The container node in the iomuxc node is no longer necessary and causes
pinctl errors on the Ventana boards with analog video capture
since aa12693e41:
pinctrl core: initialized pinctrl subsystem
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/adv7180grp
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/ipu2_csi1grp
imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
imx6q-pinctrl 20e0000.iomuxc: function 'iomuxc' not supported
imx6q-pinctrl 20e0000.iomuxc: invalid function iomuxc in map table
imx6q-pinctrl 20e0000.iomuxc: function 'iomuxc' not supported
imx6q-pinctrl 20e0000.iomuxc: invalid function iomuxc in map table
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All of the Gateworks Ventana boards based on the IMX6 SoC except for the
GW54xx use the LTC3676 PMIC. Add a device-tree node with interrupt support
for this PMIC. Additionally remove the simple-bus notation in the regulator
nodes and any fixed regulators that are provided by the PMIC.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
bc677ff42e adds a device-tree property
to specify that an external watchdog reset is used to reset other
portions of the board and not just the IMX6 SoC.
This adds the property to the proper watchdog as well as the pinmux for
the Gateworks Ventana boards that use this external watchdog reset to
reset the PMIC which will reset all the PMIC power rails and not just
a chip-level IMX6 reset. This helps to work around various system issues
that can cause a hang when coming out of reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ventana boards have an off-board connector with signals that can be pinmuxed
as either GPIO or PWM. This patch adds pwm device-tree nodes in the disabled
state which the bootloader can decide to enable based on bootloader config.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
UHS-I support is available on Ventana boards with micro-SD sockets depending
on the board revision. To support this pinctl states for 100Mhz and 200MHz
must be added as well as pinmux of the VSELECT signal. In order to support
UHS-I the I/O rail of the 4-bit data bus must be switchable between 1.8V
and 3.3V.
By adding the no-1-8-v property, which disables UHS-I support, we allow the
bootloader to be in charge of selecting which boards have this capability
by removing that property if the board model/revision implement the support.
Additionally we will remove NANDF_CS1 here from the nand pinmux group as the
second chip-select is not used on any ventana boards and this is the pad
that is used for SD3_VELECT.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for the Gateworks GW5510 board featuring:
* i.MX6 SoC
* up to 512MB DDR3
* up to 2GB NAND flash
* 1x miniPCIe socket (with USB)
* HDMI out (micro-HDMI)
* HDMI in (micro-HDMI) (currently supported by only vendor kernel)
* TTL level I/O (supported by GW16111 breakout board):
* I2C
* 2x UART
* CAN
* 2x DIO (GPIO/PWM)
* USB OTG
For more details see:
http://www.gateworks.com/product/item/ventana-gw5510-single-board-computer
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
