This patch reorders and realigns the tg3_napi members for a ~3-4%
performance improvement on small packet performance tests.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under load, there an internal FIFO can overflow on the 5719. The fix is
to scale back the PCIe maximum read request size based on the current
link speed and width.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The APE needs certain bits in the mac_mode register to be enabled for
traffic to flow correctly. This patch changes the code to always enable
these bits in the presence of the APE.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d309a46e42, entitled
"tg3: 5719: Prevent tx data corruption", was supposed to contain the tx
margin adjustment but it looks like it somehow was omitted. This patch
fixes the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a977dbe844, entitled
"tg3: Reduce 57765 core clock when link at 10Mbps" needs to be applied
to all revisions of the 57765 asic rev, not just the A0 revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix unbalanced call to sdio_release_host() on the error path.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SELinux ip postroute code indicates when policy rejected a packet and
passes the error back up the stack. The compat code does not. This patch
sends the same kind of error back up the stack in the compat code.
Based-on-patch-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Reviewed-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the SELinux netlink code returns a fatal error when the error might
actually be transient. This patch just silently drops packets on
potentially transient errors but continues to return a permanant error
indicator when the denial was because of policy.
Based-on-comments-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Reviewed-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wireless-testing commit a05b5d4504
ath9k: add support for reading eeprom from platform data on PCI devices
This change moved the initialization of the AH_USE_EEPROM flag from ath9k_hw
to ath9k. This needs to be added to ath9k_htc as well
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under load, a large number of frames can produce decryption errors, even when
no key cache update is being done. Performing a key search for every single
frame in an A-MPDU improves reliability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark arrays const that are unmodified after initializations.
text data bss dec hex filename
19291 56 4136 23483 5bbb drivers/net/wireless/zd1211rw/zd_chip.o.old
19291 56 4136 23483 5bbb drivers/net/wireless/zd1211rw/zd_chip.o.new
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
40197 56 8336 48589 bdcd drivers/net/wireless/rt2x00/rt2800lib.o.new
40205 56 8336 48597 bdd5 drivers/net/wireless/rt2x00/rt2800lib.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
41757 2205 9896 53858 d262 drivers/net/wireless/rndis_wlan.o.old
41653 2205 9880 53738 d1ea drivers/net/wireless/rndis_wlan.o.new
Changed functions rndis_set_oid and set_bssid to take const *'s.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
42607 3581 8536 54724 d5c4 drivers/net/wireless/ray_cs.o.new
42603 3585 8536 54724 d5c4 drivers/net/wireless/ray_cs.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
3650 56 704 4410 113a drivers/net/wireless/libertas/rx.o.new
3695 56 704 4455 1167 drivers/net/wireless/libertas/rx.o.old
27328 964 5240 33532 82fc drivers/net/wireless/libertas/cfg.o.new
27328 964 5240 33532 82fc drivers/net/wireless/libertas/cfg.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
48644 57 12120 60821 ed95 drivers/net/wireless/b43/phy_n.o.new
48661 57 12120 60838 eda6 drivers/net/wireless/b43/phy_n.o.old
37906 86 7904 45896 b348 drivers/net/wireless/iwlwifi/iwl-agn-lib.o.new
37937 86 7904 45927 b367 drivers/net/wireless/iwlwifi/iwl-agn-lib.o.old
37781 523 6752 45056 b000 drivers/net/wireless/iwlwifi/iwl-3945.o.new
37781 523 6752 45056 b000 drivers/net/wireless/iwlwifi/iwl-3945.o.old
Changed b43_nphy_write_clip_detection to take a const u16 *
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
5502 56 1336 6894 1aee drivers/net/wireless/b43/phy_common.o.new
5511 56 1336 6903 1af7 drivers/net/wireless/b43/phy_common.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
42578 720 8528 51826 ca72 drivers/net/wireless/atmel.o.old
42578 720 8528 51826 ca72 drivers/net/wireless/atmel.o.new
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
1897 56 672 2625 a41 drivers/net/wireless/ath/carl9170/cmd.o.new
1897 56 672 2625 a41 drivers/net/wireless/ath/carl9170/cmd.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
11266 56 2464 13786 35da drivers/net/wireless/ath/ath5k/ani.o.old
11181 56 2464 13701 3585 drivers/net/wireless/ath/ath5k/ani.o.new
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit: "carl9170: tx path review" introduced a regression.
gcc (with -Winit-self):
tx.c:1264: warning: ‘super’ is used uninitialized in this function
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove duplicated #include('s) in
drivers/net/wireless/libertas/cfg.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If only 3945 is selected, and is a module, build
fails because iwl-legacy.c won't be compiled. Fix
this by adding it to the build correctly.
This doesn't happen for 4965 because it is a bool
option, not tristate, since it's built into the
AGN module.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using AP VLAN interfaces, each VLAN interface should be in its own
broadcast domain. Hostapd achieves this by assigning different GTKs to
different AP VLAN interfaces.
However, mac80211 drivers are not aware of AP VLAN interfaces and as
such mac80211 sends the GTK to the driver in the context of the base AP
mode interface. This causes problems when multiple AP VLAN interfaces
are used since the driver will use the same key slot for the different
GTKs (there's no way for the driver to distinguish the different GTKs
from different AP VLAN interfaces). Thus, only the clients associated
to one AP VLAN interface (the one that was created last) can actually
use broadcast traffic.
Fix this by not programming any GTKs for AP VLAN interfaces into the hw
but fall back to using software crypto. The GTK for the underlying AP
interface is still sent to the driver.
That means, broadcast traffic to stations associated to an AP VLAN
interface is encrypted in software whereas broadcast traffic to
stations associated to the non-VLAN AP interface is encrypted in
hardware.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When two cards are connected with the same regulatory domain
if CRDA had a delayed response then cfg80211's own set regulatory
domain would still be the world regulatory domain. There was a bug
on cfg80211's logic such that it assumed that once you pegged a
request as the last request it was already the currently set
regulatory domain. This would mean we would race setting a stale
regulatory domain to secondary cards which had the same regulatory
domain since the alpha2 would match.
We fix this by processing each regulatory request atomically,
and only move on to the next one once we get it fully processed.
In the case CRDA is not present we will simply world roam.
This issue is only present when you have a slow system and the
CRDA processing is delayed. Because of this it is not a known
regression.
Without this fix when a delay is present with CRDA the second card
would end up with an intersected regulatory domain and not allow it
to use the channels it really is designed for. When two cards with
two different regulatory domains were inserted you'd end up
rejecting the second card's regulatory domain request.
This fails with mac80211_hswim's regtest=2 (two requests, same alpha2)
and regtest=3 (two requests, different alpha2) module parameter
options.
This was reproduced and tested against mac80211_hwsim using this
CRDA delayer:
#!/bin/bash
echo $COUNTRY >> /tmp/log
sleep 2
/sbin/crda.orig
And these regulatory tests:
modprobe mac80211_hwsim regtest=2
modprobe mac80211_hwsim regtest=3
Reported-by: Mark Mentovai <mark@moxienet.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be required in the next patch and it makes the
next patch easier to review.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used earlier in the next few patches.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will simplify the synchronization for pending requests.
Without this we have a race between the core and when we
restore regulatory settings, although this is unlikely
its best to just avoid that race altogether.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices which use LO enabled bit are covered by b43legacy
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new vendor for Broadcom 4318.
Signed-off-by: Daniel Klaffenbach <danielklaffenbach@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that using ath9k_hw_stoppcurecv to stop rx dma is not enough.
When it's time to stop DMA, the PCU is still busy, so the rx enable
bit never clears.
Using ath9k_hw_abortpcurecv helps with getting rx stopped much faster,
with this change, I cannot reproduce the rx stop related WARN_ON anymore.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the current default 'vepa' mode, a KVM guest using virtio with
macvtap backend has the following limitations.
- cannot change/add a mac address on the guest virtio-net
- cannot create a vlan device on the guest virtio-net
- cannot enable promiscuous mode on guest virtio-net
To address these limitations, this patch introduces a new mode called
'passthru' when creating a macvlan device which allows takeover of the
underlying device and passing it to a guest using virtio with macvtap
backend.
Only one macvlan device is allowed in passthru mode and it inherits
the mac address from the underlying device and sets it in promiscuous
mode to receive and forward all the packets.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
-------------------------------------------------------------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Also, use the ccflags-$ flag instead of EXTRA_CFLAGS because EXTRA_CFLAGS is
deprecated and should now be switched.
Last but not least, took out if-conditionals.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
