In the i.MX8MP PCIe design, the PCIe PHY REF clock comes from external
OSC or internal system PLL. It is configured in the IOMUX_GPR14 register
directly, and can't be contolled by CCM at all.
Remove the PCIE PHY clock from clock driver to clean up codes.
There is only one PCIe in i.MX8MP, remove the none exist second PCIe
related clocks.
Remove the none exsits clocks IDs together.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Most if not all i.MX SoC's call a function which enables all UARTS.
This is a problem for users who need to re-parent the clock source,
because any attempt to change the parent results in an busy error
due to the fact that the clocks have been enabled already.
clk: failed to reparent uart1 to sys_pll1_80m: -16
Instead of pre-initializing all UARTS, scan the device tree to see
which UART clocks are associated to stdout, and only enable those
UART clocks if it's needed early. This will move initialization of
the remaining clocks until after the parenting of the clocks.
When the clocks are shutdown, this mechanism will also disable any
clocks that were pre-initialized.
Fixes: 9461f7b33d ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
clk drivers that dominate the diffstat because we add support for six SoCs from
that particular vendor. The other big change is the removal of various clk
drivers that are no longer used now that the kernel is dropping support for
those SoCs. Beyond that there's the usual non-critical fixes for existing
drivers and a good number of patches from Lee Jones that cleanup a bunch of W=1
enabled builds.
Removed Drivers:
- Remove efm32 clk driver
- Remove tango4 clk driver
- Remove zte zx clk driver
- Remove sirf prima2/atlast clk drivers
- Remove u300 clk driver
New Drivers:
- PLL support on MStar/SigmaStar ARMv7 SoCs
- CPU clks for Qualcomm SDX55
- GCC and RPMh clks for Qualcomm SC8180x and SC7280 SoCs
- GCC clks for Qualcomm SM8350
- GPU clks for Qualcomm SDM660/SDM630
Updates:
- Video clk fixups on Qualcomm SM8250
- Improvements for multimedia clks on Qualcomm MSM8998
- Fix many warnings with W=1 enabled builds under drivers/clk/
- Support crystal load capacitance for Versaclock VC5
- Add a "skip recall" DT binding for Silicon Labs' si570 to avoid glitches at boot
- Convert Xilinx VCU clk driver to a proper clk provider driver
- Expose Xilinx ZynqMP clk driver to more platforms
- Amlogic pll driver fixup
- Amlogic meson8b clock controller dt support clean up
- Remove mipi clk from the Amlogic axg clock controller
- New Rockchip rk3368 clock ids related to camera input
- Use pr_notice() instead of pr_warn() on i.MX6Q pre-boot ldb_di_clk reparenting
- A series from Liu Ying that adds some SCU clocks support for i.MX8qxp
DC0/MIPI-LVDS subsystems
- A series from Lucas Stach that adds PLL monitor clocks for i.MX8MQ, and
clkout1/2 support for i.MX8MM/MN
- Add I2c and Ethernet (RAVB) clocks on Renesas R-Car V3U
- Add timer (TMU) clocks on most Renesas R-Car Gen3 SoCs
- Add video-related (FCPVD/VSPD/VSPX), watchdog (RWDT), serial
(HSCIF), pincontrol/GPIO (PFC/GPIO), SPI (MSIOF), SDHI, and DMA
(SYS-DMAC) clocks on Renesas R-Car V3U
- Add support for the USB 2.0 clock selector on Renesas RZ/G2 SoCs
- Allwinner H616 SoC clk support
-----BEGIN PGP SIGNATURE-----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=dDCt
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This is all driver updates, the majority of which is a bunch of new
Qualcomm clk drivers that dominate the diffstat because we add support
for six SoCs from that particular vendor.
The other big change is the removal of various clk drivers that are no
longer used now that the kernel is dropping support for those SoCs.
Beyond that there's the usual non-critical fixes for existing drivers
and a good number of patches from Lee Jones that cleanup a bunch of
W=1 enabled builds.
Removed Drivers:
- Remove efm32 clk driver
- Remove tango4 clk driver
- Remove zte zx clk driver
- Remove sirf prima2/atlast clk drivers
- Remove u300 clk driver
New Drivers:
- PLL support on MStar/SigmaStar ARMv7 SoCs
- CPU clks for Qualcomm SDX55
- GCC and RPMh clks for Qualcomm SC8180x and SC7280 SoCs
- GCC clks for Qualcomm SM8350
- GPU clks for Qualcomm SDM660/SDM630
Updates:
- Video clk fixups on Qualcomm SM8250
- Improvements for multimedia clks on Qualcomm MSM8998
- Fix many warnings with W=1 enabled builds under drivers/clk/
- Support crystal load capacitance for Versaclock VC5
- Add a "skip recall" DT binding for Silicon Labs' si570 to avoid
glitches at boot
- Convert Xilinx VCU clk driver to a proper clk provider driver
- Expose Xilinx ZynqMP clk driver to more platforms
- Amlogic pll driver fixup
- Amlogic meson8b clock controller dt support clean up
- Remove mipi clk from the Amlogic axg clock controller
- New Rockchip rk3368 clock ids related to camera input
- Use pr_notice() instead of pr_warn() on i.MX6Q pre-boot ldb_di_clk
reparenting
- A series from Liu Ying that adds some SCU clocks support for
i.MX8qxp DC0/MIPI-LVDS subsystems
- A series from Lucas Stach that adds PLL monitor clocks for i.MX8MQ,
and clkout1/2 support for i.MX8MM/MN
- Add I2c and Ethernet (RAVB) clocks on Renesas R-Car V3U
- Add timer (TMU) clocks on most Renesas R-Car Gen3 SoCs
- Add video-related (FCPVD/VSPD/VSPX), watchdog (RWDT), serial
(HSCIF), pincontrol/GPIO (PFC/GPIO), SPI (MSIOF), SDHI, and DMA
(SYS-DMAC) clocks on Renesas R-Car V3U
- Add support for the USB 2.0 clock selector on Renesas RZ/G2 SoCs
- Allwinner H616 SoC clk support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (171 commits)
clk: mstar: msc313-mpll: Fix format specifier
clk: mstar: Allow MStar clk drivers to be compile tested
clk: qoriq: use macros to generate pll_mask
clk: qcom: Add Global Clock controller (GCC) driver for SC7280
dt-bindings: clock: Add SC7280 GCC clock binding
clk: qcom: rpmh: Add support for RPMH clocks on SC7280
dt-bindings: clock: Add RPMHCC bindings for SC7280
clk: qcom: gcc-sm8350: add gdsc
dt-bindings: clock: Add QCOM SDM630 and SDM660 graphics clock bindings
clk: qcom: Add SDM660 GPU Clock Controller (GPUCC) driver
clk: qcom: mmcc-msm8996: Migrate gfx3d clock to clk_rcg2_gfx3d
clk: qcom: rcg2: Stop hardcoding gfx3d pingpong parent numbers
dt-bindings: clock: Add support for the SDM630 and SDM660 mmcc
clk: qcom: Add SDM660 Multimedia Clock Controller (MMCC) driver
clk: qcom: gcc-sdm660: Mark GPU CFG AHB clock as critical
clk: qcom: gcc-sdm660: Mark MMSS NoC CFG AHB clock as critical
clk: qcom: gpucc-msm8998: Allow fabia gpupll0 rate setting
clk: qcom: gpucc-msm8998: Add resets, cxc, fix flags on gpu_gx_gdsc
clk: qcom: gdsc: Implement NO_RET_PERIPH flag
clk: mstar: MStar/SigmaStar MPLL driver
...
Fixes the following W=1 kernel build warning(s):
drivers/clk/imx/clk-imx6sl.c:156:6: warning: no previous prototype for ‘imx6sl_set_wait_clk’ [-Wmissing-prototypes]
Cc: Russell King <linux@armlinux.org.uk>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Ahmad Fatoum <a.fatoum@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
clkout1 and clkout2 allow to supply clocks from the SoC to the board,
which is used by some board designs to provide reference clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
clkout1 and clkout2 allow to supply clocks from the SoC to the board,
which is used by some board designs to provide reference clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PLL monitor is mentioned as a debug feature in the reference manual,
but there are some boards that use this clock output as a reference clock
for board level components. Add support for those clocks in the clock
driver, so this clock output can be used properly.
Note that the VIDEO1, GPU and VPU mux inputs are rotated compared to the
description in the reference manual. The order in this patch has been
empirically validated.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/imx/clk-imx31.c:54:28: warning: ‘uart_clks’ defined but not used [-Wunused-const-variable=]
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since 5d283b0838 ("clk: imx6: Fix procedure to switch the parent
of LDB_DI_CLK"), the clock driver warns if ldb_di\d_sel is changed
from reset value on system boot. This warning is printed even if
the bootloader (or a previous kernel that did kexec) followed the
correct procedure for glitch-free reparenting.
As such systems are doing everything correctly, a warning is too
harsh. Demote to a notice, so users are still alerted, but without
cluttering a loglevel=5 boot.
While at it, add the words "possible glitch" into the log message, to
make it more user-friendly.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A previous patch introduced a harmless randconfig warning:
WARNING: unmet direct dependencies detected for MXC_CLK_SCU
Depends on [n]: COMMON_CLK [=y] && ARCH_MXC [=n] && IMX_SCU [=y] && HAVE_ARM_SMCCC [=y]
Selected by [m]:
- CLK_IMX8QXP [=m] && COMMON_CLK [=y] && (ARCH_MXC [=n] && ARM64 [=y] || COMPILE_TEST [=y]) && IMX_SCU [=y] && HAVE_ARM_SMCCC [=y]
Since the symbol is now hidden and only selected by other symbols,
just remove the dependencies and require the other drivers to
get it right.
Fixes: 6247e31b75 ("clk: imx: scu: fix MXC_CLK_SCU module build break")
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201230155244.981757-1-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch corrects display clocks for i.MX8qxp DC0 subsystem by
calling imx_clk_scu2() to register them, instead of calling
imx_clk_scu(). The reason is that the clocks can source from
various parents. The clock source selection is controlled by
Distributed Slave System Controller(DSC). According to the DSC spec,
the below table describes the generic source selections for clocks
with the same type in various subsystems. And, the display controller
subsystem spec says the display clocks can source from PLL1, PLL2 or
bypass clock, thus we may specify the correct parents for imx_clk_scu2().
The bypass clock's parent is determined by the SCU firmware.
Currently, the parent is 'pixel_link_clk_in' from HW point of view.
To be more specific, the parent is dummy for i.MX8qxp DC0, while
HDMI TX PHY PLL for i.MX8qm DC0. In practice, the display clocks
source from the bypass clock only when driving i.MX8qm HDMI TX.
So, for the both display clocks, we simply specify 'dc0_bypass0_clk'
bypass clock as a valid parent.
-----------------------------------------
| src_sel[28:26] | |
-----------------------------------------
| 0x0 | xtal24M |
| 0x1 | PLL0 |
| 0x2 | PLL1 |
| 0x3 | PLL2 |
| 0x4 | bypass reference clock |
| 0x5 to 0x7 | reserved |
-----------------------------------------
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ability to get struct clk pointers from a struct clk_hw so that clk providers
can consume the clks they provide, if they need to do something like that. This
has been a long missing part of the clk provider API that will help us move
away from exposing a struct clk pointer in the struct clk_hw. Tracepoints are
added for the clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to help
developers understand the hardware enable state of clks in case firmware or
bootloader state is different than what is expected. Overall the core changes
are mostly improving the clk driver writing experience.
At the driver level, we have the usual collection of driver updates and new
drivers for new SoCs. This time around the Qualcomm folks introduced a good
handful of clk drivers for various parts of three or four SoCs. The SiFive
folks added a new clk driver for their FU740 SoCs, coming in second on the
diffstat and then Atmel AT91 and Amlogic SoCs had lots of work done after that
for various new features. One last thing to note in the driver area is that the
i.MX driver has gained a new binding to support SCU clks after being on the
list for many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and tweaks that
come from more testing and finding out that some configuration was wrong or
that a driver could support being built as a module.
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks
-----BEGIN PGP SIGNATURE-----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=Wt9O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework got some nice improvements this time around. We
gained the ability to get struct clk pointers from a struct clk_hw so
that clk providers can consume the clks they provide, if they need to
do something like that. This has been a long missing part of the clk
provider API that will help us move away from exposing a struct clk
pointer in the struct clk_hw. Tracepoints are added for the
clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to
help developers understand the hardware enable state of clks in case
firmware or bootloader state is different than what is expected.
Overall the core changes are mostly improving the clk driver writing
experience.
At the driver level, we have the usual collection of driver updates
and new drivers for new SoCs. This time around the Qualcomm folks
introduced a good handful of clk drivers for various parts of three or
four SoCs. The SiFive folks added a new clk driver for their FU740
SoCs, coming in second on the diffstat and then Atmel AT91 and Amlogic
SoCs had lots of work done after that for various new features. One
last thing to note in the driver area is that the i.MX driver has
gained a new binding to support SCU clks after being on the list for
many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and
tweaks that come from more testing and finding out that some
configuration was wrong or that a driver could support being built as
a module.
Summary:
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
dt-binding: clock: Document canaan,k210-clk bindings
dt-bindings: Add Canaan vendor prefix
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
clk: ingenic: Fix divider calculation with div tables
clk: sunxi-ng: Make sure divider tables have sentinel
clk: s2mps11: Fix a resource leak in error handling paths in the probe function
clk: mvebu: a3700: fix the XTAL MODE pin to MPP1_9
clk: si5351: Wait for bit clear after PLL reset
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
...
This issue can be reproduced by having a kernel config with
CONFIG_IMX_MBOX=m and CONFIG_MXC_CLK_SCU=m. It's caused by the Makefile
wanting to build clk-scu.o and clk-imx8qxp.o as different targets but
that doesn't work (e.g. MXC_CLK_SCU = y while CLK_IMX8QXP = n)
"obj-$(CONFIG_MXC_CLK_SCU) += clk-imx-scu.o clk-imx-lpcg-scu.o
clk-imx-scu-$(CONFIG_CLK_IMX8QXP) += clk-scu.o clk-imx8qxp.o"
Having MXC_CLK_SCU=y/m while CLK_IMX8QXP=n will cause a linker problem
like below:
LD [M] drivers/clk/imx/clk-imx-scu.o
arm-poky-linux-gnueabi-ld: no input files
Make MXC_CLK_SCU be un-selectable by users so it can only be selected by
the CLK_IMX8QXP option, ensuring the two symbols are built together.
Drop COMPILE_TEST too because this option isn't selectable anymore. We
can remove it from MXC_CLK_SCU because CLK_IMX8QXP selects MXC_CLK_SCU
which already has COMPILE_TEST.
Fixes: e0d0d4d86c ("clk: imx8qxp: Support building i.MX8QXP clock driver as module")
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20201130084624.21113-1-aisheng.dong@nxp.com
[sboyd@kernel.org: Rework commit text]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The device_is_bound() is invisible to drivers when built as modules.
It's also not aimed to be used by drivers according to Greg K.H.
Let's remove it from clk-scu driver and find another way to do proper
driver loading sequence.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Fixes: 77d8f3068c ("clk: imx: scu: add two cells binding support")
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the following sparse warning:
./clk-scu.c:23:20: warning: symbol 'pd_np' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mq.c:626:34: warning:
‘imx8mq_clk_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mp.c:751:34: warning:
‘imx8mp_clk_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mn.c:592:34: warning:
‘imx8mn_clk_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mm.c:641:34: warning:
‘imx8mm_clk_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch fixes below warning reported by coccicheck:
./clk-gate2.c:57:5-8: Unneeded variable: "ret". Return "0" on line 68
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
noc/axi/ahb are bus clk, not peripheral clk.
Since peripheral clk has a limitation that for peripheral clock slice,
IP clock slices must be stopped to change the clock source.
However if the bus clk is marked as critical clk peripheral, the
assigned clock parent operation will fail.
So we added CLK_SET_PARENT_GATE flag to avoid glitch.
And add imx8m_clk_hw_composite_bus_critical for bus critical clock usage
Fixes: 936c383673 ("clk: imx: fix composite peripheral flags")
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1604229834-25594-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Protect against enabling/disabling the gate while we're
checking if it is enabled.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On some i.MX8 platforms, there are HW gates that share the same bit.
So in order to make this clock type more usable, use a mask to specify
how many bits belong to those HW gates.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Seems the logic here was wrong all along. For example, if
the cgr_val is 2 (0b10), the clk_gate2_reg_is_enabled would
report the clock as disabled. So check against cgr_val instead.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move all the register writing to the newly added clk_gate2_do_shared_clks
and call that everywhere need needed. Cleans up the code a little bit.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This was a hack which would allow multiple HW gates to be controlled
by a single bit. The only user of this is the imx_dev_clk_hw_gate_shared
which is not used anywhere as of now. Basically, complicates the logic
of the driver for no reason.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After commit e0d0d4d86c ("clk: imx8qxp: Support building i.MX8QXP clock
driver as module"), clk-scu.c and clk-imx8qxp.c are complied in one module,
thus there can be only one module_init() in those two files.
Commit 77d8f3068c ("clk: imx: scu: add two cells binding support")
introduced another module_init() in clk_scu.c which caused the errors
below.
To fix the issue, we can remove the unnecessary builtin_platform_driver
from clk_scu.c and directly register the driver in imx_clk_scu_init().
CC [M] drivers/clk/imx/clk-scu.o
In file included from ../include/linux/of_device.h:6,
from ../include/linux/of_platform.h:12,
from ../drivers/clk/imx/clk-scu.c:11:
../drivers/clk/imx/clk-scu.c: In function ‘imx_clk_scu_init’:
../drivers/clk/imx/clk-scu.c:176:35: error: ‘imx_clk_scu_driver’ undeclared (first use in this function); did you mean ‘imx_clk_scu_init’?
176 | return platform_driver_register(&imx_clk_scu_driver);
| ^~~~~~~~~~~~~~~~~~
../include/linux/platform_device.h:218:29: note: in definition of macro ‘platform_driver_register’
218 | __platform_driver_register(drv, THIS_MODULE)
| ^~~
../drivers/clk/imx/clk-scu.c:176:35: note: each undeclared identifier is reported only once for each function it appears in
176 | return platform_driver_register(&imx_clk_scu_driver);
| ^~~~~~~~~~~~~~~~~~
../include/linux/platform_device.h:218:29: note: in definition of macro ‘platform_driver_register’
218 | __platform_driver_register(drv, THIS_MODULE)
| ^~~
../drivers/clk/imx/clk-scu.c:177:1: error: control reaches end of non-void function [-Werror=return-type]
177 | }
| ^
At top level:
../drivers/clk/imx/clk-scu.c:470:31: warning: ‘imx_clk_scu_driver’ defined but not used [-Wunused-variable]
470 | static struct platform_driver imx_clk_scu_driver = {
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 77d8f3068c ("clk: imx: scu: add two cells binding support")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pointer np is being initialized with a value that is never read
and it is being updated with a value later on. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A semicolon is not needed after a switch statement.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LPCG clock state may be lost when it's power domain is completely
off during system suspend/resume and we need save and restore the
state properly.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Used to support runtime pm.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
One LPCG controller supports up to 8 clock outputs while each of them
is fixed to 4 bits. It supports only gating function with fixed bits.
So we can use the clk-indices to fetch the corresponding clock idx from
device tree. With this way, we can write a generic LPCG clock drivers.
This patch add that support to parse clocks from device tree.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Clock state will be lost when its power domain is completely off
during system suspend/resume. So we save and restore the state
accordingly in suspend/resume callback.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bypass cpu power domains which are owned by ATF.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch implements the new two cells binding for SCU clocks.
The usage is as follows:
clocks = <&uart0_clk IMX_SC_R_UART_0 IMX_SC_PM_CLK_PER>
Due to each SCU clock is associated with a power domain, without power
on the domain, the SCU clock can't work. So we create platform devices
for each domain clock respectively and manually attach the required domain
before register the clock devices, then we can register clocks in the
clock platform driver accordingly.
Note because we do not have power domain info in device tree and the SCU
resource ID is the same for power domain and clock, so we use resource ID
to find power domains.
Later, we will also use this clock platform driver to support suspend/resume
and runtime pm.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
According to the latest RM (see Table 5-1. Clock Root Table),
both usdhc root clocks have the parent order as follows:
000 - 25M_REF_CLK
001 - SYSTEM_PLL1_DIV2
010 - SYSTEM_PLL1_CLK
011 - SYSTEM_PLL2_DIV2
100 - SYSTEM_PLL3_CLK
101 - SYSTEM_PLL1_DIV3
110 - AUDIO_PLL2_CLK
111 - SYSTEM_PLL1_DIV8
So the audio_pll2_out and sys3_pll_out have to be swapped.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Cosmin Stefan Stoica <cosmin.stoica@nxp.com>
Link: https://lore.kernel.org/r/1602753944-30757-1-git-send-email-abel.vesa@nxp.com
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As i.MX21 support has been removed, get rid of its clock driver too.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx35_clocks_init() has been used to register clocks on i.MX35
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx35_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx31_clocks_init() has been used to register clocks on i.MX31
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx31_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx27_clocks_init() has been used to register clocks on i.MX27
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx27_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A few words were misspelled in this comment.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix and add missing kerneldoc to fix compile warnings like:
drivers/clk/imx/clk-pfd.c:27: warning: Function parameter or member 'hw' not described in 'clk_pfd'
drivers/clk/imx/clk-pllv3.c:53: warning: Function parameter or member 'ref_clock' not described in 'clk_pllv3'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to RM, Page 574, Chapter 5.2.6.4.3 Peripheral clock slice,
"IP clock slices must be stopped to change the clock source.".
So we must have CLK_SET_PARENT_GATE flag to avoid glitch.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to RM, for peripheral clock slice,
"IP clock slices must be stopped to change the clock source.".
So we must have CLK_SET_PARENT_GATE flag to avoid glitch.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The root clock slice at offset 0xbf80 should be memrepair
clock, so correct it. And this clock should be always on
to make sure the memory repair function can works well.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The root clock slice at 0xbf00 is media_ldb clock,
not csi_phy2_ref, so correct it.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the clock for CRC block allowing it to be enabled by consumers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is better to explicitly include the required header file rather
then get it through some recursive include.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change configuration to "tristate", add module author, description and
license to support building i.MX8QXP clock drivers as module.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change configuration to "tristate", add module author, description
and license to support building i.MX8M SoCs clock driver as module.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add CONFIG_CLK_xxx for i.MX ARMv7 platforms, and use it as build option
instead of CONFIG_SOC_xxx, the CONFIG_CLK_xxx will be selected by default
according to CONFIG_SOC_xxx.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are more and more requirements of building SoC specific drivers
as modules, add support for building i.MX common clock driver as module
to meet the requirement.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use readl_relaxed() instead of __raw_readl(), and use BIT(x)
instead of (1 << X) to fix below build warning reported by kernel
test robot:
drivers/clk/imx/clk-imx6sl.c:149:49: warning: Shifting signed 32-bit
value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
while (!(__raw_readl(anatop_base + PLL_ARM) & BM_PLL_ARM_LOCK))
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
* clk-fallthru:
clk: davinci: Use fallthrough pseudo-keyword
clk: imx: Use fallthrough pseudo-keyword
* clk-ingenic:
clk: X1000: Add support for calculat REFCLK of USB PHY.
clk: JZ4780: Reformat the code to align it.
clk: JZ4780: Add functions for enable and disable USB PHY.
clk: Ingenic: Add RTC related clocks for Ingenic SoCs.
dt-bindings: clock: Add tabs to align code.
dt-bindings: clock: Add RTC related clocks for Ingenic SoCs.
* clk-tegra:
clk: tegra: pll: Improve PLLM enable-state detection
* clk-sirf:
clk: clk-atlas6: fix return value check in atlas6_clk_init()
* clk-qoriq:
clk: qoriq: add LS1021A core pll mux options
Add mu root clk for mu mailbox usage.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the bus clk use imx8m_clk_hw_composite_bus, then
we could avoid possible issue when setting mux of the clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Introduce imx8m_clk_hw_composite_bus api for bus clk root slice usage.
Because the mux switch sequence issue, we could not reuse Peripheral
Clock Slice code, need use composite specific mux operation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CORE/BUS root slice has following design, simplied graph:
The difference is core not have pre_div block.
A composite core/bus clk has 8 inputs for mux to select, saying clk[0-7].
It support target(smart) interface and normal interface. Target interface
is exported for programmer easy to configure ccm root. Normal interface
is also exported, but we not use it in our driver, because it will
introduce more complexity compared with target interface.
The normal interface simplified as below:
SEL_A GA
+--+ +-+
| +->+ +------+
CLK[0-7]--->+ | +-+ |
| | | +----v---+ +----+
| +--+ |pre_diva+----> | +---------+
| +--------+ |mux +--+post_div |
| +--+ |pre_divb+--->+ | +---------+
| | | +----^---+ +----+
+--->+ | +-+ |
| +->+ +------+
+--+ +-+
SEL_B GB
The mux in the upper pic is not the target interface MUX, target
interface MUX is hiding SEL_A and SEL_B. When you choose clk[0-7],
you are actually writing SEL_A or SEL_B depends on the internal
counter which will also control the internal "mux".
The target interface simplified as below which is used by Linux Kernel:
CLK[0-7]--->MUX-->Gate-->pre_div-->post_div
A requirement of the Target Interface's software is that the
target clock source is active, it means when setting SEL_A, the
current input clk to SEL_A must be active, same to SEL_B.
We touch target interface, but hardware logic actually also need
configure normal interface.
There will be system hang, when doing the following steps:
The initial state:
SEL_A/SEL_B are both sourcing from clk0, the internal counter
choose SEL_A.
1. switch mux from clk0 to clk1
The hardware logic will choose SEL_B and configure SEL_B to clk1.
SEL_A no changed.
2. gate off clk0
Disable clk0, then the input to SEL_A is off.
3. swtich from clk1 to clk2
The hardware logic will choose SEL_A and configure SEL_A to clk2,
however the current SEL_A input clk0 is off, the system hang.
The solution to fix the issue is in step 1, write twice to
target interface MUX, it will make SEL_A/SEL_B both sources
from clk1, then no need to care about the state of clk0. And
finally system performs well.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Migrate A53 clk root to use composite core clk type. It
will simplify code and make it easy to use composite
specific mux operation.
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx8m_clk_hw_composite_core to simpliy clks that belong to
core clk slice.
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Inspried from
commit e8688fe8df ("clk: imx8mn: Define gates for pll1/2 fixed dividers")
On imx8mp there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate. Only one of these gates (the one "dividing" by
one) is currently defined and it's incorrectly set as the parent of all
the fixed-factor dividers.
Add the other 8 gates to the clock tree between sys_pll1/2_bypass and
the fixed dividers.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Same to i.MX8MN/i.MX8MM, pll BYPASS bit should be kept inside pll
driver for glitchless freq setting following spec. If exposing the
bit, that means pll driver and clk driver has two paths to touch
this bit, which is wrong.
So use EXT_BYPASS bit here.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The parent settings have been moved to dtsi, we no need to
set parent here. And clk_hw_set_parent will trigger lockdep warning,
because this api not have prepare_lock.
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All the imx clocks that need to be registered by the audiomix need to
pass on the device so that the runtime PM support could work properly.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to allow runtime PM, the device needs to be passed on
to the register function. Audiomix clock controller, used on
i.MX8MP and future platforms, registers a pll14xx and has runtime
PM support.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Audiomix on i.MX8MP registers two gates that share the same enable count
but use the same bit to control the gate instead of two bits. By adding
the flag IMX_CLK_GATE2_SINGLE_BIT we allow the gate2 to use the generic
gate ops for enable, disable and is_enabled.
For the disable_unused, nothing happens if this flag is specified.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use readl_relaxed_poll_timeout() for PLL lock wait which can simplify the
code a lot.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove many unnecessary blank lines for cleanup.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Moving to support aarch32 mode on aarch64 hardware, need to drop
the dependency on ARM64 to make the driver could be selected for
ARM32.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ARM clk could only source from divcore or hsrun_divcore.
Follow what we already used on i.MX7D and i.MX8M SoCs, use
imx_clk_hw_cpu API. When ARM core is running normaly,
whether divcore or hwrun_divcore will finally source
from SPLL_PFD0. However SPLL_PFD0 is marked with CLK_SET_GATE,
so we need to disable SPLL_PFD0, when configure the rate.
So add CORE and HSRUN_CORE virtual clk to make it easy to
configure the clk using imx_clk_hw_cpu API.
Since CORE and HSRUN_CORE already marked with CLK_IS_CRITICAL, no
need to set ARM as CLK_IS_CRITICAL. And when set the rate of ARM clk,
prograting it the parent with CLK_SET_RATE_PARENT will finally set
the SPLL_PFD0 clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Setting a CAN bitrate of 800kbit/s fails with a bitrate error of 1.3% if the
flexcan module is clocked at 30MHz (CAN_CLK_ROOT). This patch changes the clock
frequency from 30MHz to 40MHz which allows to support all bitrates recommended
by CiA.
The patch sets CAN_CLK_SEL to 80MHz by changing its clock parent from
CLK_PLL3_60M to CLK_PLL3_80M. The post-divider CAN_CLK_PODF is set to /2 by
default which makes 40MHz CAN_CLK_ROOT from its parent CAN_CLK_SEL.
Background:
CAN in Automation document 102 (CiA102) recommends the CAN bitrates 10, 20, 50,
125, 250, 500, 800 and 1000kbit/s.
With the flexcan serial clock at 30MHz (original value) setting some common
bitrates ("ip link set canX type can bitrate <bitrate>") gives the following
results:
requested value / actually set value
5000: bitrate 5000 sample-point 0.708
10000: bitrate 10000 sample-point 0.866
20000: bitrate 20000 sample-point 0.866
40000: bitrate 40000 sample-point 0.866
50000: bitrate 50000 sample-point 0.866
80000: bitrate 80000 sample-point 0.866
100000: bitrate 100000 sample-point 0.866
125000: bitrate 125000 sample-point 0.875
250000: bitrate 250000 sample-point 0.866
400000: bitrate 400000 sample-point 0.866
500000: bitrate 500000 sample-point 0.866
666666: bitrate 666666 sample-point 0.800
800000: bitrate 789473 sample-point 0.789 !!!bitrate error 1.3%
1000000: bitrate 1000000 sample-point 0.733
With the flexcan serial clock at 40MHz (new value) we get this:
5000: no more possible
10000: bitrate 10000 sample-point 0.875
20000: bitrate 20000 sample-point 0.875
40000: bitrate 40000 sample-point 0.850
50000: bitrate 50000 sample-point 0.875
80000: bitrate 80000 sample-point 0.850
100000: bitrate 100000 sample-point 0.875
125000: bitrate 125000 sample-point 0.875
250000: bitrate 250000 sample-point 0.875
400000: bitrate 400000 sample-point 0.850
500000: bitrate 500000 sample-point 0.875
666666: bitrate 666666 sample-point 0.800
800000: bitrate 800000 sample-point 0.800
1000000: bitrate 1000000 sample-point 0.750
A drawback of the modification is that 5kbit/s is no more supported.
Setting the flexcan serial clock to 60MHz or 80MHz would produce similar
results but with losing even more bitrates at the lower end.
Changing the flexcan serial clock to 40MHz might apply for other SoCs
using the flaxcan module as well (e.g. imx6q/d/s..). But since I don't
have such hardware to test I did not add this to the patch.
Signed-off-by: Georg Waibel <georg.waibel@wiedemann-group.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
majority of the diff is the normal collection of driver additions for new SoCs
and non-critical clk data fixes and updates. The framework must be middle aged.
The two biggest directories in the diffstat show that the Qualcomm and Unisoc
support added a handful of big drivers for new SoCs but that's not really the
whole story because those new drivers tend to add large numbers of lines of clk
data. There's a handful of AT91 clk drivers added this time around too and a
bunch of improvements to drivers like the i.MX driver. All around lots of
updates and fixes in various clk drivers which is good to see.
The core framework has only one real major change which has been baking in next
for the past couple months. It fixes the framework so that it stops caching a
clk's phase when the phase clk_op returns an error. Before this change we would
consider some negative errno as a phase and that just doesn't make sense.
Core:
- Don't show clk phase when it is invalid
New Drivers:
- Add support for Unisoc SC9863A clks
- Qualcomm SM8250 RPMh and MSM8976 RPM clks
- Qualcomm SM8250 Global Clock Controller (GCC) support
- Qualcomm SC7180 Modem Clock Controller (MSS CC) support
- EHRPWM's TimeBase clock(TBCLK) for TI AM654 SoCs
- Support PMC clks on at91sam9n12, at91rm9200, sama5d3, and at91sam9g45 SoCs
Updates:
- GPU GX GDSC support on Qualcomm sc7180
- Fixes and improvements for the Marvell MMP2/MMP3 SoC clk drivers
- A series from Anson to convert i.MX8 clock bindings to json-schema
- Update i.MX pll14xx driver to include new frequency entries for pll1443x table,
and return error for invalid PLL type
- Add missing of_node_put() call for a number of i.MX clock drivers
- Drop flag CLK_IS_CRITICAL from 'A53_CORE' mux clock, as we already
have the flag on its child cpu clock
- Fix a53 cpu clock for i.MX8 drivers to get it source from ARM PLL
via CORE_SEL slice, and source from A53 CCM clk root when we need to
change ARM PLL frequency. Thus, we can support core running above
1GHz safely
- Update i.MX pfdv2 driver to check zero rate and use determine_rate for
getting the best rate
- Add CLKO2 for imx8mm, SNVS clock for imx8mn, and PXP clock for imx7d
- Remove PMC clks from Tegra clk driver
- Improved clock/reset handling for the Renesas R-Car USB2 Clock Selector
- Conversion to json-schema of the Renesas CPG/MSSR DT bindings
- Add Crypto clocks on Renesas R-Car M3-W/W+, M3-N, E3, and D3
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Update Amlogic audio clock gate hierarchy for meson8 and gxbb
- Update Amlogic g12a spicc clock sources
- Support for Ingenic X1000 TCU clks
-----BEGIN PGP SIGNATURE-----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=ZoI6
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There's not much to see in the core framework this time around.
Instead the majority of the diff is the normal collection of driver
additions for new SoCs and non-critical clk data fixes and updates.
The framework must be middle aged.
The two biggest directories in the diffstat show that the Qualcomm and
Unisoc support added a handful of big drivers for new SoCs but that's
not really the whole story because those new drivers tend to add large
numbers of lines of clk data. There's a handful of AT91 clk drivers
added this time around too and a bunch of improvements to drivers like
the i.MX driver. All around lots of updates and fixes in various clk
drivers which is good to see.
The core framework has only one real major change which has been
baking in next for the past couple months. It fixes the framework so
that it stops caching a clk's phase when the phase clk_op returns an
error. Before this change we would consider some negative errno as a
phase and that just doesn't make sense.
Core:
- Don't show clk phase when it is invalid
New Drivers:
- Add support for Unisoc SC9863A clks
- Qualcomm SM8250 RPMh and MSM8976 RPM clks
- Qualcomm SM8250 Global Clock Controller (GCC) support
- Qualcomm SC7180 Modem Clock Controller (MSS CC) support
- EHRPWM's TimeBase clock(TBCLK) for TI AM654 SoCs
- Support PMC clks on at91sam9n12, at91rm9200, sama5d3, and
at91sam9g45 SoCs
Updates:
- GPU GX GDSC support on Qualcomm sc7180
- Fixes and improvements for the Marvell MMP2/MMP3 SoC clk drivers
- A series from Anson to convert i.MX8 clock bindings to json-schema
- Update i.MX pll14xx driver to include new frequency entries for
pll1443x table, and return error for invalid PLL type
- Add missing of_node_put() call for a number of i.MX clock drivers
- Drop flag CLK_IS_CRITICAL from 'A53_CORE' mux clock, as we already
have the flag on its child cpu clock
- Fix a53 cpu clock for i.MX8 drivers to get it source from ARM PLL
via CORE_SEL slice, and source from A53 CCM clk root when we need
to change ARM PLL frequency. Thus, we can support core running
above 1GHz safely
- Update i.MX pfdv2 driver to check zero rate and use determine_rate
for getting the best rate
- Add CLKO2 for imx8mm, SNVS clock for imx8mn, and PXP clock for
imx7d
- Remove PMC clks from Tegra clk driver
- Improved clock/reset handling for the Renesas R-Car USB2 Clock
Selector
- Conversion to json-schema of the Renesas CPG/MSSR DT bindings
- Add Crypto clocks on Renesas R-Car M3-W/W+, M3-N, E3, and D3
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car H3, M3-W/W+, and
M3-N
- Update Amlogic audio clock gate hierarchy for meson8 and gxbb
- Update Amlogic g12a spicc clock sources
- Support for Ingenic X1000 TCU clks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (146 commits)
clk: sprd: fix to get a correct ibias of pll
dt-bindings: imx8mm-clock: Fix the file path
dt-bindings: imx8mq-clock: Fix the file path
clk: qcom: rpmh: Drop unnecessary semicolons
clk: qcom: rpmh: Simplify clk_rpmh_bcm_send_cmd()
clk: tegra: Use NULL for pointer initialization
clk: sprd: add clocks support for SC9863A
clk: sprd: support to get regmap from parent node
clk: sprd: Add macros for referencing parents without strings
clk: sprd: Add dt-bindings include file for SC9863A
dt-bindings: clk: sprd: add bindings for sc9863a clock controller
dt-bindings: clk: sprd: rename the common file name sprd.txt to SoC specific
clk: sprd: add gate for pll clocks
MAINTAINERS: dt: update reference for arm-integrator.txt
clk: mmp2: Fix bit masks for LCDC I/O and pixel clocks
clk: mmp2: Add clock for fifth SD HCI on MMP3
dt-bindings: marvell,mmp2: Add clock id for the fifth SD HCI on MMP3
clk: mmp2: Add clocks for the thermal sensors
dt-bindings: marvell,mmp2: Add clock ids for the thermal sensors
clk: mmp2: add the GPU clocks
...
Most of the commits are for additional hardware support and minor fixes
for existing machines for all the usual platforms: qcom, amlogic, at91,
gemini, mediatek, ti, socfpga, i.mx, layerscape, uniphier, rockchip,
exynos, ux500, mvebu, tegra, stm32, renesas, sunxi, broadcom, omap,
and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation.
Andre Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into
dts files, for many devices that relied on a mix of auxiliary data
in addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants, along
with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based on
the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=ye2F
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: 666aed2d13 ("clk: imx: scu: add set parent support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/aad021e432b3062c142973d09b766656eec18fde.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: fe37b48204 ("clk: imx: add scu clock common part")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/10e97a04980d933b2cfecb6b124bf9046b6e4f16.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The device needs to be passed on to the clk_hw_register.
Fixes: 1f9aec9662 ("clk: imx: clk-gate2: Switch to clk_hw based API")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PXP has a single CCGR clock gate, gating both the IPG_CLK_ROOT and
the MAIN_AXI_CLK_ROOT. Add a single clock to cover both.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
enet_qos is for eqos tsn AXI bus clock whose clock source is from
ccm_enet_axi_clk_root, and controlled by CCM_CCGR59(offset 0x43b0)
and CCM_CCGR64(offset 0x4400), so correct enet_qos root clock's
parent clock to sim_enet.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IMX8MP_CLK_HDMI_AXI should be from imx8mp_media_axi_sels instead
of imx8mp_media_apb_sels, fix it.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not good to use enable/disable for PLLv4 which needs time to
lock, because enable/disable is expected to be able run in
interrupt context. So use prepare/unprepare.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pfdv2 is only used in i.MX7ULP. To get best pfd output, the i.MX7ULP
Datasheet defines two best PLL rate and pfd frac.
Per Datasheel
All PLLs on i.MX 7ULP either have VCO base frequency of
480 MHz or 528 MHz. So when determine best rate, we also
determine best parent rate which could match the requirement.
For some reason the current parent might not be 480MHz or 528MHz,
so we still take current parent rate as a choice.
And we also enable flag CLK_SET_RATE_PARENT to let parent rate
to be configured.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per clk_ops, compared with round_rate, determine_rate could optionally
support the parent clock that should be used to provide the clock rate.
In this patch, the parent clock is just parent->rate as round_rate.
The following patch will calculate the best parent clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
No need to initialize 'ret' in many functions, as it will get
the return value from function call, so remove the initializtion
of 'ret'.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When pll type is invalid, ONLY output error message is NOT enough,
should return error immediately.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A53 CCM clk root only accepts input up to 1GHz, CCM A53 root
signoff timing is 1Ghz, however the A53 core which sources from CCM
root could run above 1GHz which voilates the CCM.
There is a CORE_SEL slice before A53 core, we need configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Mark arm_a53_core as critical clk
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A53 CCM clk root only accepts input up to 1GHz, CCM A53 root
signoff timing is 1Ghz, however the A53 core which sources from CCM
root could run above 1GHz which voilates the CCM.
There is a CORE_SEL slice before A53 core, we need configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Mark arm_a53_core as critical clk.
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
