After commit 939463016b ("tcp: change data receiver flowlabel after one dup")
we noticed an increase of TCPACKSkippedPAWS events.
Neal Cardwell tracked the issue to tcp_disordered_ack() assumption
about remote peer TS clock.
RFC 1323 & 7323 are suggesting the following:
"timestamp clock frequency in the range 1 ms to 1 sec per tick
between 1ms and 1sec."
This has to be adjusted for 1 MHz clock frequency.
This hints at reorders of SACK packets on send side,
this might deserve a future patch.
(skb->ooo_okay is always set for pure ACK packets)
Fixes: 614e8316aa ("tcp: add support for usec resolution in TCP TS values")
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Morley <morleyd@google.com>
Link: https://lore.kernel.org/r/20231207181342.525181-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is based on a detailed report and ideas from Yepeng Pan
and Christian Rossow.
ACK seq validation is currently following RFC 5961 5.2 guidelines:
The ACK value is considered acceptable only if
it is in the range of ((SND.UNA - MAX.SND.WND) <= SEG.ACK <=
SND.NXT). All incoming segments whose ACK value doesn't satisfy the
above condition MUST be discarded and an ACK sent back. It needs to
be noted that RFC 793 on page 72 (fifth check) says: "If the ACK is a
duplicate (SEG.ACK < SND.UNA), it can be ignored. If the ACK
acknowledges something not yet sent (SEG.ACK > SND.NXT) then send an
ACK, drop the segment, and return". The "ignored" above implies that
the processing of the incoming data segment continues, which means
the ACK value is treated as acceptable. This mitigation makes the
ACK check more stringent since any ACK < SND.UNA wouldn't be
accepted, instead only ACKs that are in the range ((SND.UNA -
MAX.SND.WND) <= SEG.ACK <= SND.NXT) get through.
This can be refined for new (and possibly spoofed) flows,
by not accepting ACK for bytes that were never sent.
This greatly improves TCP security at a little cost.
I added a Fixes: tag to make sure this patch will reach stable trees,
even if the 'blamed' patch was adhering to the RFC.
tp->bytes_acked was added in linux-4.2
Following packetdrill test (courtesy of Yepeng Pan) shows
the issue at hand:
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1024) = 0
// ---------------- Handshake ------------------- //
// when window scale is set to 14 the window size can be extended to
// 65535 * (2^14) = 1073725440. Linux would accept an ACK packet
// with ack number in (Server_ISN+1-1073725440. Server_ISN+1)
// ,though this ack number acknowledges some data never
// sent by the server.
+0 < S 0:0(0) win 65535 <mss 1400,nop,wscale 14>
+0 > S. 0:0(0) ack 1 <...>
+0 < . 1:1(0) ack 1 win 65535
+0 accept(3, ..., ...) = 4
// For the established connection, we send an ACK packet,
// the ack packet uses ack number 1 - 1073725300 + 2^32,
// where 2^32 is used to wrap around.
// Note: we used 1073725300 instead of 1073725440 to avoid possible
// edge cases.
// 1 - 1073725300 + 2^32 = 3221241997
// Oops, old kernels happily accept this packet.
+0 < . 1:1001(1000) ack 3221241997 win 65535
// After the kernel fix the following will be replaced by a challenge ACK,
// and prior malicious frame would be dropped.
+0 > . 1:1(0) ack 1001
Fixes: 354e4aa391 ("tcp: RFC 5961 5.2 Blind Data Injection Attack Mitigation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yepeng Pan <yepeng.pan@cispa.de>
Reported-by: Christian Rossow <rossow@cispa.de>
Acked-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20231205161841.2702925-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This extra check doesn't work for a handshake when SYN segment has
(current_key.maclen != rnext_key.maclen). It could be amended to
preserve rnext_key.maclen instead of current_key.maclen, but that
requires a lookup on listen socket.
Originally, this extra maclen check was introduced just because it was
cheap. Drop it and convert tcp_request_sock::maclen into boolean
tcp_request_sock::used_tcp_ao.
Fixes: 06b22ef295 ("net/tcp: Wire TCP-AO to request sockets")
Signed-off-by: Dmitry Safonov <dima@arista.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use DO_ONCE_LITE_IF() and __cold attribute to put tcp_gro_dev_warn()
out of line.
This also allows the message to be printed again after a
"echo 1 > /sys/kernel/debug/clear_warn_once"
Also add a READ_ONCE() when reading device mtu, as it could
be changed concurrently.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20231130184135.4130860-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After blamed commit, TFO client-ack-dropped-then-recovery-ms-timestamps
packetdrill test failed.
David Morley and Neal Cardwell started investigating and Neal pointed
that we had :
tcp_conn_request()
tcp_try_fastopen()
-> tcp_fastopen_create_child
-> child = inet_csk(sk)->icsk_af_ops->syn_recv_sock()
-> tcp_create_openreq_child()
-> copy req_usec_ts from req:
newtp->tcp_usec_ts = treq->req_usec_ts;
// now the new TFO server socket always does usec TS, no matter
// what the route options are...
send_synack()
-> tcp_make_synack()
// disable tcp_rsk(req)->req_usec_ts if route option is not present:
if (tcp_rsk(req)->req_usec_ts < 0)
tcp_rsk(req)->req_usec_ts = dst_tcp_usec_ts(dst);
tcp_conn_request() has the initial dst, we can initialize
tcp_rsk(req)->req_usec_ts there instead of later in send_synack();
This means tcp_rsk(req)->req_usec_ts can be a boolean.
Many thanks to David an Neal for their help.
Fixes: 614e8316aa ("tcp: add support for usec resolution in TCP TS values")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202310302216.f79d78bc-oliver.sang@intel.com
Suggested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Morley <morleyd@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to TCP-MD5, add a static key to TCP-AO that is patched out
when there are no keys on a machine and dynamically enabled with the
first setsockopt(TCP_AO) adds a key on any socket. The static key is as
well dynamically disabled later when the socket is destructed.
The lifetime of enabled static key here is the same as ao_info: it is
enabled on allocation, passed over from full socket to twsk and
destructed when ao_info is scheduled for destruction.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Sequence Number Extension (SNE) for TCP-AO.
This is needed to protect long-living TCP-AO connections from replaying
attacks after sequence number roll-over, see RFC5925 (6.2).
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when the new request socket is created from the listening socket,
it's recorded what MKT was used by the peer. tcp_rsk_used_ao() is
a new helper for checking if TCP-AO option was used to create the
request socket.
tcp_ao_copy_all_matching() will copy all keys that match the peer on the
request socket, as well as preparing them for the usage (creating
traffic keys).
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper that:
(1) shares the common code with TCP-MD5 header options parsing
(2) looks for hash signature only once for both TCP-MD5 and TCP-AO
(3) fails with -EEXIST if any TCP sign option is present twice, see
RFC5925 (2.2):
">> A single TCP segment MUST NOT have more than one TCP-AO in its
options sequence. When multiple TCP-AOs appear, TCP MUST discard
the segment."
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add traffic key calculation the way it's described in RFC5926.
Wire it up to tcp_finish_connect() and cache the new keys straight away
on already established TCP connections.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in 2015, Van Jacobson suggested to use usec resolution in TCP TS values.
This has been implemented in our private kernels.
Goals were :
1) better observability of delays in networking stacks.
2) better disambiguation of events based on TSval/ecr values.
3) building block for congestion control modules needing usec resolution.
Back then we implemented a schem based on private SYN options
to negotiate the feature.
For upstream submission, we chose to use a route attribute,
because this feature is probably going to be used in private
networks [1] [2].
ip route add 10/8 ... features tcp_usec_ts
Note that RFC 7323 recommends a
"timestamp clock frequency in the range 1 ms to 1 sec per tick.",
but also mentions
"the maximum acceptable clock frequency is one tick every 59 ns."
[1] Unfortunately RFC 7323 5.5 (Outdated Timestamps) suggests
to invalidate TS.Recent values after a flow was idle for more
than 24 days. This is the part making usec_ts a problem
for peers following this recommendation for long living
idle flows.
[2] Attempts to standardize usec ts went nowhere:
https://www.ietf.org/proceedings/97/slides/slides-97-tcpm-tcp-options-for-low-latency-00.pdfhttps://datatracker.ietf.org/doc/draft-wang-tcpm-low-latency-opt/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before adding usec TS support, add tcp_rtt_tsopt_us() helper
to factorize code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helper returns a TSval from a TCP socket.
It currently calls tcp_time_stamp_ms() but will soon
be able to return a usec based TSval, depending
on an upcoming tp->tcp_usec_ts field.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helper returns a 32bit TCP TSval from skb->tstamp.
As we are going to support usec or ms units soon, rename it
to tcp_skb_timestamp_ts() and add a boolean to select the unit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of adding usec TCP TS values, add tcp_time_stamp_ms()
for contexts needing ms based values.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fix wrong RTO timeout when received SACK reneging.
When an ACK arrived pointing to a SACK reneging, tcp_check_sack_reneging()
will rearm the RTO timer for min(1/2*srtt, 10ms) into to the future.
But since the commit 62d9f1a694 ("tcp: fix TLP timer not set when
CA_STATE changes from DISORDER to OPEN") merged, the tcp_set_xmit_timer()
is moved after tcp_fastretrans_alert()(which do the SACK reneging check),
so the RTO timeout will be overwrited by tcp_set_xmit_timer() with
icsk_rto instead of 1/2*srtt.
Here is a packetdrill script to check this bug:
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
// simulate srtt to 100ms
+0 < S 0:0(0) win 32792 <mss 1000, sackOK,nop,nop,nop,wscale 7>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 7>
+.1 < . 1:1(0) ack 1 win 1024
+0 accept(3, ..., ...) = 4
+0 write(4, ..., 10000) = 10000
+0 > P. 1:10001(10000) ack 1
// inject sack
+.1 < . 1:1(0) ack 1 win 257 <sack 1001:10001,nop,nop>
+0 > . 1:1001(1000) ack 1
// inject sack reneging
+.1 < . 1:1(0) ack 1001 win 257 <sack 9001:10001,nop,nop>
// we expect rto fired in 1/2*srtt (50ms)
+.05 > . 1001:2001(1000) ack 1
This fix remove the FLAG_SET_XMIT_TIMER from ack_flag when
tcp_check_sack_reneging() set RTO timer with 1/2*srtt to avoid
being overwrited later.
Fixes: 62d9f1a694 ("tcp: fix TLP timer not set when CA_STATE changes from DISORDER to OPEN")
Signed-off-by: Fred Chen <fred.chenchen03@gmail.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit changes the data receiver repath behavior to occur after
receiving a single duplicate. This can help recover ACK connectivity
quicker if a TLP was sent along a nonworking path.
For instance, consider the case where we have an initially nonworking
forward path and reverse path and subsequently switch to only working
forward paths. Before this patch we would have the following behavior.
+---------+--------+--------+----------+----------+----------+
| Event | For FL | Rev FL | FP Works | RP Works | Data Del |
+---------+--------+--------+----------+----------+----------+
| Initial | A | 1 | N | N | 0 |
+---------+--------+--------+----------+----------+----------+
| TLP | A | 1 | N | N | 0 |
+---------+--------+--------+----------+----------+----------+
| RTO 1 | B | 1 | Y | N | 1 |
+---------+--------+--------+----------+----------+----------+
| RTO 2 | C | 1 | Y | N | 2 |
+---------+--------+--------+----------+----------+----------+
| RTO 3 | D | 2 | Y | Y | 3 |
+---------+--------+--------+----------+----------+----------+
This patch gets rid of at least RTO 3, avoiding additional unnecessary
repaths of a working forward path to a (potentially) nonworking one.
In addition, this commit changes the behavior to avoid repathing upon
rx of duplicate data if the local endpoint is in CA_Loss (in which
case the RTOs will already be changing the outgoing flowlabel).
Signed-off-by: David Morley <morleyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Tested-by: David Morley <morleyd@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In order to better estimate whether a data packet has been
retransmitted or is the result of a TLP, we save the last received
ipv6 flowlabel.
To make space for this field we resize the "ato" field in
inet_connection_sock as the current value of TCP_DELACK_MAX can be
fully contained in 8 bits and add a compile_time_assert ensuring this
field is the required size.
v2: addressed kernel bot feedback about dccp_delack_timer()
v3: addressed build error introduced by commit bbf80d713f ("tcp:
derive delack_max from rto_min")
Signed-off-by: David Morley <morleyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Tested-by: David Morley <morleyd@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This commit fixes poor delayed ACK behavior that can cause poor TCP
latency in a particular boundary condition: when an application makes
a TCP socket write that is an exact multiple of the MSS size.
The problem is that there is painful boundary discontinuity in the
current delayed ACK behavior. With the current delayed ACK behavior,
we have:
(1) If an app reads data when > 1*MSS is unacknowledged, then
tcp_cleanup_rbuf() ACKs immediately because of:
tp->rcv_nxt - tp->rcv_wup > icsk->icsk_ack.rcv_mss ||
(2) If an app reads all received data, and the packets were < 1*MSS,
and either (a) the app is not ping-pong or (b) we received two
packets < 1*MSS, then tcp_cleanup_rbuf() ACKs immediately beecause
of:
((icsk->icsk_ack.pending & ICSK_ACK_PUSHED2) ||
((icsk->icsk_ack.pending & ICSK_ACK_PUSHED) &&
!inet_csk_in_pingpong_mode(sk))) &&
(3) *However*: if an app reads exactly 1*MSS of data,
tcp_cleanup_rbuf() does not send an immediate ACK. This is true
even if the app is not ping-pong and the 1*MSS of data had the PSH
bit set, suggesting the sending application completed an
application write.
Thus if the app is not ping-pong, we have this painful case where
>1*MSS gets an immediate ACK, and <1*MSS gets an immediate ACK, but a
write whose last skb is an exact multiple of 1*MSS can get a 40ms
delayed ACK. This means that any app that transfers data in one
direction and takes care to align write size or packet size with MSS
can suffer this problem. With receive zero copy making 4KB MSS values
more common, it is becoming more common to have application writes
naturally align with MSS, and more applications are likely to
encounter this delayed ACK problem.
The fix in this commit is to refine the delayed ACK heuristics with a
simple check: immediately ACK a received 1*MSS skb with PSH bit set if
the app reads all data. Why? If an skb has a len of exactly 1*MSS and
has the PSH bit set then it is likely the end of an application
write. So more data may not be arriving soon, and yet the data sender
may be waiting for an ACK if cwnd-bound or using TX zero copy. Thus we
set ICSK_ACK_PUSHED in this case so that tcp_cleanup_rbuf() will send
an ACK immediately if the app reads all of the data and is not
ping-pong. Note that this logic is also executed for the case where
len > MSS, but in that case this logic does not matter (and does not
hurt) because tcp_cleanup_rbuf() will always ACK immediately if the
app reads data and there is more than an MSS of unACKed data.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Cc: Xin Guo <guoxin0309@gmail.com>
Link: https://lore.kernel.org/r/20231001151239.1866845-2-ncardwell.sw@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SO_MAX_PACING_RATE setsockopt() does not need to hold
the socket lock, because sk->sk_pacing_rate readers
can run fine if the value is changed by other threads,
after adding READ_ONCE() accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 2023 SIGCOMM paper "Improving Network Availability with Protective
ReRoute" has indicated Linux TCP's RTO-triggered txhash rehashing can
effectively reduce application disruption during outages. To better
measure the efficacy of this feature, this patch adds three more
detailed stats during RTO recovery and exports via TCP_INFO.
Applications and monitoring systems can leverage this data to measure
the network path diversity and end-to-end repair latency during network
outages to improve their network infrastructure.
The following counters are added to tcp_sock in order to track RTO
events over the lifetime of a TCP socket.
1. u16 total_rto - Counts the total number of RTO timeouts.
2. u16 total_rto_recoveries - Counts the total number of RTO recoveries.
3. u32 total_rto_time - Counts the total time spent (ms) in RTO
recoveries. (time spent in CA_Loss and
CA_Recovery states)
To compute total_rto_time, we add a new u32 rto_stamp field to
tcp_sock. rto_stamp records the start timestamp (ms) of the last RTO
recovery (CA_Loss).
Corresponding fields are also added to the tcp_info struct.
Signed-off-by: Aananth V <aananthv@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For passive TCP Fast Open sockets that had SYN/ACK timeout and did not
send more data in SYN_RECV, upon receiving the final ACK in 3WHS, the
congestion state may awkwardly stay in CA_Loss mode unless the CA state
was undone due to TCP timestamp checks. However, if
tcp_rcv_synrecv_state_fastopen() decides not to undo, then we should
enter CA_Open, because at that point we have received an ACK covering
the retransmitted SYNACKs. Currently, the icsk_ca_state is only set to
CA_Open after we receive an ACK for a data-packet. This is because
tcp_ack does not call tcp_fastretrans_alert (and tcp_process_loss) if
!prior_packets
Note that tcp_process_loss() calls tcp_try_undo_recovery(), so having
tcp_rcv_synrecv_state_fastopen() decide that if we're in CA_Loss we
should call tcp_try_undo_recovery() is consistent with that, and
low risk.
Fixes: dad8cea7ad ("tcp: fix TFO SYNACK undo to avoid double-timestamp-undo")
Signed-off-by: Aananth V <aananthv@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This idea came after a particular workload requested
the quickack attribute set on routes, and a performance
drop was noticed for large bulk transfers.
For high throughput flows, it is best to use one cpu
running the user thread issuing socket system calls,
and a separate cpu to process incoming packets from BH context.
(With TSO/GRO, bottleneck is usually the 'user' cpu)
Problem is the user thread can spend a lot of time while holding
the socket lock, forcing BH handler to queue most of incoming
packets in the socket backlog.
Whenever the user thread releases the socket lock, it must first
process all accumulated packets in the backlog, potentially
adding latency spikes. Due to flood mitigation, having too many
packets in the backlog increases chance of unexpected drops.
Backlog processing unfortunately shifts a fair amount of cpu cycles
from the BH cpu to the 'user' cpu, thus reducing max throughput.
This patch takes advantage of the backlog processing,
and the fact that ACK are mostly cumulative.
The idea is to detect we are in the backlog processing
and defer all eligible ACK into a single one,
sent from tcp_release_cb().
This saves cpu cycles on both sides, and network resources.
Performance of a single TCP flow on a 200Gbit NIC:
- Throughput is increased by 20% (100Gbit -> 120Gbit).
- Number of generated ACK per second shrinks from 240,000 to 40,000.
- Number of backlog drops per second shrinks from 230 to 0.
Benchmark context:
- Regular netperf TCP_STREAM (no zerocopy)
- Intel(R) Xeon(R) Platinum 8481C (Saphire Rapids)
- MAX_SKB_FRAGS = 17 (~60KB per GRO packet)
This feature is guarded by a new sysctl, and enabled by default:
/proc/sys/net/ipv4/tcp_backlog_ack_defer
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
IP_TRANSPARENT socket option can now be set/read
without locking the socket.
v2: removed unused issk variable in mptcp_setsockopt_sol_ip_set_transparent()
v4: rebased after commit 3f326a821b ("mptcp: change the mpc check helper to return a sk")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fow now, an ACK can update the window in following case, according to
the tcp_may_update_window():
1. the ACK acknowledged new data
2. the ACK has new data
3. the ACK expand the window and the seq of it is valid
Now, we allow the ACK update the window if the window is 0, and the
seq/ack of it is valid. This is for the case that the receiver replies
an zero-window ACK when it is under memory stress and can't queue the new
data.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For now, skb will be dropped when no memory, which makes client keep
retrans util timeout and it's not friendly to the users.
In this patch, we reply an ACK with zero-window in this case to update
the snd_wnd of the sender to 0. Therefore, the sender won't timeout the
connection and will probe the zero-window with the retransmits.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rskq_defer_accept field can be read/written without
the need of holding the socket lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tp->linger2 can be set locklessly as long as readers
use READ_ONCE().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 9ea88a1530 ("tcp: md5: check md5 signature without socket
lock"), the MD5 option is checked in tcp_v[46]_rcv().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230803224552.69398-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_sequence() uses two conditions to decide to drop a packet,
and we currently report generic TCP_INVALID_SEQUENCE drop reason.
Duplicates are common, we need to distinguish them from
the other case.
I chose to not reuse TCP_OLD_DATA, and instead added
TCP_OLD_SEQUENCE drop reason.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230719064754.2794106-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After commit d2ccd7bc8a ("tcp: avoid resetting ACK timer in DCTCP"),
tcp_enter_quickack_mode() is only used from net/ipv4/tcp_input.c.
Fixes: d2ccd7bc8a ("tcp: avoid resetting ACK timer in DCTCP")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20230718162049.1444938-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With modern NIC drivers shifting to full page allocations per
received frame, we face the following issue:
TCP has one per-netns sysctl used to tweak how to translate
a memory use into an expected payload (RWIN), in RX path.
tcp_win_from_space() implementation is limited to few cases.
For hosts dealing with various MSS, we either under estimate
or over estimate the RWIN we send to the remote peers.
For instance with the default sysctl_tcp_adv_win_scale value,
we expect to store 50% of payload per allocated chunk of memory.
For the typical use of MTU=1500 traffic, and order-0 pages allocations
by NIC drivers, we are sending too big RWIN, leading to potential
tcp collapse operations, which are extremely expensive and source
of latency spikes.
This patch makes sysctl_tcp_adv_win_scale obsolete, and instead
uses a per socket scaling factor, so that we can precisely
adjust the RWIN based on effective skb->len/skb->truesize ratio.
This patch alone can double TCP receive performance when receivers
are too slow to drain their receive queue, or by allowing
a bigger RWIN when MSS is close to PAGE_SIZE.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20230717152917.751987-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
request sockets are lockless, __tcp_oow_rate_limited() could be called
on the same object from different cpus. This is harmless.
Add READ_ONCE()/WRITE_ONCE() annotations to avoid a KCSAN report.
Fixes: 4ce7e93cb3 ("tcp: rate limit ACK sent by SYN_RECV request sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this patch, we mainly try to handle sending a compressed ack
correctly if it's deferred.
Here are more details in the old logic:
When sack compression is triggered in the tcp_compressed_ack_kick(),
if the sock is owned by user, it will set TCP_DELACK_TIMER_DEFERRED
and then defer to the release cb phrase. Later once user releases
the sock, tcp_delack_timer_handler() should send a ack as expected,
which, however, cannot happen due to lack of ICSK_ACK_TIMER flag.
Therefore, the receiver would not sent an ack until the sender's
retransmission timeout. It definitely increases unnecessary latency.
Fixes: 5d9f4262b7 ("tcp: add SACK compression")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: fuyuanli <fuyuanli@didiglobal.com>
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://lore.kernel.org/netdev/20230529113804.GA20300@didi-ThinkCentre-M920t-N000/
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230531080150.GA20424@didi-ThinkCentre-M920t-N000
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Our Network Load Balancer (NLB) [0] has multiple nodes with different
IP addresses, and each node forwards TCP flows from clients to backend
targets. NLB has an option to preserve the client's source IP address
and port when routing packets to backend targets. [1]
When a client connects to two different NLB nodes, they may select the
same backend target. Then, if the client has used the same source IP
and port, the two flows at the backend side will have the same 4-tuple.
While testing around such cases, I saw these sequences on the backend
target.
IP 10.0.0.215.60000 > 10.0.3.249.10000: Flags [S], seq 2819965599, win 62727, options [mss 8365,sackOK,TS val 1029816180 ecr 0,nop,wscale 7], length 0
IP 10.0.3.249.10000 > 10.0.0.215.60000: Flags [S.], seq 3040695044, ack 2819965600, win 62643, options [mss 8961,sackOK,TS val 1224784076 ecr 1029816180,nop,wscale 7], length 0
IP 10.0.0.215.60000 > 10.0.3.249.10000: Flags [.], ack 1, win 491, options [nop,nop,TS val 1029816181 ecr 1224784076], length 0
IP 10.0.0.215.60000 > 10.0.3.249.10000: Flags [S], seq 2681819307, win 62727, options [mss 8365,sackOK,TS val 572088282 ecr 0,nop,wscale 7], length 0
IP 10.0.3.249.10000 > 10.0.0.215.60000: Flags [.], ack 1, win 490, options [nop,nop,TS val 1224794914 ecr 1029816181,nop,nop,sack 1 {4156821004:4156821005}], length 0
It seems to be working correctly, but the last ACK was generated by
tcp_send_dupack() and PAWSEstab was increased. This is because the
second connection has a smaller timestamp than the first one.
In this case, we should send a dup ACK in tcp_send_challenge_ack()
to increase the correct counter and rate-limit it properly.
Let's check the SYN flag after the PAWS tests to avoid adding unnecessary
overhead for most packets.
Link: https://docs.aws.amazon.com/elasticloadbalancing/latest/network/introduction.html [0]
Link: https://docs.aws.amazon.com/elasticloadbalancing/latest/network/load-balancer-target-groups.html#client-ip-preservation [1]
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can change tcp_sk() to propagate its argument const qualifier,
thanks to container_of_const().
We have two places where a const sock pointer has to be upgraded
to a write one. We have been using const qualifier for lockless
listeners to clearly identify points where writes could happen.
Add tcp_sk_rw() helper to better document these.
tcp_inbound_md5_hash(), __tcp_grow_window(), tcp_reset_check()
and tcp_rack_reo_wnd() get an additional const qualififer
for their @tp local variables.
smc_check_reset_syn_req() also needs a similar change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_poll() reads sk->sk_err without socket lock held/owned.
We should used READ_ONCE() here, and update writers
to use WRITE_ONCE().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This field can be read/written without lock synchronization.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core
----
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations.
- Add inet drop monitor support.
- A few GRO performance improvements.
- Add infrastructure for atomic dev stats, addressing long standing
data races.
- De-duplicate common code between OVS and conntrack offloading
infrastructure.
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements.
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up
the workload with the number of available CPUs.
- Add the helper support for connection-tracking OVS offload.
BPF
---
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF.
- Make cgroup local storage available to non-cgroup attached BPF
programs.
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers.
- A relevant bunch of BPF verifier fixes and improvements.
- Veristat tool improvements to support custom filtering, sorting,
and replay of results.
- Add LLVM disassembler as default library for dumping JITed code.
- Lots of new BPF documentation for various BPF maps.
- Add bpf_rcu_read_{,un}lock() support for sleepable programs.
- Add RCU grace period chaining to BPF to wait for the completion
of access from both sleepable and non-sleepable BPF programs.
- Add support storing struct task_struct objects as kptrs in maps.
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values.
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions.
Protocols
---------
- TCP: implement Protective Load Balancing across switch links.
- TCP: allow dynamically disabling TCP-MD5 static key, reverting
back to fast[er]-path.
- UDP: Introduce optional per-netns hash lookup table.
- IPv6: simplify and cleanup sockets disposal.
- Netlink: support different type policies for each generic
netlink operation.
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support.
- MPTCP: add netlink notification support for listener sockets
events.
- SCTP: add VRF support, allowing sctp sockets binding to VRF
devices.
- Add bridging MAC Authentication Bypass (MAB) support.
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios.
- More work for Wi-Fi 7 support, comprising conversion of all
the existing drivers to internal TX queue usage.
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading.
- IPSec: extended ack support for more descriptive XFRM error
reporting.
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking.
- IEEE 802154: synchronous send frame and extended filtering
support, initial support for scanning available 15.4 networks.
- Tun: bump the link speed from 10Mbps to 10Gbps.
- Tun/VirtioNet: implement UDP segmentation offload support.
Driver API
----------
- PHY/SFP: improve power level switching between standard
level 1 and the higher power levels.
- New API for netdev <-> devlink_port linkage.
- PTP: convert existing drivers to new frequency adjustment
implementation.
- DSA: add support for rx offloading.
- Autoload DSA tagging driver when dynamically changing protocol.
- Add new PCP and APPTRUST attributes to Data Center Bridging.
- Add configuration support for 800Gbps link speed.
- Add devlink port function attribute to enable/disable RoCE and
migratable.
- Extend devlink-rate to support strict prioriry and weighted fair
queuing.
- Add devlink support to directly reading from region memory.
- New device tree helper to fetch MAC address from nvmem.
- New big TCP helper to simplify temporary header stripping.
New hardware / drivers
----------------------
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches.
- Marvel Prestera AC5X Ethernet Switch.
- WangXun 10 Gigabit NIC.
- Motorcomm yt8521 Gigabit Ethernet.
- Microchip ksz9563 Gigabit Ethernet Switch.
- Microsoft Azure Network Adapter.
- Linux Automation 10Base-T1L adapter.
- PHY:
- Aquantia AQR112 and AQR412.
- Motorcomm YT8531S.
- PTP:
- Orolia ART-CARD.
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices.
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices.
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets.
- Realtek RTL8852BE and RTL8723DS.
- Cypress.CYW4373A0 WiFi + Bluetooth combo device.
Drivers
-------
- CAN:
- gs_usb: bus error reporting support.
- kvaser_usb: listen only and bus error reporting support.
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping.
- implement devlink-rate support.
- support direct read from memory.
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate.
- Support for enhanced events compression.
- extend H/W offload packet manipulation capabilities.
- implement IPSec packet offload mode.
- nVidia/Mellanox (mlx4):
- better big TCP support.
- Netronome Ethernet NICs (nfp):
- IPsec offload support.
- add support for multicast filter.
- Broadcom:
- RSS and PTP support improvements.
- AMD/SolarFlare:
- netlink extened ack improvements.
- add basic flower matches to offload, and related stats.
- Virtual NICs:
- ibmvnic: introduce affinity hint support.
- small / embedded:
- FreeScale fec: add initial XDP support.
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood.
- TI am65-cpsw: add suspend/resume support.
- Mediatek MT7986: add RX wireless wthernet dispatch support.
- Realtek 8169: enable GRO software interrupt coalescing per
default.
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP.
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support.
- add ip6gre support.
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support.
- enable flow offload support.
- Renesas:
- add rswitch R-Car Gen4 gPTP support.
- Microchip (lan966x):
- add full XDP support.
- add TC H/W offload via VCAP.
- enable PTP on bridge interfaces.
- Microchip (ksz8):
- add MTU support for KSZ8 series.
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan.
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support.
- add ack signal support.
- enable coredump support.
- remain_on_channel support.
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities.
- 320 MHz channels support.
- RealTek WiFi (rtw89):
- new dynamic header firmware format support.
- wake-over-WLAN support.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=CbJC
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
The cited commit caused the following build break when CONFIG_IPV6 was
disabled
net/ipv4/tcp_input.c: In function ‘tcp_syn_flood_action’:
include/net/sock.h:387:37: error: ‘const struct sock_common’ has no member named ‘skc_v6_rcv_saddr’; did you mean ‘skc_rcv_saddr’?
Fix by using inet6_rcv_saddr() macro which handles this situation
nicely.
Fixes: d9282e48c6 ("tcp: Add listening address to SYN flood message")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
CC: Matthieu Baerts <matthieu.baerts@tessares.net>
CC: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221122184158.170798-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These cases were done with this Coccinelle:
@@
expression H;
expression L;
@@
- (get_random_u32_below(H) + L)
+ get_random_u32_inclusive(L, H + L - 1)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- + E
- - E
)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- - E
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- - E
+ F
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- + E
+ F
- - E
)
And then subsequently cleaned up by hand, with several automatic cases
rejected if it didn't make sense contextually.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This is a simple mechanical transformation done by:
@@
expression E;
@@
- prandom_u32_max
+ get_random_u32_below
(E)
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Reviewed-by: SeongJae Park <sj@kernel.org> # for damon
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> # for arm
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Annotate the lockless read of queue->synflood_warned.
Following xchg() has the needed data-race resolution.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYN flood message prints the listening port number, but with many
processes bound to the same port on different IPs, it's impossible to
tell which socket is the problem.
Add the listen IP address to the SYN flood message.
For IPv6 use "[IP]:port" as per RFC-5952 and to provide ease of
copy-paste to "ss" filters. For IPv4 use "IP:port" to match.
Each protcol's "any" address and a host address now look like:
Possible SYN flooding on port 0.0.0.0:9001.
Possible SYN flooding on port 127.0.0.1:9001.
Possible SYN flooding on port [::]:9001.
Possible SYN flooding on port [fc00::1]:9001.
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/4fedab7ce54a389aeadbdc639f6b4f4988e9d2d7.1668386107.git.jamie.bainbridge@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
