Some users reported that they have machines with BMCs enabled that cannot
receive IPMI traffic after e1000e is loaded.
http://marc.info/?l=e1000-devel&m=121909039127414&w=2http://marc.info/?l=e1000-devel&m=121365543823387&w=2
This fixes the issue if they load with the new parameter = 0 by disabling
crc stripping, but leaves the performance feature on for most users.
Based on work done by Hong Zhang.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver fails to initialize the first time due to the failure in the
phy_id check the kernel triggers a warn_on on the second try to load the
driver because the driver did not free the msi/x resources in the first
load because of the previous failure in phy_id check.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e100 driver triggers BUG_ON(buf->direction != dir)
by doing pci_map_single(..., PCI_DMA_BIDIRECTIONAL)
and pci_dma_sync_single_for_device(..., PCI_DMA_TODEVICE).
Changing the DMA direction, especially with dmabounce will result
in unexpected behaviour.
Reported-by: Anders Grafstrom <grfstrm@users.sourceforge.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_printk() instead of printk() to give a little more context
and use consistent format.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed debug print statements and improved conditionals around informational statements.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
igb_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add support for the Marvell 88E1118 PHY which supports gigabit ethernet among other things.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the change the driver reported the same pause parameters
for all the ports, even only one of them was modified.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 46abc02175 ("phylib: give mdio
buses a device tree presence") added a call to device_unregister() in
a situation where the caller did not intend for the device to be
freed yet, but apart from just unregistering the device from the
system, device_unregister() does an additional put_device() that is
intended to free it.
The right function to use in this situation is device_del(), which
unregisters the device from the system like device_unregister() does,
but without dropping the reference count an additional time.
Bug report from Bryan Wu <cooloney@kernel.org>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Of the various WOL options provided in include/linux/ethtool.h, the
L1 NIC supports only magic packet. Remove all options except magic
packet from the atl1 driver.
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Inverting the crc after calling ether_crc_le() is unnecessary and breaks
multicast. Remove it.
Tested-by: David Madore <david.madore@ens.fr>
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We weren't unmapping DMA memory, which will break when gianfar gets used
on systems with more than 32-bits of memory. Also, it's just plain wrong.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
p_{tx,rx}_fw_statistics_pram are special: they're available only when
a device is open. If the device is closed, we should just fill the data
with zeroes.
Fixes the following oops:
root@b1:~# ifconfig eth1 down
root@b1:~# ethtool -S eth1
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc01e1dcc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01e1dcc] uec_get_ethtool_stats+0x98/0x124
LR [c0287cc8] ethtool_get_stats+0xfc/0x23c
Call Trace:
[cfaadde0] [c0287ca8] ethtool_get_stats+0xdc/0x23c (unreliable)
[cfaade20] [c0288340] dev_ethtool+0x2fc/0x588
[cfaade50] [c0285648] dev_ioctl+0x290/0x33c
[cfaadea0] [c0272238] sock_ioctl+0x80/0x2ec
[cfaadec0] [c00b5ae4] vfs_ioctl+0x40/0xc0
[cfaadee0] [c00b5fa8] do_vfs_ioctl+0x78/0x20c
[cfaadf10] [c00b617c] sys_ioctl+0x40/0x74
[cfaadf40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
---[ end trace b941007b2dfb9759 ]---
Segmentation fault
p.s. While at it, also remove u64 casts, they aren't needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is the next page of the scm recursion story (the commit
f8d570a4 net: Fix recursive descent in __scm_destroy()).
In function scm_fp_dup(), the INIT_LIST_HEAD(&fpl->list) of newly
created fpl is done *before* the subsequent memcpy from the old
structure and thus the freshly initialized list is overwritten.
But that's OK, since this initialization is not required at all,
since the fpl->list is list_add-ed at the destruction time in any
case (and is unused in other code), so I propose to drop both
initializations, rather than moving it after the memcpy.
Please, correct me if I miss something significant.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is pretty mature, and the worst of the known
problems has been fixed (the 32-bit failures due to readq
implementation).
So let's finally give it a version of 1.0
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Sun CP3260 ATCA blade which is
a N2 based ATCA blade with 2 NIU ports. The NIU ports do not
have on-board PHY.
Signed-off-by: Santwona Behera <santwona.behera@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix this warning:
net/bluetooth/af_bluetooth.c:60: warning: ‘bt_key_strings’ defined but not used
net/bluetooth/af_bluetooth.c:71: warning: ‘bt_slock_key_strings’ defined but not used
this is a lockdep macro problem in the !LOCKDEP case.
We cannot convert it to an inline because the macro works on multiple types,
but we can mark the parameter used.
[ also clean up a misaligned tab in sock_lock_init_class_and_name() ]
[ also remove #ifdefs from around af_family_clock_key strings - which
were certainly added to get rid of the ugly build warnings. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make 9p's RDMA option depend on INET since it uses Infiniband rdma_*
functions and that code depends on INET. Otherwise 9p can try to
use symbols which don't exist.
ERROR: "rdma_destroy_id" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_connect" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_create_id" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_create_qp" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_resolve_route" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_disconnect" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_resolve_addr" [net/9p/9pnet_rdma.ko] undefined!
I used an if/endif block so that the menu items would remain
presented together.
Also correct an article adjective.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure to pass netns_ok check is SILENT, except some MIB counter is
incremented somewhere.
And adding "netns_ok = 1" (after long head-scratching session) is
usually the last step in making some protocol netns-ready...
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two bugs:
1. setsockopt() of anything but a Type 2 routing header should return
EINVAL instead of EPERM. Noticed by Shan Wei
(shanwei@cn.fujitsu.com).
2. setsockopt()/sendmsg() of a Type 2 routing header with invalid
length or segments should return EINVAL. These values are statically
fixed in RFC 3775, unlike the variable Type 0 was.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bnx2 so that netpoll works properly. Specifically:
1) Fix parameters to bnx2_interrupt to be a struct bnx2_napi rather than a
struct net_device
2) Fix poll_controller method to check every queue in the rx case so frames
aren't missed
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a TX hang reported by Jesper Dangaard Brouer.
When an architecutre cannot provide a fully functional
64-bit atomic readq/writeq, the driver must implement
it's own. This is because only the driver can say whether
doing something like using two 32-bit reads to implement
the full 64-bit read will actually work properly.
In particular one of the issues is whether the top 32-bits
or the bottom 32-bits of the 64-bit register should be read
first. There could be side effects, and in fact that is
exactly the problem here.
The TX_CS register has counters in the upper 32-bits and
state bits in the lower 32-bits. A read clears the state
bits.
We would read the counter half before the state bit half.
That first read would clear the state bits, and then the
driver thinks that no interrupts are pending because the
interrupt indication state bits are seen clear every time.
Fix this by reading the bottom half before the upper half.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like mac80211 did, this driver makes 'clever' use of skb->cb to pass
information along with an skb as it is requeued from the virtual device
to the physical wireless device. Unfortunately, that trick no longer
works...
Unlike mac80211, code complexity and driver apathy makes this hack
the best option we have in the short run. Hopefully someone will
eventually be motivated to code a proper fix before all the effected
hardware dies.
(Above text by me. Johannes officially disavows all knowledge of this
hack. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the Sitecom 0001 v4 with product id 0x0df6:0028, uses Realtek's
RTL8187B and work fine with new 2.6.27 driver.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_notify_mac() function uses ieee80211_sta_req_auth() which
in turn calls ieee80211_set_disassoc() which calls a few functions that
need to be able to sleep, so ieee80211_notify_mac() cannot use RCU
locking for the interface list and must use rtnl locking instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In __sock_recv_timestamp() the additional SCM_TIMESTAMP[NS] is used. This
has the same value as SO_TIMESTAMP[NS], so this is a purely cosmetic change.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a minor bug in tcp_htcp.c which has been
highlighted by Lachlan Andrew and Lawrence Stewart. Currently, the
time since the last congestion event, which is stored in variable
last_cong, is reset whenever there is a state change into
TCP_CA_Open. This includes transitions of the type
TCP_CA_Open->TCP_CA_Disorder->TCP_CA_Open which are not associated
with backoff of cwnd. The patch changes last_cong to be updated
only on transitions into TCP_CA_Open that occur after experiencing
the congestion-related states TCP_CA_Loss, TCP_CA_Recovery,
TCP_CA_CWR.
Signed-off-by: Doug Leith <doug.leith@nuim.ie>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: handle HRTIMER_CB_IRQSAFE_UNLOCKED correctly from softirq context
nohz: disable tick_nohz_kick_tick() for now
irq: call __irq_enter() before calling the tick_idle_check
x86: HPET: enter hpet_interrupt_handler with interrupts disabled
x86: HPET: read from HPET_Tn_CMP() not HPET_T0_CMP
x86: HPET: convert WARN_ON to WARN_ON_ONCE
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: release buddies on yield
fix for account_group_exec_runtime(), make sure ->signal can't be freed under rq->lock
sched: clean up debug info
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ring-buffer: prevent infinite looping on time stamping
ftrace: disable tracing on resize
ftrace: fix breakage in bin_fmt results
ftrace: ftrace.txt version update
ftrace: update txt document
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
[XFS] XFS: Check for valid transaction headers in recovery
[XFS] handle memory allocation failures during log initialisation
[XFS] Account for allocated blocks when expanding directories
[XFS] Wait for all I/O on truncate to zero file size
[XFS] Fix use-after-free with log and quotas
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (21 commits)
ocfs2: Check search result in ocfs2_xattr_block_get()
ocfs2: fix printk related build warnings in xattr.c
ocfs2: truncate outstanding block after direct io failure
ocfs2/xattr: Proper hash collision handle in bucket division
ocfs2: return 0 in page_mkwrite to let VFS retry.
ocfs2: Set journal descriptor to NULL after journal shutdown
ocfs2: Fix check of return value of ocfs2_start_trans() in xattr.c.
ocfs2: Let inode be really deleted when ocfs2_mknod_locked() fails
ocfs2: Fix checking of return value of new_inode()
ocfs2: Fix check of return value of ocfs2_start_trans()
ocfs2: Fix some typos in xattr annotations.
ocfs2: Remove unused ocfs2_restore_xattr_block().
ocfs2: Don't repeat ocfs2_xattr_block_find()
ocfs2: Specify appropriate journal access for new xattr buckets.
ocfs2: Check errors from ocfs2_xattr_update_xattr_search()
ocfs2: Don't return -EFAULT from a corrupt xattr entry.
ocfs2: Check xattr block signatures properly.
ocfs2: add handler_map array bounds checking
ocfs2: remove duplicate definition in xattr
ocfs2: fix function declaration and definition in xattr
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (35 commits)
V4L/DVB (9516): cx18: Move DVB buffer transfer handling from irq handler to work_queue
V4L/DVB (9557): gspca: Small changes for the sensor HV7131B in zc3xx.
V4L/DVB (9556): gspca: Bad init sequence for sensor HV7131B in zc3xx.
V4L/DVB (9549): gspca: Fix a typo in one of gspca chips name.
V4L/DVB (9515): cx18: Use correct Mailbox IRQ Ack values and misc IRQ handling cleanup
V4L/DVB (9493): kconfig patch
V4L/DVB (9527): af9015: fix compile warnings
V4L/DVB (9524): af9013: fix bug in status reading
V4L/DVB (9511): cx18: Mark CX18_CPU_DE_RELEASE_MDL as a slow API call
V4L/DVB (9510): cx18: Fix write retries for registers that always change - part 2.
V4L/DVB (9506): ivtv/cx18: fix test whether modules should be loaded or not.
V4L/DVB (9499): cx88-mpeg: final fix for analogue only compilation + de-alloc fix
V4L/DVB (9496): cx88-blackbird: bugfix: cx88-blackbird-mpeg-users
V4L/DVB (9495): cx88-blackbird: bugfix: cx88-blackbird-poll-fix
V4L/DVB (9494): anysee: initialize anysee_usb_mutex statically
V4L/DVB (9492): unplug oops from dvb_frontend_init...
V4L/DVB (9486): ivtv/ivtvfb: no longer experimental
V4L/DVB (9485): ivtv: remove incorrect V4L1 & tvaudio dependency
V4L/DVB (9482): Documentation, especially regarding audio and informational links
V4L/DVB (9475): cx18: Disable write retries for registers that always change - part 1.
...
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Move legacy breadcrumb out of the reserved status page area
drm/i915: Filter pci devices based on PCI_CLASS_DISPLAY_VGA
drm/radeon: map registers at load time
drm: Remove infrastructure for supporting i915's vblank swapping.
i915: Remove racy delayed vblank swap ioctl.
i915: Don't whine when pci_enable_msi() fails.
i915: Don't attempt to short-circuit object_wait_rendering by checking domains.
i915: Clean up sarea pointers on leavevt
i915: Save/restore MCHBAR_RENDER_STANDBY on GM965/GM45
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
dsa: fix master interface allmulti/promisc handling
dsa: fix skb->pkt_type when mac address of slave interface differs
net: fix setting of skb->tail in skb_recycle_check()
net: fix /proc/net/snmp as memory corruptor
mac80211: fix a buffer overrun in station debug code
netfilter: payload_len is be16, add size of struct rather than size of pointer
ipv6: fix ip6_mr_init error path
[4/4] dca: fixup initialization dependency
[3/4] I/OAT: fix async_tx.callback checking
[2/4] I/OAT: fix dma_pin_iovec_pages() error handling
[1/4] I/OAT: fix channel resources free for not allocated channels
ssb: Fix DMA-API compilation for non-PCI systems
SSB: hide empty sub menu
vlan: Fix typos in proc output string
[netdrvr] usb/hso: Cleanup rfkill error handling
sfc: Correct address of gPXE boot configuration in EEPROM
el3_common_init() should be __devinit, not __init
hso: rfkill type should be WWAN
mlx4_en: Start port error flow bug fix
af_key: mark policy as dead before destroying
Clear buddies on yield, so that the buddy rules don't schedule them
despite them being placed right-most.
This fixed a performance regression with yield-happy binary JVMs.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Lin Ming <ming.m.lin@intel.com>
![](/avatar/43508f7a1ec957af441e34aa327a4088?size=56 "\\"Rafael J. Wysocki\"){kind=small}
