Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Set MES watermark size to 0x50 for 43012. It fixes SDIO bus hang issue
when running at high throughput.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-6-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4354/4356 SDIO.
Also enable and configure F1 MesBusyCtrl. It would resolve random driver
crash issue.
Signed-off-by: Frank Kao <frank.kao@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-4-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes for 4373. It fixes DMA error while having
UDP bi-directional traffic. Also use a defined F1 MesBusyCtrl value.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-2-chi-hsien.lin@cypress.com
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43legacy did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43legacy will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-3-Larry.Finger@lwfinger.net
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43 did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43 will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Reported-and-tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-2-Larry.Finger@lwfinger.net
All macro names for SDIO device IDs are prefixed by vendor name to which
device ID belongs. So for consistency add Broadcom string vendor prefix to
all Cypress macro names as they belong to SDIO Broadcom vendor ID.
Change also Cypress 43012 value from decimal do hexadecimal notation to be
consistent with all other values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-11-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An incorrect value of use_fwsup is set for 4-way handshake offload for
WPA//WPA2-PSK, caused by commit 3b1e0a7bdf ("brcmfmac: add support for
SAE authentication offload"). It results in missing bit
BRCMF_VIF_STATUS_EAP_SUCCESS set in brcmf_is_linkup() and causes the
failure. This patch correct the value for the case.
Also setting bit BRCMF_VIF_STATUS_EAP_SUCCESS for SAE offload case in
brcmf_is_linkup() to fix SAE offload failure.
Fixes: 3b1e0a7bdf ("brcmfmac: add support for SAE authentication offload")
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1589277788-119966-1-git-send-email-chi-hsien.lin@cypress.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1785:5-8:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508074351.19193-1-yanaijie@huawei.com
Fix sparse warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2206:5:
warning: symbol 'brcmf_p2p_get_conn_idx' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508013249.95196-1-chenzhou10@huawei.com
When plumbing rxiv for (GTK) keys, current code does not use seq/seq_len
when present nor set iv_initialized for iovar wsec_key. This could
result in missing broadcast traffic after GTK rekey. The fix is setting
iv_initialized and using seq/seq_len for iovar wsec_key.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-4-git-send-email-wright.feng@cypress.com
The driver sends an action frame down and waits for dwell time to be
completed or aborted before sending out the next action frame.
Driver issues "scan abort" to cancel the current time slot, but this
doesn't have any effect because, we are not using scan engine for
sending action frame.
Fix is to use "actframe_abort" to cancels the current action frame.
Signed-off-by: Ryohei Kondo <ryohei.kondo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-3-git-send-email-wright.feng@cypress.com
Host driver parses and sets security params into FW passed by
supplicant. This has to be done after reiniting interface in the
firmware.
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-2-git-send-email-wright.feng@cypress.com
802.1d defines 0,3 for BE and 1,2 for BK. In pcie dongles, 0 & 3 are
mapped to 0 and 1,2 are mapped to 1. This change corrects this mapping,
so that BE & BK are given access precedence accordingly by pcie dongles.
Signed-off-by: Pramod Prakash <pramod.prakash@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-3-git-send-email-chi-hsien.lin@cypress.com
In WLAN, priority among various access categories of traffic is
always set by the AP using WMM parameters and this may not always
follow the standard 802.1d priority.
In this change, priority is adjusted based on the AP WMM params
received as part of the Assoc Response and the same is later used
to map the priority of all incoming traffic.
In a specific scenario where EDCA parameters are configured to be same
for all ACs, use the default FW priority definition to avoid queuing
packets of all ACs to the same priority queue.
This change fixes the following 802.11 certification tests:
* 11n - 5.2.31 ACM Bit Conformance test
* 11n - 5.2.32 AC Parameter Modification test
* 11ac - 5.2.33 TXOP Limit test
Signed-off-by: Saravanan Shanmugham <saravanan.shanmugham@cypress.com>
Signed-off-by: Justin Li <justin.li@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-2-git-send-email-chi-hsien.lin@cypress.com
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJetAhAAAoJEG4XJFUm622bADEH/A1OjAD3H1iZyTmXHP4T7yZe
TKJ+9I6B3BDR1czUTm+kUhrgBDNpdLLtu+b+5QXfpPLrtZ0FF/zjuazgueyqQpZ1
zudj+rG72njHpU0RKtO7wIBrCtckLPV0be+3026hztatJmJ7XQ9FvsanFPPsrrNv
0lh8E8kDUSynOW2me8FW1GBgDkGaBaicAs4FSjwNJC31Wo/VN5m9gEFkGpT1VJWP
l0xeEQ/N2mknQVuTR4CuMT9VJ0SNlJrLZpBVAqkmc170c3pKChl3LTNCnP925ye9
Nfqw2sQKgUPJKRbZR5wZTphGuu4krFv0ldWCvb0oFtZlCLIkiOz6+AA7b33oV2A=
=7ewK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is dead for more than 10 years. Remove it.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/b43/pio.c:768:10-25: WARNING: Comparison
of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113311.41026-1-yanaijie@huawei.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/b43/phy_n.c:5510:19-32: WARNING:
Comparison of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113300.40895-1-yanaijie@huawei.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:1060:6-12:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113357.41422-1-yanaijie@huawei.com
It was observed that P2P Cert. 5.1.19: DEVUT responds to Service
Discovery request failed due to DUT did not send GAS Comeback Response
after receiving request from test bed P2P peer. To fix this issue,
we need to add P2P Action Frame retry delay to enhance P2P connection
under VSDB and noisy environment, since the peer can be in other
channels under VSDB.
Signed-off-by: Justin Li <Justin.Li@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-4-git-send-email-wright.feng@cypress.com
P2P group formation fails since either peer is not able to send go-neg
confirm or dut is not able to send go-neg response. To fix this, retry
limit should be increased and dwell time check should be added.
Signed-off-by: Joseph Chuang <joseph.chuang@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-3-git-send-email-wright.feng@cypress.com
With RSDB feature, firmware is able to support two P2P-AGO or two
P2P-GC at the same time. So we add the second p2p connection type
to map to the second P2P connection bsscfg.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-2-git-send-email-wright.feng@cypress.com
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
In doing this, make brcmf_debugfs_add_entry() return void as no one was
even paying attention to the return value.
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafał Miłecki" <rafal@milecki.pl>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200429101526.GA2094124@kroah.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:2359:6-40:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426094053.23132-1-yanaijie@huawei.com
Miracast Certification clause 6.1.2 may fail if there is no WFD IE in
p2p assoc response. This change allows WFD IE to be added to p2p assoc
response.
Related WFA certification:
6.1.2 P-SnUT operating as a Group Owner accepts a WFD Session with a
Reference Source
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Ryohei Kondo <ryohei.kondo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-6-git-send-email-chi-hsien.lin@cypress.com
P2p spec mentioned that the p2p device address should be the globally
administered address with locally administered bit set. Therefore,
follow this guideline by default.
When the primary interface is set to a locally administered address, the
locally administered bit cannot be set again. Generate a random locally
administered address for this case.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-5-git-send-email-chi-hsien.lin@cypress.com
Send p2p presence response from the p2p interface address instead
of the p2p device address. This is needed for p2p cert 6.1.9 to pass.
Signed-off-by: Madhan Mohan R <MadhanMohan.R@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-4-git-send-email-chi-hsien.lin@cypress.com
The firmware does not respond ARP request and causes ping failure with
following steps:
1. Bring up interface
ifconfig wlan0 up or start wpa_supplicant
2. Set the IP address
ifconfig wlan0 192.168.100.10
3. Bring down interface or
ifconfig wlan0 down or kill wpa_supplicant
4. Bring up interface again and set the same IP address
5. Connect to AP(192.168.100.1) and ping to AP will be failed.
FMAC clears arp_hostip when bringing down the interface, but not set it
back if setting the same IP address. We are able to see the IP address
in interface info(inconfig wlan0) but the ping still cannot work because
the firmware ARP offload does not respond the ARP request.
Because of that, we remove "arp_hostip_clear" from function
"brcmf_netdev_stop"
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-3-git-send-email-chi-hsien.lin@cypress.com
When starting station mode on wlan0 and AP mode on wlan1, the apsta will
be disabled and cause data stall on wlan0(station). The apsta feature
with MCHAN(Multi-Channel Concurrent) or RSDB(Real Simultaneous
Dual-Band) can make STA+AP work on two bands concurrently.
Because of that, we keep apsta enabled if firmware supports MCHAN or
RSDB features
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-2-git-send-email-chi-hsien.lin@cypress.com
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/stf.c:309:5-13:
Unneeded variable: "ret_code". Return "0" on line 328
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200413082126.22572-1-yanaijie@huawei.com
Sparse reports a warning at brcms_down()
warning: context imbalance in brcms_down()
- unexpected unlock
The root cause is the missing annotation at brcms_down()
Add the missing __must_hold(&wl->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200411001933.10072-6-jbi.octave@gmail.com
Sparse reports a warning at brcms_rfkill_set_hw_state()
warning: context imbalance in brcms_rfkill_set_hw_state()
- unexpected unlock
The root cause is the missing annotation at brcms_rfkill_set_hw_state()
Add the missing __must_hold(&wl->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200411001933.10072-5-jbi.octave@gmail.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3773:5-8:
Unneeded variable: "err". Return "0" on line 3781
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410090817.26883-1-yanaijie@huawei.com
This patch fixes commit 75388acd0c ("add mac80211-based driver for
legacy BCM43xx devices")
In https://bugzilla.kernel.org/show_bug.cgi?id=207093, a defect in
b43legacy is reported. Upon testing, thus problem exists on PPC and
X86 platforms, is present in the oldest kernel tested (3.2), and
has been present in the driver since it was first added to the kernel.
The problem is a corrupted channel status received from the device.
Both the internal card in a PowerBook G4 and the PCMCIA version
(Broadcom BCM4306 with PCI ID 14e4:4320) have the problem. Only Rev, 2
(revision 4 of the 802.11 core) of the chip has been tested. No other
devices using b43legacy are available for testing.
Various sources of the problem were considered. Buffer overrun and
other sources of corruption within the driver were rejected because
the faulty channel status is always the same, not a random value.
It was concluded that the faulty data is coming from the device, probably
due to a firmware bug. As that source is not available, the driver
must take appropriate action to recover.
At present, the driver reports the error, and them continues to process
the bad packet. This is believed that to be a mistake, and the correct
action is to drop the correpted packet.
Fixes: 75388acd0c ("add mac80211-based driver for legacy BCM43xx devices")
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested by: F. Erhard <erhard_f@mailbox.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200407190043.1686-1-Larry.Finger@lwfinger.net
Pointer 'address' is being assigned and updated in a few places
by it is never read. Hence the assignments are redundant and can
be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200405133906.381358-1-colin.king@canonical.com
sup_wpa feature is getting after setting feature_disable flag.
If firmware is supported sup_wpa feature, it's always enabled
regardless of feature_disable flag.
Fixes: b8a64f0e96 ("brcmfmac: support 4-way handshake offloading for WPA/WPA2-PSK")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200330052528.10503-1-jh80.chung@samsung.com
We add enable dynamic suspend (autosuspend) support in host driver, and
it can let platform cut down idle power consumption.
To support autosuspend feature in host driver, kernel need to be built
with CONFIG_USB_SUSPEND and autosuspend need to be turn on.
And we also replace wowl feature with adding "needs_remote_wakeup", so
that host still can be waken by wireless device.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-6-git-send-email-chi-hsien.lin@cypress.com
Will enable FMAC to push more packets to bus tx queue and help
improve throughput when fws queuing is enabled. This change is
required to tune the throughput for passing WMM CERT tests.
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-5-git-send-email-chi-hsien.lin@cypress.com
The function brcmf_inform_single_bss returns the value as success,
even when the length exceeds the maximum value.
The fix is to send appropriate code on this error.
This issue is observed when Cypress test group reported random fmac
crashes when running their tests and the path was identified from the
crash logs. With this fix the random failure issue in Cypress test group
was resolved.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-4-git-send-email-chi-hsien.lin@cypress.com
When the brcmf_fws_process_skb() fails to get hanger slot for
queuing the skb, it tries to free the skb.
But the caller brcmf_netdev_start_xmit() of that funciton frees
the packet on error return value.
This causes the double freeing and which caused the kernel crash.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-3-git-send-email-chi-hsien.lin@cypress.com
When the control transfer gets timed out, the error status
was returned without killing that urb, this leads to using
the same urb. This issue causes the kernel crash as the same
urb is sumbitted multiple times. The fix is to kill the
urb for timeout transfer before returning error
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-2-git-send-email-chi-hsien.lin@cypress.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200225020804.GA9428@embeddedor
