BOSS RC-505 (shown by lsusb as "Roland Corp. RC-505") does require the
same quirk as these other BOSS devices.
Without this quirk it is neither possible to capture audio from nor to
write audio to the RC-505. Both just result in an empty audio
stream. With these changes both capture and playback seem to work
quite fine. MIDI funtionality was not tested.
Tested-by: Harry Reinold <harry.reinold@posteo.de>
Signed-off-by: Timon Reinold <tirei@agon.one>
Link: https://lore.kernel.org/r/20210102210835.21268-1-tirei@agon.one
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BOSS AD-10 requires the very same quirk like other BOSS devices to
enable the special implicit feedback mode.
Reported-and-tested-by: Martin Passing <martin@passing.name>
Link: https://lore.kernel.org/r/20201229083428.20467-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The calculation of in_cables and out_cables bitmaps are done with the
bit shift by the value from the descriptor, which is an arbitrary
value, and can lead to UBSAN shift-out-of-bounds warnings.
Fix it by filtering the bad descriptor values with the check of the
upper bound 0x10 (the cable bitmaps are 16 bits).
Reported-by: syzbot+92e45ae45543f89e8c88@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201223174557.10249-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The BOSS GT-1 (USB ID 0582:01d6) requires implicit feedback
like other similar BOSS devices. This patch adds this support.
[ rearranged the table entry in the ID order -- tiwai ]
Signed-off-by: Mike Oliphant <oliphant@nostatic.org>
Link: https://lore.kernel.org/r/20201221215533.2511-1-oliphant@nostatic.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some buggy firmware don't give the current sample rate but leaves
zero. Handle this case more gracefully without warning but just skip
the current rate verification from the next time.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201218145858.2357-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current channel-map control implementation in USB-audio driver may
lead to an error message like
"control 3:0:0:Playback Channel Map:0: access overflow"
when CONFIG_SND_CTL_VALIDATION is set. It's because the chmap get
callback clears the whole array no matter which count is set, and
rather the false-positive detection.
This patch fixes the problem by clearing only the needed array range
at usb_chmap_ctl_get().
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201211130048.6358-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Steinberg UR22 (with USB ID 0499:1509) requires the implicit feedback
for the proper playback, otherwise it causes occasional cracks.
This patch adds the corresponding the quirk table entry with the
recently added generic implicit fb support.
Reported-and-tested-by: Kilian <meschi@posteo.de>
Link: https://lore.kernel.org/r/20201209161835.13625-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another quirk for Pioneer DJ DDJ-SR2, which is quite similar like
other DJ DDJ models but with slightly different EPs or channels.
Reported-by: Geraldo <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/20201130083714.10640-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch allows the Pioneer DJ DDJ-RR to be seen as a USB audio
device under Linux and therefore usable in such applications as
Mixxx.
Tested Master Audio out, headphones (both output jacks) and microphone
input. All work perfectly.
Signed-off-by: Daniel Martin <dmanlfc@gmail.com>
Link: https://lore.kernel.org/r/20201128084035.2958-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the usb audio driver correctly finds implicit feedback endpoints,
the implicit feedback quirk for the MOTU M-Series is no longer required.
This also removes some unnecessary vendor specific messages from the MOTU
M-Series boot quirk. The removed vendor specific messages turned on vendor
specific interrupts to the host every 32 samples. The only thing the boot
quirk needs to do is wait for 2 seconds.
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Signed-off-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-42-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few other BOSS devices (BR-80, GT-100v2, Katana) seem requiring the
same quirk as BOSS GT-001, i.e. no implicit feedback for playback but
tying with capture. Add and correct the corresponding quirk table
entries for them.
Reported-and-tested-by: Keith Milner <kamilner@superlative.org>
Link: https://lore.kernel.org/r/20201123085347.19667-41-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A new module option, implicit_fb, is added to specify the driver
looking for the implicit feedback sync. This can be useful for a
device that could be working better in the implicit feed back mode and
user wants to test it quickly. When this works, we can add the quirk
entry easily.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-40-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch extends the implicit feedback mode parser code to check the
description more generically, so that the quirk entries can be added
without the explicit EP and interface numbers. The search is done for
the next and the previous interface of the given altset, and if both
entries are ASYNC mode and the direction matches, it just takes as the
sync endpoint. The generic parser is applicable only for the playback
stream.
As of now, only a few M-Audio devices have been converted to use this
mode.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-39-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The code dealing with the implicit feedback mode grew recently, and
it's becoming messy. As we receive more and more devices that need
the similar handling, it's better to be processed through a table
instead of the open code.
This patch moves the code that is relevant with parsing the implicit
feedback mode and some helpers into another file, implicit.c. The
detection and the setup of the implicit feedback sync EPs are
rewritten to use the ID/class matching table instead.
There should be no functional changes.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-38-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture stream of BOSS GT-001 seems always requiring to be tied
with the playback stream. OTOH, the playback stream of this device
doesn't seem working in the implicit fb mode, per se, since the
playback must be running before the capture stream.
This patch tries to address the points above:
- Avoid the implicit fb mode for the playback
- Set up a fake sync EP for the capture stream with the hard-coded
playback stream using the implicit fb mode
Reported-by: Keith Milner <kamilner@superlative.org>
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-37-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the sync endpoints have been parsed at the beginning and won't be
changed dynamically, let's show them in the proc outputs for helping
debugging.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-36-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just for consistency, use unsigned char for iface and altsetting in
allover places. Also rearrange the field positions of
snd_usb_endpiont and tidy up with some comments.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-35-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Follow the inclusive terminology, just replace sync_master/sync_slave
with sync_source/sync_sink. It's also a bit clearer from its meaning,
too.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-34-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are multiple places in format.c performing the similar code for
setting the rate_min, rate_max and rates fields. This patch unifies
those in a helper function and calls it at the end of the parser phase
so that all rate_table entries have been already determined.
No functional changes, just a minor code refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-33-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are two places calculating the next packet size for the playback
stream in the exactly same way. Provide the single helper for this
purpose and use it from both places gracefully.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-32-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some fields like interface and alt_idx in snd_usb_substream are mostly
useless now as they can be referred via either cur_audiofmt or
data_endpoint assigned to the substream. Drop those, and also assure
the concurrency about the access of cur_audiofmt field.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-31-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Minor code refactoring to consolidate the URB deactivation code in
endpoint.c. A slight behavior change is that the error handling in
snd_usb_endpoint_start() leaves EP_FLAG_STOPPING now. This should be
synced with the later PCM sync_stop callback.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-30-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The endpoint objects may be started/stopped concurrently by different
substreams in the case of implicit feedback mode, while the current
code handles the reference counter without any protection.
This patch changes the refcount to atomic_t for avoiding the
inconsistency. We need no reference_t here as the refcount goes only
up to 2.
Also the name "use_count" is renamed to "running" since this is about
actually the running status, not the open refcount.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-29-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The audioformat is referred in many places but most of usages are
read-only. Let's add const prefix in the possible places.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-28-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The implicit feedback mode uses a ring buffer for storing the received
packet sizes from the feedback source, and the code has a slight flaw;
when a playback stream stalls by some reason and the URBs aren't
processed, the next_packet FIFO might become empty, but the driver
can't distinguish whether it's empty or full because it's managed with
read_poss and write_pos.
This patch addresses those by changing the next_packet array
management. Instead of keeping read and write positions, now the head
position and the queued amount are kept. It's easier to understand
about the emptiness. Also, the URB active flag is now cleared before
calling queue_pending_output_urbs() for avoiding (theoretically)
possible inconsistency.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-27-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is an intensive surgery for the endpoint and stream management
for achieving more robust and clean code.
The goals of this patch are:
- More clear endpoint resource changes
- The interface altsetting control in a single place
Below are brief description of the whole changes.
First off, most of the endpoint operations are moved into endpoint.c,
so that the snd_usb_endpoint object is only referred in other places.
The endpoint object is acquired and released via the new functions
snd_usb_endpoint_open() and snd_usb_endpoint_close() that are called
at PCM hw_params and hw_free callbacks, respectively. Those are
ref-counted and EPs can manage the multiple opens.
The open callback receives the audioformat and hw_params arguments,
and those are used for initializing the EP parameters; especially the
endpoint, interface and altset numbers are read from there, as well as
the PCM parameters like the format, rate and channels. Those are
stored in snd_usb_endpoint object. If it's the secondary open, the
function checks whether the given parameters are compatible with the
already opened EP setup, too.
The coupling with a sync EP (including an implicit feedback sync) is
done by the sole snd_usb_endpoint_set_sync() call.
The configuration of each endpoint is done in a single shot via
snd_usb_endpoint_configure() call. This is the place where most of
PCM configurations are done. A few flags and special handling in the
snd_usb_substream are dropped along with this change.
A significant difference wrt the configuration from the previous code
is the order of USB host interface setups. Now the interface is
always disabled at beginning and (re-)enabled at the last step of
snd_usb_endpoint_configure(), in order to be compliant with the
standard UAC2/3. For UAC1, the interface is set before the parameter
setups since there seem devices that require it (e.g. Yamaha THR10),
just like how it was done in the previous driver code.
The start/stop are almost same as before, also single-shots. The URB
callbacks need to be set via snd_usb_endpoint_set_callback() like the
previous code at the trigger phase, too.
Finally, the flag for the re-setup is set at the device suspend
through the full EP list, instead of PCM trigger. This catches the
overlooked cases where the PCM hasn't been running yet but the device
needs the full setup after resume.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-26-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function to evaluate the match of the parameters with an EP
assumes only the discrete rate tables and doesn't handle the
continuous rates properly.
This patch fixes match_endpoint_audioformats() to handle the
continuous rates. Also the almost useless debug prints there are
dropped.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-25-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 92adc96f8e ("ALSA: usb-audio: set the interface format
after resume on Dell WD19") introduced the workaround for the broken
setup after the resume specifically on a Dell dock model. However,
the full setup should have been performed after the resume on all
devices, as we can't guarantee the same state. So this patch removes
the conditional check and applies the workaround always.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-24-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The prepare_data_urb and retire_data_urb fields of the endpoint object
are set dynamically at PCM trigger start/stop. Those are evaluated in
the endpoint handler, but there can be a race, especially if two
different PCM substreams are handling the same endpoint for the
implicit feedback case. Also, the data_subs field of the endpoint is
set and accessed dynamically, too, which has the same risk.
As a slight improvement for the concurrency, this patch introduces the
function to set the callbacks and the data in a shot with the memory
barrier. In the reader side, it's also fetched with the memory
barrier.
There is still a room of race if prepare and retire callbacks are set
during executing the URB completion. But such an inconsistency may
happen only for the implicit fb source, i.e. it's only about the
capture stream. And luckily, the capture stream never sets the
prepare callback, hence the problem doesn't happen practically.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-23-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
start_endpoints() may leave the data endpoint running if an error
happens at starting the sync endpoint. We should stop both streams
properly, instead.
While we're at it, move the debug prints into the endpoint.c that is a
more suitable place.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-22-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary change for the later big changes. This is a minor code
refactoring to drop the unnecessary arguments that can be retrieved in
a different way.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-21-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary change for the later big changes. This is a minor code
refactoring to drop the unnecessary arguments that can be retrieved in
a different way.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-20-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary patch for the later big change. Just a minor code
refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-19-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Setting the active altsetting at changing sample rate seems
unrecommended. The host should deselect the altsetting at first
before that, then select it again.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-18-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a helper function to retrieve the usb_host_interface object from
the given interface and altsetting number pair, which is a commonly
used procedure in the driver code.
No functional changes, just minor code refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-17-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This behavior turned out to be invalid from the USB spec POV and
shouldn't be applied. As it's an optional flag that is set only via
an card control element that must be hardly used, let's drop it
again.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-16-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently snd_usb_endpoint objects are created at first when the
substream is opened and tries to assign the endpoints corresponding to
the matching audioformat. But since basically the all endpoints have
been already parsed and the information have been obtained, we may
create the endpoint objects statically at the init phase. It's easier
to manage for the implicit fb case, for example.
This patch changes the endpoint object management and lets the parser
to create the all endpoint objects.
This change shouldn't bring any functional changes.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-15-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The implicit feedback mode initializes both the main data stream and
the sync data stream. When a sync stream was already opened, this
would result in the doubly initialization and might screw up things.
Add the check of already opened sync streams and skip the unnecessary
initialization.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-14-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The file debug.h contains a simple macro for debug prints, and it's
used only in two places, the format parser and the hw_params rules.
The former actually should print a more informative message instead,
so the only users are the hw_parmas rules.
This patch moves the contents of debug.h into the hw_params rules
local code and remove the unneeded includes. Also, the debug print in
the format parser is replaced with the information print with more
useful information, and the raw printk() call is replaced with
pr_debug().
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-13-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Several hw_params functions narrows the interval via min/max rule in
the very similar way, so factor out those into a helper function and
use commonly.
No functional changes, just minor code refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-12-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current code, there is no check at the stream open time whether
the endpoint is being already used by others. In the normal
operations, this shouldn't happen, but in the case of the implicit
feedback mode, it's a common problem with the full duplex operation,
because the capture stream is always opened by the playback stream as
an implicit sync source.
Although we recently introduced the check of such a conflict of
parameters at the PCM hw_params time, it doesn't give any hint at the
hw_params itself and just gives the error. This isn't quite
comfortable, and it caused problems on many applications.
This patch attempts to make the parameter handling easier by
introducing the strict hw constraint matching with the counterpart
stream that is being used. That said, when an implicit feedback
playback stream is running before a capture stream is opened, the
capture stream carries the PCM hw-constraint to allow only the same
sample rate, format, periods and period frames as the running playback
stream. If not opened or there is no conflict of endpoints, the
behavior remains as same as before.
Note that this kind of "weak link" should work for most cases, but
this is no concrete solution; e.g. if an application changes the hw
params multiple times while another stream is opened, this would lead
to inconsistencies.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-11-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preliminary work for the upcoming hw-constraint change for
the implicit feedback mode.
Currently snd_usb_autoresume() is called at the end of
setup_hwinfo(). It's a bit confusing; because of this implicit
refcount usage, the caller side needs to call snd_usb_autosuspend()
later in the error path although it's not seen inside the function.
Instead, it's clearer to call both snd_usb_autoresume() and suspend()
in the very same function.
It's only refactoring and no functional changes.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of parsing and evaluating the sync endpoint and the implicit
feedback mode at each time the audio stream is opened, let's parse it
once at the probe time, as the all needed information can be obtained
statically from the descriptor or from the quirk.
This patch extends audioformat struct to record the sync endpoint,
interface and altsetting as well as the implicit feedback flag, which
are filled at parsing the streams. Then, set_sync_endpoint() is much
simplified just to follow the already parsed data.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few rooms for improvements wrt the debug prints:
- The EP debug print is shown only at starting, not at stopping
- The EP debug print contains useless object addresses
- Some helpers show the urb and the EP object addresses, too
This patch addresses those shortcomings.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The sync EP setup isn't cleared at stopping the stream but expected to
be cleared at the next stream start. This may leave the sync link
setup stale and can spoof wrongly when full duplex streams were
running in the implicit fb sync. Let's initialize them properly at
start and end of the stream.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
