* Add ide_device_add() helper and convert host drivers to use it
instead of open-coded variants.
* Make ide_pci_setup_ports() and do_ide_setup_pci_device()
take 'u8 *idx' argument instead of 'ata_index_t *index'.
* Remove no longer needed ata_index_t.
* Unexport probe_hwif_init() and make it static.
* Unexport ide_proc_register_port().
There should be no functionality changes caused by this patch
(sgiioc4.c: ide_proc_register_port() requires hwif->present
to be set and it won't be set if probe_hwif_init() fails).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA. Then remove no longer needed hwif->atapi_dma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt34x.c: disable DMA masks for HPT345
(hwif->autodma is zero so DMA won't be enabled anyway).
* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
(hwif->autodma is zero so DMA won't be enabled anyway).
* Check noautodma global variable instead of drive->autodma in ide_tune_dma().
This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.
* Remove hwif->autodma (it was not checked by IDE core code anyway) and
drive->autodma (was set by all host drivers - except HPT345/TRM290 special
cases - unless "ide=nodma" was used).
While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
(this setting was always later over-ridden by host drivers anyway)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide-pmac allows separate PIO and DMA timings, and ide-pmac always sets
->autotune this change shouldn't have any other effect than bringing ide-pmac
driver in-line with other host drivers wrt ->ide_dma_check implementation.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.
* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program
the host for the transfer mode after programming the device. Set it
in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
and via82cxxx host drivers.
* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
skip programming of host/device for the transfer mode ("smart" hosts).
Set it in it821x host driver and check it in ide_tune_dma().
* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
direct ->set_pio_mode/->speedproc users to use these helpers.
* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
methods to callers.
* Rename ->speedproc method to ->set_dma_mode, make it void and update
all implementations accordingly.
* Update ide_set_xfer_rate() comments.
* Unexport ide_config_drive_speed().
v2:
* Fix issues noticed by Sergei:
- export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
to setting DMA modes from sc1200_set_pio_mode() to do_special()
- check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
- check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
- check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
- return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
- don't set ->set_{pio,dma}_mode on it821x in "smart" mode
- fix build problem in pmac.c
- minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
- improve patch description
Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
the device (not really an issue since 0x00 is not supported correctly by
any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add missing initialization of hwif->autodma and drive->autodma to
pmac_ide_setup_dma().
* Use ide_tune_dma() in pmac_ide_dma_check().
While at it:
* Fix pmac_ide_dma_check() return value if DMA mode is not programmed
(should be "-1" otherwise ide_set_dma() will try to enable DMA).
* Remove unnecessary drive->using_dma fiddling (->dma_off_quietly is always
called before ide_set_dma() call and ide_set_dma() calls ->ide_dma_on if
->ide_dma_check returns "0").
v2:
* No reason to blacklist all ide_floppy devices and the old code was always
enabling DMA anyway (without even programming controller/device if the
device was ide_floppy).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_config_drive_speed() instead of pmac_ide_do_setfeature() and remove
the latter, also ide-iops.c::__ide_wait_stat() could be static again.
Since for IDE PMAC host driver IDE_CONTROL_REG is always true, device's
->quirk_list is always zero and ->ide_dma_host_{on,off} are nops than
the only changes in behavior are:
* if PIO mode is set then ->dma_off_queitly is called to disable DMA
* if setting transfer mode fails ide_dump_status() is called to dump status
v2:
* IDE PMAC controllers allow separate PIO and DMA timings and PPC userland
depends on this fact, and calls "hdparm -p" without calling "hdparm -d".
Therefore to compensate for DMA being disabled by ide_config_drive_speed()
for PIO modes:
- add IDE_HFLAG_SET_PIO_MODE_KEEP_DMA flag and set it in PMAC host driver
- add handling of the new flag to ide-io.c::do_special()
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Upper layers are responsible for controlling nIEN so don't clear nIEN after
command execution in pmac_ide_do_setfeature().
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use __ide_wait_stat() instead of wait_for_ready() in pmac_ide_do_setfeature().
While at it do following changes to match __ide_wait_stat() call in
ide_config_drive_speed():
* Wait WAIT_CMD time (20 sec) instead of 2 sec for device to clear BUSY_STAT.
* Check DRQ_STAT bit (shouldn't be set for good device status).
Also remove no longer needed wait_for_ready() from ide-iops.c.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't check for good device status before executing the command in
pmac_ide_do_setfeature() (ide_config_drive_speed() doesn't do this).
It is a job of upper layers to guarantee that the device is ready to
accept new command before we get here.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix pmac_ide_dma_check() to use pmac_ide_tune_chipset() and remove no longer
necessary pmac_ide_{m,u}dma_enable().
* While at it remove some dead code from pmac_ide_dma_check() (leftovers from
conversion to use ide_max_dma_mode()).
There should be no functionality changes caused by this patch.
v2:
* Fix compile by replacing "id" with "drive->id" in pmac_ide_dma_check()
(Noticed by Ben).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
pmac_ide_do_setfeature() contains matching nIEN setting/clearing so this
Device Control register messing in pmac_ide_dma_check() is totally unnecessary.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move adjusting of cycle time for devices providing explicit DMA cycle time
from pmac_ide_mdma_enable() to set_timings_mdma().
* Remove no longer needed drive_cycle_time argument.
* BUG() if unsupported speed argument value is passed (shouldn't happen).
* Matching access/recovery timings always exist so remove redundant check.
* Make set_timings_mdma() void.
* Update pmac_ide_tune_chipset()'s comment.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't check check for pmif == NULL (it should never be NULL if we got here).
* Make a local copy of the timings and set the pmif->timings[] only after
setting the transfer mode on the device (otherwise SELECT_DRIVE() call in
pmac_ide_do_setfeature() will program new timings before the transfer mode
is set on the device - this was pointed out by Sergei). This change makes
pmac_ide_tune_chipset() behavior match this of pmac_ide_{m,u}dma_enable().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
kauai_lookup_timing() should always return non-zero return value:
* BUG() in kauai_lookup_timing() if the timing info cannot be found.
* Remove code checking for zero return value from all callers.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.
v2:
* Fix pmac_ide_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add { 0, 0 } entry to {kauai,shasta}_pio_timings[] so kauai_lookup_timing()
always returns a valid PIO timing (fixes PIO timing not being set for devices
with minimum PIO cycle <= 120ns).
* Add setting transfer mode on the device to pmac_ide_set_pio_mode().
* Fix pmac_ide_set_pio() to always program chipset for given PIO timing instead
of only when the device we want to program PIO timing for is the currently
selected one.
* Now that pmac_ide_set_pio() is fixed there is no need to set transfer mode
on the device and program chipset for PIO in pmac_ide_tune_chipset()
(returning 0 == success is not entirely correct but is OK for now since
the upper layers are only checking ->speedproc return value for DMA modes).
v2:
* s/speed/XFER_PIO_0 + pio/ in pmac_ide_set_pio_mode() so it actually compiles.
* Removal of kauai_lookup_timing() return value checking went to separate patch.
v3:
* Use XFER_PIO_0 not XFER_PIO. (Noticed by Ben)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_rate_filter() calls from host drivers to IDE core.
* Make ide_rate_filter() static.
* Make 'speed' argument of ->speedproc const.
v2:
* Fix it8213_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix icside, cris-ide, au1xxx-ide, amd74xx, via82cxxx and pmac host drivers
to use ide_rate_filter().
This results in the following modes (from user requests) being clipped down:
- invalid modes (values 0x46-0xFF) [ for all hosts ]
- unsupported by a host UDMA modes [ for hosts which support UDMA]
- all UDMA modes and MWDMA3-4 modes [ for hosts which don't support UDMA ]
- invalid modes (values 0x25-0x39) [ for hosts which don't support UDMA ]
* Host driver specific changes in behavior:
icside:
- no change
cris-ide
- clip unsupported UDMA3-6 modes down
- fix BUG() on trying to set unsupported UDMA3-6 modes
au1xxx-ide/pmac
- clip unsupported UDMA modes down
amd74xx/via82cxxx
- clip unsupported UDMA modes down
- fix random PIO timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* While at it remove no longer needed checks from pmac.c driver.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The PCI device table in the powermac IDE driver isn't properly
terminated. Depending on how your kernel is linked and other random
factors, you can end up with this driver matched against any other PCI
device in your system, possibly crashing at boot.
Thanks to Heikki for tracking this down with me, the bug have been there
for some time, though it rarely hurts due to luck. In this case, the
switch from .22 to .23-rc9 is causing it to show up due to differences
in the resulting layout of .data I suppose.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <pmac@au1.ibm.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pmac_ide_tune_chipset() don't set drive->init_speed.
Fix it by setting drive->{current,init}_speed in pmac_ide_do_setfeature()
and clean up pmac_ide_{tune_chipset,mdma_enable,udma_enable}().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ATA_PIO[0-6] defines to <linux/ata.h>.
* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.
* Add PIO masks to host drivers.
<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
and convert all users accordingly.
* Remove no longer needed ide_pio_data_t.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_pio_cycle_time() helper.
* Use it in ali14xx/ht6560b/qd65xx/cmd64{0,x}/sl82c105 and pmac host drivers
(previously cycle time given by the device was only used for "pio" == 255).
* Remove no longer needed ide_pio_data_t.cycle_time field.
v2:
* Fix "ata_" prefix (Noticed by Jeff).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter. Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.
Next patches add automatic detection of some systems using short cables.
Changes:
* Rename hwif->udma_four to hwif->cbl and make it u8.
* Convert all existing users accordingly (use ATA_CBL_* defines while at it).
* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().
* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
ide-timing.h:
* remove handling of DMA modes from ide_find_best_mode() and rename it to
ide_find_best_pio_mode()
* drop no longer needed "map" argument from ide_find_best_pio_mode()
and delete needless ->id check
* remove no longer needed XFER_SWDMA and XFER_UDMA* defines
au1xxx-ide.c:
* use ide_max_dma_mode() instead of ide_find_best_mode()
* remove needless CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA #ifdef
amd74xx.c:
* store UDMA masks in amd_ide_chip[] and while at it make "base" field
to be u8 instead of unsigned long
* convert the driver to use UDMA masks from amd_ide_chip[]
* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
of ide_find_best_mode()
* delete stale comment from amd74xx_ide_dma_check()
* remove no longer needed AMD_UDMA* defines
via82cxxx.c:
* remove unused DISPLAY_VIA_TIMINGS define
* store UDMA masks in via_isa_bridges[] and while at it make "flags" field
to be u8 instead of u16
* convert the driver to use UDMA masks from via_isa_bridges[]
* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
of ide_find_best_mode()
* remove no longer needed VIA_UDMA* defines
pmac.c:
* use ide_max_dma_mode() instead of ide_find_best_mode()
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Since ide_dma_timeout() method's result is discarded, make it return 'void'.
While at it, drop 'ide_' from the method's name, drop the '__' prefix from
the default method's name, and do some cleanups in this method driver-wise:
- in ide-dma.c, au1xxx-ide.c, and pdc202xx_old.c, define/use 'hwif' variable;
- in au1xxx-ide.c, get rid of commented out printk();
- in sl82c105.c, get rid of unnecessary variables.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide_dma_lostirq() method's result is discarded, make it return 'void'.
While at it, rename the method to dma_lost_irq(), drop the '__' prefix from the
default method's name, and do some cleanups in this method driver-wise:
- in aec62xx.c, rename the method in accordance with other drivers, and get rid
of unnecessary variables there;
- in pdc202xx_old.c, define/use 'hwif' variable;
- in sgiioc4.c, rearrange the code to call the resetproc() method directly.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* create_proc_ide_interfaces() tries to add /proc entries for every probed
and initialized IDE port, replace it by ide_proc_register_port() which does
it only for the given port (also rename destroy_proc_ide_interface() to
ide_proc_unregister_port() for consistency)
* convert {create,destroy}_proc_ide_interface[s]() users to use new functions
* pmac driver depended on proc_ide_create() to add /proc port entries, fix it
* au1xxx-ide, swarm and cs5520 drivers depended indirectly on ide-generic
driver (CONFIG_IDE_GENERIC=y) to add port /proc entries, fix them
* there is now no need to add /proc entries for IDE ports in proc_ide_create()
so don't do it
* proc_ide_create() needs now to be called before drivers are probed - fix it,
while at it make proc_ide_create() create /proc "ide" directory
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix breakage added in the IDE devel tree.
Add header, then fix
drivers/ide/ppc/pmac.c: In function `pmac_ide_setup_dma':
drivers/ide/ppc/pmac.c:2044: warning: assignment from incompatible pointer type
drivers/ide/ppc/pmac.c: In function `pmac_ide_dma_host_on':
drivers/ide/ppc/pmac.c:1989: warning: control reaches end of non-void function
include/linux/pci.h: In function `pmac_ide_init':
drivers/ide/ppc/pmac.c:1563: warning: ignoring return value of `pci_register_driver', declared with attribute warn_unused_result
Then add some apparently-long-missing error handling.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_host_on is called either when drive->using_dma == 1
or when return value is discarded make it void, also drop "ide_" prefix
* make __ide_dma_host_on() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_on() to atiixp_dma_host_on()
and sgiioc4_ide_dma_host_on() to sgiioc4_dma_host_on().
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_{host_off,off_quietly} always return '0'
make these functions void and while at it drop "ide_" prefix
* fix comment for __ide_dma_off_quietly()
* make __ide_dma_{host_off,off_quietly,off}() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_off() to atiixp_dma_host_off(),
sgiioc4_ide_dma_{host_off,off_quietly}() to sgiioc4_dma_{host_off,off_quietly}()
and sl82c105_ide_dma_off_quietly() to sl82c105_dma_off_quietly()
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All users of ->mmio == 1 are gone so convert ->mmio into flag.
Noticed by Alan Cox.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Small driver suspend() fixes in preparation for the PRETHAW events:
- Only compare message events for equality against PM_EVENT_* codes;
not against integers, or using greater/less-than comparisons.
(PM_EVENT_* should really become a __bitwise thing.)
- Explicitly test for SUSPEND events (rather than not-something-else)
before suspending devices.
- Removes more of the confusion between a pm_message_t (wraps event code)
and a "state" ... suspend() originally took a target system state.
These updates are correct and appropriate even without new PM_EVENT codes.
benh: "I think in the Mesh case, we should handle the freeze case as well or
we might get wild DMA."
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Greg KH <greg@kroah.com>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like a workaround for old bogus OF bitrot... This fixes it and
hence fixes boot on some performa machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
powermac platform & macintosh driver changes.
Built for pmac32_defconfig, g5_defconfig
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the old pmac ide led blink code and
adds generic LED subsystem support for the LED.
It maintains backward compatibility with the old
BLK_DEV_IDE_PMAC_BLINK Kconfig option which now
simply selects the new code and influences the
default trigger.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It looks like the generic ide code now wants ide_init_hwif_ports() to set
the parent struct device into the ide_hw structure (new field ?). Without
this, the mac ide code can cause the ide probing code to explode in flames
in sysfs registration due to what looks like a stale pointer in there
(happens when removing/re-inserting one of the hotswap media bays on some
laptops).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental ! There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
From: Thibaut VARENE <T-Bone@parisc-linux.org>
Cleaning up the hwif without knowing its previous state in pmac.c is a big
and potentially dangerous job, and there seems to be no generic code interface
that would provide either a way to properly release an hwif or to clean it up.
Fixes OOPS for empty PMAC interface and add-on PCI controller.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Enablement patch for the new PowerBooks (late 2005 edition).
This enables the ATA controller, Gigabit ethernet and basic AGP setup.
Bluetooth works out-of-the box after running hid2hci.
Still remaining is to get the touchpad to work, the simple change of just
adding the new USB ids isn't enough.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerBook HD led code uses obsoletes device-tree accessors which do
not work anymore for getting the root of the tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here is a new patch that removes all notion of the pmac, prep,
chrp and openfirmware initialization sections, and then unifies
the sections.h files without those __pmac, etc, sections identifiers
cluttering things up.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix remaining bits of u32 vs. pm_message confusion. Should not break
anything.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the usage of struct of_match to struct of_device_id,
similar to pci_device_id. This allows a device table to be generated,
which can be parsed by depmod(8) to generate a map file for module
loading.
In order for hotplug to work with macio devices, patches to
module-init-tools and hotplug must be applied. Those patches are
available at:
ftp://ftp.suse.com/pub/people/jeffm/linux/macio-hotplug/
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes CONFIG_PMAC_PBOOK (PowerBook support). This is now
split into CONFIG_PMAC_MEDIABAY for the actual hotswap bay that some
powerbooks have, CONFIG_PM for power management related code, and just left
out of any CONFIG_* option for some generally useful stuff that can be used
on non-laptops as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed an occasional crash on wakeup from sleep on my powerbook
(strangly never happened before, probably timing related) that appears to
be due to a dangling interrupt while the chip is put to sleep and beeing
reset on wakeup.
This patch fixes is by disabling the irq in the ide pmac driver while
asleep and only re-enable it after the chip has been fully reset. This is
safe to do so as the interrupt of these apple IDE cells is never shared.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
