Use of_device_get_match_data() helper to get the match-data.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20210114152700.21916-2-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GL9763E enters ASPM L1 state after a very short idle in default,
even during a burst of request. So the R/W performance of GL9763E
is low with some platforms, which support ASPM mechanism, due to
entering ASPM L1 state very frequently in R/W process. Set the L1
entry delay bits in vendor-specific register to 0x3FF to enlarge
the idle period to 260us for improving the R/W performance
of GL9763E.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Link: https://lore.kernel.org/r/20210115054736.27769-1-reniuschengl@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the controller present on the AM64x SoC.
There are instances:
sdhci0: 8bit bus width, max 400 MBps
sdhci1: 4bit bus width, max 100 MBps
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210113115908.3882-3-a-govindraju@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make sure voltage is below 0.5V before power on during a power cycle,
add a delay of at least 100ms. The delays in the mmc core is not sufficient
for the rtsx pci device.
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20210113105723.7916-1-ricky_wu@realtek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the device suspend process begins before the mmc host's autosuspend
timeout, the host will continue running during system sleep. Avoid
this by forcing runtime suspend during a global suspend transition.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20210113052421.36553-1-samuel@sholland.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds new compatible string to differentiate
between the controllers versions included in the AP807
north bridge. Thanks to this change, the SoCs which use
AP807 will not run unintentionally in the 'slow mode'
with disabled UHS modes.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20210112094655.12274-3-kostap@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change code style of mapping the syscon in sdhci_arasan_update_support64b()
for readability and consistency.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210111155001.12307-3-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 36c6aadaae ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
introduces syscon map sdhci_arasan_update_support64b(). Unfortunately,
kernel-doc format script tool has not been run before and causing warning
on the documentation style.
Below is the output when running the kernel-doc script tool:
drivers/mmc/host/sdhci-of-arasan.c:1388: warning: contents before sections
Let's fix this by using standard conventions kernel-doc format.
Fixes: 36c6aadaae ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210111155001.12307-2-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a vendor-specific bit named GLI_9763E_MB_ERP_ON at the bit7 of
register 888h to decide whether to enhance random R/W performance
of GL9763E. CQHCI support will be enabled if and only if the bit is
set and the GLI_9763E_MB_CMQ_OFF bit is not set.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Link: https://lore.kernel.org/r/20210106085332.5494-1-reniuschengl@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the datasheet, this controller needs retune when
cmd or data timeout happens. So, add a condition into .check_retune().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608708622-29668-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, busy timeout is not checked for data transfer command. But,
if the temperature condition changes, the data cannot be acquired
correctly and timeout may occur. Also, we could reproduce an issue by
using mmc_test driver (e.g. "Correct xfer_size at write (start
failure)"). Therefore, this adds timeout error check.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[saito: rework commit message.]
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[shimoda: rebase, add commit description]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608708622-29668-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable SGDMA support for SD_IO_RW_EXTENDED and add proper check
for scatterlist size alignment in block mode.
According to documentation, in SDIO block mode meson-gx DMA could
only handle buffers with sizes that are multiples of SDIO block size.
Some SDIO drivers like brcmfmac use scatterlist API, but do not enforce
proper scatterlist buffer size alignemnt, this looks like a root cause
of non-working CMD53.
Some minor style fixes.
Signed-off-by: Dmitry Lebed <lebed.dmitry@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201218075312.67338-1-lebed.dmitry@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when get request SW timeout, if CMD/DAT xfer done irq coming right now,
then there is race between the msdc_request_timeout work and irq handler,
and the host->cmd and host->data may set to NULL in irq handler. also,
current flow ensure that only one path can go to msdc_request_done(), so
no need check the return value of cancel_delayed_work().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add pre_req and post_req support to improve performance.
Inspired by a patch in the BSP by Masaharu Hayakawa.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608114572-1892-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the latest datasheet, the internal DMAC buffer alignment
R-Car Gen3 SDHI HW should be 128-bytes. So, fix it.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[shimoda: revise commit description, rebase]
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608114572-1892-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MSM SDHCI driver always set the "actual_clock" field to 0. It had
a comment about it not being needed because we weren't using the
standard SDHCI divider mechanism and we'd just fallback to
"host->clock". However, it's still better to provide the actual
clock. Why?
1. It will make timeout calculations slightly better. On one system I
have, the eMMC requets 200 MHz (for HS400-ES) but actually gets 192
MHz. These are close, but why not get the more accurate one.
2. If things are seriously off in the clock driver and it's missing
rates or picking the wrong rate (maybe it's rounding up instead of
down), this will make it much more obvious what's going on.
NOTE: we have to be a little careful here because the "actual_clock"
field shouldn't include the multiplier that sdhci-msm needs
internally.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/20201214092048.v5.2.I7564620993acd4baa63fa0e3925ca879a86d3ee3@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As talked about in commit 5e4b7e82d4 ("clk: qcom: gcc-sdm845: Use
floor ops for sdcc clks"), most clocks handled by the Qualcomm clock
drivers are rounded _up_ by default instead of down. We should make
sure SD/MMC clocks are always rounded down in the clock drivers.
Let's add a warning in the Qualcomm SDHCI driver to help catch the
problem.
This would have saved a bunch of time [1].
NOTE: this doesn't actually fix any problems, it just makes it obvious
to devs that there is a problem and that should be an indication to
fix the clock driver.
[1] http://lore.kernel.org/r/20201210102234.1.I096779f219625148900fc984dd0084ed1ba87c7f@changeid
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201214092048.v5.1.Iec3430c7d3c2a29262695edef7b82a14aaa567e5@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds support for A100 MMC controller, which use word address
for internal dma.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20201211011934.6171-10-andre.przywara@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_PRESET_FOR_* registers are not set(all read as zeros), so
set the quirk.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201210165510.76b917e5@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A call to 'ausdhi6_dma_release()' to undo a previous call to
'usdhi6_dma_request()' is missing in the error handling path of the probe
function.
It is already present in the remove function.
Fixes: 75fa9ea6e3 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201217210922.165340-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'sdhci_remove_host()' and 'sdhci_pltfm_free()' should be used in place of
'mmc_remove_host()' and 'mmc_free_host()'.
This avoids some resource leaks, is more in line with the error handling
path of the probe function, and is more consistent with other drivers.
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Orson Zhai <orson.zhai@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201217204236.163446-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'dma_request_chan()' calls should be balanced by a corresponding
'dma_release_channel()' call.
Add the missing call both in the error handling path of the probe function
and in the remove function.
Fixes: ff65ffe46d ("mmc: Add Actions Semi Owl SoCs SD/MMC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201209194202.54099-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e7b5d63a82 ("mmc: sdhci-brcmstb: Add shutdown callback")
that added a shutdown callback to the diver, is causing "mmc timeout"
errors on S5 suspend. The problem was that the "remove" was queuing
additional MMC commands after the "shutdown" and these caused
timeouts as the MMC queues were cleaned up for "remove". The
shutdown callback will be changed to calling sdhci-pltfm_suspend
which should get better power savings because the clocks will be
shutdown.
Fixes: e7b5d63a82 ("mmc: sdhci-brcmstb: Add shutdown callback")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210107221509.6597-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Automatic Clock Gating is a feature used for the power consumption
optimisation. It turned out that during early init phase it may prevent the
stable voltage switch to 1.8V - due to that on some platforms an endless
printout in dmesg can be observed: "mmc1: 1.8V regulator output did not
became stable" Fix the problem by disabling the ACG at very beginning of
the sdhci_init and let that be enabled later.
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201211141656.24915-1-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a44f7cb937 ("mmc: core: use mrq->sbc when sending CMD23 for
RPMB") began to use ACMD23 for RPMB if the host supports ACMD23. In
RPMB ACM23 case, we need to set bit 31 to CMD23 argument, otherwise
RPMB write operation will return general fail.
However, no matter V4 is enabled or not, the dwcmshc's ARGUMENT2
register is 32-bit block count register which doesn't support stuff
bits of CMD23 argument. So let's handle this specific ACMD23 case.
From another side, this patch also prepare for future v4 enabling
for dwcmshc, because from the 4.10 spec, the ARGUMENT2 register is
redefined as 32bit block count which doesn't support stuff bits of
CMD23 argument.
Fixes: a44f7cb937 ("mmc: core: use mrq->sbc when sending CMD23 for RPMB")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201229161625.38255233@xhacker.debian
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Initial support for SD express card/host
MMC host:
- mxc: Convert the driver to DT-only
- mtk-sd: Add HS400 enhanced strobe support
- mtk-sd: Add support for the MT8192 SoC variant
- sdhci-acpi: Allow changing HS200/HS400 driver strength for AMDI0040
- sdhci-esdhc-imx: Convert the driver to DT-only
- sdhci-pci-gli: Improve performance for HS400 mode for GL9763E
- sdhci-pci-gli: Reduce power consumption for GL9755
- sdhci-xenon: Introduce ACPI support
- tmio: Fix command error processing
- tmio: Inform the core about the max_busy_timeout
- tmio/renesas_sdhi: Support custom calculation of busy-wait time
- renesas_sdhi: Reset SCC only when available
- rtsx_pci: Add SD Express mode support for RTS5261
- rtsx_pci: Various fixes and improvements for RTS5261
MEMSTICK:
- Minor fixes/improvements.
-----BEGIN PGP SIGNATURE-----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=1A/T
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Initial support for SD express card/host
MMC host:
- mxc: Convert the driver to DT-only
- mtk-sd: Add HS400 enhanced strobe support
- mtk-sd: Add support for the MT8192 SoC variant
- sdhci-acpi: Allow changing HS200/HS400 driver strength for AMDI0040
- sdhci-esdhc-imx: Convert the driver to DT-only
- sdhci-pci-gli: Improve performance for HS400 mode for GL9763E
- sdhci-pci-gli: Reduce power consumption for GL9755
- sdhci-xenon: Introduce ACPI support
- tmio: Fix command error processing
- tmio: Inform the core about the max_busy_timeout
- tmio/renesas_sdhi: Support custom calculation of busy-wait time
- renesas_sdhi: Reset SCC only when available
- rtsx_pci: Add SD Express mode support for RTS5261
- rtsx_pci: Various fixes and improvements for RTS5261
MEMSTICK:
- Minor fixes/improvements"
* tag 'mmc-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (72 commits)
dt-bindings: mmc: eliminate yamllint warnings
mmc: sdhci-xenon: introduce ACPI support
mmc: sdhci-xenon: use clk only with DT
mmc: sdhci-xenon: switch to device_* API
mmc: sdhci-xenon: use match data for controllers variants
dt-bindings: mmc: Fix xlnx,mio-bank property values for arasan driver
mmc: renesas_sdhi: populate hook for longer busy_wait
mmc: tmio: add hook for custom busy_wait calculation
mmc: tmio: set max_busy_timeout
dt-bindings: mmc: imx: fix the wrongly dropped imx8qm compatible string
mmc: sdhci-pci-gli: Disable slow mode in HS400 mode for GL9763E
mmc: sdhci: Use more concise device_property_read_u64
memstick: r592: Fix error return in r592_probe()
mmc: mxc: Convert the driver to DT-only
mmc: mxs: Remove the unused .id_table
mmc: sdhci-of-arasan: Fix fall-through warnings for Clang
mmc: sdhci-pci-gli: Reduce power consumption for GL9755
mmc: mediatek: depend on COMMON_CLK to fix compile tests
mmc: pxamci: Fix error return code in pxamci_probe
mmc: sdhci: Update firmware interface API
...
Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be more
and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iDZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRMACgqxKS2CUcY8tPnR5weHEsbz6O+KAAn3BtEFnK
7V9EnSuZe4L1jNOHOB5V
=xzHh
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
Previous patches dropped the strict dependency on the OF_*
in the sdhci-xenon driver. As a result the ACPI support
can be introduced (except for the XENON_A3700 variant)
by adding the necessary ID's in the acpi_match_table.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-5-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a preparation for supporting ACPI, modify the driver
to use the clk framework only when booting with DT -
otherwise rely on the configuration done by firmware.
For that purpose introduce also a custom SDHCI get_max_clock
callback.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-4-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to support both ACPI and DT, modify the driver
to use device_* routines for obtaining the properties
values.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-3-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a part of the ACPI support preparation resign from checking
compatible strings in the driver. Instead of that use a new
enum and assign the values to match data accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-2-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
rtsx_pcr:
add callback functions to support runtime PM
add delay_work to put device to D3 after idle
over 10 sec
rts5249:
add extra init flow for rtd3 and set rtd3_en from
config setting
rtsx_pci_sdmmc:
child device support autosuspend
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20201202065857.19412-1-ricky_wu@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef check for the suspend/resume functions is wrong:
drivers/mmc/host/mtk-sd.c:2765:12: error: unused function 'msdc_suspend' [-Werror,-Wunused-function]
static int msdc_suspend(struct device *dev)
drivers/mmc/host/mtk-sd.c:2779:12: error: unused function 'msdc_resume' [-Werror,-Wunused-function]
static int msdc_resume(struct device *dev)
Remove the #ifdef and mark all four as __maybe_unused to aovid the
problem.
Fixes: c0a2074ac5 ("mmc: mediatek: Fix system suspend/resume support for CQHCI")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201203222922.1067522-1-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of the EXTOP bit in R-Car Gen3 SoCs to have a twice as large
busy wait duration.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Newer SDHI variants can 'wait while busy' longer than the generic TMIO.
Provide a hook to get the maximum cycle count to wait for. If the hook
is not populated, fall back to a generic version which works well with
all older TMIO/SDHI variants.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set max_busy_timeouts for variants known to support the TOPxx bits in
the SD_OPTION register. The timeout mechanism was running in the
background but not yet properly handled in the driver. So, let the MMC
core know when to not use R1B to avoid unhandled timeouts.
My datasheets for older variants (tmio_mmc.c) suggest that they support
it, too. However, actual bit descriptions are lacking, so I chose an
opt-in approach.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Further testing of error cases revealed that downgrade is not enough, so
we need to reset the SCC which is done by calling the custom reset
function. This reset function can distinguish between the various SDHI
variants, so protecting the call with MIN_RCAR2 is enough here.
Fixes: 24ce2d7b8b ("mmc: tmio: bring tuning HW to a sane state with MMC_POWER_OFF")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125204953.3344-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The GL9763E uses 150Mhz (slow mode) by default in HS400 mode. In order
to make HS400 mode run at 200Mhz, the slow mode needs to be turned off.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20201125110145.2824-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since we only need a single u64 the _array form is
unnecessarily. Use device_property_read_u64 instead.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201125033630.603863-1-jeremy.linton@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201123203004.18792-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mxs-mmc driver is only used by DT platforms and the .id_table
is unused.
Get rid of it to simplify the code.
While at it, use of_device_get_match_data() to retrieve the driver
data.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201123191956.10542-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For GL9755, reduce power consumption by lowering the LFCLK and disabling
the DMACLK on low-power.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20201123053702.6083-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MFD_OMAP_USB_HOST uses Common Clock Framework thus it cannot be
built on platforms without it (e.g. compile test on MIPS with LANTIQ):
mips-linux-ld: drivers/mmc/host/mtk-sd.o: in function `msdc_ops_set_ios':
mtk-sd.c:(.text+0x2bbc): undefined reference to `clk_get_parent'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201122120056.100045-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return the error code from devm_gpiod_get_optional() instaed
of 0 in pxamci_probe().
Fixes: f54005b508 ("mmc: pxa: Use GPIO descriptor for power")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Link: https://lore.kernel.org/r/20201121021431.3168506-1-chengzhihao1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
