On the imx51_3ds board, eCSPI2 is connected to a SPI NOR flash,
now add iomux definitions for those used pins.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The driver recently learned to handle platform ids. Make use of this
new feature. The up side is that the driver needs less knowledge about
the spi interfaces used on different SoCs.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX51 comes with two eCSPI interfaces (that are quite different from
what was known before---the tried and tested Freescale way) and a CSPI
interface that is identical to the devices found on i.MX25 and i.MX35.
This patch is a merge of two very similar patches (by Jason Wang and Sascha
Hauer resp.) plus a (now hopefully correct) reimplementation of the
clock calculation.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This prepares adding support for imx51's eCSPI. This IP has seperate
control and config bits for all four supported chip selects, so the
config routine needs to know which chip select is being used even if
the chipselect is realized by a gpio.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Nearly everything that is needed is provided by the version of the SPI IP.
Now the only checks left using cpu_is_... are clk divider tuning on mx21/mx27
and autodetection (which will die soon).
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This has the advantage not to need to much cpu_is_... macros. Still more
when imx51 support is added which has two different spi interfaces which
would introduce additional checks on the device id.
With this setup it's not possible for the compiler anymore to detect the
unused functions, so four additional kconfig symbols are introduced to
ifdef out the unneeded functions in the callback array and all these
functions are marked with __maybe_unused to suppress the corresponding
gcc warnings.
Comparing the driver footprint with and without the patch for a mx27
kernel yields:
add/remove: 2/0 grow/shrink: 2/0 up/down: 280/0 (280)
function old new delta
spi_imx_devtype - 192 +192
spi_imx_probe 980 1032 +52
spi_imx_devtype_data - 32 +32
spi_imx_setupxfer 276 280 +4
Later when the platform code is updated to use the platform ids, the
autodetection can be removed which will make the driver a bit smaller
again. (~60 Bytes in my test.)
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Group soc specific data in a global struct instead of repeating it for
each call to imxXX_add_spi_imxX. The structs holding the actual data
are placed in .init.constdata and so don't do much harm. Compared to
the previous approach this reduces code size to call imx_add_spi_imx.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The names used now match the processor's reference manual. Also remove
MXC from the interrupt defines to match the other imx platforms.
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This makes the header more look like the other ones, i.e.
- sort #defines by value
- use lowercase hex constants
- use a consistently named header guard
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Further remove FIXED_PHY as it breaks the ethernet.
VGA_CONSOLE isn't selectable anymore since fb78b51cb1.
EXT3_DEFAULTS_TO_ORDERED defaults to y since aa32a79638.
INOTIFY is gone since 2dfc1cae4c.
CONFIG_DETECT_SOFTLOCKUP is gone since e16bb1d7fe.
Enable TMPFS for udev.
KEYS is selected by NFS_USE_KERNEL_DNS
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This machine is enabled in mx3_defconfig and so mx31pdk_defconfig isn't
really useful.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- enable all mx27 machines (MACH_CPUIMX27, MACH_IMX27_VISSTRIM_M10,
MACH_PCA100, MACH_MXT_TD60) including optional features for
CPUIMX27
- eukrea_mbimx27-baseboard.c uses TOUCHSCREEN_ADS7846
- mach-cpuimx27.c uses SERIAL_8250
- several machines make use of SPI_IMX (selects SPI_BITBANG)
- drop VGA_CONSOLE as this isn't selectable anymore since fb78b51cb1
- several machines make use of USB_ULPI (depends on USB, but don't
enable USB_DEVICE_CLASS as it's deprecated)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This fixes:
arch/arm/plat-mxc/ehci.c: In function 'mxc_initialize_usb_hw':
arch/arm/plat-mxc/ehci.c:260: warning: assignment makes integer from pointer without a cast
arch/arm/plat-mxc/ehci.c:263: warning: assignment makes integer from pointer without a cast
arch/arm/plat-mxc/ehci.c:270: warning: assignment makes integer from pointer without a cast
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The flexcan driver was merged as e955cead.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested it by booting a rootfs via NFS.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The Enhanced Periodic Interrupt Timer (EPIT) is found on newer
i.MX SoCs and can be used as an alternative system timer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
we still have to toggle two pins on the mc9sdz60:
/* MUX3_CTR to be low for USB Host2 DP&DM */
pmic_gpio_set_bit_val(MCU_GPIO_REG_GPIO_CONTROL_2, 6, 0);
/* CAN_PWDN to be high for USB Host2 Power&OC */
pmic_gpio_set_bit_val(MCU_GPIO_REG_GPIO_CONTROL_2, 1, 1);
until we've a proper driver for the mx9sdz60 in linux we'll do this in
barebox (a.k.a. u-boot-v2)
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Rename the variable holding the usb otg platform data to avoid clash
with usb host platform data variable.
usb_pdata -> usb_otg_pdata
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The mx35_3ds comes with 2 GiByte NAND flash. This adds the
corresponding platform device.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The mx35_3ds comes with 64 MiByte for NOR flash at CS0, add physmap-flash
platform device for it.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Vista Silicon Visstrim_m10 i.MX27 based board is used
as multimedia streaming server, access control and other
custom applications.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fix docbook templates that reference files that do not contain the
expected kernel-doc notation.
Fixes these warnings:
Warning(arch/x86/include/asm/unaligned.h): no structured comments found
Warning(lib/vsprintf.c): no structured comments found
These cause errors in the generated html output, like below, so drop
these lines.
Name
arch/x86/include/asm/unaligned.h - Document generation inconsistency
Oops
Warning
The template for this document tried to insert the structured comment from the file arch/x86/include/asm/unaligned.h at this point, but none was found. This dummy section is inserted to allow generation to continue.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When you don't use !E or !I but only !F, then it's very easy to miss
including some functions, structs etc. in documentation. To help
finding which ones were missed, allow printing out the unused ones as
warnings.
For example, using this on mac80211 yields a lot of warnings like this:
Warning: didn't use docs for DOC: mac80211 workqueue
Warning: didn't use docs for ieee80211_max_queues
Warning: didn't use docs for ieee80211_bss_change
Warning: didn't use docs for ieee80211_bss_conf
when generating the documentation for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are valid attributes that could have upper case letters, but we
still want to remove, like for example
__attribute__((aligned(NETDEV_ALIGN)))
as encountered in the wireless code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a problem in hibernate_preallocate_memory() that it calls
preallocate_image_memory() with an argument that may be greater than
the total number of available non-highmem memory pages. If that's
the case, the OOM condition is guaranteed to trigger, which in turn
can cause significant slowdown to occur during hibernation.
To avoid that, make preallocate_image_memory() adjust its argument
before calling preallocate_image_pages(), so that the total number of
saveable non-highem pages left is not less than the minimum size of
a hibernation image. Change hibernate_preallocate_memory() to try to
allocate from highmem if the number of pages allocated by
preallocate_image_memory() is too low.
Modify free_unnecessary_pages() to take all possible memory
allocation patterns into account.
Reported-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: M. Vefa Bicakci <bicave@superonline.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (28 commits)
ipheth: remove incorrect devtype to WWAN
MAINTAINERS: Add CAIF
sctp: fix test for end of loop
KS8851: Correct RX packet allocation
udp: add rehash on connect()
net: blackhole route should always be recalculated
ipv4: Suppress lockdep-RCU false positive in FIB trie (3)
niu: Fix kernel buffer overflow for ETHTOOL_GRXCLSRLALL
ipvs: fix active FTP
gro: Re-fix different skb headrooms
via-velocity: Turn scatter-gather support back off.
ipv4: Fix reverse path filtering with multipath routing.
UNIX: Do not loop forever at unix_autobind().
PATCH: b44 Handle RX FIFO overflow better (simplified)
irda: off by one
3c59x: Fix deadlock in vortex_error()
netfilter: discard overlapping IPv6 fragment
ipv6: discard overlapping fragment
net: fix tx queue selection for bridged devices implementing select_queue
bonding: Fix jiffies overflow problems (again)
...
Fix up trivial conflicts due to the same cgroup API thinko fix going
through both Andrew and the networking tree. However, there were small
differences between the two, with Andrew's version generally being the
nicer one, and the one I merged first. So pick that one.
Conflicts in: include/linux/cgroup.h and kernel/cgroup.c
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, tsc: Fix a preemption leak in restore_sched_clock_state()
sched: Move sched_avg_update() to update_cpu_load()
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: don't enable self-refresh on Ironlake
drm/i915: Double check that the wait_request is not pending before warning
Revert "drm/i915: Warn if we run out of FIFO space for a mode"
Revert "drm/i915: Allow LVDS on pipe A on gen4+"
Revert "drm/i915: Enable RC6 on Ironlake."
A real life genuine preemption leak..
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
