Unfortunatey there appear to quite a few HSW/BDW machines (eg.
NUCs, Brix Pro) in the wild with LPT/WPT-H that have no physical
CRT connector and non-working FDI. FDI training fails every
single time on these machines. Dunno, maybe they just didn't
bother wiring it up or something?
Unfortunately all the fuse bits and whatnot are telling us that
the CRT connector is present. And so what we get from this is tons
of false positives from the CI systems due to VGA connector forcing.
I've not found any way to detect this purely from hardware, so we
have to resort to looking at the VBT int_crt_support bit. We used
to check this bit on all platforms, but that broke all the old
machines, so the check was then restricted to VLV only in
commit 84b4e042c4 ("drm/i915: only apply crt_present check on VLV")
Considering HSW and VLV VBT probably got defined around the same time,
it should be reasonably safe to assume that the bits is sane for
HSW/BDW as well. At least I have one copy of some VBT spec here that
says it's meant for both VLV and HSW, and it knows about the bit
(lists it being valid from version 155 onwards). Also I have two
desktop machines with actual CRT ports and both have
int_crt_support==1 in their VBTs.
Also we already trust VBT >= 155 to tell us various details about
the DDI ports, so trusting it a bit more seems reasonable.
As far as VLV goes, the added VBT version check should be fine. Even
if someone has some weird VLV machine with a very old VBT version,
it just means they'll end up with a shadow CRT connector. IIRC the
reason for eliminating the shadow CRT connector on VLV was to speed
up display probing rather than fixing something more serious.
v2: Move the platform checks into the VBT parsing code
Also check that the VBT version is at least 155
v3: Improve commit message (Paulo)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449005493-15487-1-git-send-email-ville.syrjala@linux.intel.com
On HSW/BDW DDI A and E share 2 lanes, so when DDI A requires the
shared lanes DDI E can't be used. The lanes are not supposed to
be dynamically switched between the two uses, so there's no point
in registering the CRT connector when DDI E has no lanes.
v2: Fix typos in the commit message (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449005396-15319-1-git-send-email-ville.syrjala@linux.intel.com
LPT-H has a strap bit for fused off CRT block. Check it to see if
we should register the CRT connector or not. Supposedly this also
forces the ADAP enable bit to 0, so the detection we added in
commit 6c03a6bd0d ("drm/i915: Don't register CRT connector when it's fused off")
should already catch it, but checking the fuse bit should at least
do no harm.
v2: Use HAS_PCH_LPT_H() (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449005335-15192-1-git-send-email-ville.syrjala@linux.intel.com
Currently we round the AUX clock divider down on g4x, to closest
on HSW/BDW port A, and up everywhere else. We are supposed to get
as close to 2MHz as we can, so round to closest seems like the
best option.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448893432-6978-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Somehow we accumulated a duplicated .get_display_clock_speed()
assignment for PNV in
commit 34edce2fea ("drm/i915: Add cdclk extraction for g33, g965gm and g4x")
No real harm on having two, we just never reach the second one, so
simply kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448893432-6978-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Per bspec, "Backlight PWM may stop in the asserted state, causing
backlight to stay fully on. WA: Before disabling PWM, set CLKGATE_DIS_0
0x46530 bit 13 PWM1 Gating Dis (for PWM1) or bit 14 PWM2 Gating Dis (for
PWM2). The bits can remain set without harm." (There's no workaround
name for this.)
This fixes some Broxton backlight issues.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: cleanup & commit message]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448958232-26520-3-git-send-email-jani.nikula@intel.com
If the backlight modulation frequency can't be extracted from the
registers or from VBT, use 200 Hz as the default. This may enable
backlight on some machines that previously failed.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448958232-26520-2-git-send-email-jani.nikula@intel.com
The only missing piece is the function to convert frequency to PWM
register value. The PWM is based on 19.2 MHz clock, except for BXT A
step, which is based on CDCLK, and which we ignore.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448958232-26520-1-git-send-email-jani.nikula@intel.com
BXT power well support is not yet stable. Starting with patch
commit 9f836f9016
Author: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Date: Mon Nov 16 16:20:01 2015 +0100
drm/i915/gen9: Turn DC handling into a power well
DPMS off operations may actually cause the entire system to powerdown or
reboot. Disable power well support for now until Broxton gets fixes
similar to what we have for SKL.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
References: http://lists.freedesktop.org/archives/intel-gfx/2015-November/081037.html
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448990818-11005-1-git-send-email-matthew.d.roper@intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The .get_config() hooks should not reference anything in crtc->config,
everything should be based on the passed in pipe_config instead. So
don't dig out the cpu_transcoder from crtc->config on ddi platfforms,
and also avoid using the encoder->crtc link and instead look up the
pipe via pipe_config->base.crtc.
I don't think this will actually fix anything since during the initial
state readout we set up the encoder->crtc link prior to calling
.get_config(), and during the modeset state check the encoder->crtc
ought to be correct anyway since it's that state we just programmed.
But this seems the right thing to do anyway.
While at it, do some house cleaning on the local variables in the
.infoframe_enabled() hooks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448555227-31403-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to
commit 37ca8d4ccd
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Oct 30 19:20:27 2015 +0200
drm/i915: Enable PCH FIFO underruns later on ILK/SNB/IVB
we can only enable fifo underrun reporting when using the fdi/lpt
after everything is set up and after a bit of waiting. The waiting
is required, enabling it right after enabling encoders will first trigger
an underrun on the pch and then, 1 frame later, an underrun on the
cpu. Two vblank waits after encoder enabling seems enough to curb it.
And similar to
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Nov 20 22:09:18 2015 +0200
drm/i915: Suppress spurious CPU FIFO underruns on ILK-IVB
we also need to make sure cpu fifo underrun reporting is disabled when
enabling the fdi rx/tx and pch transcoder&port. But somehow this is
only needed when enabling, not also when disabling.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448705139-12534-1-git-send-email-daniel.vetter@ffwll.ch
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91578
Tested-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DSI has quite a few special cases, like DP, so add it to crtc
state. This way we can get rid of a number of intel_pipe_has_type()
checks for DSI. This isn't necessarily the prettiest way, but it's a
step towards being aligned with what's being done with other encoders.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448619706-21293-3-git-send-email-jani.nikula@intel.com
The hook was added to cater for DSI, but with the hooks rearranged on
the DSI encoder side, this is no longer needed. It was a bit silly
anyway to have two hooks called back-to-back.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448619706-21293-2-git-send-email-jani.nikula@intel.com
For DSI, the pre_pll_enable and the pre_enable hooks are called
back-to-back on all platforms that support DSI. The distinction is
artificial for DSI, for which we enable the DSI PLL in the encoder
hooks. Do everything in pre_enable, and remove DSI pre_pll_enable hook.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448619706-21293-1-git-send-email-jani.nikula@intel.com
Found by static code analysis tool.
v2: Inserted block instead of goto & renamed variables (Chris)
v3: Aligned code as per the opening brace (Chris)
Rebased on top of nightly (Daniel)
Signed-off-by: Namrta Salonie <namrta.salonie@intel.com>
Signed-off-by: Deepak S <deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ironlake_{enable,disable}_display_irq() each just call
ilk_update_display_irq() so let's make them static inlines.
While at it s/ironlake/ilk/ to make things shorter, and a bit more
consistent with the ibx functions.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448294777-13722-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts
commit 97e5ed1111
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Oct 23 10:56:12 2015 +0200
drm/i915: shut up gen8+ SDE irq dmesg noise
With the proper fix ("drm/i915: fix the SDE irq dmesg warnings
properly") reliably in place, bring back the error message.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448462843-32739-2-git-send-email-jani.nikula@intel.com
We had the "The master control interrupt lied (SDE)!" check and error
message in place for a long time without any problems, until
commit aaf5ec2e51
Author: Sonika Jindal <sonika.jindal@intel.com>
Date: Wed Jul 8 17:07:47 2015 +0530
drm/i915: Handle HPD when it has actually occurred
caused the errors to start happening. This was bisected and reported,
but the error message was silenced in
commit 97e5ed1111
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Oct 23 10:56:12 2015 +0200
drm/i915: shut up gen8+ SDE irq dmesg noise
shooting the messenger while the debugging for why Sonika's commit
triggered the errors was still in progress.
It looks like we need to read and acknowledge the PCH_PORT_HOTPLUG
register even though the hotplug trigger indicates there isn't a hotplug
irq to handle. The PCH doesn't seem to really ack the the interrupt to
the CPU unless we touch the hotplug register.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92084
Fixes: aaf5ec2e51 ("drm/i915: Handle HPD when it has actually occurred")
[Jani: added a comment and amended the commit message while applying]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448462843-32739-1-git-send-email-jani.nikula@intel.com
Commit "30c964a drm/i915: Detect virtual south bridge" detects and
handles the southbridge emulated by vmware esx. Add the ich9 south
bridge emulated by 'qemu -M q35'.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit b04c5bd6fd
Author: Borun Fu <borun.fu@intel.com>
Date: Sat Jul 12 10:02:27 2014 +0530
drm/i915: Power gating display wells during i915_pm_suspend
moved for_each_power_domain from intel_display.c to i915_drv.h but we
still have the definition around in intel_display.c, due to a merge
conflict resolution gone wrong in
commit 4dac3edfe6
Merge: 487777673ee05444be70
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 29 20:49:36 2014 +0200
Merge remote-tracking branch 'airlied/drm-next' into drm-intel-next
Just remove the extra definition left behind.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448383645-7615-1-git-send-email-jani.nikula@intel.com
On some machines the CRT connector may be fused off. The weird thing
about this setup is that the ADPA register works otherwise normally,
except the enable bit is hardwired to 0. No one knows of any fuse
register that would tell us if this is the case, so the only thing we
can do (apart from a blacklist) is to try and set the enable bit and see
if it sticks. If not, we don't register the connector at all. Obviously
if the bit is already set when loading the driver we can just assume it
works.
I've smoke tested this approach on several machines (GMCH and PCH),
some with actual CRT connectors, some with shadow connectors, and
obviously the machine (IVB) with the fused off connector. So far
I've not seen any ill effects from this probe.
The main benefit is that we can actually run igt on machines with
fused off connectors, without totally upsetting the state checker.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448051741-22771-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
To get a better idea if underruns occurred during crtc disabling,
let's check for them explicitly. This helps in cases where the
error interrupt isn't active, or there is no underrun interrupt
support at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448050160-14124-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We sometimes get a spurious CPU pipe underrun somewhere between
enabling port A and enabling vdd for the panel. Observed on both
ILK and IVB with port A eDP. Suppress FIFO underrun reporting
around the port and vdd enable to avoid the dmesg errors.
Not sure if port D eDP would suffer from the same issue, but assume
that it doesn't until proven differently.
Testcase: igt/kms_setmode
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448050160-14124-2-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
We still get spurious pipe underruns on ILK/SNB/IVB under two
circumstances when dealing with PCH ports:
* When the pipe has been disabled, but FDI RX/TX is still enabled
* During FDI link training
Both cases seem to happen at least when we do VGA+HDMI cloning
from the same pipe. I don't think I've seen them when not cloning,
but can't be 100% sure.
Disable underrun reporting around those places to eliminate the
dmesg errors.
Testcase: igt/kms_setmode/basic-clone-single-crtc
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448050160-14124-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
It is not a bad idea to disable the PSR feature on Sink
when we are disabling on the Source.
v2: Move dpcd write inside mutex protected area as suggested by Sonika.
Cc: Sonika Jindal <sonika.jindal@intel.com>
Suggested-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whenever DMC firmware put the HW into DC State a bunch
of registers including this perf counter is reset to 0.
Even with PSR active and working we could still read
"Performance_Counter: 0" what will misslead people to believe
PSR is broken. For instance on SKL we can only see PC10
residency with screen on if PSR is working properly.
However Performance_Counter was showing 0.
Even if it restored properly on DC6 exit we don't want to
give users the wrong impression that PSR is not working
while we know for sure it is.
So, it is better to remove this counter information while
we don't have a better way to track PSR residency.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we introduced PSR we let LPSP masked allowing us to get PSR
independently from the audio runtime PM. However in one of the
attempts to get PSR enabled by default one user reported one specific
case where he would miss screen updates if scrolling the firefox in a
Gnome environment when i915 runtime pm was enabled. So for
this specific case that (I could never create an i-g-t test case)
we decided to remove the LPSP mask and let HW tracking taking care of
this case. The mask got removed later by my
commit 09108b90f0 ("drm/i915: PSR: Remove Low Power HW tracking mask.")
So we started depending on audio driver again, what is bad.
With previous commit
"drm/i915: PSR: Let's rely more on frontbuffer tracking."
we transfered the PSR exit responsability totally to SW frontbuffer
tracking. So now can safelly shut off a bit the HW tracking, or
at least this case that makes us to depend on other drivers.
v2: Update commit message since this patch by itself doesn't solve
the bugzilla entries.
v3: Another attempt to improve commit message.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau damien.lespiau@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ultimate goal here is to remove the dependency we
currently have on audio driver power to get PSR working.
Since with audio driver runtime PM disabled the Hardware tracking
believes graphics is fully active and prevent PSR Entry, or
in other words continuously exit PSR.
So, the idea is to transfer the PSR exit responsability
from the HW tracking to the SW tracking (frontbuffer tracking),
who is really mature right now.
However with LPSP masked out there might be cases where we could
miss exit from HW tracking since it can be relying on this,
like a specific case reported at our mailing list who
user reported he would miss screen updates if scrolling firefox
in a Gnome environment when i915 runtimepm was enabled.
So before masking out LPSP again to make us independent from
the audio driver we need to make sure that all our cases
are coverred from the frontbuffer tracking perspective,
where the flush means invalidate and flush.
Without this patch for HSW, BDW and SKL we just do the
invalidate part when the flush wasn't originated by a page flip
because we were trusting the HW tracking for the flip case.
So let's rely more on frontbuffer tracking and do the
invalidation regardless the origin as expected for all platforms.
v2: Improve commit message as suggested by Paulo.
v3: Another attempt to let commit message more clear.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau damien.lespiau@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit (89251b17) intended to remove this line and let only one
DP_PSR_EN_CFG set, but it was wrong and this call is now duplicated
at the code.
Also "& ~DP_PSR_MAIN_LINK_ACTIVE" doesn't do anything at all. It
was like that since I introduced this call but probably the idea
was to be informative and make clear statement that we were not using
the link standby. So it is better to remove this one here and let
the code a bit cleaner.
v2: Improve commit message as requested by Paulo.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau damien.lespiau@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit e9f24d5fb7
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Mon Oct 5 13:26:36 2015 +0100
drm/i915: Clean up associated VMAs on context destruction
Added a warning based on an incorrect assumption that all VMAs
in a VM will be on the inactive list at the point last reference
to a context and VM is dropped.
This is not true because i915_gem_object_retire__read will not
put VMA on the inactive list until all activities on the object
in question (in all VMs) have been retired.
As a consequence, whether or not a context/VM will be destroyed
with its VMAs still on the active list, can depend on completely
unrelated activities using the same object from a different
context or engine.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92638
Testcase: igt/gem_request_retire/retire-vma-not-inactive
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448025816-25584-1-git-send-email-tvrtko.ursulin@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we experience a refcounting failure in a power domain/well (unref'ing at
least one too many times), log the name of the offending domain or well.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448034934-11926-2-git-send-email-daniels@collabora.com
Let us print human-parseable values from the power domain code; upcoming
display code also wants to use it.
This requires moving it out of i915_debugfs.c, as that is only conditionally
compiled.
v2: Move it out of the header.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448034934-11926-1-git-send-email-daniels@collabora.com
During suspend-to-idle we need to keep the DMC firmware active and DC6
enabled, since otherwise we won't reach deep system power states like
PC9/10. The lead for this came from Nivedita who noticed that the
kernel's turbostat tool didn't report any PC9/10 residency change
across an 'echo freeze > /sys/power/state'.
Reported-by: Nivedita Swaminathan <nivedita.swaminathan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447860750-18110-1-git-send-email-imre.deak@intel.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Merge slub bulk allocator updates from Andrew Morton:
"This missed the merge window because I was waiting for some repairs to
come in. Nothing actually uses the bulk allocator yet and the changes
to other code paths are pretty small. And the net guys are waiting
for this so they can start merging the client code"
More comments from Jesper Dangaard Brouer:
"The kmem_cache_alloc_bulk() call, in mm/slub.c, were included in
previous kernel. The present version contains a bug. Vladimir
Davydov noticed it contained a bug, when kernel is compiled with
CONFIG_MEMCG_KMEM (see commit 03ec0ed57f: "slub: fix kmem cgroup
bug in kmem_cache_alloc_bulk"). Plus the mem cgroup counterpart in
kmem_cache_free_bulk() were missing (see commit 033745189b "slub:
add missing kmem cgroup support to kmem_cache_free_bulk").
I don't consider the fix stable-material because there are no in-tree
users of the API.
But with known bugs (for memcg) I cannot start using the API in the
net-tree"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slab/slub: adjust kmem_cache_alloc_bulk API
slub: add missing kmem cgroup support to kmem_cache_free_bulk
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
slub: optimize bulk slowpath free by detached freelist
slub: support for bulk free with SLUB freelists
Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve
some reported problems.
All have been in linux-next, full details are in the shortlog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZSCjgACgkQMUfUDdst+yl4kQCgyYYsaVVUcG2i3HQUpio4CAJg
EFQAn03Z0OD/EGNHKw7FtsICSgAhSatG
=JRcn
-----END PGP SIGNATURE-----
Merge tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve
some reported problems.
All have been in linux-next, full details are in the shortlog below"
* tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: export fsl8250_handle_irq
serial: 8250_mid: Add missing dependency
tty: audit: Fix audit source
serial: etraxfs-uart: Fix crash
serial: fsl_lpuart: Fix earlycon support
bcm63xx_uart: Use the device name when registering an interrupt
tty: Fix direct use of tty buffer work
tty: Fix tty_send_xchar() lock order inversion
Here are some staging and iio driver fixes for 4.4-rc2. All of these
are in response to issues that have been reported and have been in
linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZSCfgACgkQMUfUDdst+yn0cwCeI7I/i1MUaiequc4gSOoElqfa
RCYAnj+PTk+BcbACs0mgZKbYuEEd1eVT
=nUNA
-----END PGP SIGNATURE-----
Merge tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are some staging and iio driver fixes for 4.4-rc2. All of these
are in response to issues that have been reported and have been in
linux-next for a while"
* tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: wilc1000: coreconfigurator: Drop unneeded wrapper functions"
iio: adc: xilinx: Fix VREFN scale
iio: si7020: Swap data byte order
iio: adc: vf610_adc: Fix division by zero error
iio:ad7793: Fix ad7785 product ID
iio: ad5064: Fix ad5629/ad5669 shift
iio:ad5064: Make sure ad5064_i2c_write() returns 0 on success
iio: lpc32xx_adc: fix warnings caused by enabling unprepared clock
staging: iio: select IRQ_WORK for IIO_DUMMY_EVGEN
vf610_adc: Fix internal temperature calculation
Here are a number of USB fixes and new device ids for 4.4-rc2. All have
been in linux-next and the details are in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZSDW4ACgkQMUfUDdst+ymrlwCgha5PobWYrhVnhC/w5ODZxRaF
oAQAn2tOK94L9sADvjbQlFUy+/Zaxxbj
=x9f4
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes and new device ids for 4.4-rc2. All
have been in linux-next and the details are in the shortlog"
* tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
usblp: do not set TASK_INTERRUPTIBLE before lock
USB: MAINTAINERS: cxacru
usb: kconfig: fix warning of select USB_OTG
USB: option: add XS Stick W100-2 from 4G Systems
xhci: Fix a race in usb2 LPM resume, blocking U3 for usb2 devices
usb: xhci: fix checking ep busy for CFC
xhci: Workaround to get Intel xHCI reset working more reliably
usb: chipidea: imx: fix a possible NULL dereference
usb: chipidea: usbmisc_imx: fix a possible NULL dereference
usb: chipidea: otg: gadget module load and unload support
usb: chipidea: debug: disable usb irq while role switch
ARM: dts: imx27.dtsi: change the clock information for usb
usb: chipidea: imx: refine clock operations to adapt for all platforms
usb: gadget: atmel_usba_udc: Expose correct device speed
usb: musb: enable usb_dma parameter
usb: phy: phy-mxs-usb: fix a possible NULL dereference
usb: dwc3: gadget: let us set lower max_speed
usb: musb: fix tx fifo flush handling
usb: gadget: f_loopback: fix the warning during the enumeration
usb: dwc2: host: Fix remote wakeup when not in DWC2_L2
...
Pull MIPS fixes from Ralf Baechle:
- Fix a flood of annoying build warnings
- A number of fixes for Atheros 79xx platforms
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ath79: Add a machine entry for booting OF machines
MIPS: ath79: Fix the size of the MISC INTC registers in ar9132.dtsi
MIPS: ath79: Fix the DDR control initialization on ar71xx and ar934x
MIPS: Fix flood of warnings about comparsion being always true.
