Report the DT output port number in dw_hdmi_plat_data to connect to the
next bridge in the dw-hdmi driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Replace the manual panel handling with usage of the DRM panel bridge
helper. This simplifies the driver, and brings support for
DRM_BRIDGE_ATTACH_NO_CONNECTOR as an added bonus.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
On all platforms except i.MX and Rockchip, the dw-hdmi DT bindings
require a video output port connected to an HDMI sink (most likely an
HDMI connector, in rare cases another bridges converting HDMI to another
protocol). For those platforms, retrieve the next bridge and attach it
from the dw-hdmi bridge attach handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Being informed of a failure to attach a bridge is useful, and many
drivers prints an error message in that case. Move the message to
drm_bridge_attach() to avoid code duplication.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
When the device is unbound from the driver (the DU being a platform
device, this occurs either when removing the DU module, or when
unbinding the device manually through sysfs), the display may be active.
Make sure it gets shut down.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The reference to the drm_device that was acquired by
devm_drm_dev_alloc() is released automatically by the devres
infrastructure. It must not be released manually, as that causes a
reference underflow..
Fixes: ea6aae1518 ("drm: rcar-du: Embed drm_device in rcar_du_device")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
When the system shuts down or warm reboots, the display may be active,
with the hardware accessing system memory. Upon reboot, the DDR will not
be accessible, which may cause issues.
Implement the platform_driver .shutdown() operation and shut down the
display to fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Don't populate the const array frs_limits on the stack but instead make
it static. Makes the object code smaller by 128 bytes:
Before:
text data bss dec hex filename
24845 7440 64 32349 7e5d ./drivers/gpu/drm/bridge/tc358768.o
After:
text data bss dec hex filename
24749 7408 64 32221 7ddd ./drivers/gpu/drm/bridge/tc358768.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
In the next patch, we start having more than a single potential failure
reason.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-9-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Previously the (non-fd) fence returned from submit ioctl was a raw
seqno, which is scoped to the ring. But from UABI standpoint, the
ioctls related to seqno fences all specify a submitqueue. We can
take advantage of that to replace the seqno fences with a cyclic idr
handle.
This is in preperation for moving to drm scheduler, at which point
the submit ioctl will return after queuing the submit job to the
scheduler, but before the submit is written into the ring (and
therefore before a ring seqno has been assigned). Which means we
need to replace the dma_fence that userspace may need to wait on
with a scheduler fence.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-8-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move all the locked/active/pinned state handling to msm_gem_submit.c.
In particular, for drm/scheduler, we'll need to do all this before
pushing the submit job to the scheduler. But while we're at it we can
get rid of the dupicate pin and refcnt.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-7-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that no one is using it, remove it.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://lore.kernel.org/r/20210728010632.2633470-5-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
No idea why we were still using this. It certainly hasn't been needed
for some time. So drop the pointless twin codepaths.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-4-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
If we don't have a gpu, there is no need to create a submitqueue, which
lets us simplify the error handling and submitqueue creation.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fix a couple incorrect or misspelt comments, and add submitqueue doc
comment.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
This adds a few things to try and make frequency scaling better match
the workload:
1) Longer polling interval to avoid whip-lashing between too-high and
too-low frequencies in certain workloads, like mobile games which
throttle themselves to 30fps.
Previously our polling interval was short enough to let things
ramp down to minimum freq in the "off" frame, but long enough to
not react quickly enough when rendering started on the next frame,
leading to uneven frame times. (Ie. rather than a consistent 33ms
it would alternate between 16/33/48ms.)
2) Awareness of when the GPU is active vs idle. Since we know when
the GPU is active vs idle, we can clamp the frequency down to the
minimum while it is idle. (If it is idle for long enough, then
the autosuspend delay will eventually kick in and power down the
GPU.)
Since devfreq has no knowledge of powered-but-idle, this takes a
small bit of trickery to maintain a "fake" frequency while idle.
This, combined with the longer polling period allows devfreq to
arrive at a reasonable "active" frequency, while still clamping
to minimum freq when idle to reduce power draw.
3) Boost. Because simple_ondemand needs to see a certain threshold
of busyness to ramp up, we could end up needing multiple polling
cycles before it reacts appropriately on interactive workloads
(ex. scrolling a web page after reading for some time), on top
of the already lengthened polling interval, when we see a idle
to active transition after a period of idle time we boost the
frequency that we return to.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210726144653.2180096-4-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
In the next patch, it grows a bit more, so lets not duplicate the logic
in multiple places.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210726144653.2180096-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Before we start adding more cleverness, split it into it's own file.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210726144653.2180096-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Nothing we do to in update_fences() can't be done in an atomic context,
so move this into the GPU's irq context to reduce latency (and call
dma_fence_signal() so we aren't relying on dma_fence_is_signaled() which
would defeat the purpose).
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210726144359.2179302-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Let dma_fence::signaled, etc, read directly from the address that the hw
is writing with updated completed fence seqno, so we can potentially
notice that the fence is signaled sooner.
Plus add some docs.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210726144359.2179302-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Commit 2f015ec6ea ("drm/dp_mst: Add sideband down request tracing +
selftests") added some debug code for sideband message tracing. But
it seems to have unintentionally changed the behavior on sideband message
failure. It catches and returns failure only if DRM_UT_DP is enabled.
Otherwise it ignores the error code and returns success. So on an MST
unplug, the caller is unaware that the clear payload message failed and
ends up waiting for 4 seconds for the response. Fixes the issue by
returning the proper error code.
Changes in V2:
-- Revise commit text as review comment
-- add Fixes text
Changes in V3:
-- remove "unlikely" optimization
Fixes: 2f015ec6ea ("drm/dp_mst: Add sideband down request tracing + selftests")
Cc: <stable@vger.kernel.org> # v5.5+
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1625585434-9562-1-git-send-email-khsieh@codeaurora.org
Make sure the FIFO_CLEAR bit is latched in when configuring the
controller, so that the FIFO is really cleared. And then clear
the FIFO_CLEAR bit, since it is not self-clearing.
Fixes: 45d59d7040 ("drm: Add new driver for MXSFB controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # i.Core MX8MM
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210620224946.189524-1-marex@denx.de
In case there is a bridge connected to the LCDIF, use bus_format
from the bridge, otherwise behave as before and use bus_format
from the connector. This way, even if there are multiple bridges
in the display pipeline, the LCDIF will use the correct format.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210726194457.341696-1-marex@denx.de
In case the DRAM is under high load, the MXSFB FIFO might underflow
and that causes visible artifacts. This could be triggered on i.MX8MM
using e.g. "$ memtester 128M" on a device with 1920x1080 panel. The
first "Stuck Address" test of the memtester will completely corrupt
the image on the panel and leave the MXSFB FIFO in odd state.
To avoid this underflow, increase number of outstanding requests to
DRAM from 2 to 16, which is the maximum. This mitigates the issue
and it can no longer be triggered.
Fixes: 45d59d7040 ("drm: Add new driver for MXSFB controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210620224759.189351-1-marex@denx.de
There is some sort of corner case behavior of the controller,
which could rarely be triggered at least on i.MX6SX connected
to 800x480 DPI panel and i.MX8MM connected to DPI->DSI->LVDS
bridged 1920x1080 panel (and likely on other setups too), where
the image on the panel shifts to the right and wraps around.
This happens either when the controller is enabled on boot or
even later during run time. The condition does not correct
itself automatically, i.e. the display image remains shifted.
It seems this problem is known and is due to sporadic underflows
of the LCDIF FIFO. While the LCDIF IP does have underflow/overflow
IRQs, neither of the IRQs trigger and neither IRQ status bit is
asserted when this condition occurs.
All known revisions of the LCDIF IP have CTRL1 RECOVER_ON_UNDERFLOW
bit, which is described in the reference manual since i.MX23 as
"
Set this bit to enable the LCDIF block to recover in the next
field/frame if there was an underflow in the current field/frame.
"
Enable this bit to mitigate the sporadic underflows.
Fixes: 45d59d7040 ("drm: Add new driver for MXSFB controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210620224701.189289-1-marex@denx.de
[Why]
GPINT commands have the lowest priority in DMCUB, so it's possible
that the command isn't processed in time.
[How]
Add a log to help identify this case.
Reviewed-by: Koo Anthony <Anthony.Koo@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Would like to identify the cause of AUX transactions failing
via ETW logs.
[How]
Add ETW logging for AUX failures.
Reviewed-by: Pavic Josip <Josip.Pavic@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
For dual eDP when setting the new settings we need to set
command version to DMUB_CMD_PSR_CONTROL_VERSION_1, otherwise
DMUB will not read panel_inst parameter.
[how]
Instead of PSR_VERSION_1 pass DMUB_CMD_PSR_CONTROL_VERSION_1
Reviewed-by: Wood Wyatt <Wyatt.Wood@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
IP parameter min_meta_chunk_size_bytes is read for bandwidth
calculations but it was never defined.
[how]
Define min_meta_chunk_size_bytes and initialize value to 256.
Reviewed-by: Laktyushkin Dmytro <dmytro.laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rename amdgpu_acpi_is_s0ix_supported to better explain
functionality by renaming to amdgpu_acpi_is_s0ix_active
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DST_Y_PREFETCH can overflow when DestinationLinesForPrefetch values are
too large due to the former being limited to 8 bits.
[how]
Set the maximum value of DestinationLinesForPrefetch to be 255 * refclk
period.
Reviewed-by: Laktyushkin Dmytro <dmytro.laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
User might change the suspend behaviour from OS.
[How]
Check with pm for target suspend state and set s0ix
flag only for s2idle state.
v2: User might change default suspend state, use target state
v3: squash in build fix
Suggested-by: Lijo Lazar <Lijo.Lazar@amd.com>
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We already have logging for ADDFB2. Add some logging for RMFB as
well.
This can be handy when trying to find out why a CRTC gets magically
disabled.
v2: make log message more explicit, add log messages to
drm_framebuffer_remove (Daniel)
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/EghsoRDcn1SJV0nxVqRCisPd7v0627yLZbBjn4A8Yg@cp3-web-048.plabs.ch
Required bump from v5.13-rc3 to v5.14-rc3, and to pick up sysfb compilation fixes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We're trying to have a fairly strict split between core functionality
that defines the uapi, including the docs, and the helper functions to
implement it.
Move drm_plane_enable_fb_damage_clips and associated kerneldoc into
drm_plane from drm_damage_helper.c to fix this.
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723083457.696939-3-daniel.vetter@ffwll.ch
There's two stages of manual upload/invalidate displays:
- just handling dirtyfb and uploading the entire fb all the time
- looking at damage clips
In the latter case we support it through fbdev emulation (with
fb_defio), atomic property, and with the dirtfy clip rects.
Make sure at least the atomic property is set up as the main official
interface for this. Ideally we'd also check that
drm_atomic_helper_dirtyfb() is used and that fbdev defio is set up,
but that's quite a bit harder to do. Ideas very much welcome.
From a cursor audit drivers seem to be getting this right mostly, but
better to make sure. At least no one is bypassing the accessor
function.
v2:
- use drm_warn_once with a meaningful warning string (José)
- don't splat in the atomic check code for everyone (intel-gfx-ci)
Reviewed-by: José Roberto de Souza <jose.souza@intel.com> (v1)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723083457.696939-2-daniel.vetter@ffwll.ch
It's not used. Drivers should instead use the helpers anyway.
Currently both vbox and i915 hand-roll this and it's not the greatest.
vbox looks buggy, and i915 does a bit much that helpers would take
care of I think.
Also improve the kerneldocs while we're at it.
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723083457.696939-1-daniel.vetter@ffwll.ch
Finding panel_or_bridge might vary based on associated
DSI devices like DSI panel, bridge, and I2C based DSI
bridge.
1. DSI panels and bridges will invoke the host attach
from probe in order to find the panel_or_bridge.
chipone_probe()
dw_mipi_dsi_host_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_host_attach().start
chipone_attach(). start
chipone_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
2. I2C based DSI bridge will invoke the drm_bridge_attach
from bridge attach in order to find the panel_or_bridge.
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
dw_mipi_dsi_host_attach().start
sn65dsi83_attach(). start
sn65dsi83_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
So, invoke the panel_or_bridge from host attach and
bridge attach in order to find all possible DSI devices.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210704140309.268469-1-jagan@amarulasolutions.com
Many of the DSI flags have names opposite to their actual effects,
e.g. MIPI_DSI_MODE_EOT_PACKET means that EoT packets will actually
be disabled. Fix this by including _NO_ in the flag names, e.g.
MIPI_DSI_MODE_NO_EOT_PACKET.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@samsung.com>
Reviewed-by: Xin Ji <xji@analogixsemi.com> # anx7625.c
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> # msm/dsi
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727094435.v3.1.I629b2366a6591410359c7fcf6d385b474b705ca2@changeid
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmD95yIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGqp0H/j/xHL20EHaUJOaV
iJjnfGyjtnkLC5FCoV/q/v9sFuSW2p4W1nyF8/eIgVKObef94Mg4/xxaHQrWIM56
cbzK9aIcD9InAuImJ6lju4fqjNmFrt2x7mhfzjPKqmhfINfZ5CohpLFN5XdOwzYC
l+ZgmUUl7GLDAND2M6rtkc7AOk4qTyAySDvvPFELE/uNgV4EKaENSIWofHhEzW5v
Yk+4agawaFTfa6H9+uMVYZBOcEKwheQ0E2tcOJvHJT8Mwm8MFoC/B7fLY5zxIdN2
7A7r/7qbSQmSDSjOgwKS4ZOjom0xGSD+V+596SzET6jkbahR2HJ/mrFvmD7GNEoW
OWJPjzI=
=vzIM
-----END PGP SIGNATURE-----
Backmerge tag 'v5.14-rc3' into drm-next
Linux 5.14-rc3
Daniel said we should pull the nouveau fix from fixes in here, probably
a good plan.
Signed-off-by: Dave Airlie <airlied@redhat.com>
SoCs like the rk3288 and rk3399 have 3 mipi dphys on them. One is TX-
only, one is RX-only and one can be configured to do either TX or RX.
The RX phy is statically connected to the first Image Signal Processor,
the TX phy is statically connected to the first DSI controller and
the TXRX phy is connected to both the second DSI controller as well
as the second ISP.
The RX dphy is controlled externally through registers in the "General
Register Files", while the other two are controlled through the
"Configuration and Test Interface" inside their DSI controller's
io-memory area.
The Rockchip dw-dsi controller already controls these dphys for the
TX case in the driver, but when we want to also allow configuration
for RX to the ISP from the media subsystem we need to expose phy-
functionality instead.
So add a bit of infrastructure to allow the dsi driver to work as a
phy and make sure it can be only one or the other at a time.
Similarly as the dsi-controller will be part of the drm-graph when
active, add an empty component to the drm-graph when in phy-mode
to make the rest of the drm-graph not wait for it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Tested-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Acked-by: Helen Koike <helen.koike@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210210111020.2476369-4-heiko@sntech.de
In a followup patch, we'll need to access the pclk ourself to enable some
functionality, so get and store it in the rockchip dw-dsi variant as well.
Clocks are refcounted, so possible cascading enablements are
no problem.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Tested-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Acked-by: Helen Koike <helen.koike@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210210111020.2476369-2-heiko@sntech.de
As nwl_dsi.lanes is u32, and NSEC_PER_SEC is 1000000000L, the second
multiplication in
dsi->lanes * 8 * NSEC_PER_SEC
will overflow on a 32-bit platform. Fix this by making the constant
unsigned long long, forcing 64-bit arithmetic.
As iMX8 is arm64, this driver is currently used on 64-bit platforms
only, where long is 64-bit, so this cannot happen. But the issue will
start to happen when the driver is reused for a 32-bit SoC (e.g.
i.MX7ULP), or when code is copied for a new driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ebb82941a86b4e35c4fcfb1ef5a5cfad7c1fceab.1626255956.git.geert+renesas@glider.be
Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.
v3:
* return error if (ret < 0) (Geert)
* remove duplicate error message (Geert)
v2:
* handle errors in platform_get_irq() (Geert, Sergei)
* store IRQ number in struct shmob_drm_device (Laurent)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720080941.23646-1-tzimmermann@suse.de
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-8-tzimmermann@suse.de
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-7-tzimmermann@suse.de
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-6-tzimmermann@suse.de
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-5-tzimmermann@suse.de
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
There's one left-over reference to the imported attachment that we
keep. GEM BOs with imported attachment are considered uncached and
enables special handling within the drm_fb_swab().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-4-tzimmermann@suse.de
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-3-tzimmermann@suse.de
Implement helpers drm_gem_fb_begin_cpu_access() and _end_cpu_access(),
which call the rsp dma-buf functions for all GEM BOs of the given
framebuffer.
Calls to dma_buf_end_cpu_access() can return an error code on failure,
while drm_gem_fb_end_cpu_access() does not. The latter runs during DRM's
atomic commit or during cleanup. Both cases don't allow for errors, so
leave out the return value.
v2:
* fix typo in docs (Daniel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-2-tzimmermann@suse.de
The variable 'priv' got introduced in commit 39a364a19e
("drm/hisilicon/hibmc: Convert to Linux IRQ interfaces") by accident.
It's unused; remove it. Fixes a compiler warning.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 39a364a19e ("drm/hisilicon/hibmc: Convert to Linux IRQ interfaces")
Reviewed-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: Dave Airlie <airlied@gmail.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Tian Tao <tiantao6@hisilicon.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721131704.10306-1-tzimmermann@suse.de
They are initalized by hardware during power up phase,
starting from sdma v5_2 generation
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In pass-through mode, after mode 1 reset, msix enablement status would
lost and never receives interrupt again. So, we should restore msix
status after mode 1 reset.
Signed-off-by: Chengzhe Liu <ChengZhe.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The fail reason is that the vfgate is disabled
Signed-off-by: Roy Sun <Roy.Sun@amd.com>
Reviewed-by: Peng Ju Zhou <PengJu.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Regression found in some embedded panels traces back to the earliest
upstreamed ASSR patch. The changed code flow are causing problems
with some panels.
[How]
- Change ASSR enabling code while preserving original code flow
as much as possible
- Simplify the code on guarding with internal display flag
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213779
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1620
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On Sienna Cichlid, in pass-through mode, if we unload the driver in BACO
mode(RTPM), then the kernel would receive thousands of interrupts.
That's because there is doorbell monitor interrupt on BIF, so KVM keeps
injecting interrupts to the guest VM. So we should clear the doorbell
interrupt status after BACO exit.
v2: Modify coding style and commit message
Signed-off-by: Chengzhe Liu <ChengZhe.Liu@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes a bug which if we probe a non-existing
I2C device, and the SMU returns 0xFF, from then on
we can never communicate with the SMU, because the
code before this patch reads and interprets 0xFF
as a terminal error, and thus we never write 0
into register 90 to clear the status (and
subsequently send a new command to the SMU.)
It is not an error that the SMU returns status
0xFF. This means that the SMU executed the last
command successfully (execution status), but the
command result is an error of some sort (execution
result), depending on what the command was.
When doing a status check of the SMU, before we
send a new command, the only status which
precludes us from sending a new command is 0--the
SMU hasn't finished executing a previous command,
and 0xFC--the SMU is busy.
This bug was seen as the following line in the
kernel log,
amdgpu: Msg issuing pre-check failed(0xff) and SMU may be not in the right state!
when subsequent SMU commands, not necessarily
related to I2C, were sent to the SMU.
This patch fixes this bug.
v2: Add a comment to the description of
__smu_cmn_poll_stat() to explain why we're NOT
defining the SMU FW return codes as macros, but
are instead hard-coding them. Such a change, can
be followed up by a subsequent patch.
v3: The changes are,
a) Add comments to break labels in
__smu_cmn_reg2errno().
b) When an unknown/unspecified/undefined result is
returned back from the SMU, map that to
-EREMOTEIO, to distinguish failure at the SMU
FW.
c) Add kernel-doc to
smu_cmn_send_msg_without_waiting(),
smu_cmn_wait_for_response(),
smu_cmn_send_smc_msg_with_param().
d) In smu_cmn_send_smc_msg_with_param(), since we
wait for completion of the command, if the
result of the completion is
undefined/unknown/unspecified, we print that to
the kernel log.
v4: a) Add macros as requested, though redundant, to
be removed when SMU consolidates for all
ASICs--see comment in code.
b) Get out if the SMU code is unknown.
v5: Rename the macro names.
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Evan Quan <evan.quan@amd.com>
Cc: Lijo Lazar <Lijo.Lazar@amd.com>
Fixes: fcb1fe9c9e ("drm/amd/powerplay: pre-check the SMU state before issuing message")
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Asic cyan_skilfish2 won't support RLC autoload when using
front door loading. We just use PSP to load firmware like
gfx9 here.
So add autoload_supported flag check instead of just
checking firmware load type for RLC autoload.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable SMU support for cyan_skilfish.
v2: Squash in fix (Alex)
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add check_fw_version function support for cyan_skillfish.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add basic ppt funcs support or cyan_skilfish.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Will switch to front door loading by default after this function is
stable.
v2: use APU flags (Alex)
Signed-off-by: Lang Yu <lang.yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add psp v11.0.8 to ip block initialization.
v2: use APU flags (Alex)
Signed-off-by: Lang Yu <lang.yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
nbio version is 2.3.
v2: Make it more explicit (Alex)
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add KFD support for cyan_skillfish.
v2: whitespace fixes (Alex)
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: squash in updates from Ray
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add gfx support for cyan_skillfish.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add gmc support for cyan_skillfish.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use backdoor loading.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Same as Navi10.
v2: squash in updates (Alex)
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add cp/rlc fw loading support and gfx golden setting.
v2: squash in updates (Alex)
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add ip blocks for cyan_skillfish.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use FAMILY_NV for cyan_skillfish.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add ip offset definition for cyan_skillfish and initialize it.
v2: squash in ip_offset updates (Alex)
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add Yellow Carp PCI id support.
v2: add another DID
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
0x1681 has a different external revision id.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: John Clements <John.Clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently all timedout job will be considered to be guilty. In SRIOV
multi-vf use case, the vf flr happens first and then job time out is
found. There can be several jobs timeout during a very small time slice.
And if the innocent sdma job time out is found before the real bad
job, then the innocent sdma job will be set to guilty. This will lead
to a page fault after resubmitting job.
[How]
If the job is a kernel job, we will always consider it not guilty
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix make htmldocs complaint:
./drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c:628: warning: Excess function parameter 'interrupt_params' description in 'DMUB_TRACE_MAX_READ'
v2:
Moved DMUB_TRACE_MAX_READ macro above function documentation
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
CC: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add new line to phy_settings output
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
start_cpsch and stop_cpsch can be called during kfd device
initialization or during gpu reset/recovery. So they can
run concurrently. Currently in start_cpsch and stop_cpsch,
pm_init and pm_uninit is not protected by the dpm lock.
Imagine such a case that user use packet manager's function
to submit a pm4 packet to hang hws (ie through command
cat /sys/class/kfd/kfd/topology/nodes/1/gpu_id | sudo tee
/sys/kernel/debug/kfd/hang_hws), while kfd device is under
device reset/recovery so packet manager can be not initialized.
There will be unpredictable protection fault in such case.
This patch moves pm_init/uninit inside the dpm lock and check
packet manager is initialized before using packet manager
function.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This variable will be used to determine whether packet
manager is initialized or not, in a future patch.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Renaming packets to packet_mgr to reflect the real meaning
of this variable.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Function name "psp_np_fw_load" is not proper as people don't
know _np_fw_ means "non psp firmware". Change the function
name to psp_load_non_psp_fw for better understanding. Same
thing for function psp_execute_np_fw_load.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The printing message "PSP loading VCN firmware" is mis-leading because
people might think driver is loading VCN firmware. Actually when this
message is printed, driver is just preparing some VCN ucode, not loading
VCN firmware yet. The actual VCN firmware loading will be in the PSP block
hw_init. Fix the printing message
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Squash in warning fix (Alex)
Signed-off-by: Roy Sun <Roy.Sun@amd.com>
Reviewed-by: Zhou pengju <pengju.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The callback functions are used for SRIOV read/write instead
of just for rlcg read/write
Signed-off-by: Roy Sun <Roy.Sun@amd.com>
Reviewed-by: Zhou pengju <pengju.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Similar to xGMI reporting the min/max bandwidth between direct peers, PCIe
will report the min/max bandwidth to the KFD.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Report the min/max bandwidth in megabytes to the kfd for direct
xgmi connections only. Indirect peers will report 0 since
indirect route is unknown.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The TA can now be invoked to provide the number of xgmi links connecting
a direct source and destination peer.
Non-direct peers will report zero links.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
make htmldocs complaints about parameter for amdgpu_bo_add_to_shadow_list
./drivers/gpu/drm/amd/amdgpu/amdgpu_object.c:739: warning: Excess function parameter 'bo' description in 'amdgpu_bo_add_to_shadow_list'
./drivers/gpu/drm/amd/amdgpu/amdgpu_object.c:739: warning: Function parameter or member 'vmbo' not described in 'amdgpu_bo_add_to_shadow_list'
./drivers/gpu/drm/amd/amdgpu/amdgpu_object.c:739: warning: Excess function parameter 'bo' description in 'amdgpu_bo_add_to_shadow_list'
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for board power calibration on Aldebaran.
Board calibration is done after DC offset calibration.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PMFW message which previously thought to only control Z9 controls both
Z9 and Z10. Also HW design team requested that Z9 must only be supported
on eDP due to content protection interop.
[How]
Change zstate support condition to match updated policy
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.145 brings improvements in multiple areas. In summary, we
highlight:
- Code improvements for passive
- Cursor manipulation enhancements
- Expand debug in some areas
- Fix problems in DML
- Other minor code refactors
Reviewed-by: Anson Jacob <Anson.Jacob@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add reserved bits for future feature development
- Fix issue with mismatch with type const
- Replaced problematic code with old memcpy and casted problematic
pointers to unsigned char pointers
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There's a special case where upper plane is not the main plane. If it owns
the cursor, it will be invisible in the majority of the screen.
[How]
The condition for disabling cursor is changed:
- check if upper viewport completely covers current. This was the
previous change that doesn't handle all scenarios with pipe splitting.
- if not, show the cursor only if it's not scaled or no upper pipe.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Populate dtbclk values from bwparams for dcn302, dcn303.
[How]
dtbclk values are fetched from bandwidthparams for all DPM levels and
for DPM levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When an riommu invalidation request come at the same time as a pipe is
disabled there can be a case where DCN cannot ACK the request if only
one VMID is setup in the inuse list.
[How]
Setup a second unused VMID will work around the issue.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DCN31 doesn't have MALL in DMUB so to avoid sending unknown commands to
DMUB just remove the function pointer.
[how]
Remove apply_idle_power_optimizations from function pointers structure
for DCN31
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When finding a second pipe for pipe split, currently will look for
bottom pipe in context first to decide the second pipe. This causes
issues in 2 plane to 1 plane transitions like fullscreen video where
bottom pipe no longer exists in the new configuration.
[HOW]
If previous context had an ODM pipe, use that to find the secondary pipe
first before looking at bottom pipe.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: sunglee <sunglee@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.
[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
We're missing a default value for dram_channel_width_bytes in the
DCN3.1 SOC bounding box and we don't currently have the interface in
place to query the actual value from VBIOS.
Put in a hardcoded default until we have the interface in place.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardcoding the VCO frequency isn't correct since we don't own or control
the value.
In the case where the hardcode is also missing we can't lightup display.
[How]
Query from the CLK register instead. Update the DFS frequency to be able
to compute the VCO frequency.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Initialize socclk entries in bandwidth params for dcn302, dcn303.
[How]
Fetch the sockclk values from smu for the DPM levels and for the DPM
levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Vertical and horizontal borders in timings are treated as increasing the
active area - vblank and hblank actually shrink.
Our input into DML does not include these borders so it incorrectly
assumes it has more time than available for vstartup and tmdl
calculations for some modes with borders.
An example of such a timing would be 640x480@72Hz:
h_total: 832
h_border_left: 8
h_addressable: 640
h_border_right: 8
h_front_porch: 16
h_sync_width: 40
v_total: 520
v_border_top: 8
v_addressable: 480
v_border_bottom: 8
v_front_porch: 1
v_sync_width: 3
pix_clk_100hz: 315000
[How]
Include borders as part of destination vactive/hactive.
This change DCN20+ so it has wide impact, but the destination vactive
and hactive are only really used for vstartup calculation anyway.
Most modes do not have vertical or horizontal borders.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A comparison error made it possible to not iterate through all the
specified prefetch modes.
[how]
Correct "<" to "<="
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Yongqiang Sun <Yongqiang.Sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During headless boot, DIG may be on which causes HW/SW discrepancies.
To avoid this we power down hardware on boot if DIG is turned on. With
introduction of multiple eDP, hardware power down is being bypassed
under certain conditions.
[How]
Fixed hardware power down bypass, and ensured hardware will power down
if DIG is on and seamless boot is not enabled.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Theoretically, per DP 1.4a spec, sink device needs to AUX_ACK 00340h
write. However, due to hardware limitation, some sink devices have no
00340h dpcd address at all. This results in sink side fails to reply
ACK, and consequently cause source side keep retrying DPCD write on DPCD
00340h. This results in significant delay when DPCD 00340h write is
triggered (e.g. at S3 resume).
[How]
Check whether sink device could ACK on DPCD 00340h write on boot. If
sink device fails to ACK, then remember that, so we won't write to DPCD
00340h later on.
There will be a drm.debug KMS level message to inform user once a 00340h
DPCD write is skipped on purpose.
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Print a debug message when dcc validation fails in the display driver.
Most DCC enablement related errors are from userspace. Adding a debug
print in case of a failure from display driver will aid quicker triage.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set a condition for the message of "Couldn't set OPP regulators" to not
display if the error code is EPROBE_DEFER. Note that I used an if
statement to capture the condition instead of the dev_err_probe
function because I didn't want to change the DRM_DEV_ERROR usage.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721214830.25690-1-macroalpha82@gmail.com
UAPI Changes:
- Remove sysfs stats for dma-buf attachments, as it causes a performance regression.
Previous merge is not in a rc kernel yet, so no userspace regression possible.
Cross-subsystem Changes:
- Sanitize user input in kyro's viewport ioctl.
- Use refcount_t in fb_info->count
- Assorted fixes to dma-buf.
- Extend x86 efifb handling to all archs.
- Fix neofb divide by 0.
- Document corpro,gm7123 bridge dt bindings.
Core Changes:
- Slightly rework drm master handling.
- Cleanup vgaarb handling.
- Assorted fixes.
Driver Changes:
- Add support for ws2401 panel.
- Assorted fixes to stm, ast, bochs.
- Demidlayer ingenic irq.
-----BEGIN PGP SIGNATURE-----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=BUya
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-07-22' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.15-rc1:
UAPI Changes:
- Remove sysfs stats for dma-buf attachments, as it causes a performance regression.
Previous merge is not in a rc kernel yet, so no userspace regression possible.
Cross-subsystem Changes:
- Sanitize user input in kyro's viewport ioctl.
- Use refcount_t in fb_info->count
- Assorted fixes to dma-buf.
- Extend x86 efifb handling to all archs.
- Fix neofb divide by 0.
- Document corpro,gm7123 bridge dt bindings.
Core Changes:
- Slightly rework drm master handling.
- Cleanup vgaarb handling.
- Assorted fixes.
Driver Changes:
- Add support for ws2401 panel.
- Assorted fixes to stm, ast, bochs.
- Demidlayer ingenic irq.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2d0d2fe8-01fc-e216-c3fd-38db9e69944e@linux.intel.com
and fence error propagation and a GVT fix of shadow ppgtt invalidation
with proper D3 state tracking from Colin.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmD5dZ4ACgkQ+mJfZA7r
E8oOjggAmpH/KcwfiQMoVx8ie28bO5bZzLTX05Cchi1DJ3Av3WuHFalekw+3AAJc
s58fU2eLp/FKZ796OPNZLtmVgA2984UioDI9TePUn5kQ0PixJh5p7hpuywDBafpH
C8jgp1dPbMDtTZGbLLt40tJYDNFKnaqQXiTYeDsqXhqlELcD9wfiqU6MwnBkmuoC
kAdYvHcXrnnavfT7faXW3VFhJWYPB5Ow9tFXG2taeGXlh08Jsb6pek/eukgHKmkP
10leCkrYVpCbju2LJnUMwX4cV9cxfF4hYPakB/TpuvH8QeMD2tFWuEjljCgxI5BR
l1spFg7NSiuMAsN5wocLFDvY3Y3hHw==
=jhBB
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-fixes-2021-07-22' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Couple reverts from Jason getting rid of asynchronous command parsing
and fence error propagation and a GVT fix of shadow ppgtt invalidation
with proper D3 state tracking from Colin.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YPl1sIyruD0U5Orl@intel.com
[Why]
Regression found in some embedded panels traces back to the earliest
upstreamed ASSR patch. The changed code flow are causing problems
with some panels.
[How]
- Change ASSR enabling code while preserving original code flow
as much as possible
- Simplify the code on guarding with internal display flag
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213779
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1620
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Add Yellow Carp PCI id support.
v2: add another DID
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
0x1681 has a different external revision id.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for board power calibration on Aldebaran.
Board calibration is done after DC offset calibration.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PMFW message which previously thought to only control Z9 controls both
Z9 and Z10. Also HW design team requested that Z9 must only be supported
on eDP due to content protection interop.
[How]
Change zstate support condition to match updated policy
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Populate dtbclk values from bwparams for dcn302, dcn303.
[How]
dtbclk values are fetched from bandwidthparams for all DPM levels and
for DPM levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DCN31 doesn't have MALL in DMUB so to avoid sending unknown commands to
DMUB just remove the function pointer.
[how]
Remove apply_idle_power_optimizations from function pointers structure
for DCN31
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.
[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
We're missing a default value for dram_channel_width_bytes in the
DCN3.1 SOC bounding box and we don't currently have the interface in
place to query the actual value from VBIOS.
Put in a hardcoded default until we have the interface in place.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
