Move set_sysclk to codec level and people can use it at both
codec and dai level.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_pll function to codec level and people can use it at both
codec and dai level. Also, lower case "source" to keep it consistent.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If cs35l35->pdata.stereo is false then "ret" isn't initialized.
Fixes: 6387f866a2 ("ASoC: Add support for Cirrus Logic CS35L35 Amplifier")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove extraneous tab to correct the nesting level indentation
Detected by CoverityScan, CID#1416584 ("Nesting level does
not match indentation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As it is quite common to use a stereo pair of amps but share the IRQ
line between them both add the IRQF_SHARED flag whilst requesting
cs35l35's IRQ.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tidy up the code a little by adding a local variable for i2c_client->dev
rather than referring to it explicitly everytime.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for setting how the I2S pins are driven in unused slots,
currently the chip will just use the default of drive 0, however this
causes issues when multiple devices are attached to the same bus.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A return statement is missing just before the error paths at the end of
probe. This causes us to fall straight into the error path and disable
the supplies and re-enable reset, as these are only controlled during
probe this causes the part to no longer function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use manual mode for jack detection function to increase accuracy.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM is necessary for more than 2 channels. And there is no control bit
to specify which slots are using. Machine driver will not need to call
snd_soc_dai_set_tdm_slot if we do it in rt5665_hw_params.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vref3 is necessary for Mono Amp. So add it to dapm routes
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We got rt5665 private data from wrong work. It will result in kernel
panic.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Use the "cansleep" variant of gpiod_set_value so the driver can be used
with slow gpio controllers as well.
Fixes: 85825d5e88 ("ASoC: dio2125: add dio2125 amp driver")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dio2125 is a stereo output driver with adjustable gain.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Cirrus Logic
CS35L35 9V Boosted Amplifier
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not be writing acknowledge controls until the firmware is
running, as in the case of preloaded firmwares the DSP memory may be
unaccessible to whilst in the preloaded state. This means a write to the
control during this time could be lost.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Volatile controls should only be accessed when the firmware is active,
currently however writes to these controls will succeed, but the data
will be lost, if the firmware is powered down. Update this behaviour such
that an error is returned the same as it is for reads.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The es7134 is 24bit, 192Khz i2s DA converter for PCM audio.
Datasheet is available here : http://www.everest-semi.com/pdf/ES7134LV%20DS.pdf
This driver is also compatible with the es7144, which is the same as the
es7134, with 2 additional pins for filtering capacitors.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix not to update the iterator element, instead use list_del to remove
entry from the list.
This fixes the following coccinelle and static checker warning:
sound/soc/codecs/hdac_hdmi.c:1884:2-21:iterator with update on line
1885
sound/soc/codecs/hdac_hdmi.c:2011 hdac_hdmi_dev_remove()
error: potential NULL dereference 'port'.
Fixes: e0e5d3e5a53b('ASoC: hdac_hdmi: Add support for multiple ports to a PCM')
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pin list array iterator outside the iteration of the list can
point to dummy element, which can be invalid. So don't use pin variable
outside the pin list iteration.
This fixes the following coccinelle warning:
sound/soc/codecs/hdac_hdmi.c:1419:5-8: ERROR: invalid reference to the
index variable of the iterator
Fixes: 2acd8309a3a4('ASoC: hdac_hdmi: Add support to handle MST capable pin')
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Without this I am getting the following messages at boot on my Trimslice:
tlv320aic23-codec 2-001a: Control not supported for path LLINEIN -> [NULL] -> Line Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for LLINEIN --> NULL --> Line Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route LLINEIN -> NULL -> Line Input
tlv320aic23-codec 2-001a: Control not supported for path RLINEIN -> [NULL] -> Line Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for RLINEIN --> NULL --> Line Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route RLINEIN -> NULL -> Line Input
tlv320aic23-codec 2-001a: Control not supported for path MICIN -> [NULL] -> Mic Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for MICIN --> NULL --> Mic Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route MICIN -> NULL -> Mic Input
tegra-snd-trimslice sound: tlv320aic23-hifi <-> 70002800.i2s mapping ok
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The master and slave modes don't share the same table for MCLK/LRCLK
ratios. The slaves mode has bigger ratios that allow to use BCLK that
matche sampling frequency of 192khz.
This commit enables this rate only for slave mode, i.e it does not
declare this frequency in sysclk_contraints, resulting to an error in
master mode (not supported CLK).
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently most of the standard rates are supported by this driver.
Instead of defining each supported rate one by one, we use the SND macro
SNDRV_PCM_RATE_8000_48000. Also adds support for 88.2khz as the codec
supports it and the sys clocks are already supported.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In master mode, SCLK and LRCLK signals are generated by the CODEC when
any of the ADC/DAC are enabled. SCLK is derived from MCLK via a
programmable division set by BLK_DIV, LRCLK is derived from MCLK via
another programmable division set by ADCFsRatio/DACFsRatio.
In slave mode, SCLK and LRCLK signals are received as inputs and
supplied externally. LRCLK and SCLK must be synchronously derived from
MCLK with specific rates. The device can auto detect MCLK/LRCLK ratio
according to a predefined table. LRCLK/SCLK ratio is usually 64 (SCLK =
64 * LRCLK)
This commits adds support to let to device auto detect and decide which
ratio to use. The mclkdiv2 and BCLK_DIV ratio and put to zero.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix typos and add the following to the scripts/spelling.txt:
unneded||unneeded
Link: http://lkml.kernel.org/r/1481573103-11329-15-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
configurable LRC and BCLK divide. The driver
will make configurations of LRC and BCLK automatically according to
BCLK and FS information in master mode.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake is new Intel SoC, so add codec entry for HDMI
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake reference platform also uses combo jack for audio connector
so we need to set codec pdata to use this based on DMI match for this
board.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Represent each port as machine DAPM pin widget. This helps in
enable/disable pin when monitor is connected/disconnected in case pcm
is rendered to multiple ports.
Create machine pin widgets and pin switch kcontrol for each port and
report based on the pin status
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use snd_soc_jack instead of snd_jack and create the jack in machine
driver and pass the jack pointer to hdac_hdmi driver for jack
reporting.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we have the MST feature enabled and Pin-Port mux for user to
select the converter routing, multiple port mapping to same converter
needs to be supported.
To support multiple port mapped to same converter following changes are
done for this:.
o Add port list to pcm, so that multiple ports can be mapped to a PCM.
o Jack reporting in case where multiple port are attached to same PCM.
o Change hdac_hdmi_get_port_from_cvt(), channel_map, remove functions
to parse through all ports mapped to same the PCM.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable stream on a specific port of a MST capable pin, the port
needs to be selected before we configure the pin widget verb.
When port is selected, all the pin widget verb controlling the sink
device operation will be directed to selected port. So add port
selection before configuring the pin widget verb.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ELD notification can be received asynchronously from the graphics
side and this may happen just at the moment the sound driver is
initializing and notification will be missed. Similarly at system
resume, the notification is ignored as the ELD and connection states
are updated in anyway at the end of the resume.
So check the jack status in boot/resume by querying the port presence
based on pin caps and report the jack status.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support DP MST audio, new pin verbs/params are added. This patch
adds helper functions to do following:
o To set a specific port
o To get the currently selected port
o To get the length of port.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While unregistering the hdmi-codec, the hdmi device list must be
cleaned up. It avoid kernel page fault when registering again the
hdmi-codec.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To handle jack event and configuration of the pin widget for MST
capable pin, this patch adds:
o Flag to identify the pin is MST capable.
o In notify callback(), based on the pipe and port information marks if
the port is mst_capable. In case of non MST, port is defaulted to zero.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With MST each pin contains several ports to which device can be
connected.
As a preparatory work to support DP MST this patch adds below changes:
1. Defines the port structure and moves all stream related information
like ELD, converter list, chmap to port.
2. Creates ports for each pin based on the max_ports support.
3. Based on Pin-Port combination creates DAPM Mux widget instead of Pin
to allow user to select a converter.
4. Port zero is the default port when pin does not support MST.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The two front-ends to the codec can now be selected individually, but fail to
build when the bus support is missing:
sound/built-in.o: In function `es8328_spi_probe':
es8328-spi.c:(.text+0x125854): undefined reference to `__devm_regmap_init_spi'
sound/built-in.o: In function `es8328_spi_driver_init':
es8328-spi.c:(.init.text+0x3589): undefined reference to `__spi_register_driver'
Related to this, the added dependency on SND_SOC_ES8328 breaks:
warning: (SND_SOC_ALL_CODECS) selects SND_SOC_ES8328_I2C which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC && SND_SOC_ES8328 && I2C)
This adds the respective Kconfig dependencies and changes SND_SOC_ES8328 to a hidden
symbol that is selected implicitly by the two more specific options, as we do for
some other codecs. We have to remove the 'depends on' for SND_SOC_IMX_ES8328 in the
same step to avoid a recursive dependency.
Fixes: aa00f2c8af ("ASoC: Allow to select ES8328_I2C and ES8328_SPI directly")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, we have to select these symbols explictly via Kconfig, from
another entry. If we plan to use generic audio drivers like
simple-audio-card, the user need to be able to enable these symbols
directly via the menuconfig.
This commit also fixes unmet dependencies to SND_SOC_IMX_ES8328 caused
by these changes.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the function that changes the DAI format only supports master
mode. Trying to use a slave mode exits the function with -EINVAL and
leave the codec misconfigured. This commits adds support for enabling
the slave mode.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel info is part of the pcm parameter and channel map control is
created for each pcm. So move channel info to pcm instead of pin
structure and the mutex lock to pcm.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Optional gpio handling should not cause an error status and prevent
probing if it's missing. Remove error return for -ENOENT case and
move error message to dev_info
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This macro is unused since commit e369bd006f ("ASoC: wm8741: Allow master
clock switching").
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALC3270 is a low-cost version of RT5645, add ACPI ID
to enable probe and use rt5645 codec driver
Tested on Asus T100HA
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add ACPI ID 10EC5648 found e.g on Asus X205TA and use
rt5645 driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
the BIOS incorrectly reports this codec as 5640 but it is
really a rt5670
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ACPI ID "10EC3276" for sound card found on notebook HP Pavilion X2 10-p000.
ACPI DSDT Table on this device describes this card as ALC3276, but it is in fact rt5640.
Signed-off-by: Alexandrov Stansilav <neko@nya.ai>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CQ0093VC is no longer dependent on MFD_DAVINCI_VOICECODEC,
let's remove it. Otherwise, we can't compile it by COMPILE_TEST
on non-DAVINCE platform
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of hdmi connect/disconnect or when stream need to be route to
multiple monitors, corresponding port and audio infoframe needs to be
reconfigured. Currently all the configuration are done in DAI ops which
results in silence playback.
So use dapm widget event handlers to program audio infoframe and enable
/disable port configuration when widget is power on/off.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we are not disabling MEM_ENA on the error path, we should
really do this to unwind the state back to how it was. This patch adds a
clear of MEM_ENA on the error path, again there is no major issues
caused by this minor fix.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The booted and running flags should really only be set once all the
steps at that power level have been complete. Currently operations can
fail after the flags have been set, which would leave us in an
inconsistent state where the flags are set but the things expected to
reach that level have not happened. Whilst there isn't really any major
impact from this it is best to clean it up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent refactoring overlooked some places which should be covered by
the pwr_lock, all code that affects or depends on the power status of
the DSP should be covered, this patch adds the missing coverage.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds a compatible string for everest,es8388. This is
an audio codec that is compatible with es8328.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add user interface to provide channel mapping.
In a first step this control is read only.
As TLV type, the control provides all configuration available for
HDMI sink(ELD), and provides current channel mapping selected by codec
based on ELD and number of channels specified by user on open.
When control is called before the number of the channel is specified
(i.e. hw_params is set), it returns all channels set to UNKNOWN.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With codec read sometimes the pin_sense shows invalid monitor present
and eld_valid. Currently driver polls for few times to get the valid
eld data.
To avoid the latency, Instead of reading ELD from codec, read it
directly from the display driver using audio component framework.
and removed the unused direct codec helper functions.
Signed-off-by: Sandeep Tayal <sandeepx.tayal@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of enabling pin and cvt in pcm_open(), need to restore pin and
cvt state after system resume to restart the playback which is
paused/stopped before system suspend.
So enable pin and cvt in playback_prepare and call prepare when trigger
cmd is paused/started and resume to reconfigure pin and cvt.
Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
arizona_spk_init uses snd_soc_dapm_new_control which since
commit 37e1df8c95 ("ASoC: dapm: handle probe deferrals") will
occasionally request a probe deferral. Which means we should propagate the
error out of our driver from it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/rt5659.c:4236:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. For this large delay msleep() is preferable.
Link: http://lkml.org/lkml/2017/1/11/377
Fixes: commit 2b26dd4c1f ("ASoC: rt5660: add rt5660 codec driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop the const qualifier as it is being added by SOC_ENUM_DOUBLE_DECL()
already which is called by SOC_ENUM_SINGLE_DECL() here.
Fixes: commit 2b26dd4c1f ("ASoC: rt5660: add rt5660 codec driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop the const qualifier as it is being added by SOC_ENUM_DOUBLE_DECL()
already which is called by SOC_ENUM_SINGLE_DECL() as well as the
double const by calls to SOC_VALUE_ENUM_SINGLE_DECL() via
SOC_VALUE_ENUM_DOUBLE_DECL).
Fixes: commit d3cb2de247 ("ASoC: rt5659: add rt5659 codec driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declar rt5659_i2c_driver, which is only being passed to
module_i2c_driver(rt5659_i2c_driver), static.
Fixes: commit d3cb2de247 ("ASoC: rt5659: add rt5659 codec driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. For this large delay msleep() is preferable.
Fixes: commit d3cb2de247 ("ASoC: rt5659: add rt5659 codec driver")
Link: http://lkml.org/lkml/2017/1/11/377
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 70/80ms delays here passing the "min"
value to msleep(). This reduces the load on the hrtimer subsystem.
Link: http://lkml.org/lkml/2017/1/11/377
Fixes: commit 246693ba7b ("ASoC: rt5640: change widget sequence for depop")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace mdelay to msleep to avoid busy loop on ak4642_lout_event().
Otherwise, sometimes playback doesn't work correctly when pulseaudio
was used.
Signed-off-by: Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When trying to use simple card with wm8962 the following probe
error happens:
wm8731 0-001a: simple-card: set_sysclk error
In simple-card.c the snd_soc_dai_set_sysclk() function is called with
clk_id as 0, which is an invalid clock for wm8731.
Adjust the clocks source definitions in wm8731.h so that the simple
card driver can work successfully
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default capless power mode is low voltage mode. We should set
it to high voltage mode to get fair headphone performance.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2s clock pre-divider 1 is used for both i2s1 and sysclk.
The i2s1 is usually used for the main i2s and the pre-divider
will be set in hw_params function.
However, if i2s2 is used, the pre-divider is not set in the hw_params
function and the default value of i2s clock pre-divider 1 is too high
for sysclk and DMIC usage. Fix by overriding default divider value to 2.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=95681
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As requirements to bring up audio paths are continuous getting tighter
and the DSP download to most ADSP devices happens over an external bus
it can become an important factor in the path bring up time. As such
sometimes it is a reasonable trade off to download the firmware ahead of
when it will be required and take a small hit on power consumption for
keeping the core powered up.
This "preloading" adds an additional control for each DSP core "DSPx
Preload Switch" that when set to true will power up the DSP core and
download the firmware currently selected in the "DSPx Firmware" control.
Whilst the core is preloaded the current firmware can not be changed and
the CODEC will be kept powered up and SYSCLK held on. Although future
improvements may allow the SYSCLK to be powered down as well because
the hardware only requires SYSCLK whilst the download is actually taking
place, but this is not covered in this series.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DAC L2 Power" and "DAC R2 Power" are used by both rt5639 and rt5640.
But it was defined in rt5640_specific_dapm_widgets[]. Move them to
rt5640_dapm_widgets will let both rt5639 and rt5640 can use it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clk_ref_div is not configured in the correct position of the
register. The patch fixes that clk_ref_div, Pre-Scalar, is assigned
the wrong value.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the codec is powered on, it's registers are in reset state as the
power off will do a soft reset of the codec.
After the register sync we need to add delay to remove the pop-noise on
stream start.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The RESET register only have one self clearing bit and it should not be
cached. If it is cached, when we sync the registers back to the chip we
will initiate a software reset as well, which is not desirable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Protect against corrupt firmware files by ensuring that the length we
get for the data in a region actually lies within the available firmware
file data buffer.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For TDM mode, the I2S data out line can be shared between mutliple
codecs. In this scenario, only the active codec should be using
the line, and all others should be high impedance. However,
currently in the driver this configuration isn't set when capture
is inactive, and the line remains driven.
This patch updates the AIF_OUT widget to set the DAI output pin of
the device as high impedance when not in use.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/wm0010.c does not use any miscdevice so this patch
remove this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/rt5677-spi.c does not use any miscdevice so this patch
remove this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/rt5514-spi.c does not use any miscdevice so this patch
remove this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a control to allow swapping HiFi DAC Left/Right channels.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
In pcm3168a_hw_params(), 'format' is initialized but never used.
sound/soc/codecs/pcm3168a.c: In function ‘pcm3168a_hw_params’:
sound/soc/codecs/pcm3168a.c:405:19: warning: variable ‘format’ set but not
used [-Wunused-but-set-variable]
snd_pcm_format_t format;
Cc: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In max9867_dai_set_fmt(), 'ret' is initialized as return value of
regmap_raw_write() but never checked, so remove this and assignement.
sound/soc/codecs/max9867.c: In function ‘max9867_dai_set_fmt’:
sound/soc/codecs/max9867.c:312:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret;
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In adau17x1_pll_event(), 'ret' is initialized as return value of
regmap_raw_write() but never checked, so remove this and assignement.
sound/soc/codecs/adau17x1.c: In function ‘adau17x1_pll_event’:
sound/soc/codecs/adau17x1.c:68:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret;
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In max98090_probe(), code checks for micbias being out of range. The
'micbias' variable in unsigned and checked against M98090_MBVSEL_2V2 which
is zero, so remove this check.
sound/soc/codecs/max98090.c: In function ‘max98090_probe’:
sound/soc/codecs/max98090.c:2459:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
} else if (micbias < M98090_MBVSEL_2V2 || micbias > M98090_MBVSEL_2V8) {
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- Support for stereo DAPM controls
- Some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- A new version of the topology ABI; this should be backward compatible
- Updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- New drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- Yet another race fix at disconnection
- Tolerated packet size calculation for some Android devices
- Quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- Improvement of Dell pin fixup mapping
- Quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- Replace all kthread usages with simple works
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=WZeb
-----END PGP SIGNATURE-----
Merge tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- support for stereo DAPM controls
- some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- a new version of the topology ABI; this should be backward
compatible
- updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- new drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- yet another race fix at disconnection
- tolerated packet size calculation for some Android devices
- quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- improvement of Dell pin fixup mapping
- quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- replace all kthread usages with simple works"
* tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (296 commits)
ALSA: hiface: Fix M2Tech hiFace driver sampling rate change
ALSA: usb-audio: Eliminate noise at the start of DSD playback.
ALSA: usb-audio: Add native DSD support for TEAC 501/503 DAC
ASoC: wm_adsp: wm_adsp_buf_alloc should use kfree in error path
ASoC: topology: avoid uninitialized kcontrol_type
ALSA: usb-audio: Add QuickCam Communicate Deluxe/S7500 to volume_control_quirks
ALSA: usb-audio: add implicit fb quirk for Axe-Fx II
ASoC: zte: spdif: correct ZX_SPDIF_CLK_RAT define
ASoC: zte: spdif and i2s drivers are not zx296702 specific
ASoC: rsnd: setup BRGCKR/BRRA/BRRB when starting
ASoC: rsnd: enable/disable ADG when suspend/resume timing
ASoC: rsnd: tidyup ssi->usrcnt counter check in hw_params
ALSA: cs46xx: add a new line
ASoC: Intel: update bxt_da7219_max98357a to support quad ch dmic capture
ASoC: nau8825: disable sinc filter for high THD of ADC
ALSA: usb-audio: more tolerant packetsize
ALSA: usb-audio: avoid setting of sample rate multiple times on bus
ASoC: cs35l34: Simplify the logic to set CS35L34_MCLK_CTL setting
ALSA: hda - Gate the mic jack on HP Z1 Gen3 AiO
ALSA: hda: when comparing pin configurations, ignore assoc in addition to seq
...
buf was allocated by kzalloc() so it should be passed to kfree()
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This bit will enable 4th order SINC filter.
=1, filter will enable; but it consumes higher power.
=0, the sinc filter is disable, and it should always keep 0 value to
get high THD.
Therefor, disable the filter when codec initiation for better
performance when recording.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The logic of "value = ~CS35L34_MCLK_DIV & CS35L34_MCLK_RATE_XXXXXX;" is
unnecessary complex. By setting CS35L34_MCLK_DIV | CS35L34_MCLK_RATE_MASK
as the mask for regmap_update_bits() call, what the code does is exactly
the same as setting value = CS35L34_MCLK_RATE_XXXXXX.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using regmap_update_bits(..., mask, 1) with 'mask' following (1 << k)
and k greater than 0 is wrong. Indeed, _regmap_update_bits will perform
(mask & 1), which results in 0 if LSB of mask is 0. Thus the call
regmap_update_bits(..., mask, 1) is in reality equivalent to
regmap_update_bits(..., mask, 0).
In such a case, the correct use is regmap_update_bits(..., mask, mask).
This driver is performing such a mistake with the CS42L56_AIN*_REF_MASK
masks, which equal 0x10, 0x20, 0x40 and 0x80. Fix the driver to make it
consistent with the API. Please note that this change is untested,
as I do not have this piece of hardware. Testers are welcome!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an issue about pop noise in NAU88L25 as follows.
Issue 54078: Chell_headphone pop back from S3
(1)Play directly to hw, bypassing CRAS:
sox -b 16 -n -t alsa hw:0,0 synth sine 200 sine 200
(2)Close lid or powerd_dbus_suspend, then press a key to resume.
(3)no audio after resume
(4)Audio will be back after close then reopen the pcm device.
After verification, we find one defect is that semaphone lock is not
long enough and expired. In this situation, the playback comes back
early but pauses a while to wait for the crosstalk detection done.
But the detection spends too much time and lock time is up. Therefore,
the playback and jack detection sequence interfere to each other.
That breaks sequence and makes noise. The driver extends the lock
time for the issue.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to modify the state of some of our own pins and are currently
not taking account that the pin name may have a name_prefix applied
to it.
Replace the snd_soc_dapm_x_pin functions with the equivalent
snd_soc_component_x_pin functions so that any name_prefix will be
handled automatically.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5670 driver supports also RT5672 codec, but its ACPI ID is missing.
This was found on Dell Wyse 3040 box.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dell Wyse 3040 requires the platform workaround for enabling dmic and
jack detection as defined for Braswell CRB.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
drm/qxl: various bugfixes and cleanups,
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=OYiT
-----END PGP SIGNATURE-----
Merge tag 'drm-qemu-20161121' of git://git.kraxel.org/linux into drm-next
drm/virtio: fix busid in a different way, allocate more vbufs.
drm/qxl: various bugfixes and cleanups,
* tag 'drm-qemu-20161121' of git://git.kraxel.org/linux: (224 commits)
drm/virtio: allocate some extra bufs
qxl: Allow resolution which are not multiple of 8
qxl: Don't notify userspace when monitors config is unchanged
qxl: Remove qxl_bo_init() return value
qxl: Call qxl_gem_{init, fini}
qxl: Add missing '\n' to qxl_io_log() call
qxl: Remove unused prototype
qxl: Mark some internal functions as static
Revert "drm: virtio: reinstate drm_virtio_set_busid()"
drm/virtio: fix busid regression
drm: re-export drm_dev_set_unique
Linux 4.9-rc5
gp8psk: Fix DVB frontend attach
gp8psk: fix gp8psk_usb_in_op() logic
dvb-usb: move data_mutex to struct dvb_usb_device
iio: maxim_thermocouple: detect invalid storage size in read()
aoe: fix crash in page count manipulation
lightnvm: invalid offset calculation for lba_shift
Kbuild: enable -Wmaybe-uninitialized warnings by default
pcmcia: fix return value of soc_pcmcia_regulator_set
...
Disable IRQ when jack is NULL in rt298_mic_detect. So machine driver
can use it in suspend/resume.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions are given external linkage by default making the extern's
unnecessary, as such remove them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions are given external linkage by default making the extern's
unnecessary, as such remove them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fields of structs with global storage are implicitly initialized to 0/NULL,
there is usually no need to do this explicitly.
Removing the initialization of the legacy suspend/resume callback fields
also gets the driver ready for the day when they are eventually removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Resources should be requested when the device is probed on the control bus
rather then when the CODEC is bound to the sound card. This allows things
like probe deferring and device managed allocations to work.
So move the GPIO request calls from the CODEC probe to the bus probe and
also make them managed along the way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are not checking the return value from a call to wm_adsp_buffer_init
it looks like this used to be returned at the bottom of the function but
probably got missed when more error paths were added. This patch adds
the appropriate error check.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The kcontrol pointer in wm_coeff_ctl is not used now.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were adding firmware controls as card controls (using
snd_soc_add_codec_controls). The DSP is part of a specific codec so
we should be adding them as codec controls. Adding as codec controls
also means that if the codec has a name_prefix it will be added to
the control name, which won't happen when adding as a card control.
As that was the only use of the card pointer in struct wm_adsp it can
be removed.
For ADSP2 codecs a wm_adsp2_codec_probe() was added since the original
control handling was written, and that's the logical place to store a
pointer to the codec rather than delaying it until the codec is
powered-up.
For ADSP1 we don't use a codec_probe() stage so the codec pointer
initialization replaces the original card pointer initialization in
wm_adsp1_event().
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8580 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C), and use module_i2c_driver().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8523 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C), and use module_i2c_driver().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control list may contain shutdown controls for firmwares that are
not currently active, attempting to write this will at best fail. To
avoid this issue we skip any control that is not active.
Fixes: commit f4f0c4c60c ("ASoC: wm_adsp: Signal firmware shutdown
through event control")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm9081 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C)
And, this patch adds "depends on I2C" to Kconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
uda1380 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C), and use module_i2c_driver().
And, this patch adds "depends on I2C" to Kconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The lookup of the base register corresponding to a control is
duplicated in read and write so factor it out into a separate
function.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rtd->codec does not necessarily point to the CODEC instance for which the
callback was called (e.g. for CODEC<->CODEC or multi-CODEC links). Use
dai->codec instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAC3101 is mostly identical to DAC3100 with the exception that it has
stereo speaker AMP instead of mono used in DAC3100.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch handles publishing acknowledged controls through ALSA.
These controls allow user-side to send events to the firmware and
wait for the firmware to acknowledge it.
Note that although acked controls only operate in the direction
host->firmware, and therefore they are write-only as seen from user-
side code, we have to make them readable to account for all the code
out there that assumes that ALSA controls are always readable (amixer
for example.)
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for firmware controls marked SYSTEM. These are
internal to the driver-firmware interface and do not have
a user-accessible ALSA control.
Signed-off-by: Stuart Henderson <stuarth@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch factors out converting a memory region type into
a name string, mainly so that it can be used in log commands.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the firmware has any system event signalling controls, signal
them during DSP PRE_PMD to tell the firmware it is about to be stopped.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver fine-tune some parameters to improve FLL performance.
Those items have description as follow.
(1)ICTRL_LATCH: FLL DSP speed capability control
When FLL running at high frequency with long decimal number, DSP needs
to operate at high speed. FLL DSP can optimize between performance and
power consumption by ICTRL_LATCH.(111 has highest power consumption.)
The default setting can be used to reduce power.
(2)CUTOFF500: loop filter cutoff frequency at 500Khz
It will give the best FLL performance but highest power consumption
to enable the cutoff frequency. FLL Loop Filter enable to reduce FLL
output noise, especially,(DCO frequency)/(FLL input reference frequency)
is not a integer.
(3)GAIN_ERR: FLL gain error correction threshold setting
The threshold is comparison between DCO and target frequency.
The value 1111 has the most sensitive threshold, that is, 1111 can have
the most accurate DCO to target frequency. However, the gain error setting
conditionally and inversely depends on FLL input reference clock rate.
Higher FLL reference input frequency can only set lower gain error, such
as 0000 for input reference from MCLK=12.288Mhz. On the other side, if FLL
reference input is from Frame Sync, 48KHz, higher error gain can apply
such as 1111.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Over Sampling Rate (OSR) is defined as CLK_ADC frequency divided by the
audio sample rate (Fs).
OSR = CLK_ADC / FS
The available OSRs are 32, 64, 128 or 256. Note that the OSR and Fs
values must be selected such that the maximum frequency of CLK_ADC
is less than 6.144 MHz. It is recommended to match the relationship
between OSR and clock SRC according to following Table.
ADC_RATE: 00(OSR=32) | CLK_ADC_SRC: 11(CODEC 1/8)
ADC_RATE: 01(OSR=64) | CLK_ADC_SRC: 10(CODEC1/4)
ADC_RATE: 10(OSR=128) | CLK_ADC_SRC: 01(CODEC 1/2)
ADC_RATE: 11(OSR=256) | CLK_ADC_SRC: 00(CODEC CLK)
The over sampling rate about DAC follows the same rule with ADCs.
The driver changes the OSR to 64 value when initiation for better FLL
performance and applies the dynamic SRC change by different OSR.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the short Frame Sync detection logic enabled, the logic will check the
short frame sync threshold. If frame sync is less than the setting;
for example, frame sync less than 252 MCLK, the short frame sync signal is
flagged, digital filter temporary mute and skip that data.
If the system was intended for sampling rate change which could create
temporary short frame sync and not enough MIPS to run the digital filter.
But the situation doesn't happen in ALSA architecure. Thus the Frame Sync
is always stable, then no require to do the detection. Therefore,
the dirver disables the function for better performance.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The compatible table was not updated when the support for DAC3100 was added.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to arizona_init_notifiers was only added for CODECs that are
generating voice trigger events, however, this is somewhat annoying
for machine drivers that might be used with multiple CODECs as they
need to conditionally register for the notifier, depending on the
CODEC being attached.
As the cost of initialising the notifier is so minimal, and we may
well add other events in the future that apply to more CODECs, simply
do this for all Arizona CODECs.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These functions are very thin wrappers around core functions, so they
make sense as inline functions. Also making them inline avoids build
issues in the case where the machine driver is built in but the CODEC
is built as a module.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core expects "const char * const" and "unsigned int" for enum
controls, the mixer control definitions in wm2200 use "const char *"
and "int". This patch corrects the type of these arrays.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/cs42l42.c:1972:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pm8916_wcd_analog_enable_micbias_int1() should set micbias1_cap_mode
rather than micbias2_cap_mode.
Also change the order of pm8916_wcd_analog_enable_micbias_int1/init2
functions for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using simple-card with the wm8978 doesn't work because simple card calls
set_sysclk on the clock index 0, which is not the MCLK in the WM8978.
Adjust the clock definition so that the clock 0 is the MCLK.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Cirrus Logic CS42L42 codec. SoundWire support
is not enabled. Features support for I2C control and I2S audio.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove
the wrappers.
Also use snd_soc_update_bits() where appropriate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the stac9766 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the stac9766
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stac9766 driver has a header file that defines 3 register locations.
Move these to the main source file since it is not really worth it having a
separate file for them. The header file is now empty and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AC'97 standard defines paging support for the register range 0x60-0x6f.
Meaning registers in this window are mapped to different physical registers
depending on the setting of the page select register (0x24).
The stac9766 implements support for switching between page 0 and page 1
depending on the addressed register. But the driver never accesses any
registers from page 1, in addition page 0 is the page selected by default.
Considering the development history it is unlikely that the driver will see
any new features that require paging support. Removing the paging support
makes transitioning the driver to regmap a bit more straight forward.
The default register value table is update to contain the values from page
0, rather than page 1.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used instead and the defines are
unused.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch renames msm8916_wcd_digital_parse_dt() to
msm8916_wcd_digital_get_clks() as the function is not directly dealing
with dt parsing.
No functional changes done.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the code which is not parsing dt from pm8916_wcd_analog_parse_dt()
to make it clear to reader.
No functional changes done.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support double channel shared controls split across 2 registers, one
for each channel, we must be able to update both registers together.
Add a second set of register fields to struct snd_soc_dapm_update, and
update the DAPM control writeback (put) callbacks to support this.
For codecs that use custom events which call into DAPM to do updates,
also clear struct snd_soc_dapm_update before using it, so the second
set of fields remains clean.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/codecs/wm8580.c:988:33: warning:
symbol 'wm8580_data' was not declared. Should it be static?
sound/soc/codecs/wm8580.c:992:33: warning:
symbol 'wm8581_data' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mono ADC Capture Switch control is missing in the driver. So, add it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a DAI specifies "#sound-dai-cells = <0>" in device-tree then
hdmi_of_xlate_dai_name() will be called with zero args, which it isn't
implemented to cope with. The resulting use of an uninitialised variable
for the id will usually result in an error like:
asoc-simple-card sound: parse error -11
asoc-simple-card: probe of sound failed with error -11
Fix this by using and id of zero if no arg is provided.
Fixes: 9731f82d60 ("ASoC: hdmi-codec: enable multi probe for same device")
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
da7219 output (for headset capture) should be set to high-impedance when
not in use, since it will otherwise interfere with output from other
codecs attached to the same DAI.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's difficult to guess from bunch of "ret=-121" errors what driver and
device actually caused them. Since struct i2c_client has the dev pointer
use that for dev_err() with meaningful error message.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4c5d146929 ("ASoC: max98504: Add max98504 speaker amplifier
driver") added new max98504, but this patch didn't add it to
SND_SOC_ALL_CODECS. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the compressed ops run on the platform side of things we should
really access the driver data through the platform pointer rather than
the CODEC pointer. As the compressed DAIs in our systems always connect
our CODEC to our platform this has never been an issue, but should still
be corrected. Additionally it clears the way for future core refactoring
work.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 31833ead95 ("ASoC: arizona: Move request of speaker IRQs into bus probe")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some registers accesses are done in atomic context.
Enable fast io to use spinlock instead of mutex to protect access.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
stih416 is no more supported, clean associated code.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the DSP compressed data IRQ from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the speaker thermal event IRQs from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CS35L34_CHIP_ID is not a register address, it's the value read from
CS35L34_DEVID_AB/CD/E registers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't manually enable cache_bypass for reading the ID registers they
don't have a default anyway so the first read will always hit the
hardware. The old code worked this is simply the more standard way
to implement this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather than manually enabling cache bypass when reading the ID registers
simply remove the default which will cause the first read to go to the
hardware. The old code worked this is simply the more standard way to
implement this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather than manually enabling cache bypass when reading the ID registers
simply remove the default which will cause the first read to go to the
hardware. The old code worked this is simply the more standard way to
implement this. There is a comment included in the code that claims the
chip ID register also contains the right input volume, however this is
clearly not the case from the rest of the driver. Further investigation
reveals exactly the same comment in the wm8962 driver, where this is the
case, so this is almost certainly a copy and paste error from when the
driver was created.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the DMIC that needs time to initial after the MCLK is provided, the
field of delay time is implemented by the platform data.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- first slice of the gvt device model (Zhenyu et al)
- compression support for gpu error states (Chris)
- sunset clause on gpu errors resulting in dmesg noise telling users
how to report them
- .rodata diet from Tvrtko
- switch over lots of macros to only take dev_priv (Tvrtko)
- underrun suppression for dp link training (Ville)
- lspcon (hmdi 2.0 on skl/bxt) support from Shashank Sharma, polish
from Jani
- gen9 wm fixes from Paulo&Lyude
- updated ddi programming for kbl (Rodrigo)
- respect alternate aux/ddc pins (from vbt) for all ddi ports (Ville)
* tag 'drm-intel-next-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (227 commits)
drm/i915: Update DRIVER_DATE to 20161024
drm/i915: Stop setting SNB min-freq-table 0 on powersave setup
drm/i915/dp: add lane_count check in intel_dp_check_link_status
drm/i915: Fix whitespace issues
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_ddc_pin for all DDI ports
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: Remove WaEnableYV12BugFixInHalfSliceChicken7
drm/i915: KBL - Recommended buffer translation programming for DisplayPort
drm/i915: Move down skl/kbl ddi iboost and n_edp_entires fixup
drm/i915: Add a sunset clause to GPU hang logging
drm/i915: Stop reporting error details in dmesg as well as the error-state
drm/i915/gvt: do not ignore return value of create_scratch_page
drm/i915/gvt: fix spare warnings on odd constant _Bool cast
drm/i915/gvt: mark symbols static where possible
drm/i915/gvt: fix sparse warnings on different address spaces
drm/i915/gvt: properly access enabled intel_engine_cs
drm/i915/gvt: Remove defunct vmap_batch()
drm/i915/gvt: Use common mapping routines for shadow_bb object
drm/i915/gvt: Use common mapping routines for indirect_ctx object
...
