A relatively large batch of fixes here but all device specific, plus an
update to MAINTAINERS. The summary print change to the STM32 driver is
fixing an issue where the driver could easily end up spamming the logs
with something that should be a debug message.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmNuPWkACgkQJNaLcl1U
h9BZJQf/Rj3kjTdwjccp+QXTrXQZVMjkXYUuLHbUokO2Mzy+U3mNCkJuvLJjAvSw
kqFBbJNYIm1jItRoqOkwlnNb0hw+QZAzBivi4DLPZJUwEeT6LxQdlYvepy6bEjCW
XJpTMFxDDaWkFUftl+tLZFN2VxHaVHEVTJ5aMu2ija0mjG1M5vrYtgVemyJ+v2/o
0nhXgnRe7Fq2+MqJazVzYs6ZxCvpIiU18a4WLD5BPGTIZhdfE0UXG+QGqWV4toHI
uZWnV+NWEKNzMGS/QdcHZYQHWlcQBR/g5kPFQFCl2D+aK9CmakHc6Bk99H6tRdLn
xYHjHafs6BwCG3eBfE/hxD8rsfTNmw==
=UfdB
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A relatively large batch of fixes here but all device specific, plus
an update to MAINTAINERS.
The summary print change to the STM32 driver is fixing an issue where
the driver could easily end up spamming the logs with something that
should be a debug message"
* tag 'spi-fix-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: amd: Fix SPI_SPD7 value
spi: stm32: fix stm32_spi_prepare_mbr() that halves spi clk for every run
spi: meson-spicc: fix do_div build error on non-arm64
spi: intel: Use correct mask for flash and protected regions
spi: mediatek: Fix package division error
spi: tegra210-quad: Don't initialise DMA if not supported
MAINTAINERS: Update HiSilicon SFC Driver maintainer
spi: meson-spicc: move wait completion in driver to take bursts delay in account
spi: stm32: Print summary 'callbacks suppressed' message
A DEVAPC violation occurs when removing the module
due to accessing HW registers without base clock.
To fix this bug, the correct method is:
1. Call the runtime resume function to enable the
clock;
2. Operate the registers to reset the HW;
3. Turn off the clocks and disable the device
RPM mechanism.
Signed-off-by: Zhichao Liu <zhichao.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110072839.30961-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When this driver is used with a driver that uses preallocated spi_transfer
structs. The speed_hz is halved by every run. This results in:
spi_stm32 44004000.spi: SPI transfer setup failed
ads7846 spi0.0: SPI transfer failed: -22
Example when running with DIV_ROUND_UP():
- First run; speed_hz = 1000000, spi->clk_rate 125000000
div 125 -> mbrdiv = 7, cur_speed = 976562
- Second run; speed_hz = 976562
div 128,00007 (roundup to 129) -> mbrdiv = 8, cur_speed = 488281
- Third run; speed_hz = 488281
div 256,000131072067109 (roundup to 257) and then -EINVAL is returned.
Use DIV_ROUND_CLOSEST to allow to round down and allow us to keep the
set speed.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20221103080043.3033414-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the const array ls1028a_soc_attr on the stack, instead
make it static. Also makes the object code smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20221102152904.143423-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes :
error: passing argument 1 of '__div64_32' from incompatible pointer type
By passing an uint64_t as first variable to do_div().
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 04694e5002 ("spi: meson-spicc: move wait completion in driver to take bursts delay in account")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221027-b4-spicc-burst-delay-fix-v2-0-8cc2bab3417a@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For using modern names host/target to instead of all the legacy names,
I think it takes 3 steps:
- step1: introduce new helpers with modern naming.
- step2: switch to use these new helpers in all drivers.
- step3: remove all legacy helpers and update all legacy names.
This patch is for step1, it introduces new helpers with host/target
naming for drivers using.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221011092204.950288-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221029071720.3041094-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221029071529.3019626-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 7e963fb2a3 ("spi: mediatek: add ipm design support
for MT7986") makes a mistake on package dividing operation
(one change is missing), need to fix it.
Background:
Ipm design is expanding the HW capability of dma (adjust package
length from 1KB to 64KB), and using "dev_comp->ipm_support" flag
to indicate it.
Issue description:
Ipm support patch (said above) is missing to handle remainder at
package dividing operation.
One case, a transmission length is 65KB, is will divide to 1K
(package length) * 65(package loop) in non-ipm desgin case, and
will divide to 64K(package length) * 1(package loop) + 1K(remainder)
in ipm design case. And the 1K remainder will be lost with the
current SW flow, and the transmission will be failure.
So, it should be fixed.
Solution:
Add "ipm_design" flag in function "mtk_spi_get_mult_delta()" to
indicate HW capability, and modify the parameters corespondingly.
fixes: 7e963fb2a3 ("spi: mediatek: add ipm design support for MT7986")
Signed-off-by: zhichao.liu <zhichao.liu@mediatek.com>
Link: https://lore.kernel.org/r/20221021091653.18297-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The following error messages are observed on boot for Tegra234 ...
ERR KERN tegra-qspi 3270000.spi: cannot use DMA: -19
ERR KERN tegra-qspi 3270000.spi: falling back to PIO
Tegra234 does not support DMA for the QSPI and so initialising the DMA
is expected to fail. The above error messages are misleading for devices
that don't support DMA and so fix this by skipping the DMA
initialisation for devices that don't support DMA.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221026155633.141792-1-jonathanh@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A collection of mostly unremarkable fixes for SPI that have built up
since the merge window, all driver specific.
The change to the qup adding support for GPIO chip selects is fixing a
regression due to the removal of legacy GPIO handling, the driver had
previously been silently relying on the legacy GPIO support in a
slightly broken way which worked well enough on some systems. Fixing
it is simply a case of setting a couple of bits of information in the
driver description.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmNZkaEACgkQJNaLcl1U
h9DKzAf+KmSNUIZ8rdfTTSvYj1SEuKd5O0YGLtRZsGLO6jhSNJ1EISCjw+9NHnoA
U/AKnnTBdexb+T5623prQL9ZU0U+JmMciHn2c34eDkvQcpdbD0ZbbqzcqxkUnPQ/
Ci5W0/9jlv7NupBSR6HXLJxjkuAVWNNUZPdy4Pb89kZIB4m/E/geRU+t/ZZgpvuf
v92AnRc0FtKlTFs2jrzScfV/R4+cygnoUoe2tJeDHYiN6ixJDJYZcU1yOcrE9544
+ovu166ZMRR6FuZ4Vd6Gso/befdaswUAwwWGghzg5IoWhIzvCkIHgtp78dk7oL29
xGgoq3lSjfzskvwNnHOWDB4tyQY7wg==
=Ni1v
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of mostly unremarkable fixes for SPI that have built up
since the merge window, all driver specific.
The change to the qup adding support for GPIO chip selects is fixing a
regression due to the removal of legacy GPIO handling, the driver had
previously been silently relying on the legacy GPIO support in a
slightly broken way which worked well enough on some systems. Fixing
it is simply a case of setting a couple of bits of information in the
driver description"
* tag 'spi-fix-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: aspeed: Fix window offset of CE1
spi: qup: support using GPIO as chip select line
spi: intel: Fix the offset to get the 64K erase opcode
spi: aspeed: Fix typo in mode_bits field for AST2600 platform
spi: mpc52xx: Replace NO_IRQ by 0
spi: spi-mem: Fix typo (of -> or)
spi: spi-gxp: fix typo in SPDX identifier line
spi: tegra210-quad: Fix combined sequence
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221026122951.331638-1-bigeasy@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Some delay occurs between each bursts, thus the default delay is wrong
and a timeout will occur with big enough transfers.
The solution is to handle the timeout management in the driver and
add some delay for each bursts in the timeout calculation.
Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221026-spicc-burst-delay-v1-0-1be5ffb7051a@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
Currently the SPI PXA2xx devices on Intel platforms can be instantiated
via the following paths:
1) as ACPI LPSS device on Haswell, Bay Trail and Cherry Trail;
2) as ACPI LPSS device on the Sky Lake and newer;
3) as PCI LPSS device on Haswell, Bay Trail and Cherry Trail;
4) as PCI LPSS device on the Sky Lake and newer;
5) as PCI device via ID table.
Each of these cases provides some platform related data differently,
i.e.:
1) via drivers/acpi/acpi_lpss.c and drivers/spi/spi-pxa2xx.c
2) via drivers/mfd/intel-lpss-acpi.c
3) via drivers/spi/spi-pxa2xx-pci.c
4) via drivers/mfd/intel-lpss-pci.c and drivers/spi/spi-pxa2xx.c
5) via drivers/spi/spi-pxa2xx-pci.c
This approach has two downsides:
a) there is no data propagated in the case #2 because we can't have
two or more drivers to match the same ACPI ID and hence some cases
are still not supported (Sky Lake and newer ACPI enabled LPSS);
b) the data is duplicated over two drivers in the cases #1 & #4 and,
besides to be a bloatware, it is error prone (e.g. Lakefield has
a wrong data right now due to missed PCI entry in the spi-pxa2xx.c).
This series fixes the downsides, and enables previously unsupported
cases.
There is no code that uses ID tables directly, except the
struct device_driver at the end of the file. Hence, move
tables closer to its user. It's always possible to access
them via pointer to a platform device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20221021190018.63646-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the PCI enumerated devices provide a property with SSP type,
there is no more necessity to bear the copy of the ID table here.
Remove it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221021190018.63646-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow to set the Intel SSP type by reading the property.
Only apply this to the known MFD enumerated LPSS devices.
The check is done by the looking for the specifically
named IO memory resource provided by upper layer. This
won't be an issue in the future because we strictly
prioritize the order in which we are looking for the SSP
type in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221021190018.63646-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we blindly apply the SSP type value from any source of the
information. Increase robustness by validating the value before use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221021190018.63646-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_{get_and_}ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221019092635.1176622-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The original fix "spi: stm32: Rate-limit the 'Communication suspended' message"
still leads to "stm32h7_spi_irq_thread: 1696 callbacks suppressed" spew in the
kernel log. Since this 'Communication suspended' message is a debug print, add
RATELIMIT_MSG_ON_RELEASE flag to inhibit the "callbacks suspended" part during
normal operation and only print summary at the end.
Fixes: ea8be08cc9 ("spi: stm32: Rate-limit the 'Communication suspended' message")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221018183513.206706-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Amjad Ouled-Ameur <aouledameur@baylibre.com>:
Between SPI transactions, all SPI pins are in HiZ state. When using the SS
signal from the SPICC controller it's not an issue because when the
transaction resumes all pins come back to the right state at the same time
as SS.
The problem is when we use CS as a GPIO. In fact, between the GPIO CS
state change and SPI pins state change from idle, you can have a missing or
spurious clock transition.
Set a bias on the clock depending on the clock polarity requested before CS
goes active, by passing a special "idle-low" and "idle-high" pinctrl state
and setting the right state at a start of a message.
Between SPI transactions, all SPI pins are in HiZ state. When using the SS
signal from the SPICC controller it's not an issue because when the
transaction resumes all pins come back to the right state at the same time
as SS.
The problem is when we use CS as a GPIO. In fact, between the GPIO CS
state change and SPI pins state change from idle, you can have a missing or
spurious clock transition.
Set a bias on the clock depending on the clock polarity requested before CS
goes active, by passing a special "idle-low" and "idle-high" pinctrl state
and setting the right state at a start of a message
Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Link: https://lore.kernel.org/r/20221004-up-aml-fix-spi-v4-2-0342d8e10c49@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 7a908832ac ("spi: imx: add fallback feature") the last
user of the struct spi_imx_devtype_data::disable_dma callback was
removed. However the disable_dma member of struct spi_imx_devtype_data
and the callback itself was not removed.
Remove struct spi_imx_devtype_data::disable_dma and mx51_disable_dma()
as they are unused.
Cc: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20221021131051.1777984-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Cleaning up the driver to use pm_ptr() macro instead of ifdeffery
that makes it simpler and allows the compiler to remove those functions
if built without CONFIG_PM and CONFIG_PM_SLEEP support.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20221020194500.10225-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The proposed spi_get_device_match_data() helper is for retrieving
a driver data associated with the ID in an ID table. First, it tries
to get driver data of the device enumerated by firmware interface
(usually Device Tree or ACPI). If none is found it falls back to
the SPI ID table matching.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221020195421.10482-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:
A bunch of improvements to the driver:
- Fix kernel-doc warnings in GQSPI driver.
- Avoid setting CPOL, CPHA & baud rate multiple times.
- Add Versal platform support in GQSPI driver.
- Add tap delay support in GQSPI driver.
Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221019093318.1183190-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset value of the mapping window in the kernel structure is
calculated using the value of the previous window offset. This doesn't
reflect how the HW is configured and can lead to erroneous setting of
the second flash device (CE1).
Cc: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Fixes: e3228ed928 ("spi: spi-mem: Convert Aspeed SMC driver to spi-mem")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20221016155722.3520802-1-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add tap delay support for GQSPI controller on Versal platform.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-8-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
GQSPI controller uses the internal clock for loopback mode. The loopback
mode is used with the high-speed Quad SPI timing mode, where the memory
interface clock needs to be greater than 40 MHz. Based on the tap delay
value programmed, the internal clock is delayed and used for capturing
the data.
Based upon the frequency of operation set the recommended tap delay
values in GQSPI driver.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-6-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During every transfer the GQSPI driver configures the baud rate value. But
when there is no change in the SPI clock frequency the driver should avoid
rewriting the same baud rate value to the configuration register. Update
GQSPI driver to rewrite the baud rate value if there is any change in SPI
clock frequency.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-4-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During every transfer GQSPI driver writes the CPOL & CPHA values to the
configuration register. But the CPOL & CPHA values do not change in between
multiple transfers, so moved the CPOL & CPHA initialization to hardware
init so that the values are written only once.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-3-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Document zynqmp_qspi ctrl and op_lock member description. It also adds
return documentation for 'zynqmp_qspi_setuprxdma' and zynqmp_qspi_read_op.
Fixes below kernel-doc warnings-
spi-zynqmp-gqspi.c:178: warning: Function parameter or member 'ctlr' not
described in 'zynqmp_qspi'
spi-zynqmp-gqspi.c:178: warning: Function parameter or member 'op_lock'
not described in 'zynqmp_qspi'
spi-zynqmp-gqspi.c:737: warning: No description found for return value of
'zynqmp_qspi_setuprxdma'
spi-zynqmp-gqspi.c:822: warning: No description found for return value of
'zynqmp_qspi_read_op'
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-2-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Not all zero page implementations use empty_zero_page global pointer so
let's substitute empty_zero_page occurence with helper ZERO_PAGE(0).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Link: https://lore.kernel.org/r/20221018215755.33566-2-giulio.benetti@benettiengineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function bcm_qspi_remove() returns zero unconditionally. Make it
return void.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221017200143.1426528-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
No functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221017171243.57078-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_{get_and}_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220928145852.1882221-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220928145852.1882221-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Microchip pci1xxxx is a PCIe switch with a multi-function endpoint on one of its
downstream ports. SPI is one of the functions in the multi-function endpoint. This
function has 2 SPI masters, operates at a maximum frequency of 30 MHz and supports
7 client devices per master. This patch adds complete functionality to the SPI
function except for suspend and resume.
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Link: https://lore.kernel.org/r/20221006050514.115564-2-tharunkumar.pasumarthi@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function mchp_corespi_enable() is defined in the spi-microchip-core.c
file, but not called elsewhere, so delete this unused function.
drivers/spi/spi-microchip-core.c:122:20: warning: unused function 'mchp_corespi_enable'.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2418
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221017092141.9789-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of the device with QUP SPI adapter are actually using GPIO-s for
chip select.
However, this stopped working after ("spi: Retire legacy GPIO handling")
as it introduced a check on ->use_gpio_descriptors flag and since spi-qup
driver does not set the flag it meant that all of boards using GPIO-s and
with QUP adapter SPI devices stopped working.
So, to enable using GPIO-s again set ->use_gpio_descriptors to true and
populate ->max_native_cs.
Fixes: f48dc6b966 ("spi: Retire legacy GPIO handling")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: luka.perkov@sartura.hr
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221006194819.1536932-1-robert.marko@sartura.hr
Signed-off-by: Mark Brown <broonie@kernel.org>
According to documentation, the 64K erase opcode is located in VSCC
range [16:23] instead of [8:15].
Use the proper value to shift the mask over the correct range.
Signed-off-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221012152135.28353-1-mauro.lima@eclypsium.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both quad SPI TX and RX modes can be supported on AST2600.
Correct typo in mode_bits field in both ast2600_fmc_data
and ast2600_spi_data structs.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20221005083209.222272-1-chin-ting_kuo@aspeedtech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
NO_IRQ is used to check the return of irq_of_parse_and_map().
On some architecture NO_IRQ is 0, on other architectures it is -1.
irq_of_parse_and_map() returns 0 on error, independent of NO_IRQ.
So use 0 instead of using NO_IRQ.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f41e09d710879726eacb98daedf16d0847303b9b.1665034444.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
With the exception of some refactoring to fix long standing issues
where we weren't handling cache syncs properly for messages which had
PIO and DMA transfers going to the same page correctly there has been o
work on the core this time around, and it's also been quite a quiet
release for the drivers too:
- Fix cache syncs for cases where we have DMA and PIO transfers in the
same message going to the same page.
- Update the fsl_spi driver to use transfer_one() rather than a custom
transfer function.
- Support for configuring transfer speeds with the AMD SPI controller.
- Support for a second chip select and 64K erase on Intel SPI.
- Support for Microchip coreQSPI, Nuvoton NPCM845, NXP i.MX93, and
Rockchip RK3128 and RK3588.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmM62YIACgkQJNaLcl1U
h9CvPAf+MF1AzJJWH9DkR846KQh7Zt1rrujRuj5SGwvHewqjJcDtDmipAbM7mRFa
VPk6fCzfRE4btVywCDMEQX2ToB9VKBNUeP8ihVLddWrTddbkQ7hOKlTrz31dJ+6W
F9kwXkWcqWEpMYD/wr/25eT/kkNfv27oCyPU4dRQKoGGeF+zb9jYoj0+gPDl9Om8
ok7D1XAwY1wOqYqdPfl2thcUrBfoKtFvkTj+NNhqwuzWwIqfQHM2skwAjmD3fliQ
lLdRc54erCOqukDddIoWr348TyJIT4v1IXnkqY3cd7da6+kpixWae73o/7WIcQUR
4MrtPply0WWcapgU/46sCbHpjJNjjg==
=PDCv
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"With the exception of some refactoring to fix long standing issues
where we weren't handling cache syncs properly for messages which had
PIO and DMA transfers going to the same page correctly there has been
no work on the core this time around, and it's also been quite a quiet
release for the drivers too:
- Fix cache syncs for cases where we have DMA and PIO transfers in
the same message going to the same page
- Update the fsl_spi driver to use transfer_one() rather than a
custom transfer function
- Support for configuring transfer speeds with the AMD SPI controller
- Support for a second chip select and 64K erase on Intel SPI
- Support for Microchip coreQSPI, Nuvoton NPCM845, NXP i.MX93, and
Rockchip RK3128 and RK3588"
* tag 'spi-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (73 commits)
spi: Ensure that sg_table won't be used after being freed
spi: spi-gxp: Use devm_platform_ioremap_resource()
spi: s3c64xx: Fix large transfers with DMA
spi: Split transfers larger than max size
spi: Fix cache corruption due to DMA/PIO overlap
spi: Save current RX and TX DMA devices
spi: mt65xx: Add dma max segment size declaration
spi: migrate mt7621 text bindings to YAML
spi: renesas,sh-msiof: Add r8a779g0 support
spi: spi-fsl-qspi: Use devm_platform_ioremap_resource_byname()
spi: spi-fsl-lpspi: Use devm_platform_get_and_ioremap_resource()
spi: spi-fsl-dspi: Use devm_platform_get_and_ioremap_resource()
spi/omap100k:Fix PM disable depth imbalance in omap1_spi100k_probe
spi: dw: Fix PM disable depth imbalance in dw_spi_bt1_probe
spi: cadence-quadspi: Fix PM disable depth imbalance in cqspi_probe
spi: s3c24xx: Switch to use devm_spi_alloc_master()
spi: xilinx: Switch to use devm_spi_alloc_master()
spi: img-spfi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
spi: aspeed: Remove redundant dev_err call
spi: spi-mpc52xx: switch to using gpiod API
...
Merge ACPI _UID handling unification changes for 6.1-rc1:
- Introduce acpi_dev_uid_to_integer() to convert a _UID string into an
integer value (Andy Shevchenko).
- Use acpi_dev_uid_to_integer() in several places to unify _UID
handling (Andy Shevchenko).
* acpi-uid:
efi/dev-path-parser: Refactor _UID handling to use acpi_dev_uid_to_integer()
spi: pxa2xx: Refactor _UID handling to use acpi_dev_uid_to_integer()
perf: qcom_l2_pmu: Refactor _UID handling to use acpi_dev_uid_to_integer()
i2c: mlxbf: Refactor _UID handling to use acpi_dev_uid_to_integer()
i2c: amd-mp2-plat: Refactor _UID handling to use acpi_dev_uid_to_integer()
ACPI: x86: Refactor _UID handling to use acpi_dev_uid_to_integer()
ACPI: LPSS: Refactor _UID handling to use acpi_dev_uid_to_integer()
ACPI: utils: Add acpi_dev_uid_to_integer() helper to get _UID as integer
Return value should be updated to zero in combined sequence routine
if transfer is completed successfully. Currently it holds timeout value
resulting in errors.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/20221001122148.9158-1-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge changes regarding the management of ACPI device objects for
6.1-rc1:
- Rename ACPI device object reference counting functions (Rafael
Wysocki).
- Rearrange ACPI device object initialization code (Rafael Wysocki).
- Drop parent field from struct acpi_device (Rafael Wysocki).
- Extend the the int3472-tps68470 driver to support multiple consumers
of a single TPS68470 along with the requisite framework-level
support (Daniel Scally).
* acpi-dev:
platform/x86: int3472: Add board data for Surface Go2 IR camera
platform/x86: int3472: Support multiple gpio lookups in board data
platform/x86: int3472: Support multiple clock consumers
ACPI: bus: Add iterator for dependent devices
ACPI: scan: Add acpi_dev_get_next_consumer_dev()
ACPI: property: Use acpi_dev_parent()
ACPI: Drop redundant acpi_dev_parent() header
ACPI: PM: Fix NULL argument handling in acpi_device_get/set_power()
ACPI: Drop parent field from struct acpi_device
ACPI: scan: Eliminate __acpi_device_add()
ACPI: scan: Rearrange initialization of ACPI device objects
ACPI: scan: Rename acpi_bus_get_parent() and rearrange it
ACPI: Rename acpi_bus_get/put_acpi_device()
SPI code checks for non-zero sgt->orig_nents to determine if the buffer
has been DMA-mapped. Ensure that sg_table is really zeroed after free to
avoid potential NULL pointer dereference if the given SPI xfer object is
reused again without being DMA-mapped.
Fixes: 0c17ba73c0 ("spi: Fix cache corruption due to DMA/PIO overlap")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220930113408.19720-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220928145256.1879256-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The COUNT_VALUE in the PACKET_CNT register is 16-bit so the maximum
value is 65535. Asking the driver to transfer a larger size currently
leads to the DMA transfer timing out. Implement ->max_transfer_size()
and have the core split the transfer as needed.
Fixes: 230d42d422 ("spi: Add s3c64xx SPI Controller driver")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-5-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of drivers call spi_split_transfers_maxsize() from their
->prepare_message() callbacks to split transfers which are too big for
them to handle. Add support in the core to do this based on
->max_transfer_size() to avoid code duplication.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-4-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core DMA mapping support performs cache management once for the
entire message and not between transfers, and this leads to cache
corruption if a message has two or more RX transfers with both
transfers targeting the same cache line, and the controller driver
decides to handle one using DMA and the other using PIO (for example,
because one is much larger than the other).
Fix it by syncing before/after the actual transfers. This also means
that we can skip the sync during the map/unmap of the message.
Fixes: 99adef310f ("spi: Provide core support for DMA mapping transfers")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-3-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Save the current RX and TX DMA devices to avoid having to duplicate the
logic to pick them, since we'll need access to them in some more
functions to fix a bug in the cache handling.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-2-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi dma max segment size declaration according to spi
hardware capability, instead of 64KB by system default
setting, to improve bus bandwidth for mass data transmission.
Signed-off-by: zhichao.liu <zhichao.liu@mediatek.com>
Link: https://lore.kernel.org/r/20220927083248.25404-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Zhang Qilong <zhangqilong3@huawei.com>:
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed when error returns to keep it
balanced. This series of patches fixed it in spi probe.
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220924131854.964923-3-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220924131854.964923-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220924131854.964923-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:db91841b58f9a ("spi/omap100k: Convert to runtime PM")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-4-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:abf00907538e2 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-3-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:73d5fe0462702 ("spi: cadence-quadspi: Remove spi_master_put() in probe failure path")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-2-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to use devm_spi_alloc_master() to simpify error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220920142216.3002291-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_ioremap_resource() prints error message in itself. Remove the
dev_err call to avoid redundant error message.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220923101632.19170-1-shangxiaojing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This switches the driver to use gpiod API instead of legacy gpio API,
which will brings us close to removing of_get_gpio() and other
OF-specific old APIs.
No functional change intended beyond some differences in error messages.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/Yy07WbMAG4bPgYNd@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_ioremap_resource() prints error message in itself. Remove the
dev_err call to avoid redundant error message.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Link: https://lore.kernel.org/r/20220923101726.19420-1-shangxiaojing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to use devm_spi_alloc_master() to simpify error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20220920114448.2681053-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The sparse tool complains as follows:
drivers/spi/spi-meson-spicc.c:570:22: warning:
symbol 'meson_spicc_pow2_clk_ops' was not declared. Should it be static?
This symbol is not used outside of spi-meson-spicc.c, so marks it static.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220922040807.1409540-1-weiyongjun@huaweicloud.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This condition was accidentally changed from "if (status < 0)" to
"if (status)". The platform_get_irq() function returns non-zero
positive values on success so, unfortunately, the driver could not be
used. Change the condition back to how it was.
Fixes: f4ca8c88c2 ("spi: omap2-mcspi: Switch to use dev_err_probe() helper")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/Yyq8Q/kd301wVzg8@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
ACPI utils provide acpi_dev_uid_to_integer() helper to extract _UID as
an integer. Use it instead of custom approach.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a test where a small and a large transfer in a message hit the same
cache line. This test currently fails on spi-s3c64xx on in DMA mode
since it ends up mixing DMA and PIO without proper cache maintenance.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220916113951.228398-2-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the probe path, dev_err() can be replace with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220917122504.1896302-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Let the core handle all the chipselect bakery and replace
transfer_one_message() by transfer_one() and prepare_message().
At the time being, there is fsl_spi_cs_control() to handle
chipselects. That function handles both GPIO and non-GPIO
chipselects. The GPIO chipselects will now be handled by
the core directly, so only handle non-GPIO chipselects and
hook it to ->set_cs
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/753266abafe81722d86c3ddb8bac8ef1cb00fe8c.1660829841.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Several fixes that came in since the merge window, the major one being a
fix for the spi-mux driver which was broken by the performance
optimisations due to it peering inside the core's data structures more
than it should.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmMZ22MACgkQJNaLcl1U
h9BV9Af/fvJZTo35a2NBZ6kUw/V+73LSxfEfzfzjqfXhYTTiYshDTvRi7MK+FdrU
E84vuidJkmP1+NVRbyoiBbDhx9Ejq11tHL8rpCm/0PTrSd3jc2WMs9ODGG0XIXst
j3Q7WnaWOfvvETSDVw8jNs8B9zdMMXsluaTJUIn1hjQWSVYTt67hsqtwRjrRlwmI
xLjVcYygnsiggNetAKCqmamPG9W94v6aUlhQ7c7aiAqYwQgy94sCBye+T4pV64rK
mF28RkdDx6U9TA08uSepmwgUC9PEWyCIsVSoJs0DuKXZH9WQ/ixsFDubC8WodIKT
/IgtX+Xpf6bES6n8fi3tidd7HkXrqw==
=ZJei
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"Several fixes that came in since the merge window, the major one being
a fix for the spi-mux driver which was broken by the performance
optimisations due to it peering inside the core's data structures more
than it should"
* tag 'spi-fix-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi: Fix queue hang if previous transfer failed
spi: mux: Fix mux interaction with fast path optimisations
spi: cadence-quadspi: Disable irqs during indirect reads
spi: bitbang: Fix lsb-first Rx
Since [1], controller's busy flag isn't set anymore when the
__spi_transfer_message_noqueue() is used instead of the
__spi_pump_transfer_message() logic for spi_sync transfers.
Since the pow2 clock ops were limited to only be available when a
transfer is ongoing (between prepare_transfer_hardware and
unprepare_transfer_hardware callbacks), the only way to track this
down is to check for the controller cur_msg.
[1] ae7d2346dc ("spi: Don't use the message queue if possible in spi_sync")
Fixes: 09992025da ("spi: meson-spicc: add local pow2 clock ops to preserve rate between messages")
Fixes: ae7d2346dc ("spi: Don't use the message queue if possible in spi_sync")
Reported-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/r/20220908121803.919943-1-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Return the value pm_runtime_force_suspend() directly instead of storing
it in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220908010429.342875-1-ye.xingchen@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Some components require a few clock cycles with chipselect off before
or/and after the data transfer done with CS on.
Typically IDT 801034 QUAD PCM CODEC datasheet states "Note *: CCLK
should have one cycle before CS goes low, and two cycles after
CS goes high".
The cycles "before" are implicitely provided by all previous activity
on the SPI bus. But the cycles "after" must be provided in order to
terminate the SPI transfer.
In order to use that kind of component, add a cs_off flag to
spi_transfer struct. When this flag is set, the transfer is performed
with chipselect off. This allows consummer to add a dummy transfer
at the end of the transfer list which is performed with chipselect
OFF, providing the required additional clock cycles.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/434165c46f06d802690208a11e7ea2500e8da4c7.1662558898.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to make the underneath API easier to change in the future,
prevent users from dereferencing fwnode from struct device. Instead,
use the specific dev_fwnode() API for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220906161048.39953-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing clk_disable_unprepare() before return
from spi_qup_pm_resume_runtime() in the error handling case.
Fixes: dae1a7700b (“spi: qup: Handle clocks in pm_runtime suspend and resume”)
Signed-off-by: Xu Qiang <xuqiang36@huawei.com>
Link: https://lore.kernel.org/r/20220825065324.68446-2-xuqiang36@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing clk_disable_unprepare() before return
from spi_qup_resume() in the error handling case.
Fixes: 64ff247a97 (“spi: Add Qualcomm QUP SPI controller support”)
Signed-off-by: Xu Qiang <xuqiang36@huawei.com>
Link: https://lore.kernel.org/r/20220825065324.68446-1-xuqiang36@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The queue worker always needs to be kicked one final time after a transfer
is done in order to transition to idle (ctlr->busy = false).
Commit 69fa95905d ("spi: Ensure the io_mutex is held until
spi_finalize_current_message()") moved this code into
__spi_pump_messages(), but it was executed only if the transfer was
successful. This condition check causes ctlr-busy to stay true in case of
a failed transfer.
This in turn causes that no new work is ever scheduled to the work queue.
Fixes: 69fa95905d ("spi: Ensure the io_mutex is held until spi_finalize_current_message()")
Reported-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220901123630.1098433-1-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-mux driver is rather too clever and attempts to resubmit any
message that is submitted to it to the parent controller with some
adjusted callbacks. This does not play at all nicely with the fast
path which now sets flags on the message indicating that it's being
handled through the fast path, we see async messages flagged as being on
the fast path. Ideally the spi-mux code would duplicate the message but
that's rather invasive and a bit fragile in that it relies on the mux
knowing which fields in the message to copy. Instead teach the core
that there are controllers which can't cope with the fast path and have
the mux flag itself as being such a controller, ensuring that messages
going via the mux don't get partially handled via the fast path.
This will reduce the performance of any spi-mux connected device since
we'll now always use the thread for both the actual controller and the
mux controller instead of just the actual controller but given that we
were always hitting the slow path anyway it's hopefully not too much of
an additional cost and it allows us to keep the fast path.
Fixes: ae7d2346dc ("spi: Don't use the message queue if possible in spi_sync")
Reported-by: Casper Andersson <casper.casan@gmail.com>
Tested-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220901120732.49245-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
gpiod_count() either returns positive number of the CS or negative
error code. In the stm32_qspi_setup() we check that configuration
has enough CS for the dual flash mode and SPI mode is not changing
over the lines of the code. Taking all above into considertion,
refactor dual flash mode enable check by dropping unneeded CS check
and reusing local mode variable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220830182821.47919-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparation to unexport of_gpio_named_count(), convert the
driver to use gpiod_count() instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220830182821.47919-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the current speed is equal to the requested speed by the device
then return success.
This patch fixes a bug introduced by the commit 3fe26121dc
("spi: amd: Configure device speed") which checks speed_hz instead
of amd_spi->speed_hz.
Fixes: 3fe26121dc ("spi: amd: Configure device speed")
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Link: https://lore.kernel.org/r/20220830093607.45484-1-shreeya.patel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Christophe JAILLET <christophe.jaillet@wanadoo.fr>:
Patch 1 fixes an issue about an error code that is erroneously logged.
Patch 2-4 are just clean-ups spotted while fixing it.
Additional comments are added below --- in patches 2 and 3.
Now that clk_disable_unprepare(clk) is handled with a managed resource,
we can use devm_spi_register_controller() and axe the .remove function.
The order between spi_unregister_controller() and clk_disable_unprepare()
is still the same.
(see commit 46b5c4fb87 ("spi: mt7621: Don't leak SPI master in probe
error path") to see why it matters)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/b7698e198acc998d99e7e7c895a2910f14f89443.1661599671.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This helper is well suited for cases where the clock would be kept
prepared or enabled for the whole lifetime of the driver.
This simplifies the error handling a lot.
The order between spi_unregister_controller() (in the remove function) and
the clk_disable_unprepare() (now handle by a managed resource) is kept
the same.
(see commit 46b5c4fb87 ("spi: mt7621: Don't leak SPI master in probe
error path") to see why it matters)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/05a7fd22719008c8a905d6328aa9548ce40f2a7a.1661599671.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
'status' is known to be 0 at this point. The expected error code is
PTR_ERR(clk).
Switch to dev_err_probe() in order to display the expected error code (in a
human readable way).
This also filters -EPROBE_DEFER cases, should it happen.
Fixes: 1ab7f2a435 ("staging: mt7621-spi: add mt7621 support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/928f3fb507d53ba0774df27cea0bbba4b055993b.1661599671.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Wolfram Sang <wsa+renesas@sang-engineering.com>:
Here are the patches to enable MSIOF on R-Car S4-8. They also introduce
generic Gen4 support and move V3U to Gen4 (which it really is).
ctrl->auto_runtime_pm was wrongly set to true when adding
transfer_one_message() callback.
As explained in commit 6e6ccb3d4cdc ("spi: stm32-qspi: Add pm_runtime support")
the expected behavior is to prevent runtime suspends between each transfer.
Add needed pm_runtime API calls in stm32_qspi_transfer_one_message().
Fixes: a557fca630 ("spi: stm32_qspi: Add transfer_one_message() spi callback")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220829123250.2170562-1-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch a557fca630: "spi: stm32_qspi: Add transfer_one_message()
spi callback" from Aug 23, 2022, leads to the following Smatch static
checker warning:
drivers/spi/spi-stm32-qspi.c:627 stm32_qspi_transfer_one_message()
error: uninitialized symbol 'ret'.Fix the following Smatch static checker warning:
Fixes: a557fca630 ("spi: stm32_qspi: Add transfer_one_message() spi callback")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220826092031.1393430-1-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Number of clock frequencies are supported by AMD controller
which are mentioned in the amd_spi_freq structure table.
Create mechanism to configure device clock frequency such
that it is strictly less than the requested frequency.
Give priority to the device transfer speed and in case
it is not set then use the max clock speed supported
by the device.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Co-developed-by: Shreeya Patel <shreeya.patel@collabora.com>
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Link: https://lore.kernel.org/r/20220825143132.253224-1-shreeya.patel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Return the value clk_prepare_enable() directly instead of storing it in
another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220825072828.229294-1-ye.xingchen@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The parent field in struct acpi_device is, in fact, redundant,
because the dev.parent field in it effectively points to the same
object and it is used by the driver core.
Accordingly, the parent field can be dropped from struct acpi_device
and for this purpose define acpi_dev_parent() to retrieve a parent
struct acpi_device pointer from the dev.parent field in struct
acpi_device. Next, update all of the users of the parent field
in struct acpi_device to use acpi_dev_parent() instead of it and
drop it.
While at it, drop the ACPI_IS_ROOT_DEVICE() macro that is only used
in one place in a confusing way.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Reviewed-by: Punit Agrawal <punit.agrawal@bytedance.com>
Merge series from patrice.chotard@foss.st.com <patrice.chotard@foss.st.com>:
The goal of this series is to allow to use QSPI bus as a 8 lines communication
channel for specific purpose.
The QSPI block offers the possibility to communicate with 2 flashes in
parrallel using the dual flash mode, 8 data lines are then used.
Usage of cs-gpios populated and spi-tx-bus-width / spi-rx-bus-width both set to 8,
is needed to enable dual flash mode.
The addition of the legacy transfer_one_message() spi callback is also needed
as currently the stm32-qspi driver only supports spi_controller_mem_ops API.
It's pretty possible to have the spi_register_controller() method
returning -EPROBE_DEFER status in case, for instance, if the GPIOs used
for the CS implementation aren't ready to be requested due to the
corresponding platform devices still pending to be probed. Let's make sure
the DW SSI driver won't print error message in that case by calling the
dev_err_probe() function if the SPI-registration procedure exited with
a non-zero status.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220822181853.23063-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Add transfer_one_message() spi callback in order to use the QSPI interface
as a communication channel using up to 8 qspi lines (QSPI configured
in dual flash mode).
To enable this mode, both spi-rx-bus-width and spi-tx-bus-width must be
set to 8 and cs-qpios must be populated.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220823075850.575043-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The hardware sequencer in Intel Canon Lake and beyond supports also 64k
erase command. The SPI-NOR core uses SFDP (Serial Flash Discovery
Parameter) to figure out what the chip actually supports and only issues
64k erase if it is supported.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220816125537.89389-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel SPI flash controller has been supporting two chip selects long
time already even if the most common configuration is to have a single
flash chip for the BIOS and related data. This adds support for the
second chip select if we find out that there are two flash components
(this information is available in the mandatory flash descriptor on the
first chip). The second chip is exposed as is without any partition
information.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220816130818.89600-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On architecture where reading the SRAM is slower than the pace at
controller fills it, with interrupt enabled while reading from
SRAM FIFO causes unwanted interrupt storm to CPU.
The inner "bytes to read" loop never exits and waits for the completion
so it is enough to only enable the watermark interrupt when we
are out of bytes to read, which only happens when we start the
transfer (waiting for the FIFO to fill up initially) if the SRAM
is slow.
So only using read watermark interrupt, as the current implementation
doesn't utilize the SRAM full and indirect complete read interrupt.
And disable all the read interrupts while reading from SRAM.
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Link: https://lore.kernel.org/r/20220813042616.1372110-1-niravkumar.l.rabara@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The AMD SPI controller hardware seems to expect the FIFO buffer to be
fully setup with the details of all transfers in the SPI message before
it is able to start processing the data in a reliable way.
Furthermore, it imposes a strict ordering restriction, in the sense that
all TX transfers must be handled prior any RX transfer.
Hence, let's ensure amd_spi_execute_opcode() is called only once, after
all TX transfers have been setup, and process any remaining RX transfers
afterwards, in a second iteration.
Additionally, get rid of the unnecessary AMD_SPI_XFER_TX/RX defines and
improve error handling.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20220818010059.403776-1-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A few fixes that came in since my pull request, the Meson fix is a
little large since it's fixing all possible cases of the problem that
was observed with the driver and clock API trying to share configuration
by integrating the device clocking fully with the clock API rather than
spot fixing the one instance that was observed.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmL7fVUACgkQJNaLcl1U
h9DNIAf/ThNZXWK1+ujLkCe3VW2CfOWSBQMtL1jW7vrRI2qNMoEj478wUMUZJ83R
Sl5X7w3PW7OmiJTvTzqngS+OkUUR/8Hcp8Cvcz1DJYmBV0iYOwPjinNfbB/Z77B7
4HaBOdBdMSCq6nFX7obKc4tyNGb6ZBD3YJ+PW+CRhUozfvGPXAUDoh5Eq4q1efh3
UJW5lP88Lp4zwd9rh8y05ugLFzXdxWV1LwICj2cj3+KceRwObwNfSs8Qp60iOrC+
QuSIiaZJA77BbG6y/i6Y/lZo/06ZcYAU0QzdUdaffNk+V7aadfvz2IlTHuoe186A
bV3xv1ucL2FJlrx4DAZtWp4b5EcPmA==
=xXEL
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few fixes that came in since my pull request, the Meson fix is a
little large since it's fixing all possible cases of the problem that
was observed with the driver and clock API trying to share
configuration by integrating the device clocking fully with the clock
API rather than spot fixing the one instance that was observed"
* tag 'spi-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dt-bindings: Drop Pratyush Yadav
spi: meson-spicc: add local pow2 clock ops to preserve rate between messages
MAINTAINERS: rectify entry for ARM/HPE GXP ARCHITECTURE
spi: spi.c: Add missing __percpu annotations in users of spi_statistics
Merge series from Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>:
This patch enables the Microchip's FPGA QSPI and Polarfire SoC QSPI
controller support.
Tested spi-nand (W25N01GV) and spi-nor (MT25QL256A) on Microchip's
ICICLE kit. tested using both FPGA QSPI and Polarfie SoC QSPI.
dev_err_probe() already prints the error code in a human readable way, so
there is no need to duplicate it as a numerical value at the end of the
message.
Fixes: 12f62a857c ("spi: lpspi: Silence error message upon deferred probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-By: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/253543c462b765eca40ba54c66f4e3fdf4acdeb7.1659735546.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_err_probe() already prints the error code in a human readable way, so
there is no need to duplicate it as a numerical value at the end of the
message.
Moreover, in the case of devm_clk_get() it would only display '0' because
'ret' is know to be 0 at this point.
Fixes: cdeaf3a99a ("spi: microchip-core: switch to use dev_err_probe()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/fb894ecec68e03fb7fc9353027c8b1a2610833d7.1659735153.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Use NULL for dma channel pointer initialization instead of plain integer.
sparse warnings: (new ones prefixed by >>)
>> drivers/spi/spi-s3c64xx.c:387:34: sparse: sparse: Using plain integer as NULL pointer
drivers/spi/spi-s3c64xx.c:388:34: sparse: sparse: Using plain integer as NULL pointer
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 82295bc0d1 ("spi: s3c64xx: move dma_release_channel to unprepare")
Fixes: f52b03c707 ("spi: s3c64xx: requests spi-dma channel only during data transfer")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220808004851.25122-1-chanho61.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a driver for Microchip FPGA QSPI controllers. This driver also
supports "hard" QSPI controllers on Polarfire SoC.
Signed-off-by: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220808064603.1174906-4-nagasuresh.relli@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shifting the recieved bit by "bits" inserts it at the top of the
*currently remaining* Tx data, so we end up accumulating the whole
transfer into bit 0 of the output word. Oops.
For the algorithm to work as intended, we need to remember where the
top of the *original* word was, and shift Rx to there.
Fixes: 1847e3046c ("spi: gpio: Implement LSB First bitbang support")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/28324d8622da80461cce35a82859b003d6f6c4b0.1659538737.git.robin.murphy@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
At the end of a message, the HW gets a reset in meson_spicc_unprepare_transfer(),
this resets the SPICC_CONREG register and notably the value set by the
Common Clock Framework.
This is problematic because:
- the register value CCF can be different from the corresponding CCF cached rate
- CCF is allowed to change the clock rate whenever the HW state
This introduces:
- local pow2 clock ops checking the HW state before allowing a clock operation
- separation of legacy pow2 clock patch and new enhanced clock path
- SPICC_CONREG datarate value is now value kepts across messages
It has been checked that:
- SPICC_CONREG datarate value is kept across messages
- CCF is only allowed to change the SPICC_CONREG datarate value when busy
- SPICC_CONREG datarate value is correct for each transfer
This didn't appear before commit 3e0cf4d3fc ("spi: meson-spicc: add a linear clock divider support")
because we recalculated and wrote the rate for each xfer.
Fixes: 3e0cf4d3fc ("spi: meson-spicc: add a linear clock divider support")
Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220811134445.678446-1-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add support for syscall stack randomization.
- Add support for atomic operations to the 32 & 64-bit BPF JIT.
- Full support for KASAN on 64-bit Book3E.
- Add a watchdog driver for the new PowerVM hypervisor watchdog.
- Add a number of new selftests for the Power10 PMU support.
- Add a driver for the PowerVM Platform KeyStore.
- Increase the NMI watchdog timeout during live partition migration, to avoid timeouts
due to increased memory access latency.
- Add support for using the 'linux,pci-domain' device tree property for PCI domain
assignment.
- Many other small features and fixes.
Thanks to: Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira Rajeev, Bagas
Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas, Greg Kroah-Hartman, Greg Kurz,
Haowen Bai, Hari Bathini, Jason A. Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg
Haefliger, Kajol Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch, Naveen N. Rao, Nayna
Jain, Nicholas Piggin, Ning Qiang, Pali Rohár, Petr Mladek, Rashmica Gupta, Sachin Sant,
Scott Cheloha, Segher Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, Zhouyi Zhou.
-----BEGIN PGP SIGNATURE-----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=tRkm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add support for syscall stack randomization
- Add support for atomic operations to the 32 & 64-bit BPF JIT
- Full support for KASAN on 64-bit Book3E
- Add a watchdog driver for the new PowerVM hypervisor watchdog
- Add a number of new selftests for the Power10 PMU support
- Add a driver for the PowerVM Platform KeyStore
- Increase the NMI watchdog timeout during live partition migration, to
avoid timeouts due to increased memory access latency
- Add support for using the 'linux,pci-domain' device tree property for
PCI domain assignment
- Many other small features and fixes
Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira
Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas,
Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A.
Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch,
Naveen N. Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár,
Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher
Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, and Zhouyi Zhou.
* tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits)
powerpc/64e: Fix kexec build error
EDAC/ppc_4xx: Include required of_irq header directly
powerpc/pci: Fix PHB numbering when using opal-phbid
powerpc/64: Init jump labels before parse_early_param()
selftests/powerpc: Avoid GCC 12 uninitialised variable warning
powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
powerpc/xive: Fix refcount leak in xive_get_max_prio
powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
powerpc/perf: Include caps feature for power10 DD1 version
powerpc: add support for syscall stack randomization
powerpc: Move system_call_exception() to syscall.c
powerpc/powernv: rename remaining rng powernv_ functions to pnv_
powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
powerpc/powernv: Avoid crashing if rng is NULL
selftests/powerpc: Fix matrix multiply assist test
powerpc/signal: Update comment for clarity
powerpc: make facility_unavailable_exception 64s
powerpc/platforms/83xx/suspend: Remove write-only global variable
powerpc/platforms/83xx/suspend: Prevent unloading the driver
powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration
...
Here is the set of driver core and kernfs changes for 6.0-rc1.
"biggest" thing in here is some scalability improvements for kernfs for
large systems. Other than that, included in here are:
- arch topology and cache info changes that have been reviewed
and discussed a lot.
- potential error path cleanup fixes
- deferred driver probe cleanups
- firmware loader cleanups and tweaks
- documentation updates
- other small things
All of these have been in the linux-next tree for a while with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYuqCnw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym/JgCcCnaycJY00ZPRQm3LQCyzfJ0HgqoAn2qxGV+K
NKycLeXZSnuvIA87dycE
=/4Jk
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / kernfs updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.0-rc1.
The "biggest" thing in here is some scalability improvements for
kernfs for large systems. Other than that, included in here are:
- arch topology and cache info changes that have been reviewed and
discussed a lot.
- potential error path cleanup fixes
- deferred driver probe cleanups
- firmware loader cleanups and tweaks
- documentation updates
- other small things
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'driver-core-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (63 commits)
docs: embargoed-hardware-issues: fix invalid AMD contact email
firmware_loader: Replace kmap() with kmap_local_page()
sysfs docs: ABI: Fix typo in comment
kobject: fix Kconfig.debug "its" grammar
kernfs: Fix typo 'the the' in comment
docs: driver-api: firmware: add driver firmware guidelines. (v3)
arch_topology: Fix cache attributes detection in the CPU hotplug path
ACPI: PPTT: Leave the table mapped for the runtime usage
cacheinfo: Use atomic allocation for percpu cache attributes
drivers/base: fix userspace break from using bin_attributes for cpumap and cpulist
MAINTAINERS: Change mentions of mpm to olivia
docs: ABI: sysfs-devices-soc: Update Lee Jones' email address
docs: ABI: sysfs-class-pwm: Update Lee Jones' email address
Documentation/process: Add embargoed HW contact for LLVM
Revert "kernfs: Change kernfs_notify_list to llist."
ACPI: Remove the unused find_acpi_cpu_cache_topology()
arch_topology: Warn that topology for nested clusters is not supported
arch_topology: Add support for parsing sockets in /cpu-map
arch_topology: Set cluster identifier in each core/thread from /cpu-map
arch_topology: Limit span of cpu_clustergroup_mask()
...
The big update this time around is some excellent work from David Jander
who went through the fast path and really eliminated overheads, meaning
that we are seeing a huge reduction in the time spent between transfers
for single threaded clients. Benchmarking has been coming out at about a
halving of overhead which is clearly visible in system level usage that
stresses SPI like some CAN and IIO applications, especially with small
transfers. Thanks to David for taking the time to drill down into this
and push the work upstream.
Otherwise there's been a bunch of new device support and the usual
- Optimisation of the fast path, particularly around the number and
types of locking operations, from David Jander.
- Support for Arbel NPCM845, HP GXP, Intel Meteor Lake and Thunder Bay,
MediaTek MT8188 and MT8365, Microchip FPGAs, nVidia Tegra 241 and
Samsung Exynos Auto v9 and 4210.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmLnyFYACgkQJNaLcl1U
h9AVpAf7BJI8NBQ659fyvfZkJDTlH8F3IjH4P3WpxMPCmTqvCZ5wBZyxwMIXGySE
fe7iQw3PGXBcoEHxhYPR4ePp7LO5jHePybUzGCJBD0EYhlo9QVBpD5+P4t65c9z8
Hjpul428My4L7eUGl/29iv0Qzkyd3wnVPSsZqBCB6BOPTQ+hribs93Uj6rB4wmzF
9Vu4p+dqdGvdrIj3G2KpFRtKxhpnjUeD5l8Eq3rOPlEPjSKoHADHP2ZSpxoz5jfR
8L6C+RyADs7ro7X4hiIq1TGURVJ+6EkGDdc6O+Rj0S+PL7MCVOGR0ucPZMOVmNbJ
114wnOQNmVnGKHX0IBm7VIOMkfc7Dg==
=5frj
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The big update this time around is some excellent work from David
Jander who went through the fast path and really eliminated overheads,
meaning that we are seeing a huge reduction in the time spent between
transfers for single threaded clients.
Benchmarking has been coming out at about a halving of overhead which
is clearly visible in system level usage that stresses SPI like some
CAN and IIO applications, especially with small transfers. Thanks to
David for taking the time to drill down into this and push the work
upstream.
Otherwise there's been a bunch of new device support and the usual
updates.
- Optimisation of the fast path, particularly around the number and
types of locking operations, from David Jander.
- Support for Arbel NPCM845, HP GXP, Intel Meteor Lake and Thunder
Bay, MediaTek MT8188 and MT8365, Microchip FPGAs, nVidia Tegra 241
and Samsung Exynos Auto v9 and 4210"
* tag 'spi-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (97 commits)
MAINTAINERS: add spi support to GXP
spi: dt-bindings: add documentation for hpe,gxp-spifi
spi: spi-gxp: Add support for HPE GXP SoCs
spi: a3700: support BE for AC5 SPI driver
spi/panel: dt-bindings: drop CPHA and CPOL from common properties
spi: bcm2835: enable shared interrupt support
spi: dt-bindings: spi-controller: correct example indentation
spi: dt-bindings: qcom,spi-geni-qcom: allow three interconnects
spi: npcm-fiu: Add NPCM8XX support
dt-binding: spi: Add npcm845 compatible to npcm-fiu document
spi: npcm-fiu: Modify direct read dummy configuration
spi: atmel: remove #ifdef CONFIG_{PM, SLEEP}
spi: dt-bindings: Add compatible for MediaTek MT8188
spi: dt-bindings: mediatek,spi-mtk-nor: Update bindings for nor flash
spi: dt-bindings: atmel,at91rm9200-spi: convert to json-schema
spi: tegra20-slink: fix UAF in tegra_slink_remove()
spi: Fix simplification of devm_spi_register_controller
spi: microchip-core: switch to use dev_err_probe()
spi: microchip-core: switch to use devm_spi_alloc_master()
spi: microchip-core: fix UAF in mchp_corespi_remove()
...
The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management
to allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and
use the firmware interfaces for system power control and for
power capping.
-----BEGIN PGP SIGNATURE-----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=0dZI
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC drivers from Arnd Bergmann:
"The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management to
allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and use
the firmware interfaces for system power control and for power
capping"
* tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (125 commits)
soc: a64fx-diag: disable modular build
dt-bindings: soc: qcom: qcom,smd-rpm: add power-controller
dt-bindings: soc: qcom: aoss: document qcom,sm8450-aoss-qmp
dt-bindings: soc: qcom,rpmh-rsc: simplify qcom,tcs-config
ARM: mach-qcom: Add support for MSM8909
dt-bindings: arm: cpus: Document "qcom,msm8909-smp" enable-method
soc: qcom: spm: Add CPU data for MSM8909
dt-bindings: soc: qcom: spm: Add MSM8909 CPU compatible
soc: qcom: rpmpd: Add compatible for MSM8909
dt-bindings: power: qcom-rpmpd: Add MSM8909 power domains
soc: qcom: smd-rpm: Add compatible for MSM8909
dt-bindings: soc: qcom: smd-rpm: Add MSM8909
soc: qcom: icc-bwmon: Remove unnecessary print function dev_err()
soc: fujitsu: Add A64FX diagnostic interrupt driver
soc: qcom: socinfo: Fix the id of SA8540P SoC
soc: qcom: Make QCOM_RPMPD depend on PM
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
...
Merge series from nick.hawkins@hpe.com <nick.hawkins@hpe.com>:
The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash and bios part.
The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash and bios part.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Link: https://lore.kernel.org/r/20220728161459.7738-2-nick.hawkins@hpe.com
Signed-off-by: Mark Brown <broonie@kernel.org>
BCM2711 shares an interrupt betweem 5 SPI interfaces (0, 3, 4, 5 & 6).
Another interrupt is shared between SPI1, SPI2 and UART1, which also
affects BCM2835/6/7. Acting on an interrupt intended for another
interface ought to be harmless (although potentially inefficient), but
it can cause this driver to crash - presumably because some critical
state is not ready.
Add a test to the spi-bcm2835 interrupt service routine that
interrupts are enabled on this interface to avoid the crash and
improve efficiency.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://github.com/raspberrypi/linux/issues/5048
Suggested-by: https://github.com/boe-pi
Co-developed-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220719105305.3076354-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
RSPI IP on RZ/{A, G2L} SoC's has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked.
PIO fallback does not work as interrupt signal is disabled.
This patch fixes this issue by re-enabling the interrupts by
calling dmaengine_synchronize().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220721143449.879257-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix SPI NO Slave Select macro definition, when all the SPI CS bits
are high which means no slave is selected.
Fixes: 21b511ddee ("spi: spi-cadence: Fix SPI CS gets toggling sporadically")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220713164529.28444-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding FIU NPCM8XX support to NPCM FIU driver.
NPCM8XX FIU supports four controllers.
As part of adding NPCM8XX support:
- Add NPCM8XX specific compatible string.
- Using an internal burst configuration register instead of a GCR
register.
- Support FIU1 controller.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20220718081146.256070-4-tmaimon77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case a IRQ based transfer times out the bcm2835_spi_handle_err()
function is called. Since commit 1513ceee70 ("spi: bcm2835: Drop
dma_pending flag") the TX and RX DMA transfers are unconditionally
canceled, leading to NULL pointer derefs if ctlr->dma_tx or
ctlr->dma_rx are not set.
Fix the NULL pointer deref by checking that ctlr->dma_tx and
ctlr->dma_rx are valid pointers before accessing them.
Fixes: 1513ceee70 ("spi: bcm2835: Drop dma_pending flag")
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220719072234.2782764-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove #ifdef CONFIG_PM, #ifdef CONFIG_PM_SLEEP and use
SYSTEM_SLEEP_PM_OPS() and RUNTIME_PM_OPS() macros instead which allows
getting also rid of __maybe_unused in the code.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220718071052.1707858-1-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the spi_master is allocated by devm_spi_alloc_master()
and devres core manages the deallocation, but in probe failure
path spi_master_put() is being handled manually which causes
"refcount underflow use-after-free" warning when probe failure happens
after allocating spi_master.
Trimmed backtrace during failure:
refcount_t: underflow; use-after-free.
pc : refcount_warn_saturate+0xf4/0x144
Call trace:
refcount_warn_saturate
kobject_put
put_device
devm_spi_release_controller
devres_release_all
This commit makes relevant changes to remove spi_master_put() from probe
failure path.
Fixes: 606e5d4081 ("spi: cadence-quadspi: Handle spi_unregister_master() in remove()")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220601071611.11853-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from nandhini.srikandan@intel.com <nandhini.srikandan@intel.com>:
This patch enables support for DW SPI on Intel Thunder Bay. This patch
set also enables master mode for latest Designware SPI versions. The
driver is tested on Keem Bay and Thunder Bay evaluation board.
Merge series from Yang Yingliang <yangyingliang@huawei.com>:
Patch #1 fix a UAF in mchp_corespi_remove().
Patch #2 and #3 some cleanups to simpify code.
After calling spi_unregister_master(), the refcount of master will
be decrease to 0, and it will be freed in spi_controller_release(),
the device data also will be freed, so it will lead a UAF when using
'tspi'. To fix this, get the master before unregister and put it when
finish using it.
Fixes: 26c8634182 ("spi: tegra20-slink: Don't use resource-managed spi_register helper")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220713094024.1508869-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 59ebbe40fb ("spi: simplify
devm_spi_register_controller").
If devm_add_action() fails in devm_add_action_or_reset(),
devm_spi_unregister() will be called, it decreases the
refcount of 'ctlr->dev' to 0, then it will cause uaf in
the drivers that calling spi_put_controller() in error path.
Fixes: 59ebbe40fb ("spi: simplify devm_spi_register_controller")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220712135504.1055688-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to use devm_spi_alloc_master() to simpify error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220713025657.3524506-3-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When using devm_spi_register_master(), the unregister function will
be called in devres_release_all() which is called after ->remove(),
so remove spi_unregister_master() andspi_master_put().
Fixes: 9ac8d17694 ("spi: add support for microchip fpga spi controllers")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220713025657.3524506-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Intel Thunder Bay SPI controller, which uses DesignWare
DWC_ssi core and also add common init function for both Keem Bay and
Thunder Bay.
Signed-off-by: Nandhini Srikandan <nandhini.srikandan@intel.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20220713042223.1458-5-nandhini.srikandan@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
