The line6 driver uses a lot of USB buffers off of the stack, which is
not allowed on many systems, causing the driver to crash on some of
them. Fix this up by dynamically allocating the buffers with kmalloc()
which allows for proper DMA-able memory.
Reported-by: Christo Gouws <gouws.christo@gmail.com>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Christo Gouws <gouws.christo@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
usb_alloc_urb() can fail due to kmalloc failure and push the error
upstream. Further this can cause a NULL pointer dereference in
init_pipe_urbs(). This patch avoids such a scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add an entry to the quirks-table to for usb-audio to recognize the
Microbook II (although it only exposes vendor interfaces). A simple boot
quirk is also implemented to set up the sample rate and make sure that
no audio urbs are sent before the device is ready.
This patch only provides audio playback and capture at 96kHz sample
rate. Notice the following shortcomings:
- The sample rate is currently hardcoded to 96k although the device also
supports 48k and 44.1k.
- The various mixer controls of the MicroBook are not made available.
- The keep-iface control should be on by default because the device
shuts down whenever the altsetting is reset which is usually unwanted.
(I don't know the best way to do this)
- The communication format used by the MicroBook for sample rate setting
and also other setup has been reverse engineered by looking at the
usbmon output while running the windows driver through virtualbox. In
this patch the first byte of every message is set to \0 while in the
observed communications the first byte acts as a "message-counter"
increasing its value with every message sent. Leaving it at \0 does
not seem to affect the device.
Signed-off-by: Manuel Reinhardt <manuel.rhdt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At least some USB devices use (MSB-aligned) audio format larger
than the actual resolution of the device. In order to expose the
actual device resolution (bBitResolution), add extra field to the
procfs stream info interface.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit a60945fd08 ("ALSA: usb-audio: move implicit fb quirks to
separate function") introduced an error in the handling of quirks for
implicit feedback endpoints. This commit fixes this.
If a quirk successfully sets up an implicit feedback endpoint, usb-audio
no longer tries to find the implicit fb endpoint itself.
Fixes: a60945fd08 ("ALSA: usb-audio: move implicit fb quirks to separate function")
Signed-off-by: Manuel Reinhardt <manuel.rhdt@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Simplify the proc fs creation code with new helper functions,
snd_card_ro_proc_new() and snd_card_rw_proc_new().
Just a code refactoring and no functional changes.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_lib_preallocate_pages() and co always succeed, so the error
check is simply redundant. Drop it.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the T+A VID to the generic check in order to enable
native DSD support for T+A devices. This works with the new T+A USB
DAC model SD3100HV and will also work with future devices which
support the XMOS/Thesycon style DSD format.
Signed-off-by: Udo Eberhardt <udo.eberhardt@thesycon.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
XMOS/Thesycon family of USB Audio Class firmware flags DSD altsetting
separate from the PCM ones. Thus the DSD altsetting can be auto-detected
based on the flag and doesn't need maintaining specific altsetting
whitelist.
In addition, static VID:PID-to-altsetting whitelisting causes problems
when firmware update changes the altsetting, or same VID:PID is reused
for another device that has different kind of firmware.
This patch removes existing explicit whitelist mappings for XMOS VID
(0x20b1) and Thesycon VID (0x152a).
Also corrects placement of Hegel HD12 and NuPrime DAC-10 to keep list
sorted based on VID.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds quirk VID/PID IDs for the Opus #3 DAP (made by 'The Bit')
in order to enable Native DSD support.
[ NOTE: this could be handled in the generic way with fp->dvd_raw if
we add 0x10cb to the vendor whitelist, but since 0x10cb shows a
different vendor name (Erantech), put to the individual entry at
this time -- tiwai ]
Signed-off-by: Olek Poplavsky <woodenbits@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull the PCM suspend improvement / cleanup.
This moves the most of snd_pcm_suspend*() calls into PCM's own device
PM ops. There should be no change from the functionality POV.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The call of snd_pcm_suspend_all() & co became superfluous since we
call it in the PCM PM ops. Let's remove them.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes gcc '-Wunused-but-set-variable' warning:
sound/usb/mixer.c: In function 'parse_audio_feature_unit':
sound/usb/mixer.c:1838:28: warning:
variable 'first_ch_bits' set but not used [-Wunused-but-set-variable]
It never used since 2.6
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
fix typo after a recent commit causing headphones to have no sound
Fixes: ad43d528a7 (ALSA: usb-audio: Define registers for CM6206)
Signed-off-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The fix checks if snd_card_register() fails, and if so logs the error
via dev_err() consistent with other patches.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In `create_composite_quirk`, the terminating condition of for loops is
`quirk->ifnum < 0`. So any composite quirks should end with `struct
snd_usb_audio_quirk` object with ifnum < 0.
for (quirk = quirk_comp->data; quirk->ifnum >= 0; ++quirk) {
.....
}
the data field of Bower's & Wilkins PX headphones usb device device quirks
do not end with {.ifnum = -1}, wihch may result in out-of-bound read.
This Patch fix the bug by adding an ending quirk object.
Fixes: 240a8af929 ("ALSA: usb-audio: Add a quirck for B&W PX headphones")
Signed-off-by: Hui Peng <benquike@163.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few places where we access the data without checking the
actual object size from the USB audio descriptor. This may result in
OOB access, as recently reported.
This patch addresses these missing checks. Most of added codes are
simple bLength checks in the caller side. For the input and output
terminal parsers, we put the length check in the parser functions.
For the input terminal, a new argument is added to distinguish between
UAC1 and the rest, as they treat different objects.
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reported-by: Hui Peng <benquike@163.com>
Tested-by: Hui Peng <benquike@163.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've had some sanity checks of the mixer unit descriptors but they
are too loose and some corner cases are overlooked. Add more strict
checks in uac_mixer_unit_get_channels() for avoiding possible OOB
accesses by malformed descriptors.
This also changes the semantics of uac_mixer_unit_get_channels()
slightly. Now it returns zero for the cases where the descriptor
lacks of bmControls instead of -EINVAL. Then the caller side skips
the mixer creation for such unit while it keeps parsing it.
This corresponds to the case like Maya44.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The parser for the processing unit reads bNrInPins field before the
bLength sanity check, which may lead to an out-of-bound access when a
malformed descriptor is given. Fix it by assignment after the bLength
check.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a USB sound card reports 0 interfaces, an error condition is triggered
and the function usb_audio_probe errors out. In the error path, there was a
use-after-free vulnerability where the memory object of the card was first
freed, followed by a decrement of the number of active chips. Moving the
decrement above the atomic_dec fixes the UAF.
[ The original problem was introduced in 3.1 kernel, while it was
developed in a different form. The Fixes tag below indicates the
original commit but it doesn't mean that the patch is applicable
cleanly. -- tiwai ]
Fixes: 362e4e49ab ("ALSA: usb-audio - clear chip->probing on error exit")
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds quirk VID/PID IDs for the SMSL D1 in order to enable
Native DSD support.
[ Moved the added entry in numerical order -- tiwai ]
Signed-off-by: Tony Das <tdas444@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the Dell WD15 Dock, the WD19 Dock (0bda:402e) doens't provide
useful string for the vendor and product names too. In order to share
the UCM with WD15, here we keep the profile_name same as the WD15.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The register map for CM6206 is known and we can define what
the values written to the different registers actually mean.
I tested to print the hex values before/after this change,
there is no functional change.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, add the "fall through" annotation in caiaq driver.
Note that this seems necessary to be put exactly before the next
label, so it's outside the ifdef block.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds several vendor specific mixer quirks for RME's Class Compliant
USB devices. These provide extra status information from the device
otherwise not available.
These include AES/SPDIF rate and status information, current system
sampling rate and measured frequency. This information is especially
useful in cases where device's clock is slaved to external clock
source.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A quirk in snd-usb-audio was added to automate setting sample rate to
4800k and remove the previously exposed nonfunctional microphone for
the Bowers & Wilkins PX:
commit 240a8af929https://lore.kernel.org/patchwork/patch/919689/
However the headphones where updated shortly after that to remove the
unintentional microphone functionality. I guess because of this the
headphones now crash when connecting them via USB while the quirk is
active. Dmesg:
snd-usb-audio: probe of 2-3:1.0 failed with error -22
usb 2-3: 2:1: cannot get min/max values for control 2 (id 2)
This patch removes the microfone and allows the headphones to connect
and work out of the box. It is based on the current mainline kernel
and successfully applied an tested on my machine (4.18.10.arch1-1).
Fixes: 240a8af929 ("ALSA: usb-audio: Add a quirck for B&W PX headphones")
Signed-off-by: Nicolas Huaman <nicolas@herochao.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For discarding the pending bytes on rawmidi, we process with a loop of
snd_rawmidi_transmit() which is just a waste of CPU power.
Implement a lightweight API function to discard the pending bytes and
the proceed the ring buffer instantly, and use it instead of open
codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1357413 ("Missing break in switch")
Addresses-Coverity-ID: 114917 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Fixes: 7edf3b5e6a ("ALSA: usb-audio: AudioStreaming Power Domain parsing")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115084 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pointer 'urb' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'urb' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make use of UAC3 Power Domains associated to an Audio Streaming
path within the PCM's logic. This means, when there is no audio
being transferred (pcm is closed), the host will set the Power Domain
associated to that substream to state D1. When audio is being transferred
(from hw_params onwards), the Power Domain will be set to D0 state.
This is the way the host lets the device know which Terminal
is going to be actively used and it is for the device to
manage its own internal resources on that UAC3 Power Domain.
Note the resume method now sets the Power Domain to D1 state as
resuming the device doesn't mean audio streaming will occur.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the UAC3 Power Domain state for an Audio Streaming interface
to D2 state before suspending the device (usb_driver callback).
This lets the device know there is no intention to use any of the
Units in the Audio Function and that the host is not going to
even listen for wake-up events (interrupts) on the units.
When the usb_driver gets resumed, the state D0 (fully powered) will
be set. This ties up the UAC3 Power Domains to the runtime PM.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power Domains in the UAC3 spec are mainly intended to be
associated to an Input or Output Terminal so the host
changes the power state of the entire capture or playback
path within the topology.
This patch adds support for finding Power Domains associated
to an Audio Streaming Interface (bTerminalLink) and adds a
reference to them in the usb audio substreams (snd_usb_substream).
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Thee USB Audio Class 3 (UAC3) introduces Power Domains as a new
feature to let a host turn individual parts of an audio function
to different power states via USB requests. This lets the device
get to know a bit amore about what the host is up to in order to
optimize power consumption efficiently.
The Power Domains are optional for UAC3 configuration but all
UAC3 devices shall include at least one BADD configuration where
the support for Power Domains is compulsory.
This patch adds a set of features/helpers to parse these power
domains and change their status.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_usb_select_mode_quirk(), snd_usb_set_interface_quirk() and
snd_usb_ctl_msg_quirk() are never called in atomic context.
They call mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Declare snd_usb_feature_unit_ctl properly in mixer.h. Otherwise it's
error-prone.
This fixes the sparse warning:
sound/usb/mixer.c:1464:25: warning: symbol 'snd_usb_feature_unit_ctl' was not declared. Should it be static?
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AU0828_DEVICE() macro in quirks-table.h uses USB_DEVICE_VENDOR_SPEC()
for expanding idVendor and idProduct fields. However, the latter
macro adds also match_flags and bInterfaceClass, which are different
from the values AU0828_DEVICE() macro sets after that.
For fixing them, just expand idVendor and idProduct fields manually in
AU0828_DEVICE().
This fixes sparse warnings like:
sound/usb/quirks-table.h:2892:1: warning: Initializer entry defined twice
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds native DSD playback support for the Encore mDSD USB DAC by
specifying the vendor and product ID's
Signed-off-by: Jeff Crukley <jcrukley@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Thesycon provides solutions to XMOS chips, and has its own device
vendor id.
In this patch, we use generic method to detect DSD capability of
Thesycon-based UAC2 implementations in order to support a wide range
of current and future devices.
The patch will enable the SNDRV_PCM_FMTBIT_DSD_U32_BE bit for the DAC
hence enable native DSD playback up to DSD512 format.
Signed-off-by: Yue Wang <yuleopen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the audio device is externally clocked and set to a rate that does
not match the external clock, the clock will never be valid and we cannot
set the rate successfully. To fix this, allow a rate change even if
the clock is initially invalid, and validate again after the rate is
changed.
This fixes problems with MOTU UltraLite AVB hardware over USB.
Signed-off-by: Adam Goode <agoode@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_lib_mmap_vmalloc() was supposed to be implemented with
somewhat special for vmalloc handling, but in the end, this turned to
just the default handler, i.e. NULL. As the situation has never
changed over decades, let's rip it off.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch refactors the processing units min/max calculation logic
for the mixer controls and fixes an issue where the Mode Select
checking of the Up/Down mixers doesn't differentiate between the
UAC1 and UAC2 Control Selector (0x02) and the UAC3 one which is
different (0x01).
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Audio Control interface descriptor subtypes do not match
across all the UAC versions. That makes reusability of the
"virtual type" (Mixer, Processors, Selectors, etc) terminals
difficult. It also makes the mixer get the default names for
the virtual terminals wrong due to the overlap.
This patch proposes an unified approach by always using the most
comprehensive spec version to define them all (in this case UAC3).
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the Processig Units defined in
the UAC3 spec. The main difference with the previous specs
is the lack of on/off switches in the controls for these
units and the addiction of the new Multi Function Processing
Unit.
The current version of the UAC3 spec doesn't define any
useful controls for the new Multi Function Processing Unit
so no control will get created once this unit is parsed.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current support for UAC2 Processing Units does the parsing
as one control per bit in the bitmap. However, the UAC2 spec
defines the controls as bit pairs where b01 means read-only
and b11 means read/write control.
This patch fixes that and uses the helper functions for checking
controls readability/writability when the control is defined as
bit pairs (UAC2 and UAC3).
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
