In status register, fifo_count is bit[29:17].
(0x1FFF is correct)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Turning the cache off implies flushing cache which doesn't define
maximum timeout unlike cache-on. This patch will apply the generic
CMD6 timeout only for cache-on. Additionally the kernel message is
added for checking failure case of cache-on.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
With the inclusion of following patch (59b5bc3929b37):
"mmc: sdhci: remove "state" argument from sdhci_suspend_host"
we get a compilation error for sdhci-spear:
drivers/mmc/host/sdhci-spear.c:283:2: error: too many arguments to function
‘sdhci_suspend_host’
This patch fixes this error.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If there are errors happened in sdhci_suspend_host, handle it so that
when the function returns with an error, the host's behaviour is the
same before this function call, e.g. card detection is enabled and
tuning timer is active, etc.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
UHS_REG should be cleared for non-DDR mode. But currently there is
no way to clear DDR mode, if it is already set once. This patch adds
clearing DDR mode for non-DDR mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a failure to recognize SD cards reported on a Dell
Vostro with O2 Micro SD card reader. Patch 49c468f ("mmc: sd: add
support for uhs bus speed mode selection") caused the problem, by
setting the SDHCI_CTRL_HISPD flag even for legacy timings.
Signed-off-by: Alexander Elbs <alex@segv.de>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When suspending host, the tuning timer shoule be deactivated.
And the HOST_NEEDS_TUNING flag should be set after tuning timer is
deactivated.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host may now use MMC_CAP2_NO_SLEEP_CMD to disable the use
of eMMC sleep/awake command.
This option can be used when your platform has a buggy
kernel crash dump software, which is supposed to store
the dump on the eMMC, but is not able to wake up the eMMC
from sleep state.
In particular, failures have been seen with u-boot; even if
it is fixed there, platforms will be slow to update their
bootloader binaries.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As the card-detect irq handler just schedules work to be done by a
thread, we can use request_threaded_irq to do much of the work for
us. This means that interrupts which arrive by handle_nested_irq
actually work.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Kishore Kadiyala <kishorek.kadiyala@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Runtime PM for SDIO is no longer enabled by default (see
5c7f0e083d) so it must now
be enabled per platform, in this case Medfield uses it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
To allow the set_clock host op to disable the SDCLK source when not
needed, always call the host op when the requested clock speed is
zero. Do this even if host->clock already equals zero, because
the SDHCI driver may set that value (without calling the host op)
to force an update at the next (non-zero-speed) call.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Even if a driver provides separate card detection, an interrupt
is still needed to abort mmc requests that are in progress.
SDHCI_QUIRK2_OWN_CARD_DETECTION prevents that, so remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Retrieve the GPIO numbers for hardware reset and
card detect from platform data.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a means of getting platform data for the SDHCI PCI
devices. The data is stored against the slot not the
device in order to support multi-slot devices.
The data allows platform-specific setup (such as getting
GPIO numbers from firmware or setting up wl12xx for SDIO)
to be done in platform support files instead of the
sdhci-pci driver.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not enable card detection interrupts for non-removable cards.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Presently the vmmc regulator is enabled when the host
controller is added and disabled when it is removed.
However, the vmmc regulator should be under the control
of the upper layers via ->set_ios(). Make it so.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
While calling mmc_cache_ctrl() a host is not claimed. This patch
adds the mmc_try_claim_host() for quick response in suspend.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC master clock rate can vary for each instance of the MMC controller
on the device. Use clk_get_rate instead to get the value.
Signed-off-by: Balaji TK <balajitk@ti.com>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch converts the sh_mmcif MMC host driver to process requests
asynchronously instead of waiting in its .request() method for completion.
This is achieved by using threaded IRQs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch doesn't introduce any functional changes, it only simplifies
some code fragments, removes superfluous parameters, fixes typos.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
If an interrupt is coming with both error and data completion status bits
set, it has to be handled as an error interrupt, for which error interrupts
have to be processed first. The current version of the driver on the
contrary doesn't recognise such interrupts as an error event, which leads
to data corruption and breaks the error recovery.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds a primitive helper to support card hotplug detection on
platforms, where a GPIO, capable of producing interrupts, is used for
detection of card-insertion and -removal events.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch regroups the code slightly, adds documentation and allows
the rtpm counter of MMC_CAP_NEEDS_POLL devices to reach 0 again.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
[g.liakhovetski@gmx.de: restore pm_runtime_get_noresume()]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes the wrong comparison before setting the interface
voltage in DDR mode.
The assignment to the variable ddr before comaprison is either
ddr = MMC_1_2V_DDR_MODE; or ddr == MMC_1_8V_DDR_MODE. But the comparison
is done with the extended csd value if ddr == EXT_CSD_CARD_TYPE_DDR_1_2V.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Philip Rakity <prakity@marvell.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the support for predefined multiple block r/w.
dw_mmc can support MMC_CAP_CMD23 capability.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds another capabilities field for MMC_CAPS2_XXX.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch modifies dw_mmc to use dev_pm_ops.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Kill block requests when the host realizes that the card is
removed from the slot and is sure that subsequent requests
are bound to fail. Do this silently so that the block
layer doesn't output unnecessary error messages.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
c31b50e (mmc: core: Use delayed work in clock gating framework,
2011-11-14) missed a few things during review:
o A useless pr_info()
o milliseconds was written as two words
o The sysfs file had units in its output
Fix all three problems.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable boot partitions to be read-only locked until next power on via
a sysfs entry. There will be one sysfs entry for each boot partition:
/sys/block/mmcblkXbootY/ro_lock_until_next_power_on
Each boot partition is locked by writing 1 to its file.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: John Beckett <john.beckett@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci-s3c updates pm_caps from platform data for SDIO PM.
Signed-off-by: Sangwook Lee <sangwook.lee@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a function mmc_detect_card_removed() which upper layers can use to
determine immediately if a card has been removed. This function should
be called after an I/O request fails so that all queued I/O requests
can be errored out immediately instead of waiting for the card device
to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch converts the drivers in drivers/mmc/host/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Replace ilog2(__rounddown_pow_of_two(x)) with the equivalent but much
simpler fls(x) - 1.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the read or write buffer size associated with the command sent
through the mmc_blk_ioctl is zero, do not prepare data buffer.
This enables a ioctl(2) call to for instance send a MMC_SWITCH to set
a byte in the ext_csd.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
1ms is enough for hardware to change the clock to stable.
100ms is too long in the tasklet.
Signed-off-by: Tony Lin <tony.lin@freescale.com>
CC: Xiaobo Xie <X.Xie@freescale.com>
CC: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If max_seg_size is unaligned, mmc_test_map_sg() may create sg element
sizes that are not aligned with 512 byte. Fix, align max_seg_size at
mmc_test_area_init().
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for sdio UHS cards per the version 3.0
spec.
UHS mode is only enabled for version 3.0 cards when both the
host and the controller support UHS modes.
1.8v signaling support is removed if both the card and the
host do not support UHS. This is done to maintain
compatibility and some system/card combinations break when
1.8v signaling is enabled when the host does not support UHS.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Aaron Lu <Aaron.lu@amd.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend/Resume is missing from sdhci-spear driver. This patch adds
support for suspend/resume for this driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current clock gating framework disables the MCI clock as soon as the
request is completed and enables it when a request arrives. This aggressive
clock gating framework, when enabled, cause following issues:
When there are back-to-back requests from the Queue layer, we unnecessarily
end up disabling and enabling the clocks between these requests since 8MCLK
clock cycles is a very short duration compared to the time delay between
back to back requests reaching the MMC layer. This overhead can effect the
overall performance depending on how long the clock enable and disable
calls take which is platform dependent. For example on some platforms we
can have clock control not on the local processor, but on a different
subsystem and the time taken to perform the clock enable/disable can add
significant overhead.
Also if the host controller driver decides to disable the host clock too
when mmc_set_ios function is called with ios.clock=0, it adds additional
delay and it is highly possible that the next request had already arrived
and unnecessarily blocked in enabling the clocks. This is seen frequently
when the processor is executing at high speeds and in multi-core platforms
thus reduces the overall throughput compared to if clock gating is
disabled.
Fix this by delaying turning off the clocks by posting request on
delayed workqueue. Also cancel the unscheduled pending work, if any,
when there is access to card.
sysfs entry is provided to tune the delay as needed, default
value set to 200ms.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
No functional change; adds macros for card manufacturer IDs.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Andrei E. Warkentin <andrey.warkentin@gmail.com>
Cc: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
This patch is to expose the actual SDCLK frequency in
/sys/kernel/debug/mmcX/ios entry.
For example, if the max clk for a normal speed card is 20MHz this
is reported in /sys/kernel/debug/mmcX/ios. Unfortunately the actual
SDCLK frequency (i.e. Baseclock / divisor) is not reported at all:
for example, in that case, on Arasan HC, it should be 48/4=12 (MHz).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch allows any block size to be set on the SDIO link,
and still have an arbitrary sized packet (adjusted in size by
using sdio_align_size) transferred in an optimal way
(preferably one transfer).
Previously if the block size was larger than the default of
512 bytes and the transfer size was exactly one block size
(possibly thanks to using sdio_align_size to get an optimal
transfer size), it was sent as a number of byte transfers instead
of one block transfer. Also if the number of blocks was
(max_blocks * N) + 1, the tranfer would be conducted with a number
of blocks and finished off with a number of byte transfers.
When doing this change it was also possible to break out the quirk
for broken byte mode in a much cleaner way, and collect the logic of
when to do byte or block transfer in one function instead of two.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
