The clock drivers on imx8m series are registered as platform devices and
this opens the possibility of reloading the driver at runtime.
This doesn't actually work: clocks are never removed and attempting to
bind again results in registration errors and a crash. Almost all
devices depend on clocks anyway so rebinding is unlikely to ever be
useful
Fix this by explicitly suppressing bind attrs like several other
clock drivers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a typo in the watchdog2 clock name.
Fix it by changing it to "wdg2".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The /2 divider between pll4_audio_div and pll4_post_div is not working
on imx6q. The frequency is not halved as reported by the clock tree
and measured on clko.
In the technical reference manual the divider was removed in revision 4.
It's also not listed in the imx6qp manual.
imx6dl manual mentions a divider for PLL4 and the according register
description. So keep the divider here.
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DRAM frequency switches are executed in firmware and can change the
configuration of the DRAM PLL outside linux. Mark these CLKs with
CLK_GET_RATE_NOCACHE so we always read back the PLL config registers and
recalculate rates.
In current DRAM frequency tables on 8mm/8mn only the maximum frequency
uses the PLL so it's always configured in the same way. However reading
back the PLL configuration is the correct behavior and allows additional
setpoints in the future.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These clocks are only modified as part of DRAM frequency switches during
which DRAM itself is briefly inaccessible. The switch is performed with
a SMC call to by TF-A which runs from a SRAM area; upon returning to
linux several clocks bits are modified and we need to update them.
For rate bits an easy solution is to just mark with
CLK_GET_RATE_NOCACHE so that new rates are always read back from
registers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a lock to divider in the composite driver, but that's not
enough. lock to gate/mux are also needed to provide exclusive access
to the register.
Fixes: d3ff972813 ("clk: imx: Add imx composite clock")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no need to initialize flags as 0.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
then a bunch of driver updates and a handful of new drivers. In terms of
diffstat the Qualcomm and Amlogic drivers are high up there because of all the
clk data introcued by new drivers. The Nvidia Tegra driver had a lot of work
done this cycle too to support suspend/resume and memory controllers. And the
OMAP clk driver got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data, mark things
static, correct incorrect data in drivers, etc. All the little things that
improve drivers and maintain code health. I will point out that there's a patch
in here for the GPIO clk driver, that almost nobody uses, which changes
behavior and causes clk_set_rate() to try to change the GPIO gate clk's parent.
Other than that things are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8 SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system suspend/resume cycle
on exynos542x SoCs
-----BEGIN PGP SIGNATURE-----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=qJNg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This merge window we have one small clk provider API in the core
framework and then a bunch of driver updates and a handful of new
drivers. In terms of diffstat the Qualcomm and Amlogic drivers are
high up there because of all the clk data introcued by new drivers.
The Nvidia Tegra driver had a lot of work done this cycle too to
support suspend/resume and memory controllers. And the OMAP clk driver
got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data,
mark things static, correct incorrect data in drivers, etc. All the
little things that improve drivers and maintain code health. I will
point out that there's a patch in here for the GPIO clk driver, that
almost nobody uses, which changes behavior and causes clk_set_rate()
to try to change the GPIO gate clk's parent. Other than that things
are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe
suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8
SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system
suspend/resume cycle on exynos542x SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (160 commits)
clk: aspeed: Add RMII RCLK gates for both AST2500 MACs
MAINTAINERS: Add entry for BM1880 SoC clock driver
clk: Add common clock driver for BM1880 SoC
dt-bindings: clock: Add devicetree binding for BM1880 SoC
clk: Add clk_hw_unregister_composite helper function definition
clk: Zero init clk_init_data in helpers
clk: ingenic: Allow drivers to be built with COMPILE_TEST
MAINTAINERS: Update section for Ux500 clock drivers
clk: mark clk_disable_unused() as __init
clk: Fix memory leak in clk_unregister()
clk: Ingenic: Add CGU driver for X1000.
dt-bindings: clock: Add X1000 bindings.
clk: tegra: Use match_string() helper to simplify the code
clk: pxa: fix one of the pxa RTC clocks
clk: sprd: Use IS_ERR() to validate the return value of syscon_regmap_lookup_by_phandle()
clk: armada-xp: remove unused code
clk: tegra: Fix build error without CONFIG_PM_SLEEP
clk: tegra: Add missing stubs for the case of !CONFIG_PM_SLEEP
clk: tegra: Optimize PLLX restore on Tegra20/30
clk: tegra: Add suspend and resume support on Tegra210
...
It is not correct that sys3_pll_out use sys2_pll1_ref_sel as parent.
According to the current imx_clk_sccg_pll design, it uses both
bypass1/2, however set bypass2 as 1 is not correct, because it will
make sys[x]_pll_out use wrong parent and might access wrong registers.
So correct bypass2 to 0 and fix sys3_pll_out_sels.
Fixes: e9dda4af68 ("clk: imx: Refactor entire sccg pll clk")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The mipi pll clock comes from the MIPI PHY PLL output, so
it should not be a fixed clock.
MIPI PHY PLL is in the MIPI DSI space, and it is used as
the bit clock for transferring the pixel data out and its
output clock is configured according to the display mode.
So it should be used only for MIPI DSI and not be exported
out for other usages.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
During cpu frequency switching the main "CLK_ARM" is reparented to an
intermediate "step" clock. On imx8mm and imx8mn the 24M oscillator is
used for this purpose but it is extremely slow, increasing wakeup
latencies to the point that i2c transactions can timeout and system
becomes unresponsive.
Fix by switching the "step" clk to SYS_PLL1_800M, matching the behavior
of imx8m cpufreq drivers in imx vendor tree.
This bug was not immediately apparent because upstream arm64 defconfig
uses the "performance" governor by default so no cpufreq transitions
happen.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Cc: stable@vger.kernel.org
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/f5d2b9c53f1ed5ccb1dd3c6624f56759d92e1689.1571771777.git.leonard.crestez@nxp.com
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
imx_obtain_fixed_clk_hw could be used to simplify code to replace
__clk_get_hw(of_clk_get_by_name(node, "name"))
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_obtain_fixed_clk_hw could be used to simplify code to replace
__clk_get_hw(of_clk_get_by_name(node, "name"))
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_obtain_fixed_clk_hw could be used to simplify code to replace
__clk_get_hw(of_clk_get_by_name(node, "name"))
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_obtain_fixed_clk_hw could be used to simplify code to replace
__clk_get_hw(of_clk_get_by_name(node, "name"))
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In the latest reference manual Rev.0,06/2019, the DDR clock mux
is extended to 2 bits, and the clock options are also changed,
correct them accordingly.
Fixes: b1260067ac ("clk: imx: add imx7ulp clk driver")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According Architecture definition guide, SYS1_PLL is fixed at
800MHz, SYS2_PLL is fixed at 1000MHz, so let's use imx_clk_fixed
to register the clocks and drop code that could change the rate.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According Architecture definition guide, SYS_PLL1 is fixed at
800MHz, SYS_PLL2 is fixed at 1000MHz, so let's use imx_clk_fixed
to register the clocks and drop code that could change the rate.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According Architecture definition guide, SYS_PLL1 is fixed at
800MHz, SYS_PLL2 is fixed at 1000MHz, so let's use imx_clk_fixed
to register the clocks and drop code that could change the rate.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx8mn there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate. Only one of these gates (the one "dividing" by
one) is currently defined and it's incorrectly set as the parent of all
the fixed-factor dividers.
Add the other 8 gates to the clock tree between sys_pll1/2_bypass and
the fixed dividers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx8mm there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate. Only one of these gates (the one "dividing" by
one) is currently defined and it's incorrectly set as the parent of all
the fixed-factor dividers.
Add the other 8 gates to the clock tree between sys_pll1/2_bypass and
the fixed dividers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx8mq there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate but these gates are not currently defined in
the clock tree.
Add them between sys1/2_pll_out and the fixed dividers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix sparse warnings:
drivers/clk/imx/clk-pll14xx.c:44:37:
warning: symbol 'imx_pll1416x_tbl' was not declared. Should it be static?
drivers/clk/imx/clk-pll14xx.c:57:37:
warning: symbol 'imx_pll1443x_tbl' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This clock is needed by DCSS when high resolutions are used.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@nxp.com>
CC: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use common 1413X/1416X PLL clock structure to save a lot
of duplicated code on i.MX8MN clock driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Many i.MX8M SoCs use same 1443X/1416X PLL, such as i.MX8MM,
i.MX8MN and later i.MX8M SoCs, moving these PLL definitions
to pll14xx driver can save a lot of duplicated code on each
platform.
Meanwhile, no need to define PLL clock structure for every
module which uses same type of PLL, e.g., audio/video/dram use
1443X PLL, arm/gpu/vpu/sys use 1416X PLL, define 2 PLL clock
structure for each group is enough.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PLL14xx on imx8m can change the S and K parameter without requiring
a reset and relock of the whole PLL.
Fix clk_pll144xx_mp_change register reading and use it for pll1443 as
well since no reset+relock is required on K changes either.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pll BYPASS bit should be kept inside pll driver for glitchless freq
setting following spec. If exposing the bit, that means pll driver and
clk driver has two paths to touch this bit, which is wrong.
So use EXT_BYPASS bit here.
And drop uneeded set parent, because EXT_BYPASS default is 0.
Suggested-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-5-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pll BYPASS bit should be kept inside pll driver for glitchless freq
setting following spec. If exposing the bit, that means pll driver and
clk driver has two paths to touch this bit, which is wrong.
So use EXT_BYPASS bit here.
And drop uneeded set parent, because EXT_BYPASS default is 0.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Suggested-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-4-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When registering the PLL, unbypass the PLL.
The PLL has two bypass control bit, BYPASS and EXT_BYPASS.
we will expose EXT_BYPASS to clk driver for mux usage, and keep
BYPASS inside pll14xx usage. The PLL has a restriction that
when M/P change, need to RESET/BYPASS pll to avoid glitch, so
we could not expose BYPASS.
To make it easy for clk driver usage, unbypass PLL which does
not hurt current function.
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-3-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to PLL1443XA and PLL1416X spec,
"When BYPASS is 0 and RESETB is changed from 0 to 1, FOUT starts to
output unstable clock until lock time passes. PLL1416X/PLL1443XA may
generate a glitch at FOUT."
So set BYPASS when RESETB is changed from 0 to 1 to avoid glitch.
In the end of set rate, BYPASS will be cleared.
When prepare clock, also need to take care to avoid glitch. So
we also follow Spec to set BYPASS before RESETB changed from 0 to 1.
And add a check if the RESETB is already 0, directly return 0;
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-2-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The AUDIO PLL max support 650M, so the original clk settings violate
spec. This patch makes the output 786432000 -> 393216000,
and 722534400 -> 361267200 to aligned with NXP vendor kernel without any
impact on audio functionality and go within 650MHz PLL limit.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN supports CPU running at 1.5GHz/1.4GHz/1.2GHz, add missing
frequency for ARM PLL table.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add .rate_count assignment which is necessary for searching required
PLL rate from the each PLL table.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To Frac pll, the gate shift is 13, however to Int PLL the gate shift
is 11.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is enabled by default but if it's not explicitly defined and marked
as critical then its parent might get turned off.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* Replace to audio_pll2_clk with audio_pll2_out
* Replace sys3_pll2_out with sys_pll3_out
* Replace sys1_pll_40m with sys_pll1_40m
* qspi parent[2] is sys_pll2_333m not sys_pll1_800m
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* There is no video_pll2 on imx8mm, replace with dummy
* Replace reference to sys_pll3_clk with sys_pll3_out
* qspi parent[2] is sys_pll2_333m not sys_pll1_800m
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "sys3_pll2_out" CLK was removed in refactoring so all references
need to be updated to "sys3_pll_out"
Fixes: e9dda4af68 ("clk: imx: Refactor entire sccg pll clk")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When of_clk_add_provider failed, all clks should be unregistered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When of_clk_add_provider failed, all clks should be unregistered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Initially, the TMU_ROOT clock was marked as critical, which automatically
made the AHB clock to stay always on. Since the TMU_ROOT clock is not
marked as critical anymore, following commit:
"clk: imx8mq: Remove CLK_IS_CRITICAL flag for IMX8MQ_CLK_TMU_ROOT"
all the clocks that derive from ipg_root clock (and implicitly ahb clock)
would also have to enable, along with their own gate, the AHB clock.
But considering that AHB is actually a bus that has to be always on, we mark
it as critical in the clock provider driver and then all the clocks that
derive from it can be controlled through the dedicated per IP gate which
follows after the ipg_root clock.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Call imx_register_uart_clocks() API to keep uart clocks enabled
when earlyprintk or earlycon is active.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_register_uart_clocks_hws() function is NOT implemented
at all, remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Earlycon's clock could be disabled during kernel boot up,
if earlycon is enabled and its clock is gated, then kernel
boot up will fail. Make sure earlycon's clock is enabled
during kernel boot up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no strong reason for this to use CLK_OF_DECLARE instead
of being a platform driver. Plus, this will now be aligned with the
other i.MX8M clock drivers which are platform drivers.
In order to make the clock provider a platform driver
all the data and code needs to be outside of .init section.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The AUDIO PLL max support 650M, so the original clk settings violate
spec. This patch makes the output 786432000 -> 393216000,
and 722534400 -> 361267200 to aligned with NXP vendor kernel without any
impact on audio functionality and go within 650MHz PLL limit.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has no sys3_pll2_out clock, PWM3 clock's mux option #4
should be sys_pll3_out, sys3_pll2_out is a typo, fix it.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that the i.MX6 and i.MX7 clock drivers have been switched to clk_hw based,
we can remove the clk based API that is not used by any i.MX clock driver.
The following APIs are going away now:
- imx_clk_busy_divider
- imx_clk_busy_mux
- imx_clk_fixup_divider
- imx_clk_fixup_mux
- imx_clk_mux_ldb
- imx_clk_gate_dis_flags
- imx_clk_gate_flags
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per latest imx8mq datasheet of CCM, the parent of usb1_ctrl_root_clk
and usb2_ctrl_root_clk is usb_bus.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IMX8MQ_CLK_TMU_ROOT is ONLY used for thermal module, the driver
should manage this clock, so no need to have CLK_IS_CRITICAL flag
set.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename 'share_count_dcss' to 'share_count_disp', since the
DCSS module does not exist on imx8mm platform. So rename it
to avoid any unnecessary confusion.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per latest imx8mm datasheet of CCM, the parent of usb1_ctrl_root_clk
should be usb_bus.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For i.MX clock drivers probe fail case, clks should be unregistered
in the return path, this patch adds a common API for i.MX clock
drivers to unregister clocks when fail.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1416X/1443X PLL are used on i.MX8MM and i.MX8MN and maybe
other i.MX8M series SoC later, the macro definitions of
these PLLs' initialization should be common for usage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
- Support for CPU clks on Raspberry Pi devices
- Slow clk support for AT91 SAM9X60 SoCs
* clk-rpi-cpufreq:
clk: raspberrypi: register platform device for raspberrypi-cpufreq
firmware: raspberrypi: register clk device
clk: bcm283x: add driver interfacing with Raspberry Pi's firmware
clk: bcm2835: remove pllb
* clk-tegra:
clk: tegra: Do not enable PLL_RE_VCO on Tegra210
clk: tegra: Warn if an enabled PLL is in IDDQ
clk: tegra: Do not warn unnecessarily
clk: tegra210: fix PLLU and PLLU_OUT1
* clk-simplify-provider.h:
clk: consoldiate the __clk_get_hw() declarations
clk: Unexport __clk_of_table
clk: Remove ifdef for COMMON_CLK in clk-provider.h
* clk-sprd:
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: sprd: Check error only for devm_regmap_init_mmio()
clk: sprd: Switch from of_iomap() to devm_ioremap_resource()
* clk-at91:
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: at91: sckc: add support for SAM9X60
dt-bindings: clk: at91: add bindings for SAM9X60's slow clock controller
clk: at91: sckc: add support to specify registers bit offsets
clk: at91: sckc: sama5d4 has no bypass support
Without this we were getting errors like:
In file included from drivers/clk/clkdev.c:22:0:
drivers/clk/clk.h:36:23: error: static declaration of '__clk_get_hw' follows non-static declaration
include/linux/clk-provider.h:808:16: note: previous declaration of '__clk_get_hw' was here
Fixes: 59fcdce425 ("clk: Remove ifdef for COMMON_CLK in clk-provider.h")
fixes: 73e0e496af ("clkdev: Always allocate a struct clk and call __clk_get() w/ CCF")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Call imx_register_uart_clocks() API to keep uart clocks enabled
when earlyprintk or earlycon is active.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some of i.MX SoCs' clock driver use platform driver model,
and they need to call imx_register_uart_clocks() API, so
imx_register_uart_clocks() API should NOT be in .init section.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation http www opensource org
licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081201.897982733@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The imx6q_obtain_fixed_clk_hw lacks an __init marker, which
leads to this otherwise harmless warning:
WARNING: vmlinux.o(.text+0x495358): Section mismatch in reference from the function imx6q_obtain_fixed_clk_hw() to the function .init.text:imx_obtain_fixed_clock_hw()
The function imx6q_obtain_fixed_clk_hw() references
the function __init imx_obtain_fixed_clock_hw().
This is often because imx6q_obtain_fixed_clk_hw lacks a __init
annotation or the annotation of imx_obtain_fixed_clock_hw is wrong.
Fixes: 992b703b5b ("clk: imx6q: Switch to clk_hw based API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some of i.MX SoCs' clock driver use platform driver model,
and they need to call imx_check_clocks() API, so
imx_check_clocks() API should NOT be in .init section.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx6sll driver to clk_hw based API.
This allows us to move closer to a clear split between
consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx7d driver to clk_hw based API. This allows us
to move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx6ul driver to clk_hw based API. This allows us
to move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx6sx driver to clk_hw based API. This allows us
to move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx6q driver to clk_hw based API.
Add imx6q_obtain_fixed_clk_hw helper to clean up the registration
of the clocks that are either found in device tree or are assigned
a fixed zero rate. This switch allows us to move closer to a clear
split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx6sl driver to clk_hw based API.
This allows us to move closer to a clear split between
consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch all the wrappers to clk_hw based API and rename them to indicate
that. Add macros for clk based legacy users. This allows us to move
closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_fixup_mux function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. a macro for clk
based legacy. This allows us to move closer to a clear split between
consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_fixup_divider function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_gate_exclusive function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to move
closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_pfd function to clk_hw based API, rename accordingly
and add a macro for clk based legacy. This allows us to move closer to
a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_hw_pllv3 function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us
to move closer to a clear split between consumer and provider clk
APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the clk_register_gate2 function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the clk_cpu clock registering function to clk_hw based API and add
a macro for clk based legacy. This allows us to move closer to a clear
split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch all the clk_busy clock registering functions to clk_hw based API.
Keep around some clk based wrappers to be used by older imx platforms.
This allows us to move closer to a clear split of consumer and provider
clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clock is registered later than these two re-parentings.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clock IMX6SX_CLK_AXI is not registered at all.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to move to clk_hw based API, imx_obtain_fixed_clock_hw
is added. The end goal here is to have all the clk providers use
the clk_hw based API.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no audio_pll2_clk registered, it should be audio_pll2_out.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 246 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
- Don't expose the SiFive clk driver on non-RISCV architectures
- Fix some bits describing clks in the imx8mm driver
- Always call clk domain code in the TI driver so non-legacy platforms
work
-----BEGIN PGP SIGNATURE-----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=gbSJ
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk driver fixes from Stephen Boyd:
- Don't expose the SiFive clk driver on non-RISCV architectures
- Fix some bits describing clks in the imx8mm driver
- Always call clk domain code in the TI driver so non-legacy platforms
work
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: clkctrl: Fix clkdm_clk handling
clk: imx: imx8mm: fix int pll clk gate
clk: sifive: restrict Kconfig scope for the FU540 PRCI driver
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MMDC_P1_IPG clock need to be on always on to make sure
the MMDC register can be accessed successfully.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This clock is used for dram operations inside TF-A and must be kept
enabled for features such as suspend/resume dram retention and busfreq
to work.
This is required for imx8mm suspend to work with NXP branch of TF-A.
There is an equivalent clk on imx8mq and it's always been marked as
critical in upstream.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since i.MX7ULP B0 chip, nic1_bus_clk's parent is changed to
from nic0_clk directly, update it accordingly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx_mmdc_mask_handshake() API instead of programming CCM
register directly in each platform to mask unused MMDC channel's
handshake.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All i.MX6 SoCs need to mask unused MMDC channel's handshake
for low power modes, this patch provides common API for masking
the MMDC channel passed from caller.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is documented in the reference manuals as GIC_CLK_ROOT.
In some out-of-tree DVFS scenarios the gic clock can end up as the only
user of sys_pll2 so if we don't define the gic clk explicitly it might
be turned off.
This applies to both 8mq and 8mm: same clk register but diffferent
parents.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has clock gate for SNVS module, add it into clock tree
for SNVS RTC driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for SNVS module, add it into clock tree
for SNVS RTC driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To Frac pll, the gate shift is 13, however to Int PLL the gate shift
is 11.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.615184352@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX8MM has clock gate for each GPIO bank, add them
into clock tree for GPIO driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Remove clk_readl() and introduce BE versions of basic clk types
* clk-doc:
clk: Drop duplicate clk_register() documentation
clk: Document and simplify clk_core_get_rate_nolock()
clk: Remove 'flags' member of struct clk_fixed_rate
clk: nxp: Drop 'flags' on fixed_rate clk macro
clk: Document __clk_mux_determine_rate()
clk: Document CLK_MUX_READ_ONLY mux flag
clk: Document deprecated things
clk: Collapse gpio clk kerneldoc
* clk-more-critical:
clk: highbank: Convert to CLK_IS_CRITICAL
* clk-meson: (21 commits)
clk: meson: axg-audio: add g12a support
clk: meson: axg-audio: don't register inputs in the onecell data
clk: meson: axg_audio: replace prefix axg by aud
dt-bindings: clk: axg-audio: add g12a support
clk: meson: meson8b: add the video decoder clock trees
clk: meson: meson8b: add the VPU clock trees
clk: meson: meson8b: add support for the GP_PLL clock on Meson8m2
clk: meson: meson8b: use a separate clock table for Meson8m2
dt-bindings: clock: meson8b: export the video decoder clocks
clk: meson-g12a: add video decoder clocks
dt-bindings: clock: meson8b: export the VPU clock
clk: meson-g12a: add PCIE PLL clocks
dt-bindings: clock: g12a-aoclk: expose CLKID_AO_CTS_OSCIN
clk: meson-pll: add reduced specific clk_ops for G12A PCIe PLL
dt-bindings: clock: meson8b: drop the "ABP" clock definition
clk: meson: g12a: add cpu clocks
dt-bindings: clk: g12a-clkc: add VDEC clock IDs
dt-bindings: clock: axg-audio: unexpose controller inputs
dt-bindings: clk: g12a-clkc: add PCIE PLL clock ID
clk: g12a-aoclk: re-export CLKID_AO_SAR_ADC_SEL clock id
...
* clk-basic-be:
clk: core: replace clk_{readl,writel} with {readl,writel}
clk: core: remove powerpc special handling
powerpc/512x: mark clocks as big endian
clk: mux: add explicit big endian support
clk: multiplier: add explicit big endian support
clk: gate: add explicit big endian support
clk: fractional-divider: add explicit big endian support
clk: divider: add explicit big endian support
The operations of pfdv2 gate_bit/valid_bit are incorrect,
they are defined as u8 for bit offset, but gate_bit is
actually assigned as mask which could be 32 bit long and
it causes overflow, and vld_bit is assigned as bit offset
based on incorrect gate_bit value, it causes incorrect
pfd clock gate status in clock tree, this patch fixes the
issue by assigning them as correct bit offset.
Fixes: 9fcb6be3b6 ("clk: imx: add pfdv2 support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/clk/imx/clk-pllv3.c: In function ‘imx_clk_pllv3’:
drivers/clk/imx/clk-pllv3.c:446:18: warning: this statement may fall through [-Wimplicit-fallthrough=]
pll->div_shift = 1;
~~~~~~~~~~~~~~~^~~
drivers/clk/imx/clk-pllv3.c:447:2: note: here
case IMX_PLLV3_USB:
^~~~
drivers/clk/imx/clk-pllv3.c:453:21: warning: this statement may fall through [-Wimplicit-fallthrough=]
pll->denom_offset = PLL_IMX7_DENOM_OFFSET;
^
drivers/clk/imx/clk-pllv3.c:454:2: note: here
case IMX_PLLV3_AV:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: b4a4cb5a04 ("clk: imx: correct i.MX7D AV PLL num/denom offset")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It's defined in imx8mq-clock.h but wasn't assigned yet. It's used as
clk_tx_esc in the nwl dsi host controller (i.MX8MQ RM, Rev. 0, 01/2018
Sect. 13.5.3.7.4).
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Keep uart clocks enabled when earlyprintk or
earlycon is active.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According reference manual, i.MX7D's audio/video PLL's
num/denom register offset are 0x20/0x30, they are different
from i.MX6's audio/video PLL, correct it by introducing new
offset variables for audio/video PLL and using runtime
assignment based on PLL type.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This looks like a copy-paste error. This string is not referenced
anywhere so it's safe to rename it.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It does not make sense to only get value from pll->base and assign
to a local variable when recalc_rate.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Remove SNVS clock from i.MX7UPL clock driver and bindings, as the
clock will be visible on M4 core only, and never be accessed by
Cortex-A cores.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvThaAAoJEFBXWFqHsHzOoR0H/0AjB+fmbMoeGEpo0pZjPFyw
RbQ/+UavX0Yy4z4LJmYw3y3n7/cLvyv8Edg/BRXCvgX6dmjHa6sOSW3rZSD7BWUp
Jg6m/NCkaq4GRFOfXrs+vzmjtEECyq5j6EV9QG8w3ZBEU733FkcQgMTsOmK9u7kF
fxUfz7PReS6ZPk276gTMwWaNOl1R6W8eaHjiK0F1LQIcZfPRcsPtFRFkriQ27m/7
MOJ5Wjpf5804qis3p8gDIc/Z+wPaf5QF0exNKL/55INjVeSwCw81TAqTpFWrkrgj
lF2DTXgBHVO9S03I5/d5CNFCYdlP7EbgRD5CoH7mWrqEiBnvUUAxhe5zlm4etno=
=4yV1
-----END PGP SIGNATURE-----
Merge tag 'clk-imx7ulp-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-imx
Pull i.MX7UPL clk changes from Shawn Guo:
- Remove SNVS clock from i.MX7UPL clock driver and bindings, as the
clock will be visible on M4 core only, and never be accessed by
Cortex-A cores
* tag 'clk-imx7ulp-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: clock: imx7ulp: remove SNVS clock
clk: imx7ulp: remove snvs clock
- A couple of patches from Jonathan Neuschäfer to improve i.MX5 clock
driver for i.MX50 support.
- Rename file clk-imx51-imx53.c to clk-imx5.c, as it covers support for
all i.MX5 series SoCs including i.MX50.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvTXlAAoJEFBXWFqHsHzO9oAH+wQtUGOJw7Yiu/UcjGQmoWRJ
0MRLknDBlVBTKSqZLVoFsm2xRyCkdHA7QB3OaCui4I40pdwoCOxDFHUOc2PTwBk2
kr0tHiiYoYXF6oZioD5tCh2zLHNuCIYy+TLzwG4jVavUCQAnQE8jzE59kiEvxBVg
9dvVxRjiIcHg0azm/oRsD+HQYwZ0ALMkLcAtbP1GGgsHeoSbaPJsYQCmj+9jDP8t
OKwgtum7DeYFlelCMF70BubA3NmAFz3uKrgh1lXRGSM5nm2aMmuNyypFIN6c7E53
ELWfXvRLfncl5uipeIc5Km5r0L+AwBQmH9aOyzd3i4Ys2z3Kp5atSEhuqbDWnDI=
=udGf
-----END PGP SIGNATURE-----
Merge tag 'clk-imx5-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-imx
Pull i.MX5 clk changes from Shawn Guo:
- A couple of patches from Jonathan Neuschäfer to improve i.MX5 clock
driver for i.MX50 support
- Rename file clk-imx51-imx53.c to clk-imx5.c, as it covers support for
all i.MX5 series SoCs including i.MX50
* tag 'clk-imx5-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx: rename clk-imx51-imx53.c to clk-imx5.c
clk: imx5: Fix i.MX50 ESDHC clock registers
clk: imx5: Fix i.MX50 mainbus clock registers
Now that clk_{readl,writel} is just an alias for {readl,writel}, we can
switch all users of clk_* to use the accessors directly and remove the
helpers.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[sboyd@kernel.org: Also convert renesas file so that this can be
compile independently]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As the driver is handling all i.MX5 series SoCs inlcuding i.MX50, rather
than just i.MX51 and i.MX53, let's rename it to clk-imx5.c.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Code which initializes the "clk_init_data.ops" checks pll->rate_table
before that field is ever assigned to so it always picks
"clk_pll1416x_min_ops".
This breaks dynamic rate rounding for features such as cpufreq.
Fix by checking pll_clk->rate_table instead, here pll_clk refers to
the constant initialization data coming from per-soc clk driver.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The MUX bits for esdhc_{a,c,d}_sel are shifted by one bit within CSCMR1,
because esdhc_b_sel (ESDHC3_CLK_SEL in the Reference Manual) is extended
by one bit.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX50 does not have a periph_apm clock. Instead, the main bus clock
(a.k.a. periph_clk) comes directly from a MUX between pll1_sw, pll2_sw,
pll3_sw, and lp_apm.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is never used and the imx_clk_hw_fixed does the same thing.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since i.MX7ULP B0 chip, the SNVS module is moved into M4
domain and its clock is also moved into PCC0 which is
contorlled by M4, Linux kernel should NOT add it into
clock tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Split LCDC into two clks on the Marvell MMP2 SoC
* clk-imx:
clk: imx8mq: add GPIO clocks to clock tree
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: imx: imx8mm: Mark init function __init
clk: imx8mq: Add the missing ARM clock
dt-bindings: imx8mq-clock: Add the missing ARM clock
clk: imx: imx8mq: Fix the rate propagation for arm pll
clk: imx8mq: Add support for the CLKO1 clock
clk: imx8mq: Fix the CLKO2 source select list
clk: imx8mq: Add missing M4 clocks
clk: imx: Add clock driver support for imx8mm
dt-bindings: imx: Add clock binding doc for imx8mm
clk: imx: Add PLLs driver for imx8mm soc
clk: imx5: add imx5_SCC2_IPG_GATE
clk: imx: scu: add set parent support
clk: imx: scu: add fallback compatible string support
clk: imx8mq: Make parent names arrays const pointers
clk: imx: Make parents const pointer in mux wrappers
clk: imx: Make parent_names const pointer in composite-8m
* clk-samsung:
clk: samsung: s3c2443: Mark expected switch fall-through
clk: samsung: exynos5: Fix kfree() of const memory on setting driver_override
clk: samsung: exynos5: Fix possible NULL pointer exception on platform_device_alloc() failure
clk: samsung: exynos5433: Add selected IMEM clocks
clk: samsung: dt-bindings: Document Exynos5433 IMEM CMU
clk: samsung: exynos5433: Fix name typo in sssx
clk: samsung: exynos5433: Fix definition of CLK_ACLK_IMEM_{200, 266} clocks
clk: samsung: dt-bindings: Add Exynos5433 IMEM CMU clock IDs
* clk-ti:
clk: clk-twl6040: Fix imprecise external abort for pdmclk
ARM: OMAP2+: hwmod: disable ick autoidling when a hwmod requires that
clk: ti: check clock type before doing autoidle ops
clk: ti: add a usecount for autoidle
clk: ti: generalize the init sequence of clk_hw_omap clocks
clk: ti: remove usage of CLK_IS_BASIC
clk: ti: add new API for checking if a provided clock is an OMAP clock
clk: ti: move clk_hw_omap list handling under generic part of the driver
* clk-uniphier-gear:
clk: uniphier: Fix update register for CPU-gear
* clk-mmp2-lcdc:
clk: mmp2: separate LCDC peripheral clk form the display clock
dt-bindings: marvell,mmp2: Add clock id for the LCDC clock
i.MX8MQ has clock gate for each GPIO bank, add them
into clock tree for GPIO driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Make the entire combination of plls to be one single clock. The parents used
for bypasses are specified each as an index in the parents list.
The determine_rate does a lookup throughout all the possible combinations
for all the divs and returns the best possible 'setup' which in turn is used
by set_rate later to set up all the divs and bypasses.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On NXP's i.MX SoCs with system controller inside, CPU frequency
scaling can ONLY be done by system controller firmware, and it
can ONLY be requested from secure mode, so Linux kernel has to
call ARM SMC to trap to ARM-Trusted-Firmware to request system
controller firmware to do CPU frequency scaling.
This patch adds i.MX system controller CPU frequency scaling support,
it reuses cpufreq-dt driver and implement the CPU frequency scaling
inside SCU clock driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It calls another __init marked function and thus causes a section
mismatch if we don't mark it this way.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the ARM clock as imx_clk_cpu type.
Will be used by cpufreq.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The arm pll bypass needs to propagate the rate upwards
in order for the cpufreq to work.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the entry for the CLKO1 clock.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The CLKO2 clock source select list is the following as per the i.MX8M
Reference Manual:
000 - 25M_REF_CLK
001 - SYSTEM_PLL2_DIV5
010 - SYSTEM_PLL1_DIV2
011 - SYSTEM_PLL2_DIV6
100 - SYSTEM_PLL3_CLK
101 - AUDIO_PLL1_CLK
110 - VIDEO_PLL1_CLK
111 - 32K_REF_CLK
However, in imx8mq_clko2_sels[] only the first four entries are correct.
Fix it by adding the missing "sys3_pll2_out" entry in order to match
the description from the manual.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Reported-by: Rogerio Pimentel <rogerio.silva@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clocks list is missing the clocks for the M4 core.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
New PLLs are introduced on i.MX8M Mini SOC.
PLL1416X is Integer PLL, PLL1443X is a Frac PLL.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds the missing clock for the SCC2 peripheral unit.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SCU clock can be used in a similar way by IMX8QXP and IMX8QM SoCs.
Make the driver support "fsl,scu-clk" fallback compatible string
to allow other SoCs to reuse the common part.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The arrays containing the mux selectors need to be of const pointer
to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The parents needs to be pointer to const pointer to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The parent_names needs to be pointer to const pointer to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: 1e3121bfe5 ("clk: imx: add imx8qxp lpcg driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The of_find_compatible_node() returns a node pointer with refcount
incremented, but there is the lack of use of the of_node_put() when
done. Add the missing of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Fixes: 1f2c5fd5f0 ("ARM: imx: add VF610 clock support")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The of_find_compatible_node() returns a node pointer with refcount
incremented, but there is the lack of use of the of_node_put() when
done. Add the missing of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Fixes: 8f6d8094b2 ("ARM: imx: add imx7d clk tree support")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The of_find_compatible_node() returns a node pointer with refcount
incremented, but there is the lack of use of the of_node_put() when
done. Add the missing of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Fixes: d551356890 ("ARM: imx: add clock driver for imx6sx")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The of_find_compatible_node() returns a node pointer with refcount
incremented, but there is the lack of use of the of_node_put() when
done. Add the missing of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Fixes: 2acd1b6f88 ("ARM: i.MX6: implement clocks using common clock framework")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SCU clock can be used in a similar way by IMX8QXP and IMX8QM SoCs.
Let's make the name of clock ID generic to allow other SoCs to reuse
the common part.
This patch only changes the clock id name and file name, so no
functional change.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX7ULP has a Cortex-A7 CPU which can run in RUN mode
or HSRUN mode, it is controlled in SMC1 module. The RUN
mode and HSRUN mode will use different clock source for
ARM, "divcore" for RUN mode and "hsrun_divcore" for HSRUN
mode, so the control bits in SMC1 module can be abstracted
as a HW clock mux, this patch adds HSRUN mode related
clocks in SCG1 module and adds "arm" clock in SMC1 module
to support RUN mode and HSRUN mode switch.
Latest clock tree in RUN mode as below:
firc 0 0 0 48000000 0 0 50000
firc_bus_clk 0 0 0 48000000 0 0 50000
hsrun_scs_sel 0 0 0 48000000 0 0 50000
hsrun_divcore 0 0 0 48000000 0 0 50000
sosc 3 3 3 24000000 0 0 50000
spll_pre_sel 1 1 1 24000000 0 0 50000
spll_pre_div 1 1 2 24000000 0 0 50000
spll 1 1 2 528000000 0 0 50000
spll_pfd0 1 1 1 500210526 0 0 50000
spll_pfd_sel 1 1 0 500210526 0 0 50000
spll_sel 1 1 0 500210526 0 0 50000
scs_sel 1 1 0 500210526 0 0 50000
divcore 1 1 0 500210526 0 0 50000
arm 1 1 0 500210526 0 0 50000
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Low-Power Clock Gate (LPCG) modules contain a local programming
model to control the clock gates for the peripherals. An LPCG module
is used to locally gate the clocks for the associated peripheral.
And they're bedind the SCU clock.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add imx8qxp clk driver which is based on SCU firmware clock service.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Move the makefile rule higher in the file]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove the dependency between the i.MX8MQ CCM clock driver
and the CONFIG_SOC_IMX8MQ and use CONFIG_CLK_IMX8MQ instead.
CONFIG_CLK_IMX8MQ depends on ARCH_MXC && ARM64.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add SCU clock common part which will be used by client clock drivers.
SCU clocks are totally different from the legacy clocks (No much
legacy things can be reused), it's using a firmware interface now based
on SCU protocol. So a new configuration option CONFIG_MXC_CLK_SCU is added.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Mark ccm_ipc_handle static]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The patch introduces CONFIG_MXC_CLK option for legacy MMIO clocks,
this is required to compile legacy MMIO clock conditionally when adding
SCU based clocks for MX8 platforms later.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ENET PLL is different from the other i.MX6 PLLs, as it has
multiple outputs with different post-dividers, which are all
bypassed if the single bypass bit is activated. The hardware setup
looks something like this:
_
refclk-o---PLL---o----DIV1-----| \
| | |M |----OUT1
o-----------------------|_/
| | _
| o----DIV2-----| \
| | |M |----OUT2
o-----------------------|_/
| | _
| `----DIV3-----| \
| |M |----OUT3
`-----------------------|_/
The bypass bit not only bypasses the PLL, but also the attached
post-dividers. This would be reasonbly straight forward to model
with a single output, or with different bypass bits for each output,
but sadly the HW guys decided that it would be good to actuate all
3 muxes with a single bit.
So the need to have the PLL bypassed for one of the outputs always
affects 2 other (in our model) independent branches of the clock
tree.
This means the decision to bypass this PLL is a system wide design
choice and should not be changed on-the-fly, so we can treat any
bapass configuration as static. As such we can just register the
post-dividiers with a ratio that reflects the bypass status, which
allows us to bypass the PLL without breaking our abstraction model
and with it DT stability.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When specifying external clock inputs to the CCM the current code
requires the clocks to be in a "clocks" child node of the DT root.
This is not really conformant with DT best practices.
To avoid the need to deviate from those best practices, allow the
clock inputs to be specified via standard clock handles. This is
in line with how drivers of the later CCM driver revisions on
newer i.MX SoCs handle this.
As we can't retroactively change the DT binding, allow this as an
option with a fallback to the old way of how this has been handled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The exclusive gates may be set up in the wrong way by software running
before the clock driver comes up. In that case the exclusive setup is
locked in its initial state, as the complementary function can't be
activated without disabling the initial setup first.
To avoid this lock situation, reset the exclusive gates to the off
state and allow the kernel to provide the proper setup.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On i.MX6QP/i.MX6Q/i.MX6DL, there are DCIC1/DCIC2 clocks
gate in CCM_CCGR0 register, add them into clock tree for
clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Same as other i.MX6 SoCs, ensure unused MMDC channel's
handshake is bypassed, this is to make sure no request
signal will be generated when periphe_clk_sel is changed
or SRC warm reset is triggered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The initialization of ret is redundant as it is being re-assigned to
the return value from the call to imx8m_clk_composite_compute_dividers.
Clean this up by removing the initialization.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX7ULP Clock functions are under joint control of the System
Clock Generation (SCG) modules, Peripheral Clock Control (PCC)
modules, and Core Mode Controller (CMC)1 blocks
The clocking scheme provides clear separation between M4 domain
and A7 domain. Except for a few clock sources shared between two
domains, such as the System Oscillator clock, the Slow IRC (SIRC),
and and the Fast IRC clock (FIRCLK), clock sources and clock
management are separated and contained within each domain.
M4 clock management consists of SCG0, PCC0, PCC1, and CMC0 modules.
A7 clock management consists of SCG1, PCC2, PCC3, and CMC1 modules.
This driver only adds clock support in A7 domain.
Note that most clocks required to be operated when gated, e.g. pll,
pfd, pcc. And more special cases that scs/ddr/nic mux selecting
different clock source requires that clock to be enabled first,
then we need set CLK_OPS_PARENT_ENABLE flag for them properly.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock providers are recommended to use the new struct clk_hw based API,
so implement IMX clk_hw based provider helpers functions to the new
approach.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As the commit 2893c37946 ("clk: make strings in parent name arrays
const"), let's make the parent strings const, otherwise we may meet
the following warning when compiling:
drivers/clk/imx/clk-imx7ulp.c: In function 'imx7ulp_clocks_init':
drivers/clk/imx/clk-imx7ulp.c:73:35: warning: passing argument 5 of
'imx_clk_mux_flags' discards 'const' qualifier from pointer target type
clks[IMX7ULP_CLK_APLL_PRE_SEL] = imx_clk_mux_flags("apll_pre_sel", base + 0x508, 0,
1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
^
In file included from drivers/clk/imx/clk-imx7ulp.c:23:0:
drivers/clk/imx/clk.h:200:27: note: expected 'const char **' but argument is
of type 'const char * const*'
...
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The imx composite clk is designed for Peripheral Clock Control (PCC)
module observed in IMX ULP SoC series.
NOTE pcc can only be operated when clk is gated.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The pfdv2 is designed for PLL Fractional Divide (PFD) observed in System
Clock Generation (SCG) module in IMX ULP SoC series. e.g. i.MX7ULP.
NOTE pfdv2 can only be operated when clk is gated.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pllv4 is designed for System Clock Generation (SCG) module observed
in IMX ULP SoC series. e.g. i.MX7ULP.
The SCG modules generates clock used to derive processor, system,
peripheral bus and external memory interface clocks while this patch
intends to support the PLL part.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For dividers with zero indicating clock is disabled, instead of giving a
warning each time like "clkx: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not
set" in exist code, we'd like to introduce enable/disable function for it.
e.g.
000b - Clock disabled
001b - Divide by 1
010b - Divide by 2
...
Set rate when the clk is disabled will cache the rate request and only
when the clk is enabled will the driver actually program the hardware to
have the requested divider value. Similarly, when the clk is disabled we'll
write a 0 there, but when the clk is enabled we'll restore whatever rate
(divider) was chosen last.
It does mean that recalc rate will be sort of odd, because when the clk is
off it will return 0, and when the clk is on it will return the right rate.
So to make things work, we'll need to return the cached rate in recalc rate
when the clk is off and read the hardware when the clk is on.
NOTE for the default off divider, the recalc rate will still return 0 as
there's still no proper preset rate. Enable such divider will give user
a reminder error message.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The SCCG is a new PLL type introduced on i.MX8.
The description of this SCCG clock can be found here:
https://www.nxp.com/docs/en/reference-manual/IMX8MDQLQRM.pdf#page=834
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is a new fractional clock type introduced on i.MX8.
The description of this fractional clock can be found here:
https://www.nxp.com/docs/en/reference-manual/IMX8MDQLQRM.pdf#page=834
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add driver for the Clock Control Module found on i.MX8MQ.
Signed-off-by: Anson Huang <anson.huang@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since a lot of clocks on imx8m are formed by a mux, gate, predivider and
divider, the idea here is to combine all of those into one composite clock,
but we need to deal with both predivider and divider at the same time and
therefore we add the imx8m_clk_composite_divider_ops and register
the composite clock with those.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are clock assignments in all i.MX7D dtb files for UART1,
below is the example in imx7d-sdb.dts, so setting UART1 clock
in clock driver is NOT necessary, actually, module clocks setting
should be done in module driver.
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
status = "okay";
};
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6Q has MMDC0 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SL has MMDC0 and MMDC1 ipg clock in CCM CCGR, add them into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SLL has MMDC1 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SX has MMDC1 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6UL has MMDC1 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX7D uses virtual cpu clock of "arm" clock to be child clock
of "arm_a7_root_clk" and it is with CLK_IS_CRITICAL flag set, so
no need to add CLK_IS_CRITICAL flag for keeping "arm_a7_root_clk"
use count correct, latest clock tree is as below in clk_summary:
pll_arm_main 1 1 0 792000000 0
pll_arm_main_bypass 1 1 0 792000000 0
pll_arm_main_clk 1 1 0 792000000 0
arm_a7_src 1 1 0 792000000 0
arm_a7_cg 1 1 0 792000000 0
arm_a7_div 1 1 0 792000000 0
arm_a7_root_clk 1 1 0 792000000 0
arm 1 1 0 792000000
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add CLK_IS_CRITICAL flag for cpu clock type to
make cpu clock use count correct, as cpu clock
should be always critical.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On i.MX7D, IMX7D_NAND_USDHC_BUS_ROOT_CLK is NOT necessary
for system, and IMX7D_AHB_CHANNEL_ROOT_CLK is NOT existing
at all, remove them from clks_init_on array.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-imx-critical:
: - Convert to CLK_IS_CRITICAL for i.MX51/53 driver
clk: imx51-imx53: Include sizes.h to silence compile errors
clk: imx51-imx53: Annotate critical clocks as CLK_IS_CRITICAL
* clk-tegra-bpmp:
: - Fix Tegra BPMP driver oops when some xlating a NULL clk
clk: tegra: bpmp: Don't crash when a clock fails to register
* clk-tegra-124:
: - Proper default configuration for vic03 and vde clks on Tegra124
clk: tegra: Make vde a child of pll_c3
clk: tegra: Make vic03 a child of pll_c3
* clk-tegra-critical:
: - Mark Tegra memory controller clks as critical
clk: tegra: Mark Memory Controller clock as critical
* clk-tegra-emc-oob:
: - Fix array bounds clamp in Tegra's emc determine_rate() op
clk: tegra: emc: Avoid out-of-bounds bug
of_find_compatible_node() is returning a device node with refcount
incremented and must be explicitly decremented after the last use
which is right after the us in of_iomap() here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 4a5f720b65 ("clk: imx: add clock driver for imx6sll")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
of_find_compatible_node() is returning a device node with refcount
incremented and must be explicitly decremented after the last use
which is right after the us in of_iomap() here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 787b4271a6 ("clk: imx: add imx6ul clk tree support")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SX has a 16KB always-on ocram bank called
ocram_s, and its clock gate in CCM CCGR1 CG14
needs to be enabled before access, add it to
clock tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This driver uses sizes.h, but relies on it being implicitly included
somewhere else breaking random direct compilation of the file. Include
sizes.h so we can build it those configurations too for better compile
coverage.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Instead of explicitly enabling critical clocks via clk_prepare_enable(),
let's use the standard CLK_IS_CRITICAL flag instead, which makes the code
a bit shorter.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to Reference Manual Rev.0, 06/2017, there are GPIO LPCGs
defined in CCM CCGRs, add them into clock tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
q/dl datasheets list the 5th selection value for ck01_sel as
video_27M_clk_root.
By replacing the dummy value we then can set IMX6QDL_CLK_VIDEO_27M
as parent for IMX6QDL_CLK_CKO1_SEL.
Signed-off-by: Philipp Puschmann <pp@emlix.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6UL has GPIO clock gates in CCM CCGR,
add them into clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
IPG clock has no clock gate and its parent AHB clock
is busy divider type, so no need to add CLK_IS_CRITICAL
flag for IPG clock.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
IPG clock has no clock gate and its parent AHB clock
is busy divider type, so no need to add CLK_IS_CRITICAL
flag for IPG clock.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
general cleanups, but nothing too major. The majority of the diff goes to
two SoCs, Actions Semi and Qualcomm. A brand new driver is introduced for
Actions Semi so it takes up some lines to add all the different types, and
the Qualcomm diff is there because we add support for two SoCs and it's quite
a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic platforms. And
then the long tail of driver updates for various fixes and stuff follows
after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock
-----BEGIN PGP SIGNATURE-----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=KK/v
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time we have a good set of changes to the core framework that do
some general cleanups, but nothing too major. The majority of the diff
goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
introduced for Actions Semi so it takes up some lines to add all the
different types, and the Qualcomm diff is there because we add support
for two SoCs and it's quite a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic
platforms. And then the long tail of driver updates for various fixes
and stuff follows after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
clk: qcom: Export clk_fabia_pll_configure()
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
clk-si544: Properly round requested frequency to nearest match
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
clk: use match_string() helper
clk: bcm2835: use match_string() helper
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
clk: imx6: add EPIT clock support
clk: mvebu: use correct bit for 98DX3236 NAND
...
* clk-imx7d:
clk: imx7d: reset parent for mipi csi root
clk: imx7d: fix mipi dphy div parent
* clk-hisi-stub:
clk/driver/hisi: Consolidate the Kconfig for the CLOCK_STUB
* clk-mvebu:
clk: mvebu: use correct bit for 98DX3236 NAND
* clk-imx6-epit:
clk: imx6: add EPIT clock support
* clk-debugfs-simple:
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
Add EPIT clock support to the i.MX6Q clocking infrastructure.
Signed-off-by: Colin Didier <colin.didier@devialet.com>
Signed-off-by: Clément Peron <clement.peron@devialet.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
To guarantee that we do not get Overflow in image FIFO the outer bandwidth has
to be faster than inputer bandwidth. For that it must be possible to set a
faster frequency clock. So set new parent to sys_pfd3 clock for the mipi csi
block.
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Correct enet clock gates as below:
CCGR6: IMX7D_ENET_AXI_ROOT_CLK (enet1 and enet2 bus clocks)
CCGR112: IMX7D_ENET1_TIME_ROOT_CLK, IMX7D_ENET1_IPG_ROOT_CLK
CCGR113: IMX7D_ENET2_TIME_ROOT_CLK, IMX7D_ENET2_IPG_ROOT_CLK
Just rename unused IMX7D_ENETx_REF_ROOT_CLK for
IMX7D_ENETx_IPG_ROOT_CLK instead of adding new clocks.
Based on Andy Duan's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
IMX7D_ENET_PHY_REF_ROOT_DIV supplies clock for PHY directly,
there is no clock gate after it, rename it to
IMX7D_ENET_PHY_REF_ROOT_CLK to avoid device tree change.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
IMX6SL_CLK_OCRAM_PODF is a busy divider, its name in
CCM_CDHIPR register of Reference Manual CCM chapter
is axi_podf_busy, correct its clock type.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Disable those unnecessary clocks during kernel boot up to save power,
those modules clock should be managed by modules driver in runtime.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On i.MX6 ULL using PLL3 seems to cause a freeze when setting
the parent to IMX6UL_CLK_PLL3_USB_OTG. This only seems to appear
since commit 6f9575e556 ("clk: imx: Add CLK_IS_CRITICAL flag
for busy divider and busy mux"), probably because the clock is
now forced to be on.
Fixes: 6f9575e55632("clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SX has lvds2 (analog clock2), an I/O clock like lvds1.
And this lvds2, along with lvds1, can be used to provide
external clock source to the internal pll, such as pll4_audio
and pll5_video.
This patch mainly adds the lvds2 to the clock tree and fix its
relationship with pll accordingly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to the data sheet the 3rd choice is the bypass clock
of pll2. This should not have any effect in practice as this
selection is not used currently.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
for the TI Davinci family of SoCs. So far those clks have been supported
with a custom implementation of the clk API in the arch port instead of in
the CCF. With this driver merged we're one step closer to having a single
clk API implementation.
The other large diff is from the Amlogic clk driver that underwent some
major surgery to use regmap. Beyond that, the biggest hitter is Samsung
which needed some reworks to properly handle clk provider power domains
and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some cleanups
and small fixes for some of the more esoteric features. And the usual
set of driver non-critical fixes, cleanups, and minor additions are here as
well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC
-----BEGIN PGP SIGNATURE-----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=ys4O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The large diff this time around is from the addition of a new clk
driver for the TI Davinci family of SoCs. So far those clks have been
supported with a custom implementation of the clk API in the arch port
instead of in the CCF. With this driver merged we're one step closer
to having a single clk API implementation.
The other large diff is from the Amlogic clk driver that underwent
some major surgery to use regmap. Beyond that, the biggest hitter is
Samsung which needed some reworks to properly handle clk provider
power domains and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some
cleanups and small fixes for some of the more esoteric features. And
the usual set of driver non-critical fixes, cleanups, and minor
additions are here as well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
clk: davinci: add a reset lookup table for psc0
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
clk: cs2000: set pm_ops in hibernate-compatible way
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
clk: ti: fix flag space conflict with clkctrl clocks
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: Add driver for the si544 clock generator chip
clk: davinci: Remove redundant dev_err calls
clk: uniphier: add ethernet clock control support for PXs3
...
Add clk driver support for imx6sll.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add new gate/gate2 wrapper function to register clocks with optional flags.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The busy divider and busy mux is actually used by the system critical clocks,
so add 'CLK_IS_CRITICAL' to clocks registered with these two type.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For init on clocks we should move it at the first place in imx7d_clocks_init()
before any clock operations, else the clock operation may fail in case the clock
is still not on.
Acked-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Design team change the ahb's clk parent options but
did NOT update the DOC accordingly in time, so the
AHB/IPG's clk rate in clk tree is incorrect, AHB is
67.5MHz and IPG is 33.75MHz, but using scope to
monitor them, they are actually 135MHz and 67.5MHz,
update the clk parent option to make clk tree info
correct.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
DRAM PLL is a audio/video type PLL, need to correct
it to get correct ops of PLL.
There is a test_div placed before DRAM PLL's gate, so
add this test div clk.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add USB clock information, the pll_usb_main_clk is USB_PLL at CCM
which is the output of USBOTG2 PHY.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is the usual set of changes for device trees, with over 700
non-merged changesets. There is an ongoing set of dtc warning fixes and
the usual bugfixes, cleanups and added device support.
The most interesting bit as usual is support for new machines listed
below:
- The Allwinner H6 makes its debut with the Pine-H64 board, and we get
two new machines based on its older siblings: the H5 based OrangePi
Zero+ and the A64 based Teres-I Laptop from Olimex. On the 32-bit side,
we add The Olimex som204 based on Allwinner A20, and the Banana Pi M2
Zero development board (based on H2).
- NVIDIA adds support for Tegra194 aka "Xavier", plus their p2972
development board and p2888 CPU module.
- The Nuvoton npcm750 is a BMC that was newly added, for now we only
support running on the evaluation board.
- STmicroelectronics stm32 gains support for the stm32mp157c and two
evaluation boards.
- The Toradex Colibri board family grows a few members based on the
i.MX6ULL variant.
- The Advantec DMS-BA16 is a Qseven module using the NXP i.MX6
family of chips.
- The Phytec phyBOARD Mira is a family of industrial boards based on
i.MX6. For now, four models get added.
- TI am335x based PDU-001 is an industrial embedded machine used for
traffic monitoring
- The Aspeed platform now supports running on the BMC on the Qualcomm
Centriq 2400 server
- Samsung Exynos4 based Galaxy S3 is a family of mobile phones Qualcomm
msm8974 based Galaxy S5 is a rather different phone made by the same
company.
- The Xilinx Zynq and ZynqMP platforms now gained a lot of dts file
for the various boards made by Xilinx themselves, as well as the
Digilent Zybo Z7.
- The ARM Versatile family now supports the "IB2" interface board.
- The Renesas H2 based "Stout" and the H3 based Salvator-X are more
evaluation boards named after a kind of beer, as most of them are.
The r8a77980 (V3H) based "Condor" apparently doesn't follow that
tradition. ;-)
- ROC-RK3328-CC is a simple developement board from the Libre Computer
Project, based on the Rockchips RK3328 SoC
- Haiku is another development board plus Qseven module based on Rockchips
RK3368 and made by Theobroma Systems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7rHo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is the usual set of changes for device trees, with over 700
non-merged changesets. There is an ongoing set of dtc warning fixes
and the usual bugfixes, cleanups and added device support.
The most interesting bit as usual is support for new machines listed
below:
- The Allwinner H6 makes its debut with the Pine-H64 board, and we
get two new machines based on its older siblings: the H5 based
OrangePi Zero+ and the A64 based Teres-I Laptop from Olimex. On the
32-bit side, we add The Olimex som204 based on Allwinner A20, and
the Banana Pi M2 Zero development board (based on H2).
- NVIDIA adds support for Tegra194 aka "Xavier", plus their p2972
development board and p2888 CPU module.
- The Nuvoton npcm750 is a BMC that was newly added, for now we only
support running on the evaluation board.
- STmicroelectronics stm32 gains support for the stm32mp157c and two
evaluation boards.
- The Toradex Colibri board family grows a few members based on the
i.MX6ULL variant.
- The Advantec DMS-BA16 is a Qseven module using the NXP i.MX6 family
of chips.
- The Phytec phyBOARD Mira is a family of industrial boards based on
i.MX6. For now, four models get added.
- TI am335x based PDU-001 is an industrial embedded machine used for
traffic monitoring
- The Aspeed platform now supports running on the BMC on the Qualcomm
Centriq 2400 server
- Samsung Exynos4 based Galaxy S3 is a family of mobile phones
Qualcomm msm8974 based Galaxy S5 is a rather different phone made
by the same company.
- The Xilinx Zynq and ZynqMP platforms now gained a lot of dts file
for the various boards made by Xilinx themselves, as well as the
Digilent Zybo Z7.
- The ARM Versatile family now supports the "IB2" interface board.
- The Renesas H2 based "Stout" and the H3 based Salvator-X are more
evaluation boards named after a kind of beer, as most of them are.
The r8a77980 (V3H) based "Condor" apparently doesn't follow that
tradition. ;-)
- ROC-RK3328-CC is a simple developement board from the Libre
Computer Project, based on the Rockchips RK3328 SoC
- Haiku is another development board plus Qseven module based on
Rockchips RK3368 and made by Theobroma Systems"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (701 commits)
arm: dts: modify Nuvoton NPCM7xx device tree structure
arm: dts: modify Makefile NPCM750 configuration name
arm: dts: modify clock binding in NPCM750 device tree
arm: dts: modify timer register size in NPCM750 device tree
arm: dts: modify UART compatible name in NPCM750 device tree
arm: dts: add watchdog device to NPCM750 device tree
arm64: dts: uniphier: add ethernet node for PXs3
ARM: dts: uniphier: add pinctrl groups of ethernet for second instance
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for board using GPL-2.0+
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0+/MIT
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0
arm: dts: armada-385-turris-omnia: use SPDX-License-Identifier
arm: dts: armada-385-db-ap: use SPDX-License-Identifier
arm: dts: armada-388-rd: use SPDX-License-Identifier
arm: dts: armada-xp-db-xc3-24g4xg: use SPDX-License-Identifier
arm: dts: armada-xp-db-dxbc2: use SPDX-License-Identifier
arm: dts: armada-370-db: use SPDX-License-Identifier
arm: dts: armada-*.dts: use SPDX-License-Identifier for most of the Armada based board
arm: dts: armada-xp-98dx: use SPDX-License-Identifier for prestara 98d SoCs
arm: dts: armada-*.dtsi: use SPDX-License-Identifier for most of the Armada SoCs
...
Forward the errors returned by __clk_pllv2_set_rate() in the recalc rate
function, to avoid using uninitialized values for the rate calculation.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- A correction on i.MX6SX CKO clock mux options.
- A fix on i.MX7D Video PLL clock tree to include the missing dividers.
- Update i.MX6UL/ULL clock driver to add epdc_podf instead of sim_podf
clock for i.MX6ULL.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJapy5hAAoJEFBXWFqHsHzOzuIIAKtLJDt8GVHdR/NHmPVvP2I1
CL0UJVaPdef4hCbV1fKdv0gRdd28rlZsKwJLvOdiRnp826sTGfbKEJF9qX3Uolt9
33RXsly35V16fzu0UhrhbcNFsjrUHeNqG50OUMEGjYtYgM/G0qkSQryl3UENS5tt
KVuYzoR45XdCaoZaLNfSwEgYPvMh/3Qbb0hm7rMVrbmVnXAKAam+2vlTqo2rZymR
Eo+zmomTIPCnbijIguq+HQcIpuhAJNpFvad2hhyiZpk76FkHC2pTtJ4b8MTSNg+1
ogn1TTcUkibkPYt26SqexCWn/7kvuYqzEtsQ2RvoaBBAOiR0zNktWMXBc621aE0=
=KJta
-----END PGP SIGNATURE-----
Merge tag 'clk-imx-4.17-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-imx
Pull i.MX clock misc updates from Shawn Guo:
- A correction on i.MX6SX CKO clock mux options.
- A fix on i.MX7D Video PLL clock tree to include the missing dividers.
- Update i.MX6UL/ULL clock driver to add epdc_podf instead of sim_podf
clock for i.MX6ULL.
* tag 'clk-imx-4.17-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx6ull: Add epdc_podf instead of sim_podf
clk: imx: imx7d: correct video pll clock tree
clk: imx: imx6sx: update cko mux options
This is one of the differences between 6ul and 6ull: imx6ull has no sim
but has epdc and this clock is redefined on the same bit.
This can be verified in the Reference Manuals.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a test divider and post divider in video PLL,
test divider is placed before post divider, all clocks
that can select parent from video PLL should be from
post divider, NOT from pll_video_main, below are
clock tree dump before and after this patch:
Before:
pll_video_main
pll_video_main_bypass
pll_video_main_clk
lcdif_pixel_src
lcdif_pixel_cg
lcdif_pixel_pre_div
lcdif_pixel_post_div
lcdif_pixel_root_clk
After:
pll_video_main
pll_video_main_bypass
pll_video_main_clk
pll_video_test_div
pll_video_post_div
lcdif_pixel_src
lcdif_pixel_cg
lcdif_pixel_pre_div
lcdif_pixel_post_div
lcdif_pixel_root_clk
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the i.MX7D Reference Manual, the Keypad Port module
(KPP) requires this clock gate to be enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the i.MX7D Reference Manual,
SNVS block has a clock gate, accessing SNVS block
would need this clock gate to be enabled, add it
into clock tree so that SNVS module driver can
operate this clock gate.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX51 only has 3 UARTs and no CCGR7 register. In place of the CCGR7
register on i.MX50/i.MX53 that contains the ipg and per clock gates
for UARTs 4 and 5, on i.MX51 there is the CMEOR register.
Without this patch, the code disabling the UART clocks would also clear
the mod_en_ov_vpu bit in the CMEOR register, among others, which causes
register accesses to the VPU to lock up the system.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
large change that introduces runtime PM support to the clk framework. Now we
properly call runtime PM operations on the device providing a clk when the clk
is in use. This helps on SoCs where the clks provided by a device need
something to be powered on before using the clks, like power domains or
regulators. It also helps power those things down when clks aren't in use. The
other core change is a devm API addition for clk providers so we can get rid of
a bunch of clk driver remove functions that are just doing
of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and smattering
of non-critical fixes to existing drivers. The biggest diff is support for
Mediatek MT2712 and MT7622 SoCs, but those patches really just add a bunch
of data.
By the way, we're trying something new here where we build the tree up with
topic branches. We plan to work this into our workflow so that we don't step
on each other's toes, and so the fixes branch can be merged on an as-needed
basis.
Core:
- Runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- Runtime PM support for Samsung exynos5433/exynos4412 providers
- Removal of clkdev aliases on Samsung SoCs
- Convert clk-gpio to use gpio descriptors
- Various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- Sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- Support for the second display unit clock on Renesas RZ/G1E
- Suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- New clock ids for Rockchip rk3188 and rk3368 SoCs
- Various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hC7z
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have two changes to the core framework this time around.
The first being a large change that introduces runtime PM support to
the clk framework. Now we properly call runtime PM operations on the
device providing a clk when the clk is in use. This helps on SoCs
where the clks provided by a device need something to be powered on
before using the clks, like power domains or regulators. It also helps
power those things down when clks aren't in use.
The other core change is a devm API addition for clk providers so we
can get rid of a bunch of clk driver remove functions that are just
doing of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and
smattering of non-critical fixes to existing drivers. The biggest diff
is support for Mediatek MT2712 and MT7622 SoCs, but those patches
really just add a bunch of data.
By the way, we're trying something new here where we build the tree up
with topic branches. We plan to work this into our workflow so that we
don't step on each other's toes, and so the fixes branch can be merged
on an as-needed basis.
Summary:
Core:
- runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- runtime PM support for Samsung exynos5433/exynos4412 providers
- removal of clkdev aliases on Samsung SoCs
- convert clk-gpio to use gpio descriptors
- various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- support for the second display unit clock on Renesas RZ/G1E
- suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- new clock ids for Rockchip rk3188 and rk3368 SoCs
- various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: stm32h7: fix test of clock config
clk: pxa: fix building on older compilers
clk: sunxi-ng: a83t: Fix i2c buses bits
clk: ti: dra7-atl-clock: fix child-node lookups
clk: qcom: common: fix legacy board-clock registration
clk: uniphier: fix DAPLL2 clock rate of Pro5
clk: uniphier: fix parent of miodmac clock data
clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
clk: hi3660: fix incorrect uart3 clock freqency
clk: kona-setup: Delete error messages for failed memory allocations
ARC: clk: fix spelling mistake: "configurarion" -> "configuration"
clk: cdce925: remove redundant check for non-null parent_name
clk: versatile: Improve sizeof() usage
clk: versatile: Delete error messages for failed memory allocations
clk: ux500: Improve sizeof() usage
clk: ux500: Delete error messages for failed memory allocations
clk: spear: Delete error messages for failed memory allocations
clk: ti: Delete error messages for failed memory allocations
clk: mmp: Adjust checks for NULL pointers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IMX7d does not have an M0 Core and this particular
clock doesn't seem connected to anything else.
Remove this entry from the CCM driver.
Signed-off-by: Adriana Reus <adriana.reus@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
