IPsec crypto offload current Software Parser (SWP) fields settings in
the ethernet segment (eseg) are not aligned with PRM/HW expectations.
Among others in case of IP|ESP|TCP packet, current driver sets the
offsets for inner_l3 and inner_l4 although there is no inner l3/l4
headers relative to ESP header in such packets.
SWP provides the offsets for HW ,so it can be used to find csum fields
to offload the checksum, however these are not necessarily used by HW
and are used as fallback in case HW fails to parse the packet, e.g
when performing IPSec Transport Aware (IP | ESP | TCP) there is no
need to add SW parse on inner packet. So in some cases packets csum
was calculated correctly , whereas in other cases it failed. The later
faced csum errors (caused by wrong packet length calculations) which
led to lots of packet drops hence the low throughput.
Fix by setting the SWP fields as expected in a IP|ESP|TCP packet.
the following describe the expected SWP offsets:
* Tunnel Mode:
* SWP: OutL3 InL3 InL4
* Pkt: MAC IP ESP IP L4
*
* Transport Mode:
* SWP: OutL3 OutL4
* Pkt: MAC IP ESP L4
*
* Tunnel(VXLAN TCP/UDP) over Transport Mode
* SWP: OutL3 InL3 InL4
* Pkt: MAC IP ESP UDP VXLAN IP L4
Fixes: f1267798c9 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
During suspend flow the driver calls mlx5e_destroy_vlan_table() which
does not only delete the vlans steering flow rules, but also frees the
data on currently active vlans, thus it is not restored during resume
flow.
This fix keeps the vlan data on suspend flow and frees it only on driver
remove flow.
Fixes: 6783f0a21a ("net/mlx5e: Dynamic alloc vlan table for netdev when needed")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Dan Carpenter report:
The patch f47e04eb96: "net/mlx5: E-switch, Allow setting share/max
tx rate limits of rate groups" from May 31, 2021, leads to the
following Smatch static checker warning:
drivers/net/ethernet/mellanox/mlx5/core/esw/qos.c:483 esw_qos_create_rate_group()
warn: passing zero to 'ERR_PTR'
If min rate normalization failed then error code may be overwritten to 0
if scheduling element destruction succeed. Ignore this value and always
return initial one.
Fixes: f47e04eb96 ("net/mlx5: E-switch, Allow setting share/max tx rate limits of rate groups")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Both multipath and bonding events are changing the HW LAG state
independently.
Handling one of the features events while the other is already
enabled can cause unwanted behavior, for example handling
bonding event while multipath enabled will disable the lag and
cause multipath to stop working.
Fix it by ignoring bonding event while in multipath and ignoring FIB
events while in bonding mode.
Fixes: 544fe7c2e6 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Again it became bigger than wished, unfortunately, as this contains
quite a few ASoC fixes that came up a bit late. It also includes
yet more HD- and USB-audio quirks: I decided to merge them now, as
those are for stable, and we'll need them sooner or later.
Although the volumes are a bit high, all changes are device-specific
(and reasonably small) fixes, so it should be safe for the late rc.
-----BEGIN PGP SIGNATURE-----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=zrEF
-----END PGP SIGNATURE-----
Merge tag 'sound-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Again it became bigger than wished, unfortunately, as this contains
quite a few ASoC fixes that came up a bit late. It also includes yet
more HD- and USB-audio quirks: I decided to merge them now, as those
are for stable, and we'll need them sooner or later.
Although the volumes are a bit high, all changes are device-specific
(and reasonably small) fixes, so it should be safe for the late rc"
* tag 'sound-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Fix microphone sound on Jieli webcam.
ALSA: hda/realtek: Fixes HP Spectre x360 15-eb1xxx speakers
ALSA: usb-audio: Provide quirk for Sennheiser GSP670 Headset
ALSA: hda/realtek: Add quirk for Clevo PC50HS
ALSA: usb-audio: add Schiit Hel device to quirk table
ASoC: wm8960: Fix clock configuration on slave mode
ASoC: cs42l42: Ensure 0dB full scale volume is used for headsets
ASoC: soc-core: fix null-ptr-deref in snd_soc_del_component_unlocked()
ASoC: codec: wcd938x: Add irq config support
ASoC: DAPM: Fix missing kctl change notifications
ASoC: Intel: bytcht_es8316: Utilize dev_err_probe() to avoid log saturation
ASoC: Intel: bytcht_es8316: Switch to use gpiod_get_optional()
ASoC: Intel: bytcht_es8316: Use temporary variable for struct device
ASoC: Intel: bytcht_es8316: Get platform data via dev_get_platdata()
ASoC: wcd938x: Fix jack detection issue
ASoC: nau8824: Fix headphone vs headset, button-press detection no longer working
ASoC: cs4341: Add SPI device ID table
ASoC: pcm179x: Add missing entries SPI to device ID table
ASoC: fsl_xcvr: Fix channel swap issue with ARC
ASoC: pcm512x: Mend accesses to the I2S_1 and I2S_2 registers
-----BEGIN PGP SIGNATURE-----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=tBGu
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20211019' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fix from Paul Moore:
"One small audit patch to add a pointer NULL check"
* tag 'audit-pr-20211019' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: fix possible null-pointer dereference in audit_filter_rules
As part of support for E810 XXV devices, some device ids were
inadvertently left out. Add those missing ids.
Fixes: 195fb97766 ("ice: add additional E810 device id")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
The device ID for I226_K was incorrectly assigned, update the device
ID to the correct one.
Fixes: bfa5e98c9d ("igc: Add new device ID")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update the HW MAC initialization flow. Do not gate DMA clock from
the modPHY block. Keeping this clock will prevent dropped packets
sent in burst mode on the Kumeran interface.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213651
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213377
Fixes: fb776f5d57 ("e1000e: Add support for Tiger Lake")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
- While cleaning up some of the tracing recursion protection logic,
I discovered a scenario that the current design would miss, and
would allow an infinite recursion. Removing an optimization trick
that opened the hole, fixes the issue and cleans up the code as well.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYW7CqRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qmVWAQDnboKAUVmB/3D/L1T9XdWEq4AzCS6W
51QpzWff0pBVkwEAuc1af2gqDZ6/N9sQjN9kGxikY6luVs3CSQ1yHkcanQw=
=1zGP
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Recursion fix for tracing.
While cleaning up some of the tracing recursion protection logic, I
discovered a scenario that the current design would miss, and would
allow an infinite recursion. Removing an optimization trick that
opened the hole fixes the issue and cleans up the code as well"
* tag 'trace-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Have all levels of checks prevent recursion
- Renamed CTL_STATUS to CTL_FSTATUS to fix a redefined warning
-----BEGIN PGP SIGNATURE-----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=D96y
-----END PGP SIGNATURE-----
Merge tag 'nios2_fixes_for_v5.15_part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux
Pull nios2 fix from Dinh Nguyen:
- Renamed CTL_STATUS to CTL_FSTATUS to fix a redefined warning
* tag 'nios2_fixes_for_v5.15_part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
NIOS2: irqflags: rename a redefined register name
* kvm_stat: do not show halt_wait_ns since it is not a cumulative statistic
x86:
* clean ups and fixes for bus lock vmexit and lazy allocation of rmaps
* two fixes for SEV-ES (one more coming as soon as I get reviews)
* fix for static_key underflow
ARM:
* Properly refcount pages used as a concatenated stage-2 PGD
* Fix missing unlock when detecting the use of MTE+VM_SHARED
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmFtuqYUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNGbAf9Ha4mlieY7lDQLk96GydPwlMofi1B
dteRaWizokT0Xk7HovPr8G1zwwE9DrqO1FuHiZrkckzf7cloaPDvncLag3D3Vakr
dWIqa7MaavSWBKDpcEIKOEo2SfIBU38xXQSEpegz2f2fhZK0Ud2xUNtGQMNrYatX
Lz6FXHRvHDmv4+9EjASoGBd0/C/NxMaumYa1VOxMt8JPyn+zho0z5rUDKDF4pg70
KAgxVZuksy15XFRTgaSaU0BqVn9uCHwZVqRFKBm+ocPXIFjhdMkgrxJ7NSYB1T+N
VFqcUBTFTjhg9e5eZnQ6GMf9FXpLzK912VhCRd0uU5PGeBwUDJTSnyu5OQ==
=GZqR
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Tools:
- kvm_stat: do not show halt_wait_ns since it is not a cumulative statistic
x86:
- clean ups and fixes for bus lock vmexit and lazy allocation of rmaps
- two fixes for SEV-ES (one more coming as soon as I get reviews)
- fix for static_key underflow
ARM:
- Properly refcount pages used as a concatenated stage-2 PGD
- Fix missing unlock when detecting the use of MTE+VM_SHARED"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SEV-ES: reduce ghcb_sa_len to 32 bits
KVM: VMX: Remove redundant handling of bus lock vmexit
KVM: kvm_stat: do not show halt_wait_ns
KVM: x86: WARN if APIC HW/SW disable static keys are non-zero on unload
Revert "KVM: x86: Open code necessary bits of kvm_lapic_set_base() at vCPU RESET"
KVM: SEV-ES: Set guest_state_protected after VMSA update
KVM: X86: fix lazy allocation of rmaps
KVM: SEV-ES: fix length of string I/O
KVM: arm64: Release mmap_lock when using VM_SHARED with MTE
KVM: arm64: Report corrupted refcount at EL2
KVM: arm64: Fix host stage-2 PGD refcount
KVM: s390: Function documentation fixes
We have the same LAN controller on different PCHs. Separate TGP board
type from SPT which will allow for specific fixes to be applied for
TGP platforms.
Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Setting cred->ucounts in cred_alloc_blank does not make sense. The
uid and user_ns are deliberately not set in cred_alloc_blank but
instead the setting is delayed until key_change_session_keyring.
So move dealing with ucounts into key_change_session_keyring as well.
Unfortunately that movement of get_ucounts adds a new failure mode to
key_change_session_keyring. I do not see anything stopping the parent
process from calling setuid and changing the relevant part of it's
cred while keyctl_session_to_parent is running making it fundamentally
necessary to call get_ucounts in key_change_session_keyring. Which
means that the new failure mode cannot be avoided.
A failure of key_change_session_keyring results in a single threaded
parent keeping it's existing credentials. Which results in the parent
process not being able to access the session keyring and whichever
keys are in the new keyring.
Further get_ucounts is only expected to fail if the number of bits in
the refernece count for the structure is too few.
Since the code has no other way to report the failure of get_ucounts
and because such failures are not expected to be common add a WARN_ONCE
to report this problem to userspace.
Between the WARN_ONCE and the parent process not having access to
the keys in the new session keyring I expect any failure of get_ucounts
will be noticed and reported and we can find another way to handle this
condition. (Possibly by just making ucounts->count an atomic_long_t).
Cc: stable@vger.kernel.org
Fixes: 905ae01c4a ("Add a reference to ucounts for each cred")
Link: https://lkml.kernel.org/r/7k0ias0uf.fsf_-_@disp2133
Tested-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: Alexey Gladkov <legion@kernel.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff88800906c618 (size 8):
comm "i2c-idt82p33931", pid 4421, jiffies 4294948083 (age 13.188s)
hex dump (first 8 bytes):
70 74 70 30 00 00 00 00 ptp0....
backtrace:
[<00000000312ed458>] __kmalloc_track_caller+0x19f/0x3a0
[<0000000079f6e2ff>] kvasprintf+0xb5/0x150
[<0000000026aae54f>] kvasprintf_const+0x60/0x190
[<00000000f323a5f7>] kobject_set_name_vargs+0x56/0x150
[<000000004e35abdd>] dev_set_name+0xc0/0x100
[<00000000f20cfe25>] ptp_clock_register+0x9f4/0xd30 [ptp]
[<000000008bb9f0de>] idt82p33_probe.cold+0x8b6/0x1561 [ptp_idt82p33]
When posix_clock_register() returns an error, the name allocated
in dev_set_name() will be leaked, the put_device() should be used
to give up the device reference, then the name will be freed in
kobject_cleanup() and other memory will be freed in ptp_clock_release().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: a33121e548 ("ptp: fix the race between the release of ptp_clock and cdev")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When utilizing End to End delay mechanism, the following error messages show up:
|root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m
|ptp4l[950.573]: selected /dev/ptp3 as PTP clock
|ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1
|ptp4l[956.879]: selected best master clock 001395.fffe.4897b4
|ptp4l[956.879]: port 1: assuming the grand master role
|ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER
|ptp4l[962.017]: port 1: received DELAY_REQ without timestamp
|ptp4l[962.273]: port 1: received DELAY_REQ without timestamp
|ptp4l[963.090]: port 1: received DELAY_REQ without timestamp
Commit f2fb6b6275 ("net: stmmac: enable timestamp snapshot for required PTP
packets in dwmac v5.10a") already addresses this problem for the dwmac
v5.10. However, same holds true for all dwmacs above version v4.10. Correct the
check accordingly. Afterwards everything works as expected.
Tested on Intel Atom(R) x6414RE Processor.
Fixes: 14f347334b ("net: stmmac: Correctly take timestamp for PTPv2")
Fixes: f2fb6b6275 ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a")
Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If something goes wrong in the remove callback, returning an error code
just results in an error message. The device still disappears.
So don't skip disabling the regulator in st95hf_remove() if resetting
the controller via spi fails. Also don't return an error code which just
results in two error messages.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guangbin Huang says:
====================
net: hns3: add some fixes for -net
This series adds some fixes for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko.
hns3.ko includes network stack and pci_driver, hclge.ko includes
HW device action, algo_ops and timer task, hnae3.ko includes some
register function.
When SRIOV is enable and hclge.ko is removed, HW device is unloaded
but VF still exists, PF will not reply VF mbx messages, and cause
errors.
This patch fix it by disable SRIOV before remove hclge.ko.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The task of VF reset is performed through the workqueue. It checks the
value of hdev->reset_pending to determine whether to exit the loop.
However, the value of hdev->reset_pending may also be assigned by
the interrupt function hclgevf_misc_irq_handle(), which may cause the
loop fail to exit and keep occupying the workqueue. This loop is not
necessary, so remove it and the workqueue will be rescheduled if the
reset needs to be retried or a new reset occurs.
Fixes: 1cc9bc6e58 ("net: hns3: split hclgevf_reset() into preparing and rebuilding part")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when there is a rx page allocation failure, it is
possible that polling may be stopped if there is no more packet
to be reveiced, which may cause queue stall problem under memory
pressure.
This patch makes sure polling is scheduled again when there is
any rx page allocation failure, and polling will try to allocate
receive buffers until it succeeds.
Now the allocation retry is added, it is unnecessary to do the rx
page allocation at the end of rx cleaning, so remove it. And reset
the unused_count to zero after calling hns3_nic_alloc_rx_buffers()
to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under
memory pressure.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx unused desc is the desc that need attatching new buffer
before refilling to hw to receive new packet, the number of
desc need attatching new buffer is calculated using next_to_use
and next_to_clean. when next_to_use == next_to_clean, currently
hns3 driver assumes that all the desc has the buffer attatched,
but 'next_to_use == next_to_clean' also means all the desc need
attatching new buffer if hw has comsumed all the desc and the
driver has not attatched any buffer to the desc yet.
This patch adds 'refill' in desc_cb to indicate whether a new
buffer has been refilled to a desc.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the max tx size supported by the hw is calculated by
using the max BD num supported by the hw. According to the hw
user manual, the max tx size is fixed value for both non-TSO and
TSO skb.
This patch updates the max tx size according to the manual.
Fixes: 8ae10cfb5089("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP
mode. In this case, this tc may occupy all the tx bandwidth if it has
huge traffic, so it violates the purpose of the user setting.
To fix this problem, limit the ets dwrr bandwidth must greater than 0.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, DWRR of tc will be initialized to a fixed value when this tc
is enabled, but it is not been reset to 0 when this tc is disabled. It
cause a problem that the DWRR of unused tc is not 0 after using tc tool
to add and delete multi-tc parameters.
For examples, after enabling 4 TCs and restoring to 1 TC by follow
tc commands:
$ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \
8@0 8@8 8@16 8@24 hw 1 mode channel
$ tc qdisc del dev eth0 root
Now there is just one TC is enabled for eth0, but the tc info querying by
debugfs is shown as follow:
$ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info
enabled tc number: 1
weight_offset: 14
TC MODE WEIGHT
0 dwrr 100
1 dwrr 100
2 dwrr 100
3 dwrr 100
4 dwrr 0
5 dwrr 0
6 dwrr 0
7 dwrr 0
This patch fixes it by resetting DWRR of tc to 0 when tc is disabled.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add configuration of interrupt type and fifo interrupt enable of TM QCN
error event if enabled, otherwise this event will not be reported when
there is error.
Fixes: d914971df0 ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With PREEMPT_COUNT=y, when a CPU is offlined and then onlined again, we
get:
BUG: scheduling while atomic: swapper/1/0/0x00000000
no locks held by swapper/1/0.
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.15.0-rc2+ #100
Call Trace:
dump_stack_lvl+0xac/0x108
__schedule_bug+0xac/0xe0
__schedule+0xcf8/0x10d0
schedule_idle+0x3c/0x70
do_idle+0x2d8/0x4a0
cpu_startup_entry+0x38/0x40
start_secondary+0x2ec/0x3a0
start_secondary_prolog+0x10/0x14
This is because powerpc's arch_cpu_idle_dead() decrements the idle task's
preempt count, for reasons explained in commit a7c2bb8279 ("powerpc:
Re-enable preemption before cpu_die()"), specifically "start_secondary()
expects a preempt_count() of 0."
However, since commit 2c669ef697 ("powerpc/preempt: Don't touch the idle
task's preempt_count during hotplug") and commit f1a0a376ca ("sched/core:
Initialize the idle task with preemption disabled"), that justification no
longer holds.
The idle task isn't supposed to re-enable preemption, so remove the
vestigial preempt_enable() from the CPU offline path.
Tested with pseries and powernv in qemu, and pseries on PowerVM.
Fixes: 2c669ef697 ("powerpc/preempt: Don't touch the idle task's preempt_count during hotplug")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015173902.2278118-1-nathanl@linux.ibm.com
In isa206_idle_insn_mayloss() we store various registers into the stack
red zone, which is allowed.
However inside the IDLE_STATE_ENTER_SEQ_NORET macro we save r2 again,
to 0(r1), which corrupts the stack back chain.
We used to do the same in isa206_idle_insn_mayloss() itself, but we
fixed that in 73287caa92 ("powerpc64/idle: Fix SP offsets when saving
GPRs"), however we missed that the macro also corrupts the back chain.
Corrupting the back chain is bad for debuggability but doesn't
necessarily cause a bug.
However we recently changed the stack handling in some KVM code, and it
now relies on the stack back chain being valid when it returns. The
corruption causes that code to return with r1 pointing somewhere in
kernel data, at some point LR is restored from the stack and we branch
to NULL or somewhere else invalid.
Only affects Power8 hosts running KVM guests, with dynamic_mt_modes
enabled (which it is by default).
The fixes tag below points to the commit that changed the KVM stack
handling, exposing this bug. The actual corruption of the back chain has
always existed since 948cf67c47 ("powerpc: Add NAP mode support on
Power7 in HV mode").
Fixes: 9b4416c509 ("KVM: PPC: Book3S HV: Fix stack handling in idle_kvm_start_guest()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211020094826.3222052-1-mpe@ellerman.id.au
This reverts commit 09e856d54b.
When an interface is enslaved in a VRF, prerouting conntrack hook is
called twice: once in the context of the original input interface, and
once in the context of the VRF interface. If no special precausions are
taken, this leads to creation of two conntrack entries instead of one,
and breaks SNAT.
Commit above was intended to avoid creation of extra conntrack entries
when input interface is enslaved in a VRF. It did so by resetting
conntrack related data associated with the skb when it enters VRF context.
However it breaks netfilter operation. Imagine a use case when conntrack
zone must be assigned based on the original input interface, rather than
VRF interface (that would make original interfaces indistinguishable). One
could create netfilter rules similar to these:
chain rawprerouting {
type filter hook prerouting priority raw;
iif realiface1 ct zone set 1 return
iif realiface2 ct zone set 2 return
}
This works before the mentioned commit, but not after: zone assignment
is "forgotten", and any subsequent NAT or filtering that is dependent
on the conntrack zone does not work.
Here is a reproducer script that demonstrates the difference in behaviour.
==========
#!/bin/sh
# This script demonstrates unexpected change of nftables behaviour
# caused by commit 09e856d54b ""vrf: Reset skb conntrack
# connection on VRF rcv"
# https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1
#
# Before the commit, it was possible to assign conntrack zone to a
# packet (or mark it for `notracking`) in the prerouting chanin, raw
# priority, based on the `iif` (interface from which the packet
# arrived).
# After the change, # if the interface is enslaved in a VRF, such
# assignment is lost. Instead, assignment based on the `iif` matching
# the VRF master interface is honored. Thus it is impossible to
# distinguish packets based on the original interface.
#
# This script demonstrates this change of behaviour: conntrack zone 1
# or 2 is assigned depending on the match with the original interface
# or the vrf master interface. It can be observed that conntrack entry
# appears in different zone in the kernel versions before and after
# the commit.
IPIN=172.30.30.1
IPOUT=172.30.30.2
PFXL=30
ip li sh vein >/dev/null 2>&1 && ip li del vein
ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf
nft list table testct >/dev/null 2>&1 && nft delete table testct
ip li add vein type veth peer veout
ip li add tvrf type vrf table 9876
ip li set veout master tvrf
ip li set vein up
ip li set veout up
ip li set tvrf up
/sbin/sysctl -w net.ipv4.conf.veout.accept_local=1
/sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0
ip addr add $IPIN/$PFXL dev vein
ip addr add $IPOUT/$PFXL dev veout
nft -f - <<__END__
table testct {
chain rawpre {
type filter hook prerouting priority raw;
iif { veout, tvrf } meta nftrace set 1
iif veout ct zone set 1 return
iif tvrf ct zone set 2 return
notrack
}
chain rawout {
type filter hook output priority raw;
notrack
}
}
__END__
uname -rv
conntrack -F
ping -W 1 -c 1 -I vein $IPOUT
conntrack -L
Signed-off-by: Eugene Crosser <crosser@average.org>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of leaking the ucounts in new if alloc_ucounts fails, store
the result of alloc_ucounts into a temporary variable, which is later
assigned to new->ucounts.
Cc: stable@vger.kernel.org
Fixes: 905ae01c4a ("Add a reference to ucounts for each cred")
Link: https://lkml.kernel.org/r/87pms2s0v8.fsf_-_@disp2133
Tested-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: Alexey Gladkov <legion@kernel.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The purpose of inc_rlimit_ucounts and dec_rlimit_ucounts in commit_creds
is to change which rlimit counter is used to track a process when the
credentials changes.
Use the same test for both to guarantee the tracking is correct.
Cc: stable@vger.kernel.org
Fixes: 21d1c5e386 ("Reimplement RLIMIT_NPROC on top of ucounts")
Link: https://lkml.kernel.org/r/87v91us0w4.fsf_-_@disp2133
Tested-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: Alexey Gladkov <legion@kernel.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Merge misc fixes from Andrew Morton:
"19 patches.
Subsystems affected by this patch series: mm (userfaultfd, migration,
memblock, mempolicy, slub, secretmem, and thp), ocfs2, binfmt, vfs,
and misc"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mailmap: add Andrej Shadura
mm/thp: decrease nr_thps in file's mapping on THP split
mm/secretmem: fix NULL page->mapping dereference in page_is_secretmem()
vfs: check fd has read access in kernel_read_file_from_fd()
elfcore: correct reference to CONFIG_UML
mm, slub: fix incorrect memcg slab count for bulk free
mm, slub: fix potential use-after-free in slab_debugfs_fops
mm, slub: fix potential memoryleak in kmem_cache_open()
mm, slub: fix mismatch between reconstructed freelist depth and cnt
mm, slub: fix two bugs in slab_debug_trace_open()
mm/mempolicy: do not allow illegal MPOL_F_NUMA_BALANCING | MPOL_LOCAL in mbind()
memblock: check memory total_size
ocfs2: mount fails with buffer overflow in strlen
ocfs2: fix data corruption after conversion from inline format
mm/migrate: fix CPUHP state to update node demotion order
mm/migrate: add CPU hotplug to demotion #ifdef
mm/migrate: optimize hotplug-time demotion order updates
userfaultfd: fix a race between writeprotect and exit_mmap()
mm/userfaultfd: selftests: fix memory corruption with thp enabled
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmFub7gTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqf6yCACAiYQuk1sRh7/b6G4Qk2QUTWUxhG/T
NWAOVuYMJkvGAMRAxjA7ecwRqA19/WIS2ys00t8UW62mvFGrGfcSBXWj3baPnx7w
rfhyd+gk1LqOjWcaQriDmLO2ERY27roNA7FMtcMCoRlbYkrnYcFyKUMdhQXSW3/R
/5KIEWBFzmr6ISUBUpkOeDs3irjy3ScIE0fEBt1+Uu3XydFWt7qnrMqBGlwoc9Xs
du5VN5nWTZzdB9ju7p0PyrYdwoHsa1L1XbnIJd1hTLCua38028nuL9v7OGy3QvwN
1Tz10PTnTk+2KMCkR4AwuzEBcHBVIcNmTrpTQAKiecB0QbXQlR9es0J5
=9TSz
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.15-20211019' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2021-10-19
this is a pull request of a single patch for net/master.
The patch is by me and fixes the error handling in case of a FC
timeout in the TX path of the ISOTOP CAN protocol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we check the wb_err too early for directories, before all of
the unsafe child requests have been waited on. In order to fix that we
need to check the mapping->wb_err later nearer to the end of ceph_fsync.
We also have an overly-complex method for tracking errors after
blocklisting. The errors recorded in cleanup_session_requests go to a
completely separate field in the inode, but we end up reporting them the
same way we would for any other error (in fsync).
There's no real benefit to tracking these errors in two different
places, since the only reporting mechanism for them is in fsync, and
we'd need to advance them both every time.
Given that, we can just remove i_meta_err, and convert the places that
used it to instead just use mapping->wb_err instead. That also fixes
the original problem by ensuring that we do a check_and_advance of the
wb_err at the end of the fsync op.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/52864
Reported-by: Patrick Donnelly <pdonnell@redhat.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Currently when mounting, we may end up finding an existing superblock
that corresponds to a blocklisted MDS client. This means that the new
mount ends up being unusable.
If we've found an existing superblock with a client that is already
blocklisted, and the client is not configured to recover on its own,
fail the match. Ditto if the superblock has been forcibly unmounted.
While we're in here, also rename "other" to the more conventional "fsc".
Cc: stable@vger.kernel.org
URL: https://bugzilla.redhat.com/show_bug.cgi?id=1901499
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
When the a large chunk of data send and the receiver does not send a
Flow Control frame back in time, the sendmsg() does not return a error
code, but the number of bytes sent corresponding to the size of the
packet.
If a timeout occurs the isotp_tx_timer_handler() is fired, sets
sk->sk_err and calls the sk->sk_error_report() function. It was
wrongly expected that the error would be propagated to user space in
every case. For isotp_sendmsg() blocking on wait_event_interruptible()
this is not the case.
This patch fixes the problem by checking if sk->sk_err is set and
returning the error to user space.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://github.com/hartkopp/can-isotp/issues/42
Link: https://github.com/hartkopp/can-isotp/pull/43
Link: https://lore.kernel.org/all/20210507091839.1366379-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Reported-by: Sottas Guillaume (LMB) <Guillaume.Sottas@liebherr.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a mapping for my old work email for BelDisplayTech to the personal
email, and make sure the Collabora email has the correct spelling of the
first name.
Link: https://lkml.kernel.org/r/20210917091016.30232-1-andrew.shadura@collabora.co.uk
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Decrease nr_thps counter in file's mapping to ensure that the page cache
won't be dropped excessively on file write access if page has been
already split.
I've tried a test scenario running a big binary, kernel remaps it with
THPs, then force a THP split with /sys/kernel/debug/split_huge_pages.
During any further open of that binary with O_RDWR or O_WRITEONLY kernel
drops page cache for it, because of non-zero thps counter.
Link: https://lkml.kernel.org/r/20211012120237.2600-1-m.szyprowski@samsung.com
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 09d91cda0e ("mm,thp: avoid writes to file with THP in pagecache")
Fixes: 06d3eff62d ("mm/thp: fix node page state in split_huge_page_to_list()")
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: <sfoon.kim@samsung.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: William Kucharski <william.kucharski@oracle.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we open a file without read access and then pass the fd to a syscall
whose implementation calls kernel_read_file_from_fd(), we get a warning
from __kernel_read():
if (WARN_ON_ONCE(!(file->f_mode & FMODE_READ)))
This currently affects both finit_module() and kexec_file_load(), but it
could affect other syscalls in the future.
Link: https://lkml.kernel.org/r/20211007220110.600005-1-willy@infradead.org
Fixes: b844f0ecbc ("vfs: define kernel_copy_file_from_fd()")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reported-by: Hao Sun <sunhao.th@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Mimi Zohar <zohar@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 6e7b64b9dd ("elfcore: fix building with clang") introduces
special handling for two architectures, ia64 and User Mode Linux.
However, the wrong name, i.e., CONFIG_UM, for the intended Kconfig
symbol for User-Mode Linux was used.
Although the directory for User Mode Linux is ./arch/um; the Kconfig
symbol for this architecture is called CONFIG_UML.
Luckily, ./scripts/checkkconfigsymbols.py warns on non-existing configs:
UM
Referencing files: include/linux/elfcore.h
Similar symbols: UML, NUMA
Correct the name of the config to the intended one.
[akpm@linux-foundation.org: fix um/x86_64, per Catalin]
Link: https://lkml.kernel.org/r/20211006181119.2851441-1-catalin.marinas@arm.com
Link: https://lkml.kernel.org/r/YV6pejGzLy5ppEpt@arm.com
Link: https://lkml.kernel.org/r/20211006082209.417-1-lukas.bulwahn@gmail.com
Fixes: 6e7b64b9dd ("elfcore: fix building with clang")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Barret Rhoden <brho@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When sysfs_slab_add failed, we shouldn't call debugfs_slab_add() for s
because s will be freed soon. And slab_debugfs_fops will use s later
leading to a use-after-free.
Link: https://lkml.kernel.org/r/20210916123920.48704-5-linmiaohe@huawei.com
Fixes: 64dd68497b ("mm: slub: move sysfs slab alloc/free interfaces to debugfs")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Faiyaz Mohammed <faiyazm@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In error path, the random_seq of slub cache might be leaked. Fix this
by using __kmem_cache_release() to release all the relevant resources.
Link: https://lkml.kernel.org/r/20210916123920.48704-4-linmiaohe@huawei.com
Fixes: 210e7a43fa ("mm: SLUB freelist randomization")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Faiyaz Mohammed <faiyazm@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If object's reuse is delayed, it will be excluded from the reconstructed
freelist. But we forgot to adjust the cnt accordingly. So there will
be a mismatch between reconstructed freelist depth and cnt. This will
lead to free_debug_processing() complaining about freelist count or a
incorrect slub inuse count.
Link: https://lkml.kernel.org/r/20210916123920.48704-3-linmiaohe@huawei.com
Fixes: c3895391df ("kasan, slub: fix handling of kasan_slab_free hook")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Faiyaz Mohammed <faiyazm@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "Fixups for slub".
This series contains various bug fixes for slub. We fix memoryleak,
use-afer-free, NULL pointer dereferencing and so on in slub. More
details can be found in the respective changelogs.
This patch (of 5):
It's possible that __seq_open_private() will return NULL. So we should
check it before using lest dereferencing NULL pointer. And in error
paths, we forgot to release private buffer via seq_release_private().
Memory will leak in these paths.
Link: https://lkml.kernel.org/r/20210916123920.48704-1-linmiaohe@huawei.com
Link: https://lkml.kernel.org/r/20210916123920.48704-2-linmiaohe@huawei.com
Fixes: 64dd68497b ("mm: slub: move sysfs slab alloc/free interfaces to debugfs")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Faiyaz Mohammed <faiyazm@codeaurora.org>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
