This patch adds a second tuple to reg property. The new property tuple
describes the memory location for data port registers mapped trough
L3 bus on am33xx. The both property tuples are named accordingly in
the reg-names property.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Populate nodes for l2-cache-controller, EDMA, mailbox,
mmc, sham.
Update as well DT properties for epwmss, aes, des.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Added dr_mode property in dwc3 and set its default mode to device.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
smps10 should be enabled only in the case of host mode. So stop
doing always_on, boot_on from smps10_out1. The driver will enable
it in host mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Do not reset GPIO1 at boot-up because GPIO 7 in GPIO1 block is used on
OMAP4460 PandaBoard-ES to select voltage register in TPS62361 which
supplies VDD_MPU.
Without this, OMAP4460 PandaBoard-ES boards fail to boot-up because
MPU voltage switches over to VSET0 voltage value (boot voltage) which
is not sufficient to operate the device at OPP100.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Do not reset GPIO0 at boot-up because GPIO0 is used
on AM335x EVM-SK to control VTT regulators on DDR3.
Without this EVM-SK boards fail to boot-up because
of DDR3 corruption.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
On OMAP we have co-processor IPs, memory controllers,
GPIOs which control regulators and power switches to
PMIC, and SoC internal Bus IPs, some or most of which
should either not be reset or idled or both at init.
(In some cases there are erratas which prevent an IP
from being reset)
Have a way to pass this information from DT.
Update the am33xx/omap4 and omap5 dtsi files with the
new bindings for modules which either should not be
idled. reset or both. A later patch would cleanup the
same information that exists today as part of the hwmod
data files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.
Fixes USB OTG port on GAT04 and N900 after the Generic PHY framework was
merged in greg/usb-next. [1]
[1] - https://lkml.org/lkml/2013/9/27/581
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The arm arch timers frequency are now programmed in the CNTFREQ
per-cpu register by the timer code using the secure API [1].
So remove the redundant entry from the dts.
[1] http://marc.info/?l=linux-omap&m=138139106312786&w=2
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=9Iuv
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to drop legacy booting support for some
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
* tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (125 commits)
ARM: OMAP2+: remove legacy support for IGEP boards
ARM: OMAP2+: Remove legacy support for zoom platforms
ARM: OMAP2+: Remove legacy booting support for omap3 EVM
ARM: OMAP2: delete board-rm680
ARM: dts: add minimal DT support for Nokia N950 & N9 phones
ARM: dts: Add basic support for zoom3
ARM: dts: Add basic support for TMDSEVM3730 (Mistral AM/DM37x EVM)
ARM: dts: Add common support for omap3-evm
ARM: dts: Shared file for omap GPMC connected smsc911x
+Linux 3.12-rc5
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add minimal DT support for Nokia N950 & N9 phones. The same functionality
that is provided by the current board file should work: serial console,
USB, OneNAND and MMC.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I've tested serial, MMC, smsc911x and wl12xx on zoom3. As my
omap is an early ES revision, I have not been able to test
off-idle on this one. But anyways, I'd say we have enough
device tree support for the zoom to be able to drop the
board-zoom files. Patches are welcome to add further features
to this .dts file.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The imx6sl iomuxc syscon is compatible to imx6q, so let's add
compatible string 'fsl,imx6q-iomuxc-gpr' for imx6sl iomuxc syscon node.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- addition of sound for at91sam9n12
- a little fix for MMC vs. SPI on at91sam9g20ek
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSYUtRAAoJEAf03oE53VmQH+EH/1YhBDF7uL5s+TCKLBOyau+G
i+W93uG4acZAdbUMRwY+/dP5HMwFu5ZSoKDD5LoRnG2O+jW5dB3rBPi1C42XRKa/
ra1wQcabKFPERJGDJ8DWbuLoJ7WNiDNENDa5ckV3m+F7dRbflcNyUB7vPUiGW78c
xe/WKCKB9Hhpytl1fAynRs+VEu/z3hW7KV7QFyVDatOtV11Vb4QSSJ5HjfMhfito
T7zAsML26hIdcNRsDQs8/4Uwgy8Tevl6FbtLHvht18BJB7FSxRtiPrAGh0KAmwsl
HwIT8RzgJqdDlXTi9z9BdLFlvFZkX83n12jrB7hGScOKav45kvmmC9pgwhFbRzk=
=uw6I
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
First DT series for 3.13
- addition of sound for at91sam9n12
- a little fix for MMC vs. SPI on at91sam9g20ek
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: remove pinctrl conflict between mmc and SPI for at91sam9g20ek
ARM: at91: add sound support on at91sam9n12ek board
ARM: at91: enable ssc on at91sam9n12ek board
ARM: at91: enable wm8904 on at91sam9n12ek board
ARM: at91: add ssc dma parameter for at91sam9n12
ARM: at91: add at91sam9n12 ssc clock in look up table
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- a little non-urgent fix
- addition of DT files to MAINTAINERS
- more important, the splitting of .dtsi files
that allows to precisely choose the peripherals
that are present for a particular SoC.
It is useful for upcoming move to common cloks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSYT2LAAoJEAf03oE53VmQfRMIAIgFQruxaCTlhpvdZaEyDeIK
6+szV0Nn9irQyZqe2HvUR6Flb7FfmAGiyS0xj/OY4bEBbCOeau8Df/op3fVa6+Q2
t510ricL9OWaSqaIsKgJqk3mjpq/7jMrXBQzBjQFgKVcJSA+zOJNiB6qabmE9KjY
z/2+hYaBgG7WwWffHmJQ34NYrIqrWbqaGZczxY9IVw7i4kfDXPL2t2JZk2JTwstt
4C4CRxKXx27EMF0gE2BOgH0r1euaqllSg4ogYlQkBn2canylvNYiRN2Eu36g4peE
cGjtW/8R0ngz3udeoQWeHZ+nZoFT15m048xgIOUbxX5Ocy7u7HSL0tbaH+W9ciI=
=VlMj
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
From Nicolas Ferre:
First cleanup series for 3.13
- a little non-urgent fix
- addition of DT files to MAINTAINERS
- more important, the splitting of .dtsi files
that allows to precisely choose the peripherals
that are present for a particular SoC.
It is useful for upcoming move to common cloks.
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91:
MAINTAINERS: Add patterns for DTS files for AT91
ARM: at91: remove init_machine() as default is suitable
ARM: at91/dt: split sama5d3 peripheral definitions
ARM: at91/dt: split sam9x5 peripheral definitions
ARM: at91: cam60: fix incorrect placement of __initdata tag
These MMC and SPI buses can't be configured at the same time because they
share the same traces on the EK board.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
From Heiko Stübner:
Support for the RK3188 SoC, basic RK3188 based Radxa Rock board
and RK3066a based BQ Curie2 tablet.
* rockchip/boards:
ARM: rockchip: add support for rk3188 and Radxa Rock board
ARM: rockchip: add dts for bqcurie2 tablet
ARM: rockchip: enable arm-global-timer
ARM: rockchip: move shared dt properties to common source file
This adds the SSP and SPI blocks to the device tree and makes
them active. Only this way can their clocks be properly gated
off at boot.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCLK for I2C4 is controlled by bit 10 in the PCKEN registers
while the KCLK is controlled by bit 9 on the KCKEN, it's
one of these odd assymetric things. Correct the PCLK bit to 10.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock assignment in the device tree for GPIO blocks 6
and 7 was incorrect, indicating this was managed by bit 1 on
PRCC 2 while it was in fact bit 11 on PRCC 2.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock assignment in the device tree for GPIO block 8 was
incorrect, indicating this was managed by bit 1 on PRCC 6
while it was in fact bit 1 on PRCC 5.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
add a pinctrl for ECSPI1. This pinctrl can be used in the imx6sl-evk board.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The pwm-node is missing its #pwm-cells property. The pwm-framework will
complain about this.
Add the missing property.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
From Stephen Warren:
* tegra/dt:
ARM: tegra: Use symbolic names for gr3d clocks
ARM: tegra: Mark Tegra30 display controller compatible with Tegra20
ARM: tegra: add GPIO controller to tegra124.dtsi
ARM: tegra: enable LP1 suspend mode for Venice2
ARM: tegra: enable Tegra RTC as default for Tegra124
ARM: tegra: add Venice2 board support
ARM: tegra: Add initial device tree for Tegra124
ARM: tegra: add vcc supply for nct1008 to Cardhu
ARM: tegra: add DT entry for nct1008 to Dalmore
ARM: tegra: use dt-binding header for key code
ARM: tegra: add palmas pincontrol to Dalmore device tree
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- convert Calxeda cpuidle driver to a platform driver and to use PSCI
- convert highbank smp_ops and suspend to PSCI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSYCG/AAoJEMhvYp4jgsXiFkkIALhWCtYC7qcthorB/s9STVkv
5VhPA7Jx9i9omnrsdzICXYC/HQaSN7gwgAPICYxTcAcen+qySHeXvk7jWh7PtQJ9
OHLWd1tYVxLV1y9tnmiFYVbJn017W0Kq0m4kkZEh6Q8KW0qE1xcHGREWHs/+1D4k
Rx798Tg6jgjt0nvg893aAcFQsgKxG53n5uqNySI9DKvxYcJBJkHD0/EgyHk+myVY
TPZj6f9xGwLCv0rQU6Vr29NniX1w2bRt6lYEp0KGlGjEGbiuStcRf6xUUmhxmDCs
faIspFMxpR4dqqeIq1Xh2x8S4QOMjDoiFGZmGBgrNdvLNOGNsd+QRhdLJiXuB88=
=8WVt
-----END PGP SIGNATURE-----
Merge tag 'highbank-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next/soc
From Rob Herring:
Highbank platform updates for 3.13
- convert Calxeda cpuidle driver to a platform driver and to use PSCI
- convert highbank smp_ops and suspend to PSCI
* tag 'highbank-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dts: calxeda: add ARM PSCI binding
ARM: highbank: adapt to use ARM PSCI calls
ARM: PSCI: remove unnecessary include of arm-gic.h
cpuidle: calxeda: add support to use PSCI calls
ARM: highbank: cpuidle: convert to platform driver
cpuidle: calxeda: add cpu_pm_enter/exit calls
- dove
- add audio devices
- fix bad properties of si5351 clkout2 for CuBox
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJSX+yTAAoJEAi3KVZQDZAev1wIAJA521UnQR6efGNEU6wD3Yvq
hjXEe+Da62FG2YUzZhOpLYIRrc0EvTrt/JIAbLbf5qrOnc9kzO6YdZVnRJJgWDP0
Qzak9C0xqfsFeR7MxnDuyJ10/TYgM1iugvUcs6tqRDb7LdqcGBv92vv8zCdieiiJ
XNtA56GVvEXo6LKp4KjC/dNv4vQBPEzDukSm81g/dfVDIhm7vbGMeNpFtHPHcNQa
lASc6NjYzZXBZlz/ckRIZeT+MePpPkWusb8DOtLkv6/pRJjtSLaQqSLR82l52U+E
eVb9SoQJWjxmrVLMEk3nUYvsWVgLtClND62snfpu+JP5ELb+DBwky4DzVvftpaY=
=P7l9
-----END PGP SIGNATURE-----
Merge tag 'dt-3.13-3' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu dt changes for v3.13 (round 3)
- dove
- add audio devices
- fix bad properties of si5351 clkout2 for CuBox
* tag 'dt-3.13-3' of git://git.infradead.org/linux-mvebu:
ARM: Dove: fix bad properties of the si5351 clkout2 used by Cubox audio
ARM: Dove: Add the audio device to the Cubox DT
ARM: Dove: Add the audio devices in DT
Some small cleanups for MSM. Removes extraneous irq definitions that
aren't used on DT targets, moves the single existing board file to
board-dt.c in antipication of additional targets, and renames the
existing DT files to have a common 'qcom' prefix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=xAJK
-----END PGP SIGNATURE-----
Merge tag 'msm-cleanup-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From David Brown:
General cleanups for MSM for 3.13
Some small cleanups for MSM. Removes extraneous irq definitions that
aren't used on DT targets, moves the single existing board file to
board-dt.c in antipication of additional targets, and renames the
existing DT files to have a common 'qcom' prefix.
* tag 'msm-cleanup-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Rename msm devicetrees to have standard 'qcom' prefix
ARM: msm: Create a common board-dt and config ARCH_MSM_DT
ARM: msm: Remove irqs-*.h files for DT based targets
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- Fix up the LED support
- Update the Integrator defconfig
- Remove ATAG boot path
- Move some stuff over to the device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=p2Z9
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/soc
From Linus Walleij:
Integrator patches for the v3.13 kernel cycle:
- Fix up the LED support
- Update the Integrator defconfig
- Remove ATAG boot path
- Move some stuff over to the device tree
* tag 'integrator-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: core module registers from compatible strings
ARM: integrator: use devm_ioremap() to remap CM
cpufreq: probe the Integrator cpufreq driver from DT
ARM: integrator: move CM base into device tree
ARM: integrator: decommission the <mach/irqs.h> header
ARM: integrator: delete non-devicetree boot path
ARM: integrator: print the Linux IRQ in LL_DEBUG code
ARM: integrator: get the LM interrupts from DT
ARM: integrator: update defconfig
ARM: integrator: get the CM control register by proxy
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Commit 05849c9381 (ARM: tegra30: convert
device tree files to use CLK defines) updated the Tegra30 device tree to
use symbolic clock names but forgot to update this node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The display controller found on Tegra30 SoCs is backwards-compatible
with the one on Tegra20 SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch splits the sama5d3 SoCs definition:
- a common base for all sama5d3 SoCs (sama5d3.dtsi)
- several optional peripheral definitions which will be included by sama5d3
specific SoCs (sama5d3_'periph name'.dtsi)
- sama5d3 specific SoC definitions (sama5d3x.dtsi)
This provides a better representation of the real hardware (drop unneed
dt nodes) and avoids peripheral id conflict (which is not the case for
current sama5d3 SoCs, but could be if other SoCs of this family are
released).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: add more "sama5d3?" compatibility strings]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch splits the sam9x5 peripheral definitions into:
- a common base for all sam9x5 SoCs (at91sam9x5.dtsi)
- several optional peripheral definitions which will be included by specific
sam9x5 SoCs (at91sam9x5_'periph name'.dtsi)
This provides a better representation of the real hardware (drop unneeded
dt nodes) and avoids future peripheral id conflict (lcdc and isi both use
peripheral id 25).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This augments the core machine code for the Integrator platforms
to get their references to the core module device nodes by
using compatible strings instead of predefined node names
and rename the CP syscon node to be simply "syscon".
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the core module (CM) control base into the device
tree. It is a simple memory range of 0x200 bytes. Move the
cm header down into the machine directory and unexport the
cm_control() symbol as no modules are using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OF/DT boot path needs to get the LM (Logical Module)
IRQs from the device tree for coherency. This augments the
DT syscon node to contain these IRQs and alter the DT LM
code to get them from there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Revision 0 of Exynos4210 SoC (used on Universal C210 board) requires
'secure' PL330 MDMA1 address (0x12840000) instead of 'non-secure' one
(0x12850000). Fix it by overriding the default PL330 MDMA1 address in
exynos4210-universal_c210.dts.
This is a Device Tree (DT) version of commit 91280e7 ("ARM: EXYNOS:
PL330 MDMA1 fix for revision 0 of Exynos4210 SOC") and fixes recent
regression caused by conversion to DT-only setup on ARM EXYNOS.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos cpufreq drivers does not support device tree based regulator
lookup, so it can get the VDD ARM regulator only by its name. To get
cpufreq working for now, this patch works this around by renaming the
regulator in board dts files to vdd_arm, which is the name expected by
the driver.
This fixes a regression introduced by dropping support of board file
based bootup of Exynos 4210 boards that rendered cpufreq inoperable on
Trats and Origen boards.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes '_' from "early_prink" on Exynos5440 dts
files in according to kernel-parameters document.
Signed-off-by: Youngmin Nam <youngmin.nam@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Jungseok Lee <jays.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Corrects an obvious typo in the Arndale pinctrl descriptions in DT.
The samsung-pinctrl driver uses the correct name.
Signed-off-by: Al Stone <al.stone@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Tegra124 GPIO controller is identical to Tegra30, so copy the
DT node from tegra30.dtsi to tegra124.dtsi.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
n900 secure mode changes. Note that the n900 secure mode changes
will still be needed for device tree based booting also.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WRd/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
From Tony Lindgren:
Platform data changes for omaps for the display subsystem and
n900 secure mode changes. Note that the n900 secure mode changes
will still be needed for device tree based booting also.
* tag 'omap-for-v3.13/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (508 commits)
ARM: OMAP2+: display: Create omap_vout device inside omap_display_init
ARM: OMAP2+: display: Create omapvrfb and omapfb devices inside omap_display_init
ARM: OMAP2+: display: Create omapdrm device inside omap_display_init
ARM: OMAP2+: drm: Don't build device for DMM
RX-51: Add support for OMAP3 ROM Random Number Generator
ARM: OMAP3: RX-51: ARM errata 430973 workaround
ARM: OMAP3: Add secure function omap_smc3() which calling instruction smc #1
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add the minimal DTS support for DRA7xx based SoC core.
Add the initial support for N900 and gta04 phones.
Enable USB3 on OMAP5 evm board.
Add support for cryto accelerators
Add new IGEP AQUILA board
Add AM33XX EDMA support
Update HSUSB node to use the reset-gpios fmwk
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=808Q
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
omap device tree related changes via Benoit Cousson <bcousson@baylibre.com>:
Add the minimal DTS support for DRA7xx based SoC core.
Add the initial support for N900 and gta04 phones.
Enable USB3 on OMAP5 evm board.
Add support for cryto accelerators
Add new IGEP AQUILA board
Add AM33XX EDMA support
Update HSUSB node to use the reset-gpios fmwk
* tag 'omap-for-v3.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (58 commits)
ARM: dts: dra7-evm: Add mmc2 node for eMMC support
ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
ARM: dts: omap5-uevm: mark TWL6037 as system-power-controller
ARM: dts: omap3-igep0020: use standard constant for IRQ flags
ARM: dts: omap3-igep0020: Add HS USB Host support
ARM: dts: omap3-igep: Add USB OTG support
ARM: dts: AM33XX beagle black: add pinmux and hdmi node to enable display
ARM: dts: AM33XX: Add LCDC info into am335x-evm
ARM: dts: AM437X: Add DES node
ARM: dts: AM437X: Add AES node
ARM: dts: AM33XX: Fix AES interrupt number
ARM: dts: AM33XX: Add AES data and documentation
ARM: dts: AM33XX: Add SHAM data and documentation
ARM: dts: OMAP4: Add DES3DES node
ARM: dts: OMAP4: Add AES node
ARM: dts: am335x-evm[sdk]: switch mmc1 to 4-bit mode
ARM: dts: am335x-bone-common: correct mux mode for cmd line
ARM: dts: AM33XX: Add support for IGEP AQUILA EXPANSION board.
ARM: dts: AM33XX: Add support for IGEP COM AQUILA
ARM: dts: am335x-boneblack: move fixed regulator to board level
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=bqsS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to prepare for making omap3 device tree only:
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
* tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (523 commits)
ARM: configs: omap2plus_defconfig: enable dwc3 and dependencies
ARM: OMAP2+: Add WLAN modules and of_serial to omap2plus_defconfig
ARM: OMAP2+: Run make savedefconfig on omap2plus_defconfig to shrink it
ARM: OMAP2+: Add minimal 8250 support for GPMC
ARM: OMAP2+: Use pdata quirks for wl12xx for omap3 evm and zoom3
ARM: OMAP: Move DT wake-up event handling over to use pinctrl-single-omap
ARM: OMAP2+: Add support for auxdata
pinctrl: single: Add support for auxdata
pinctrl: single: Add support for wake-up interrupts
pinctrl: single: Prepare for supporting SoC specific features
ARM: OMAP2+: igep0020: use display init from dss-common
ARM: OMAP2+: pdata-quirks: add legacy display init for IGEPv2 board
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
* Does not include any new bindings or bindings change
* Add dts file for a SOCFPGA with an Arria V FPGA
* Add a clocks property for the TWD timer
* Add support for Terasic SocKit Board which has Cyclone5 FPGA
* From Steffen Trumtrar:
"This series includes some minor cleanups (indentation and clock labels) and
reorders the socfpga dts hierarchy from:
socfpga.dtsi
-> socfpga_$board.dts
-> socfpga_$otherboard.dts
to
socfpga.dtsi
-> socfpga_cyclone5.dtsi
--> socfpga_cyclone5_$board.dts
--> socfpga_cyclone5_$otherboard.dts
"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jmLh
-----END PGP SIGNATURE-----
Merge tag 'socfpga-dts-updates-for-v3.13' of git://git.rocketboards.org/linux-socfpga-next into next/dt
From Dinh Nguyen:
Updates to dts file structure for Altera's SOCFPGA
* Does not include any new bindings or bindings change
* Add dts file for a SOCFPGA with an Arria V FPGA
* Add a clocks property for the TWD timer
* Add support for Terasic SocKit Board which has Cyclone5 FPGA
* From Steffen Trumtrar:
"This series includes some minor cleanups (indentation and clock labels) and
reorders the socfpga dts hierarchy from:
socfpga.dtsi
-> socfpga_$board.dts
-> socfpga_$otherboard.dts
to
socfpga.dtsi
-> socfpga_cyclone5.dtsi
--> socfpga_cyclone5_$board.dts
--> socfpga_cyclone5_$otherboard.dts
"
* tag 'socfpga-dts-updates-for-v3.13' of git://git.rocketboards.org/linux-socfpga-next:
dts: socfpga: Add support for Altera's SOCFPGA Arria V board
ARM: socfpga: dts: fix s2f_* clock name
ARM: socfpga: dts: cleanup indentation
ARM: socfpga: dts: Add support for terasic SoCkit
ARM: socfpga: dts: Move common nodes to cyclone5 dtsi
arm: socfpga: Add clock for smp_twd timer
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Basic devicetree files for the rk3188 SoC. Also provided is a board
dts file for the upcoming Radxa Rock board using this SoC.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK2928 and RK3066 contain a dw_apb timer component, while the rk3188 uses
a slightly similar but still different timer component. But all of them
support the ARM-global-timer that got added as clocksource driver recently.
So enable support for it to get a working clocksource for rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3188 SoC shares a lot of peripherals with the rk3066 SoC,
but not all. Therefore move the common parts to a shared dtsi.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
From Simon Horman:
* renesas/dt2: (21 commits)
ARM: shmobile: bockw: fixup ether node naming
ARM: shmobile: r8a7779: add irqpin default status on DTSI
ARM: shmobile: marzen: fixup SMSC IRQ number on DTS
ARM: shmobile: bockw: add SMSC support on DTS
ARM: shmobile: r8a7778: add renesas_intc_irqpin support on DTSI
ARM: shmobile: r8a7791 SMP device tree node
ARM: shmobile: r8a7791 Arch timer device tree node
ARM: shmobile: r8a7791 IRQC device tree node
ARM: shmobile: armadillo800eva-reference: add SDHI and MMCIF interfaces
ARM: shmobile: armadillo-reference: Add PWM backlight node to DT
ARM: shmobile: r8a73a4: add a DT node for the DMAC
ARM: shmobile: r8a7790: add I2C DT nodes
ARM: shmobile: only enable used I2C interfaces in DT on all Renesas boards
ARM: shmobile: r8a7778: add usb phy power control function
ARM: shmobile: r8a7778: add USBHS clock
ARM: shmobile: r8a7791 CMT support
ARM: shmobile: r8a7791 SCIF support
ARM: shmobile: Initial r8a7791 SoC support
ARM: shmobile: r8a7778: add SSI/SRU clock support
ARM: shmobile: r8a7790: Add DU and LVDS clocks
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
These were used only in one intermediate variant of the pinctrl
driver but forgotten in the dtsi file. rockchip,config properties are
neither part of the actual binding nor handled by the pinctrl driver
at all, so remove them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
I've tested the serial, MMC, smsc911x, wl12xx, and off-idle support
with the pinctrl patches, so it probably works better than the
board-*.c files ever did. Also the board-omap3evm.c file is broken
for the DSS, and has been for a while. Patches are welcome to fix
it in this .dts file, let's just drop the board-*.c file for this.
Note that off-idle currently requires doing request_irq() on the
wake-up pin from pinctrl-single IRQ domain until we can handle
that in some Linux generic way.
[tony@atomide.com: updated for make dtbs build fix]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the main difference between the TMDSEVM3530 and
TMDSEVM3730 is just the omap processor:
http://www.ti.com/tool/tmdsevm3530http://www.ti.com/tool/tmdsevm3730
So let's add a common file for the EVMs, and fix the description
for the omap3-evm.dst as that's clearly for the TMDSEVM3530
since it includes omap34xx.dtsi. It cannot support the TMDSEVM3730
properly, and we need a separate file for that in the following
patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need the fixes in v3.12-rc5, dts changes in omap-for-v3.13/dt, and
the platform data quirk changes in omap-for-v3.13/quirk to start
removing omap3 board files without breaking things.
Add sound support on at91sam9n12ek board with wm8904 as codec.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable wm8904 codec on at91sam9n12ek board, which is connect
to i2c0 bus with 0x1a as address.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This fixes a long-standing Integrator/CP regression from
commit 870e2928cf
"ARM: integrator-cp: convert use CLKSRC_OF for timer init"
When this code was introduced, the both aliases pointing the
system to use timer1 as primary (clocksource) and timer2
as secondary (clockevent) was ignored, and the system would
simply use the first two timers found as clocksource and
clockevent.
However this made the system timeline accelerate by a
factor x25, as it turns out that the way the clocking
actually works (totally undocumented and found after some
trial-and-error) is that timer0 runs @ 25MHz and timer1
and timer2 runs @ 1MHz. Presumably this divider setting
is a boot-on default and configurable albeit the way to
configure it is not documented.
So as a quick fix to the problem, let's mark timer0 as
disabled, so the code will chose timer1 and timer2 as it
used to.
This also deletes the two aliases for the primary and
secondary timer as they have been superceded by the
auto-selection
Cc: stable@vger.kernel.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Without the "clock-frequency" property in arch timer node, could able
to see the below crash dump.
[<c0014e28>] (unwind_backtrace+0x0/0xf4) from [<c0011808>] (show_stack+0x10/0x14)
[<c0011808>] (show_stack+0x10/0x14) from [<c036ac1c>] (dump_stack+0x7c/0xb0)
[<c036ac1c>] (dump_stack+0x7c/0xb0) from [<c01ab760>] (Ldiv0_64+0x8/0x18)
[<c01ab760>] (Ldiv0_64+0x8/0x18) from [<c0062f60>] (clockevents_config.part.2+0x1c/0x74)
[<c0062f60>] (clockevents_config.part.2+0x1c/0x74) from [<c0062fd8>] (clockevents_config_and_register+0x20/0x2c)
[<c0062fd8>] (clockevents_config_and_register+0x20/0x2c) from [<c02b8e8c>] (arch_timer_setup+0xa8/0x134)
[<c02b8e8c>] (arch_timer_setup+0xa8/0x134) from [<c04b47b4>] (arch_timer_init+0x1f4/0x24c)
[<c04b47b4>] (arch_timer_init+0x1f4/0x24c) from [<c04b40d8>] (clocksource_of_init+0x34/0x58)
[<c04b40d8>] (clocksource_of_init+0x34/0x58) from [<c049ed8c>] (time_init+0x20/0x2c)
[<c049ed8c>] (time_init+0x20/0x2c) from [<c049b95c>] (start_kernel+0x1e0/0x39c)
THis is because the Exynos u-boot, for example on the Chromebooks, doesn't set
up the CNTFRQ register as expected by arch_timer. Instead, we have to specify
the frequency in the device tree like this.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
[olof: Changed subject, added comment, elaborated on commit message]
Signed-off-by: Olof Johansson <olof@lixom.net>
noticed now that people are actually using the device tree
based booting for omap3.
Also one regression fix for timer compile for dra7xx when
omap5 is not selected, and a LED regression fix for n900.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSVFFqAAoJEBvUPslcq6VzmMwP+wYGQ1a0Dyq/nHvHFbsm8Ny2
QQJBcz2QqiOUk3gCENl5MJ2CWeKr9vsB9JoC+BAWbaJ2qc20ru/LcT8vrd1bvFFm
qfvQzdSQubV+6//aTTjWc0pCfNw5ElpfjVztR3NbA6r1x4N3UISsLhLM20UOlq7v
aS6tIcP66H2haJRX5SIQkow8/zT1/YRZ3w368JDRCUWD+Lj+ceDasgyJVpPkIscV
q15EFSi4RWboxY6d6u5LkQwdxnX4cBL5/TWD/jHP2OGtDwdpg3aXW9uLrewETXlT
4OGh7igHe7mBXnUpWgOB5vjElp3i7zN81//hIe7rNys4hj4ED7t71n/qy90EOJWm
fH2mou/lOmqIXhEB68vOT88BeGlrELBRu6hrA56aem7LWOZKkIRIPEhC2qE/r18l
YIcBMsNlxxWY0ebmJvmvYCDxUyJpMIxePZ3k1xwybNojbSI0CRGd1qZMQoDWV6Yd
dbnvs+f0sCy7lOjrg9u/miCZJnc+wrkoKDQUfFiP2gHWQpQyBswOFO76VD7zW4DX
zLZs4oGml+Tc3LyLlTFdoMKeeW2AmQHKBNEupUzWhL0AjndTTetD4S3YwU8EfAVS
hPkzT0gI5oum3TypIdCr9Wmobn0tzJGI/rLxe5UJCeVbWpDfwqyccEy1wF/ET4FO
bVvy4NsDCHOSeDbAi8Xe
=yVzH
-----END PGP SIGNATURE-----
Merge tag 'fixes-against-v3.12-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few fixes for omap3 related hangs and errors that people have
noticed now that people are actually using the device tree
based booting for omap3.
Also one regression fix for timer compile for dra7xx when
omap5 is not selected, and a LED regression fix for n900.
* tag 'fixes-against-v3.12-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
ARM: mach-omap2: board-generic: fix undefined symbol
ARM: dts: Fix pinctrl mask for omap3
ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for lvds backlight on boards
i.MX6q-SabreSD and i.MX6dl-SabreSD
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- Clock tree support
- Clock management support using PM core
- Keystone config update for EMDA with ack from Vinod
- Enable SPI and I2C drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSV0ACAAoJEHJsHOdBp5c/ExIP/1DYAcJoHnSx0MZwXIl0mmHu
klHWr1QDH+kqwlbxnylAJ8LgsPFDmhdW0TD1vuvSBYjH19Yrm4HwWNLJ1V26F0uq
kd3fVYTx8Zm5YNk6kI4SJDeWC3GPtB6QgSwenTv9LpRggM99vkw9iLLEouuVKK0C
AzDNg4CI+8pHRZIqWoGS5o0e14+x1zCcORL3J4mpsgbT88Lu0lbuKuPLhGquuWRP
FeCvL8CSc4iqP81eFm1vy5Gix6bOIPaXCkey8xeMCKUhx4po1kj5hdiPwDlm4w8R
M8iMotbaeZazo8tZGy2++XA4viAaIWbioDi/AhvfVuoSdtsHK6X/7+bnhK77R7wh
rpVyhlnHSewFHLMDd5IE+mVGpzBkp2neLFwY5xbS/Acqplwcdlpa9cbQk/lYXZ7k
0esShfBgMf42h+bWMXpgxV8To4Qisy0bQ723AKEZwgVVM8YkKNNwIHO70rEqWp5+
M7qtKJF6AfvH8IRWwTB9Ce99g6k3OAfidDEgC7BMLKv3zc6/bTR1N4xjobp109eq
sSgVfZERdnBriNvjZWxICpCqoMVN8hqkL4IeLR16s3cXuU8H4rxq5HqnH5/AEDa5
1agJYGnE0CzmurMCyMrsT9IQjd7C+zJftp7TrO2y48OzAQKW4wdbuK6xPH0chFR0
dtMA3wY/nB+FOb51bmnf
=d2uA
-----END PGP SIGNATURE-----
Merge tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc
From Santosh Shilimkar:
SOC updates for Keystone II devices:
- Clock tree support
- Clock management support using PM core
- Keystone config update for EMDA with ack from Vinod
- Enable SPI and I2C drivers
* tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: (510 commits)
ARM: keystone: Enable I2C and SPI bus support
ARM: keystone: Select TI_EDMA to be able to enable SPI driver
dma: Allow TI_EDMA selectable for ARCH_KEYSTONE
ARM: dts: keystone: Add the SPI nodes
ARM: dts: keystone: Add i2c device nodes
ARM: keystone: add PM domain support for clock management
ARM: keystone: Enable clock drivers
ARM: dts: keystone: Add clock phandle to UART nodes
ARM: dts: keystone: Add clock tree data to devicetree
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add mmc2 dt node to dra7-evm board
and model eMMC vcc as fixed regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21)
on i2c1 bus. When dt support for gpio-pcf857x is available, input supply
will be modelled as cascaded regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This allows the palmas pm_power_off to kick in on power off command
and switch off the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Commit 840ef8b7 ("ARM: dt: add header to define IRQ flags") added
constants for IRQ edge/level triggered types so use it instead of
a magic number to enhance the DT readability.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add device nodes for the HS USB Host port 1, USB PHY and its
required regulator and also pin mux setup for HS USB1 pins.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Commit ad871c10b ("ARM: dts: OMAP: Add usb_otg and glue data to O
added USB OTG support for most OMAP boards but some OMAP3 boards
such as IGEP boards were not updated. This patch adds an USB OTG
device node to these board.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Enable the hdmi output and the LCD Controller on BeagleBone
Black. Also configure the correct pinmux for output of
video data from the SoC to the HDMI encoder.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add LCDC device node in DT for am33xx
Add LCDC and Panel info in DT for am335x-evm
Changes:
- remove redundant/unnecessary SoC specific setting in the board dts
- resolved conflicts on for_3.13/dts
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AM437x SoC has a DES3DES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AM437x SoC has AES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AES interrupts were previously not used, but after recent changes
to omap-aes driver, its being used.
Correct the interrupt number to have working PIO mode.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add the generic AM33XX AES module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms. Also add Documentation file describing the data
for the AES module.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add the generic AM33XX SHAM module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms. Also add Documentation file describing the data
for the SHAM module.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
OMAP4 has an DES3DES module that uses the omap-des crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
OMAP4 has an AES module that uses the omap-aes crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Set pinmux_emmc_pins mux mode for cmd line to MODE2 in order
to detect eMMC on BBB and BBW + eMMC cape.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP AQUILA EXPANSION board is a development platform
for the IGEP COM AQUILA AM335x boards.
The board adds the following connectivity:
o USB OTG
o USB HOST
o HDMI
o Ethernet
o Serial Debug (3.3V)
o 2x46 pin headers
o EEPROM
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP COM AQUILA is industrial processors SODIMM module with
following highlights:
o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor
o Cortex-A8 ARM CPU
o 3.3 volts Inputs / Outputs use industrial
o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
o MicroSD card reader on-board
o Ethernet controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
3.3V fixed regulator does not belong to TPS node - as a result
the fixed regulator is never probed and MMC is continually deferred
due to lack of regulator.
Move the fixed regulator to be at root of platform.
Cc: Joel Fernandes <joelf@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add information about the USB OTG PHY. Without this
the OTG port on beagle will not work.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Provide RESET GPIO and Power regulator for the USB PHY,
the USB Host port mode and the PHY device for the controller.
Also provide pin multiplexer information for USB host pins.
We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Set the alias for ethernet0 and ethernet1 so that uBoot
can set the MAC address appropriately.
Currently u-boot cannot find the alias and there for does
not set the MAC address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add DT nodes for TPS659038 PMIC on DRA7 boards.
It is based on top of:
http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.
Documentation:
- Documentation/devicetree/bindings/mfd/palmas.txt
- Documentation/devicetree/bindings/regulator/palmas-pmic.txt
Boot Tested on DRA7 d1 Board.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix indentation and changelog]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
"gpmc,sync-clki-ps" is not defined/documented, it should be
"gpmc,sync-clk-ps" instead.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefine this on each board DT file.
Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
am33xx boards DTS include the am33xx.dtsi Device Tree
source file that already define a pinmux device node for
the AM33XX SoC Pin Multiplex.
Redefining this for each board makes the Device Tree files
harder to modify and maintain so let's just use what is
already defined in the included .dtsi file.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This matches the vendor 3.8.x configuration that is shipping
with the boards.
The LED layout is now:
USR0: heartbeat
USR1: mmc0 (micro-SD slot)
USR2: cpu0
USR3: mmc1 (eMMC)
The cpu0 triggers was put in between the mmc triggers to make
is easier to see where the disk activity is.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The micro-SD slot hooks up all four data pins so lets' use them.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The pinmux is specified in am335x-bone-common.dtsi to be
reused by the eMMC cape.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix traling spaces and useless comments]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This enables the use of MMC cards even when no card was inserted at boot.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Adds AM33XX MMC support for am335x-bone, am335x-evm and am335x-evmsk boards.
Also added is the DMA binding definitions based on the generic DMA request
binding.
Additional changes made to DTS:
* Interrupt, reg and compatible properties added
* ti,needs-special-hs-handling added
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Adds DMA resources to the AM33XX SPI nodes.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Adds AM33XX EDMA support to the am33xx.dtsi as documented in
Documentation/devicetree/bindings/dma/ti-edma.txt
[Joel Fernandes <joelf@ti.com>]
Drop DT entries that are non-hardware-description as discussed in [1]
[1] https://patchwork.kernel.org/patch/2226761/
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This patch makes the Tegra RTC enabled as default for Tegra124 platform.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Keystone2 based SOCs supports 3 instances of SPI controllers. Add
the device nodes for them.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Keystone2 based SOCs supports 3 instances of i2c controllers. Add
the device nodes for them. The i2c0 child device AT24C1024 EEPROM node
is also added. When different board variants are added in future, it
can be moved to the supported boards from common SOC file.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Now pinctrl-single-omap can handle the wake-up events for us now
as long as the events are configured in the .dts files.
Done in collaboration with Roger Quadros <rogerq@ti.com>.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* SMP support for r8a7791 SoC
* r8a7779_init_irq_extpin() for DT for r8a7779 and r8a7778 SoCs
* Add HPB-DMAC to r8a7779 and r8a7778 SoCs
* Add r7s72100 SoC
* Make use of ARCH timer workaround on r8a7791 SoC
* Add IRQC platform device support to r8a7791 SoC
* Add I2C clocks and aliases for the DT mode for r8a7790 SoC
* Add MAC platform device to r8a73a4 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=4wdR
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Second Round of Renesas ARM based SoC updates for v3.13
* SMP support for r8a7791 SoC
* r8a7779_init_irq_extpin() for DT for r8a7779 and r8a7778 SoCs
* Add HPB-DMAC to r8a7779 and r8a7778 SoCs
* Add r7s72100 SoC
* Make use of ARCH timer workaround on r8a7791 SoC
* Add IRQC platform device support to r8a7791 SoC
* Add I2C clocks and aliases for the DT mode for r8a7790 SoC
* Add MAC platform device to r8a73a4 SoC
* tag 'renesas-soc2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791 SMP support
ARM: shmobile: r8a7779: split r8a7779_init_irq_extpin() for DT
ARM: shmobile: r8a7778: split r8a7778_init_irq_extpin() for DT
ARM: shmobile: r7s72100 SCIF support
ARM: shmobile: Initial r7s72100 SoC support
ARM: shmobile: r8a7791 Arch timer workaround
ARM: shmobile: r8a7791 IRQC platform device support
ARM: shmobile: Introduce r8a7791_add_standard_devices()
ARM: shmobile: Break out R-Car Gen2 setup code
ARM: shmobile: r8a73a4: add a clock alias for the DMAC in DT mode
ARM: shmobile: r8a7790: add I2C clocks and aliases for the DT mode
ARM: shmobile: r8a7779: add HPB-DMAC support
ARM: shmobile: r8a7778: add HPB-DMAC support
ARM: shmobile: r8a73a4: add a DMAC platform device and clock for it
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add support for a new SOCFPGA board that has an Arria V FPGA along with
dual ARM Cortex-A9 cores.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: devicetree@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
The s2f_* clocks are called h2f_* in the datasheets.
Rename them accordingly in the socfpga.dtsi.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Some of the clock nodes and the rst-/sysmgr use wrong indentation.
Fix it.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
This adds basic support for the terasic SoCkit board.
The board includes an Altera Cyclone 5 SoC.
[Dinh Nguyen] - Changed to 115200 for baudrate in dts bootargs
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The current socfpga_cyclone5.dts describes the Altera Cyclone5 SoC Development
Kit. The Cyclone5 includes a SoCFPGA, which itself can be included in other
SoC+FPGA combinations.
Instead of having to describe all Cyclone5 common nodes in every board specific
dts, move socfpga_cyclone5.dts to a dtsi and include this in a new dts for the
Development Kit.
[Dinh Nguyen] - Changed to 115200 for baudrate in dts bootargs
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
- kirkwood
- use MBus DT binding for setting up the windows
- move crypto and nand underneath the mbus node
- ib62x0 has a u-boot env partition
- mvebu
- add the Armada XP matrix board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSVEKbAAoJEAi3KVZQDZAea2cH/0Vshr3Uift/HCY//dBHG91w
OKT539uF4UqTe3B3BmIxGYYpemQMU37R346LPTYiiaTEOCqR90J2sYJKHB+6Yld5
llyI00ulhv6vLVdbGjlLW376lemrilRmH+LRQJdz/UoG64xpJ2RkqATXAQFh1hKi
wLq5heB4T8kfWW3JF52XXR1UTbqJdZyc81gFY9ShSzc78nhyqYJ3MtXN37Cqwqqq
e3izWC9Ujms9maSshY6ENGbOp8vyRslUxcCEFSWChn61fgHVvOA/7zqMRAkts5Ag
cqccsTVR9v2p09O8WvpgM4N9ULwB+qSIS13tVBzOVRGJ3xx+wc8NfBqF/cr3S4I=
=b/Ew
-----END PGP SIGNATURE-----
Merge tag 'dt-3.13-2' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu dt changes for v3.13 (round 2)
- kirkwood
- use MBus DT binding for setting up the windows
- move crypto and nand underneath the mbus node
- ib62x0 has a u-boot env partition
- mvebu
- add the Armada XP matrix board
* tag 'dt-3.13-2' of git://git.infradead.org/linux-mvebu:
arm: mvebu: add support for the Armada XP Matrix board
ARM: kirkwood: ib62x0: add u-boot environment partition
ARM: kirkwood: Move the nand node under the mbus node
ARM: kirkwood: Move the crypto node under the mbus node
ARM: kirkwood: Remove kirkwood_setup_wins and rely on the DT binding
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- mvebu
- add MSI
- new compatible string for mv64xxx-i2c
- dove
- use the pre-processor
- define the MBus nodes
- add PCIe controllers
- add Globalscale D3Plug
- relocate internal registers nodes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSSaTkAAoJEAi3KVZQDZAeYvgH/iNIksOjc47pf3KDYZLtR2iP
8XYEC3LoxEA6fGJGzJ8AgdWt/V7dq9SRIXE/GxuDCKu/lNzuiBsnigkN9kguSKyA
KqJ7e3n28+3GrTficPyRre24rYwpPKTmlWhrZ4F+TyH42bN4C+TzoW53pNW5MFyv
1FGsUNj2QlzZGcv4CB9JfCWbcgJj2ApB99CB79cd8plrtxj4b1DZ22vxy2sXlSqd
AWMD8kuEaN5zcqpV98znYOEH2RzTnS3XGzG6wrgiulPcsjrLulCDVoMcCkk2jGb8
YaIulucrtvrUQyIcKeB0AvHytcRxsu2N4D6ZtZsJbithgr3tWEusq/fiW22ko68=
=yW5l
-----END PGP SIGNATURE-----
Merge tag 'dt-3.13' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu dt changes for v3.13
- mvebu
- add MSI
- new compatible string for mv64xxx-i2c
- dove
- use the pre-processor
- define the MBus nodes
- add PCIe controllers
- add Globalscale D3Plug
- relocate internal registers nodes
* tag 'dt-3.13' of git://git.infradead.org/linux-mvebu:
ARM: dove: add initial DT file for Globalscale D3Plug
ARM: dove: add PCIe controllers to SoC DT
ARM: dove: relocate internal registers device nodes
ARM: dove: add MBus DT node
ARM: dove: add MBUS_ID macro to Dove DT
ARM: dove: use preprocessor on device tree files
ARM: mvebu: link PCIe controllers to the MSI controller
ARM: mvebu: the MPIC now provides MSI controller features
ARM: dts: mvebu: Update with the new compatible string for mv64xxx-i2c
Signed-off-by: Kevin Hilman <khilman@linaro.org>
As defined in the DT, clkout2 is not allowed to change the pll inside
si5351.
This patch extends the properties of clkout2 so that it works as the
external clock of the audio device in the Cubox.
Also, as the second si5351 clock is not used in the Cubox, its
definition is removed.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch activates the audio device of the Cubox.
The audio flow (pin mpp_audio1) is output on both I2S and S/PDIF.
The third si5351 clock (#2, pin mpp13) is used as the external clock.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds the nodes to instantiate the audio devices of the Dove
boards.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Currently we get the following errors on imx51-babbage:
/display@di0: could not find display-timings node
/display@di0: no timings specified
/display@di1: could not find display-timings node
/display@di1: no timings specified
imx-drm imx-drm: failed to allocate buffer with size 0
Provide timing values for IPU1, which is connected to a DVI bridge and
to IPU2, which can be connected to the WVGA panel, so that both of them can
be functional.
While at it, disable the WVGA panel, so that DVI output becomes the default one.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for the Tegra124 based Venice2 reference board.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Initial support for Tegra 124 SoC. This is expected to be included in
the board DTS files.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Now since the clock tree is added, update UART dt nodes with clock data
and remove the hard coded clock frequency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
SoC family definitions at the moment are reactive to board needs
as a result, beagle-xm would matchup with ti,omap3 which invokes
omap3430_init_early instead of omap3630_init_early. Obviously, this is
the wrong behavior.
With clock node dts conversion, we get the following warnings before
system hangs as a result and 3630 based platforms fails to boot
(uart4 clocks are only present in OMAP3630 and not present in
OMAP3430):
...
omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
omap_hwmod: uart4: cannot _init_clocks
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2434
_init+0x6c/0x80()
omap_hwmod: uart4: couldn't init clocks
...
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: timer12: enabled state can only be entered from
initialized, idle, or disabled state
...
WARNING: CPU: 0 PID: 46 at arch/arm/mach-omap2/omap_hwmod.c:2224
_idle+0xd4/0xf8()
omap_hwmod: timer12: idle state can only be entered from enabled state
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: uart4: enabled state can only be entered from
initialized, idle, or disabled state
So, add specific compatiblity for 3630 to allow match for Beagle-XM
platform.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: left out ti,omap343x, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this node, there will be no palmas driver to notify
dwc3 that a cable has been connected and, without that, dwc3
will never initialize.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[kishon@ti.com: added dt properties for enabling vbus/id interrupts
and fixed vbus-supply value after SMPS10 is modeled as 2 regulators]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Use a common naming scheme "mode0name.modename flags" for the
USB host pins to be consistent.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds devicetree for gta04 (Openmoko next generation board) with necessary
support for mmc, usb, leds and button.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Populate uarts, timers, rtc, wdt, gpio, i2c, spi, cpsw & pwm nodes.
Reason for adding these nodes early - hwmod code required address
space of peripherals corresponding to these nodes (as address space
details are removed from hwmod database).
uart0, timers - 1 & 2 and synctimer were already present, so here the
remaining uarts & timers are added.
All properties as per the existing binding has been added for uart,
timer, rtc, wdt & gpio. Even though that was not the current scope
of work, felt adding those would reduce or require no effort later
to get these peripherals working.
For i2c, spi, cpsw & pwm - only the properties that were sure to be
correct has been added (main intention is to make hwmod happy and
avoid any later modification to here added properties).
While at it add "ti,hwmod" property to already existing nodes.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Update AM4372 cpu node to the latest cpus/cpu bindings for ARM.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The OMAP4 SoC family uses specially-designed PMIC (power management IC)
companion chip for power management needs: TWL6030/TWL6032.
Therefore there is a typical connection of PMIC to OMAP4 so we can
move it into separate .dtsi file and do not duplicate over
board-specific files.
Tested on OMAP4 SDP board and Pandaboard ES2.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
SMPS10 has two outputs OUT1 and OUT2. Hence SMPS10 is modeled as
two regulators. The DT node is split to reflect it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Following commit ff5c9059 and therefore other omap platforms using
the gpio-omap driver correct the #interrupt-cells property on am33xx
too. The omap gpio binding documentaion also states that
the #interrupt-cells property should be 2.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
ARM Performance Monitor Units are available on the am33xx,
add the support in the dtsi.
Tested with perf and oprofile on a regular beaglebone.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP COM MOdule has a GPIO LED connected to OMAP
pins. Configure this pin as output GPIO.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEPv2 has a number of GPIO LED connected to OMAP
pins. Configure these pins as output GPIO.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
IGEP boards have a number of LED connected to OMAP or TWL GPIO
lines. The actual wiring is different on each board so each board
DT has need to configure the mux correctly.
Even though it works with the current DT, the kernel complains with:
[2.305023] leds-gpio leds.18: pins are not configured from the driver
Add an empty pinmux_leds_pins pinctrl child node so boards can
override with the correct mux configuration and not depend on
default values for the GPIO LEDs to work.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds device tree with necessary support to boot with functional
video (on both emulator and real N900 device).
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Cubietech introduced a new cubieboard, the CubieTruck. This board added
more output connectors and features 2 GiB of RAM and a Gigabit PHY.
Tested are are uart0 and LEDS which both work as expected.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
dn and dp of USB1 can share with UART1(UART1 can route rx,tx to dn and dp pins of USB1).
here we add this pinmux capability.
USB1/UART1 mode selection has dedicated control register in RSC module, here we attach
the register offset of private data of related pin groups.
Signed-off-by: Rong Wang <Rong.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USP(Universal Serial Ports) can be UART as commit 5df831117b,
this patch defines the USP-based UART function pin groups for prima2.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the old codes defined uart0_nostreamctrl_pins, but missed pingroup
and padmux definition for it. this patch fixes it.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the ePAPR spec,
the node name should be "ethernet", not "lan0".
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when the legacy DTS file emev2-kzm9d.dts can be
used with board-kzm9d.c and board-kzm9d-reference.c
proceed with removing emev-kzm9d-reference.dts.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Copy the device nodes from KZM9D reference into the KZM9D
device tree file. This will allow us to use a single DTS
file regarless of kernel configuration. In case of legacy
C board code the device nodes may or may not be used, but
in the multiplatform case all the DT device nodes are used.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Genmai base board support making use of 128 MiB of memory,
the r7s7211 SoC with the SCIF2 serial port and CA9 core.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the r7272100 SoC including:
- Single Cortex-A9 CPU Core
- GIC
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WVMt
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes4-for-v3.12' into soc2-base
Fourth Round of Renesas ARM based SoC fixes for v3.12
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
Add initial support for the r7272100 SoC including:
- Single Cortex-A9 CPU Core
- GIC
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7779 INTC needs IRL pin mode settings to determine
behavior of IRQ0 - IRQ3. But it depends on platform.
This patch adds status = "disabled" on r8a7779.dtsi as default
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables INTC IRQ and SMSC on BockW board via DT.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the r8a7791 secondary CPU core.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7791 arch timer device tree information.
This needs to be used together with r8a7791 support
code that ties in the R-Car Gen2 arch timer workarounds.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable a r8a7791 IRQC block by adding a device tree
node for the IRQC hardware and pins IRQ0 to IRQ9.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI0 and MMCIF interfaces to armadillo800eva-reference with
regulators and pin configurations. SDHI1 is not added yet, because the
switch, that connects the interface either to an SD slot or to a WiFi
SDIO card cannot be described in DT yet.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the only system DMAC instance on r8a73a4. The RT DMAC
can be added later under the same multiplexer, because they can serve the
same slaves and use the same MID-RID values. Configuration data is
supplied to the driver, using a compatibility match string.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the four I2C interfacces on r8a7790.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently all I2C interfaces in all *.dtsi files for various Renesas SoCs
are enabled by default. Switch them all off and only enable populated I2C
interfaces in board-specific *.dts files.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Add support for r8a7791 SoC
* Rename DU device in clock lookups list of r8a7779 SoC
* USB and SSI/SRU clock support for r8a7778 SoC
* USB phy power control function support for r8a7778 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=GB2b
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v3.13' into dt2-base
Renesas ARM based SoC updates for v3.13
* Add support for r8a7791 SoC
* Rename DU device in clock lookups list of r8a7779 SoC
* USB and SSI/SRU clock support for r8a7778 SoC
* USB phy power control function support for r8a7778 SoC
Updated I2C nodes for HDMI-DDC and HDMI-PHY for Arndale board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add pinctrl node for hdmi hpd gpio pin to exynos5420 smdk board
file. hpd Gpio property is added to the hdmi node. This patch also
adds hdmi ddc node.
Both hdmi device and ddc i2c channel are enabled in
exynos5420-smdk5420.dts
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add hdmi and mixer device tree nodes for Exynos 5420 SoC.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This adds device-tree nodes for the i2c busses on Exynos
5420 platforms.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix wrong clock numbers in hdmi dt node. Removed hdmiphy
clock which was a dummy clock earlier and not required now.
Also added mux clock to change the clock parent.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the mixer clocks to the mixer node in the
exynos 5250 dts file.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add vcc-supply property in the nct1008 node, and set it
as sys_3v3_reg.
change the name of this node to temp-sensor.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
* Add CPU cores to DTSI of r8a7790 SoC
* Add MMCIF and SDHI DT nodes for reference DTS of ape6evm board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=OaGQ
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Renesas ARM-based SoC DT updates for v3.13
* Add CPU cores to DTSI of r8a7790 SoC
* Add MMCIF and SDHI DT nodes for reference DTS of ape6evm board
* tag 'renesas-dt-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Add r8a7790 CA7 CPU cores to DTSI
ARM: shmobile: Add r8a7790 CA15 CPU cores
ARM: shmobile: ape6evm-reference: add MMCIF and SDHI DT nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
* Display Unit support for lager and marzen boards
* Update regulators for MMC0, SDHI0 and SDHI1 on ape6evm board
* Enable use of FPGA on bockw board
* Add sounds support to bockw board
* Add USB function support to bockw board
* Add Koelsch board
* Disable MMCIF command completion signal on ape6evm, armadillo800eva,
kzm9g and lager boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSSToaAAoJENfPZGlqN0++XoUP/ikkPHbam+wNdKuR/IBCp+Wr
wvUChdfFw78UuYrYZgIC9C8jIwRO7L6j/5BmnxSOIppGa9t/HeyY2dXu3t8/D0Ye
T6GUzbciN/2/eX6e1rdLnK8ZAvw7HBqGig2VKEtsuI1enJBi7kWot2h/ITw60Y9L
nTNjwLpxTZ+WE7TK9B8KdYmxEU5X/EfI88Uu9ImXsEfUIUwxyH+c7BzQ/JNf1HVh
avTk9cJd/BCXJ2+S1axX0/PvQ6G81CgVn5fxVyMonzEl0boxLv72N8j81VTTHVSS
Yrvm63jivXsGR5woUvP1putNwz0VJkQ+m30m/7olZw673QD6D7dsBS8URJDliyHC
0yX3L0KVC0810IDo1gXx7Xr4CpF/jkwUNFGbmN2mayQOiWaxq+Jhrd8RQKTTNDDk
5J1uZQQE1+MuSc9vZuUUv+ElUhKYrzCXHFy9zztesnZ3HuRjI+3po/5+Ui7eNTlD
YUQuETcQhfuwFyRDjMnpomw5Hb78IWOSDwXAlxQ5V2LGaaroQMxX+0+3xHdgo1Nh
f+kMuqYJTNv1K6ymigoMtiKyXhI7+FW3ZDW76a9Mi3eKgJHQr0XqeGZ6DXGBUhq0
96ZD6631+KS9Zsl2hfuqo5iyrROQHBHl0IDfOSGZ4bRKb0SzqXnnFyLb9lOyY3uu
wTfQ65kFlJR/UAhs4xtf
=KUsf
-----END PGP SIGNATURE-----
Merge tag 'renesas-boards-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards
From Simon Horman:
Renesas ARM based SoC board updates for v3.13
* Display Unit support for lager and marzen boards
* Update regulators for MMC0, SDHI0 and SDHI1 on ape6evm board
* Enable use of FPGA on bockw board
* Add sounds support to bockw board
* Add USB function support to bockw board
* Add Koelsch board
* Disable MMCIF command completion signal on ape6evm, armadillo800eva,
kzm9g and lager boards.
* tag 'renesas-boards-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: disable MMCIF Command Completion Signal, add CLK_CTRL2
ARM: shmobile: kzm9g: disable MMCIF Command Completion Signal
ARM: shmobile: armadillo800eva: disable MMCIF Command Completion Signal
ARM: shmobile: ape6evm: disable MMCIF Command Completion Signal
ARM: shmobile: bockw: add USB Function support
ARM: shmobile: Koelsch support
ARM: shmobile: bockw: add R-Car sound support (PIO)
ARM: shmobile: bockw: enable global use of FPGA
ARM: shmobile: lager: Fix Display Unit platform data
ARM: shmobile: ape6evm: update MMC0, SDHI0 and SDHI1 with correct regulators
ARM: shmobile: lager: Add Display Unit support
ARM: shmobile: marzen: Add Display Unit support
ARM: shmobile: r8a7778: add usb phy power control function
ARM: shmobile: r8a7778: add USBHS clock
ARM: shmobile: r8a7791 CMT support
ARM: shmobile: r8a7791 SCIF support
ARM: shmobile: Initial r8a7791 SoC support
ARM: shmobile: r8a7778: add SSI/SRU clock support
ARM: shmobile: r8a7790: Add DU and LVDS clocks
ARM: shmobile: r8a7779: Rename DU device in clock lookups list
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add support for r8a7791 SoC
* Rename DU device in clock lookups list of r8a7779 SoC
* USB and SSI/SRU clock support for r8a7778 SoC
* USB phy power control function support for r8a7778 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=GB2b
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Renesas ARM based SoC updates for v3.13
* Add support for r8a7791 SoC
* Rename DU device in clock lookups list of r8a7779 SoC
* USB and SSI/SRU clock support for r8a7778 SoC
* USB phy power control function support for r8a7778 SoC
* tag 'renesas-soc-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7778: add usb phy power control function
ARM: shmobile: r8a7778: add USBHS clock
ARM: shmobile: r8a7791 CMT support
ARM: shmobile: r8a7791 SCIF support
ARM: shmobile: Initial r8a7791 SoC support
ARM: shmobile: r8a7778: add SSI/SRU clock support
ARM: shmobile: r8a7790: Add DU and LVDS clocks
ARM: shmobile: r8a7779: Rename DU device in clock lookups list
Signed-off-by: Olof Johansson <olof@lixom.net>
* Correct incorrect placement of __initdata tag in ape6evm board code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSTnhAAAoJENfPZGlqN0++oEEP/iO0a7Ofs/womZij1p05MIYH
Xb+LrQD5GHRtST9K4S+gwOzklignX7ri6I8P2+298YhKs7DuAjcmdn6J/3yEL/zB
irzRjBOnZ4AxtCbO424uUG0YNL2ahsG8/IbBL05XWXJLJLUacgu5Jexq7Yr+pndB
4ftqZxoFmrmEteirCp0N2jQGi5M4SQRUUGVvmpp3zaE3omavAmKUwqdZ0EQm/zim
iUhZ90lPrb53nfV5ryoNE6mEXWnUwZCXIY7TzKJm/FhNEp2Op+h/ai99pjnSdsjE
3DcNcR3IVmwVHD6rbkUrOXQfL9/ZhQgLTHGGqEJViCUgDEtqeIU1GFq7p69PLvFa
pimNM6zcRU9/cKoZLtiLP+huPgkNttdmESmPyXn4zjJrnM0fF0Guu363/v3HI6nk
6nP+KyVhqM/CJKLXIBLG3KWXwOhdVp3hkpVNHAJeCf6Hz3dEIXW6puUy7F2qreuX
akTw+ZFHeyI9pV32GSYtIFABE9hB+UrNTSM5K4eRuQkWBF+2XnlphFXsPJdJm6Du
XfkcowR/efdwVe/9xWOy8zGuxceIfzyLXWZtahFaEnmLPrvMJCaRqFlDjfs5D8eV
9Roz2iqAyZ/6vBNNqvZzSDwdgGuXu7/7kU1bB0zqSiS9DRekWXSCp5qqqsw4X2Aa
hujoEunX2uV9zEOCIUXt
=nVyt
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes5-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
* Correct incorrect placement of __initdata tag in ape6evm board code
* tag 'renesas-fixes5-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: ape6evm: fix incorrect placement of __initdata tag
(+ other patches already present in v3.12-rc4)
Signed-off-by: Olof Johansson <olof@lixom.net>
deletion: this fixes bugs discovered when switching to a
devicetree-only setup, primarily on the HREF prototypes.
The biggest change is to split into four DTS variants as
the UIB autodetection was lost.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xjIK
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Second part of the Ux500 devicetree conversion and ATAG
deletion: this fixes bugs discovered when switching to a
devicetree-only setup, primarily on the HREF prototypes.
The biggest change is to split into four DTS variants as
the UIB autodetection was lost.
* tag 'ux500-devicetree-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: move BU21013 touchpad GPIOs into top-level DTS
ARM: ux500: register the tc35892 GPIO on the TVK UIB
ARM: ux500: split the HREF DTS files from two to four
ARM: ux500: split HREF UIB files
ARM: ux500: move TC35892 at 0x42 to hrefprev60
ARM: ux500: correct CD for micro SD on hrev60plus
ARM: ux500: fix proximity sensor button
ARM: ux500: correct I2C address of ambient light sensor
ARM: ux500 enable the AB8500 gpio for all HREFs
ARM: ux500: add default trigger on HREF LED
Signed-off-by: Olof Johansson <olof@lixom.net>
Rather than requiring each board to explicitly disable the I2S controllers
it is not using instead require boards to enable those that they are using.
This is required for audio operation on Arndale, one of the unused I2S
controllers is pinmuxed with the LDO enable GPIOs for the WM1811A.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On the mx53qsb board with mc34708 PMIC, GPIO1_8 resets the system, so better not
to use it as a wakeup source.
Use GPIO 2_14 and 2_15 for wakeup sources instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
SDHC1 does not have any GPIO for reading the card detection status, so
remove 'cd-gpios'.
After this change card detection works via the internal SD controller mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
SDHC3 is 8 bit-wide, so pass the bus-width property to reflect that.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
