This patch adds a dedicated self_test_reg variable. This is also a step
to let new drivers make use of `adis_initial_startup()`. Some devices
use MSG_CTRL reg to request a self_test command while others use the
GLOB_CMD register.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change splits the __adis_initial_startup() away from
adis_initial_startup(). The unlocked version can be used in certain calls
during probe, where races won't happen since the ADIS driver may not be
registered yet with IIO.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change overrides commit 380b107bbf ("iio: adis: Introduce timeouts
structure"). It removes the memory allocation and moves the 'adis_data'
information to be static on the chip_info struct.
This also adds a timeout structure to ADIS16334, since it was initially
omitted. This was omitted (by accident) when the change was done.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change overrides commit 380b107bbf ("iio: adis: Introduce timeouts
structure"). It removes the memory allocation and moves the 'adis_data'
information to be static on the chip_info struct.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing return value check in st_lsm6dsx_shub_read_oneshot disabling
the slave device connected to the st_lsm6dsx i2c controller.
The issue is reported by coverity with the following error:
Unchecked return value:
If the function returns an error value, the error value may be mistaken
for a normal value.
Addresses-Coverity-ID: 1456767 ("Unchecked return value")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As every chip has some little variant in LPF bandwidth values,
use common values that are working for all chips.
Simplify the LPF setting function.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Same generation as ICM20602 but different registers.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Automotive certified IMU, similar to ICM20608.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
They are similar to ICM20608 chip.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device_get_match_data for using of and acpi tables.
In spi support add missing mpu6515 and of match table.
Reorganize Kconfig to display chips grouped by generations.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
odr to odr_table
gain to fs_table
'gain' is actually in 'st_lsm6dsx_fs' structure of 'fs_table'
Signed-off-by: JieunKim <jieun.kim4758@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Allow to read the mount-matrix device tree property and provide the
mount_matrix file for userspace to read.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS16490 is part of the same family with ADIS16495 and ADIS16497,
the main difference is the temperature, accelerometer and gyroscope
scales.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/adis16490.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make mpu6050 usable on platforms which provide only any-edge interrupts.
One example of this kind of platform is AT91SAM9G45
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of temperature data in fifo for all chips.
Enable unification of scan elements for icm20602.
Add macros for generating scan elements.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current `delay_usecs`
with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing return value check in st_lsm6dsx_read_oneshot disabling the
sensor. The issue is reported by coverity with the following error:
Unchecked return value:
If the function returns an error value, the error value may be mistaken
for a normal value.
Addresses-Coverity-ID: 1446733 ("Unchecked return value")
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Fixes: 290a6ce11d ("iio: imu: add support to lsm6dsx driver")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
At the moment, attempting to probe a device with ST_LSM6DS3_ID
(e.g. using the st,lsm6ds3 compatible) fails with:
st_lsm6dsx_i2c 1-006b: unsupported whoami [69]
... even though 0x69 is the whoami listed for ST_LSM6DS3_ID.
This happens because st_lsm6dsx_check_whoami() also attempts
to match unspecified (zero-initialized) entries in the "id" array.
ST_LSM6DS3_ID = 0 will therefore match any entry in
st_lsm6dsx_sensor_settings (here: the first), because none of them
actually have all 12 entries listed in the "id" array.
Avoid this by additionally checking if "name" is set,
which is only set for valid entries in the "id" array.
Note: Although the problem was introduced earlier it did not surface until
commit 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
because ST_LSM6DS3_ID was the first entry in st_lsm6dsx_sensor_settings.
Fixes: d068e4a0f9 ("iio: imu: st_lsm6dsx: add support to multiple devices with the same settings")
Cc: <stable@vger.kernel.org> # 5.4
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All timeouts are now handled by a dedicated timeout struct. This
variable is no longer needed.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adis library only allows to define a `startup_delay` which for some
devices is enough. However, other devices define different timeouts with
significantly different timings which could lead to devices to not wait
enough time or to wait a lot more than necessary (which is not
efficient). This patch introduces a new timeout struct that must be
passed into `adis_init()`. There are mainly, for now, three timeouts
used. This is also an introductory patch with the goal of refactoring
`adis_initial_startup()`. New driver's (eg: adis16480, adis16460) are
replicating code for the device initial setup. With some changes (being
this the first one) we can pass this to `adis_initial_startup()`.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
-----BEGIN PGP SIGNATURE-----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=8FmM
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.6 cycle
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
* tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (99 commits)
iio: accel: bma180: BMA254 support
iio: pressure: bmp280: Allow device to be enumerated from ACPI
iio: pressure: bmp280: Drop ACPI support
dt-bindings: iio: adc: convert sd modulator to json-schema
iio: buffer: rename 'read_first_n' callback to 'read'
iio: buffer-dmaengine: Report buffer length requirements
bindings: iio: pressure: Add documentation for dlh driver
dt-bindings: Add asc vendor
iio: pressure: Add driver for DLH pressure sensors
iio: buffer-dmaengine: Add module information
iio: accel: bma180: Use explicit member assignment
iio: accel: bma180: Basic regulator support
iio: accel: bma180: Add dev helper variable
iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm
iio: imu: st_lsm6dsx: rename st_lsm6dsx_shub_read_reg in st_lsm6dsx_shub_read_output
iio: imu: st_lsm6dsx: check if shub_output reg is located in primary page
iio: imu: st_lsm6dsx: check if pull_up is located in primary page
iio: imu: st_lsm6dsx: check if master_enable is located in primary page
iio: imu: st_lsm6dsx: export max num of slave devices in st_lsm6dsx_shub_settings
iio: light: remove unneeded semicolon
...
Enabled i2c master controller support for LSM6DSM sensor. Enable
ext_sensor0 for lsm6dsm. This series has been tested using LIS2MDL as
slave device connected to the i2c controller of the LSM6DSM
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rename st_lsm6dsx_shub_read_reg routine in st_lsm6dsx_shub_read_output
since it is used to read from sensorhub channel0 output register
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check if the sensor hub output register is located in the primary or in the
secondary memory page. This is a preliminary patch to support i2c master
controller on lsm6dsm devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check if the pull up register is located in the primary or in the
secondary memory page. This is a preliminary patch to support i2c master
controller on lsm6dsm devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check if the master enable register is located in the primary or in the
secondary memory page. This is a preliminary patch to support i2c master
controller on lsm6dsm devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Export max number of slave devices supported by the i2c master
controller in st_lsm6dsx_shub_settings data structure.
This is a preliminary patch to support i2c master controller
on lsm6dsm sensors
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no need to have OF guard against ID table.
Drop it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.
Mark predefined constants with __maybe_unused to calm a compiler down:
In file included from drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c:17:
.../st_lsm6dsx/st_lsm6dsx.h:399:28: warning: ‘st_lsm6dsx_available_scan_masks’ defined but not used [-Wunused-const-variable=]
399 | static const unsigned long st_lsm6dsx_available_scan_masks[] = {0x7, 0x0};
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
.../st_lsm6dsx/st_lsm6dsx.h:392:36: warning: ‘st_lsm6dsx_event’ defined but not used [-Wunused-const-variable=]
392 | static const struct iio_event_spec st_lsm6dsx_event = {
| ^~~~~~~~~~~~~~~~
...
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix following checkpatch warning:
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
commit f7072198f2 ("iio: imu: Fix inv_mpu6050 dependencies")
undid the explicit selection of I2C_MUX previously
done by the driver, because I2C_MUX implicitly depended
on HAS_IOMEM.
However commit 93d710a65e ("i2c: mux: fix up dependencies")
cleared up the situation properly and drivers that need
to select I2C_MUX can now do so again.
It makes a lot of sense for a driver to select the driver
infrastructure it needs so restore the natural order of
things.
Cc: Richard Weinberger <richard@nod.at>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.
Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.
* ad7606
- Avoid reading extra data from the device over what was intended.
* ad7124
- Enable the internal reference when in use.
* ad7292
- Fix up license for newly added binding. Better to not have this go
out in a release with more limited header than intended.
- Fix a constraint on number of channels.
* ad7949
- Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
- Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
- Allocate right amount of private data (currently allocating too much).
* ltc2983
- Avoid a potential issue with machine endianness and wrong length device
tree read.
* max1027
- Clean up leak of an iio_trigger on probe failure.
* max9611
- Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
- Fix wrong ABI usage (units) for temperature channel.
* st_accel
- Fix an unused variable warning.
* st_lsm6dsx
- Fix decimation factor issue that can lead to missaligned datasets
(and hence garbage)
- Fix an issue with how we track enabled fifo channels.
- Avoid powering off the device if wake up events are enabled.
-----BEGIN PGP SIGNATURE-----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=vySY
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of fixes for IIO in the 5.5 cycle.
Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.
Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.
* ad7606
- Avoid reading extra data from the device over what was intended.
* ad7124
- Enable the internal reference when in use.
* ad7292
- Fix up license for newly added binding. Better to not have this go
out in a release with more limited header than intended.
- Fix a constraint on number of channels.
* ad7949
- Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
- Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
- Allocate right amount of private data (currently allocating too much).
* ltc2983
- Avoid a potential issue with machine endianness and wrong length device
tree read.
* max1027
- Clean up leak of an iio_trigger on probe failure.
* max9611
- Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
- Fix wrong ABI usage (units) for temperature channel.
* st_accel
- Fix an unused variable warning.
* st_lsm6dsx
- Fix decimation factor issue that can lead to missaligned datasets
(and hence garbage)
- Fix an issue with how we track enabled fifo channels.
- Avoid powering off the device if wake up events are enabled.
* tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: max9611: Fix too short conversion time delay
iio: ad7949: fix channels mixups
iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
iio: imu: st_lsm6dsx: fix decimation factor estimation
iio: imu: inv_mpu6050: fix temperature reporting using bad unit
iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
iio: adc: max1027: fix not unregistered iio trigger
iio: adc: intel_mrfld_adc: Allocating too much data in probe()
iio: adc: ad7124: Enable internal reference
dt-bindings: iio: adc: ad7292: fix constraint over channel quantity
dt-bindings: iio: adc: ad7292: Update SPDX identifier
iio: temperature: ltc2983: fix u32 read into a unsigned long long
iio: st_accel: Fix unused variable warning
iio: adc: ad7606: fix reading unnecessary data from device
Do not power-off accel unconditionally if wake-up events are enabled
powering off the hw FIFO. At the same time do not power-off the accel
sensor if it is 'batched' in the hw FIFO disabling sensor events
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Track hw FIFO state introducing fifo_mask since now the accel sensor
can be enabled during suspend/resume in order to trigger the wake-up
enabling the FIFO in st_lsm6dsx_resume even if it was disabled before
the suspend. Hence we must separately track the fifo state.
Fixes: 4c997dfa69 ("iio: imu: st_lsm6dsx: add wakeup-source option")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix decimation factor and sip estimation for LSM6DSM series
(max value for decimation factor is 32).
If gyro and accel sensors are enabled at 12.5Hz and 416Hz
respectively, decimation factor lookup will fail, producing
unaligned data.
Remove unused decimator filed in st_lsm6dsx_sensor structure.
Fixes: f8710f0357 ("iio: imu: st_lsm6dsx: express odr in mHZ")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Temperature should be reported in milli-degrees, not degrees. Fix
scale and offset values to use the correct unit.
This is a fix for an issue that has been present for a long time.
The fixes tag reflects the point at which the code last changed in a
fashion that would make this fix patch no longer apply. Backports
will be necessary to fix those elements that predate that patch.
Fixes: 1615fe41a1 ("iio: imu: mpu6050: Fix FIFO layout for ICM20602")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging and iio set of patches for the 5.5-rc1 release.
It's the usual huge collection of cleanup patches all over the
drivers/staging/ area, along with a new staging driver, and a bunch of
new IIO drivers as well.
Full details are in the shortlog, but all of these have been in
linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6lVQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylFnwCgyvZ62uUyQTRey0zvNTe3I4fY9L4AnAnrz3ZC
U6ZA2+Uj3O6qhAr5frRu
=uv8S
-----END PGP SIGNATURE-----
Merge tag 'staging-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / iio updates from Greg KH:
"Here is the big staging and iio set of patches for the 5.5-rc1
release.
It's the usual huge collection of cleanup patches all over the
drivers/staging/ area, along with a new staging driver, and a bunch of
new IIO drivers as well.
Full details are in the shortlog, but all of these have been in
linux-next for a long time with no reported issues"
* tag 'staging-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (548 commits)
staging: vchiq: Have vchiq_dump_* functions return an error code
staging: vchiq: Refactor indentation in vchiq_dump_* functions
staging: fwserial: Fix Kconfig indentation (seven spaces)
staging: vchiq_dump: Replace min with min_t
staging: vchiq: Fix block comment format in vchiq_dump()
staging: octeon: indent with tabs instead of spaces
staging: comedi: usbduxfast: usbduxfast_ai_cmdtest rounding error
staging: most: core: remove sysfs attr remove_link
staging: vc04: Fix Kconfig indentation
staging: pi433: Fix Kconfig indentation
staging: nvec: Fix Kconfig indentation
staging: most: Fix Kconfig indentation
staging: fwserial: Fix Kconfig indentation
staging: fbtft: Fix Kconfig indentation
fbtft: Drop OF dependency
fbtft: Make use of device property API
fbtft: Drop useless #ifdef CONFIG_OF and dead code
fbtft: Describe function parameters in kernel-doc
fbtft: Make sure string is NULL terminated
staging: rtl8723bs: remove set but not used variable 'change', 'pos'
...
It's the only operation that does 2 operations (a read & a write), so the
unlocked functions can be used under a single state lock.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change removes the use of indio_dev's mlock in favor using the state
lock from the ADIS library.
The set_freq() & get_freq() hooks are unlocked, so they require specific
locking. That is because in some cases the get_freq() hook is used in
combination with adis16400_set_filter().
In cases where only one read/write is done, the functions that hold the
state lock are used.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The single conversion function does a series of reads + writes. This change
extends the use of the state_lock for the entire set of operations.
Previously, indio_dev's mlock was used. This change also removes the use of
this lock.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The initial startup routine is called by some ADIS drivers during probe,
and before registering with IIO. Normally, userspace should not be able to
do any access to the device (as there shouldn't be any available).
This change extends the state lock to the entire initial-startup routine.
Behaviourally nothing should change, but this should make the library
function a bit more robust.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The reset routine may also be important to be protected by the state-lock
and grouped with other operations, so create an unlocked version, so that
this can be done.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This one also gets re-used in certain operations, so it makes sense to
have an unlocked version of this to group it with other
reads/writes/operations to have a single lock for the whole state change.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adis_enable_irq() does a read & a write. This change keeps a lock for
the duration of both operations vs for each op.
The change is also needed in adis16480, since that has it's own
implementation for adis_enable_irq().
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This will allow more flexible control to group reads & writes into a single
lock (particularly the state_lock).
The end-goal is to remove the indio_dev->mlock usage, and the simplest fix
would have been to just add another lock, which would not be a good idea on
the long-run.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lock can be extended a bit to protect other elements that are not
particular to just TX/RX. Another idea would have been to just add a new
`state_lock`, but that would mean 2 locks which would be redundant, and
probably cause more potential for dead-locks.
What will be done in the next patches, will be to add some unlocked
versions for read/write_reg functions.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for driving MPU9150 magnetometer (AK8975) from mpu.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MPU9150 is i2c only.
Update Kconfig to delete in description chips that are i2c or
spi only.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New device support
* ad5446
- Support the ad5600 DAC (id only needed).
* ad7292 ADC DAC etc
- New driver plus dt-bindings.
* veml6030 ambient light sensor
- New driver plus dt-bindings and sysfs docs.
Features
* mpu6050
- Explicit VDD control.
* stm32-adc
- Allow limiting of max clock frequency from devicetree to ensure it's
suitable for external circuitry.
yaml binding conversions
* ltc1660
* mcp3911
Fixes
* adis16480
- Fix wrong scale factors.
- Fix debugfs reg access by providing the callback.
* cros_ec_baro
- Fixing missing mask entry to make available sample frequencies visible
in sysfs.
* st_lsm6dsx
- Explicitly handle different ODR table sizes.
- Handle restrictions between slave ODR and accel ODR when
both are enabled.
- Allow ODR to be expressed more accurately by using miliHz.
* tools
- Fix an issue with parallel builds.
Cleanups and warning fixes
* adis16136, adis16400, adis16460, adis-lib
- Change some checks on return values to be for 0 rather than strictly
negative. Avoids some fiddly issues with the compiler concluding some
variables are initialized due to a mixture of error checks.
- Assign values only on success of 'read' operations - avoiding any
chance the compiler will falsly suggest they might be used uninitialized.
- Whitespace and simlar cleanups.
* aspeed adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* bcm-iproc-adc
- Stray semicolon removal.
* cc10001
- devm_platfom_ioremap_resource to reduce boilerplate.
* dln2-adc
- Reorganise the buffered mode setup and tear down. Part of moving towards
being able to refactor this area of the IIO core.
* hdc100x
- Reorganise the buffered mode setup and tear down.
* ingenic-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
* mt6577
- devm_platfom_ioremap_resource to reduce boilerplate.
* npcm
- devm_platfom_ioremap_resource to reduce boilerplate.
* rcar-gyroadc
- devm_platfom_ioremap_resource to reduce boilerplate.
* spear-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
-----BEGIN PGP SIGNATURE-----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=ckQz
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.5c' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of IIO new device support cleanups and fixes for the 5.5 cycle.
New device support
* ad5446
- Support the ad5600 DAC (id only needed).
* ad7292 ADC DAC etc
- New driver plus dt-bindings.
* veml6030 ambient light sensor
- New driver plus dt-bindings and sysfs docs.
Features
* mpu6050
- Explicit VDD control.
* stm32-adc
- Allow limiting of max clock frequency from devicetree to ensure it's
suitable for external circuitry.
yaml binding conversions
* ltc1660
* mcp3911
Fixes
* adis16480
- Fix wrong scale factors.
- Fix debugfs reg access by providing the callback.
* cros_ec_baro
- Fixing missing mask entry to make available sample frequencies visible
in sysfs.
* st_lsm6dsx
- Explicitly handle different ODR table sizes.
- Handle restrictions between slave ODR and accel ODR when
both are enabled.
- Allow ODR to be expressed more accurately by using miliHz.
* tools
- Fix an issue with parallel builds.
Cleanups and warning fixes
* adis16136, adis16400, adis16460, adis-lib
- Change some checks on return values to be for 0 rather than strictly
negative. Avoids some fiddly issues with the compiler concluding some
variables are initialized due to a mixture of error checks.
- Assign values only on success of 'read' operations - avoiding any
chance the compiler will falsly suggest they might be used uninitialized.
- Whitespace and simlar cleanups.
* aspeed adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* bcm-iproc-adc
- Stray semicolon removal.
* cc10001
- devm_platfom_ioremap_resource to reduce boilerplate.
* dln2-adc
- Reorganise the buffered mode setup and tear down. Part of moving towards
being able to refactor this area of the IIO core.
* hdc100x
- Reorganise the buffered mode setup and tear down.
* ingenic-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
* mt6577
- devm_platfom_ioremap_resource to reduce boilerplate.
* npcm
- devm_platfom_ioremap_resource to reduce boilerplate.
* rcar-gyroadc
- devm_platfom_ioremap_resource to reduce boilerplate.
* spear-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
* tag 'iio-for-5.5c' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (43 commits)
iio: adis16480: Add debugfs_reg_access entry
iio: adis16480: Fix scales factors
tools: iio: Correctly add make dependency for iio_utils
iio: adc: Add driver support for AD7292
dt-bindings: iio: adc: Add dt-schema for AD7292
dt-bindings: iio: adc: Migrate MCP3911 documentation to yaml
iio: imu: mpu6050: Add support for vdd-supply regulator
dt-bindings: iio: imu: mpu6050: add vdd-supply
iio: cros_ec_baro: set info_mask_shared_by_all_available field
iio: dac: ad5446: Add support for new AD5600 DAC
dt-bindings: iio: dac: Migrate LTC1660 documentation to yaml
iio: documentation: light: Add veml6030 sysfs documentation
dt-bindings: iio: light: add veml6030 ALS bindings
iio: light: add driver for veml6030 ambient light sensor
iio: imu: st_lsm6dsx: express odr in mHZ
iio: imu: st_lsm6dsx: fix ODR check in st_lsm6dsx_write_raw
iio: imu: st_lsm6dsx: explicitly define odr table size
iio: adc: stm32: allow to tune analog clock
dt-bindings: iio: stm32-adc: add max clock rate property
iio: dac: vf610: Use devm_platform_ioremap_resource
...
The driver is defining debugfs entries by calling
`adis16480_debugfs_init()`. However, those entries are attached to the
iio_dev debugfs entry which won't exist if no debugfs_reg_access
callback is provided.
Fixes: 2f3abe6cbb ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes the scales for the gyroscope, accelerometer and
barometer. The pressure scale was just wrong. For the others, the scale
factors were not taking into account that a 32bit word is being read
from the device.
Fixes: 7abad1063d ("iio: adis16480: Fix scale factors")
Fixes: 82e7a1b250 ("iio: imu: adis16480: Add support for ADIS1649x family of devices")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MPU6050 has two power supply pins: VDD and VLOGIC, but the
mpu6050 driver only supports enabling one of them at the moment.
In some cases, they may need to be enabled separately.
Add an additional "vdd-supply" that stays enabled for as long as
the driver is loaded. We cannot turn off the VDD regulator during
suspend as this would cause register settings (FSR, sampling rate, ...)
to be lost.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Express available frequencies in mHZ in order to support even
rational ODRs. This patch is need to fix an Android CTS failure
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since st_lsm6dsx i2c master controller relies on accel device as trigger
and slave devices can run at different ODRs we must select an accel_odr >=
slave_odr. Report real accel ODR in st_lsm6dsx_check_odr() in order to
properly set sensor frequency in st_lsm6dsx_write_raw and avoid to
report unsupported frequency
Fixes: 6ffb55e500 ("iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce odr_len in st_lsm6dsx_odr_table_entry data structure in order
to explicitly define odr table size and support devices with different
odr table map
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This was also caught by the `-Wmaybe-uninitialized` warning, which
(ironically as-is) it makes quite a lot of sense to do for this.
The code that actually calls this function will fail to copy on
the uninitialized value. Hence, patch does not need to go into stable.
Fixes: 78026a6fde ("iio:imu:adis: Add debugfs register access support")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This was found only after the whole thing with the inline functions, but
the compiler actually found something. The value of the `bias` (in
adis16480_get_calibbias()) should only be set if the read operation was
successful.
No actual known problem occurs as users of this function all
ultimately check the return value. Hence probably not stable material.
Fixes: 2f3abe6cbb ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a typical checkpatch warning. The change just renames the type of
the `freq` var to `unsigned int`.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is just a minor indentation/alignment fix for the default case of a
switch statement.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DSRX 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dsrx.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some chips have a fifo overflow bit issue where the bit is always
set. The result is that every data is dropped.
Change fifo overflow management by checking fifo count against
a maximum value.
Add fifo size in chip hardware set of values.
Fixes: f5057e7b2d ("iio: imu: inv_mpu6050: better fifo overflow handling")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
FXOS8700CQ is a small, low-power, 3-axis linear accelerometer and 3-axis
magnetometer combined into a single package. The device features a
selectable I2C or point-to-point SPI serial interface with 14-bit
accelerometer and 16-bit magnetometer ADC resolution along with
smart-embedded functions.
FXOS8700CQ has dynamically selectable accelerationfull-scale ranges of
±2 g/±4 g/±8 g and a fixed magnetic measurement range of ±1200 μT.
Output data rates (ODR) from 1.563 Hz to 800 Hz are selectable by the user
for each sensor. Interleaved magnetic and acceleration data is available
at ODR rates of up to 400 Hz. FXOS8700CQ is available in a plastic QFN
package and it is guaranteed to operate over the extended temperature
range of –40 °C to +85 °C.
TODO: Trigger and IRQ configuration support
Datasheet:
http://cache.freescale.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdf
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DS0 6-axis (acc + gyro) Mems sensor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix typos in gyro gain definitions for LSM9DS1 sensor
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On LSM6DSO/LSM6DSR/LSM6DSOX/ASM330LHH and ISH330DHCX
devices it is possible to trim the hardware timestamp
resolution through the FREQ_FINE[7:0] bits of the
INTERNAL_FREQ_FINE register, which contains the difference
in percentage of the effective ODR (and timestamp rate)
with respect to the typical value.
The formula for calculating the effective ODR reported
in the application notes has been linearized to the first
order to simplify the calculation (pls. see note on source
code).
This change may be useful in the outcome of CTS
tests regarding the SingleSensorTests and the
SensorTest#testSensorTimeStamps for high ODRs
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable drdy mask if available in order to mark invalid samples during
sensor bootstrap phase
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing wake-up register info for LSM6DSO/LSM6DSOX sensor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing kernel doc for st_lsm6dsx_hw data structure
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the possibility to enable/disable wakeup source through
st_sensors_platform_data and not only through device tree
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix following checkpatch warnings:
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_write_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event_config(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_write_event_config(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
WARNING: line over 80 characters
+ if (dev->of_node && of_property_read_bool(dev->of_node, "wakeup-source"))
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Always grub conf mutex in st_lsm6dsx_write_event_config since it can run
concurrently with FIFO configuration
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on st_lsm6dsx_update_bits_locked in st_lsm6dsx_write_event and
st_lsm6dsx_event_setup routines since they can run concurrently with
sensor hub configuration
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check if enable_reg of event_settings data structure is defined before
writing on it
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move bdu, boot and reset register definitions in hw_settings register
map since not all supported sensors (e.g lsm9ds1) rely on the same
definitions
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move active low and open drain register definitions in hw_settings
register map since not all supported sensors (e.g lsm9ds1) rely on the
same definitions
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Group irq related definition in irq_config structure in
st_lsm6dsx_settings. This is a preliminary patch to move
OpenDrain/Active low registers in st_lsm6dsx_settings.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check read_fifo pointer before using it since we can't assume it
is always set adding new sensors. This patch fixes the following crash:
irq 277: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.0-rc5-00322-g792b824-dirty #7
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[<c0112750>] (unwind_backtrace) from [<c010d018>] (show_stack+0x10/0x14)
[<c010d018>] (show_stack) from [<c0c2bfc8>] (dump_stack+0xd8/0x10c)
[<c0c2bfc8>] (dump_stack) from [<c01923fc>] (__report_bad_irq+0x24/0xc0)
[<c01923fc>] (__report_bad_irq) from [<c0192820>] (note_interrupt+0x27c/0x2dc)
[<c0192820>] (note_interrupt) from [<c018f174>] (handle_irq_event_percpu+0x54/0x7c)
[<c018f174>] (handle_irq_event_percpu) from [<c018f1d4>] (handle_irq_event+0x38/0x5c)
[<c018f1d4>] (handle_irq_event) from [<c0193664>] (handle_level_irq+0xc8/0x154)
[<c0193664>] (handle_level_irq) from [<c018df58>] (generic_handle_irq+0x20/0x34)
[<c018df58>] (generic_handle_irq) from [<c053c348>] (mxc_gpio_irq_handler+0xc4/0xf8)
[<c053c348>] (mxc_gpio_irq_handler) from [<c053c3e0>] (mx3_gpio_irq_handler+0x64/0xb8)
[<c053c3e0>] (mx3_gpio_irq_handler) from [<c018df58>] (generic_handle_irq+0x20/0x34)
[<c018df58>] (generic_handle_irq) from [<c018e550>] (__handle_domain_irq+0x64/0xe0)
[<c018e550>] (__handle_domain_irq) from [<c0529610>] (gic_handle_irq+0x4c/0xa0)
[<c0529610>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
Exception stack(0xc1301f10 to 0xc1301f58
1f00: 00000001 00000006 00000000 c130c340
1f20: c1300000 c1308928 00000001 c1308960 00000000 c12b9db0 c1308908 00000000
1f40: 00000000 c1301f60 c0182010 c0109508 20000013 ffffffff
[<c0101a70>] (__irq_svc) from [<c0109508>] (arch_cpu_idle+0x20/0x3c)
[<c0109508>] (arch_cpu_idle) from [<c015ed70>] (do_idle+0x1bc/0x2bc)
[<c015ed70>] (do_idle) from [<c015f204>] (cpu_startup_entry+0x18/0x1c)
[<c015f204>] (cpu_startup_entry) from [<c1200e68>] (start_kernel+0x440/0x504)
[<c1200e68>] (start_kernel) from [<00000000>] (0x0)
handlers:
[<62052c0d>] st_lsm6dsx_handler_irq threaded
[<f2004b92>] st_lsm6dsx_handler_thread
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Tested-by: Bobby Jones <rjones@gateworks.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on st_lsm6dsx_read_locked in st_lsm6dsx_report_motion_event since
it can run concurrently with sensor hub configuration. Move event
related code in st_lsm6dsx_report_motion_event
Fixes: 1aabad1fb5 ("iio: imu: st_lsm6dsx: add motion report function and call from interrupt")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since the logic for `spi_delay` struct + `spi_delay_exec()` has been copied
from the `cs_change_delay` logic, it's natural to make this delay, the
first user.
The `cs_change_delay` logic requires that the default remain 10 uS, in case
it is unspecified/unconfigured. So, there is some special handling needed
to do that.
The ADIS library is one of the few users of the new `cs_change_delay`
parameter for an spi_transfer.
The introduction of the `spi_delay` struct, requires that the users of of
`cs_change_delay` get an update. This change also updates the ADIS library.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-4-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It could happen that either `val` or `val2` [provided from userspace] is
negative. In that case the computed frequency could get a weird value.
Fix this by checking that neither of the 2 variables is negative, and check
that the computed result is not-zero.
Fixes: e4f9593901 ("iio: imu: adis16480 switch sampling frequency attr to core support")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c controller available in st_lsm6dsx series performs i2c slave
configuration using accel clock as trigger.
st_lsm6dsx_shub_wait_complete routine is used to wait the controller has
carried out the requested configuration. However if the accel sensor is not
enabled we should not use its configured odr to estimate a proper timeout
Fixes: c91c1c844e ("iio: imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode_burst, if adis->buffer allocation fails release
the adis->xfer.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode, if allocation for adis->buffer fails,
previously allocated adis->xfer needs to be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Report iio motion events to iio subsystem and filter motion events.
Wakeup will still be on all channels as it's not possible to do the filtering
in hw.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The interrupt source can come from multiple sources,
fifo and wake interrupts.
Enter interrupt thread to check which interrupt that has fired.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This add ways for the SoC to wake from accelerometer wake events.
In the suspend function we skip disabling the sensor if wakeup-source
and events are activated.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add event channels that controls the creation of motion events.
Tested on ISM330DLC
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This prepares the interrupt to be used for other stuff than
fifo reading + event readings.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Put read magnetometer data by mpu inside the fifo.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of driving MPU9250 magnetometer connected on i2c
auxiliary bus using the MPU i2c master.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add helper functions to use the i2c auxiliary bus with the MPU i2c
master block.
Support only register based chip, reading and 1 byte writing. These
will be useful for initializing magnetometers inside MPU9x50 chips.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the correct syntax *-y for declaring object files.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Disable i2c mux for supported 9xxx chips. This is a
pre-requesite for controling 9xxx magnetometer using the
i2c master of the chip.
Check in device-tree that there is no i2c-gate device declared
for ensuring backward compatibility with existing setups.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable clear on read feature for latched interrupts. This bit allows
immediately clearing the latched interrupts of an event detection upon
the read of the corresponding status register.
It must be set to 1 together with LIR.
This feature is available just on LSM6DS0/LSM6DSR/ASM330LHH
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable Latched interrupt by default for sensor events
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not allow configuring null sensor gain since it will force to 0
device outputs
Fixes: c8d4066c7246 ("iio: imu: st_lsm6dsx: remove invalid gain value for LSM9DS1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on IIO_G_TO_M_S_2 macro for LSM9DS1 accelerometer gain definitions
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Get rid of invalid sensitivity value for LSM9DS1 gyro sensor
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the latest version of datasheet the mask
for number of unread sensor data in FIFO_STATUS registers
has been extended to 10 bits
The devices involved are:
- LSM6DSO
- LSM6DSOX
- ASM330LHH
- LSM6DSR
- ISM330DHCX
Signed-off-by: mario tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The LSM9DS1's accelerometer / gyroscope unit and it's magnetometer (separately
supported in iio/magnetometer/st_magn*) are located on a separate i2c addresses
on the bus.
For the datasheet, see https://www.st.com/resource/en/datasheet/lsm9ds1.pdf
Treat it just like the LSM6* devices and, despite it's name, hook it up
to the st_lsm6dsx driver, using it's basic functionality.
accelerometer and gyroscope are not independently clocked. It runs at the gyro
frequencies if both are enabled, see chapter 7.12 of the datasheet.
We could have handled this as a single IIO device but we have split
it up to be more consistent with the other more flexible devices.
Despite supporting and testing the LSM9DS1, we call the gyro channels
iio_chan_spec struct "st_lsm6ds0_gyro_channels" because the register
description is equal. This suggests that supporting LSM6DS0 should be
trivial to do.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move some register definitions to the per-device array of struct
st_lsm6dsx_sensor_settings in order to simplify adding new sensor
devices to the driver.
Also, remove completely unused register definitions.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce update_fifo routine pointer in st_lsm6dsx_fifo_ops data
structure since we will need a different update FIFO configuration
callback adding support for lsm6ds0/lsm9ds1 imu device
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Caught via static-analysis checker:
```
drivers/iio/imu/adis16460.c
152 static int adis16460_set_freq(struct iio_dev *indio_dev, int val, int val2)
153 {
154 struct adis16460 *st = iio_priv(indio_dev);
155 unsigned int t;
^^^^^^^^^^^^^^
156
157 t = val * 1000 + val2 / 1000;
158 if (t <= 0)
^^^^^^
Unsigned is not less than zero.
```
The types of `val` && `val2` are obtained from the IIO `write_raw` hook, so
userspace can provide negative values, which can cause weird behavior after
conversion to unsigned.
This patch changes the sign of variable `t` so that -EINVAL will be
returned for negative values as well.
Fixes: db6ed4d23d ("iio: imu: Add support for the ADIS16460 IMU")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Note includes a merge from i3c tree to get support needed for stm_lsm6dsx driver
support for l3c devices. Done from immutable branch.
A counter subsystem patche in here as well.
Alongside the new device support (which is always good), Chuhong's work
on using devres managed APIs has cleaned up a number of drivers.
New device support
* adis16460
- New driver based on ADIS framework which needed addition of support
for cs_change_delay. Includes device tree binding.
* cros_ec
- Support fo the veyron-minnie which uses an older interface.
* lsm6dsx
- Support for LSM6DSTR-C gyro + magnetometer sensor (new IDs mainly)
- Support for ISM330DHCX acc + gyro sensor (extensive rework needed!)
* Maxim 5432
- New driver support MAX5432-MAX5435 family of potentiometers.
* noa1305
- New driver for this ON Semiconductor Ambient light sensor.
Features and cleanups
* tree wide
- Drop error prints after platform_get_irq as already prints errors
internally if any occur.
* docs
- Document mounting matrix.
- Fix a missing newline at end of file.
* ad2s1210
- Switch to device managed APIs for all of probe and drop explicit remove.
* ad7192
- Add of_device_id array to explicity handling DT bindings.
* ad7606
- Lots of rework leading to support for software configure modes in ad7616
parts.
- Debugfs register access support.
* am2315
- Switch to device managed APIs for all of probe and drop explicit remove.
* apds9960
- Typo in module description.
* cm36651
- Convert to i2c_new_dummy_device.
- Swithc to device managed APIs for all of probe adn drop explicit remove.
* cros_ec
- Calibscale support for accel, gyro and magnetometer.
- Tidy up some error codes to return the error from the stack rather than
-EIO.
- Determine protocol version.
- Add a sign vector to the core to fix sensor rotation if necessary.
Cannot just be done with mount matrix as already in use in many devices.
- Tidy up INFO_SCALE being in both the separate and shared lists.
- Drop a lot of dplicate code from the cros-ec-accel-legacy driver
and use the core provided code instead.
- Make frequency range available to userspace.
* counter / ftm-quaddec
- Switch to device managed APIs for all of probe adn drop explicit remove.
* hdc100x
- Switch to device managed APIs for all of probe and drop explicit remove.
* hi8435
- Use gpiod_set_value_cansleep as we don't care here and there is a
board out there where it needs to sleep.
- Switch to device managed APIs for all of probe and drop explict remove.
* hp03
- Convert to i2c_new_dummy_device.
* maxim thermocouple
- Switch to device managed APIs for all of probe and drop explicit remove.
* mmc35240
- Fix typo in constant naming.
* mpu6050
- Use devm_add_action_or_reset in place of explicit error handling.
- Make text in Kconfig more explicit about which parts are supported.
* mxc4005
- Switch to device managed APIs for all of probe and drop explicit remove.
* pms7003
- Convert device tree bindings to yaml.
- Add a MAINTAINERS entry
* sc27xx
- Introduce a local struct device *dev pointer to avoid lots of deref.
- Use devm_add_action_or_reset in place of explicit error handling.
* sca3000
- Typo fix in naming.
* si1145
- Switch to device managed APIs for all of probe and drop explicit remove.
* st_sensors
- Lots of rework to enable switch to regmap.
- Regmap conversion at the end.
- Tidy up some inconsistencies in buffer setup ops.
- Tidy up an oddity by dropping get_irq_data_ready function in favour
of direct access.
- Stop allocating buffer in buffer enable in favour of just embedding
a large enough constant size buffer in the iio_priv accessed structure.
* st_lsm6dsx
- l3c device support (LSM6DSO and LSM6DSR)
- tidy up irq return logic which was strangely written.
- fix up an ABI quirk where this driver used separate scale
attributes, even though they were always shared by type.
* stk33xx
- Device tree bindings include manufacturer ID.
* stm32-adc
- Add control for supply to analog switches including DT bindings.
* stm32 timer
- Drop the quadrature mode support. Believed there were no users so
take this opportunity to drop this unwanted ABI.
* tsl2772
- Switch to device mangage APIs for all of probe and drop explicit remove.
- Use regulator_bulk_* APIs to reduce repitition.
* veml6070
- Convert to i2c_new_dummy_device.
-----BEGIN PGP SIGNATURE-----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=aez5
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.4 cycle
Note includes a merge from i3c tree to get support needed for stm_lsm6dsx driver
support for l3c devices. Done from immutable branch.
A counter subsystem patche in here as well.
Alongside the new device support (which is always good), Chuhong's work
on using devres managed APIs has cleaned up a number of drivers.
New device support
* adis16460
- New driver based on ADIS framework which needed addition of support
for cs_change_delay. Includes device tree binding.
* cros_ec
- Support fo the veyron-minnie which uses an older interface.
* lsm6dsx
- Support for LSM6DSTR-C gyro + magnetometer sensor (new IDs mainly)
- Support for ISM330DHCX acc + gyro sensor (extensive rework needed!)
* Maxim 5432
- New driver support MAX5432-MAX5435 family of potentiometers.
* noa1305
- New driver for this ON Semiconductor Ambient light sensor.
Features and cleanups
* tree wide
- Drop error prints after platform_get_irq as already prints errors
internally if any occur.
* docs
- Document mounting matrix.
- Fix a missing newline at end of file.
* ad2s1210
- Switch to device managed APIs for all of probe and drop explicit remove.
* ad7192
- Add of_device_id array to explicity handling DT bindings.
* ad7606
- Lots of rework leading to support for software configure modes in ad7616
parts.
- Debugfs register access support.
* am2315
- Switch to device managed APIs for all of probe and drop explicit remove.
* apds9960
- Typo in module description.
* cm36651
- Convert to i2c_new_dummy_device.
- Swithc to device managed APIs for all of probe adn drop explicit remove.
* cros_ec
- Calibscale support for accel, gyro and magnetometer.
- Tidy up some error codes to return the error from the stack rather than
-EIO.
- Determine protocol version.
- Add a sign vector to the core to fix sensor rotation if necessary.
Cannot just be done with mount matrix as already in use in many devices.
- Tidy up INFO_SCALE being in both the separate and shared lists.
- Drop a lot of dplicate code from the cros-ec-accel-legacy driver
and use the core provided code instead.
- Make frequency range available to userspace.
* counter / ftm-quaddec
- Switch to device managed APIs for all of probe adn drop explicit remove.
* hdc100x
- Switch to device managed APIs for all of probe and drop explicit remove.
* hi8435
- Use gpiod_set_value_cansleep as we don't care here and there is a
board out there where it needs to sleep.
- Switch to device managed APIs for all of probe and drop explict remove.
* hp03
- Convert to i2c_new_dummy_device.
* maxim thermocouple
- Switch to device managed APIs for all of probe and drop explicit remove.
* mmc35240
- Fix typo in constant naming.
* mpu6050
- Use devm_add_action_or_reset in place of explicit error handling.
- Make text in Kconfig more explicit about which parts are supported.
* mxc4005
- Switch to device managed APIs for all of probe and drop explicit remove.
* pms7003
- Convert device tree bindings to yaml.
- Add a MAINTAINERS entry
* sc27xx
- Introduce a local struct device *dev pointer to avoid lots of deref.
- Use devm_add_action_or_reset in place of explicit error handling.
* sca3000
- Typo fix in naming.
* si1145
- Switch to device managed APIs for all of probe and drop explicit remove.
* st_sensors
- Lots of rework to enable switch to regmap.
- Regmap conversion at the end.
- Tidy up some inconsistencies in buffer setup ops.
- Tidy up an oddity by dropping get_irq_data_ready function in favour
of direct access.
- Stop allocating buffer in buffer enable in favour of just embedding
a large enough constant size buffer in the iio_priv accessed structure.
* st_lsm6dsx
- l3c device support (LSM6DSO and LSM6DSR)
- tidy up irq return logic which was strangely written.
- fix up an ABI quirk where this driver used separate scale
attributes, even though they were always shared by type.
* stk33xx
- Device tree bindings include manufacturer ID.
* stm32-adc
- Add control for supply to analog switches including DT bindings.
* stm32 timer
- Drop the quadrature mode support. Believed there were no users so
take this opportunity to drop this unwanted ABI.
* tsl2772
- Switch to device mangage APIs for all of probe and drop explicit remove.
- Use regulator_bulk_* APIs to reduce repitition.
* veml6070
- Convert to i2c_new_dummy_device.
* tag 'iio-for-5.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (84 commits)
iio: hi8435: Drop hi8435_remove() by using devres for remaining elements
iio: hi8435: Use gpiod_set_value_cansleep()
iio:st_sensors: remove buffer allocation at each buffer enable
iio: imu: inv_mpu6050: be more explicit on supported chips
iio: light: noa1305: Add support for NOA1305
dt-bindings: Add binding document for NOA1305
iio: remove get_irq_data_ready() function pointer and use IRQ number directly
iio: imu: st_lsm6dsx: make IIO_CHAN_INFO_SCALE shared by type
iio: tsl2772: Use regulator_bulk_() APIs
iio: tsl2772: Use devm_iio_device_register
iio: tsl2772: Use devm_add_action_or_reset for tsl2772_chip_off
iio: tsl2772: Use devm_add_action_or_reset
iio: Remove dev_err() usage after platform_get_irq()
iio: light: si1145: Use device-managed APIs
iio:pressure: preenable/postenable/predisable fixup for ST press buffer
iio:magn: preenable/postenable/predisable fixup for ST magn buffer
iio:gyro: preenable/postenable/predisable fixup for ST gyro buffer
iio:accel: preenable/postenable/predisable fixup for ST accel buffer
dt-bindings: iio: imu: st_lsm6dsx: add ism330dhcx device bindings
iio: imu: st_lsm6dsx: add support to ISM330DHCX
...
Since every chip has a different whoami, we are not supporting all
existing variant of all chips. Add an explicit supported chips
list in Kconfig description.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
in_accel_x_scale, in_accel_y_scale and in_accel_z_scale are always
the same. The scale is still defined to be in "info_mask_separate".
Userspace (iio-sensor-proxy and others) is not used to that and only
looks for "in_accel_scale" for the scaling factor to apply.
Change IIO_CHAN_INFO_SCALE from being separate in all channel to be
shared by type.
This removes in_accel_x_scale, in_accel_y_scale and in_accel_z_scale and
makes available in_accel_scale.
This is an ABI change, but hopefully in the 'no one will notice'
category. The cleanup in interface is worth the small risk that
there is a custom script out there somewhere that this will break.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM ISM330DHCX 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/ism330dhcx.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move IIO channel definitions in st_lsm6dsx_sensor_settings in order to
support sensors with different channels maps.
This is a preliminary patch to add support for LSM9DS1 sensor to
st_lsm6dsx driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove output register definition and inline register value since
they are used only for iio channel definition. This is a preliminary
patch to add support for LSM9DS1 sensor to st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move fs_table in st_lsm6dsx_sensor_settings in order to support
sensors with different gain maps. This is a preliminary patch to add
support for LSM9DS1 sensor to st_lsm6dsx driver
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move sensor odr table in st_lsm6dsx_sensor_settings in order to support
sensors with different odr maps. This is a preliminary patch to add
support for LSM9DS1 sensor to st_lsm6dsx driver
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
No need for using reverse logic in the irq return,
fix this by flip things around.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For today the st_lsm6dsx driver support LSM6DSO and LSM6DSR sensor only in
spi and i2c mode.
The LSM6DSO and LSM6DSR are also i3c capable so let's give i3c support to
them.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS16460 device is a complete inertial system that includes a triaxial
gyroscope and a triaxial accelerometer. It's more simplified design than
that of the ADIS16480, and does not offer the triaxial magnetometers &
pressure sensors. It does also have a temperature sensor (like the
ADIS16480).
Since it is part of the ADIS16XXX family, it re-uses parts of the ADIS
library.
Naturally, the register map is different and much more simplified than the
ADIS16480 subfamily, so it cannot be integrated into that driver. A major
difference is that the registers are not paged.
One thing that is particularly special about it, is that it requires a
higher delay between CS changes (i.e. when CS goes up, the spec recommends
that it be brought down after a minimum of 16 uS).
Other ADIS chips require (via spec) a minimum of 2 uS between CS changes.
The kernel's 10 uS default should be fine for those other chips; they
haven't been tested with lower CS change delays yet.
Datasheet:
https://www.analog.com/media/en/technical-documentation/data-sheets/adis16460.pdf
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS16460 requires a higher delay before the next transfer. Since the
SPI framework supports configuring the delay before the next transfer, this
driver will become the first user of it.
The support for this functionality in ADIS16460 requires an addition to the
ADIS lib to support the `cs_change_delay` functionality from the SPI
subsystem.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DS3TR-C 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6ds3tr-c.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver only supports 3-axis gyro and/or 3-axis accel.
For icm20602, temp data is mandatory for all configurations.
Fix all single and double axis configurations (almost never used) and more
importantly fix 3-axis gyro and 6-axis accel+gyro buffer on icm20602 when
temp data is not enabled.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Fixes: 1615fe41a1 ("iio: imu: mpu6050: Fix FIFO layout for ICM20602")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A few bits for the counters subsystem mixed in here as well.
There are some late breaking fixes as well, which aren't so urgent
they can't wait for the merge window.
New Device Support
* adf4371
- New driver + bindings.
- Support the adf4372 PLL. Mostly ID and bindings.
* ad8366 (note includes rework of driver needed to allow support for these).
- Support the ADL5240 variable gain amplifier (VGA).
- Support the ADA4961 digital gain amplifier (DGA).
* dps310
- New driver, in several parts from different authors for this temp
and pressure sensor.
- Includes errata workaround for a temperature reading issue.
* stk3310
- Support the stk3335, mostly ID.
Features and cleanups
* core
- drop error handling on debugfs registration.
- harden by making sure we don't overrun iio_chan_info_postfix.
* docs
- convert remaining docs to rst. At somepoint we'll fit these few
into the main IIO docs.
- improve sampling_frequency_available docs but explaining the
range form.
* ad_sigma_delta
- Drop a pointless goto.
* ad2s1210
- Drop pointless platform data null check seeing as we don't actually
use platform data anymore.
* ad7124
- Relax limitation on channel numbers to allow pseudo different channels.
- Support control of whether the input is buffered via DT.
- Use dynamic allocation for channel configuration to make it easier
to support new devices.
- YAML binding conversion.
* ad7150
- Comment tidy up.
- Consistent and simple if (ret) handling of i2c errors.
- FIELD_GET and GENMASK.
- Ternary rather than !!(condition) for readability.
- Use macros to avoid repetition of channel definitions.
* ad7606
- Add software channel config (rather that pin controlled)
- Refactor to simplify addition of new part in future.
* ad7746
- of_deivce_id table.
* ad7780
- MAINTAINERS entry
- YAML DT bindings.
* ad8366
- Stop using core mlock in favour of well scoped local lock.
- SPDX + copyright date update.
* ad9834
- of_device_id table
* adf4371
- Add support for output stage muting before lock on has occured.
* adis library
- MAINTAINERS entry to reflect that this now Alexandru's problem ;)
* adis162xx:
- Fix a slightly incorrect set of comments and print statements on
minimum supported voltage.
* adis16203
- of_device_id table.
* adis16240
- Add of_device_id table (in two parts as first patch only used it for
MODULE_DEVICE_TABLE.)
* adt7316-spi
- of_device_id table
* adxl372
- YAML DT binding conversion.
- Cleanup use of buffer callback functions (precursor to core rework).
* bh1710
- Simplify getting the i2c adapter from the client.
* dht11
- Mote to newer GPIO consumer interface.
* kxcjk-1013.c
- Add binding for sensor in display of some ultrabooks after userspace
tools updated for it not be a problem to report two similar sensors.
* imx7d
- drop unused variables.
- white space
- define instead of variable for clock frequency that is fixed.
- drop pointless error message.
* messon_saradc
- SPDX
* sps30
- MAINTAINERS entry
- YAML binding conversion.
* st_accel
- Tidy up ordering in various buffer related callbacks. This is
part of a long running effort to simplify the core code.
* stm32-dfsdm:
- Manage the resolution cleanly in triggerd modes.
- Add fast mode support which allows more flexible filter choices.
- Add a comment on the reason for a 16 bit record when technically
not 'required'.
* st_lsm6dsx
- Embed device name in the sensor_settings struct as i3c doesn't
have a convenient name field to use for this.
* xilinx-adc
- Relax constraints on supported platforms to reflect that this
can used with FPGAs on PCIe cards and hence many architectures.
* counters/ftm-quaddec
- Fix some formatting io MODULE_AUTHOR
- MAINTAINERS entry
Fixes
* tools
- fix incorrect handling of 32 bit channels.
* sca3000
- Potential endian bug that is unlikely to bite anyone (be64 host
seems unlikely for this old part).
* stm32-adc
- Add vdda-supply. On some boards it needs to be turned on to supply
the ADC. DT bindings included.
* stm32-dfsdm
- Fix output resolution to work with filter orders other than 3.
- Fix output datatype as it's signed and previously claimed not to be.
-----BEGIN PGP SIGNATURE-----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=a3vh
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO device support, features, cleanups and minor fixes for 5.3.
A few bits for the counters subsystem mixed in here as well.
There are some late breaking fixes as well, which aren't so urgent
they can't wait for the merge window.
New Device Support
* adf4371
- New driver + bindings.
- Support the adf4372 PLL. Mostly ID and bindings.
* ad8366 (note includes rework of driver needed to allow support for these).
- Support the ADL5240 variable gain amplifier (VGA).
- Support the ADA4961 digital gain amplifier (DGA).
* dps310
- New driver, in several parts from different authors for this temp
and pressure sensor.
- Includes errata workaround for a temperature reading issue.
* stk3310
- Support the stk3335, mostly ID.
Features and cleanups
* core
- drop error handling on debugfs registration.
- harden by making sure we don't overrun iio_chan_info_postfix.
* docs
- convert remaining docs to rst. At somepoint we'll fit these few
into the main IIO docs.
- improve sampling_frequency_available docs but explaining the
range form.
* ad_sigma_delta
- Drop a pointless goto.
* ad2s1210
- Drop pointless platform data null check seeing as we don't actually
use platform data anymore.
* ad7124
- Relax limitation on channel numbers to allow pseudo different channels.
- Support control of whether the input is buffered via DT.
- Use dynamic allocation for channel configuration to make it easier
to support new devices.
- YAML binding conversion.
* ad7150
- Comment tidy up.
- Consistent and simple if (ret) handling of i2c errors.
- FIELD_GET and GENMASK.
- Ternary rather than !!(condition) for readability.
- Use macros to avoid repetition of channel definitions.
* ad7606
- Add software channel config (rather that pin controlled)
- Refactor to simplify addition of new part in future.
* ad7746
- of_deivce_id table.
* ad7780
- MAINTAINERS entry
- YAML DT bindings.
* ad8366
- Stop using core mlock in favour of well scoped local lock.
- SPDX + copyright date update.
* ad9834
- of_device_id table
* adf4371
- Add support for output stage muting before lock on has occured.
* adis library
- MAINTAINERS entry to reflect that this now Alexandru's problem ;)
* adis162xx:
- Fix a slightly incorrect set of comments and print statements on
minimum supported voltage.
* adis16203
- of_device_id table.
* adis16240
- Add of_device_id table (in two parts as first patch only used it for
MODULE_DEVICE_TABLE.)
* adt7316-spi
- of_device_id table
* adxl372
- YAML DT binding conversion.
- Cleanup use of buffer callback functions (precursor to core rework).
* bh1710
- Simplify getting the i2c adapter from the client.
* dht11
- Mote to newer GPIO consumer interface.
* kxcjk-1013.c
- Add binding for sensor in display of some ultrabooks after userspace
tools updated for it not be a problem to report two similar sensors.
* imx7d
- drop unused variables.
- white space
- define instead of variable for clock frequency that is fixed.
- drop pointless error message.
* messon_saradc
- SPDX
* sps30
- MAINTAINERS entry
- YAML binding conversion.
* st_accel
- Tidy up ordering in various buffer related callbacks. This is
part of a long running effort to simplify the core code.
* stm32-dfsdm:
- Manage the resolution cleanly in triggerd modes.
- Add fast mode support which allows more flexible filter choices.
- Add a comment on the reason for a 16 bit record when technically
not 'required'.
* st_lsm6dsx
- Embed device name in the sensor_settings struct as i3c doesn't
have a convenient name field to use for this.
* xilinx-adc
- Relax constraints on supported platforms to reflect that this
can used with FPGAs on PCIe cards and hence many architectures.
* counters/ftm-quaddec
- Fix some formatting io MODULE_AUTHOR
- MAINTAINERS entry
Fixes
* tools
- fix incorrect handling of 32 bit channels.
* sca3000
- Potential endian bug that is unlikely to bite anyone (be64 host
seems unlikely for this old part).
* stm32-adc
- Add vdda-supply. On some boards it needs to be turned on to supply
the ADC. DT bindings included.
* stm32-dfsdm
- Fix output resolution to work with filter orders other than 3.
- Fix output datatype as it's signed and previously claimed not to be.
* tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (68 commits)
iio: iio-utils: Fix possible incorrect mask calculation
iio: frequency: adf4371: Add support for output stage mute
dt-bindings: iio: frequency: Add ADF4372 PLL documentation
iio: frequency: adf4371: Add support for ADF4372 PLL
dt-bindings: iio: adc: Add buffered input property
Convert AD7124 bindings documentation to YAML format.
iio: adc: ad7124: Shift to dynamic allocation for channel configuration
iio: adc: ad7124: Add buffered input support
iio: adc: ad7124: Remove input number limitation
MAINTAINERS: add ADIS IMU driver library entry
iio: adis162xx: fix low-power docs & reports
counter/ftm-quaddec: Add missing '>' in MODULE_AUTHOR
iio: core: no need to check return value of debugfs_create functions
docs: iio: convert to ReST
iio: adc: stm32-adc: add missing vdda-supply
dt-bindings: iio: adc: stm32: add missing vdda supply
iio: adc: stm32-dfsdm: add comment for 16 bits record
iio: adc: stm32-dfsdm: add fast mode support
iio: adc: stm32-dfsdm: manage data resolution in trigger mode
iio: adc: stm32-dfsdm: fix data type
...
Here are some small driver bugfixes for some staging/iio/counter
drivers.
Staging and IIO have been lumped together for a while, as those
subsystems cross the areas a log, and counter is used by IIO, so that's
why they are all in one pull request here.
These are small fixes for reported issues in some iio drivers, the erofs
filesystem, and a build issue for counter code.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyM7w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymBUwCYn7LKiishfnvx8PpGF1lGHNmtYACgrNoAWKRZ
PUlOWXEbtD7NAPtqn3c=
=tXAQ
-----END PGP SIGNATURE-----
Merge tag 'staging-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO/counter fixes from Greg KH:
"Here are some small driver bugfixes for some staging/iio/counter
drivers.
Staging and IIO have been lumped together for a while, as those
subsystems cross the areas a log, and counter is used by IIO, so
that's why they are all in one pull request here.
These are small fixes for reported issues in some iio drivers, the
erofs filesystem, and a build issue for counter code.
All have been in linux-next with no reported issues"
* tag 'staging-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: erofs: add requirements field in superblock
counter/ftm-quaddec: Add missing dependencies in Kconfig
staging: iio: adt7316: Fix build errors when GPIOLIB is not set
iio: temperature: mlx90632 Relax the compatibility check
iio: imu: st_lsm6dsx: fix PM support for st_lsm6dsx i2c controller
staging:iio:ad7150: fix threshold mode config bit
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ad7150
- sense of bit for controlling adaptive vs fixed threshold was flipped.
* adt7316
- Fix a build issue due to wrong headers for gpio usage.
* lsm6dsx
- correctly suspend / resume i2c slaves when the host goes to sleep.
* mlx90632
- relax a compatability check to allow for newer devices.
Also one counters fix
* counter/ftm-quaddec
- missing dependencies in Kconfig.
-----BEGIN PGP SIGNATURE-----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=2i3G
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 5.2 cycle.
* ad7150
- sense of bit for controlling adaptive vs fixed threshold was flipped.
* adt7316
- Fix a build issue due to wrong headers for gpio usage.
* lsm6dsx
- correctly suspend / resume i2c slaves when the host goes to sleep.
* mlx90632
- relax a compatability check to allow for newer devices.
Also one counters fix
* counter/ftm-quaddec
- missing dependencies in Kconfig.
* tag 'iio-fixes-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
counter/ftm-quaddec: Add missing dependencies in Kconfig
staging: iio: adt7316: Fix build errors when GPIOLIB is not set
iio: temperature: mlx90632 Relax the compatibility check
iio: imu: st_lsm6dsx: fix PM support for st_lsm6dsx i2c controller
staging:iio:ad7150: fix threshold mode config bit
Introduce sensor name in st_lsm6dsx_sensor_settings table. This is
a preliminary patch to add I3C support to st_lsm6dsx since i3c_device_id
data structure does not contain a name field
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on 1 normalized pattern(s):
this file is subject to the terms and conditions of version 2 of the
gnu general public license see the file copying in the main
directory of this archive for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 55 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.108941081@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Here are some Staging and IIO driver fixes to resolve some reported
problems for 5.2-rc3.
Nothing major here, just some tiny changes, full details are in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCE/w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylLwQCdFRL6v7IHdGYQ6cAk/tjOcyYY0IEAoNRAdZU7
n/JfHbtKvS7VpYzPzRvO
=LjTj
-----END PGP SIGNATURE-----
Merge tag 'staging-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some Staging and IIO driver fixes to resolve some reported
problems for 5.2-rc3.
Nothing major here, just some tiny changes, full details are in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'staging-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: kpc2000: Add dependency on MFD_CORE to kconfig symbol 'KPC2000'
staging: wilc1000: Fix some double unlock bugs in wilc_wlan_cleanup()
staging: vc04_services: prevent integer overflow in create_pagelist()
Staging: vc04_services: Fix a couple error codes
staging: wlan-ng: fix adapter initialization failure
staging: kpc2000: double unlock in error handling in kpc_dma_transfer()
staging: kpc2000: Fix build error without CONFIG_UIO
staging: kpc2000: fix build error on xtensa
staging: erofs: set sb->s_root to NULL when failing from __getname()
iio: adc: ti-ads8688: fix timestamp is not updated in buffer
iio: dac: ds4422/ds4424 fix chip verification
iio: imu: mpu6050: Fix FIFO layout for ICM20602
iio: adc: ads124: avoid buffer overflow
iio: adc: modify NPCM ADC read reference voltage
Based on 1 normalized pattern(s):
licensed under the gpl 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 82 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.150836982@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly suspend/resume i2c slaves connected to st_lsm6dsx master
controller if the CPU goes in suspended state
Fixes: c91c1c844e ("imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ads124
- Avoid a buffer overrun when setting an array to 0.
* ads8688
- Don't use the pollfunc timestamp as it isn't set and would be wrong
anyway for a device that does sampling on demand.
* ds4422
- Fix masking on register used for chip verification. Wrong address
was being read.
* mpu6050
- Fix the fifo layout for ICM20602 to avoid underreading and hence failure
to move on to the next record in the fifo.
* NPCM ADC
- Make sure there is actually a valid regulator before reading its voltage.
-----BEGIN PGP SIGNATURE-----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=nq1b
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus:
Jonathan writes:
First set of IIO fixes for the 5.2 cycle.
* ads124
- Avoid a buffer overrun when setting an array to 0.
* ads8688
- Don't use the pollfunc timestamp as it isn't set and would be wrong
anyway for a device that does sampling on demand.
* ds4422
- Fix masking on register used for chip verification. Wrong address
was being read.
* mpu6050
- Fix the fifo layout for ICM20602 to avoid underreading and hence failure
to move on to the next record in the fifo.
* NPCM ADC
- Make sure there is actually a valid regulator before reading its voltage.
* tag 'iio-fixes-for-5.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: ti-ads8688: fix timestamp is not updated in buffer
iio: dac: ds4422/ds4424 fix chip verification
iio: imu: mpu6050: Fix FIFO layout for ICM20602
iio: adc: ads124: avoid buffer overflow
iio: adc: modify NPCM ADC read reference voltage
As it has been already done for other st sensors in 'commit 9049531c91
("iio: accel: st_accel: inline per-sensor data")', get rid of some
defines and just open code the values into the appropriate struct
elements since the semantic meaning is inherent in the name of the
C99-addressable fields and there is no reason to duplicate the code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c: In function 'st_lsm6dsx_read_tagged_fifo':
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c:520:41: warning:
variable 'gyro_sensor' set but not used [-Wunused-but-set-variable]
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c:520:28: warning:
variable 'acc_sensor' set but not used [-Wunused-but-set-variable]
They are not used since commit 14c7c6e1a8 ("iio: imu: st_lsm6dsx: add
st_lsm6dsx_push_tagged_data routine")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MPU6050 driver has recently gained support for the
ICM20602 IMU, which is very similar to MPU6xxx. However,
the ICM20602's FIFO data specifically includes temperature
readings, which were not present on MPU6xxx parts. As a
result, the driver will under-read the ICM20602's FIFO
register, causing the same (partial) sample to be returned
for all reads, until the FIFO overflows.
Fix this by adding a table of scan elements specifically
for the ICM20602, which takes the extra temperature data
into consideration.
While we're at it, fix the temperature offset and scaling
on ICM20602, since it uses different scale/offset constants
than the rest of the MPU6xxx devices.
Signed-off-by: Steve Moskovchenko <stevemo@skydio.com>
Fixes: 22904bdff9 ("iio: imu: mpu6050: Add support for the ICM 20602 IMU")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DSR 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dsr.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Final part of the re-organization. Move the `adis16400.h` into
`adis16400.c` since it no longer needs to be shared among other files.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change does a simple 1-to-1 rename of the adis16400_core.c file. Now
that the `adis16400_buffer.c` file was removed, everything can be moved
into a single driver file.
But first, this rename.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
