The delay here is not in atomic context and does not seem critical with
respect to precision, but usleep_range(min,max) with min==max results in
giving the timer subsystem no room to optimize uncritical delays. Fix
this by setting the range to 2000,3000 us.
Fixes: commit f05259a6ff ("clk: wm831x: Add initial WM831x clock driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On vf610, PLL1 and PLL2 have registers to configure fractional part of
frequency multiplier.
This patch adds support for these registers.
This fixes "fast system clock" issue on boards where bootloader sets
fractional multiplier for PLL1.
Suggested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
CC: Chris Healy <cphealy@gmail.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current driver code gives the crash or gets hang while switching
the CPU frequency some time. The APSS CPU Clock divider is not glitch
free so it the APPS clock need to be switched for stable clock during
the change.
This patch adds the frequency change notifier for APSS CPU clock. It
changes the parent of this clock to stable PLL FEPLL500 for
PRE_RATE_CHANGE event. This event will be generated before actual
clock set operations. The clock set operation will again change its
corresponding parent by getting the same from frequency table.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
[sboyd@codeaurora.org: Indent less in probe]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock and reset controller use same compatible strings (same IP).
Since commit 989eafd0b6 ("clk: core: Avoid double initialization of
clocks") the OF core flags clock controllers registered with the
CLK_OF_DECLARE() macro as OF_POPULATED, so platform devices with the same
compatible string will not be registered.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The RZ/A1 is different than the other Renesas SOCs because the MSTP
registers are 8-bit instead of 32-bit and if you try writing values as
32-bit nothing happens...meaning this driver never worked for r7s72100.
Fixes: b6face404f ("ARM: shmobile: r7s72100: add essential clock nodes to dtsi")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In the stm32f469 soc, the 48Mhz clock could be derived from pll-q or
from pll-sai-p.
The SDIO clock could be also derived from 48Mhz or from sys clock.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch introduces SAI clocks for stm32f4 socs.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch introduces I2S clock for stm32f4 soc.
The I2S clock could be derived from an external clock or from pll-i2s
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch introduces lcd-tft clock for stm32f4 soc.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds post dividers of I2S & SAI PLLs.
These dividers are managed by a dedicated register (RCC_DCKCFGR).
The PLL should be off before a set rate.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch introduces PLL_I2S and PLL_SAI.
Vco clock of these PLLs can be modify by DT (only n multiplicator,
m divider is still fixed by the boot-loader).
Each PLL has 3 dividers. PLL should be off when we modify the rate.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@codeaurora.org: Mark stm32f4_pll_div_ops static]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds all RPM based clocks for msm8974, except cxo and
gfx3d_clk_src.
Tested-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The APSS CPU clock does not contain all the frequencies in its
frequency table so this patch adds the same.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
1. The parent for sdcc clock is sdccpll.
2. The frequency value was wrong so modified the same.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver does not have the node for
PCNOC so this patch adds and registers the PCNOC clock nodes.
This PCNOC clock is critical and should not be turned off so
setting CRITICAL flag also.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver does not have support for all
the frequency supported by APSS CPU. APSS CPU frequency is
provided with APSS CPU PLL divider which divides down the VCO
frequency. This divider is nonlinear and specific to IPQ4019
so the standard divider code cannot be used for this.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver registered the PLL clocks and
dividers as fixed clock. These fixed clock needs to be removed
from driver probe function and same need to be registered with
clock framework. These PLL clocks should be programmed only
once and the same are being programmed already by the boot
loader so the set rate operation is not required for these
clocks. Only the rate can be calculated by clock operations
in clock driver file so this patch adds the same.
The PLL takes the reference clock from XO and generates the
intermediate VCO frequency. This VCO frequency will be divided
down by different PLL internal dividers. Some of the PLL
internal dividers are fixed while other are programmable.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull ARM updates from Russell King:
- an update for clkdev registration error detection to simplify users
- add cpu capacity parsing from DT
- support for larger cachelines found on UniPhier caches
- documentation for udelay constants
- properly tag assembly function declarations
- remove unnecessary indirection of asm/mach-types.h
- switch to syscall table based generation to simplify future additions
of system calls, along with correpsonding commit for pkey syscalls
- remove redundant sa1101 header file
- RONX protect modules when they're in the vmalloc region
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: mm: allow set_memory_*() to be used on the vmalloc region
ARM: mm: fix set_memory_*() bounds checks
ARM: 8631/1: clkdev: Detect errors in clk_hw_register_clkdev() for mass registration
ARM: 8629/1: vfp: properly tag assembly function declarations in C code
ARM: 8622/3: add sysfs cpu_capacity attribute
ARM: 8621/3: parse cpu capacity-dmips-mhz from DT
ARM: 8623/1: mm: add ARM_L1_CACHE_SHIFT_7 for UniPhier outer cache
ARM: Update mach-types
ARM: sa1100: remove SA-1101 header file
ARM: 8619/1: udelay: document the various constants
ARM: wire up new pkey syscalls
ARM: convert to generated system call tables
ARM: remove indirection of asm/mach-types.h
These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2,
this is an new variant of the the DRA72x/DRA74x automotive
infotainment chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7
based microcontroller we support, related to the smaller
STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile,
see http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to
removing support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the
memory controller using 'perf'
Conflicts:
arch/arm/mach-shmobile/setup-rcar-gen2.c: rcar_gen2_clocks_init()
is gone, calling of_clk_init(NULL) is sufficient now.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BF6Y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2, this
is an new variant of the the DRA72x/DRA74x automotive infotainment
chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7 based
microcontroller we support, related to the smaller STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile, see
http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to removing
support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the memory
controller using 'perf'"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (95 commits)
ARM: davinci: da830-evm: use gpio descriptor for mmc pins
ARM: davinci: da850-evm: use gpio descriptor for mmc pins
ARM: davinci: hawk: use gpio descriptor for mmc pins
ARM: ARTPEC-6: add select MFD_SYSCON to MACH_ARTPEC6
ARM: davinci: da8xx: Fix ohci device name
ARM: oxnas: Add OX820 config and makefile entry
ARM: oxnas: Add OX820 SMP support
ARM: davinci: PM: fix build when da850 not compiled in
ARM: orion5x: remove legacy support of ls-chl
ARM: integrator: drop EBI access use syscon
ARM: BCM5301X: Add back handler ignoring external imprecise aborts
ARM: davinci: PM: support da8xx DT platforms
ARM: davinci: PM: cleanup: remove references to pdata
ARM: davinci: PM: rework init, remove platform device
ARM: Kconfig: Introduce MACH_STM32F746 flag
ARM: mach-stm32: Add a new SOC - STM32F746
ARM: shmobile: document SK-RZG1E board
ARM: shmobile: r8a7745: basic SoC support
ARM: imx: mach-imx6ul: add imx6ull support
ARM: zynq: Reserve correct amount of non-DMA RAM
...
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of
the machines that are still normally used with classic board files.
One tegra fix is important for new bootloader versions, but the
bug has been around for a while without anyone noticing.
The other changes are mostly cosmetic.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i2l2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of the
machines that are still normally used with classic board files. One
tegra fix is important for new bootloader versions, but the bug has
been around for a while without anyone noticing.
The other changes are mostly cosmetic"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: tegra: Add missing Smaug revision
arm64: tegra: Add VDD_GPU regulator to Jetson TX1
arm64: dts: zte: clean up gic-v3 redistributor properties
arm64: dts: zx: Fix gic GICR property
bus: vexpress-config: fix device reference leak
soc: ti: qmss: fix the case when !SMP
ARM: lpc32xx: drop duplicate header device.h
ARM: ixp4xx: drop duplicate header gpio.h
ARM: socfpga: fix spelling mistake in error message
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
ARM: OMAP2+: Remove the omapdss_early_init_of() function
mfd: tps65217: Fix mismatched interrupt number
ARM: zx: Fix error handling
ARM: spear: Fix error handling
ARM: davinci: da850: Fix pwm name matching
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
...
best_rate is reported as potentially uninitialized by gcc.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 155e8b3b0e ("clk: bcm: Support rate change propagation on bcm2835 clocks")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some driver is using this type of DT bindings for clock (more detail,
see ${LINUX}/Documentation/devicetree/bindings/sound/simple-card.txt).
sound_soc {
...
cpu {
clocks = <&xxx>;
...
};
codec {
clocks = <&xxx>;
...
};
};
Current driver in this case uses of_clk_get() for each node, but there
is no devm_of_clk_get() today.
OTOH, the problem of having devm_of_clk_get() is that it encourages the
use of of_clk_get() when clk_get() is more desirable.
Thus, this patch adds new devm_get_clk_from_chile() which explicitly
reads as get a clock from a child node of this device.
By this function, we can also use this type of DT bindings
sound_soc {
clocks = <&xxx>, <&xxx>;
clock-names = "cpu", "codec";
clock-ranges;
...
cpu {
...
};
codec {
...
};
};
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[sboyd@codeurora.org: Rename subject to clk + add API]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Free memory mapping, if probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Free memory mapping, if of_pll_div_clk_init is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Free memory and memory mapping , if mmp2_clk_init is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
[sboyd@codeaurora.org: Put return at the right place]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Free memory and memory mapping , if pxa910_clk_init is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
It is likely that instead of '1>64', 'q>64' was expected.
Moreover, according to datasheet,
http://www.ti.com/lit/ds/symlink/cdce925.pdf
SCAS847I - JULY 2007 - REVISED OCTOBER 2016
PLL settings limits are: 16 <= q <= 63
So change the upper limit check from 64 to 63.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The broadcom clk driver Kconfig file selects and depends on the
COMMON_CLK_IPROC config for different SoC specific drivers. Let's
simplify this by always selecting the COMMON_CLK_IPROC config,
turning it into a set of library code. We still want to retain
the SoC specific options, so we leave those in place. Since we're
here we also drop COMMON_CLK dependency because that's implicitly
handled by including this file in drivers/clk/Kconfig in the
right place and also make CLK_BCM_KONA default to y on the
architecture it exists for instead of plain default y.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The VEC clock requires needs to be set at exactly 108MHz. Allow rate
change propagation on PLLH_AUX to match this requirement wihtout
impacting other IPs (PLLH is currently only used by the HDMI encoder,
which cannot be enabled when the VEC encoder is enabled).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some peripheral clocks, like the VEC (Video EnCoder) clock need to be set
to a precise rate (in our case 108MHz). With the current implementation,
where peripheral clocks are not allowed to forward rate change requests
to their parents, it is impossible to match this requirement unless the
bootloader has configured things correctly, or a specific rate has been
assigned through the DT (with the assigned-clk-rates property).
Add a new field to struct bcm2835_clock_data to specify which parent
clocks accept rate change propagation, and support set rate propagation
in bcm2835_clock_determine_rate().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
bcm2835_pll_divider_off() is resetting the divider field in the A2W reg
to zero when disabling the clock.
Make sure we preserve this value by reading the previous a2w_reg value
first and ORing the result with A2W_PLL_CHANNEL_DISABLE.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The OMAP36xx DPLL5, driving EHCI USB, can be subject to a long-term
frequency drift. The frequency drift magnitude depends on the VCO update
rate, which is inversely proportional to the PLL divider. The kernel
DPLL configuration code results in a high value for the divider, leading
to a long term drift high enough to cause USB transmission errors. In
the worst case the USB PHY's ULPI interface can stop responding,
breaking USB operation completely. This manifests itself on the
Beagleboard xM by the LAN9514 reporting 'Cannot enable port 2. Maybe the
cable is bad?' in the kernel log.
Errata sprz319 advisory 2.1 documents PLL values that minimize the
drift. Use them automatically when DPLL5 is used for USB operation,
which we detect based on the requested clock rate. The clock framework
will still compute the PLL parameters and resulting rate as usual, but
the PLL M and N values will then be overridden. This can result in the
effective clock rate being slightly different than the rate cached by
the clock framework, but won't cause any adverse effect to USB
operation.
Signed-off-by: Richard Watts <rrw@kynesim.co.uk>
[Upported from v3.2 to v4.9]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix bug https://bugzilla.kernel.org/show_bug.cgi?id=188561. Function
wm831x_clkout_is_prepared() returns "true" when it fails to read
CLOCK_CONTROL_1. "true" means the device is already prepared. So
return "true" on the read failure seems improper.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Fixes: f05259a6ff ("clk: wm831x: Add initial WM831x clock driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add more data to 64bit SoCs for the cpufreq support.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Core support code for CPU frequency changes, which will be used by
the generic cpufreq driver.
The register view is different from the generic clk-mux; it has
a separate status register, and an update bit to load the register
setting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull rockchip clk driver updates from Heiko Stuebner:
A new clock controller for the rk1108 soc (single-core Cortex-A7+DSP),
a fix making sure the cpuclk rate is actually valid, before trying to
set it and a copy-paste fix for the rk3399's testclk.
* tag 'v4.10-rockchip-clk2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: add clock controller for rk1108
dt-bindings: add documentation for rk1108 cru
clk: rockchip: add dt-binding header for rk1108
clk: rockchip: fix copy-paste error in rk3399 testclk
clk: rockchip: validity should be checked prior to cpu clock rate change
The venus video ip's internal core blocks are under the
control of the firmware and their powerdomains needs to be
'ON' only when used by the firmware. So putting it into
hw controlled mode lets this to happen, otherwise the firmware
hangs checking for this.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some GDSCs might support a HW control mode, where in the power
domain (gdsc) is brought in and out of low power state (while
unsued) without any SW assistance, saving power.
Such GDSCs can be configured in a HW control mode when powered on
until they are explicitly requested to be powered off by software.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
With commit f4e8715099 ("clk: iproc: Make clocks visible options"),
COMMON_CLK_IPROC gained a dependency on ARCH_BCM_IPROC, yet CLK_BCM_63XX
also selects that option, this causes the following Kconfig warning:
warning: (CLK_BCM_63XX) selects COMMON_CLK_IPROC which has unmet direct
dependencies ((ARCH_BCM_IPROC || COMPILE_TEST) && COMMON_CLK)
Fix this by adding proper depends for COMMON_CLK_IPROC
Fixes: f4e8715099 ("clk: iproc: Make clocks visible options")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
[sboyd@codeaurora.org: Drop default part as it's redundant]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In the user manual of A33 SoC, the bit 22 and 23 of pll-mipi control
register is called "LDO{1,2}_EN", and according to the BSP source code
from Allwinner [1], the LDOs are enabled during the clock's enabling
process.
The clock failed to generate output if the two LDOs are not enabled.
Add the two bits to the clock's gate bits, so that the LDOs are enabled
when the PLL is enabled.
[1] https://github.com/allwinner-zh/linux-3.4-sunxi/blob/master/drivers/clk/sunxi/clk-sun8iw5.c#L429
Fixes: d05c748bd7 ("clk: sunxi-ng: Add A33 CCU support")
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There is no fixed divider on pllh_aux.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the clk_hw references to the actual clocks and add a xlate function
to return the hw pointers from the already existing static array.
Reported-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the clk_hw references to the actual clocks and add a xlate function
to return the hw pointers from the already existing static array.
Reported-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The sdcc driver for msm8996/msm8916/msm8974/msm8994 and apq8084
expects a clk_set_rate() on the sdcc rcg clk to set
a floor value of supported clk rate closest to the requested
rate, by looking up the frequency table.
So move all the sdcc rcgs on all these platforms to use the
newly introduced clk_rcg2_floor_ops
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
