The WM8994_MICBIAS register is not available in the WM1811 CODEC so skip
initialization of that register for that device.
This suppresses an error during boot:
"wm8994-codec: ASoC: error at snd_soc_component_update_bits on wm8994-codec"
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200827173357.31891-1-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes the analogue circuitry connected to the microphone needs some
time to settle after power up. Allow systems to configure this delay in
the platform data, the driver will then insert the required delay during
power up of paths that involve the microphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than invalidating the cached DCS value every time the headphone
gain changes store multiple values, indexed by gain. This allows the
optimisation we get from the cache to take effect more often.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the analogue portions of the checks for class W are the same over
all the devices factor out these checks into wm_hubs and while we're at
it also use wm_hubs_dac_hp_direct() to enable class W optimisations on
more paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The optimisations which we can do with caching the headphone DCS result in
wm_hubs have only been enabled in cases where class W is enabled. However,
there are more use cases which can benefit from the cache, especially with
WM8994 series devices with their more advanced digital routing.
Rather than keying off the class W information from the CODECs have a
check in wm_hubs for a suitable path and use that to determine if we can
deploy our headphone optimisations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811 DC servo is able to run much faster than previous devices so
the benefit of skipping calibration is not useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The enable of the single ended line outputs on wm_hubs devices performs
better if the output is enabled prior to starting VMID. Since inactive
outputs are held at VMID anyway there is little cost to doing this for
unused outputs. Add callbacks into wm_hubs and keep track of which outputs
are really active so we can disable them once we're active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices can have performance optimized by setting different offsets
for left and right channels.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The individual devices should set the flag dcs_done_irq in the hubs
shared data structure to indicate that they will flag the interrupt
by calling wm_hubs_dcs_done().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices do not support manual updates of the DC servo.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Providing the analogue configuration of the output path remains the same
the DC offset corrected by the DC servo will remain identical so we can
skip the callibration, reducing the startup time for the headphone output.
Implement this for the wm_hubs devices as has been done for several other
CODECs.
Don't do this if we have any analogue paths enabled since offsets may be
being introduced by the analogue paths which could vary outside the
control of the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
More recent Wolfson hubs devices add the ability to read back the DC
servo calibration information from the register used to write offsets,
and later still ones remove the old readback registers. Add support
for the new scheme, and use it for WM8994 device revisions that
support it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Perform DC servo offset calibration using a series update sequence
rather than startup update sequence, tuning the configuration of the
WM8993 DC servo to make best use of this.
Also introduce currently unused data allowing us to correct for
any systematic errors in the DC servo calibration results and an
alternative startup path for the headphone output which performs
better with some chip revisions. The alternative setup sequence is
enabled for WM8993.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8993 analogue control is shared with other devices in the same
product line. Since this is a very substantial proportion of the
driver move the definitions of these controls into a new wm_hubs module
which allows them to be shared between the two.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
