Do not support mmap in S/PDIF mode. In S/PDIF mode
the buffer has to be copied, to allow the channel status
bits insertion.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191104133654.28750-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When ASoC card instance is removed containing a HDA codec,
hdac_hda_codec_remove() may run in parallel with codec resume.
This will cause problems if the HDA link is freed with
snd_hdac_ext_bus_link_put() while the codec is still in
middle of its resume process.
To fix this, change the order such that pm_runtime_disable()
is called before the link is freed. This will ensure any
pending runtime PM action is completed before proceeding
to free the link.
This issue can be easily hit with e.g. SOF driver by loading and
unloading the drivers.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101170635.26389-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
max98090 spec states that chip needs to be in turned-on state to supply
mic bias. Enable SHDN dapm widget along with MICBIAS widget to
actually turn on mic bias for proper headset button detection.
This is similar to cht_ti_jack_event in
sound/soc/intel/boards/cht_bsw_max98090_ti.c.
Note that due to ts3a227e reports the jack event right away before the
notifier is registered, if headset is plugged on boot, headset button
will not get detected until headset is unplugged and plugged. This is
still an issue to be fixed.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Link: https://lore.kernel.org/r/20191028095229.99438-1-cychiang@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When non standard names are used it is possible that one of the directions
are not provided, thus the flags needs to be present to tell the core that
we have half duplex setup.
Fixes: 642aafea88 ("ASoC: ti: remove compat dma probing")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191028115207.5142-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the implementation of sof_set_get_large_ctrl_data() there is a memory
leak in case an error. Release partdata if sof_get_ctrl_copy_params()
fails.
Fixes: 54d198d501 ("ASoC: SOF: Propagate sof_get_ctrl_copy_params() error properly")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20191027215330.12729-1-navid.emamdoost@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the implementation of sof_dfsentry_write() memory allocated for
string is leaked in case of an error. Go to error handling path if the
d_name.name is not valid.
Fixes: 091c12e1f5 ("ASoC: SOF: debug: add new debugfs entries for IPC flood test")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20191027194856.4056-1-navid.emamdoost@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We are missing the 'CONFIG_' prefix when using the kernel configure item
SND_SOC_SOF_HDA_ALWAYS_ENABLE_DMI_L1, here correct them.
Fixes: 43b2ab9009 ('ASoC: SOF: Intel: hda: Disable DMI L1 entry during capture')
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191025221538.6668-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devm conversion of kirkwood was incorrect; on removal, devm takes
effect after the "remove" function has returned. So, the effect of
the conversion was to change the order during remove from:
- snd_soc_unregister_component() (unpublishes interfaces)
- clk_disable_unprepare()
- cleanup resources
After the conversion, this became:
- clk_disable_unprepare() - while the device may still be active
- snd_soc_unregister_component()
- cleanup resources
Hence, it introduces a bug, where the internal clock for the device
may be shut down before the device itself has been shut down. It is
known that Marvell SoCs, including Dove, locks up if registers for a
peripheral that has its clocks disabled are accessed.
Fixes: f98fc0f815 ("ASoC: kirkwood: replace platform to component")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1iNGyP-0004oN-BA@rmk-PC.armlinux.org.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently each SSI unit's busif dma address is calculated by
following calculation formula:
0xec540000 + 0x1000 * id + busif / 4 * 0xA000 + busif % 4 * 0x400
But according to R-Car3 HW manual 41.1.4 Register Configuration,
ssi9 4/5/6/7 busif data register address
(SSI9_4_BUSIF/SSI9_5_BUSIF/SSI9_6_BUSIF/SSI9_7_BUSIF)
are out of this rule.
This patch updates the calculation formula to correct
ssi9 4/5/6/7 busif data register address.
Fixes: 5e45a6fab3 ("ASoc: rsnd: dma: Calculate dma address with consider of BUSIF")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[erosca: minor improvements in commit description]
Cc: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20191022185429.12769-1-erosca@de.adit-jv.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When our call to get the external clock fails, we forget to clean up
the enabled internal clock correctly. Enable the clock after we have
obtained all our resources.
Fixes: 84aac6c79b ("ASoC: kirkwood: fix loss of external clock at probe time")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1iNGyK-0004oF-6A@rmk-PC.armlinux.org.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Parameter fragments and fragment_size are type of u32. U32_MAX is
the correct check.
Signed-off-by: Xiaojun Sang <xsang@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191021095432.5639-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the PM8916 Hardware Register Description,
CDC_D_CDC_CONN_HPHR_DAC_CTL has only a single bit (RX_SEL)
to switch between RX1 (0) and RX2 (1). It is not possible to
disable it entirely to achieve the "ZERO" state.
However, at the moment the "RDAC2 MUX" mixer defines three possible
values ("ZERO", "RX2" and "RX1"). Setting the mixer to "ZERO"
actually configures it to RX1. Setting the mixer to "RX1" has
(seemingly) no effect.
Remove "ZERO" and replace it with "RX1" to fix this.
Fixes: 585e881e5b ("ASoC: codecs: Add msm8916-wcd analog codec")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191020153007.206070-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
All the kcontrol put() functions are currently returning 0 when
successful. This does not go well with alsamixer as it does
not seem to get notified on SND_CTL_EVENT_MASK_VALUE callbacks
when values change for (some of) the sof kcontrols.
This patch fixes that by returning true for volume, switch
and enum type kcontrols when values do change in put().
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191018123806.18063-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit below, adds a call to sysclk callback on shutdown.
This introduces a regression in stm32 SAI driver, as some clock
services are called twice, leading to unbalanced calls.
Move processing related to mclk from shutdown to sysclk callback.
When requested frequency is 0, assume shutdown and release mclk.
Fixes: 2458adb8f9 ("SoC: simple-card-utils: set 0Hz to sysclk when shutdown")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191018082040.31022-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
sof_audio_probe misses a check for devm_clk_get and may cause problems.
Add a check for it to fix the bug.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191017025044.31474-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike other format-related DAI parameters, rdai->bit_clk_inv flag
is not properly re-initialized when setting format for new stream
processing. The inversion, if requested, is then applied not to default,
but to a previous value, which leads to SCKP bit in SSICR register being
set incorrectly.
Fix this by re-setting the flag to its initial value, determined by format.
Fixes: 1a7889ca8a ("ASoC: rsnd: fixup SND_SOC_DAIFMT_xB_xF behavior")
Cc: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Cc: Jiada Wang <jiada_wang@mentor.com>
Cc: Timo Wischer <twischer@de.adit-jv.com>
Cc: stable@vger.kernel.org # v3.17+
Signed-off-by: Junya Monden <jmonden@jp.adit-jv.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20191016124255.7442-1-erosca@de.adit-jv.com
Signed-off-by: Mark Brown <broonie@kernel.org>
asoc_simple_debug_info and asoc_simple_debug_dai must be static
otherwise we might a compilation error if the compiler decides
not to inline the given function.
Fixes: 0580dde594 ("ASoC: simple-card-utils: add asoc_simple_debug_info()")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20191009153615.32105-3-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing MIX2 path on RX1/2 which take IIR1 and
IIR2 as inputs.
Without this patch sound card fails to intialize with below warning:
ASoC: no sink widget found for RX1 MIX2 INP1
ASoC: Failed to add route IIR1 -> IIR1 -> RX1 MIX2 INP1
ASoC: no sink widget found for RX2 MIX2 INP1
ASoC: Failed to add route IIR1 -> IIR1 -> RX2 MIX2 INP1
ASoC: no sink widget found for RX1 MIX2 INP1
ASoC: Failed to add route IIR2 -> IIR2 -> RX1 MIX2 INP1
ASoC: no sink widget found for RX2 MIX2 INP1
ASoC: Failed to add route IIR2 -> IIR2 -> RX2 MIX2 INP1
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191009111944.28069-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We can have 2 dcpm-s with the same backend and frontend name
(capture + playback pair), this causes the following debugfs error
on Intel Bay Trail systems:
[ 298.969049] debugfs: Directory 'SSP2-Codec' with parent 'Baytrail Audio Port' already present!
This commit adds a ":playback" or ":capture" postfix to the debugfs dir
name fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191005212202.5206-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If rockchip_pcm_platform_register() fails, e.g. upon deferring to wait
for an absent DMA channel, we return without disabling RPM, which makes
subsequent re-probe attempts scream with errors about the unbalanced
enable. Don't do that.
Fixes: ebb75c0bdb ("ASoC: rockchip: i2s: Adjust devm usage")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/bcb12a849a05437fb18372bc7536c649b94bdf07.1570029862.git.robin.murphy@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
User space always expects to be able to read ALSA controls, so ensure
no kcontrols are generated without an appropriate READ flag. In the case
of a read of such a control zeros will be returned.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191002084240.21589-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When removing sof module the support_button_press function will oops
because hp_jack pointer is not checked for NULL. So add a check to fix
this.
Signed-off-by: Jaska Uimonen <jaska.uimonen@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927201408.925-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When removing sof module the rt5682 jack handler will oops
if jack detection is not disabled. So add remove function,
which disables the jack detection.
Signed-off-by: Jaska Uimonen <jaska.uimonen@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927201408.925-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a known issue on some Intel platforms which causes
pause/release to run into xrun's during capture usecases.
The suggested workaround to address the issue is to
disable the entry of lower power L1 state in the physical
DMI link when there is a capture stream open.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
FW mailbox offset was not set before use and HDR size was not validated.
Fix this.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "snd_pcm_substream" handle was not initialized properly
in hda-loader.c for firmware load.
When the HDA DMAs were used to load the firmware,
the interrupts related to firmware load also triggered
calls to snd_sof_pcm_period_elapsed() on a non-existent ALSA
PCM stream.
This caused runtime kernel warnings from
pcm_lib.c:snd_pcm_period_elapsed().
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The old STOP sequence is: 1. stop DMA 2. send STOP ipc
If delay happen before the steps 1 and 2, the DMA buffer will be empty in
short time and cause pipeline xrun then stop the pipeline.
Then the step 2 ipc stop will return error as pipeline is already stopped.
Suggested change to avoid the issue is to switch the order of steps 1 and 2
for the stop sequence.
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a bug in sof_pcm_hw_free() where some cleanup actions were
skipped if STREAM_PCM_FREE IPC was already successfully sent to
DSP when the stream was stopped or suspended. This is incorrect
as hw_free should clean up also other resources, including pcm
lib page allocations, period elapsed work queue and call to
platform hw_free.
Fixes: c29d96c3b9b4 ("ASoC: SOF: reset DMA state in prepare")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We are using sof_parse_word_tokens() to parse tokens with
bool/byte/short/word tuple types, here add the missing check, to fix the
parsing failure at byte/bool tuple types.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When we fail to boot the firmware, we encounter a kernel oops in
hda_dsp_get_registers(), which is called conditionally in
hda_dsp_dump() when the sdev_>boot_complete flag is set.
Setting this flag _after_ dumping the data fixes the issue and does
not change the programming flow.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix potential NULL pointer dereference for alg_region in
wm_adsp_buffer_parse_legacy. In practice this can never happen as
loading the firmware should have failed at the wm_adsp2_setup_algs
stage, however probably better for the code to be robust against
future changes and this is more helpful for static analysis.
Signed-off-by: Li Xu <li.xu@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191001130911.19238-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Below Oops is caused in a system which uses ACPI instead of device node:
of_get_named_gpiod_flags: can't parse 'maxim,reset-gpio' property of node '(null)[0]'
BUG: kernel NULL pointer dereference, address: 0000000000000010
This patch avoids NULL pointer deferencing by adding a check before parsing
and initializes to make reset-gpio pin as invalid.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Link: https://lore.kernel.org/r/1569702150-11976-1-git-send-email-sathyanarayana.nujella@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "template.id" variable is an enum and in this context GCC will
treat it as an unsigned int so it can never be less than zero.
Fixes: 8a9782346d ("ASoC: topology: Add topology core")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190925110624.GR3264@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
There were a couple places where the return value wasn't assigned so the
error handling wouldn't trigger.
Fixes: 5c0769af4c ("ASoC: soc-dai: add snd_soc_dai_bespoke_trigger()")
Fixes: 95aef35533 ("ASoC: soc-dai: add snd_soc_dai_trigger()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190923142257.GB31251@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of WM1811 device there are currently being registered controls
referring to registers not existing on that device.
It has been noticed when getting values of "AIF1ADC2 Volume", "AIF1DAC2
Volume" controls was failing during ALSA state restoring at boot time:
"amixer: Mixer hw:0 load error: Device or resource busy"
Reading some registers through I2C was failing with EBUSY error and
indeed these registers were not available according to the datasheet.
To fix this controls not available on WM1811 are moved to a separate
array and registered only for WM8994 and WM8958.
There are some further differences between WM8994 and WM1811,
e.g. registers 603h, 604h, 605h, which are not covered in this patch.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20190920130218.32690-2-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure there is no OF node references kept when the driver
is removed/unbound.
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20190920130218.32690-3-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_DM365_VOICE_CODEC is a 'bool' option in a choice statement,
meaning it cannot be set to =m, but it selects two other drivers
that we may want to be loadable modules after all:
WARNING: unmet direct dependencies detected for SND_SOC_CQ0093VC
Depends on [m]: SOUND [=m] && !UML && SND [=m] && SND_SOC [=m]
Selected by [y]:
- SND_SOC_DM365_VOICE_CODEC [=y] && <choice>
Selected by [m]:
- SND_SOC_ALL_CODECS [=m] && SOUND [=m] && !UML && SND [=m] && SND_SOC [=m] && COMPILE_TEST [=y]
Add an intermediate symbol that sets SND_SOC_CQ0093VC and
MFD_DAVINCI_VOICECODEC to =m if SND_SOC=m.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190920075046.3210393-1-arnd@arndb.de
Signed-off-by: Mark Brown <broonie@kernel.org>
24 bits is supported in all modes and 16 bit only when the codec is slave
and the DAI is set to RIGHT_J.
Remove the unsupported sample format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190919071652.31724-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit a0a4bf57a9 ("ASoC: core: delete component->card_list in soc_remove_component only")
was trying to fix a kernel oops when list_del was called twice without
re-init the list. Use list_del_init() can solve it, too. Besides, it
will be more readable if we cleanup all component related resource at
soc_cleanup_component().
Suggested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20190918133131.15045-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI need to use rsnd_channel_normalization() for TDM-split mode,
thus, channel check need to do after that.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874l1aw39d.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A potential bug was reported in the email "[BUG] atmel_ssc_dai: a
possible sleep-in-atomic bug in atmel_ssc_shutdown"[1]
Indeed in the function atmel_ssc_shutdown() free_irq() was called in a
critical section protected by spinlock.
However this spinlock is only used in atmel_ssc_shutdown() and
atmel_ssc_startup() functions. After further analysis, it occurred that
the call to these function are already protected by mutex used on the
calling functions.
Then we can remove the spinlock which will fix this bug as a side
effect. Thanks to this patch the following message disappears:
"BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:909"
[1]: https://www.spinics.net/lists/alsa-devel/msg71286.html
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20190918100344.23629-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We add component->card_list in the end of soc_probe_component(). In
other words, component->card_list will not be added if there is an
error in the soc_probe_component() function. So we can't delete
component->card_list in the error handling of soc_probe_component().
Fixes: 22d1423187 ("ASoC: soc-core: add soc_cleanup_component()")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916210353.6318-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
EDMA requires the period size to be multiple of maxburst. Otherwise the
remaining bytes are not transferred and thus noise is produced.
We can handle this issue by adding a constraint on
SNDRV_PCM_HW_PARAM_PERIOD_SIZE to be multiple of tx/rx maxburst value.
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190913192807.8423-2-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is to allow machine drivers to set a certain bitclk rate
which might not be exactly rate * frame size.
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190830215910.31590-1-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All these functions declares and initializes variable ret with
'0' and without modifying 'ret' variable, it is returned.
This patch removes this redundancy and returns '0' directly.
Signed-off-by: Saiyam Doshi <saiyamdoshi.in@gmail.com>
Link: https://lore.kernel.org/r/20190909174541.GA22718@SD
Signed-off-by: Mark Brown <broonie@kernel.org>
