Commit 63aa945b10 ("memory: omap-gpmc: Add Kconfig option for debug")
unified the GPMC debug for the SoCs with GPMC. The commit also left out
the option for HWMOD_INIT_NO_RESET as we now require proper timings for
GPMC to be able to remap GPMC devices out of address 0.
Unfortunately on Nokia N900, onenand now only partially works with the
device tree provided timings. It works enough to get detected but the
clock rate supported by the onenand chip gets misdetected. This in turn
causes the GPMC timings to be miscalculated and this leads into file
system corruption on N900.
Looks like onenand needs CS_CONFIG1 bit 27 WRITETYPE set for for sync
write. This is needed also for async timings when we write to onenand
with omap2_onenand_set_async_mode(). Without sync write bit set, the
async read for the onenand ONENAND_REG_VERSION_ID will return 0xfff.
Let's exit with an error if onenand rate is not detected. And let's
remove the extra call to omap2_onenand_set_async_mode() as we only need
to do this once at the end of omap2_onenand_setup_async().
Fixes: 63aa945b10 ("memory: omap-gpmc: Add Kconfig option for debug")
Cc: stable@vger.kernel.org # v4.2+
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make sure to tell the kernel that AM437x devices have ARM TWD timer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[grygorii.strashko@ti.com: drop ARM Global timer selection, because
it's incompatible with PM (cpuidle/cpufreq). So, it's unsafe to enable
it unconditionally]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
System will misbehave in the following case:
- AM43XX only build (UP);
- CONFIG_CPU_IDLE=y
- ARM TWD timer enabled and selected as clockevent device.
In the above case, It's expected that broadcast timer will be used as
backup timer when CPUIdle will put MPU in low power states where ARM
TWD will stop and lose its context. But, the CONFIG_SMP might not be
selected when kernel is built for AM43XX SoC only and, as result,
GENERIC_CLOCKEVENTS_BROADCAST option will not be selected also. This
will break CPUIdle and System will stuck in low power states.
Hence, fix it by selecting GENERIC_CLOCKEVENTS_BROADCAST option for
AM43XX SoCs always and add empty tick_broadcast() function
implementation - no need to send any IPI on UP. After this change
timer1 will be selected as broadcast timer the same way as for SMP,
and CPUIdle will work properly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable REGULATOR_FIXED_VOLTAGE for all OMAP2+ platforms
otherwise system can't boot from SD-card when kernel is
built for single SoC (for example, with CONFIG_SOC_DRA7XX=y only).
It's also required for almost all TI SoC's platforms.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP CPU hotplug uses cpu1's clocks and power domains for CPU1 wake up
from low power states (or turn on CPU1). This part of code is also
part of system suspend (disable_nonboot_cpus()).
>From other side, cpu1's clocks and power domains are used by CPUIdle. All above
functionality is mutually exclusive and, therefore, lockless clkdm/pwrdm api
can be used in omap4_boot_secondary().
This fixes below back-trace on -RT which is triggered by
pwrdm_lock/unlock():
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 1, irqs_disabled(): 0, pid: 118, name: sh
9 locks held by sh/118:
#0: (sb_writers#4){.+.+.+}, at: [<c0144a6c>] vfs_write+0x13c/0x164
#1: (&of->mutex){+.+.+.}, at: [<c01b4c70>] kernfs_fop_write+0x48/0x19c
#2: (s_active#24){.+.+.+}, at: [<c01b4c78>] kernfs_fop_write+0x50/0x19c
#3: (device_hotplug_lock){+.+.+.}, at: [<c03cbff0>] lock_device_hotplug_sysfs+0xc/0x4c
#4: (&dev->mutex){......}, at: [<c03cd284>] device_online+0x14/0x88
#5: (cpu_add_remove_lock){+.+.+.}, at: [<c003af90>] cpu_up+0x50/0x1a0
#6: (cpu_hotplug.lock){++++++}, at: [<c003ae48>] cpu_hotplug_begin+0x0/0xc4
#7: (cpu_hotplug.lock#2){+.+.+.}, at: [<c003aec0>] cpu_hotplug_begin+0x78/0xc4
#8: (boot_lock){+.+...}, at: [<c002b254>] omap4_boot_secondary+0x1c/0x178
Preemption disabled at:[< (null)>] (null)
CPU: 0 PID: 118 Comm: sh Not tainted 4.1.12-rt11-01998-gb4a62c3-dirty #137
Hardware name: Generic DRA74X (Flattened Device Tree)
[<c0017574>] (unwind_backtrace) from [<c0013be8>] (show_stack+0x10/0x14)
[<c0013be8>] (show_stack) from [<c05a8670>] (dump_stack+0x80/0x94)
[<c05a8670>] (dump_stack) from [<c05ad158>] (rt_spin_lock+0x24/0x54)
[<c05ad158>] (rt_spin_lock) from [<c0030dac>] (clkdm_wakeup+0x10/0x2c)
[<c0030dac>] (clkdm_wakeup) from [<c002b2c0>] (omap4_boot_secondary+0x88/0x178)
[<c002b2c0>] (omap4_boot_secondary) from [<c0015d00>] (__cpu_up+0xc4/0x164)
[<c0015d00>] (__cpu_up) from [<c003b09c>] (cpu_up+0x15c/0x1a0)
[<c003b09c>] (cpu_up) from [<c03cd2d4>] (device_online+0x64/0x88)
[<c03cd2d4>] (device_online) from [<c03cd360>] (online_store+0x68/0x74)
[<c03cd360>] (online_store) from [<c01b4ce0>] (kernfs_fop_write+0xb8/0x19c)
[<c01b4ce0>] (kernfs_fop_write) from [<c0144124>] (__vfs_write+0x20/0xd8)
[<c0144124>] (__vfs_write) from [<c01449c0>] (vfs_write+0x90/0x164)
[<c01449c0>] (vfs_write) from [<c01451e4>] (SyS_write+0x44/0x9c)
[<c01451e4>] (SyS_write) from [<c0010240>] (ret_fast_syscall+0x0/0x54)
CPU1: smp_ops.cpu_die() returned, trying to resuscitate
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing HWMOD_NO_IDLEST hwmod flag for entries not
having omap4 clkctrl values.
The emac0 hwmod flag fixes the davinci_emac driver probe
since the return of pm_resume() call is now checked.
This solves the following boot errors :
[ 0.121429] omap_hwmod: l4_ls: _wait_target_ready failed: -16
[ 0.121441] omap_hwmod: l4_ls: cannot be enabled for reset (3)
[ 0.124342] omap_hwmod: l4_hs: _wait_target_ready failed: -16
[ 0.124352] omap_hwmod: l4_hs: cannot be enabled for reset (3)
[ 1.967228] omap_hwmod: emac0: _wait_target_ready failed: -16
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is not needed anymore. Handling a potentially pending imprecise external
abort left behind by the bootloader is now done in a slightly safer way inside
the common ARM startup code.
With the recent changes to abort handling, this issue got fixed by 57df538085
("ARM: OMAP2+: Fix imprecise external abort caused by bogus SRAM init").
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[tony@atomide.com: updated comments to describe what fixed the issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>
McASP3 is used by default on DRA7x based boards for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some module needs more than one functional clock in order to be accessible,
like the McASPs found in DRA7xx family.
This flag will indicate that the opt_clks need to be handled at the same
time as the main_clk for the given hwmod, ensuring that all needed clocks
are enabled before we try to access the module's address space.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Again we have a sizable (but not huge) cleanup branch with a net delta of about
-3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now gone
completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the above are
the major pieces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uI7R
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"Again we have a sizable (but not huge) cleanup branch with a net delta
of about -3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now
gone completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board
file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the
above are the major pieces"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
ARM: Remove __ref on hotplug cpu die path
ARM: Remove open-coded version of IRQCHIP_DECLARE
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
...
This time we have a very typical update which is mostly fixes and updates to
drivers and no new drivers.
- Biggest change is coming from Peter for edma cleanup which even caused
some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tIzO
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have a very typical update which is mostly fixes and
updates to drivers and no new drivers.
- the biggest change is coming from Peter for edma cleanup which even
caused some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac"
* tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (77 commits)
dmaengine: edma: Add dummy driver skeleton for edma3-tptc
Revert "ARM: DTS: am33xx: Use the new DT bindings for the eDMA3"
Revert "ARM: DTS: am437x: Use the new DT bindings for the eDMA3"
dmaengine: dw: some Intel devices has no memcpy support
dmaengine: dw: platform: provide platform data for Intel
dmaengine: dw: don't override platform data with autocfg
dmaengine: hdmac: Add scatter-gathered memset support
dmaengine: hdmac: factorise memset descriptor allocation
dmaengine: virt-dma: Fix kernel-doc annotations
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: New device tree binding
dmaengine: Kconfig: edma: Select TI_DMA_CROSSBAR in case of ARCH_OMAP
dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx
dmaengine: edma: Merge the of parsing functions
dmaengine: edma: Do not allocate memory for edma_rsv_info in case of DT boot
dmaengine: edma: Refactor the dma device and channel struct initialization
dmaengine: edma: Get qDMA channel information from HW also
dmaengine: edma: Merge map_dmach_to_queue into assign_channel_eventq
dmaengine: edma: Correct PaRAM access function names (_parm_ to _param_)
...
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface)
and a few fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2)
support along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated
by the specification) to avoid confusion on systems with more than
255 logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges
on x86 and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when
it has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume
handling in some cases and the changes include a couple of users
of it (the i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up
the system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that
code (Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common
cpufreq policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states
range to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization
to make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=1gaH
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"Quite a new features are included this time.
First off, the Collaborative Processor Performance Control interface
(version 2) defined by ACPI will now be supported on ARM64 along with
a cpufreq frontend for CPU performance scaling.
Second, ACPI gets a new infrastructure for the early probing of IRQ
chips and clock sources (along the lines of the existing similar
mechanism for DT).
Next, the ACPI core and the generic device properties API will now
support a recently introduced hierarchical properties extension of the
_DSD (Device Specific Data) ACPI device configuration object. If the
ACPI platform firmware uses that extension to organize device
properties in a hierarchical way, the kernel will automatically handle
it and make those properties available to device drivers via the
generic device properties API.
It also will be possible to build the ACPICA's AML interpreter
debugger into the kernel now and use that to diagnose AML-related
problems more efficiently. In the future, this should make it
possible to single-step AML execution and do similar things.
Interesting stuff, although somewhat experimental at this point.
Finally, the PM core gets a new mechanism that can be used by device
drivers to distinguish between suspend-to-RAM (based on platform
firmware support) and suspend-to-idle (or other variants of system
suspend the platform firmware is not involved in) and possibly
optimize their device suspend/resume handling accordingly.
In addition to that, some existing features are re-organized quite
substantially.
First, the ACPI-based handling of PCI host bridges on x86 and ia64 is
unified and the common code goes into the ACPI core (so as to reduce
code duplication and eliminate non-essential differences between the
two architectures in that area).
Second, the Operating Performance Points (OPP) framework is
reorganized to make the code easier to find and follow.
Next, the cpufreq core's sysfs interface is reorganized to get rid of
the "primary CPU" concept for configurations in which the same
performance scaling settings are shared between multiple CPUs.
Finally, some interfaces that aren't necessary any more are dropped
from the generic power domains framework.
On top of the above we have some minor extensions, cleanups and bug
fixes in multiple places, as usual.
Specifics:
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface) and a few
fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2) support
along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated by
the specification) to avoid confusion on systems with more than 255
logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges on x86
and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when it
has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume handling
in some cases and the changes include a couple of users of it (the
i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up the
system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that code
(Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common cpufreq
policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states range
to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization to
make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes)"
* tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (108 commits)
cpufreq: postfix policy directory with the first CPU in related_cpus
cpufreq: create cpu/cpufreq/policyX directories
cpufreq: remove cpufreq_sysfs_{create|remove}_file()
cpufreq: create cpu/cpufreq at boot time
cpufreq: Use cpumask_copy instead of cpumask_or to copy a mask
cpufreq: ondemand: Drop unnecessary locks from update_sampling_rate()
PM / Domains: Merge measurements for PM QoS device latencies
PM / Domains: Don't measure ->start|stop() latency in system PM callbacks
PM / clk: Fix broken build due to non-matching code and header #ifdefs
ACPI / Documentation: add copy_dsdt to ACPI format options
ACPI / sysfs: correctly check failing memory allocation
ACPI / video: Add a quirk to force native backlight on Lenovo IdeaPad S405
ACPI / CPPC: Fix potential memory leak
ACPI / CPPC: signedness bug in register_pcc_channel()
ACPI / PAD: power_saving_thread() is not freezable
ACPI / PM: Fix incorrect wakeup IRQ setting during suspend-to-idle
ACPI: Using correct irq when waiting for events
ACPI: Use correct IRQ when uninstalling ACPI interrupt handler
cpuidle: mvebu: disable the bind/unbind attributes and use builtin_platform_driver
cpuidle: mvebu: clean up multiple platform drivers
...
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- Rework the irqdomain core infrastructure to accomodate ACPI based
systems. This is required to support ARM64 without creating
artificial device tree nodes.
- Sanitize the ACPI based ARM GIC initialization by making use of the
new firmware independent irqdomain core
- Further improvements to the generic MSI management
- Generalize the irq migration on CPU hotplug
- Improvements to the threaded interrupt infrastructure
- Allow the migration of "chained" low level interrupt handlers
- Allow optional force masking of interrupts in disable_irq[_nosysnc]
- Support for two new interrupt chips - Sigh!
- A larger set of errata fixes for ARM gicv3
- The usual pile of fixes, updates, improvements and cleanups all
over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
Document that IRQ_NONE should be returned when IRQ not actually handled
PCI/MSI: Allow the MSI domain to be device-specific
PCI: Add per-device MSI domain hook
of/irq: Use the msi-map property to provide device-specific MSI domain
of/irq: Split of_msi_map_rid to reuse msi-map lookup
irqchip/gic-v3-its: Parse new version of msi-parent property
PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Add support code for multi-parent version of "msi-parent"
irqchip/gic-v3-its: Add handling of PCI requester id.
PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
of/irq: Add new function of_msi_map_rid()
Docs: dt: Add PCI MSI map bindings
irqchip/gic-v2m: Add support for multiple MSI frames
irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
irqchip/mxs: Add Alphascale ASM9260 support
irqchip/mxs: Prepare driver for hardware with different offsets
irqchip/mxs: Panic if ioremap or domain creation fails
irqdomain: Documentation updates
irqdomain/msi: Use fwnode instead of of_node
...
bit of time sorting out regressions for v4.3 and are very late with
these, I've kept the changes down to minimum:
- A series of timer changes from Felipe Balbi to get us closer to
moving the remaining timer code into drivers
- A series of hwmod clean-up changes queued by Paul Walmsley
- SoC detection clean-up to use soc_is instead of cpu_is as CPU is
within the SoC and is confusing naming. The rest we can now change
along with the other clean-up
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWK9AkAAoJEBvUPslcq6VzwIQQAKFH1N3+n0PQ+LGvpuq/fpr6
0WE5N1xEhrzZ/5xJKlJVgtpvM2g3habjyxr9wmLcbRlhZUPefk5q+J3OHOlAhN8u
E2+9k0VGg5O8xQH+hjkEVyjxGIUjXpq2pvs4WebIC61mP/Plu8TlFQSc2gfQJs97
DfjaZeMO1cf05wt+rWbNrIjyy/qIz3ndV6r19tQq0WxwV0dfIXR6G4zxJZnbA+9N
9h8jd49/3dHdEQFVqPUVw5GEw5AhKDBKDmuHNYejkid0cMKi+v130+6P4S9s7kq3
bbWyRTjX+LvJs6POKBvbJ4Kn9nBKfF2OLoByEguCNoC06R8KxDJV63V0bcE7VK/R
i6Rk9ldBpiWxALBbFAts9r4ldWzIANyrUqwLj8nbqDvGvfLaLW1lYrFWCC1j3+vu
PXqGG8KLmLhepbzo6oiQ91PD1XFrKZNyBMptB5rZqOv/YyZ57xoM5WjUXTolRC1a
k/iH6t9jsAddyCr+ZgUXsIP71jJ8IKRn2U+0/ycME1OSIaokpGydOnqL26g+69ca
VYpwKSeja+nO4FYeGR2MRvkKgJFoh1Be44Vk7wtjUpJSmScAioI2poblkI/4k8vK
mD54I8RIInaq/i8FrcVIYq04Nm+nHvC4MyQ/T1NJgl3iysiEcdTYxYDM+XwmVvZA
m4yweJz+mO36aIX82srw
=gNfn
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/soc-clean-up' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Minimal omap SoC changes for v4.4 merge window. As we've spent quite a
bit of time sorting out regressions for v4.3 and are very late with
these, I've kept the changes down to minimum:
- A series of timer changes from Felipe Balbi to get us closer to
moving the remaining timer code into drivers
- A series of hwmod clean-up changes queued by Paul Walmsley
- SoC detection clean-up to use soc_is instead of cpu_is as CPU is
within the SoC and is confusing naming. The rest we can now change
along with the other clean-up
* tag 'omap-for-v4.4/soc-clean-up' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
arm: omap2: timer: provide generic sync32k_timer_init function
arm: omap2: timer: remove __omap_gptimer_init()
arm: omap2: timer: add a gptimer argument to sync32k_timer_init()
arm: omap2: timer: get rid of obfuscating macros
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove some superfluous data from the OMAP2+ hwmod data files. Mostly
this is a result of data being moved to DT files. Nothing too
controversial, here.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/hwmod-cleanup-a-for-v4.4/20151023130140/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AVI9
-----END PGP SIGNATURE-----
Merge tag 'for-v4.4/omap-hwmod-cleanup-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.4/soc
ARM: OMAP2+: hwmod cleanup for v4.4
Remove some superfluous data from the OMAP2+ hwmod data files. Mostly
this is a result of data being moved to DT files. Nothing too
controversial, here.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/hwmod-cleanup-a-for-v4.4/20151023130140/
Remove the mailbox attribute data, irq info and hwmod addr space
data that are used for creating the legacy-style mailbox devices,
there is no need for these as the support for legacy-mode for this
IP is being dropped.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The legacy-style device creation logic for hwspinlock
has been removed after the DT-support was added to the
driver. The hwmod addr space for spinlock is therefore
no longer needed, so remove it.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The legacy-style device creation logic for hwspinlock
has been removed after the DT-support was added to the
driver. The hwmod addr space for spinlock is therefore
no longer needed, so remove it.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
GPMC address information is provided by device tree. No longer need
to include this information within hwmod.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[paul@pwsan.com: fixed chip names in subject line]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Now that __cpuinit has been removed, the __ref markings on these
functions are useless. Remove them. This also reduces the size of
the multi_v7_defconfig image:
$ size before after
text data bss dec hex filename
12683578 1470996 348904 14503478 dd4e36 before
12683274 1470996 348904 14503174 dd4d06 after
presumably because now we don't have to jump to code in the
.ref.text section and/or the noinline marking is removed.
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <linux-omap@vger.kernel.org>
Cc: <linux-arm-msm@vger.kernel.org>
Cc: <spear-devel@list.st.com>
Cc: <linux-tegra@vger.kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Barry Song <baohua@kernel.org>
Acked-by: Andy Gross <agross@codeaurora.org>
Acked-by: Viresh Kumar <vireshk@kernel.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that the IRQCHIP_DECLARE macro has been moved to linux/irqchip.h,
it becomes possible to cleanup the open-coded versions of the same
macro that have been added to some private irqchips implementations.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Kukjin Kim <kgene@kernel.org>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
AM437x-based boards, can use omap4_local_timer_init()
just fine. Let's use that instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ELM address information is provided by device tree. No longer need
to include this information within hwmod.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[paul@pwsan.com: fixed chip names in subject line; dropped the OMAP4 section
since the OMAP4 SoC DTS file doesn't have the ELM address space documented
yet]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit b483a4a5a7 ("ARM: OMAP4+: hwmod data: Don't prevent RESET of
USB Host module") added the SYSC_HAS_RESET_STATUS flag to both OMAP4
and OMAP5 USB host module hwmon sysconfig but that flag was already
set for OMAP5. So now the flag appears twice in the expression.
make coccicheck complains with the following message:
omap_hwmod_54xx_data.c:1846:37-58: duplicated argument to & or |
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some omaps are producing imprecise external aborts because we are
wrongly trying to init SRAM for device tree based booting. Only
omap3 is still using the legacy SRAM code, so we need to make it
omap3 specific. Otherwise we can get errors like this on at least
dm814x:
Unhandled fault: imprecise external abort (0xc06) at 0xc08b156c
...
(omap_rev) from [<c08b12e0>] (omap_sram_init+0xf8/0x3e0)
(omap_sram_init) from [<c08aca0c>] (omap_sdrc_init+0x10/0xb0)
(omap_sdrc_init) from [<c08b581c>] (pdata_quirks_init+0x18/0x44)
(pdata_quirks_init) from [<c08b5478>] (omap_generic_init+0x10/0x1c)
(omap_generic_init) from [<c08a57e0>] (customize_machine+0x1c/0x40)
(customize_machine) from [<c00098a4>] (do_one_initcall+0x80/0x1dc)
(do_one_initcall) from [<c08a2ec4>] (kernel_init_freeable+0x218/0x2e8)
(kernel_init_freeable) from [<c063a554>] (kernel_init+0x8/0xec)
(kernel_init) from [<c000f890>] (ret_from_fork+0x14/0x24)
Let's fix the issue by making sure omap_sdrc_init only gets called for
omap3. To do that, we need to have compatible "ti,omap3" in the dts
files. And let's also use "ti,omap3630" instead of "ti,omap36xx" like
we're supposed to.
Signed-off-by: Tony Lindgren <tony@atomide.com>
On boards with more than 2GB of RAM booting goes wrong with things not
working and we're getting lots of l3 warnings:
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x260/0x384()
44000000.ocp:L3 Custom Error: MASTER MMC6 TARGET DMM1 (Idle):
Data Access in User mode during Functional access
...
[<c044e158>] (scsi_add_host_with_dma) from [<c04705c8>]
(ata_scsi_add_hosts+0x5c/0x18c)
[<c04705c8>] (ata_scsi_add_hosts) from [<c046b13c>]
(ata_host_register+0x150/0x2cc)
[<c046b13c>] (ata_host_register) from [<c046b38c>]
(ata_host_activate+0xd4/0x124)
[<c046b38c>] (ata_host_activate) from [<c047f42c>]
(ahci_host_activate+0x5c/0x194)
[<c047f42c>] (ahci_host_activate) from [<c0480854>]
(ahci_platform_init_host+0x1f0/0x3f0)
[<c0480854>] (ahci_platform_init_host) from [<c047c9dc>]
(ahci_probe+0x70/0x98)
[<c047c9dc>] (ahci_probe) from [<c04220cc>]
(platform_drv_probe+0x54/0xb4)
Let's fix the issue by enabling ZONE_DMA for LPAE. Note that we need to
limit dma_zone_size to 2GB as the rest of the RAM is beyond the 4GB limit.
Let's also fix things for dra7 as done in similar patches in the TI tree
by Lokesh Vutla <lokeshvutla@ti.com>.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently apart from dra7, omap5 and amx3 all the other SoCs
are identified using cpu_is_* functions which is not right since
they are all SoCs(System on Chips). Hence changing the SoC
identification code to use soc_is instead of cpu_is and keeping
defines for cpu_is where needed. This allows us to replace the
rest of cpu_is usage along with other fixes as needed.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Keerthy <j-keerthy@ti.com>
[tony@atomide.com: reworked the soc.h changes to minimum]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The naming for the cpu_is macros is confusing as the CPU is separate
and within the SoC. Let's rename all the macros to soc_is, and let's
define cpu_is also for the ones still in use. Then we can just remove
the cpu_is macros once the users are fixed up.
To keep the chances of breaking anything, the changes were
generated with the following regular expressions:
s/cpu_is/soc_is/g
s/CPU/SoC/g
Then the list of existing cpu_is users was generated with:
$ $ grep -o -e 'cpu_is_.\+()' arch/arm/mach-omap2/*.[chS] | \
cut -d: -f2 | sort | uniq
And added to the end of the soc.h.
I decided to rework the earlier patches by Keerthy <j-keerthy@ti.com>
to keep changes down to minimum to avoid potential errors and stick
to just search and replace.
Signed-off-by: Tony Lindgren <tony@atomide.com>
now that we have a working 32k clocksource driver,
we can limit HWMOD usage to non-DT boots and rely
on clocksource_of_init() every time we boot
with DT.
While at that, also make sure that we don't disable
the 32-counter device so it gets probed by its driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this function is not only about the 32k sync
timer, it's OMAP's generic init_time implementation.
Let's rename it to make that detail easier to
notice.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If booting with DT, let's make sure to always
call clocksource_of_init() as this will make
it easier to move timer code to drivers/clocksource
in the future.
Signed-off-by: Felipe Balbi <balbi@ti.com>
instead of constantly defining a small wrapper
around __omap_sync32k_timer_init(), let's define
a generic one which can be used by all OMAPs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
__omap_sync32k_timer_init(), now takes the clock
source as a parameter. This means we no longer need
__omap_gptimer_init().
Note that __omap_sync32k_timer_init() will be
renamed in a follow-up patch as it's not longer 32k
source specific.
Signed-off-by: Felipe Balbi <balbi@ti.com>
as it turns out, __omap_gptimer_init() and
__omap_sync32k_timer_init() are essentially
the same thing, but __omap_gptimer_init() wants
to always use gptimer.
Instead of forcing all those devices to pass
a use_gptimer cmdline argument, we add a new
function argument to __omap_sync32k_timer_init()
in preparation to deleting __omap_gptimer_init().
On a follow-up patch, we will remove uses of
__omap_gptimer_init() and replace them with
__omap_sync32k_timer_init() and pass the last
argument as true.
Signed-off-by: Felipe Balbi <balbi@ti.com>
those macros just make it a lot more difficult
to grep around and actually find similarities.
In this patch, we will simply remove them and
replace with actual functions and later commits
will come to further clean this up.
Signed-off-by: Felipe Balbi <balbi@ti.com>
omap4_local_timer_init() can be used by other
platforms as is. At least AM437x wants to use
it. Instead of making omap4-only and providing
a stub for builds without OMAP4, we can just
make sure that function is always available
for all SoCs that need it.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the OMAP3 core DPLL re-program code, and the associated SRAM
code that does the low-level programming of the DPLL divider, idling
of the SDRAM etc.
This code was never fully implemented in the kernel; things missing
were driver side handling of core clock changes (they need to account
for their functional clock rate being changed on-the-fly), and the whole
framework required for handling this. Thus, there is not much point
to keep carrying the low-level support code either.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the code out from arch/arm/common and merge it inside of the dmaengine
driver.
This change is done with as minimal (if eny) functional change to the code
as possible to avoid introducing regression.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we now have a generic data structure to express an
interrupt specifier, convert all hierarchical irqchips that
are OF based to use a fwnode_handle as part of their alloc
and xlate (which becomes translate) callbacks.
As most of these drivers have dependencies (they exchange IRQ
specifiers), change them all in a single, massive patch...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-6-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The struct irq_domain contains a "struct device_node *" field
(of_node) that is almost the only link between the irqdomain
and the device tree infrastructure.
In order to prepare for the removal of that field, convert all
users to use irq_domain_get_of_node() instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The cpuidle tracepoints are called within a rcu_idle_exit() section, and
must be denoted with the _rcuidle() version of the tracepoint.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the unneded semicolons since they are clearly a typo error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRM_POLCTRL_TWL_MASK and PRM_POLCTRL_TWL_MASK
macros are not used so they can be deleted.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 ISP is now fully supported in DT, remove its instantiation
from C code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
