Add a "scope" parameter to ip_route_output() so that callers don't have
to override the tos parameter with the RTO_ONLINK flag if they want a
local scope.
This will allow converting flowi4_tos to dscp_t in the future, thus
allowing static analysers to flag invalid interactions between
"tos" (the DSCP bits) and ECN.
Only three users ask for local scope (bonding, arp and atm). The others
continue to use RT_SCOPE_UNIVERSE. While there, add a comment to warn
users about the limitations of ip_route_output().
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com> # infiniband
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of stacked devices, to help propagate the down
link state from the parent/root device (to this leaf device),
handle NETDEV_DOWN event like it is done now for NETDEV_UP.
In the below example, ens5 is the host interface which is the
parent of the ipvlan interface eth0 in the container.
Host:
[root@gkn-podman-x64 ~]# ip link set ens5 down
[root@gkn-podman-x64 ~]# ip -d link show dev ens5
3: ens5: <BROADCAST,MULTICAST> mtu 9000 qdisc mq state DOWN
...
[root@gkn-podman-x64 ~]#
Container:
[root@testnode-ol8 /]# ip -d link show dev eth0
2: eth0@if3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 state UNKNOWN
...
ipvlan mode l2 bridge
...
[root@testnode-ol8 /]#
eth0's state continues to show up as UP even though ens5 is now DOWN.
For macvlan the handling of NETDEV_DOWN event was added in
commit 80fd2d6ca5 ("macvlan: Change status when lower device goes down").
Reported-by: Gia-Khanh Nguyen <gia-khanh.nguyen@oracle.com>
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the code is correct, the following line
copy_from_sockptr(&req_u.req, optval, len));
triggers this warning :
memcpy: detected field-spanning write (size 28) of single field "dst" at include/linux/sockptr.h:49 (size 16)
Refactor the code to be more explicit.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for
those drivers requiring them. For the DEFXX driver the use of I/O
ports is optional and we only need to fence specific code paths. It also
turns out that with HAS_IOPORT handled explicitly HAMRADIO does not need
the !S390 dependency and successfully builds the bpqether driver.
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthieu Baerts says:
====================
selftests: mptcp: cleanups and 'ip mptcp' support
Here are some patches from Geliang, doing different cleanups, and
supporting 'ip mptcp' in more MPTCP selftests.
Patch 1 checks that TC is available in selftests requiring it.
Patch 2 adds 'ms' units in TC commands, to avoid confusions.
Patches 3-9 are some prerequisites for patch 10: some export code from
mptcp_join.sh to mptcp_lib.sh, to be re-used in pm_netlink.sh,
mptcp_sockopt.sh and simult_flows.sh ; and others add helpers to
pm_netlink.sh to easily support both 'ip mptcp' and 'pm_nl_ctl' tools to
interact with the in-kernel MPTCP path-manager.
Patch 10 adds a '-i' parameter in mptcp_sockopt.sh, pm_netlink.sh, and
simult_flows.sh to use 'ip mptcp' tool instead of 'pm_nl_ctl'.
Patch 11 fixes some ShellCheck warnings in pm_netlink.sh, in order to
drop a ShellCheck's 'disable' instruction.
====================
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now there are only a few of variables are not using double quotes.
Modifying them, then "shellcheck disable=SC2086" can be dropped.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds '-i' option for mptcp_sockopt.sh, pm_netlink.sh, and
simult_flows.sh, to use 'ip mptcp' command in the tests instead of
'pm_nl_ctl'. Update usage() correspondingly.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use those newly added pm_nl endpoint ops helpers to replace all 'pm_nl_ctl'
commands with 'limits', 'add', 'del', 'flush', 'show' and 'set' arguments
in scripts mptcp_sockopt.sh and simult_flows.sh.
In pm_netlink.sh, add wrappers of there helpers to make the function names
shorter. Then use the wrappers to replace all 'pm_nl_ctl' commands.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports six endpoint operation helpers with pm_nl_ prefix,
pm_nl_set_limits(), pm_nl_add_endpoint(), pm_nl_del_endpoint(),
pm_nl_flush_endpoint(), pm_nl_show_endpoints() and pm_nl_change_endpoint()
into mptcp_lib.sh as public functions, and renamed each of them with a
mptcp_lib_ prefix. Then these old pm_nl_ prefix helpers in mptcp_join.sh
can be wrappers of mptcp_lib_ prefix ones.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses 'case' statements to simplify pm_nl_add_endpoint() and
pm_nl_check_endpoint(). And simplify pm_nl_check_endpoint() with
check_output() helper. Also update pm_nl_del_endpoint() to avoid the
'double quote' shellcheck warning.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The output formats of 'ip mptcp' commands are much different from that
of 'pm_nl_ctl' commands.
A new 'change_address' helper is added here, to change the flag of an
address. This is a bit similar to mptcp_join.sh's pm_nl_change_endpoint().
Usage:
Address ID - pm_nl_change_endpoint $ns id $id $flags
IP address - change_address $ns $addr $flags
Use this new helper in pm_netlink.sh to replace all 'pm_nl_ctl set'
commands.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The output formats of 'ip mptcp' commands are much different from that
of 'pm_nl_ctl' commands.
This patch adds a new helper format_endpoints() to format the outputs of
'ip mptcp' and 'pm_nl_ctl' with 'endpoints' arguments to hide these
differences.
A new helper named get_endpoint() has also been added to show a specific
endpoint identified by the given address ID, similar to mptcp_join.sh's
pm_nl_show_endpoints() helper, but showing all entries.
Use these two helpers in mptcp_join.sh and pm_netlink.sh to replace all
'pm_nl_ctl get' commands and outputs of 'pm_nl_ctl dump/get'.
Suggested-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The output format of 'ip mptcp limits' command is much different from
that of 'pm_nl_ctl limits' command.
This patch adds format_limits() helper to format the outputs of these
two commands to hide the difference. get_limits() has been added to show
the limits.
Use these two helpers in pm_netlink.sh to replace all 'pm_nl_ctl limits'
commands and outputs.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports ip_mptcp into mptcp_lib.sh as a public variable,
named MPTCP_LIB_IP_MPTCP. Add a helper mptcp_lib_set_ip_mptcp() to set
it, and a helper mptcp_lib_is_ip_mptcp() to test whether it is set. Use
these two helpers in mptcp_join.sh.
This patch is prepared for coming commits.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
'delay 1' in tc-netem is confusing, not sure if it's a delay of 1 second or
1 millisecond. This patch explicitly adds millisecond units to make these
commands clearer.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc are used in some test scripts: mptcp_connect.sh, mptcp_join.sh and
simult_flows.sh. It makes sense to check if tc is installed before running
these scripts, just like other tools. So this patch add 'tc' check for
mptcp_lib_check_tools(), and check it in these test scripts.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tp->recvmsg_inq is used from tcp recvmsg() thus should
be in tcp_sock_read_rx group.
tp->tcp_clock_cache and tp->tcp_mstamp are written
both in rx and tx paths, thus are better placed
in tcp_sock_write_txrx group.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mac address can not be read from the device registers or the
devicetree, a random address is generated, but this was already done from
usbnet_probe, so it is not necessary to call eth_hw_addr_random from here
again to generate another random address.
Indeed, when reset was also executed from bind, generate another random mac
address invalidated the check from usbnet_probe to configure if the assigned
mac address for the interface was random or not, because it is comparing
with the initial generated random address. Now, with only a reset from open
operation, it is just a harmless simplification.
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Arnd comments:
"The memcpy() in the ip_tunnel_info_opts_set() causes
a string.h fortification warning, with at least gcc-13:
In function 'fortify_memcpy_chk',
inlined from 'ip_tunnel_info_opts_set' at include/net/ip_tunnels.h:619:3,
inlined from 'pfcp_encap_recv' at drivers/net/pfcp.c:84:2:
include/linux/fortify-string.h:553:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
553 | __write_overflow_field(p_size_field, size);"
It is a false-positivie caused by ambiguity of the union.
However, as Arnd noticed, copying here is unescessary. The code can be
simplified to avoid calling ip_tunnel_info_opts_set(), which is doing
copying, setting flags and options_len.
Set correct flags and options_len directly on tun_info.
Fixes: 6dd514f481 ("pfcp: always set pfcp metadata")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Closes: https://lore.kernel.org/netdev/701f8f93-f5fb-408b-822a-37a1d5c424ba@app.fastmail.com/
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
selftests: net: groundwork for YNL-based tests
Currently the options for writing networking tests are C, bash or
some mix of the two. YAML/Netlink gives us the ability to easily
interface with Netlink in higher level laguages. In particular,
there is a Python library already available in tree, under tools/net.
Add the scaffolding which allows writing tests using this library.
The "scaffolding" is needed because the library lives under
tools/net and uses YAML files from under Documentation/.
So we need a small amount of glue code to find those things
and add them to TEST_FILES.
This series adds both a basic SW sanity test and driver
test which can be run against netdevsim or a real device.
When I develop core code I usually test with netdevsim,
then a real device, and then a backport to Meta's kernel.
Because of the lack of integration, until now I had
to throw away the (YNL-based) test script and netdevsim code.
Running tests in tree directly:
$ ./tools/testing/selftests/net/nl_netdev.py
KTAP version 1
1..2
ok 1 nl_netdev.empty_check
ok 2 nl_netdev.lo_check
# Totals: pass:2 fail:0 xfail:0 xpass:0 skip:0 error:0
in tree via make:
$ make -C tools/testing/selftests/ TARGETS=net \
TEST_PROGS=nl_netdev.py TEST_GEN_PROGS="" run_tests
[ ... ]
and installed externally, all seem to work:
$ make -C tools/testing/selftests/ TARGETS=net \
install INSTALL_PATH=/tmp/ksft-net
$ /tmp/ksft-net/run_kselftest.sh -t net:nl_netdev.py
[ ... ]
For driver tests I followed the lead of net/forwarding and
get the device name from env and/or a config file.
v3:
- fix up netdevsim C
- various small nits in other patches (see changelog in patches)
v2: https://lore.kernel.org/all/20240403023426.1762996-1-kuba@kernel.org/
- don't add to TARGETS, create a deperate variable with deps
- support and use with
- support and use passing arguments to tests
v1: https://lore.kernel.org/all/20240402010520.1209517-1-kuba@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a very simple test to make sure drivers report expected
stats. Drivers which implement FEC or pause configuration
should report relevant stats. Qstats must be reported,
at least packet and byte counts, and they must match
total device stats.
Tested with netdevsim, bnxt, in-tree and installed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add drivers/net as a target for mixed-use tests.
The setup is expected to work similarly to the forwarding tests.
Since we only need one interface (unlike forwarding tests)
read the target device name from NETIF. If not present we'll
try to run the test against netdevsim.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Real devices should implement qstats. Devices which support
pause or FEC configuration should also report the relevant stats.
nsim was missing FEC stats completely, some of the qstats
and pause stats required toggling a debugfs knob.
Note that the tests which used pause always initialize the setting
so they shouldn't be affected by the different starting value.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a trivial test using YNL.
$ ./tools/testing/selftests/net/nl_netdev.py
KTAP version 1
1..2
ok 1 nl_netdev.empty_check
ok 2 nl_netdev.lo_check
Instantiate the family once, it takes longer than the test itself.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add glue code for accessing the YNL library which lives under
tools/net and YAML spec files from under Documentation/.
Automatically figure out if tests are run in tree or not.
Since we'll want to use this library both from net and
drivers/net test targets make the library a target as well,
and automatically include it when net or drivers/net are
included. Making net/lib a target ensures that we end up
with only one copy of it, and saves us some path guessing.
Add a tiny bit of formatting support to be able to output KTAP
from the start.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- prefer kfree_rcu() over call_rcu() with free-only callbacks,
by Dmitry Antipov
- bypass empty buckets in batadv_purge_orig_ref(), by Eric Dumazet
-----BEGIN PGP SIGNATURE-----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=AUfY
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-pullrequest-20240405' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- prefer kfree_rcu() over call_rcu() with free-only callbacks,
by Dmitry Antipov
- bypass empty buckets in batadv_purge_orig_ref(), by Eric Dumazet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace open coded variant of device_is_compatible().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6025b9135f ("net: dqs: add NIC stall detector based on BQL")
added three sysfs files.
Use the recommended sysfs_emit() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Structures which are about to be copied to userspace shouldn't have
uninitialized fields or paddings.
memset() the whole &ip_tunnel_parm in ip_tunnel_parm_to_user() before
filling it with the kernel data. The compilers will hopefully combine
writes to it.
Fixes: 117aef12a7 ("ip_tunnel: use a separate struct to store tunnel params in the kernel")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/netdev/5f63dd25-de94-4ca3-84e6-14095953db13@moroto.mountain
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer hold RTNL while calling ip6addrlbl_dump()
("ip addrlabel show")
ip6addrlbl_dump() was already mostly relying on RCU anyway.
Add READ_ONCE()/WRITE_ONCE() annotations around
net->ipv6.ip6addrlbl_table.seq
Note that ifal_seq value is currently ignored in iproute2,
and a bit weak.
We might user later cb->seq / nl_dump_check_consistent()
protocol if needed.
Also change return value for a completed dump,
so that NLMSG_DONE can be appended to current skb,
saving one recvmsg() system call.
v2: read net->ipv6.ip6addrlbl_table.seq once, (David Ahern)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link:https://lore.kernel.org/netdev/67f5cb70-14a4-4455-8372-f039da2f15c2@kernel.org/
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fqdir_free_fn() is using very expensive rcu_barrier()
When one netns is dismantled, we often call fqdir_exit()
multiple times, typically lauching fqdir_free_fn() twice.
Delaying by one second fqdir_free_fn() helps to reduce
the number of rcu_barrier() calls, and lock contention
on rcu_state.barrier_mutex.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the ip6_vti and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Chevallier says:
====================
Introduce PHY listing and link_topology tracking
This is V11 for the link topology addition, allowing to track all PHYs
that are linked to netdevices.
This V11 addresses the various netlink-related issues that were raised
by Jakub, and fixes some typos in the documentation.
As a remainder, here's what the PHY listings would look like :
- eth0 has a 88x3310 acting as media converter, and an SFP module with
an embedded 88e1111 PHY
- eth2 has a 88e1510 PHY
PHY for eth0:
PHY index: 1
Driver name: mv88x3310
PHY device name: f212a600.mdio-mii:00
Downstream SFP bus name: sfp-eth0
PHY id: 0
Upstream type: MAC
PHY for eth0:
PHY index: 2
Driver name: Marvell 88E1111
PHY device name: i2c:sfp-eth0:16
PHY id: 21040322
Upstream type: PHY
Upstream PHY index: 1
Upstream SFP name: sfp-eth0
PHY for eth2:
PHY index: 1
Driver name: Marvell 88E1510
PHY device name: f212a200.mdio-mii:00
PHY id: 21040593
Upstream type: MAC
Ethtool patches : https://github.com/minimaxwell/ethtool/tree/link-topo-v6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some netlink commands are target towards ethernet PHYs, to control some
of their features. As there's several such commands, add the ability to
pass a PHY index in the ethnl request, which will populate the generic
ethnl_req_info with the relevant phydev when the command targets a PHY.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing the bus name is helpful when we want to expose the link topology
to userspace, add a helper to return the SFP bus name.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few PHY drivers that can handle SFP modules through their
sfp_upstream_ops. Introduce Phylib helpers to keep track of connected
SFP PHYs in a netdevice's namespace, by adding the SFP PHY to the
upstream PHY's netdev's namespace.
By doing so, these SFP PHYs can be enumerated and exposed to users,
which will be able to use their capabilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the phy_device as a parameter to the sfp upstream .disconnect_phy
operation. This is preparatory work to help track phy devices across
a net_device's link.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to. The PHY index can be
re-used for PHYs that are persistent.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same implementation is also valid for 88E1145. VCT in 88E1111 is
similar to the 88E609x family. The main difference lies in register
organization and required workarounds.
It utilizes the same fields in registers but requires a simpler
implementation.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink_compat_running_version() sticks out when running
netdevsim tests and watching dropped skbs. Add nlmsg_consume()
for cases were we want to free a netlink skb but it is expected,
rather than a drop. af_netlink code uses consume_skb() directly,
which is fine, but some may prefer the symmetry of nlmsg_new() /
nlmsg_consume().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->decrypted bit can be reused for other crypto protocols.
Remove the direct dependency on TLS, add helpers to clean up
the ifdefs leaking out everywhere.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu says:
====================
ynl: rename array-nest to indexed-array
rename array-nest to indexed-array and add un-nest sub-type support
====================
Link: https://lore.kernel.org/r/20240404063114.1221532-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add binary and integer sub-type support for indexed-array to display bond
arp and ns targets. Here is what the result looks like:
# ip link add bond0 type bond mode 1 \
arp_ip_target 192.168.1.1,192.168.1.2 ns_ip6_target 2001::1,2001::2
# ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/rt_link.yaml \
--do getlink --json '{"ifname": "bond0"}' --output-json | jq '.linkinfo'
"arp-ip-target": [
"192.168.1.1",
"192.168.1.2"
],
[...]
"ns-ip6-target": [
"2001::1",
"2001::2"
],
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20240404063114.1221532-3-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tp->window_clamp can be read locklessly, add READ_ONCE()
and WRITE_ONCE() annotations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://lore.kernel.org/r/20240404114231.2195171-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Recent changes added header flags to the spec.
Use an enum instead of defines for more seamless codegen.
[Jakub: drop the already applied parts and rewrite message]
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Link: https://lore.kernel.org/r/20240403212931.128541-6-rrameshbabu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
