i2c/dma when a
timeout occurs in i2c for debugging.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Due to changes in the hardware design of the handshaking signal
between i2c and dma, it is necessary to reset the handshaking
signal before each transfer to ensure that the multi-msgs can
be transferred correctly.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Allow polling time setting according to I2C frequency supported across
the system. For base frequency 400 KHz and 1 MHz set polling time is set
four times less than for system with base frequency 100KHz.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some later revisions after the original PASemi I2C controller introduce
what likely is an enable bit to the CTL register. Without setting it the
actual i2c transmission is never started.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With all the previous preparations we can now finally add
the platform driver to support the PASemi-based controllers
in Apple SoCs. This does not work on the M1 yet but should
work on the early iPhones already.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using managed device resources means there's nothing left to be done in
pasemi_smb_pci_remove and also allows to remove base and size from
struct pasemi_smbus.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Right now the bus frequency has always been hardcoded as
100 KHz with the specific reference clock used in the PASemi
PCI controllers. Make this configurable to prepare for the
platform driver.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Split out common reset call to its own function so that we
can later add support for selecting the clock frequency
and an additional enable bit found in newer revisions.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Split off the PCI driver so that we can reuse common code for the
platform driver.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Split off common probing code that will be used by both the PCI and the
platform device.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Prepare to create a platform driver by removing all usages of pci_dev we
can.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Right now the i2c adapter name includes the port number which can
indirectly be used to identify the device. Replace that with dev_name
to directly identify the device and to also allow this to work correctly
once we add platform support.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In preparation for splitting this driver up into a platform_driver
and a pci_driver, replace outl/inl usage with pci_iomap and
ioread32/iowrite32.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Decrease polling time 'MLXCPLD_I2C_POLL_TIME' from 400 usec to 200
usec. It improves performance of I2C transactions.
Reliability of setting polling time to 200 usec has been validated
across all the supported systems.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change setting for 400KHz frequency support by more accurate value.
Fixes: 66b0c2846b ("i2c: mlxcpld: Add support for I2C bus frequency setting")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Value for getting frequency capability wrongly has been taken from
register offset instead of register value.
Fixes: 66b0c2846b ("i2c: mlxcpld: Add support for I2C bus frequency setting")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In the commit be5ce0e97c ("i2c: mediatek: Add i2c ac-timing adjust
support"), we miss setting OFFSET_EXT_CONF register if
i2c->dev_comp->timing_adjust is false, now add it back.
Fixes: be5ce0e97c ("i2c: mediatek: Add i2c ac-timing adjust support")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
acpi_i2c_find_adapter_by_handle() calls bus_find_device() which takes a
reference on the adapter which is never released which will result in a
reference count leak and render the adapter unremovable. Make sure to
put the adapter after creating the client in the same manner that we do
for OF.
Fixes: 525e6fabea ("i2c / ACPI: add support for ACPI reconfigure notifications")
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: fixed title]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The reason for the modification here is that the previous
offset information is incorrect, OFFSET_DEBUGSTAT = 0xE4 is
the correct value.
Fixes: 25708278f8 ("i2c: mediatek: Add i2c support for MediaTek MT8183")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Class based instantiation has already been removed for other controllers
and it makes absolutely sense to do it for this one too.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Acked-by: Ingmar Klein <ingmar.klein@kontron.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: zhaoxiao <long870912@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We want to enable the interrupts _before_ starting the transfer because
it is good programming style and also the proposed order in the R-Car
manual. There is no difference in practice because it doesn't matter in
which order both conditions appear if we wait for both to happen.
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The original change works as intended, but Andy pointed in [0] that now
userspace could re-enable RPM via sysfs, even though we explicitly want
to disable it. So effectively revert the original patch, just with small
improvements:
- Calls to pm_runtime_allow()/pm_runtime_forbid() don't have to be
balanced, so we can remove the call to pm_runtime_forbid() in
i801_remove().
- priv->acpi_reserved is accessed after i801_acpi_remove(), and according
to Robert [1] the custom handler can't run any longer. Therefore we
don't have to take priv->acpi_lock.
[0] https://www.spinics.net/lists/linux-i2c/msg52730.html
[1] https://lore.kernel.org/linux-acpi/BYAPR11MB32561D19A0FD9AB93E2B1E5287D39@BYAPR11MB3256.namprd11.prod.outlook.com/T/#t
Fixes: 4e60d5dd10 ("i2c: i801: Improve disabling runtime pm")
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
As pointed out by Andy in [0] using a local mutex here isn't strictly
wrong but not sufficient. We should hold the PCI rescan lock for P2SB
operations.
[0] https://www.spinics.net/lists/linux-i2c/msg52717.html
Fixes: 1a987c69ce ("i2c: i801: make p2sb_spinlock a mutex")
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The return value of i801_add_mux() isn't used, so let's change it to void.
In addition remove the not needed cast to struct gpiod_lookup.
GPIO_LOOKUP() uses GPIO_LOOKUP_IDX() that includes this cast.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
By using ACPI_HANDLE() the handler argument can be retrieved directly.
Both address space handler functions check the handler argument and
return an error if it's NULL. This allows to further simplify the code.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
do_pci_enable_device() takes care that PCI_COMMAND_INTX_DISABLE
is cleared if a legacy interrupt is used.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace the ugly cast of the return_value pointer with proper usage.
In addition use dmi_match() instead of open-coding it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In case the XIIC does TX/RX transfer, make sure no other kernel thread
can start another TX transfer at the same time. This could happen since
the driver only checks tx_msg for being non-NULL and returns -EBUSY in
that case, however it is necessary to check also rx_msg for the same.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Transferring multiple messages via XIIC suffers from strange interaction
between the interrupt status/enable register flags. These flags are being
reused in the hardware to indicate different things for read and write
transfer, and doing multiple transactions becomes horribly complex. Just
send a single transaction and reload the controller with another message
once the transaction is done in the interrupt handler thread.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
There will never be threads queueing up in the xiic_xmit(), use
completion synchronization primitive to wait for the interrupt
handler thread to complete instead as it is much better fit and
there is no need to overload it for this purpose.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The __xiic_start_xfer() manipulates the interrupt flags, xiic_wakeup()
may result in return from xiic_xfer() early. Defer both to the end of
the xiic_process() interrupt thread, so that they are executed after
all the other interrupt bits handling completed and once it completely
safe to perform changes to the interrupt bits in the hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The interrupt handler is missing locking when reading out registers
and is racing with other threads which might access the driver. Drop
it altogether, so that the threaded interrupt is always executed, as
that one is already serialized by the driver mutex. This also allows
dropping local_irq_save()/local_irq_restore() in xiic_start_recv().
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The tx_msg is set from multiple places, sometimes without locking,
which fall apart on any SMP system. Only ever access tx_msg inside
the driver mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Highlights:
- Move all the Intel drivers into their own subdir(s) (mostly Kate's work)
- New meraki-mx100 platform driver
- Asus WMI driver enhancements, including
/sys/firmware/acpi/platform_profile support
- New BIOS SAR driver for Intel M.2 WWAM modems
- Alder Lake support for the Intel PMC driver
- A whole bunch of cleanups + fixes all over the place
The following is an automated git shortlog grouped by driver:
BIOS SAR driver for Intel M.2 Modem:
- BIOS SAR driver for Intel M.2 Modem
ISST:
- use semi-colons instead of commas
- Fix optimization with use of numa
Replace deprecated CPU-hotplug functions.:
- Replace deprecated CPU-hotplug functions.
Update Mario Limonciello's email address in the docs:
- Update Mario Limonciello's email address in the docs
acer-wmi:
- Add Turbo Mode support for Acer PH315-53
add meraki-mx100 platform driver:
- add meraki-mx100 platform driver
asus-nb-wmi:
- Add tablet_mode_sw=lid-flip quirk for the TP200s
- Allow configuring SW_TABLET_MODE method with a module option
asus-wmi:
- Fix "unsigned 'retval' is never less than zero" smatch warning
- Delete impossible condition
- Add support for platform_profile
- Add egpu enable method
- Add dgpu disable method
- Add panel overdrive functionality
dell-smbios:
- Remove unused dmi_system_id table
dell-smbios-wmi:
- Add missing kfree in error-exit from run_smbios_call
- Avoid false-positive memcpy() warning
dell-smo8800:
- Convert to be a platform driver
dual_accel_detect:
- Use the new i2c_acpi_client_count() helper
gigabyte-wmi:
- add support for B450M S2H V2
- add support for X570 GAMING X
hp_accel:
- Convert to be a platform driver
- Remove _INI method call
i2c:
- acpi: Add an i2c_acpi_client_count() helper function
i2c-multi-instantiate:
- Use the new i2c_acpi_client_count() helper
ideapad-laptop:
- Fix Legion 5 Fn lock LED
intel-hid:
- Move to intel sub-directory
intel-rst:
- Move to intel sub-directory
intel-smartconnect:
- Move to intel sub-directory
intel-uncore-frequency:
- Move to intel sub-directory
intel-vbtn:
- Move to intel sub-directory
intel-wmi-sbl-fw-update:
- Move to intel sub-directory
intel-wmi-thunderbolt:
- Move to intel sub-directory
intel_atomisp2:
- Move to intel sub-directory
intel_bxtwc_tmu:
- Move to intel sub-directory
intel_cht_int33fe:
- Use the new i2c_acpi_client_count() helper
intel_chtdc_ti_pwrbtn:
- Move to intel sub-directory
intel_int0002_vgpio:
- Move to intel sub-directory
intel_mrfld_pwrbtn:
- Move to intel sub-directory
intel_oaktrail:
- Move to intel sub-directory
intel_pmc_core:
- Move to intel sub-directory
- Prevent possibile overflow
intel_pmt_telemetry:
- Ignore zero sized entries
intel_punit_ipc:
- Move to intel sub-directory
intel_scu_ipc:
- Fix doc of intel_scu_ipc_dev_command_with_size()
intel_speed_select_if:
- Move to intel sub-directory
intel_telemetry:
- Move to intel sub-directory
intel_turbo_max_3:
- Move to intel sub-directory
lg-laptop:
- Use correct event for keyboard backlight FN-key
- Use correct event for touchpad toggle FN-key
- Support for battery charge limit on newer models
platform/mellanox:
- mlxbf-pmc: fix kernel-doc notation
platform/surface:
- aggregator: Use y instead of objs in Makefile
- surface3_power: Use i2c_acpi_get_i2c_resource() helper
platform/x86/intel:
- pmc/core: Add GBE Package C10 fix for Alder Lake PCH
- pmc/core: Add Alder Lake low power mode support for pmc core
- pmc/core: Add Latency Tolerance Reporting (LTR) support to Alder Lake
- pmc/core: Add Alderlake support to pmc core driver
- int3472: Use y instead of objs in Makefile
- pmt: Use y instead of objs in Makefile
- int33fe: Use y instead of objs in Makefile
- Move Intel PMT drivers to new subfolder
thermal/drivers/intel:
- Move intel_menlow to thermal drivers
think-lmi:
- add debug_cmd
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmEw1KAUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9wk7Qf/dsaaDgx7aC6DfKzdcMgfeLIdTaGm
a6svNXM2t/JFdvhjYzxA+4QlQgco7zkN06iRlWbObEonSUsHlGlwEOHX60VgcopO
qJaqnznmfdXUocFTnA+5acJXabNaw7xkKHS0K61UWgk+mm6aMuygpKxULnNTa4X+
p3HoU6uXFckpoA/Jstzo5UfegNYhg11bflNd7XN4F3rMCbbNHAsWlf4oVr2YsEHa
wECW+1e8wZl4BInUzoXQhilRoybJWXWJ8sLsvQfDXLs9aNoLdDqu9p0MuXEW5QqE
wNt26SNNAP2L49BD6kaJszV5Ry/jNSEtVkWwkrzHbGTZoOEyMYas8pm6Uw==
=iK1W
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
- Move all the Intel drivers into their own subdir(s) (mostly Kate's
work)
- New meraki-mx100 platform driver
- Asus WMI driver enhancements, including support for
/sys/firmware/acpi/platform_profile
- New BIOS SAR driver for Intel M.2 WWAM modems
- Alder Lake support for the Intel PMC driver
- A whole bunch of cleanups + fixes all over the place"
* tag 'platform-drivers-x86-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (65 commits)
platform/x86: dell-smbios-wmi: Add missing kfree in error-exit from run_smbios_call
platform/x86: dell-smbios-wmi: Avoid false-positive memcpy() warning
platform/x86: ISST: use semi-colons instead of commas
platform/x86: asus-wmi: Fix "unsigned 'retval' is never less than zero" smatch warning
platform/x86: asus-wmi: Delete impossible condition
platform/x86: hp_accel: Convert to be a platform driver
platform/x86: hp_accel: Remove _INI method call
platform/mellanox: mlxbf-pmc: fix kernel-doc notation
platform/x86/intel: pmc/core: Add GBE Package C10 fix for Alder Lake PCH
platform/x86/intel: pmc/core: Add Alder Lake low power mode support for pmc core
platform/x86/intel: pmc/core: Add Latency Tolerance Reporting (LTR) support to Alder Lake
platform/x86/intel: pmc/core: Add Alderlake support to pmc core driver
platform/x86: intel-wmi-thunderbolt: Move to intel sub-directory
platform/x86: intel-wmi-sbl-fw-update: Move to intel sub-directory
platform/x86: intel-vbtn: Move to intel sub-directory
platform/x86: intel_oaktrail: Move to intel sub-directory
platform/x86: intel_int0002_vgpio: Move to intel sub-directory
platform/x86: intel-hid: Move to intel sub-directory
platform/x86: intel_atomisp2: Move to intel sub-directory
platform/x86: intel_speed_select_if: Move to intel sub-directory
...
Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did the
following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
The latter one will cause a tiny merge issue with your tree, as there
was a last-minute fix for this in 5.14 in your tree, but the fixup
should be "obvious". If you want me to provide a fixed merge for this,
please let me know.
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs
users at once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+FLQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXuACfWECnysDtXNe66DdETCFs1a1RToYAoMokWeU5
s8VFP1NY2BjmxJbkebLL
=8kVu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
Pull i2c updates from Wolfram Sang:
"I2C has a smaller pull reuest this time:
- new driver for I2C virtio
- removal of PMC SMP driver because platform is already gone
- IRQ probing and DMAENGINE API cleanups
- add SI metric prefix definitions to units.h
- beginning of i801 refactorization
- a few driver improvements"
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (28 commits)
i2c: cadence: Implement save restore
i2c: xlp9xx: fix main IRQ check
i2c: mt65xx: fix IRQ check
i2c: virtio: add a virtio i2c frontend driver
i2c: hix5hd2: fix IRQ check
i2c: s3c2410: fix IRQ check
i2c: iop3xx: fix deferred probing
i2c: synquacer: fix deferred probing
i2c: sun6i-pw2i: Prefer strscpy over strlcpy
i2c: remove dead PMC MSP TWI/SMBus/I2C driver
i2c: dev: Use sysfs_emit() in "show" functions
i2c: dev: Define pr_fmt() and drop duplication substrings
i2c: designware: Fix indentation in the header
i2c: designware: Use DIV_ROUND_CLOSEST() macro
units: Add SI metric prefix definitions
i2c: at91: mark PM ops as __maybe unused
i2c: sh_mobile: : use proper DMAENGINE API for termination
i2c: qup: : use proper DMAENGINE API for termination
i2c: mxs: : use proper DMAENGINE API for termination
i2c: imx: : use proper DMAENGINE API for termination
...
The zynqmp platform now supports chip-off so the registers can
lose context.
Implement save restore for i2c module.
Since we have only a couple of registers
an unconditional restore is done.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0 for the main IRQ, the driver's probe()
method will return 0 early (as if the method's call was successful).
Let's consider IRQ0 valid for simplicity -- devm_request_irq() can always
override that decision...
Fixes: 2bbd681ba2 ("i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: ce38815d39 ("I2C: mediatek: Add driver for MediaTek I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add an I2C bus driver for virtio para-virtualization.
The controller can be emulated by the backend driver in
any device model software by following the virtio protocol.
The device specification can be found on
https://lists.oasis-open.org/archives/virtio-comment/202101/msg00008.html.
By following the specification, people may implement different
backend drivers to emulate different controllers according to
their needs.
Co-developed-by: Conghui Chen <conghui.chen@intel.com>
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Signed-off-by: Jie Deng <jie.deng@intel.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: 15ef27756b ("i2c: hix5hd2: add i2c controller driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: e0d1ec9785 ("i2c-s3c2410: Change IRQ to be plain integer.")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When adding the code to handle platform_get_irq*() errors in the commit
489447380a ("handle errors returned by platform_get_irq*()"), the
actual error code was enforced to be -ENXIO in the driver for some
strange reason. This didn't matter much until the deferred probing was
introduced -- which requires an actual error code to be propagated
upstream from the failure site.
While fixing this, also stop overriding the errors from request_irq() to
-EIO (done since the pre-git era).
Fixes: 489447380a ("[PATCH] handle errors returned by platform_get_irq*()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
