Support for non-DT kernels was mainly to use v3.4 downstream kernels.
This is no longer a priority now as we have reasonable support upstream.
Remove CONFIG_OF from the top level msm_drv.c file. While we're at it,
clean up the data matching process using of_device_get_match_data.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DRM_MSM_FBDEV config is used to enable/disable fbdev emulation for the
msm kms driver.
Replace this with the top level DRM_FBDEV_EMULATION config option where
applicable. This also prevents build breaks caused by undefined
drm_fb_helper_* functions when legacy fbdev support was disabled.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Just one special case (since i915 lost its ums code, yay):
- radeon: Has slots for the old ums ioctls which don't have
DRM_UNLOCKED, but all filled with drm_invalid_op. So ok to drop it
everywhere.
Every other kms driver just has DRM_UNLOCKED for all their ioctls, as
they should.
v2: admgpu happened, include that one too. And i915 lost its UMS
support which means we can change all the i915 ioctls too.
v3: Rebased on top of new vmwgfx DX interface extensions.
v4: Rebase on top of render-node support in exynos.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_vblank_count() returns the software counter. We should not pretend
it's the hw counter since we use the hw counter to figuere out what the
software counter value should be. So instead provide a new function
drm_vblank_no_hw_counter() for drivers that don't have a real hw
counter. The new function simply returns 0, which is about the only
thing it can do.
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
[danvet: s/int pipe/unsigned int pipe/ to follow Thierry's interface
change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This continues the pattern started in commit cc1ef118fc ("drm/irq:
Make pipe unsigned and name consistent"). This is applied to the public
APIs and driver callbacks, so pretty much all drivers need to be updated
to match the new prototypes.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Jianwei Wang <jianwei.wang.chn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
AHB clock should be enabled before accessing registers during
enable/disable_vblank(). Since these 2 callbacks are called in
atomic context while clk_prepare may cause thread sleep, a work
is scheduled to control vblanks.
v2: fixup spinlock initialization
Signed-off-by: Hai Li <hali@codeaurora.org>
[add comment about cancel_work_sync() before drm_irq_uninstall()]
Signed-off-by: Rob Clark <robdclark@gmail.com>
The maximum output width of one pipeline depends on the LayerMixer's
capability. It may be different on each target. Also, MDP5 doesn't
have vertical limitation in one frame, as long as the pixel clock
can be supported.
This change obtains the maximum LM resolution from configuration
table and treat it as the whole pipe's limitation for MDP5. The size
limit on MDP4 is not changed.
Signed-off-by: Hai Li <hali@codeaurora.org>
The atomic commit cannot easily undo and return an error once the
state is swapped. Change to uninterruptible wait, and ignore the
timeout error.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The 'timeout' value comes from userspace (CLOCK_MONOTONIC), but
converting this directly to jiffies doesn't take into account the
initial jiffies count at boot, which may differ from the base time
of CLOCK_MONOTONIC.
TODO: add ktime_delta_jiffies() when rebasing on 4.1 and use that
instead of ktime_sub/ktime_to_timespec/timespec_to_jiffies combo (as
suggested by Arnd)
v2: switch over from 'struct timespec' to ktime_t throughout, since
'struct timespec' will be deprecated (as suggested by Arnd)
v3: minor cosmetic tweaks
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In error paths, this was being called without struct_mutex held.
Leading to panics like:
msm 1a00000.qcom,mdss_mdp: No memory protection without IOMMU
Kernel panic - not syncing: BUG!
CPU: 0 PID: 1409 Comm: cat Not tainted 4.0.0-dirty #4
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
Call trace:
[<ffffffc000089c78>] dump_backtrace+0x0/0x118
[<ffffffc000089da0>] show_stack+0x10/0x20
[<ffffffc0006686d4>] dump_stack+0x84/0xc4
[<ffffffc0006678b4>] panic+0xd0/0x210
[<ffffffc0003e1ce4>] drm_gem_object_free+0x5c/0x60
[<ffffffc000402870>] adreno_gpu_cleanup+0x60/0x80
[<ffffffc0004035a0>] a3xx_destroy+0x20/0x70
[<ffffffc0004036f4>] a3xx_gpu_init+0x84/0x108
[<ffffffc0004018b8>] adreno_load_gpu+0x58/0x190
[<ffffffc000419dac>] msm_open+0x74/0x88
[<ffffffc0003e0a48>] drm_open+0x168/0x400
[<ffffffc0003e7210>] drm_stub_open+0xa8/0x118
[<ffffffc0001a0e84>] chrdev_open+0x94/0x198
[<ffffffc000199f88>] do_dentry_open+0x208/0x310
[<ffffffc00019a4c4>] vfs_open+0x44/0x50
[<ffffffc0001aa26c>] do_last.isra.14+0x2c4/0xc10
[<ffffffc0001aac38>] path_openat+0x80/0x5e8
[<ffffffc0001ac354>] do_filp_open+0x2c/0x98
[<ffffffc00019b60c>] do_sys_open+0x13c/0x228
[<ffffffc00019b72c>] SyS_openat+0xc/0x18
CPU1: stopping
But there isn't any particularly good reason to hold struct_mutex for
teardown, so just standardize on calling it without the mutex held and
use the _unlocked() versions for GEM obj unref'ing
Signed-off-by: Rob Clark <robdclark@gmail.com>
First of all, we don't want -EPROBE_DEFER when trying to bind children
to cause us to forget to free our vram. And second we don't want vram
allocation fail to trigger _unbind_all() before _bind_all().
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DRM_KMS_FB_HELPER config is selected only when DRM_MSM_FBDEV config is
selected. The driver accesses drm_fb_helper_* functions even when legacy fbdev
support is disabled in msm. Wrap around these functions with #ifdef checks to
prevent build break.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Avoid casts from pointers to fixed-size integers to prevent the compiler
from warning. Print virtual memory addresses using %p instead. Also turn
a couple of %d/%x specifiers into %zu/%zd/%zx to avoid further warnings
due to mismatched format strings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
This change adds the support in mdp5 kms driver for single
and dual DSI. Dual DSI case depends on the framework API
and sequence change to support dual data path.
v1: Initial change
v2: Address Rob Clark's comment
- Separate command mode encoder to a new file mdp5_cmd_encoder.c
- Rebase to not depend on msm_drm_sub_dev change
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support to use the VRAM carveout (if specified in dtb) for fbdev
scanout buffer. This allows drm/msm to take over a bootloader splash-
screen, and avoids corruption on screen that results if the kernel uses
memory that is still being scanned out for itself.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We'll want to extend this a bit to handle also a reserved-memory
("stolen") region, so that drm/msm can take-over bootloader splash
screen. First split it out into it's own fxn to reduce noise in
the following patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Useful to avoid recompiling to disable fbdev. Useful because otherwise
the first modeset happens under console_lock (ie. debugging sadness).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Modified the hard-coded hdmi connector/encoder implementations in msm drm
driver to support both edp and hdmi.
V1: Initial change
V2: Address Thierry's change
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Next batch of atomic work. Most important is the propertification from Rob
and the nth iteration of the actual atomic ioctl originally from Ville.
Big differences compared to earlier revisions:
- Core properties are now fully handled by the core, drivers can only
handle driver-specific properties.
- Atomic props&ioctl are opt-in per file_priv, userspace needs to
explicitly ask for it (like universal plane support).
- For now all hidden behind the atomic module option until this has
settled a bit.
- Atomic modesets are currently not possible since the exact abi for how
to handle the mode property is still under discussion.
Besides this some cleanup patches from me and the addition of per-object
state to global state backpointers to simplify drivers.
* tag 'topic/atomic-core-2015-01-05' of git://anongit.freedesktop.org/drm-intel:
drm: Ensure universal_planes is set for atomic
drm/atomic: Hide drm.ko internal interfaces
drm: Atomic modeset ioctl
drm/atomic: atomic connector properties
drm/atomic: atomic plane properties
drm: small property creation cleanup
drm/atomic: atomic_check functions
drm: add atomic properties
drm: refactor getproperties/getconnector
drm: tweak getconnector locking
drm: add atomic_get_property
drm: add atomic_set_property wrappers
drm: get rid of direct property value access
drm: store property instead of id in obj attachment
drm: allow property validation for refcnted props
drm/atomic: Introduce state->obj backpointers
drm/atomic-helper: Again check modeset *before* plane states
drm/atomic-helper: Export both plane and modeset check helpers
A few msm fixes for 3.19:
* hdmi regulators fix
* hdmi fix for spurious HPD interrupts
* fix for sync atomic update after async update (which could show
up with a setcrtc following a pageflip)
* couple little Coccinelle cleanups
* 'msm-fixes-3.19' of git://people.freedesktop.org/~robclark/linux:
drm/msm/hdmi: rework HDMI IRQ handler
drm/msm/hdmi: enable regulators before clocks to avoid warnings
drm/msm/mdp5: update irqs on crtc<->encoder link change
drm/msm: block incoming update on pending updates
drm/msm: Deletion of unnecessary checks before the function call "release_firmware"
drm/msm: Deletion of unnecessary checks before two function calls
We can't have multiple updates pending on a given CRTC, and we don't
want a sync update to race w/ an async update that preceeded it. So
keep track of which CRTCs have updates in flight, and block later
updates that would conflict.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This essentially reverts
commit 934ce1c236
Author: Rob Clark <robdclark@gmail.com>
Date: Wed Nov 19 16:41:33 2014 -0500
drm/atomic: check mode_changed *after* atomic_check
Depending upon the driver both orders (or maybe even interleaving) is
required:
- If ->atomic_check updates ->mode_changed then helper_check_modeset
must be run afters.
- If ->atomic_check depends upon accurate adjusted dotclock values for
e.g. watermarks, then helper_check_modeset must be run first.
The failure mode in the first case is usually a totally angry hw
because the pixel format switching doesn't happen. The failure mode in
the later case is usually nothing, since in most cases the old
adjusted mode from the previous modeset wont be too far off to be a
problem. So just underruns and perhaps even just suboptimal (from a
power consumption) watermarks.
Furthermore in the transitional helpers we only call ->atomic_check
after the new modeset state has been fully set up (and hence
computed).
Given that asymmetry in expected failure modes I think it's safer to
go back to the older order. So do that and give msm a special check
function to compensate.
Also update kerneldoc to explain this a bit.
v2: Actually add the missing hunk Rob spotted.
v3: Move msm_atomic_check into msm_atomic.c, requested by Rob.
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
Give ourselves a way to wait for certain fence #.. makes it easier to
wait on a set of bo's, which we'll need for atomic.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently msm does not implement gem_prime_mmap. Without this it is not
possible to draw onto a dma-buf from userspace (making its very hard to
implement the Android rendering model).
Fixing this is just a matter of adding a little boilerplate.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
drm: backmerge tag 'v3.17-rc5' into drm-next
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
If VRAM carveout is used, due to no IOMMU, we should have a default
value for msm.vram so that we don't simply crash.
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In particular, blend_setup() should not overwrite the other crtc's mixer
settings. Also, the encoder needs to be able to specify the mixer-id
explicitly, since both LVDS and DTV use 'INTF_LVDC_DTV', so we cannot
guess the mixer-id from the interface.
Signed-off-by: Rob Clark <robdclark@gmail.com>
One step closer to dropping all the drm_bus_* code:
Add a driver->set_busid() callback and make all drivers use the generic
helpers. Nouveau is the only driver that uses two different bus-types with
the same drm_driver. This is totally broken if both buses are available on
the same machine (unlikely, but lets be safe). Therefore, we create two
different drivers for each platform during module_init() and set the
set_busid() callback respectively.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Somewhere along the way, the firmware loader sprouted another lock
dependency, resulting in possible deadlock scenario:
&dev->struct_mutex --> &sb->s_type->i_mutex_key#2 --> &mm->mmap_sem
which is problematic vs things like gem mmap.
So introduce a separate mutex to synchronize gpu init.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that we (almost) have enough dependencies in place (MMCC, RPM, etc),
add necessary DT support so that we can use drm/msm on upstream kernel.
v2: update for review comments
v3: rebase on component helper changes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Update MSM's DRM driver to use the component match support rather than
add_components.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
All drm_fb_helper_restore_fbdev_mode() call sites, save one, do the same
locking. Simplify this into drm_fb_helper_restore_fbdev_mode_unlocked().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To ease debugging, add debugfs file which can be cat/tail'd to log
submits, along with fence #. If GPU hangs, you can look at 'gpu'
debugfs file to find last completed fence and current register state,
and compare with logged rd file to narrow down the DRAW_INDX which
triggered the GPU hang.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Unfortunately this requires a drm-wide change, and I didn't see a sane
way around that. Luckily it's fairly simple, we just need to inline
the respective get_irq implementation from either drm_pci.c or
drm_platform.c.
With that we can now also remove drm_dev_to_irq from drm_irq.c.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After reading a nice article on LWN[1], I went back and double checked
my handling of invalid-input checking. Turns out there were a couple
places I had missed.
Since the driver is fairly young, and the devices it supports are really
only just barely usable for basic stuff (serial console) with an
upstream kernel, I think we should fix this now and revert specific
parts of this patch later in the unlikely event that a regression is
reported.
[1] https://lwn.net/Articles/588444/
Signed-off-by: Rob Clark <robdclark@gmail.com>
Shut down the clks when the gpu has nothing to do. A short inactivity
timer is used to provide a low pass filter for power transitions.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This was hidden in a generic void * dev->mm_private. But only ever
used for gem. But thanks to this fake generic pretension no one
noticed that Rob's drm drivers are now all broken.
So just give the offset manager a type pointer and fix up msm, omapdrm
and tilcdc.
v2: Fixup compile fail.
v3: Fixup rebase fail that David spotted.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add support for the new MDP5 display controller block. The mapping
between parts of the display controller and KMS is:
plane -> PIPE{RGBn,VIGn} \
crtc -> LM (layer mixer) |-> MDP "device"
encoder -> INTF /
connector -> HDMI/DSI/eDP/etc --> other device(s)
Unlike MDP4, it appears we can get by with a single encoder, rather
than needing a different implementation for DTV, DSI, etc. (Ie. the
register interface is same, just different bases.)
Also unlike MDP4, all the IRQs for other blocks (HDMI, DSI, etc) are
routed through MDP.
And finally, MDP5 has this "Shared Memory Pool" (called "SMP"), from
which blocks need to be allocated to the active pipes based on fetch
stride.
Signed-off-by: Rob Clark <robdclark@gmail.com>
