Stuart Hayes reports that an error handled by DPC at a Root Port results
in pciehp gratuitously bringing down a subordinate hotplug port:
RP -- UP -- DP -- UP -- DP (hotplug) -- EP
pciehp brings the slot down because the Link to the Endpoint goes down.
That is caused by a Hot Reset being propagated as a result of DPC.
Per PCIe Base Spec 5.0, section 6.6.1 "Conventional Reset":
For a Switch, the following must cause a hot reset to be sent on all
Downstream Ports: [...]
* The Data Link Layer of the Upstream Port reporting DL_Down status.
In Switches that support Link speeds greater than 5.0 GT/s, the
Upstream Port must direct the LTSSM of each Downstream Port to the
Hot Reset state, but not hold the LTSSMs in that state. This permits
each Downstream Port to begin Link training immediately after its
hot reset completes. This behavior is recommended for all Switches.
* Receiving a hot reset on the Upstream Port.
Once DPC recovers, pcie_do_recovery() walks down the hierarchy and
invokes pcie_portdrv_slot_reset() to restore each port's config space.
At that point, a hotplug interrupt is signaled per PCIe Base Spec r5.0,
section 6.7.3.4 "Software Notification of Hot-Plug Events":
If the Port is enabled for edge-triggered interrupt signaling using
MSI or MSI-X, an interrupt message must be sent every time the logical
AND of the following conditions transitions from FALSE to TRUE: [...]
* The Hot-Plug Interrupt Enable bit in the Slot Control register is
set to 1b.
* At least one hot-plug event status bit in the Slot Status register
and its associated enable bit in the Slot Control register are both
set to 1b.
Prevent pciehp from gratuitously bringing down the slot by clearing the
error-induced Data Link Layer State Changed event before restoring
config space. Afterwards, check whether the link has unexpectedly
failed to retrain and synthesize a DLLSC event if so.
Allow each pcie_port_service_driver (one of them being pciehp) to define
a slot_reset callback and re-use the existing pm_iter() function to
iterate over the callbacks.
Thereby, the Endpoint driver remains bound throughout error recovery and
may restore the device to working state.
Surprise removal during error recovery is detected through a Presence
Detect Changed event. The hotplug port is expected to not signal that
event as a result of a Hot Reset.
The issue isn't DPC-specific, it also occurs when an error is handled by
AER through aer_root_reset(). So while the issue was noticed only now,
it's been around since 2006 when AER support was first introduced.
[bhelgaas: drop PCI_ERROR_RECOVERY Kconfig, split pm_iter() rename to
preparatory patch]
Link: https://lore.kernel.org/linux-pci/08c046b0-c9f2-3489-eeef-7e7aca435bb9@gmail.com/
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Link: https://lore.kernel.org/r/251f4edcc04c14f873ff1c967bc686169cd07d2d.1627638184.git.lukas@wunner.de
Reported-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.19+: ba952824e6: PCI/portdrv: Report reset for frozen channel
Cc: Keith Busch <kbusch@kernel.org>
Some AMD GPUs have built-in USB xHCI and USB Type-C UCSI controllers with
power dependencies between the GPU and the other functions as in
6d2e369f0d ("PCI: Add NVIDIA GPU multi-function power dependencies").
Add device link support for the AMD integrated USB xHCI and USB Type-C UCSI
controllers.
Without this, runtime power management, including GPU resume and temp and
fan sensors don't work correctly.
Reported-at: https://gitlab.freedesktop.org/drm/amd/-/issues/1704
Link: https://lore.kernel.org/r/20210903063311.3606226-1-evan.quan@amd.com
Signed-off-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Commit 375553a932 ("PCI: Setup ACPI fwnode early and at the same time
with OF") added a call to pci_set_acpi_fwnode() in pci_setup_device(),
which unconditionally clears any fwnode previously set by
pci_set_of_node().
pci_set_acpi_fwnode() looks for ACPI_COMPANION(), which only returns the
existing fwnode if it was set by ACPI_COMPANION_SET(). If it was set by
OF instead, ACPI_COMPANION() returns NULL and pci_set_acpi_fwnode()
accidentally clears the fwnode. To fix this, look for any fwnode instead
of just ACPI companions.
Fixes a virtio-iommu boot regression in v5.15-rc1.
Fixes: 375553a932 ("PCI: Setup ACPI fwnode early and at the same time with OF")
Link: https://lore.kernel.org/r/20210913172358.1775381-1-jean-philippe@linaro.org
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
7bac54497c ("PCI/VPD: Determine VPD size in pci_vpd_init()") reads VPD at
enumeration-time to find the size. But this is quite slow, and we don't
need the size until we actually need data from VPD. Dave reported a boot
slowdown of more than two minutes [1].
Defer the VPD sizing until a driver or the user (via sysfs) requests
information from VPD.
If devices are quirked because VPD is known not to work, don't bother even
looking for the VPD capability. The VPD will not be accessible at all.
[1] https://lore.kernel.org/r/20210913141818.GA27911@codemonkey.org.uk/
Link: https://lore.kernel.org/r/20210914215543.GA1437800@bjorn-Precision-5520
Fixes: 7bac54497c ("PCI/VPD: Determine VPD size in pci_vpd_init()")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Add ACPI support to the PCI VMD driver (Rafael Wysocki).
- Rearrange suspend-to-idle support code to reflect the platform
firmware expectations on some AMD platforms (Mario Limonciello).
- Make SSDT overlays documentation follow the code documented by it
more closely (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAmE41EgSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxZrgP/iStcM1PdEkzW9KInTbI7MDiQl8Iaem2
4AcbrsQmJxAEfJ+kzUuoArjj+y4T8sf49AA9Akg/q3zwf0oBix8JdtPDEx823oG8
7/0zjPJMigmcmGfGIlnQaSYqE30hatsthqF0iyH9AZjRzM1m9MavAtxrwDOD0Chq
m6kMObNorm/C0mjdPy71DAbiPbrcsMTFjw27hXHWnfsQFhZeVAoyhh2aFvk790pG
QRxpArI8r3dLb9vORQWo0q4jezPrRU6HzfvULVZEtv5+F8VUAby+qi1oGUSNx6CX
OB20Z1MFPSolsJvyRkfE8HEq0x1Es37doBROolhmliaKUQezwKPMZKJGgEYyUaSJ
bnWmN2wuE39VB6rIWXIaw6bHX3RwWnUJgoMvTZZIexp4kmmy9nsPB119na2odFVW
D06yMPZwx9lCDVWNkIbpcCGHkBWvQSZ+X/tROVOgyutJ2Rgph0PTVxQxVZmTnTWm
Pq6Tp8lSeatL16vEY75EX5pXbmKiGDIFrGv28Jxou2Arf31hcagY+rxu6YYORefu
NdkC2GD4TlQMGm2Ukfo5D/svFzJ/MQvP75ytVP3Oqi7ZFLkU2RzYOun8oOcZjUk6
76CH5/fmSvV2NbZRCDzhxiDXVhBFPaGm0KFnYYKs1V7AskdhnzOkd03z2bseTC0V
XNk0fHL1R38J
=8lPe
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These add ACPI support to the PCI VMD driver, improve suspend-to-idle
support for AMD platforms and update documentation.
Specifics:
- Add ACPI support to the PCI VMD driver (Rafael Wysocki)
- Rearrange suspend-to-idle support code to reflect the platform
firmware expectations on some AMD platforms (Mario Limonciello)
- Make SSDT overlays documentation follow the code documented by it
more closely (Andy Shevchenko)"
* tag 'acpi-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Run both AMD and Microsoft methods if both are supported
Documentation: ACPI: Align the SSDT overlays file with the code
PCI: VMD: ACPI: Make ACPI companion lookup work for VMD bus
Pull swiotlb updates from Konrad Rzeszutek Wilk:
"A new feature called restricted DMA pools. It allows SWIOTLB to
utilize per-device (or per-platform) allocated memory pools instead of
using the global one.
The first big user of this is ARM Confidential Computing where the
memory for DMA operations can be set per platform"
* 'stable/for-linus-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb: (23 commits)
swiotlb: use depends on for DMA_RESTRICTED_POOL
of: restricted dma: Don't fail device probe on rmem init failure
of: Move of_dma_set_restricted_buffer() into device.c
powerpc/svm: Don't issue ultracalls if !mem_encrypt_active()
s390/pv: fix the forcing of the swiotlb
swiotlb: Free tbl memory in swiotlb_exit()
swiotlb: Emit diagnostic in swiotlb_exit()
swiotlb: Convert io_default_tlb_mem to static allocation
of: Return success from of_dma_set_restricted_buffer() when !OF_ADDRESS
swiotlb: add overflow checks to swiotlb_bounce
swiotlb: fix implicit debugfs declarations
of: Add plumbing for restricted DMA pool
dt-bindings: of: Add restricted DMA pool
swiotlb: Add restricted DMA pool initialization
swiotlb: Add restricted DMA alloc/free support
swiotlb: Refactor swiotlb_tbl_unmap_single
swiotlb: Move alloc_size to swiotlb_find_slots
swiotlb: Use is_swiotlb_force_bounce for swiotlb data bouncing
swiotlb: Update is_swiotlb_active to add a struct device argument
swiotlb: Update is_swiotlb_buffer to add a struct device argument
...
- Fix dma-valid return WAITED implementation (Anthony Yznaga)
- SPDX license cleanups (Cai Huoqing)
- Split vfio-pci-core from vfio-pci and enhance PCI driver matching
to support future vendor provided vfio-pci variants (Yishai Hadas,
Max Gurtovoy, Jason Gunthorpe)
- Replace duplicated reflck with core support for managing first
open, last close, and device sets (Jason Gunthorpe, Max Gurtovoy,
Yishai Hadas)
- Fix non-modular mdev support and don't nag about request callback
support (Christoph Hellwig)
- Add semaphore to protect instruction intercept handler and replace
open-coded locks in vfio-ap driver (Tony Krowiak)
- Convert vfio-ap to vfio_register_group_dev() API (Jason Gunthorpe)
-----BEGIN PGP SIGNATURE-----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=nzK7
-----END PGP SIGNATURE-----
Merge tag 'vfio-v5.15-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Fix dma-valid return WAITED implementation (Anthony Yznaga)
- SPDX license cleanups (Cai Huoqing)
- Split vfio-pci-core from vfio-pci and enhance PCI driver matching to
support future vendor provided vfio-pci variants (Yishai Hadas, Max
Gurtovoy, Jason Gunthorpe)
- Replace duplicated reflck with core support for managing first open,
last close, and device sets (Jason Gunthorpe, Max Gurtovoy, Yishai
Hadas)
- Fix non-modular mdev support and don't nag about request callback
support (Christoph Hellwig)
- Add semaphore to protect instruction intercept handler and replace
open-coded locks in vfio-ap driver (Tony Krowiak)
- Convert vfio-ap to vfio_register_group_dev() API (Jason Gunthorpe)
* tag 'vfio-v5.15-rc1' of git://github.com/awilliam/linux-vfio: (37 commits)
vfio/pci: Introduce vfio_pci_core.ko
vfio: Use kconfig if XX/endif blocks instead of repeating 'depends on'
vfio: Use select for eventfd
PCI / VFIO: Add 'override_only' support for VFIO PCI sub system
PCI: Add 'override_only' field to struct pci_device_id
vfio/pci: Move module parameters to vfio_pci.c
vfio/pci: Move igd initialization to vfio_pci.c
vfio/pci: Split the pci_driver code out of vfio_pci_core.c
vfio/pci: Include vfio header in vfio_pci_core.h
vfio/pci: Rename ops functions to fit core namings
vfio/pci: Rename vfio_pci_device to vfio_pci_core_device
vfio/pci: Rename vfio_pci_private.h to vfio_pci_core.h
vfio/pci: Rename vfio_pci.c to vfio_pci_core.c
vfio/ap_ops: Convert to use vfio_register_group_dev()
s390/vfio-ap: replace open coded locks for VFIO_GROUP_NOTIFY_SET_KVM notification
s390/vfio-ap: r/w lock for PQAP interception handler function pointer
vfio/type1: Fix vfio_find_dma_valid return
vfio-pci/zdev: Remove repeated verbose license text
vfio: platform: reset: Convert to SPDX identifier
vfio: Remove struct vfio_device_ops open/release
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYTB6pAAKCRCAXGG7T9hj
vk9xAP9hUQtGdTb5eW9+3X3PHDON2jGbydAMtQ57WJLdqj0oFgD/cGV95PKv0jgg
zgw6Icf9Vp6APF/Ucd/dOB0B6qviJgw=
=PNRc
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- some small cleanups
- a fix for a bug when running as Xen PV guest which could result in
not all memory being transferred in case of a migration of the guest
- a small series for getting rid of code for supporting very old Xen
hypervisor versions nobody should be using since many years now
- a series for hardening the Xen block frontend driver
- a fix for Xen PV boot code issuing warning messages due to a stray
preempt_disable() on the non-boot processors
* tag 'for-linus-5.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: remove stray preempt_disable() from PV AP startup code
xen/pcifront: Removed unnecessary __ref annotation
x86: xen: platform-pci-unplug: use pr_err() and pr_warn() instead of raw printk()
drivers/xen/xenbus/xenbus_client.c: fix bugon.cocci warnings
xen/blkfront: don't trust the backend response data blindly
xen/blkfront: don't take local copy of a request from the ring page
xen/blkfront: read response from backend only once
xen: assume XENFEAT_gnttab_map_avail_bits being set for pv guests
xen: assume XENFEAT_mmu_pt_update_preserve_ad being set for pv guests
xen: check required Xen features
xen: fix setting of max_pfn in shared_info
- Add max-virtual-functions to endpoint binding (Kishon Vijay Abraham I)
- Add pci_epf_add_vepf() API to add virtual function to endpoint (Kishon
Vijay Abraham I)
- Add pci_epf_vepf_link() to link virtual function to endpoint physical
function (Kishon Vijay Abraham I)
- Add virtual function number to pci_epc_ops endpoint ops interfaces
(Kishon Vijay Abraham I)
- Simplify register base address computation for endpoint BAR configuration
(Kishon Vijay Abraham I)
- Add support to configure virtual functions in cadence endpoint driver
(Kishon Vijay Abraham I)
- Add SR-IOV configuration to endpoint test driver (Kishon Vijay Abraham I)
- Document configfs usage to create virtual functions for endpoints (Kishon
Vijay Abraham I)
* remotes/lorenzo/pci/endpoint:
Documentation: PCI: endpoint/pci-endpoint-cfs: Guide to use SR-IOV
misc: pci_endpoint_test: Populate sriov_configure ops to configure SR-IOV device
PCI: cadence: Add support to configure virtual functions
PCI: cadence: Simplify code to get register base address for configuring BAR
PCI: endpoint: Add virtual function number in pci_epc ops
PCI: endpoint: Add support to link a physical function to a virtual function
PCI: endpoint: Add support to add virtual function in endpoint core
dt-bindings: PCI: pci-ep: Add binding to specify virtual function
- Fix runtime PM imbalance in rcar_pcie_ep_probe() (Dinghao Liu)
* remotes/lorenzo/pci/rcar:
PCI: rcar: Add L1 link state fix into data abort hook
PCI: rcar: Fix runtime PM imbalance in rcar_pcie_ep_probe()
- Split DT bindings for PCIe controllers with independent MSI domains into
separate nodes for MT2712/MT7622 (Chuanjia Liu)
- Locate shared registers from "mediatek,generic-pciecfg" property
(Chuanjia Liu)
- Get IRQ from "pcie_irq" if "interrupt-names" property is present to fix
an MSI issue (Chuanjia Liu)
- Get PCI domain from "linux,pci-domain" property if present (Chuanjia Liu)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Use PCI domain to handle ports detection
PCI: mediatek: Add new method to get irq number
PCI: mediatek: Add new method to get shared pcie-cfg base address
dt-bindings: PCI: mediatek: Update the Device tree bindings
- Add domain_nr in struct pci_host_bridge (Boqun Feng)
- Use host bridge MSI domain for root buses if present (Boqun Feng)
- Allow ARM64 virtual host bridge with no ACPI companion (e.g., Hyper-V)
(Boqun Feng)
- Make Hyper-V enumeration more generic (Arnd Bergmann)
- Set Hyper-V domain_nr at probe-time (Boqun Feng)
- Set up Hyper-V MSI domain at bridge probe-time (Boqun Feng)
- Enable Hyper-V bridge probing on ARM64 (Boqun Feng)
* remotes/lorenzo/pci/hyper-v:
PCI: hv: Turn on the host bridge probing on ARM64
PCI: hv: Set up MSI domain at bridge probing time
PCI: hv: Set ->domain_nr of pci_host_bridge at probing time
PCI: hv: Generify PCI probing
arm64: PCI: Support root bridge preparation for Hyper-V
arm64: PCI: Restructure pcibios_root_bridge_prepare()
PCI: Support populating MSI domains of root buses via bridges
PCI: Introduce domain_nr in pci_host_bridge
- Convert bool in structs to bitfield (Kishon Vijay Abraham I)
- Work around J7200 non-PCIe SERDES lane electrical issue that prevents
PCIe link training (Nadeem Athani)
- Add J7200 PCIe support to j721e (Kishon Vijay Abraham I)
- Add AM64 PCIe support to j721e (Kishon Vijay Abraham I)
- Add J7200 and AM64 device IDs to endpoint test (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
misc: pci_endpoint_test: Add deviceID for AM64 and J7200
PCI: j721e: Add PCIe support for AM64
PCI: j721e: Add PCIe support for J7200
PCI: cadence: Add quirk flag to set minimum delay in LTSSM Detect.Quiet state
PCI: cadence: Use bitfield for *quirk_retrain_flag* instead of bool
- Fix PIO config access status checking (Evan Wang)
- Increase config access polling delay to 1.5s (Pali Rohár)
- Add PCIe Root Capabilities to bridge emulation (Pali Rohár)
- Report Config Request Retry Status when Software Visibility enabled (Pali
Rohár)
- Add back configuration of PCIe resources from 'ranges' DT property and
pay attention to DT size and CPU/PCI offset to fix issues with I/O port
space (Pali Rohár)
- Serialize masking and unmasking legacy INTx interrupts (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Fix masking and unmasking legacy INTx interrupts
PCI: aardvark: Configure PCIe resources from 'ranges' DT property
PCI: aardvark: Fix reporting CRS value
PCI: pci-bridge-emul: Add PCIe Root Capabilities Register
PCI: aardvark: Increase polling delay to 1.5s while waiting for PIO response
PCI: aardvark: Fix checking for PIO status
- Cache PCIe Device Capabilities register (Amey Narkhede)
- Add pcie_reset_flr() with 'probe' argument (Amey Narkhede)
- Add pdev->reset_methods[] array to track reset method ordering (Amey
Narkhede)
- Remove reset_fn field from pci_dev (Amey Narkhede)
- Add sysfs interface to query and set device reset mechanism (Amey
Narkhede)
- Add pci_set_acpi_fwnode() to set ACPI_COMPANION (Shanker Donthineni)
- Use acpi_pci_power_manageable() instead of duplicating logic (Shanker
Donthineni)
- Set ACPI fwnode early and at the same time with OF (Shanker Donthineni)
- Add support for ACPI _RST reset method (Shanker Donthineni)
- Change reset function 'probe' argument to bool (Amey Narkhede)
* pci/reset:
PCI: Change the type of probe argument in reset functions
PCI: Add support for ACPI _RST reset method
PCI: Setup ACPI fwnode early and at the same time with OF
PCI: Use acpi_pci_power_manageable()
PCI: Add pci_set_acpi_fwnode() to set ACPI_COMPANION
PCI: Allow userspace to query and set device reset mechanism
PCI: Remove reset_fn field from pci_dev
PCI: Add array to track reset method ordering
PCI: Add pcie_reset_flr() with 'probe' argument
PCI: Cache PCIe Device Capabilities register
- Enable Bandwidth Notification only if port supports it (Stuart Hayes)
* pci/portdrv:
PCI/portdrv: Enable Bandwidth Notification only if port supports it
ebda_rsrc_controller() calls iounmap(io_mem) on the error path. Its caller,
ibmphp_access_ebda(), also calls iounmap(io_mem) on good and error paths.
Remove the iounmap(io_mem) invocation from ebda_rsrc_controller().
[bhelgaas: remove item from TODO]
Link: https://lore.kernel.org/r/20210818165751.591185-1-os.vaslot@gmail.com
Signed-off-by: Vishal Aslot <os.vaslot@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On some systems, in order to get to the deepest low-power state of
the platform (which may be necessary to save significant enough
amounts of energy while suspended to idle. for example), devices on
the PCI bus exposed by the VMD driver need to be power-managed via
ACPI. However, the layout of the ACPI namespace below the VMD
controller device object does not reflect the layout of the PCI bus
under the VMD host bridge, so in order to identify the ACPI companion
objects for the devices on that bus, it is necessary to use a special
_ADR encoding on the ACPI side. In other words, acpi_pci_find_companion()
does not work for these devices, so it needs to be amended with a
special lookup logic specific to the VMD bus.
Address this issue by allowing the VMD driver to temporarily install
an ACPI companion lookup hook containing the code matching the devices
on the VMD PCI bus with the corresponding objects in the ACPI
namespace.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did the
following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
The latter one will cause a tiny merge issue with your tree, as there
was a last-minute fix for this in 5.14 in your tree, but the fixup
should be "obvious". If you want me to provide a fixed merge for this,
please let me know.
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs
users at once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+FLQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXuACfWECnysDtXNe66DdETCFs1a1RToYAoMokWeU5
s8VFP1NY2BjmxJbkebLL
=8kVu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
An unnecessary "__ref" annotation was removed from the
"drivers/pci/xen_pcifront.c" file. The function where the annotation
was used was "pcifront_backend_changed()", which does not call any
functions annotated as "__*init" nor "__*exit". This makes "__ref"
unnecessary since this annotation is used to make the compiler ignore
section miss-matches when they are not happening here in the first
place.
In addition to the aforementioned change, some code style issues were
fixed in the same file.
Signed-off-by: Sergio Miguéns Iglesias <sergio@lony.xyz>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20210830175305.13370-1-sergio@lony.xyz
Signed-off-by: Juergen Gross <jgross@suse.com>
- Enable memcg accounting for various networking objects.
BPF:
- Introduce bpf timers.
- Add perf link and opaque bpf_cookie which the program can read
out again, to be used in libbpf-based USDT library.
- Add bpf_task_pt_regs() helper to access user space pt_regs
in kprobes, to help user space stack unwinding.
- Add support for UNIX sockets for BPF sockmap.
- Extend BPF iterator support for UNIX domain sockets.
- Allow BPF TCP congestion control progs and bpf iterators to call
bpf_setsockopt(), e.g. to switch to another congestion control
algorithm.
Protocols:
- Support IOAM Pre-allocated Trace with IPv6.
- Support Management Component Transport Protocol.
- bridge: multicast: add vlan support.
- netfilter: add hooks for the SRv6 lightweight tunnel driver.
- tcp:
- enable mid-stream window clamping (by user space or BPF)
- allow data-less, empty-cookie SYN with TFO_SERVER_COOKIE_NOT_REQD
- more accurate DSACK processing for RACK-TLP
- mptcp:
- add full mesh path manager option
- add partial support for MP_FAIL
- improve use of backup subflows
- optimize option processing
- af_unix: add OOB notification support.
- ipv6: add IFLA_INET6_RA_MTU to expose MTU value advertised by
the router.
- mac80211: Target Wake Time support in AP mode.
- can: j1939: extend UAPI to notify about RX status.
Driver APIs:
- Add page frag support in page pool API.
- Many improvements to the DSA (distributed switch) APIs.
- ethtool: extend IRQ coalesce uAPI with timer reset modes.
- devlink: control which auxiliary devices are created.
- Support CAN PHYs via the generic PHY subsystem.
- Proper cross-chip support for tag_8021q.
- Allow TX forwarding for the software bridge data path to be
offloaded to capable devices.
Drivers:
- veth: more flexible channels number configuration.
- openvswitch: introduce per-cpu upcall dispatch.
- Add internet mix (IMIX) mode to pktgen.
- Transparently handle XDP operations in the bonding driver.
- Add LiteETH network driver.
- Renesas (ravb):
- support Gigabit Ethernet IP
- NXP Ethernet switch (sja1105)
- fast aging support
- support for "H" switch topologies
- traffic termination for ports under VLAN-aware bridge
- Intel 1G Ethernet
- support getcrosststamp() with PCIe PTM (Precision Time
Measurement) for better time sync
- support Credit-Based Shaper (CBS) offload, enabling HW traffic
prioritization and bandwidth reservation
- Broadcom Ethernet (bnxt)
- support pulse-per-second output
- support larger Rx rings
- Mellanox Ethernet (mlx5)
- support ethtool RSS contexts and MQPRIO channel mode
- support LAG offload with bridging
- support devlink rate limit API
- support packet sampling on tunnels
- Huawei Ethernet (hns3):
- basic devlink support
- add extended IRQ coalescing support
- report extended link state
- Netronome Ethernet (nfp):
- add conntrack offload support
- Broadcom WiFi (brcmfmac):
- add WPA3 Personal with FT to supported cipher suites
- support 43752 SDIO device
- Intel WiFi (iwlwifi):
- support scanning hidden 6GHz networks
- support for a new hardware family (Bz)
- Xen pv driver:
- harden netfront against malicious backends
- Qualcomm mobile
- ipa: refactor power management and enable automatic suspend
- mhi: move MBIM to WWAN subsystem interfaces
Refactor:
- Ambient BPF run context and cgroup storage cleanup.
- Compat rework for ndo_ioctl.
Old code removal:
- prism54 remove the obsoleted driver, deprecated by the p54 driver.
- wan: remove sbni/granch driver.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=JDGD
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Enable memcg accounting for various networking objects.
BPF:
- Introduce bpf timers.
- Add perf link and opaque bpf_cookie which the program can read out
again, to be used in libbpf-based USDT library.
- Add bpf_task_pt_regs() helper to access user space pt_regs in
kprobes, to help user space stack unwinding.
- Add support for UNIX sockets for BPF sockmap.
- Extend BPF iterator support for UNIX domain sockets.
- Allow BPF TCP congestion control progs and bpf iterators to call
bpf_setsockopt(), e.g. to switch to another congestion control
algorithm.
Protocols:
- Support IOAM Pre-allocated Trace with IPv6.
- Support Management Component Transport Protocol.
- bridge: multicast: add vlan support.
- netfilter: add hooks for the SRv6 lightweight tunnel driver.
- tcp:
- enable mid-stream window clamping (by user space or BPF)
- allow data-less, empty-cookie SYN with TFO_SERVER_COOKIE_NOT_REQD
- more accurate DSACK processing for RACK-TLP
- mptcp:
- add full mesh path manager option
- add partial support for MP_FAIL
- improve use of backup subflows
- optimize option processing
- af_unix: add OOB notification support.
- ipv6: add IFLA_INET6_RA_MTU to expose MTU value advertised by the
router.
- mac80211: Target Wake Time support in AP mode.
- can: j1939: extend UAPI to notify about RX status.
Driver APIs:
- Add page frag support in page pool API.
- Many improvements to the DSA (distributed switch) APIs.
- ethtool: extend IRQ coalesce uAPI with timer reset modes.
- devlink: control which auxiliary devices are created.
- Support CAN PHYs via the generic PHY subsystem.
- Proper cross-chip support for tag_8021q.
- Allow TX forwarding for the software bridge data path to be
offloaded to capable devices.
Drivers:
- veth: more flexible channels number configuration.
- openvswitch: introduce per-cpu upcall dispatch.
- Add internet mix (IMIX) mode to pktgen.
- Transparently handle XDP operations in the bonding driver.
- Add LiteETH network driver.
- Renesas (ravb):
- support Gigabit Ethernet IP
- NXP Ethernet switch (sja1105):
- fast aging support
- support for "H" switch topologies
- traffic termination for ports under VLAN-aware bridge
- Intel 1G Ethernet
- support getcrosststamp() with PCIe PTM (Precision Time
Measurement) for better time sync
- support Credit-Based Shaper (CBS) offload, enabling HW traffic
prioritization and bandwidth reservation
- Broadcom Ethernet (bnxt)
- support pulse-per-second output
- support larger Rx rings
- Mellanox Ethernet (mlx5)
- support ethtool RSS contexts and MQPRIO channel mode
- support LAG offload with bridging
- support devlink rate limit API
- support packet sampling on tunnels
- Huawei Ethernet (hns3):
- basic devlink support
- add extended IRQ coalescing support
- report extended link state
- Netronome Ethernet (nfp):
- add conntrack offload support
- Broadcom WiFi (brcmfmac):
- add WPA3 Personal with FT to supported cipher suites
- support 43752 SDIO device
- Intel WiFi (iwlwifi):
- support scanning hidden 6GHz networks
- support for a new hardware family (Bz)
- Xen pv driver:
- harden netfront against malicious backends
- Qualcomm mobile
- ipa: refactor power management and enable automatic suspend
- mhi: move MBIM to WWAN subsystem interfaces
Refactor:
- Ambient BPF run context and cgroup storage cleanup.
- Compat rework for ndo_ioctl.
Old code removal:
- prism54 remove the obsoleted driver, deprecated by the p54 driver.
- wan: remove sbni/granch driver"
* tag 'net-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1715 commits)
net: Add depends on OF_NET for LiteX's LiteETH
ipv6: seg6: remove duplicated include
net: hns3: remove unnecessary spaces
net: hns3: add some required spaces
net: hns3: clean up a type mismatch warning
net: hns3: refine function hns3_set_default_feature()
ipv6: remove duplicated 'net/lwtunnel.h' include
net: w5100: check return value after calling platform_get_resource()
net/mlxbf_gige: Make use of devm_platform_ioremap_resourcexxx()
net: mdio: mscc-miim: Make use of the helper function devm_platform_ioremap_resource()
net: mdio-ipq4019: Make use of devm_platform_ioremap_resource()
fou: remove sparse errors
ipv4: fix endianness issue in inet_rtm_getroute_build_skb()
octeontx2-af: Set proper errorcode for IPv4 checksum errors
octeontx2-af: Fix static code analyzer reported issues
octeontx2-af: Fix mailbox errors in nix_rss_flowkey_cfg
octeontx2-af: Fix loop in free and unmap counter
af_unix: fix potential NULL deref in unix_dgram_connect()
dpaa2-eth: Replace strlcpy with strscpy
octeontx2-af: Use NDC TX for transmit packet data
...
After recent introduction of new VPD API functions and user migration
these defines and inline functions aren't used outside VPD core any
longer.
Link: https://lore.kernel.org/r/d33e06bf-bc5e-ece7-bf35-7245ae224d1b@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a pci_vpd_find_id_string() API function to retrieve the ID string from
VPD.
This way callers don't need pci_vpd_lrdt_size() any longer, and it can be
made private to the VPD core.
Link: https://lore.kernel.org/r/c5225bf6-8d29-970d-e271-0d7b52252630@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pci_vpd_find_tag() post-processing from pci_vpd_find_ro_info_keyword()
to pci_vpd_find_tag(). This simplifies function pci_vpd_find_id_string()
that will be added in a subsequent patch.
Link: https://lore.kernel.org/r/fb15393f-d3b2-e140-2643-570d3abd7382@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that the last users have been migrated to pci_vpd_find_ro_keyword()
we can stop exporting this function. It's still used in VPD core code.
Link: https://lore.kernel.org/r/96ca2a56-383e-9b61-9cba-4f1e5611dc15@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that the last users have been migrated to pci_vpd_find_ro_keyword()
we can stop exporting this function. It's still used in VPD core code.
Link: https://lore.kernel.org/r/71131eca-0502-7878-365f-30b6614161cf@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Address 3 PCI device power management issues (Rafael Wysocki).
- Add Power Limit4 support for Alder Lake to the Intel RAPL power
capping driver (Sumeet Pawnikar).
- Add HWP guaranteed performance change notification support to
the intel_pstate driver (Srinivas Pandruvada).
- Replace deprecated CPU-hotplug functions in code related to power
management (Sebastian Andrzej Siewior).
- Update CPU PM notifiers to use raw spinlocks (Valentin Schneider).
- Add support for 'required-opps' DT property to the generic power
domains (genpd) framework and use this property for I2C on ARM64
sc7180 (Rajendra Nayak).
- Fix Kconfig issue related to genpd (Geert Uytterhoeven).
- Increase energy calculation precision in the Energy Model (Lukasz
Luba).
- Fix kobject deletion in the exit code of the schedutil cpufreq
governor (Kevin Hao).
- Unmark some functions as kernel-doc in the PM core to avoid
false-positive documentation build warnings (Randy Dunlap).
- Check RTC features instead of ops in suspend_test Alexandre
Belloni).
-----BEGIN PGP SIGNATURE-----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=sx6G
-----END PGP SIGNATURE-----
Merge tag 'pm-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These address some PCI device power management issues, add new
hardware support to the RAPL power capping driver, add HWP guaranteed
performance change notification support to the intel_pstate driver,
replace deprecated CPU-hotplug functions in a few places, update CPU
PM notifiers to use raw spinlocks, update the PM domains framework
(new DT property support, Kconfig fix), do a couple of cleanups in
code related to system sleep, and improve the energy model and the
schedutil cpufreq governor.
Specifics:
- Address 3 PCI device power management issues (Rafael Wysocki).
- Add Power Limit4 support for Alder Lake to the Intel RAPL power
capping driver (Sumeet Pawnikar).
- Add HWP guaranteed performance change notification support to the
intel_pstate driver (Srinivas Pandruvada).
- Replace deprecated CPU-hotplug functions in code related to power
management (Sebastian Andrzej Siewior).
- Update CPU PM notifiers to use raw spinlocks (Valentin Schneider).
- Add support for 'required-opps' DT property to the generic power
domains (genpd) framework and use this property for I2C on ARM64
sc7180 (Rajendra Nayak).
- Fix Kconfig issue related to genpd (Geert Uytterhoeven).
- Increase energy calculation precision in the Energy Model (Lukasz
Luba).
- Fix kobject deletion in the exit code of the schedutil cpufreq
governor (Kevin Hao).
- Unmark some functions as kernel-doc in the PM core to avoid
false-positive documentation build warnings (Randy Dunlap).
- Check RTC features instead of ops in suspend_test Alexandre
Belloni)"
* tag 'pm-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: domains: Fix domain attach for CONFIG_PM_OPP=n
powercap: Add Power Limit4 support for Alder Lake SoC
cpufreq: intel_pstate: Process HWP Guaranteed change notification
thermal: intel: Allow processing of HWP interrupt
notifier: Remove atomic_notifier_call_chain_robust()
PM: cpu: Make notifier chain use a raw_spinlock_t
PM: sleep: unmark 'state' functions as kernel-doc
arm64: dts: sc7180: Add required-opps for i2c
PM: domains: Add support for 'required-opps' to set default perf state
opp: Don't print an error if required-opps is missing
cpufreq: schedutil: Use kobject release() method to free sugov_tunables
PM: EM: Increase energy calculation precision
PM: sleep: check RTC features instead of ops in suspend_test
PM: sleep: s2idle: Replace deprecated CPU-hotplug functions
cpufreq: Replace deprecated CPU-hotplug functions
powercap: intel_rapl: Replace deprecated CPU-hotplug functions
PCI: PM: Enable PME if it can be signaled from D3cold
PCI: PM: Avoid forcing PCI_D0 for wakeup reasons inconsistently
PCI: Use pci_update_current_state() in pci_enable_device_flags()
HiSilicon KunPeng920 and KunPeng930 have devices that appear as PCI but are
actually on the AMBA bus. These fake PCI devices can support SVA via the
SMMU stall feature.
DT systems can indicate this in the device tree, but ACPI systems don't
have that mechanism, so add a "dma-can-stall" property manually for them.
[bhelgaas: add text from Robin as comment near quirk]
Link: https://lore.kernel.org/r/1626144876-11352-4-git-send-email-zhangfei.gao@linaro.org
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
