This patch adds tracepoints to the target code for commands being
received and being completed, which is quite useful for debugging
interactions with initiators. For example, one can do something like the
following to watch commands that are completing unsuccessfully:
# echo 'scsi_status!=0' > /sys/kernel/debug/tracing/events/target/target_cmd_complete/filter
# echo 1 > /sys/kernel/debug/tracing/events/target/target_cmd_complete/enable
<run command that fails>
# cat /sys/kernel/debug/tracing/trace
iscsi_trx-0-1902 [003] ...1 990185.810385: target_cmd_complete: iqn.1993-08.org.debian:01:e51ede6aacfd <- LUN 001 status CHECK CONDITION (sense len 18 / 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00) 0x95 data_length 512 CDB 95 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 (TA:SIMPLE C:00)
(v2: Drop undefined COMPARE_AND_WRITE)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where RDMA_CM_EVENT_DISCONNECTED may occur
before the connection shutdown has been completed by rx/tx threads,
that causes isert_free_conn() to wait indefinately on ->conn_wait.
This patch allows isert_disconnect_work code to invoke rdma_disconnect
when isert_disconnect_work() process context is started by client
session reset before isert_free_conn() code has been reached.
It also adds isert_conn->conn_mutex protection for ->state within
isert_disconnect_work(), isert_cq_comp_err() and isert_free_conn()
code, along with isert_check_state() for wait_event usage.
(v2: Add explicit iscsit_cause_connection_reinstatement call
during isert_disconnect_work() to force conn reset)
Cc: stable@vger.kernel.org # 3.10+
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds target_get_sess_cmd reference counting for
iscsit_handle_task_mgt_cmd(), and adds a target_put_sess_cmd()
for the failure case.
It also fixes a bug where ISCSI_OP_SCSI_TMFUNC type commands
where leaking iscsi_cmd->i_conn_node and eventually triggering
an OOPs during struct isert_conn shutdown.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves ISCSI_OP_REJECT failures into iscsit_sequence_cmd()
in order to avoid external iscsit_reject_cmd() reject usage for all
PDU types.
It also updates PDU specific handlers for traditional iscsi-target
code to not reset the session after posting a ISCSI_OP_REJECT during
setup.
(v2: Fix CMDSN_LOWER_THAN_EXP for ISCSI_OP_SCSI to call
target_put_sess_cmd() after iscsit_sequence_cmd() failure)
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsit_add_reject() + iscsit_add_reject_from_cmd()
usage to not sleep on iscsi_cmd->reject_comp to address a free-after-use
usage bug in v3.10 with iser-target code.
It saves ->reject_reason for use within iscsit_build_reject() so the
correct value for both transport cases. It also drops the legacy
fail_conn parameter usage throughput iscsi-target code and adds
two iscsit_add_reject_cmd() and iscsit_reject_cmd helper functions,
along with various small cleanups.
(v2: Re-enable target_put_sess_cmd() to be called from
iscsit_add_reject_from_cmd() for rejects invoked after
target_get_sess_cmd() has been called)
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the missing isert_put_reject() logic to post
a outgoing payload buffer to hold the 48 bytes of original PDU
header request payload for the rejected cmd.
It also fixes ISTATE_SEND_REJECT handling in isert_response_completion()
-> isert_do_control_comp() code, and drops incorrect iscsi_cmd_t->reject_comp
usage.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix-up breakage in iscsit_build_sendtargets_response() from v3.11
changes, and free "payload" before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All REJECT response setup of the rejected payload is now done using
on-demand cmd->buf_ptr allocations.
Go ahead and remove dead iscsi_conn->bad_hdr usage rx_opcode path
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix up sense_reason_t breakage in core_scsi3_update_and_write_aptpl()
from recent conversion to use local scope memory allocation.
Reported as sparse warnings: (new ones prefixed by >>) by Fengguang:
>> drivers/target/target_core_pr.c:2069:57: sparse: incorrect type in
>> return expression (different base types)
drivers/target/target_core_pr.c:2069:57: expected restricted sense_reason_t
drivers/target/target_core_pr.c:2069:57: got int
>> drivers/target/target_core_pr.c:2179:21: sparse: incorrect type in
>> assignment (different base types)
drivers/target/target_core_pr.c:2179:21: expected restricted sense_reason_t [assigned] [usertype] ret
drivers/target/target_core_pr.c:2179:21: got int
>> drivers/target/target_core_pr.c:2197:13: sparse: incorrect type in
>> assignment (different base types)
drivers/target/target_core_pr.c:2197:13: expected restricted sense_reason_t [assigned] [usertype] ret
drivers/target/target_core_pr.c:2197:13: got int
drivers/target/target_core_pr.c:1245:28: sparse: context imbalance in '__core_scsi3_free_registration' - unexpected unlock
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a auth configfs group context following existing
explict NodeACL and discovery auth within:
/sys/kernel/config/target/iscsi/$TARGETNAME/$TPGT/auth/
This patch allows these attributes to be used for CHAP authentication
an TPG is configured in demo-mode (generate_node_acl=1).
Note this authentication information takes precedence over NodeACL
authentication when struct se_node_acl->dynamic_node_acl is present.
Cc: Dax Kelson <dkelson@gurulabs.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an optional /auth/ configfs group to TPG context that
can be used by fabrics like iscsi-target for TPG demo-mode
authentication.
Cc: Dax Kelson <dkelson@gurulabs.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes ISCSI_OP_TEXT handling of SendTargets=[iqn.,eui.]
payloads to return explicit discovery information.
It adds checks to iscsit_process_text_cmd() and adds the special single
$TARGETNAME discovery case in iscsit_build_sendtargets_response() code.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves ISCSI_OP_TEXT PDU buffer sanity checks to
iscsit_process_text_cmd() code, so that it can be shared
with iser-target code.
It adds IFC_SENDTARGETS_ALL + iscsi_cmd->text_in_ptr in order
to save text payload for ISCSI_OP_TEXT_RSP, and updates
iscsit_release_cmd() to assigned memory.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsi_set_connection_parameters() to allow
conn_ops->MaxXmitDataSegmentLength assignement to occur during
in-band iser send-targets discovery, as this value is required
by TEXT response processing code.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactoring existing iscsit_send_text_rsp() in order
to handle iscsi_text_rsp payloads in a transport specific manner.
This includes the addition of iscsit_build_text_rsp() to build
the response payload and initialize ISCSI_OP_TEXT_RSP.
v2: Make iscsit_build_text_rsp() determine extra padding bytes, and
drop legacy padding calculation for traditional iSCSI text
responses within iscsit_send_text_rsp()
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors ISCSI_OP_TEXT handling within iscsi-target in
order to handle iscsi_text payloads in a transport specific manner.
This includes splitting current iscsit_handle_text_cmd() into
iscsit_setup_text_cmd() and iscsit_process_text_cmd() calls, and
makes iscsit_handle_text_cmd be only used internally by traditional
iscsi socket calls.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors ISCSI_OP_NOOP handling within iscsi-target in
order to handle iscsi_nopout payloads in a transport specific manner.
This includes splitting existing iscsit_handle_nop_out() into
iscsit_setup_nop_out() and iscsit_process_nop_out() calls, and
makes iscsit_handle_nop_out() be only used internally by traditional
iscsi socket calls.
Next update iser-target code to use new callers and add FIXME for
the handling iscsi_nopout payloads. Also fix reject response handling
in iscsit_setup_nop_out() to use proper iscsit_add_reject_from_cmd().
v2: Fix uninitialized iscsit_handle_nop_out() payload_length usage (Fengguang)
v3: Remove left-over dead code in iscsit_setup_nop_out() (DanC)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Comment from original 2012 patch:
In all our testing this function has never returned true. However, the
dropping of hardware_lock necessary to call this function seems to cause
a use-after-free we manage to hit rather frequently. Given this
cost-benefit ratio, I'm willing to remove some 100 lines of code.
And since the same problem exists around shutdown_sess and put_sess,
this patch changes them from taking the hardware_lock to requiring the
hardware_lock to be taken. In most cases the caller already had the
lock and had to drop it for the called method to reacquire it. At best
that hurts performance and in rare instances it causes races with fatal
consequences.
We dropped the original 2012 patch when upgrading our kernel and it took
us nearly half a year to discover we still need it.
(nab: Fix qla_tgt_sess reference in tcm_qla2xxx_put_sess)
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch coverts vhost/scsi to se_cmd->cmd_kref TARGET_SCF_ACK_KREF
usage, instead of assuming that vhost_scsi_free_cmd() is always called
before TCM processing is completed in the response fast path.
This includes adding vhost_scsi_check_stop_free() -> target_put_sess_cmd()
to perform the second se_cmd->cmd_kref put, and moving vhost_scsi_free_cmd()
resource release into tcm_vhost_release_cmd() that is invoked once the last
se_cmd->cmd_kref put occurs.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Asias He <asias@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes vhost_scsi_free_cmd() to call transport_generic_free_cmd()
with wait_for_tasks=false in order to avoid the extra se_cmd->t_state_lock
access for the wait_for_tasks=true case.
This is unnecessary because vhost_scsi_free_cmd() is only ever called by
vhost_scsi_complete_cmd_work() after TCM completion handoff, and by
vhost_scsi_handle_vq() exception code before TCM submission handoff, so
there is never a case where se_cmd is still active from TCM's perspective
when transport_generic_free_cmd() is called.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Asias He <asias@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now with iscsi-target using modern se_cmd->cmd_kref accounting in
v3.10 code, it's safe to go ahead and drop the legacy release
codepath + se_cmd->check_release bit in transport_release_cmd()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In modern iscsi-target code, the setup and I/O submission is done within a
single process context, so there is no need to acquire se_cmd->t_state_lock while
checking SCF_SUPPORTED_SAM_OPCODE for determining when unsolicited data-out
should be dumped.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops the se_cmd->t_state_lock access around SCF_SUPPORTED_SAM_OPCODE
assignment within target_setup_cmd_from_cdb().
Original v4.0 target code required this as fabrics would be checking for
this values in different process contexts for setup and I/O submission.
Given that modern v4.1 target code performs setup and I/O submission
from the same process context, this t_state_lock access is no longer
required.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes target_execute_cmd() set CMD_T_BUSY|CMD_T_SENT while
holding se_cmd->t_state_lock, in order to avoid the extra aquire/release
in __target_execute_cmd().
It also clears these bits in case of a target_handle_task_attr()
failure.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes legacy se_cmd->t_fe_count usage in order to avoid
se_cmd->t_state_lock access within transport_put_cmd() during normal
fast path se_cmd descriptor release.
Also drop the left-over parameter usage within core_tmr_handle_tas_abort()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops an unnecessary acquire/release of se_cmd->t_state_lock within
transport_lun_remove_cmd() when checking CMD_T_DEV_ACTIVE for invoking
target_remove_from_state_list().
For all fast path completion cases, transport_lun_remove_cmd() is always
called ahead of transport_cmd_check_stop(), and since transport_cmd_check_stop()
is calling target_remove_from_state_list() when remove_from_lists=true,
the t_state_lock usage in transport_lun_remove_cmd() can safely be removed.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new transport_cmd_check_stop() parameter for signaling
when TRANSPORT_WRITE_PENDING needs to be set.
This allows transport_generic_new_cmd() to avoid the extra lock acquire/release
of ->t_state_lock in the fast path for DMA_TO_DEVICE operations ahead of
transport_cmd_check_stop() + se_tfo->write_pending().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nobody should be expecting to read or write virtual_lun0.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use bool params when appropriate.
Eliminate unneeded pr_reg_e and type variables.
Just one goto label, so rename to 'out' from 'out_put_pr_reg'.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Don't need goto, we can just do an if/else for sa_res_key behavior. Move
shorter case first. Slightly shorter b/c both cases can share a call to
update_and_write_aptpl() now.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of taking the buffer and length, update_and_write_aptpl() will
allocate the buffer as needed, and then free it. Instead, the function
takes an 'aptpl' boolean parameter.
This enables us to remove memory alloc/frees from struct
t10_pr_registration and other spots.
There is a slight loss of functionality because each callsite doesn't get
its own pr_debug any more, but this info can be cleaned via ftrace if
necessary and I think the shorter code is worth it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As mentioned in the comments in update_and_write_aptpl,
write_aptpl_to_file() calls strlen() on the buffer, and the length was
always being passed as zero.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's only ever set to PR_APTPL_BUF_LEN, so we don't need a variable.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The __ version is only ever called from the regular version, so just
inline it. It's not too much more complex to handle both spinlocks in the
same function.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simpler to just set buf in update_and_write_aptpl(), rather than passing
down to ____core_scsi3_update_aptpl_buf().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
They're in emulate_pro_register, so change UNREGISTER to REGISTER.
The first one seems wrong -- sa_res_key could be 0 there, but it's testing
spec_i_pt.
Remove unneeded parens in 2nd conditional.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We use this function exclusively in debug prints. Instead of returning
0 or 1 if isid is present, just set buf to "" if it isn't there. This
saves callers from having to check the return value.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
core_scsi3_enulate_pro_register took an 'ignore_key' parameter that
really distinguished between REGISTER and REGISTER_AND_IGNORE_EXISTING_KEY
registration types, which was a little confusing. Same situation for
PREEMPT and PREEMPT_AND_ABORT. Use enums to add a little more
descriptiveness to the code.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull timer fixes from Thomas Gleixner:
- Trivial: unused variable removal
- Posix-timers: Add the clock ID to the new proc interface to make it
useful. The interface is new and should be functional when we reach
the final 3.10 release.
- Cure a false positive warning in the tick code introduced by the
overhaul in 3.10
- Fix for a persistent clock detection regression introduced in this
cycle
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Correct run-time detection of persistent_clock.
ntp: Remove unused variable flags in __hardpps
posix-timers: Show clock ID in proc file
tick: Cure broadcast false positive pending bit warning
This branch contains a set of straight forward bug fixes to the
irqdomain code and to a couple of drivers that make use of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=wZCk
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux
Pull irqdomain bug fixes from Grant Likely:
"This branch contains a set of straight forward bug fixes to the
irqdomain code and to a couple of drivers that make use of it."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux:
irqchip: Return -EPERM for reserved IRQs
irqdomain: document the simple domain first_irq
kernel/irq/irqdomain.c: before use 'irq_data', need check it whether valid.
irqdomain: export irq_domain_add_simple
The irqdomain core will report a log message for any attempted map call
that fails unless the error code is -EPERM. This patch changes the
Versatile irq controller drivers to use -EPERM because it is normal for
a subset of the IRQ inputs to be marked as reserved on the various
Versatile platforms.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The first_irq needs to be zero to get a linear domain and that
comes with special semantics. We want to simplify this going
forward but some documentation never hurts.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Since irq_data may be NULL, if so, we WARN_ON(), and continue, 'hwirq'
which related with 'irq_data' has to initialize later, or it will cause
issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
All other irq_domain_add_* functions are exported already, and apparently
this one got left out by mistake, which causes build errors for ARM
allmodconfig kernels:
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-rcar.ko] undefined!
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-em.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Another week, another batch of fixes for arm-soc platforms.
Nothing controversial here, a handful of fixes for regressions and/or
serious problems across several of the platforms. Things are slowing
down nicely on fix rates for 3.10.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BUV/
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes for arm-soc platforms.
Nothing controversial here, a handful of fixes for regressions and/or
serious problems across several of the platforms. Things are slowing
down nicely on fix rates for 3.10"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: exynos: add debug_ll_io_init() call in exynos_init_io()
ARM: EXYNOS: uncompress - print debug messages if DEBUG_LL is defined
ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
sh-pfc: r8a7779: Don't group USB OVC and PENC pins
ARM: mxs: icoll: Fix interrupts gpio bank 0
ARM: imx: clk-imx6q: AXI clock select index is incorrect
ARM: bcm2835: override the HW UART periphid
ARM: mvebu: Fix bug in coherency fabric low level init function
ARM: Kirkwood: TS219: Fix crash by double PCIe instantiation
ARM: ux500: Provide supplies for AUX1, AUX2 and AUX3
ARM: ux500: Only configure wake-up reasons on ux500 based platforms
ARM: dts: imx: fix clocks for cspi
ARM i.MX6q: fix for ldb_di_sels
Pull MIPS fixes from Ralf Baechle:
"MIPS fixes across the field. The only area that's standing out is the
exception handling which received it's dose of breakage as part of the
microMIPS patchset"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: add missing SZ_1M multiplier
MIPS: Compat: Fix cputime_to_timeval() arguments in compat binfmt_elf.
MIPS: OCTEON: Improve _machine_halt implementation.
MIPS: rtlx: Fix implicit declaration of function set_vi_handler()
MIPS: Trap exception handling fixes
MIPS: Quit exposing Kconfig symbols in uapi headers.
MIPS: Remove duplicate definition of check_for_high_segbits.
