With our current support for the new MIO PCI instructions, write
combining/write back MMIO memory can be obtained via the pci_iomap_wc()
and pci_iomap_wc_range() functions.
This is achieved by using the write back address for a specific bar
as provided in clp_store_query_pci_fn()
These functions are however not widely used and instead drivers often
rely on ioremap_wc() and ioremap_prot(), which on other platforms enable
write combining using a PTE flag set through the pgrprot value.
While we do not have a write combining flag in the low order flag bits
of the PTE like x86_64 does, with MIO support, there is a write back bit
in the physical address (bit 1 on z15) and thus also the PTE.
Which bit is used to toggle write back and whether it is available at
all, is however not fixed in the architecture. Instead we get this
information from the CLP Store Logical Processor Characteristics for PCI
command. When the write back bit is not provided we fall back to the
existing behavior.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
__qdio_allocate_fill_qdr() is meant to set up one specific queue
descriptor in the QDR. But for this simple task, it gets passed a bunch
of global structs and offsets - and then navigates through the structs
to find its actual operands.
Clean up all the complicated pointer chasing & index calculation, and
just pass a descriptor and its associated queue struct.
While at it also add some virt_to_phys() translations, to clarify that
addresses in the QDR are meant to be absolute.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Convert s390 to generic vDSO. There are a few special things on s390:
- vDSO can be called without a stack frame - glibc did this in the past.
So we need to allocate a stackframe on our own.
- The former assembly code used stcke to get the TOD clock and applied
time steering to it. We need to do the same in the new code. This is done
in the architecture specific __arch_get_hw_counter function. The steering
information is stored in an architecure specific area in the vDSO data.
- CPUCLOCK_VIRT is now handled with a syscall fallback, which might
be slower/less accurate than the old implementation.
The getcpu() function stays as an assembly function because there is no
generic implementation and the code is just a few lines.
Performance number from my system do 100 mio gettimeofday() calls:
Plain syscall: 8.6s
Generic VDSO: 1.3s
old ASM VDSO: 1s
So it's a bit slower but still much faster than syscalls.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add some coding style changes which hopefully make the code
look a bit less odd.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Use "|" instead of "+" within csum_fold() for consistency reasons,
like in the rest of the file.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Convert ip_fast_csum() so it doesn't call csum_partial(), but instead
open code the checksum calculation. The problem with csum_partial() is
that it makes use of the cksm instruction, which has high startup
costs and therefore is only very fast if used on larger memory
regions.
IPv4 headers however are small in size (5-16 32-bit words). The open
coded variant calculates the checksum in ~30% of the time compared to
the old variant (z14, march=z196).
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Rewrite csum_tcpudp_nofold() so that the generated code will not
contain branches. The old implementation was also optimized for
machines which came with "add logical with carry" instructions,
however the compiler doesn't generate them anymore. This is most
likely because those instructions are slower.
However with the old code the compiler generates a lot of branches,
which isn't too helpful usually. Therefore rewrite the code.
In a tight loop this doesn't make any difference since the branch
prediction unit does its job.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This implementation needs only ~30% of the time to calculate the
checksum compared to the generic variant. In addition the compiler
also generates only ~30% of the instructions compared to the generic
variant (on z14, compiled with march=z196).
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Since commit a21ee6055c ("lockdep: Change hardirq{s_enabled,_context}
to per-cpu variables") the lockdep code itself uses percpu variables. This
leads to recursions because the percpu macros are calling preempt_enable()
which might call trace_preempt_on().
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
quite a few architectures have the same csum_partial_copy_nocheck() -
simply memcpy() the data and then return the csum of the copy.
hexagon, parisc, ia64, s390, um: explicitly spelled out that way.
arc, arm64, csky, h8300, m68k/nommu, microblaze, mips/GENERIC_CSUM, nds32,
nios2, openrisc, riscv, unicore32: end up picking the same thing spelled
out in lib/checksum.h (with varying amounts of perversions along the way).
everybody else (alpha, arm, c6x, m68k/mmu, mips/!GENERIC_CSUM, powerpc,
sh, sparc, x86, xtensa) have non-generic variants. For all except c6x
the declaration is in their asm/checksum.h. c6x uses the wrapper
from asm-generic/checksum.h that would normally lead to the lib/checksum.h
instance, but in case of c6x we end up using an asm function from arch/c6x
instead.
Screw that mess - have architectures with private instances define
_HAVE_ARCH_CSUM_AND_COPY in their asm/checksum.h and have the default
one right in net/checksum.h conditional on _HAVE_ARCH_CSUM_AND_COPY
*not* defined.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
of truncating the most significant bits.
- Improve THP splitting required by qemu processes by making use of
walk_page_vma() instead of calling follow_page() for every single page
within each vma.
- Add missing ZCRYPT dependency to VFIO_AP to fix potential compile problems.
- Remove not required select CLOCKSOURCE_VALIDATE_LAST_CYCLE again.
- Set node distance to LOCAL_DISTANCE instead of 0, since e.g. libnuma
translates a node distance of 0 to "no NUMA support available".
- Couple of other minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----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=E0hf
-----END PGP SIGNATURE-----
Merge tag 's390-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- Allow s390 debug feature to handle finally more than 256 CPU numbers,
instead of truncating the most significant bits.
- Improve THP splitting required by qemu processes by making use of
walk_page_vma() instead of calling follow_page() for every single
page within each vma.
- Add missing ZCRYPT dependency to VFIO_AP to fix potential compile
problems.
- Remove not required select CLOCKSOURCE_VALIDATE_LAST_CYCLE again.
- Set node distance to LOCAL_DISTANCE instead of 0, since e.g. libnuma
translates a node distance of 0 to "no NUMA support available".
- Couple of other minor fixes and improvements.
* tag 's390-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/numa: move code to arch/s390/kernel
s390/time: remove select CLOCKSOURCE_VALIDATE_LAST_CYCLE again
s390/debug: debug feature version 3
s390/Kconfig: add missing ZCRYPT dependency to VFIO_AP
s390/numa: set node distance to LOCAL_DISTANCE
s390/pkey: remove redundant variable initialization
s390/test_unwind: fix possible memleak in test_unwind()
s390/gmap: improve THP splitting
s390/atomic: circumvent gcc 10 build regression
segment_eq is only used to implement uaccess_kernel. Just open code
uaccess_kernel in the arch uaccess headers and remove one layer of
indirection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Greentime Hu <green.hu@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Link: http://lkml.kernel.org/r/20200710135706.537715-5-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change __debug_entry structure in the following way:
- remove redundant union
- Field containing cpuid is expanded to 16 bits. 8-bit width was not
enough since we already support up to 512 cpus.
- Field containing the timestamp is expanded to 60 bits. The timestamp
itself is now stored in the absolute Unix time format in microseconds
taking the Epoch Index into acount.
Adjust default header for debug entries by setting minimum width for cpuid
to 4 digits.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The node distance is hardcoded to 0, which causes a trouble
for some user-level applications. In particular, "libnuma"
expects the distance of a node to itself as LOCAL_DISTANCE.
This update removes the offending node distance override.
Cc: <stable@vger.kernel.org> # 4.4
Fixes: 3a368f742d ("s390/numa: add core infrastructure")
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Patch series "mm: cleanup usage of <asm/pgalloc.h>"
Most architectures have very similar versions of pXd_alloc_one() and
pXd_free_one() for intermediate levels of page table. These patches add
generic versions of these functions in <asm-generic/pgalloc.h> and enable
use of the generic functions where appropriate.
In addition, functions declared and defined in <asm/pgalloc.h> headers are
used mostly by core mm and early mm initialization in arch and there is no
actual reason to have the <asm/pgalloc.h> included all over the place.
The first patch in this series removes unneeded includes of
<asm/pgalloc.h>
In the end it didn't work out as neatly as I hoped and moving
pXd_alloc_track() definitions to <asm-generic/pgalloc.h> would require
unnecessary changes to arches that have custom page table allocations, so
I've decided to move lib/ioremap.c to mm/ and make pgalloc-track.h local
to mm/.
This patch (of 8):
In most cases <asm/pgalloc.h> header is required only for allocations of
page table memory. Most of the .c files that include that header do not
use symbols declared in <asm/pgalloc.h> and do not require that header.
As for the other header files that used to include <asm/pgalloc.h>, it is
possible to move that include into the .c file that actually uses symbols
from <asm/pgalloc.h> and drop the include from the header file.
The process was somewhat automated using
sed -i -E '/[<"]asm\/pgalloc\.h/d' \
$(grep -L -w -f /tmp/xx \
$(git grep -E -l '[<"]asm/pgalloc\.h'))
where /tmp/xx contains all the symbols defined in
arch/*/include/asm/pgalloc.h.
[rppt@linux.ibm.com: fix powerpc warning]
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Link: http://lkml.kernel.org/r/20200627143453.31835-1-rppt@kernel.org
Link: http://lkml.kernel.org/r/20200627143453.31835-2-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86:
* Report last CPU for debugging
* Emulate smaller MAXPHYADDR in the guest than in the host
* .noinstr and tracing fixes from Thomas
* nested SVM page table switching optimization and fixes
Generic:
* Unify shadow MMU cache data structures across architectures
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl8pC+oUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNcOwgAjomqtEqQNlp7DdZT7VyyklzbxX1/
ud7v+oOJ8K4sFlf64lSthjPo3N9rzZCcw+yOXmuyuITngXOGc3tzIwXpCzpLtuQ1
WO1Ql3B/2dCi3lP5OMmsO1UAZqy9pKLg1dfeYUPk48P5+p7d/NPmk+Em5kIYzKm5
JsaHfCp2EEXomwmljNJ8PQ1vTjIQSSzlgYUBZxmCkaaX7zbEUMtxAQCStHmt8B84
33LczwXBm3viSWrzsoBV37I70+tseugiSGsCfUyupXOvq55d6D9FCqtCb45Hn4Vh
Ik8ggKdalsk/reiGEwNw1/3nr6mRMkHSbl+Mhc4waOIFf9dn0urgQgOaDg==
=YVx0
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"s390:
- implement diag318
x86:
- Report last CPU for debugging
- Emulate smaller MAXPHYADDR in the guest than in the host
- .noinstr and tracing fixes from Thomas
- nested SVM page table switching optimization and fixes
Generic:
- Unify shadow MMU cache data structures across architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (127 commits)
KVM: SVM: Fix sev_pin_memory() error handling
KVM: LAPIC: Set the TDCR settable bits
KVM: x86: Specify max TDP level via kvm_configure_mmu()
KVM: x86/mmu: Rename max_page_level to max_huge_page_level
KVM: x86: Dynamically calculate TDP level from max level and MAXPHYADDR
KVM: VXM: Remove temporary WARN on expected vs. actual EPTP level mismatch
KVM: x86: Pull the PGD's level from the MMU instead of recalculating it
KVM: VMX: Make vmx_load_mmu_pgd() static
KVM: x86/mmu: Add separate helper for shadow NPT root page role calc
KVM: VMX: Drop a duplicate declaration of construct_eptp()
KVM: nSVM: Correctly set the shadow NPT root level in its MMU role
KVM: Using macros instead of magic values
MIPS: KVM: Fix build error caused by 'kvm_run' cleanup
KVM: nSVM: remove nonsensical EXITINFO1 adjustment on nested NPF
KVM: x86: Add a capability for GUEST_MAXPHYADDR < HOST_MAXPHYADDR support
KVM: VMX: optimize #PF injection when MAXPHYADDR does not match
KVM: VMX: Add guest physical address check in EPT violation and misconfig
KVM: VMX: introduce vmx_need_pf_intercept
KVM: x86: update exception bitmap on CPUID changes
KVM: x86: rename update_bp_intercept to update_exception_bitmap
...
-----BEGIN PGP SIGNATURE-----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=ZcMq
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Herbert Xu made printk header file self-contained.
- Andy Shevchenko and Sergey Senozhatsky cleaned up console->setup()
error handling.
- Andy Shevchenko did some cleanups (e.g. sparse warning) in vsprintf
code.
- Minor documentation updates.
* tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
lib/vsprintf: Force type of flags value for gfp_t
lib/vsprintf: Replace custom spec to print decimals with generic one
lib/vsprintf: Replace hidden BUILD_BUG_ON() with static_assert()
printk: Make linux/printk.h self-contained
doc:kmsg: explicitly state the return value in case of SEEK_CUR
Replace HTTP links with HTTPS ones: vsprintf
hvc: unify console setup naming
console: Fix trivia typo 'change' -> 'chance'
console: Propagate error code from console ->setup()
tty: hvc: Return proper error code from console ->setup() hook
serial: sunzilog: Return proper error code from console ->setup() hook
serial: sunsab: Return proper error code from console ->setup() hook
mips: Return proper error code from console ->setup() hook
- LKMM updates: mostly documentation changes, but also some new litmus tests for atomic ops.
- KCSAN updates: the most important change is that GCC 11 now has all fixes in place
to support KCSAN, so GCC support can be enabled again. Also more annotations.
- futex updates: minor cleanups and simplifications
- seqlock updates: merge preparatory changes/cleanups for the 'associated locks' facilities.
- lockdep updates:
- simplify IRQ trace event handling
- add various new debug checks
- simplify header dependencies, split out <linux/lockdep_types.h>, decouple
lockdep from other low level headers some more
- fix NMI handling
- misc cleanups and smaller fixes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=3MTT
-----END PGP SIGNATURE-----
Merge tag 'locking-core-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
- LKMM updates: mostly documentation changes, but also some new litmus
tests for atomic ops.
- KCSAN updates: the most important change is that GCC 11 now has all
fixes in place to support KCSAN, so GCC support can be enabled again.
Also more annotations.
- futex updates: minor cleanups and simplifications
- seqlock updates: merge preparatory changes/cleanups for the
'associated locks' facilities.
- lockdep updates:
- simplify IRQ trace event handling
- add various new debug checks
- simplify header dependencies, split out <linux/lockdep_types.h>,
decouple lockdep from other low level headers some more
- fix NMI handling
- misc cleanups and smaller fixes
* tag 'locking-core-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
kcsan: Improve IRQ state trace reporting
lockdep: Refactor IRQ trace events fields into struct
seqlock: lockdep assert non-preemptibility on seqcount_t write
lockdep: Add preemption enabled/disabled assertion APIs
seqlock: Implement raw_seqcount_begin() in terms of raw_read_seqcount()
seqlock: Add kernel-doc for seqcount_t and seqlock_t APIs
seqlock: Reorder seqcount_t and seqlock_t API definitions
seqlock: seqcount_t latch: End read sections with read_seqcount_retry()
seqlock: Properly format kernel-doc code samples
Documentation: locking: Describe seqlock design and usage
locking/qspinlock: Do not include atomic.h from qspinlock_types.h
locking/atomic: Move ATOMIC_INIT into linux/types.h
lockdep: Move list.h inclusion into lockdep.h
locking/lockdep: Fix TRACE_IRQFLAGS vs. NMIs
futex: Remove unused or redundant includes
futex: Consistently use fshared as boolean
futex: Remove needless goto's
futex: Remove put_futex_key()
rwsem: fix commas in initialisation
docs: locking: Replace HTTP links with HTTPS ones
...
- Add support for custom exception handlers, as required by BPF_PROBE_MEM.
- Add support for BPF_PROBE_MEM.
- Add trace events for idle enter / exit for the s390 specific idle
implementation.
- Remove unused zcore memmmap device.
- Remove unused "raw view" from s390 debug feature.
- AP bus + zcrypt device driver code refactoring.
- Provide cex4 cca sysfs attributes for cex3 for zcrypt device driver.
- Expose only minimal interface to walk physmem for mm/memblock. This
is a common code change and it has been agreed on with Mike Rapoport
and Andrew Morton that this can go upstream via the s390 tree.
- Rework of the s390 vmem/vmmemap code to allow for future memory hot
remove.
- Get rid of FORCE_MAX_ZONEORDER to finally allow for order-10
allocations again, instead of only order-8 allocations.
- Various small improvements and fixes.
-----BEGIN PGP SIGNATURE-----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=H0KX
-----END PGP SIGNATURE-----
Merge tag 's390-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- Add support for function error injection.
- Add support for custom exception handlers, as required by
BPF_PROBE_MEM.
- Add support for BPF_PROBE_MEM.
- Add trace events for idle enter / exit for the s390 specific idle
implementation.
- Remove unused zcore memmmap device.
- Remove unused "raw view" from s390 debug feature.
- AP bus + zcrypt device driver code refactoring.
- Provide cex4 cca sysfs attributes for cex3 for zcrypt device driver.
- Expose only minimal interface to walk physmem for mm/memblock. This
is a common code change and it has been agreed on with Mike Rapoport
and Andrew Morton that this can go upstream via the s390 tree.
- Rework of the s390 vmem/vmmemap code to allow for future memory hot
remove.
- Get rid of FORCE_MAX_ZONEORDER to finally allow for order-10
allocations again, instead of only order-8 allocations.
- Various small improvements and fixes.
* tag 's390-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (48 commits)
s390/vmemmap: coding style updates
s390/vmemmap: avoid memset(PAGE_UNUSED) when adding consecutive sections
s390/vmemmap: remember unused sub-pmd ranges
s390/vmemmap: fallback to PTEs if mapping large PMD fails
s390/vmem: cleanup empty page tables
s390/vmemmap: take the vmem_mutex when populating/freeing
s390/vmemmap: cleanup when vmemmap_populate() fails
s390/vmemmap: extend modify_pagetable() to handle vmemmap
s390/vmem: consolidate vmem_add_range() and vmem_remove_range()
s390/vmem: rename vmem_add_mem() to vmem_add_range()
s390: enable HAVE_FUNCTION_ERROR_INJECTION
s390/pci: clarify comment in s390_mmio_read/write
s390/time: improve comparison for tod steering
s390/time: select CLOCKSOURCE_VALIDATE_LAST_CYCLE
s390/time: use CLOCKSOURCE_MASK
s390/bpf: implement BPF_PROBE_MEM
s390/kernel: expand exception table logic to allow new handling options
s390/kernel: unify EX_TABLE* implementations
s390/mm: allow order 10 allocations
s390/mm: avoid trimming to MAX_ORDER
...
This patch moves ATOMIC_INIT from asm/atomic.h into linux/types.h.
This allows users of atomic_t to use ATOMIC_INIT without having to
include atomic.h as that way may lead to header loops.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Waiman Long <longman@redhat.com>
Link: https://lkml.kernel.org/r/20200729123105.GB7047@gondor.apana.org.au
As it stands if you include printk.h by itself it will fail to
compile because it requires definitions from ratelimit.h. However,
simply including ratelimit.h from printk.h does not work due to
inclusion loops involving sched.h and kernel.h.
This patch solves this by moving bits from ratelimit.h into a new
header file which can then be included by printk.h without any
worries about header loops.
The build bot then revealed some intriguing failures arising out
of this patch. On s390 there is an inclusion loop with asm/bug.h
and linux/kernel.h that triggers a compile failure, because kernel.h
will cause asm-generic/bug.h to be included before s390's own
asm/bug.h has finished processing. This has been fixed by not
including kernel.h in arch/s390/include/asm/bug.h.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Petr Mladek <pmladek@suse.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Link: https://lore.kernel.org/r/20200721062248.GA18383@gondor.apana.org.au
This kernel feature is required for enabling BPF_KPROBE_OVERRIDE.
Define override_function_with_return() and regs_set_return_value()
functions, and fix compile errors in syscall_wrapper.h.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
This is a s390 port of commit 548acf1923 ("x86/mm: Expand the
exception table logic to allow new handling options"), which is needed
for implementing BPF_PROBE_MEM on s390.
The new handler field is made 64-bit in order to allow pointing from
dynamically allocated entries to handlers in kernel text. Unlike on x86,
NULL is used instead of ex_handler_default. This is because exception
tables are used by boot/text_dma.S, and it would be a pain to preserve
ex_handler_default.
The new infrastructure is ignored in early_pgm_check_handler, since
there is no pt_regs.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Replace three implementations with one using using __stringify_in_c
macro conveniently "borrowed" from powerpc and microblaze.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In order to use <asm/percpu.h> in irqflags.h, we need to make sure
asm/percpu.h does not itself depend on irqflags.h
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200623083721.396143816@infradead.org
Move x86's 'struct kvm_mmu_memory_cache' to common code in anticipation
of moving the entire x86 implementation code to common KVM and reusing
it for arm64 and MIPS. Add a new architecture specific asm/kvm_types.h
to control the existence and parameters of the struct. The new header
is needed to avoid a chicken-and-egg problem with asm/kvm_host.h as all
architectures define instances of the struct in their vCPU structs.
Add an asm-generic version of kvm_types.h to avoid having empty files on
PPC and s390 in the long term, and for arm64 and mips in the short term.
Suggested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-15-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl8DWosUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroO8cAf/UskNg8qoLGG17rQwhFpmigSllbiJ
TAyi3tpb1Y0Z2MfYeGkeiEb1L34bS28Cxl929DoqI3hrXy1wDCmsHPB5c3URXrzd
aswvr7pJtQV9iH1ykaS2woFJnOUovMFsFYMhj46yUPoAvdKOZKvuqcduxbogYHFw
YeRhS+1lGfiP2A0j3O/nnNJ0wq+FxKO46G3CgWeqG75+FSL6y/tl0bZJUMKKajQZ
GNaOv/CYCHAfUdvgy0ZitRD8lV8yxng3dYGjm+a52Kmn2ZWiFlxNrnxzHySk16Rn
Lq6MfFOqgrYpoZv7SnsFYnRE05U5bEFQ8BGr22fImQ+ktKDgq+9gv6cKwA==
=+DN/
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Bugfixes and a one-liner patch to silence a sparse warning"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm64: Stop clobbering x0 for HVC_SOFT_RESTART
KVM: arm64: PMU: Fix per-CPU access in preemptible context
KVM: VMX: Use KVM_POSSIBLE_CR*_GUEST_BITS to initialize guest/host masks
KVM: x86: Mark CR4.TSD as being possibly owned by the guest
KVM: x86: Inject #GP if guest attempts to toggle CR4.LA57 in 64-bit mode
kvm: use more precise cast and do not drop __user
KVM: x86: bit 8 of non-leaf PDPEs is not reserved
KVM: X86: Fix async pf caused null-ptr-deref
KVM: arm64: vgic-v4: Plug race between non-residency and v4.1 doorbell
KVM: arm64: pvtime: Ensure task delay accounting is enabled
KVM: arm64: Fix kvm_reset_vcpu() return code being incorrect with SVE
KVM: arm64: Annotate hyp NMI-related functions as __always_inline
KVM: s390: reduce number of IO pins to 1
Some beautifications related to the internal only used
struct ap_message and related code. Instead of one int carrying
only the special flag now a u32 flags field is used.
At struct CPRBX the pointers to additional data are now marked
with __user. This caused some changes needed on code, where
these structs are also used within the zcrypt misc functions.
The ica_rsa_* structs now use the generic types __u8, __u32, ...
instead of char, unsigned int.
zcrypt_msg6 and zcrypt_msg50 use min_t() instead of min().
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
I can't come up with a satisfying reason why we still need the memory
segment list. We used to represent in the list:
- boot memory
- standby memory added via add_memory()
- loaded dcss segments
When loading/unloading dcss segments, we already track them in a
separate list and check for overlaps
(arch/s390/mm/extmem.c:segment_overlaps_others()) when loading segments.
The overlap check was introduced for some segments in
commit b2300b9efe ("[S390] dcssblk: add >2G DCSSs support and stacked
contiguous DCSSs support.")
and was extended to cover all dcss segments in
commit ca57114609 ("s390/extmem: remove code for 31 bit addressing
mode").
Although I doubt that overlaps with boot memory and standby memory
are relevant, let's reshuffle the checks in load_segment() to request
the resource first. This will bail out in case we have overlaps with
other resources (esp. boot memory and standby memory). The order
is now different compared to segment_unload() and segment_unload(), but
that should not matter.
This smells like a leftover from ancient times, let's get rid of it. We
can now convert vmem_remove_mapping() into a void function - everybody
ignored the return value already.
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200625150029.45019-1-david@redhat.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Tested-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [DCSS]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
There is no interface to userspace which exposes anything that would
require the struct __debug_entry definition. Therefore remove it from
uapi. This allows to change the definition, since it is only kernel
internally used.
The only exception is the crash utility, however that tool must handle
changes all the time anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
There is not a single user of the debug raw view. Therefore remove it
before anybody uses it. If anybody would make use of the view it would
expose the struct __debug_entry definition to userspace and really
would make it uapi. This wouldn't be good, since the definition is
suboptimal and needs to be changed.
Right now the structure definition is only defined to be uapi, however
there is no user.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
DIAGNOSE 0x318 (diag318) sets information regarding the environment
the VM is running in (Linux, z/VM, etc) and is observed via
firmware/service events.
This is a privileged s390x instruction that must be intercepted by
SIE. Userspace handles the instruction as well as migration. Data
is communicated via VCPU register synchronization.
The Control Program Name Code (CPNC) is stored in the SIE block. The
CPNC along with the Control Program Version Code (CPVC) are stored
in the kvm_vcpu_arch struct.
This data is reset on load normal and clear resets.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200622154636.5499-3-walling@linux.ibm.com
[borntraeger@de.ibm.com: fix sync_reg position]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The diag 318 struct introduced in include/asm/diag.h can be
reused in KVM, so let's condense the version code fields in the
diag318_info struct for easier usage and simplify it until we
can determine how the data should be formatted.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20200622154636.5499-2-walling@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The current number of KVM_IRQCHIP_NUM_PINS results in an order 3
allocation (32kb) for each guest start/restart. This can result in OOM
killer activity even with free swap when the memory is fragmented
enough:
kernel: qemu-system-s39 invoked oom-killer: gfp_mask=0x440dc0(GFP_KERNEL_ACCOUNT|__GFP_COMP|__GFP_ZERO), order=3, oom_score_adj=0
kernel: CPU: 1 PID: 357274 Comm: qemu-system-s39 Kdump: loaded Not tainted 5.4.0-29-generic #33-Ubuntu
kernel: Hardware name: IBM 8562 T02 Z06 (LPAR)
kernel: Call Trace:
kernel: ([<00000001f848fe2a>] show_stack+0x7a/0xc0)
kernel: [<00000001f8d3437a>] dump_stack+0x8a/0xc0
kernel: [<00000001f8687032>] dump_header+0x62/0x258
kernel: [<00000001f8686122>] oom_kill_process+0x172/0x180
kernel: [<00000001f8686abe>] out_of_memory+0xee/0x580
kernel: [<00000001f86e66b8>] __alloc_pages_slowpath+0xd18/0xe90
kernel: [<00000001f86e6ad4>] __alloc_pages_nodemask+0x2a4/0x320
kernel: [<00000001f86b1ab4>] kmalloc_order+0x34/0xb0
kernel: [<00000001f86b1b62>] kmalloc_order_trace+0x32/0xe0
kernel: [<00000001f84bb806>] kvm_set_irq_routing+0xa6/0x2e0
kernel: [<00000001f84c99a4>] kvm_arch_vm_ioctl+0x544/0x9e0
kernel: [<00000001f84b8936>] kvm_vm_ioctl+0x396/0x760
kernel: [<00000001f875df66>] do_vfs_ioctl+0x376/0x690
kernel: [<00000001f875e304>] ksys_ioctl+0x84/0xb0
kernel: [<00000001f875e39a>] __s390x_sys_ioctl+0x2a/0x40
kernel: [<00000001f8d55424>] system_call+0xd8/0x2c8
As far as I can tell s390x does not use the iopins as we bail our for
anything other than KVM_IRQ_ROUTING_S390_ADAPTER and the chip/pin is
only used for KVM_IRQ_ROUTING_IRQCHIP. So let us use a small number to
reduce the memory footprint.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200617083620.5409-1-borntraeger@de.ibm.com
If both the tracer and the tracee are compat processes, and gprs[2]
is assigned a value by __poke_user_compat, then the higher 32 bits
of gprs[2] are cleared, IS_ERR_VALUE() always returns false, and
syscall_get_error() always returns 0.
Fix the implementation by sign-extending the value for compat processes
the same way as x86 implementation does.
The bug was exposed to user space by commit 201766a20e ("ptrace: add
PTRACE_GET_SYSCALL_INFO request") and detected by strace test suite.
This change fixes strace syscall tampering on s390.
Link: https://lkml.kernel.org/r/20200602180051.GA2427@altlinux.org
Fixes: 753c4dd6a2 ("[S390] ptrace changes")
Cc: Elvira Khabirova <lineprinter@altlinux.org>
Cc: stable@vger.kernel.org # v2.6.28+
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
clock_getres in the vDSO library has to preserve the same behaviour
of posix_get_hrtimer_res().
In particular, posix_get_hrtimer_res() does:
sec = 0;
ns = hrtimer_resolution;
and hrtimer_resolution depends on the enablement of the high
resolution timers that can happen either at compile or at run time.
Fix the s390 vdso implementation of clock_getres keeping a copy of
hrtimer_resolution in vdso data and using that directly.
Link: https://lkml.kernel.org/r/20200324121027.21665-1-vincenzo.frascino@arm.com
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[heiko.carstens@de.ibm.com: use llgf for proper zero extension]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Loongson port
PPC:
- Fixes
ARM:
- Fixes
x86:
- KVM_SET_USER_MEMORY_REGION optimizations
- Fixes
- Selftest fixes
The guest side of the asynchronous page fault work has been delayed to 5.9
in order to sync with Thomas's interrupt entry rework.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl7icj4UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPHGQgAj9+5j+f5v06iMP/+ponWwsVfh+5/
UR1gPbpMSFMKF0U+BCFxsBeGKWPDiz9QXaLfy6UGfOFYBI475Su5SoZ8/i/o6a2V
QjcKIJxBRNs66IG/774pIpONY8/mm/3b6vxmQktyBTqjb6XMGlOwoGZixj/RTp85
+uwSICxMlrijg+fhFMwC4Bo/8SFg+FeBVbwR07my88JaLj+3cV/NPolG900qLSa6
uPqJ289EQ86LrHIHXCEWRKYvwy77GFsmBYjKZH8yXpdzUlSGNexV8eIMAz50figu
wYRJGmHrRqwuzFwEGknv8SA3s2HVggXO4WVkWWCeJyO8nIVfYFUhME5l6Q==
=+Hh0
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
"The guest side of the asynchronous page fault work has been delayed to
5.9 in order to sync with Thomas's interrupt entry rework, but here's
the rest of the KVM updates for this merge window.
MIPS:
- Loongson port
PPC:
- Fixes
ARM:
- Fixes
x86:
- KVM_SET_USER_MEMORY_REGION optimizations
- Fixes
- Selftest fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (62 commits)
KVM: x86: do not pass poisoned hva to __kvm_set_memory_region
KVM: selftests: fix sync_with_host() in smm_test
KVM: async_pf: Inject 'page ready' event only if 'page not present' was previously injected
KVM: async_pf: Cleanup kvm_setup_async_pf()
kvm: i8254: remove redundant assignment to pointer s
KVM: x86: respect singlestep when emulating instruction
KVM: selftests: Don't probe KVM_CAP_HYPERV_ENLIGHTENED_VMCS when nested VMX is unsupported
KVM: selftests: do not substitute SVM/VMX check with KVM_CAP_NESTED_STATE check
KVM: nVMX: Consult only the "basic" exit reason when routing nested exit
KVM: arm64: Move hyp_symbol_addr() to kvm_asm.h
KVM: arm64: Synchronize sysreg state on injecting an AArch32 exception
KVM: arm64: Make vcpu_cp1x() work on Big Endian hosts
KVM: arm64: Remove host_cpu_context member from vcpu structure
KVM: arm64: Stop sparse from moaning at __hyp_this_cpu_ptr
KVM: arm64: Handle PtrAuth traps early
KVM: x86: Unexport x86_fpu_cache and make it static
KVM: selftests: Ignore KVM 5-level paging support for VM_MODE_PXXV48_4K
KVM: arm64: Save the host's PtrAuth keys in non-preemptible context
KVM: arm64: Stop save/restoring ACTLR_EL1
KVM: arm64: Add emulation for 32bit guests accessing ACTLR2
...
'Page not present' event may or may not get injected depending on
guest's state. If the event wasn't injected, there is no need to
inject the corresponding 'page ready' event as the guest may get
confused. E.g. Linux thinks that the corresponding 'page not present'
event wasn't delivered *yet* and allocates a 'dummy entry' for it.
This entry is never freed.
Note, 'wakeup all' events have no corresponding 'page not present'
event and always get injected.
s390 seems to always be able to inject 'page not present', the
change is effectively a nop.
Suggested-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200610175532.779793-2-vkuznets@redhat.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=208081
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All architectures define pte_index() as
(address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1)
and all architectures define pte_offset_kernel() as an entry in the array
of PTEs indexed by the pte_index().
For the most architectures the pte_offset_kernel() implementation relies
on the availability of pmd_page_vaddr() that converts a PMD entry value to
the virtual address of the page containing PTEs array.
Let's move x86 definitions of the PTE accessors to the generic place in
<linux/pgtable.h> and then simply drop the respective definitions from the
other architectures.
The architectures that didn't provide pmd_page_vaddr() are updated to have
that defined.
The generic implementation of pte_offset_kernel() can be overridden by an
architecture and alpha makes use of this because it has special ordering
requirements for its version of pte_offset_kernel().
[rppt@linux.ibm.com: v2]
Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org
[rppt@linux.ibm.com: update]
Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org
[rppt@linux.ibm.com: update]
Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org
[akpm@linux-foundation.org: fix x86 warning]
[sfr@canb.auug.org.au: fix powerpc build]
Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The replacement of <asm/pgrable.h> with <linux/pgtable.h> made the include
of the latter in the middle of asm includes. Fix this up with the aid of
the below script and manual adjustments here and there.
import sys
import re
if len(sys.argv) is not 3:
print "USAGE: %s <file> <header>" % (sys.argv[0])
sys.exit(1)
hdr_to_move="#include <linux/%s>" % sys.argv[2]
moved = False
in_hdrs = False
with open(sys.argv[1], "r") as f:
lines = f.readlines()
for _line in lines:
line = _line.rstrip('
')
if line == hdr_to_move:
continue
if line.startswith("#include <linux/"):
in_hdrs = True
elif not moved and in_hdrs:
moved = True
print hdr_to_move
print line
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-4-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mm: consolidate definitions of page table accessors", v2.
The low level page table accessors (pXY_index(), pXY_offset()) are
duplicated across all architectures and sometimes more than once. For
instance, we have 31 definition of pgd_offset() for 25 supported
architectures.
Most of these definitions are actually identical and typically it boils
down to, e.g.
static inline unsigned long pmd_index(unsigned long address)
{
return (address >> PMD_SHIFT) & (PTRS_PER_PMD - 1);
}
static inline pmd_t *pmd_offset(pud_t *pud, unsigned long address)
{
return (pmd_t *)pud_page_vaddr(*pud) + pmd_index(address);
}
These definitions can be shared among 90% of the arches provided
XYZ_SHIFT, PTRS_PER_XYZ and xyz_page_vaddr() are defined.
For architectures that really need a custom version there is always
possibility to override the generic version with the usual ifdefs magic.
These patches introduce include/linux/pgtable.h that replaces
include/asm-generic/pgtable.h and add the definitions of the page table
accessors to the new header.
This patch (of 12):
The linux/mm.h header includes <asm/pgtable.h> to allow inlining of the
functions involving page table manipulations, e.g. pte_alloc() and
pmd_alloc(). So, there is no point to explicitly include <asm/pgtable.h>
in the files that include <linux/mm.h>.
The include statements in such cases are remove with a simple loop:
for f in $(git grep -l "include <linux/mm.h>") ; do
sed -i -e '/include <asm\/pgtable.h>/ d' $f
done
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-1-rppt@kernel.org
Link: http://lkml.kernel.org/r/20200514170327.31389-2-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the
pdev->no_vf_scan flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio
and qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl7eVGcACgkQjYWKoQLX
FBhweQgAkicvx31x230rdfG+jQkQkl0UqF99vvWrJHEll77SqadfjzKAGIjUB+K0
EoeHVD5Wcj7BogDGcyHeQ0bZpu4WzE+y1nmnrsvu7TEEvcBmkJH0rF2jF+y0sb/O
3qvwFkX/CB5OqaMzKC/AEeRpcCKR+ZUXkWu1irbYth7CBXaycD9EAPc4cj8CfYGZ
r5njUdYOVk77TaO4aV+t5pCYc5TCRJaWXSsWaAv/nuLcIqsFBYOy2q+L47zITGXp
utZVanIDjzx+ikpaKicOIfC3hJsRuNX9MnlZKsQFwpVEZAUZmIUm29XdhGJTWSxU
RV7m1ORINbFP1nGAqWqkOvGo/LC0ZA==
=VhXR
-----END PGP SIGNATURE-----
Merge tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the pdev->no_vf_scan
flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio and
qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
* tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (52 commits)
vfio-ccw: make vfio_ccw_regops variables declarations static
vfio-ccw: Add trace for CRW event
vfio-ccw: Wire up the CRW irq and CRW region
vfio-ccw: Introduce a new CRW region
vfio-ccw: Refactor IRQ handlers
vfio-ccw: Introduce a new schib region
vfio-ccw: Refactor the unregister of the async regions
vfio-ccw: Register a chp_event callback for vfio-ccw
vfio-ccw: Introduce new helper functions to free/destroy regions
vfio-ccw: document possible errors
vfio-ccw: Enable transparent CCW IPL from DASD
s390/pci: Log new handle in clp_disable_fh()
s390/cio, s390/qeth: cleanup PNSO CHSC
s390/qdio: remove q->first_to_kick
s390/qdio: fix up qdio_start_irq() kerneldoc
s390: remove critical section cleanup from entry.S
s390: add machine check SIGP
s390/pci: ioremap() align with generic code
s390/ap: introduce new ap function ap_get_qdev()
Documentation/s390: Update / remove developerWorks web links
...
- Support for userspace to send requests directly to the on-chip GZIP
accelerator on Power9.
- Rework of our lockless page table walking (__find_linux_pte()) to make it
safe against parallel page table manipulations without relying on an IPI for
serialisation.
- A series of fixes & enhancements to make our machine check handling more
robust.
- Lots of plumbing to add support for "prefixed" (64-bit) instructions on
Power10.
- Support for using huge pages for the linear mapping on 8xx (32-bit).
- Remove obsolete Xilinx PPC405/PPC440 support, and an associated sound driver.
- Removal of some obsolete 40x platforms and associated cruft.
- Initial support for booting on Power10.
- Lots of other small features, cleanups & fixes.
Thanks to:
Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan, Andrey Abramov,
Aneesh Kumar K.V, Balamuruhan S, Bharata B Rao, Bulent Abali, Cédric Le
Goater, Chen Zhou, Christian Zigotzky, Christophe JAILLET, Christophe Leroy,
Dmitry Torokhov, Emmanuel Nicolet, Erhard F., Gautham R. Shenoy, Geoff Levand,
George Spelvin, Greg Kurz, Gustavo A. R. Silva, Gustavo Walbon, Haren Myneni,
Hari Bathini, Joel Stanley, Jordan Niethe, Kajol Jain, Kees Cook, Leonardo
Bras, Madhavan Srinivasan., Mahesh Salgaonkar, Markus Elfring, Michael
Neuling, Michal Simek, Nathan Chancellor, Nathan Lynch, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pingfan Liu, Qian Cai, Ram
Pai, Raphael Moreira Zinsly, Ravi Bangoria, Sam Bobroff, Sandipan Das, Segher
Boessenkool, Stephen Rothwell, Sukadev Bhattiprolu, Tyrel Datwyler, Wolfram
Sang, Xiongfeng Wang.
-----BEGIN PGP SIGNATURE-----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=o0WU
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Support for userspace to send requests directly to the on-chip GZIP
accelerator on Power9.
- Rework of our lockless page table walking (__find_linux_pte()) to
make it safe against parallel page table manipulations without
relying on an IPI for serialisation.
- A series of fixes & enhancements to make our machine check handling
more robust.
- Lots of plumbing to add support for "prefixed" (64-bit) instructions
on Power10.
- Support for using huge pages for the linear mapping on 8xx (32-bit).
- Remove obsolete Xilinx PPC405/PPC440 support, and an associated sound
driver.
- Removal of some obsolete 40x platforms and associated cruft.
- Initial support for booting on Power10.
- Lots of other small features, cleanups & fixes.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan,
Andrey Abramov, Aneesh Kumar K.V, Balamuruhan S, Bharata B Rao, Bulent
Abali, Cédric Le Goater, Chen Zhou, Christian Zigotzky, Christophe
JAILLET, Christophe Leroy, Dmitry Torokhov, Emmanuel Nicolet, Erhard F.,
Gautham R. Shenoy, Geoff Levand, George Spelvin, Greg Kurz, Gustavo A.
R. Silva, Gustavo Walbon, Haren Myneni, Hari Bathini, Joel Stanley,
Jordan Niethe, Kajol Jain, Kees Cook, Leonardo Bras, Madhavan
Srinivasan., Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Michal
Simek, Nathan Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin,
Oliver O'Halloran, Paul Mackerras, Pingfan Liu, Qian Cai, Ram Pai,
Raphael Moreira Zinsly, Ravi Bangoria, Sam Bobroff, Sandipan Das, Segher
Boessenkool, Stephen Rothwell, Sukadev Bhattiprolu, Tyrel Datwyler,
Wolfram Sang, Xiongfeng Wang.
* tag 'powerpc-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (299 commits)
powerpc/pseries: Make vio and ibmebus initcalls pseries specific
cxl: Remove dead Kconfig options
powerpc: Add POWER10 architected mode
powerpc/dt_cpu_ftrs: Add MMA feature
powerpc/dt_cpu_ftrs: Enable Prefixed Instructions
powerpc/dt_cpu_ftrs: Advertise support for ISA v3.1 if selected
powerpc: Add support for ISA v3.1
powerpc: Add new HWCAP bits
powerpc/64s: Don't set FSCR bits in INIT_THREAD
powerpc/64s: Save FSCR to init_task.thread.fscr after feature init
powerpc/64s: Don't let DT CPU features set FSCR_DSCR
powerpc/64s: Don't init FSCR_DSCR in __init_FSCR()
powerpc/32s: Fix another build failure with CONFIG_PPC_KUAP_DEBUG
powerpc/module_64: Use special stub for _mcount() with -mprofile-kernel
powerpc/module_64: Simplify check for -mprofile-kernel ftrace relocations
powerpc/module_64: Consolidate ftrace code
powerpc/32: Disable KASAN with pages bigger than 16k
powerpc/uaccess: Don't set KUEP by default on book3s/32
powerpc/uaccess: Don't set KUAP by default on book3s/32
powerpc/8xx: Reduce time spent in allow_user_access() and friends
...
Pull livepatching updates from Jiri Kosina:
- simplifications and improvements for issues Peter Ziljstra found
during his previous work on W^X cleanups.
This allows us to remove livepatch arch-specific .klp.arch sections
and add proper support for jump labels in patched code.
Also, this patchset removes the last module_disable_ro() usage in the
tree.
Patches from Josh Poimboeuf and Peter Zijlstra
- a few other minor cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching:
MAINTAINERS: add lib/livepatch to LIVE PATCHING
livepatch: add arch-specific headers to MAINTAINERS
livepatch: Make klp_apply_object_relocs static
MAINTAINERS: adjust to livepatch .klp.arch removal
module: Make module_enable_ro() static again
x86/module: Use text_mutex in apply_relocate_add()
module: Remove module_disable_ro()
livepatch: Remove module_disable_ro() usage
x86/module: Use text_poke() for late relocations
s390/module: Use s390_kernel_write() for late relocations
s390: Change s390_kernel_write() return type to match memcpy()
livepatch: Prevent module-specific KLP rela sections from referencing vmlinux symbols
livepatch: Remove .klp.arch
livepatch: Apply vmlinux-specific KLP relocations early
livepatch: Disallow vmlinux.ko
Merge more updates from Andrew Morton:
"More mm/ work, plenty more to come
Subsystems affected by this patch series: slub, memcg, gup, kasan,
pagealloc, hugetlb, vmscan, tools, mempolicy, memblock, hugetlbfs,
thp, mmap, kconfig"
* akpm: (131 commits)
arm64: mm: use ARCH_HAS_DEBUG_WX instead of arch defined
x86: mm: use ARCH_HAS_DEBUG_WX instead of arch defined
riscv: support DEBUG_WX
mm: add DEBUG_WX support
drivers/base/memory.c: cache memory blocks in xarray to accelerate lookup
mm/thp: rename pmd_mknotpresent() as pmd_mkinvalid()
powerpc/mm: drop platform defined pmd_mknotpresent()
mm: thp: don't need to drain lru cache when splitting and mlocking THP
hugetlbfs: get unmapped area below TASK_UNMAPPED_BASE for hugetlbfs
sparc32: register memory occupied by kernel as memblock.memory
include/linux/memblock.h: fix minor typo and unclear comment
mm, mempolicy: fix up gup usage in lookup_node
tools/vm/page_owner_sort.c: filter out unneeded line
mm: swap: memcg: fix memcg stats for huge pages
mm: swap: fix vmstats for huge pages
mm: vmscan: limit the range of LRU type balancing
mm: vmscan: reclaim writepage is IO cost
mm: vmscan: determine anon/file pressure balance at the reclaim root
mm: balance LRU lists based on relative thrashing
mm: only count actual rotations as LRU reclaim cost
...
There are multiple similar definitions for arch_clear_hugepage_flags() on
various platforms. Lets just add it's generic fallback definition for
platforms that do not override. This help reduce code duplication.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1588907271-11920-4-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are multiple similar definitions for is_hugepage_only_range() on
various platforms. Lets just add it's generic fallback definition for
platforms that do not override. This help reduce code duplication.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1588907271-11920-3-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
- Move the arch-specific code into arch/arm64/kvm
- Start the post-32bit cleanup
- Cherry-pick a few non-invasive pre-NV patches
x86:
- Rework of TLB flushing
- Rework of event injection, especially with respect to nested virtualization
- Nested AMD event injection facelift, building on the rework of generic code
and fixing a lot of corner cases
- Nested AMD live migration support
- Optimization for TSC deadline MSR writes and IPIs
- Various cleanups
- Asynchronous page fault cleanups (from tglx, common topic branch with tip tree)
- Interrupt-based delivery of asynchronous "page ready" events (host side)
- Hyper-V MSRs and hypercalls for guest debugging
- VMX preemption timer fixes
s390:
- Cleanups
Generic:
- switch vCPU thread wakeup from swait to rcuwait
The other architectures, and the guest side of the asynchronous page fault
work, will come next week.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl7VJcYUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPf6QgAq4wU5wdd1lTGz/i3DIhNVJNJgJlp
ozLzRdMaJbdbn5RpAK6PEBd9+pt3+UlojpFB3gpJh2Nazv2OzV4yLQgXXXyyMEx1
5Hg7b4UCJYDrbkCiegNRv7f/4FWDkQ9dx++RZITIbxeskBBCEI+I7GnmZhGWzuC4
7kj4ytuKAySF2OEJu0VQF6u0CvrNYfYbQIRKBXjtOwuRK4Q6L63FGMJpYo159MBQ
asg3B1jB5TcuGZ9zrjL5LkuzaP4qZZHIRs+4kZsH9I6MODHGUxKonrkablfKxyKy
CFK+iaHCuEXXty5K0VmWM3nrTfvpEjVjbMc7e1QGBQ5oXsDM0pqn84syRg==
=v7Wn
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- Move the arch-specific code into arch/arm64/kvm
- Start the post-32bit cleanup
- Cherry-pick a few non-invasive pre-NV patches
x86:
- Rework of TLB flushing
- Rework of event injection, especially with respect to nested
virtualization
- Nested AMD event injection facelift, building on the rework of
generic code and fixing a lot of corner cases
- Nested AMD live migration support
- Optimization for TSC deadline MSR writes and IPIs
- Various cleanups
- Asynchronous page fault cleanups (from tglx, common topic branch
with tip tree)
- Interrupt-based delivery of asynchronous "page ready" events (host
side)
- Hyper-V MSRs and hypercalls for guest debugging
- VMX preemption timer fixes
s390:
- Cleanups
Generic:
- switch vCPU thread wakeup from swait to rcuwait
The other architectures, and the guest side of the asynchronous page
fault work, will come next week"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (256 commits)
KVM: selftests: fix rdtsc() for vmx_tsc_adjust_test
KVM: check userspace_addr for all memslots
KVM: selftests: update hyperv_cpuid with SynDBG tests
x86/kvm/hyper-v: Add support for synthetic debugger via hypercalls
x86/kvm/hyper-v: enable hypercalls regardless of hypercall page
x86/kvm/hyper-v: Add support for synthetic debugger interface
x86/hyper-v: Add synthetic debugger definitions
KVM: selftests: VMX preemption timer migration test
KVM: nVMX: Fix VMX preemption timer migration
x86/kvm/hyper-v: Explicitly align hcall param for kvm_hyperv_exit
KVM: x86/pmu: Support full width counting
KVM: x86/pmu: Tweak kvm_pmu_get_msr to pass 'struct msr_data' in
KVM: x86: announce KVM_FEATURE_ASYNC_PF_INT
KVM: x86: acknowledgment mechanism for async pf page ready notifications
KVM: x86: interrupt based APF 'page ready' event delivery
KVM: introduce kvm_read_guest_offset_cached()
KVM: rename kvm_arch_can_inject_async_page_present() to kvm_arch_can_dequeue_async_page_present()
KVM: x86: extend struct kvm_vcpu_pv_apf_data with token info
Revert "KVM: async_pf: Fix #DF due to inject "Page not Present" and "Page Ready" exceptions simultaneously"
KVM: VMX: Replace zero-length array with flexible-array
...
Pull uaccess/csum updates from Al Viro:
"Regularize the sitation with uaccess checksum primitives:
- fold csum_partial_... into csum_and_copy_..._user()
- on x86 collapse several access_ok()/stac()/clac() into
user_access_begin()/user_access_end()"
* 'uaccess.csum' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
default csum_and_copy_to_user(): don't bother with access_ok()
take the dummy csum_and_copy_from_user() into net/checksum.h
arm: switch to csum_and_copy_from_user()
sh32: convert to csum_and_copy_from_user()
m68k: convert to csum_and_copy_from_user()
xtensa: switch to providing csum_and_copy_from_user()
sparc: switch to providing csum_and_copy_from_user()
parisc: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
alpha: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
ia64: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
ia64: csum_partial_copy_nocheck(): don't abuse csum_partial_copy_from_user()
x86: switch 32bit csum_and_copy_to_user() to user_access_{begin,end}()
x86: switch both 32bit and 64bit to providing csum_and_copy_from_user()
x86_64: csum_..._copy_..._user(): switch to unsafe_..._user()
get rid of csum_partial_copy_to_user()
If two page ready notifications happen back to back the second one is not
delivered and the only mechanism we currently have is
kvm_check_async_pf_completion() check in vcpu_run() loop. The check will
only be performed with the next vmexit when it happens and in some cases
it may take a while. With interrupt based page ready notification delivery
the situation is even worse: unlike exceptions, interrupts are not handled
immediately so we must check if the slot is empty. This is slow and
unnecessary. Introduce dedicated MSR_KVM_ASYNC_PF_ACK MSR to communicate
the fact that the slot is free and host should check its notification
queue. Mandate using it for interrupt based 'page ready' APF event
delivery.
As kvm_check_async_pf_completion() is going away from vcpu_run() we need
a way to communicate the fact that vcpu->async_pf.done queue has
transitioned from empty to non-empty state. Introduce
kvm_arch_async_page_present_queued() and KVM_REQ_APF_READY to do the job.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200525144125.143875-7-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An innocent reader of the following x86 KVM code:
bool kvm_arch_can_inject_async_page_present(struct kvm_vcpu *vcpu)
{
if (!(vcpu->arch.apf.msr_val & KVM_ASYNC_PF_ENABLED))
return true;
...
may get very confused: if APF mechanism is not enabled, why do we report
that we 'can inject async page present'? In reality, upon injection
kvm_arch_async_page_present() will check the same condition again and,
in case APF is disabled, will just drop the item. This is fine as the
guest which deliberately disabled APF doesn't expect to get any APF
notifications.
Rename kvm_arch_can_inject_async_page_present() to
kvm_arch_can_dequeue_async_page_present() to make it clear what we are
checking: if the item can be dequeued (meaning either injected or just
dropped).
On s390 kvm_arch_can_inject_async_page_present() always returns 'true' so
the rename doesn't matter much.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200525144125.143875-4-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
now that can be done conveniently - all non-trivial cases have
_HAVE_ARCH_COPY_AND_CSUM_FROM_USER defined, so the fallback in
net/checksum.h is used only for dummy (copy_from_user, then
csum_partial) implementation. Allowing us to get rid of all
dummy instances, both of csum_and_copy_from_user() and
csum_partial_copy_from_user().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
CHSC3D (PNSO - perform network subchannel operation) is used for
OC0 (Store-network-bridging-information) as well as for
OC3 (Store-network-address-information). So common fields are renamed
from *brinfo* to *pnso*.
Also *_bridge_host_* is changed into *_addr_change_*, e.g.
qeth_bridge_host_event to qeth_addr_change_event, for the
same reasons.
The keywords in the card traces are changed accordingly.
Remove unused L3 types, as PNSO will only return Layer2 entries.
Make PNSO CHSC implementation more consistent with existing API usage:
Add new function ccw_device_pnso() to drivers/s390/cio/device_ops.c and
the function declaration to arch/s390/include/asm/ccwdev.h, which takes
a struct ccw_device * as parameter instead of schid and calls
chsc_pnso().
PNSO CHSC has no strict relationship to qdio. So move the calling
function from qdio to qeth_l2 and move the necessary structures to a
new file arch/s390/include/asm/chsc.h.
Do response code evaluation only in chsc_error_from_response() and
use return code in all other places. qeth_anset_makerc() was meant to
evaluate the PNSO response code, but never did, because pnso_rc was
already non-zero.
Indentation was corrected in some places.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The current code is rather complex and caused a lot of subtle
and hard to debug bugs in the past. Simplify the code by calling
the system_call handler with interrupts disabled, save
machine state, and re-enable them later.
This requires significant changes to the machine check handling code
as well. When the machine check interrupt arrived while being in kernel
mode the new code will signal pending machine checks with a SIGP external
call. When userspace was interrupted, the handler will switch to the
kernel stack and directly execute s390_handle_mcck().
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This will be used with the upcoming entry.S changes to signal
that there's a machine check pending that cannot be handled in
the Machine check handler itself.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's use the same signature and parameter names as in the generic
ioremap() definition making the physical address' type explicit.
Add a check against address wrap around as in the generic
lib/ioremap.c:ioremap_prot() code.
Finally use free_vm_area() instead of vunmap() as in the generic code.
Besides being clearer free_vm_area() can also skip a few additional
checks compared with vunmap().
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
On s390 PCI Virtual Functions (VFs) are scanned by firmware and are made
available to Linux via the hot-plug interface. As such the common code
path of doing the scan directly using the parent Physical Function (PF)
is not used and fenced off with the no_vf_scan attribute.
Even if the partition created the VFs itself e.g. using the sriov_numvfs
attribute of a PF, the PF/VF links thus need to be established after the
fact. To do this when a VF is plugged we scan through all functions on
the same zbus and test whether they are the parent PF in which case we
establish the necessary links.
With these links established there is now no more need to fence off
pci_iov_remove_virtfn() for pdev->no_vf_scan as the common code now
works fine.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Link: https://lore.kernel.org/r/20200506154139.90609-3-schnelle@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
commit 5e1fb45ec8 ("s390/ccwgroup: remove pm support") removed power
management support from the ccwgroup bus driver. So remove the
associated callbacks from all ccwgroup drivers.
CC: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new stats for exposing halt-polling cpu usage:
halt_poll_success_ns
halt_poll_fail_ns
Thus sum of these 2 stats is the total cpu time spent polling. "success"
means the VCPU polled until a virtual interrupt was delivered. "fail"
means the VCPU had to schedule out (either because the maximum poll time
was reached or it needed to yield the CPU).
To avoid touching every arch's kvm_vcpu_stat struct, only update and
export halt-polling cpu usage stats if we're on x86.
Exporting cpu usage as a u64 and in nanoseconds means we will overflow at
~500 years, which seems reasonably large.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Jon Cargille <jcargill@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <20200508182240.68440-1-jcargill@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The s390_mmio_read/write syscalls are currently broken when running with
MIO.
The new pcistb_mio/pcstg_mio/pcilg_mio instructions are executed
similiarly to normal load/store instructions and do address translation
in the current address space. That means inside the kernel they are
aware of mappings into kernel address space while outside the kernel
they use user space mappings (usually created through mmap'ing a PCI
device file).
Now when existing user space applications use the s390_pci_mmio_write
and s390_pci_mmio_read syscalls, they pass I/O addresses that are mapped
into user space so as to be usable with the new instructions without
needing a syscall. Accessing these addresses with the old instructions
as done currently leads to a kernel panic.
Also, for such a user space mapping there may not exist an equivalent
kernel space mapping which means we can't just use the new instructions
in kernel space.
Instead of replicating user mappings in the kernel which then might
collide with other mappings, we can conceptually execute the new
instructions as if executed by the user space application using the
secondary address space. This even allows us to directly store to the
user pointer without the need for copy_to/from_user().
Cc: stable@vger.kernel.org
Fixes: 71ba41c9b1 ("s390/pci: provide support for MIO instructions")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
s390_kernel_write()'s function type is almost identical to memcpy().
Change its return type to "void *" so they can be used interchangeably.
Cc: linux-s390@vger.kernel.org
Cc: heiko.carstens@de.ibm.com
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Acked-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> # s390
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Recognize IPL Block's Ipl Type of "nvme". Populate related structs and sysfs
entries.
Signed-off-by: Jason J. Herne <jjherne@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
We allow multiple functions on a single bus.
We suppress the ZPCI_DEVFN definition and replace its
occurences with zpci->devfn.
We verify the number of device during the registration.
There can never be more domains in use than existing
devices, so we do not need to verify the count of domain
after having verified the count of devices.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The current PCI implementation do not provide a bus resource.
This leads to a notice being print at boot.
Let's do it more nicely and provide the bus resource.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The zPCI bus is in charge to handle common zPCI resources for
zPCI devices.
Creating the zPCI bus, the PCI bus, the zPCI devices and the
PCI devices and hotplug slots
done in a specific order:
- PCI hotplug slot creation needs a PCI bus
- PCI bus needs a PCI domain
which is reported by the pci_domain_nr() when setting up the
host bridge
- PCI domain is set from the zPCI with devfn 0
this is necessary to have a reproducible enumeration
Therefore we can not create devices or hotplug slots for any PCI
device associated with a zPCI device before having discovered
the function zero of the bus.
The discovery and initialization of devices can be done at several
points in the code:
- On Events, serialized in a thread context
- On initialization, in the kernel init thread context
- When powering on the hotplug slot, in a user thread context
The removal of devices and their parent bus may also be done on
events or for devices when powering down the slot.
To guarantee the existence of the bus and devices until they are
no more needed we use kref in zPCI bus and introduce a reference
count in the zPCI devices.
In this patch the zPCI bus still only accept a device with
a devfn 0.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Firmware provides the bus/devfn part of the PCI addresses of a zPCI
function inside the new field RID of the CLP query PCI function
with a bit to know if this field is available to use.
Let's add these fields to the clp_rsp_query_pci structure,
add corresponding fields to zdev and initialize them.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Using PCI multifunctions in S390 is a new feature we may want
to ignore to continue provide the same topology as in the past
to userland even if the configuration supports exposing the
topology of a multi-Function device.
A new boolean parameters allows to overwrite the kernel
pci configuration:
- pci=norid when on, disallow the use a new firmware field,
RID, which provides the PCI <bus>:<device>.<function> part
of the PCI address.
To be used in the following patches and satisfy the checkpatch.pl
the variable is exposed in pci.h
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
In the future the bus sysdata may not directly point to the
zpci_dev.
In preparation of upcoming patches let us abstract the
access to the zpci_dev from the device inside the pci device.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add SysFS attribute that provides the port number for PCI functions
representing a single port of a multi-port device.
Signed-off-by: Alexander Schmidt <alexs@linux.ibm.com>
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Merge yet more updates from Andrew Morton:
- Almost all of the rest of MM (memcg, slab-generic, slab, pagealloc,
gup, hugetlb, pagemap, memremap)
- Various other things (hfs, ocfs2, kmod, misc, seqfile)
* akpm: (34 commits)
ipc/util.c: sysvipc_find_ipc() should increase position index
kernel/gcov/fs.c: gcov_seq_next() should increase position index
fs/seq_file.c: seq_read(): add info message about buggy .next functions
drivers/dma/tegra20-apb-dma.c: fix platform_get_irq.cocci warnings
change email address for Pali Rohár
selftests: kmod: test disabling module autoloading
selftests: kmod: fix handling test numbers above 9
docs: admin-guide: document the kernel.modprobe sysctl
fs/filesystems.c: downgrade user-reachable WARN_ONCE() to pr_warn_once()
kmod: make request_module() return an error when autoloading is disabled
mm/memremap: set caching mode for PCI P2PDMA memory to WC
mm/memory_hotplug: add pgprot_t to mhp_params
powerpc/mm: thread pgprot_t through create_section_mapping()
x86/mm: introduce __set_memory_prot()
x86/mm: thread pgprot_t through init_memory_mapping()
mm/memory_hotplug: rename mhp_restrictions to mhp_params
mm/memory_hotplug: drop the flags field from struct mhp_restrictions
mm/special: create generic fallbacks for pte_special() and pte_mkspecial()
mm/vma: introduce VM_ACCESS_FLAGS
mm/vma: define a default value for VM_DATA_DEFAULT_FLAGS
...
There are many platforms with exact same value for VM_DATA_DEFAULT_FLAGS
This creates a default value for VM_DATA_DEFAULT_FLAGS in line with the
existing VM_STACK_DEFAULT_FLAGS. While here, also define some more
macros with standard VMA access flag combinations that are used
frequently across many platforms. Apart from simplification, this
reduces code duplication as well.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Chris Zankel <chris@zankel.net>
Link: http://lkml.kernel.org/r/1583391014-8170-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Upper-layer drivers allocate their SBALs by calling qdio_alloc_buffers()
for each individual queue. But when later passing the SBAL addresses to
qdio_establish(), they need to be in a single array of pointers.
So if the driver uses multiple Input or Output queues, it needs to
allocate a temporary array just to present all its SBAL pointers in this
layout.
This patch slightly changes the format of the QDIO initialization data,
so that drivers can pass a per-queue array where each element points to
a queue's SBAL array.
zfcp doesn't use multiple queues, so the impact there is trivial.
For qeth this brings a nice reduction in complexity, and removes
a page-sized allocation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
All that qdio_allocate() actually uses from the init_data is the cdev,
and the number of Input and Output Queues. Have the driver pass those as
parameters, and defer the init_data processing into qdio_establish().
This includes writing per-device(!) trace entries, and most of the
sanity checks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth Vijayan
common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other fixes/improvements
in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios
mm cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl6Ig2YACgkQjYWKoQLX
FBj2gggAibnHOl9d0ngX1mVT4nz51R3V8z5sEQjNMr2uHBmaTqs7pi/00gaFMxoC
NngVEXvL443jSogQivthGgXPpRCV9xdKE3sp38j7fF4LgHoeuDtGd1oaX4W9Rqk0
7Yii35EaO2e2WHdOKaAbu+ZvDRunFjERyntc51MYaIUivFosogSo07vC73vFIArF
VGStS09fJ4Ny76ott896T7Ulx1Iek/MkF1vponEMLGNUIcLIQbbxZxOwgz0pHuEF
SlyyJBnhOIaAJGOYlKREQDt1cew+hsxluPU+a01bwdsmdZv9LH1BGwLayDqTH58i
QWvtEpzJFmDvo9jGM1v81ebaGnyCKg==
=hiGF
-----END PGP SIGNATURE-----
Merge tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth
Vijayan common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other
fixes/improvements in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios mm
cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
* tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (57 commits)
s390/mm: cleanup init_new_context() callback
s390/mm: cleanup virtual memory constants usage
s390/mm: remove page table downgrade support
s390/qdio: set qdio_irq->cdev at allocation time
s390/qdio: remove unused function declarations
s390/ccwgroup: remove pm support
s390/ap: remove power management code from ap bus and drivers
s390/zcrypt: use kvmalloc instead of kmalloc for 256k alloc
s390/mm: cleanup arch_get_unmapped_area() and friends
s390/ism: remove pm support
s390/cio: use fallthrough;
s390/vfio: use fallthrough;
s390/zcrypt: use fallthrough;
s390: use fallthrough;
s390/cpum_sf: Fix wrong page count in error message
s390/diag: fix display of diagnose call statistics
s390/ap: Remove ap device suspend and resume callbacks
s390/pci: Improve handling of unset UID
s390/pci: Fix zpci_alloc_domain() over allocation
s390/qdio: pass ISC as parameter to chsc_sadc()
...
* GICv4.1 support
* 32bit host removal
PPC:
* secure (encrypted) using under the Protected Execution Framework
ultravisor
s390:
* allow disabling GISA (hardware interrupt injection) and protected
VMs/ultravisor support.
x86:
* New dirty bitmap flag that sets all bits in the bitmap when dirty
page logging is enabled; this is faster because it doesn't require bulk
modification of the page tables.
* Initial work on making nested SVM event injection more similar to VMX,
and less buggy.
* Various cleanups to MMU code (though the big ones and related
optimizations were delayed to 5.8). Instead of using cr3 in function
names which occasionally means eptp, KVM too has standardized on "pgd".
* A large refactoring of CPUID features, which now use an array that
parallels the core x86_features.
* Some removal of pointer chasing from kvm_x86_ops, which will also be
switched to static calls as soon as they are available.
* New Tigerlake CPUID features.
* More bugfixes, optimizations and cleanups.
Generic:
* selftests: cleanups, new MMU notifier stress test, steal-time test
* CSV output for kvm_stat.
KVM/MIPS has been broken since 5.5, it does not compile due to a patch committed
by MIPS maintainers. I had already prepared a fix, but the MIPS maintainers
prefer to fix it in generic code rather than KVM so they are taking care of it.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl6GOnIUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMfxwf/ZKLZiRoaovXCOG71M/eHtQb8ZIqU
3MPy+On3eC5Sk/aBxWUL9EFZsbYG6kYdbZ1VOvG9XPBoLlnkDSm/IR0kaELHtnjj
oGVda/tvGn46Ne39y8xBptmb91WDcWH0vFthT/CwlMxAw3xjr+gG7Qyo+8F2CW6m
SSSuLiHSBnyO1cQKruBTHZ8qnR8LlnfXEqtd6Y4LFLic0LbLIoIdRcT3wjQrcZrm
Djd7wbTEYZjUfoqZ72ekwEDUsONcDLDSKcguDO9pSMSCGhpxCVT5Vy68KRpoIMs2
nzNWDKjvqQo5zb2+GWxJgkd12Hv+n7PCXZMbVrWBu1pQsewUns9m4mkpGw==
=6fGt
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- GICv4.1 support
- 32bit host removal
PPC:
- secure (encrypted) using under the Protected Execution Framework
ultravisor
s390:
- allow disabling GISA (hardware interrupt injection) and protected
VMs/ultravisor support.
x86:
- New dirty bitmap flag that sets all bits in the bitmap when dirty
page logging is enabled; this is faster because it doesn't require
bulk modification of the page tables.
- Initial work on making nested SVM event injection more similar to
VMX, and less buggy.
- Various cleanups to MMU code (though the big ones and related
optimizations were delayed to 5.8). Instead of using cr3 in
function names which occasionally means eptp, KVM too has
standardized on "pgd".
- A large refactoring of CPUID features, which now use an array that
parallels the core x86_features.
- Some removal of pointer chasing from kvm_x86_ops, which will also
be switched to static calls as soon as they are available.
- New Tigerlake CPUID features.
- More bugfixes, optimizations and cleanups.
Generic:
- selftests: cleanups, new MMU notifier stress test, steal-time test
- CSV output for kvm_stat"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (277 commits)
x86/kvm: fix a missing-prototypes "vmread_error"
KVM: x86: Fix BUILD_BUG() in __cpuid_entry_get_reg() w/ CONFIG_UBSAN=y
KVM: VMX: Add a trampoline to fix VMREAD error handling
KVM: SVM: Annotate svm_x86_ops as __initdata
KVM: VMX: Annotate vmx_x86_ops as __initdata
KVM: x86: Drop __exit from kvm_x86_ops' hardware_unsetup()
KVM: x86: Copy kvm_x86_ops by value to eliminate layer of indirection
KVM: x86: Set kvm_x86_ops only after ->hardware_setup() completes
KVM: VMX: Configure runtime hooks using vmx_x86_ops
KVM: VMX: Move hardware_setup() definition below vmx_x86_ops
KVM: x86: Move init-only kvm_x86_ops to separate struct
KVM: Pass kvm_init()'s opaque param to additional arch funcs
s390/gmap: return proper error code on ksm unsharing
KVM: selftests: Fix cosmetic copy-paste error in vm_mem_region_move()
KVM: Fix out of range accesses to memslots
KVM: X86: Micro-optimize IPI fastpath delay
KVM: X86: Delay read msr data iff writes ICR MSR
KVM: PPC: Book3S HV: Add a capability for enabling secure guests
KVM: arm64: GICv4.1: Expose HW-based SGIs in debugfs
KVM: arm64: GICv4.1: Allow non-trapping WFI when using HW SGIs
...
Change a header to mandatory-y if both of the following are met:
[1] At least one architecture (except um) specifies it as generic-y in
arch/*/include/asm/Kbuild
[2] Every architecture (except um) either has its own implementation
(arch/*/include/asm/*.h) or specifies it as generic-y in
arch/*/include/asm/Kbuild
This commit was generated by the following shell script.
----------------------------------->8-----------------------------------
arches=$(cd arch; ls -1 | sed -e '/Kconfig/d' -e '/um/d')
tmpfile=$(mktemp)
grep "^mandatory-y +=" include/asm-generic/Kbuild > $tmpfile
find arch -path 'arch/*/include/asm/Kbuild' |
xargs sed -n 's/^generic-y += \(.*\)/\1/p' | sort -u |
while read header
do
mandatory=yes
for arch in $arches
do
if ! grep -q "generic-y += $header" arch/$arch/include/asm/Kbuild &&
! [ -f arch/$arch/include/asm/$header ]; then
mandatory=no
break
fi
done
if [ "$mandatory" = yes ]; then
echo "mandatory-y += $header" >> $tmpfile
for arch in $arches
do
sed -i "/generic-y += $header/d" arch/$arch/include/asm/Kbuild
done
fi
done
sed -i '/^mandatory-y +=/d' include/asm-generic/Kbuild
LANG=C sort $tmpfile >> include/asm-generic/Kbuild
----------------------------------->8-----------------------------------
One obvious benefit is the diff stat:
25 files changed, 52 insertions(+), 557 deletions(-)
It is tedious to list generic-y for each arch that needs it.
So, mandatory-y works like a fallback default (by just wrapping
asm-generic one) when arch does not have a specific header
implementation.
See the following commits:
def3f7cefea1b39bae16
It is tedious to convert headers one by one, so I processed by a shell
script.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/20200210175452.5030-1-masahiroy@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued user-access cleanups in the futex code.
- percpu-rwsem rewrite that uses its own waitqueue and atomic_t
instead of an embedded rwsem. This addresses a couple of
weaknesses, but the primary motivation was complications on the -rt
kernel.
- Introduce raw lock nesting detection on lockdep
(CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
lock differences. This too originates from -rt.
- Reuse lockdep zapped chain_hlocks entries, to conserve RAM
footprint on distro-ish kernels running into the "BUG:
MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
chain-entries pool.
- Misc cleanups, smaller fixes and enhancements - see the changelog
for details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
Documentation/locking/locktypes: Minor copy editor fixes
Documentation/locking/locktypes: Further clarifications and wordsmithing
m68knommu: Remove mm.h include from uaccess_no.h
x86: get rid of user_atomic_cmpxchg_inatomic()
generic arch_futex_atomic_op_inuser() doesn't need access_ok()
x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
objtool: whitelist __sanitizer_cov_trace_switch()
[parisc, s390, sparc64] no need for access_ok() in futex handling
sh: no need of access_ok() in arch_futex_atomic_op_inuser()
futex: arch_futex_atomic_op_inuser() calling conventions change
completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
lockdep: Add posixtimer context tracing bits
lockdep: Annotate irq_work
lockdep: Add hrtimer context tracing bits
lockdep: Introduce wait-type checks
completion: Use simple wait queues
sched/swait: Prepare usage in completions
...
The set of values asce_limit may be assigned with is TASK_SIZE_MAX,
_REGION1_SIZE, _REGION2_SIZE and 0 as a special case if the callback
was called from execve().
Do VM_BUG_ON() if asce_limit is something else.
Save few CPU cycles by removing unnecessary asce_limit re-assignment
in case of 3-level task and redundant PGD entry type reconstruction.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This update consolidates page table handling code. Because
there are hardly any 31-bit binaries left we do not need to
optimize for that.
No extra efforts are needed to ensure that a compat task does
not map anything above 2GB. The TASK_SIZE limit for 31-bit
tasks is 2GB already and the generic code does check that a
resulting map address would not surpass that limit.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Move access_ok() in and pagefault_enable()/pagefault_disable() out.
Mechanical conversion only - some instances don't really need
a separate access_ok() at all (e.g. the ones only using
get_user()/put_user(), or architectures where access_ok()
is always true); we'll deal with that in followups.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Factor out check_asce_limit() function and fix few style
defects in arch_get_unmapped_area() family of functions.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
[heiko.carstens@de.ibm.com: small coding style changes]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- mark sie control block as 512 byte aligned
- use fallthrough;
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=nsOM
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: cleanups for 5.7
- mark sie control block as 512 byte aligned
- use fallthrough;
When the support for polling drivers was initially added, it only
considered Input Queue 0. But as QDIO interrupts are actually for the
full device and not a single queue, this doesn't really fit for
configurations where multiple Input Queues are used.
Rework the qdio code so that interrupts for a polling driver are not
split up into actions for each queue. Instead deliver the interrupt as
a single event, and let the driver decide which queue needs what action.
When re-enabling the QDIO interrupt via qdio_start_irq(), this means
that the qdio code needs to
(1) put _all_ eligible queues back into a state where they raise IRQs,
(2) and afterwards check _all_ eligible queues for new work to bridge
the race window.
On the qeth side of things (as the only qdio polling driver), we can now
add CQ polling support to the main NAPI poll routine. It doesn't consume
NAPI budget, and to avoid hogging the CPU we yield control after
completing one full queue worth of buffers.
The subsequent qdio_start_irq() will check for any additional work, and
have us re-schedule the NAPI instance accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sie block must be aligned to 512 bytes. Mark it as such.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
When UID checking is enabled a UID value of 0 is invalid and can not be
set by the user. On z/VM it is however used to indicate an unset UID.
Until now, this lead to the behavior that one PCI function could be
attached with UID 0 after which z/VM would prohibit further attachment.
Now if the user then turns off UID checking in z/VM the user could
seemingly attach additional PCI functions that would however not show up
in Linux as that would not be informed of the change in UID checking
mode. This is unexpected and confusing and lead to bug reports against
Linux.
Instead now, if we encounter an unset UID value of 0 treat it as
indicating that UID checking was turned off, switch to automatic domain
allocation, and warn the user of the possible misconfiguration.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Until now zpci_alloc_domain() only prevented more than
CONFIG_PCI_NR_FUNCTIONS from being added when using automatic domain
allocation. When explicit UIDs were defined UIDs above
CONFIG_PCI_NR_FUNCTIONS were not counted at all.
When more PCI functions are added this could lead to various errors
including under sized IRQ vectors and similar issues.
Fix this by explicitly tracking the number of allocated domains.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Show number of cores that run at least one SMT thread
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Re-IPL for both CCW and FCP is currently done by using diag 308 with the
"Load Clear" subcode, which means that all memory will be cleared.
This can increase re-IPL duration considerably on very large machines.
For CCW devices, there is also a "Load Normal" subcode that was only used
for dump kernels so far. For FCP devices, a similar "Load Normal" subcode
was introduced with z14. The "Load Normal" diag 308 subcode allows to
re-IPL without clearing memory.
This patch adds a new "clear" sysfs attribute to /sys/firmware/reipl for
both the ccw and fcp subdirectories, which can be set to either "0" or "1"
to disable or enable re-IPL with memory clearing. The default value is "0",
which disables memory clearing.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The CPU topology masks on s390 contain also bits of CPUs which
are offline. Currently this is already a problem, since common
code scheduler expects e.g. cpu_smt_mask() to reflect reality.
This update changes the described behaviour and s390 starts to
behave like all other architectures.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Variable cpus_with_topology is a leftover that became
unneeded once the fake NUMA support has been removed.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Show CPU physical address as reported by STAP instruction
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
1. Allow to disable gisa
2. protected virtual machines
Protected VMs (PVM) are KVM VMs, where KVM can't access the VM's
state like guest memory and guest registers anymore. Instead the
PVMs are mostly managed by a new entity called Ultravisor (UV),
which provides an API, so KVM and the PV can request management
actions.
PVMs are encrypted at rest and protected from hypervisor access
while running. They switch from a normal operation into protected
mode, so we can still use the standard boot process to load a
encrypted blob and then move it into protected mode.
Rebooting is only possible by passing through the unprotected/normal
mode and switching to protected again.
One mm related patch will go via Andrews mm tree ( mm/gup/writeback:
add callbacks for inaccessible pages)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=x6Hn
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Features and Enhancements for 5.7 part1
1. Allow to disable gisa
2. protected virtual machines
Protected VMs (PVM) are KVM VMs, where KVM can't access the VM's
state like guest memory and guest registers anymore. Instead the
PVMs are mostly managed by a new entity called Ultravisor (UV),
which provides an API, so KVM and the PV can request management
actions.
PVMs are encrypted at rest and protected from hypervisor access
while running. They switch from a normal operation into protected
mode, so we can still use the standard boot process to load a
encrypted blob and then move it into protected mode.
Rebooting is only possible by passing through the unprotected/normal
mode and switching to protected again.
One mm related patch will go via Andrews mm tree ( mm/gup/writeback:
add callbacks for inaccessible pages)
Now that all callers of kvm_free_memslot() pass NULL for @dont, remove
the param from the top-level routine and all arch's implementations.
No functional change intended.
Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When userspace executes a syscall or gets interrupted,
BEAR contains a kernel address when returning to userspace.
This make it pretty easy to figure out where the kernel is
mapped even with KASLR enabled. To fix this, add lpswe to
lowcore and always execute it there, so userspace sees only
the lowcore address of lpswe. For this we have to extend
both critical_cleanup and the SWITCH_ASYNC macro to also check
for lpswe addresses in lowcore.
Fixes: b2d24b97b2 ("s390/kernel: add support for kernel address space layout randomization (KASLR)")
Cc: <stable@vger.kernel.org> # v5.2+
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Embedding the hotplug_slot in zdev structure allows to
greatly simplify the hotplug handling by eliminating
the handling of the slot_list.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Make page, frame, virtual and physical address conversion macros
more expressive by avoiding redundant definitions and defining
new macros using existing ones.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
On s390 there currently is no implementation of pud_write(). That was ok
as long as we had our own implementation of get_user_pages_fast() which
checked for pud protection by testing the bit directly w/o using
pud_write(). The other callers of pud_write() are not reachable on s390.
After commit 1a42010cdc ("s390/mm: convert to the generic
get_user_pages_fast code") we use the generic get_user_pages_fast(), which
does call pud_write() in pud_access_permitted() for FOLL_WRITE access on
a large pud. Without an s390 specific pud_write(), the generic version is
called, which contains a BUG() statement to remind us that we don't have a
proper implementation. This results in a kernel panic.
Fix this by providing an implementation of pud_write().
Cc: <stable@vger.kernel.org> # 5.2+
Fixes: 1a42010cdc ("s390/mm: convert to the generic get_user_pages_fast code")
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
For protected VMs, the VCPU resets are done by the Ultravisor, as KVM
has no access to the VCPU registers.
Note that the ultravisor will only accept a call for the exact reset
that has been requested.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Code 5 for the set cpu state UV call tells the UV to load a PSW from
the SE header (first IPL) or from guest location 0x0 (diag 308 subcode
0/1). Also it sets the cpu into operating state afterwards, so we can
start it.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
VCPU states have to be reported to the ultravisor for SIGP
interpretation, kdump, kexec and reboot.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
diag 308 subcode 0 and 1 require several KVM and Ultravisor interactions.
Specific to these "soft" reboots are
* The "unshare all" UVC
* The "prepare for reset" UVC
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The SPX instruction is handled by the ultravisor. We do get a
notification intercept, though. Let us update our internal view.
In addition to that, when the guest prefix page is not secure, an
intercept 112 (0x70) is indicated. Let us make the prefix pages
secure again.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Now that we can't access guest memory anymore, we have a dedicated
satellite block that's a bounce buffer for instruction data.
We re-use the memop interface to copy the instruction data to / from
userspace. This lets us re-use a lot of QEMU code which used that
interface to make logical guest memory accesses which are not possible
anymore in protected mode anyway.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Guest registers for protected guests are stored at offset 0x380. We
will copy those to the usual places. Long term we could refactor this
or use register access functions.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The sclp interrupt is kind of special. The ultravisor polices that we
do not inject an sclp interrupt with payload if no sccb is outstanding.
On the other hand we have "asynchronous" event interrupts, e.g. for
console input.
We separate both variants into sclp interrupt and sclp event interrupt.
The sclp interrupt is masked until a previous servc instruction has
finished (sie exit 108).
[frankja@linux.ibm.com: factoring out write_sclp]
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This defines the necessary data structures in the SIE control block to
inject machine checks,external and I/O interrupts. We first define the
the interrupt injection control, which defines the next interrupt to
inject. Then we define the fields that contain the payload for machine
checks,external and I/O interrupts.
This is then used to implement interruption injection for the following
list of interruption types:
- I/O (uses inject io interruption)
__deliver_io
- External (uses inject external interruption)
__deliver_cpu_timer
__deliver_ckc
__deliver_emergency_signal
__deliver_external_call
- cpu restart (uses inject restart interruption)
__deliver_restart
- machine checks (uses mcic, failing address and external damage)
__write_machine_check
Please note that posted interrupts (GISA) are not used for protected
guests as of today.
The service interrupt is handled in a followup patch.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We have two new SIE exit codes dealing with instructions.
104 (0x68) for a secure instruction interception, on which the SIE needs
hypervisor action to complete the instruction. We can piggy-back on the
existing instruction handlers.
108 which is merely a notification and provides data for tracking and
management. For example this is used to tell the host about a new value
for the prefix register. As there will be several special case handlers
in later patches, we handle this in a separate function.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Since there is no interception for load control and load psw
instruction in the protected mode, we need a new way to get notified
whenever we can inject an IRQ right after the guest has just enabled
the possibility for receiving them.
The new interception codes solve that problem by providing a
notification for changes to IRQ enablement relevant bits in CRs 0, 6
and 14, as well a the machine check mask bit in the PSW.
No special handling is needed for these interception codes, the KVM
pre-run code will consult all necessary CRs and PSW bits and inject
IRQs the guest is enabled for.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Before we destroy the secure configuration, we better make all
pages accessible again. This also happens during reboot, where we reboot
into a non-secure guest that then can go again into secure mode. As
this "new" secure guest will have a new ID we cannot reuse the old page
state.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
KSM will not work on secure pages, because when the kernel reads a
secure page, it will be encrypted and hence no two pages will look the
same.
Let's mark the guest pages as unmergeable when we transition to secure
mode.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This contains 3 main changes:
1. changes in SIE control block handling for secure guests
2. helper functions for create/destroy/unpack secure guests
3. KVM_S390_PV_COMMAND ioctl to allow userspace dealing with secure
machines
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This adds two new helper functions for doing UV CALLs.
The first variant handles UV CALLs that might have longer busy
conditions or just need longer when doing partial completion. We should
schedule when necessary.
The second variant handles UV CALLs that only need the handle but have
no payload (e.g. destroying a VM). We can provide a simple wrapper for
those.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The adapter interrupt page containing the indicator bits is currently
pinned. That means that a guest with many devices can pin a lot of
memory pages in the host. This also complicates the reference tracking
which is needed for memory management handling of protected virtual
machines. It might also have some strange side effects for madvise
MADV_DONTNEED and other things.
We can simply try to get the userspace page set the bits and free the
page. By storing the userspace address in the irq routing entry instead
of the guest address we can actually avoid many lookups and list walks
so that this variant is very likely not slower.
If userspace messes around with the memory slots the worst thing that
can happen is that we write to some other memory within that process.
As we get the the page with FOLL_WRITE this can also not be used to
write to shared read-only pages.
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch simplification]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This provides the basic ultravisor calls and page table handling to cope
with secure guests:
- provide arch_make_page_accessible
- make pages accessible after unmapping of secure guests
- provide the ultravisor commands convert to/from secure
- provide the ultravisor commands pin/unpin shared
- provide callbacks to make pages secure (inacccessible)
- we check for the expected pin count to only make pages secure if the
host is not accessing them
- we fence hugetlbfs for secure pages
- add missing radix-tree include into gmap.h
The basic idea is that a page can have 3 states: secure, normal or
shared. The hypervisor can call into a firmware function called
ultravisor that allows to change the state of a page: convert from/to
secure. The convert from secure will encrypt the page and make it
available to the host and host I/O. The convert to secure will remove
the host capability to access this page.
The design is that on convert to secure we will wait until writeback and
page refs are indicating no host usage. At the same time the convert
from secure (export to host) will be called in common code when the
refcount or the writeback bit is already set. This avoids races between
convert from and to secure.
Then there is also the concept of shared pages. Those are kind of secure
where the host can still access those pages. We need to be notified when
the guest "unshares" such a page, basically doing a convert to secure by
then. There is a call "pin shared page" that we use instead of convert
from secure when possible.
We do use PG_arch_1 as an optimization to minimize the convert from
secure/pin shared.
Several comments have been added in the code to explain the logic in
the relevant places.
Co-developed-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Before being able to host protected virtual machines, donate some of
the memory to the ultravisor. Besides that the ultravisor might impose
addressing limitations for memory used to back protected VM storage. Treat
that limit as protected virtualization host's virtual memory limit.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add "prot_virt" command line option which controls if the kernel
protected VMs support is enabled at early boot time. This has to be
done early, because it needs large amounts of memory and will disable
some features like STP time sync for the lpar.
Extend ultravisor info definitions and expose it via uv_info struct
filled in during startup.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
It turned out that fake numa support is rather useless on s390, since
there are no scenarios where there is any performance or other benefit
when used.
However it does provide maintenance cost and breaks from time to time.
Therefore remove it.
CONFIG_NUMA is still supported with a very small backend and only one
node. This way userspace applications which require NUMA interfaces
continue to work.
Note that NODES_SHIFT is set to 1 (= 2 nodes) instead of 0 (= 1 node),
since there is quite a bit of kernel code which assumes that more than
one node is possible if CONFIG_NUMA is enabled.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
sbale->addr holds an absolute address (or for some FCP usage, an opaque
request ID), and should only be used with proper virt/phys translation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
As the comment says, sl->sbal holds an absolute address. qeth currently
solves this through wild casting, while zfcp doesn't care.
Handle this properly in the code that actually builds the SL.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com> [for qdio]
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
s390 math emulation was removed with commit 5a79859ae0 ("s390:
remove 31 bit support"), rendering ieee_emulation_warnings useless.
The code still built because it was protected by CONFIG_MATHEMU, which
was no longer selectable.
This patch removes the sysctl_ieee_emulation_warnings declaration and
the sysctl entry declaration.
Link: https://lkml.kernel.org/r/20200214172628.3598516-1-steve@sk2.org
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Clang warns:
In file included from ../arch/s390/purgatory/purgatory.c:10:
In file included from ../include/linux/kexec.h:18:
In file included from ../include/linux/crash_core.h:6:
In file included from ../include/linux/elfcore.h:5:
In file included from ../include/linux/user.h:1:
In file included from ../arch/s390/include/asm/user.h:11:
../arch/s390/include/asm/page.h:45:6: warning: converting the result of
'<<' to a boolean always evaluates to false
[-Wtautological-constant-compare]
if (PAGE_DEFAULT_KEY)
^
../arch/s390/include/asm/page.h:23:44: note: expanded from macro
'PAGE_DEFAULT_KEY'
#define PAGE_DEFAULT_KEY (PAGE_DEFAULT_ACC << 4)
^
1 warning generated.
Explicitly compare this against zero to silence the warning as it is
intended to be used in a boolean context.
Fixes: de3fa841e4 ("s390/mm: fix compile for PAGE_DEFAULT_KEY != 0")
Link: https://github.com/ClangBuiltLinux/linux/issues/860
Link: https://lkml.kernel.org/r/20200214064207.10381-1-natechancellor@gmail.com
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Clang warns:
In file included from ../arch/s390/boot/startup.c:3:
In file included from ../include/linux/elf.h:5:
In file included from ../arch/s390/include/asm/elf.h:132:
In file included from ../include/linux/compat.h:10:
In file included from ../include/linux/time.h:74:
In file included from ../include/linux/time32.h:13:
In file included from ../include/linux/timex.h:65:
../arch/s390/include/asm/timex.h:160:20: warning: passing 'unsigned char
[16]' to parameter of type 'char *' converts between pointers to integer
types with different sign [-Wpointer-sign]
get_tod_clock_ext(clk);
^~~
../arch/s390/include/asm/timex.h:149:44: note: passing argument to
parameter 'clk' here
static inline void get_tod_clock_ext(char *clk)
^
Change clk's type to just be char so that it matches what happens in
get_tod_clock_ext.
Fixes: 57b28f6631 ("[S390] s390_hypfs: Add new attributes")
Link: https://github.com/ClangBuiltLinux/linux/issues/861
Link: http://lkml.kernel.org/r/20200208140858.47970-1-natechancellor@gmail.com
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
* fix register corruption
* ENOTSUPP/EOPNOTSUPP mixed
* reset cleanups/fixes
* selftests
x86:
* Bug fixes and cleanups
* AMD support for APIC virtualization even in combination with
in-kernel PIT or IOAPIC.
MIPS:
* Compilation fix.
Generic:
* Fix refcount overflow for zero page.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeOuf7AAoJEL/70l94x66DOBQH/j1W9lUpbDgr9aWbrZT+O/yP
FWzUDrRlCZCjV1FQKbGPa4YLeDRTG5n+RIQTjmCGRqiMqeoELSJ1+iK99e97nG/u
L28zf/90Nf0R+wwHL4AOFeploTYfG4WP8EVnlr3CG2UCJrNjxN1KU7yRZoWmWa2d
ckLJ8ouwNvx6VZd233LVmT38EP4352d1LyqIL8/+oXDIyAcRJLFQu1gRCwagsh3w
1v1czowFpWnRQ/z9zU7YD+PA4v85/Ge8sVVHlpi1X5NgV/khk4U6B0crAw6M+la+
mTmpz9g56oAh9m9NUdtv4zDCz1EWGH0v8+ZkAajUKtrM0ftJMn57P6p8PH4VVlE=
=5+Wl
-----END PGP SIGNATURE-----
Merge tag 'kvm-5.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
"s390:
- fix register corruption
- ENOTSUPP/EOPNOTSUPP mixed
- reset cleanups/fixes
- selftests
x86:
- Bug fixes and cleanups
- AMD support for APIC virtualization even in combination with
in-kernel PIT or IOAPIC.
MIPS:
- Compilation fix.
Generic:
- Fix refcount overflow for zero page"
* tag 'kvm-5.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (42 commits)
KVM: vmx: delete meaningless vmx_decache_cr0_guest_bits() declaration
KVM: x86: Mark CR4.UMIP as reserved based on associated CPUID bit
x86: vmxfeatures: rename features for consistency with KVM and manual
KVM: SVM: relax conditions for allowing MSR_IA32_SPEC_CTRL accesses
KVM: x86: Fix perfctr WRMSR for running counters
x86/kvm/hyper-v: don't allow to turn on unsupported VMX controls for nested guests
x86/kvm/hyper-v: move VMX controls sanitization out of nested_enable_evmcs()
kvm: mmu: Separate generating and setting mmio ptes
kvm: mmu: Replace unsigned with unsigned int for PTE access
KVM: nVMX: Remove stale comment from nested_vmx_load_cr3()
KVM: MIPS: Fold comparecount_func() into comparecount_wakeup()
KVM: MIPS: Fix a build error due to referencing not-yet-defined function
x86/kvm: do not setup pv tlb flush when not paravirtualized
KVM: fix overflow of zero page refcount with ksm running
KVM: x86: Take a u64 when checking for a valid dr7 value
KVM: x86: use raw clock values consistently
KVM: x86: reorganize pvclock_gtod_data members
KVM: nVMX: delete meaningless nested_vmx_run() declaration
KVM: SVM: allow AVIC without split irqchip
kvm: ioapic: Lazy update IOAPIC EOI
...
- Add KPROBES_ON_FTRACE support.
- Add EP11 AES secure keys support.
- PAES rework and prerequisites for paes-s390 ciphers selftests.
- Fix page table upgrade for hugetlbfs.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl465KkACgkQjYWKoQLX
FBiR/wf/e+Fj/mDYHElcZ55MWaORBpp8NT94IYSt0RbII1PEh9cB8NciYLQdFFmc
bUlNj7u3fHwk1D8S3pOSYKhIaHQQOWDqd/uNTzbCicbbVhuwmslLc+jffnORtlKe
mCHeQsVAw3NwE8FIPhPMTAKBZV0pLkM4T9PA2xgeuB5cShoMgXgLgUoIwHJ4c2TP
WwnolIJ/QR0nKpmPI5lp0+PjjSk/8nA/VvmpxgYbJCTQm8dhwhAfePh8Kf6pEp6K
wETUaIyWkX1a+kI9h2qIBsR7KplqqrKABA5sxnPDQW/kut1Pc/2fWxMOBxux0f/V
Kk+f6yoVbe7X6VYm+V4AyyAzQMRggQ==
=9Eeg
-----END PGP SIGNATURE-----
Merge tag 's390-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
"The second round of s390 fixes and features for 5.6:
- Add KPROBES_ON_FTRACE support
- Add EP11 AES secure keys support
- PAES rework and prerequisites for paes-s390 ciphers selftests
- Fix page table upgrade for hugetlbfs"
* tag 's390-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pkey/zcrypt: Support EP11 AES secure keys
s390/zcrypt: extend EP11 card and queue sysfs attributes
s390/zcrypt: add new low level ep11 functions support file
s390/zcrypt: ep11 structs rework, export zcrypt_send_ep11_cprb
s390/zcrypt: enable card/domain autoselect on ep11 cprbs
s390/crypto: enable clear key values for paes ciphers
s390/pkey: Add support for key blob with clear key value
s390/crypto: Rework on paes implementation
s390: support KPROBES_ON_FTRACE
s390/mm: fix dynamic pagetable upgrade for hugetlbfs
- Enable CMA
- Add support for MB v11
- Defconfig updates
- Minor fixes
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXjlJ1gAKCRDKSWXLKUoM
IWy9AJ4tauV9sUb+zNadrYxI+2zemRstUwCfQ49LG4kHpFCv8ldSTmhBPJY/3MI=
=QpT4
-----END PGP SIGNATURE-----
Merge tag 'microblaze-v5.6-rc1' of git://git.monstr.eu/linux-2.6-microblaze
Pull Microblaze update from Michal Simek:
- enable CMA
- add support for MB v11
- defconfig updates
- minor fixes
* tag 'microblaze-v5.6-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Add ID for Microblaze v11
microblaze: Prevent the overflow of the start
microblaze: Wire CMA allocator
asm-generic: Make dma-contiguous.h a mandatory include/asm header
microblaze: Sync defconfig with latest Kconfig layout
microblaze: defconfig: Disable EXT2 driver and Enable EXT3 & EXT4 drivers
microblaze: Align comments with register usage
dma-continuguous.h is generic for all architectures except arm32 which has
its own version.
Similar change was done for msi.h by commit a1b39bae16
("asm-generic: Make msi.h a mandatory include/asm header")
Suggested-by: Christoph Hellwig <hch@infradead.org>
Link: https://lore.kernel.org/linux-arm-kernel/20200117080446.GA8980@lst.de/T/#m92bb56b04161057635d4142e1b3b9b6b0a70122e
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Paul Walmsley <paul.walmsley@sifive.com> # for arch/riscv
walk_page_range() is going to be allowed to walk page tables other than
those of user space. For this it needs to know when it has reached a
'leaf' entry in the page tables. This information is provided by the
p?d_leaf() functions/macros.
For s390, pud_large() and pmd_large() are already implemented as static
inline functions. Add a macro to provide the p?d_leaf names for the
generic code to use.
Link: http://lkml.kernel.org/r/20191218162402.45610-9-steven.price@arm.com
Signed-off-by: Steven Price <steven.price@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: "Liang, Kan" <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Zong Li <zong.li@sifive.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CRNG hasn't initialized, instead of the old blocking pool. Also clean
up archrandom.h, and some other miscellaneous cleanups.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAl40j1kACgkQ8vlZVpUN
gaPCywf8CWS9HFd2Iipj60gkTVugjlL5ib0lbfhQcAAwwzw1GLTXJSMBzzoMRHY/
ZI2sJZS1m0V1oWNnXXVKi+A1VXmlValWXAc+7fvbeaIe5pRT1EHP14s4Kz7/4d8Q
dk0b8cxNpR8u5CcbN8y9D+71IKpdksUbX7uGuGfw3bncQdRNwJVf+oS1fMGS0Rsb
F8ddQaED7iFpX2BMl56afQ4t2t0LA5+eLYMGoYoJx5fgd9BseP0TEcjj9Y4Z30M7
+GO4NZjUbAY0syx9r8hx3P/5miWZm2J9QJmJoXHhr5+IcAKM+6+Uo6X6gkOEqV4i
U//V1cqNuowV5ckE4Na+MfBillinsQ==
=HeFM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random changes from Ted Ts'o:
"Change /dev/random so that it uses the CRNG and only blocking if the
CRNG hasn't initialized, instead of the old blocking pool. Also clean
up archrandom.h, and some other miscellaneous cleanups"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (24 commits)
s390x: Mark archrandom.h functions __must_check
powerpc: Mark archrandom.h functions __must_check
powerpc: Use bool in archrandom.h
x86: Mark archrandom.h functions __must_check
linux/random.h: Mark CONFIG_ARCH_RANDOM functions __must_check
linux/random.h: Use false with bool
linux/random.h: Remove arch_has_random, arch_has_random_seed
s390: Remove arch_has_random, arch_has_random_seed
powerpc: Remove arch_has_random, arch_has_random_seed
x86: Remove arch_has_random, arch_has_random_seed
random: remove some dead code of poolinfo
random: fix typo in add_timer_randomness()
random: Add and use pr_fmt()
random: convert to ENTROPY_BITS for better code readability
random: remove unnecessary unlikely()
random: remove kernel.random.read_wakeup_threshold
random: delete code to pull data into pools
random: remove the blocking pool
random: make /dev/random be almost like /dev/urandom
random: ignore GRND_RANDOM in getentropy(2)
...
Pull updates from Andrew Morton:
"Most of -mm and quite a number of other subsystems: hotfixes, scripts,
ocfs2, misc, lib, binfmt, init, reiserfs, exec, dma-mapping, kcov.
MM is fairly quiet this time. Holidays, I assume"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
kcov: ignore fault-inject and stacktrace
include/linux/io-mapping.h-mapping: use PHYS_PFN() macro in io_mapping_map_atomic_wc()
execve: warn if process starts with executable stack
reiserfs: prevent NULL pointer dereference in reiserfs_insert_item()
init/main.c: fix misleading "This architecture does not have kernel memory protection" message
init/main.c: fix quoted value handling in unknown_bootoption
init/main.c: remove unnecessary repair_env_string in do_initcall_level
init/main.c: log arguments and environment passed to init
fs/binfmt_elf.c: coredump: allow process with empty address space to coredump
fs/binfmt_elf.c: coredump: delete duplicated overflow check
fs/binfmt_elf.c: coredump: allocate core ELF header on stack
fs/binfmt_elf.c: make BAD_ADDR() unlikely
fs/binfmt_elf.c: better codegen around current->mm
fs/binfmt_elf.c: don't copy ELF header around
fs/binfmt_elf.c: fix ->start_code calculation
fs/binfmt_elf.c: smaller code generation around auxv vector fill
lib/find_bit.c: uninline helper _find_next_bit()
lib/find_bit.c: join _find_next_bit{_le}
uapi: rename ext2_swab() to swab() and share globally in swab.h
lib/scatterlist.c: adjust indentation in __sg_alloc_table
...
Add the new kernel command line parameter 'dfltcc=' to configure s390
zlib hardware support.
Format: { on | off | def_only | inf_only | always }
on: s390 zlib hardware support for compression on
level 1 and decompression (default)
off: No s390 zlib hardware support
def_only: s390 zlib hardware support for deflate
only (compression on level 1)
inf_only: s390 zlib hardware support for inflate
only (decompression)
always: Same as 'on' but ignores the selected compression
level always using hardware support (used for debugging)
Link: http://lkml.kernel.org/r/20200103223334.20669-5-zaslonko@linux.ibm.com
Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Cc: Chris Mason <clm@fb.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Sterba <dsterba@suse.com>
Cc: Eduard Shishkin <edward6@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ilya Leoshkevich <iii@linux.ibm.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PPC: Bugfixes
x86:
* Support for mapping DAX areas with large nested page table entries.
* Cleanups and bugfixes here too. A particularly important one is
a fix for FPU load when the thread has TIF_NEED_FPU_LOAD. There is
also a race condition which could be used in guest userspace to exploit
the guest kernel, for which the embargo expired today.
* Fast path for IPI delivery vmexits, shaving about 200 clock cycles
from IPI latency.
* Protect against "Spectre-v1/L1TF" (bring data in the cache via
speculative out of bound accesses, use L1TF on the sibling hyperthread
to read it), which unfortunately is an even bigger whack-a-mole game
than SpectreV1.
Sean continues his mission to rewrite KVM. In addition to a sizable
number of x86 patches, this time he contributed a pretty large refactoring
of vCPU creation that affects all architectures but should not have any
visible effect.
s390 will come next week together with some more x86 patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeMxtCAAoJEL/70l94x66DQxIIAJv9hMmXLQHGFnUMskjGErR6
DCLSC0YRdRMwE50CerblyJtGsMwGsPyHZwvZxoAceKJ9w0Yay9cyaoJ87ItBgHoY
ce0HrqIUYqRSJ/F8WH2lSzkzMBr839rcmqw8p1tt4D5DIsYnxHGWwRaaP+5M/1KQ
YKFu3Hea4L00U339iIuDkuA+xgz92LIbsn38svv5fxHhPAyWza0rDEYHNgzMKuoF
IakLf5+RrBFAh6ZuhYWQQ44uxjb+uQa9pVmcqYzzTd5t1g4PV5uXtlJKesHoAvik
Eba8IEUJn+HgQJjhp3YxQYuLeWOwRF3bwOiZ578MlJ4OPfYXMtbdlqCQANHOcGk=
=H/q1
-----END PGP SIGNATURE-----
Merge tag 'kvm-5.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"This is the first batch of KVM changes.
ARM:
- cleanups and corner case fixes.
PPC:
- Bugfixes
x86:
- Support for mapping DAX areas with large nested page table entries.
- Cleanups and bugfixes here too. A particularly important one is a
fix for FPU load when the thread has TIF_NEED_FPU_LOAD. There is
also a race condition which could be used in guest userspace to
exploit the guest kernel, for which the embargo expired today.
- Fast path for IPI delivery vmexits, shaving about 200 clock cycles
from IPI latency.
- Protect against "Spectre-v1/L1TF" (bring data in the cache via
speculative out of bound accesses, use L1TF on the sibling
hyperthread to read it), which unfortunately is an even bigger
whack-a-mole game than SpectreV1.
Sean continues his mission to rewrite KVM. In addition to a sizable
number of x86 patches, this time he contributed a pretty large
refactoring of vCPU creation that affects all architectures but should
not have any visible effect.
s390 will come next week together with some more x86 patches"
* tag 'kvm-5.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
x86/KVM: Clean up host's steal time structure
x86/KVM: Make sure KVM_VCPU_FLUSH_TLB flag is not missed
x86/kvm: Cache gfn to pfn translation
x86/kvm: Introduce kvm_(un)map_gfn()
x86/kvm: Be careful not to clear KVM_VCPU_FLUSH_TLB bit
KVM: PPC: Book3S PR: Fix -Werror=return-type build failure
KVM: PPC: Book3S HV: Release lock on page-out failure path
KVM: arm64: Treat emulated TVAL TimerValue as a signed 32-bit integer
KVM: arm64: pmu: Only handle supported event counters
KVM: arm64: pmu: Fix chained SW_INCR counters
KVM: arm64: pmu: Don't mark a counter as chained if the odd one is disabled
KVM: arm64: pmu: Don't increment SW_INCR if PMCR.E is unset
KVM: x86: Use a typedef for fastop functions
KVM: X86: Add 'else' to unify fastop and execute call path
KVM: x86: inline memslot_valid_for_gpte
KVM: x86/mmu: Use huge pages for DAX-backed files
KVM: x86/mmu: Remove lpage_is_disallowed() check from set_spte()
KVM: x86/mmu: Fold max_mapping_level() into kvm_mmu_hugepage_adjust()
KVM: x86/mmu: Zap any compound page when collapsing sptes
KVM: x86/mmu: Remove obsolete gfn restoration in FNAME(fetch)
...
