The SoundWire Linux devices are created purely based on information
provided by platform firmware (e.g. ACPI DSDT table). When the kernel
finds a matching driver for the device address (_ADR), the probe will
initialize required data structures and initialize pm ops.
When the SoundWire link is started at a later point, the physical
devices will synchronize on the SoundWire frames and report their
attachment status, thereby triggering the enumeration and
initialization of device registers.
This two-step solution was a conscious design decision to allow e.g. a
driver to use sideband mechanisms to turn power rails on. This can
also allow OEMs to describe multiple platforms with the same DSDT
table, the devices that are not physically present in hardware.
The drawback of this approach is a bit of confusion, with more devices
than are actually present in hardware. This results in 'ghost'
devices, for which the driver successfully probes, but that will not
generate any traffic on the bus. suspend-resume transitions are
handled by drivers, and skipped when the devices are not physically
present.
This patch provides a work-around for a second-level of confusion in
platform firmware: some platforms only use HDaudio links, but
nevertheless expose SoundWire 'ghost' devices. This results in error
messages in the Intel driver while trying to suspend/resume these
links. The simplest solution is to add a boolean status flag to skip
all suspend/resume/wake sequences if the link was never started.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210818024954.16873-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The power down sequence sets the link_up flag as false outside of the
mutex_lock. This is potentially unsafe.
In additional the flow in that sequence can be improved by first
testing if the link was powered, setting the link_up flag as false and
proceeding with the power down. In case the CPA bits cannot be
cleared, we only flag an error since we cannot deal with interrupts
any longer.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210818024954.16873-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Cadence IP exposes a small number of self-clearing bits in
the MCP_CONTROL and MCP_CONFIG_UPDATE registers.
We currently do not check that those bits are indeed cleared,
e.g. during resume operations. That could lead to resuming peripheral
devices too early.
In addition, if we happen to read these registers, update one of the
fields and write the register back, we may be writing stale data that
might have been cleared in hardware. These sort of race conditions
could lead to e.g. doing a hw_reset twice or stopping a clock that
just restarted. There is no clear way of avoiding these potential race
conditions other than making sure that these registers fields are
cleared before any read-modify-write sequence. If we detect this sort
of errors, we only log them since there is no clear recovery
possible. The only way out is likely to restart the IP with a
suspend/resume cycle.
Note that the checks are performed before updating the registers, as
well as after the Intel 'sync go' sequence in multi-link mode. That
should cover both the start and end of suspend/resume hardware
configurations. The Multi-Master mode gates the configuration updates
until the 'sync go' signal is asserted, so we only check on init and
after the end of the 'sync go' sequence.
The duration of the usleep_range() was defined by the GSYNC frequency
used in multi-master mode. With a 4kHz frequency, any configuration
change might be deferred by up to 250us. Extending the range to
1000-1500us should guarantee that the configuration change is
completed without any significant impact on the overall resume
time.
Suggested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714051349.13064-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that the auxiliary_bus exists, there's no reason to use platform
devices as children of a PCI device any longer.
This patch refactors the code by extending a basic auxiliary device
with Intel link-specific structures that need to be passed between
controller and link levels. This refactoring is much cleaner with no
need for cross-pointers between device and link structures.
Note that the auxiliary bus API has separate init and add steps, which
requires more attention in the error unwinding paths. The main loop
needs to deal with kfree() and auxiliary_device_uninit() for the
current iteration before jumping to the common label which releases
everything allocated in prior iterations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210511052132.28150-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cppcheck complains:
drivers/soundwire/intel.c:564:15: style: Variable 'link_control' is
assigned a value that is never used. [unreadVariable]
link_control = intel_readl(shim, SDW_SHIM_LCTL);
This looks like a leftover from a previous version, remove.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210302091122.13952-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We fixed a lot of warnings in 2019 but the magic of copy-paste keeps
adding new ones...
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210323005855.20890-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that we have declarations and bus support, add quirks for Intel
platforms.
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210302082720.12322-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
HP Spectre x360 Convertible devices expose invalid _ADR fields in the
DSDT, which prevents codec drivers from probing. A possible solution
is to override the DSDT, but that's just too painful for users.
This patch suggests a simple DMI-based quirk to remap the existing
invalid ADR information into valid ones.
BugLink: https://github.com/thesofproject/linux/issues/2700
Co-developed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210302075105.11515-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dev->power.runtime_error will be set to the return value of the runtime
suspend callback function, and runtime resume function will return
-EINVAL if dev->power.runtime_error is not 0.
Somehow the codec rarely doesn't return an ACK to the clock prepare
command. If we stop the runtime suspend process and return error, we
will not be able to resume again. Likewise, if the codec lost sync and
did not rejoin, the resume operation will also fail. As a result, the
SoundWire bus can not be used anymore.
This patch suggests to finish the runtime suspend process even if we fail
to stop sdw bus clock. In the case where we do a hardware reset, the codecs
will be reconfigured completely. In the case where we use the regular clock
stop, the codecs keep their state and worst case will fall off the bus and
reattach.
The only drawback is that the power consumption may be higher and
device-initiated interrupts may be lost, but at least audio function can
still work after resume.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210114030248.9005-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Without CONFIG_PM, there is another warning about an unused function:
drivers/soundwire/intel.c:530:12: error: 'intel_link_power_down' defined but not used [-Werror=unused-function]
After a previous fix, the driver already uses both an #ifdef and
a __maybe_unused annotation but still gets it wrong. Remove the
ifdef and instead use __maybe_unused consistently to avoid the
problem for good.
Fixes: f046b23340 ("soundwire: intel: fix intel_suspend/resume defined but not used warning")
Fixes: ebf878eddb ("soundwire: intel: add pm_runtime support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201203230502.1480063-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds debugfs support to override the Master and Slave data
modes. The settings only take effect prior to a new stream being
prepared/enabled, or on resume.
The test mode can be set to verify data integrity and detect bus
clashes, but can only be used to test capture paths. In this case the
input generated by a Slave source port is replaced by a fixed or
cyclical patterns.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200920193207.31241-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
FIELD_PREP() does not replace the bits so it is not apt in case where we
modify a register.
Use u32_replace_bits() or u16_replace_bits() instead.
Fixes: 3b4979cabd ("soundwire: intel: use FIELD_{GET|PREP}")
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200917120146.1780323-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This algorithm computes bus parameters like clock frequency, frame
shape and port transport parameters based on active stream(s) running
on the bus.
Developers can also implement their own .compute_params() callback for
specific resource management algorithm, and set if before calling
sdw_add_bus_master()
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah. All hard-coded
values were removed from the initial contribution to use BIOS
information instead.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200908131520.5712-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that the stream is handled at the dai-link level (in the machine
driver), we can remove the stream handling at the dai level. We still
need these callbacks to perform dai-level resource handling
(i.e. addition/removal of a master).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903204739.31206-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that the stream trigger is handled at the dai-link level, there is
no need for a dai-level trigger any longer.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903204739.31206-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
snd_soc_dai_get_sdw_stream() can only return the pointer to stream or
an ERR_PTR value, NULL is not a possible value.
Fixes: 09553140c8 ('soundwire: intel: implement get_sdw_stream() operations')
Reported-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903204739.31206-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
use FIELD_{GET|PREP} in intel driver to get/set field values instead of
open coding masks and shift operations.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903114504.1202143-8-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Each link has separate power controls, but experimental results show
we need to use an all-or-none approach to the link power management.
This change has marginal power impacts, the DSP needs to be powered
anyways before SoundWire links can be powered, and even when powered a
link can be in clock-stopped mode.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200901150556.19432-11-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Detect cases where the clock is assumed to be stopped but the IP is
not in the relevant state. There is no real way to recover here, but
adding an error log can help detect bad programming sequences or race
conditions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200901150556.19432-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Deal with the BUS_RESET case, which is the default. The only change is
to add support for the exit sequence using the syncArm/syncGo mode for
the exit reset sequence.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200901150556.19432-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The multi-link support is enabled with a hardware gsync signal
connecting all links. All commands and operations which typically are
handled on an SSP boundary will be deferred further and enabled across
all links with the 'syncGo' sequence.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200901150556.19432-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When CONFIG_PM_SLEEP is not defined, GCC throws compilation warnings:
drivers/soundwire/intel.c:1799:12: warning: ‘intel_resume’ defined but not
used [-Wunused-function]
static int intel_resume(struct device *dev)
^~~~~~~~~~~~
drivers/soundwire/intel.c:1683:12: warning: ‘intel_suspend’ defined but not
used [-Wunused-function]
static int intel_suspend(struct device *dev)
^~~~~~~~~~~~~
Fix by using __maybe_unused macro.
Suggested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200824133234.28115-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When all the links are suspended, the HDaudio controller may suspend
and the power rails to the SoundWire IP may be disabled, requiring a
complete re-initialization/enumeration on resume. However, if one or
more Masters remained active, the HDaudio controller will remain active
and the power rails will remain enabled. As a result, during the link
resume step we can check if the context was preserved by verifying if
the clock was stopped, and avoid doing a complete bus reset and
re-enumeration.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-13-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In this mode, on restart the bus restarts immediately, the Slaves
remain synchronized and all context is kept intact.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-12-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In case the clock needs to keep running, we need to prevent the Master
from entering pm_runtime suspend.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-10-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move existing pm_runtime suspend under the CLK_STOP_TEARDOWN case.
In this mode the Master IP will lose all context but in-band wakes are
supported.
On pm_runtime resume a complete re-enumeration will be performed after
a bus reset.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that we have options, add support for TEARDOWN mode (same
functionality as existing code)
All other modes will be added in follow-up patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add quirk and pm_runtime idle scheduling to let the Master suspend if
no Slaves become attached. This can happen when a link is not marked
as disabled and has devices exposed in the DSDT, if the power is
controlled by sideband means or the link includes a pluggable
connector.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .prepare() callback is invoked for normal streaming, underflows or
during the system resume transition. In the latter case, the context
for the ALH PDIs is lost, and the DSP is not initialized properly
either, but the bus parameters don't need to be recomputed.
Conversely, when doing a regular .prepare() during an underflow, the
ALH/SHIM registers shall not be changed as the hardware cannot be
reprogrammed after the DMA started (hardware spec requirement).
This patch adds storage of PDI and hw_params in the DAI dma context,
and the difference between the types of .prepare() usages is handled
via a simple boolean, updated when suspending, and tested for in the
.prepare() case.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This helps make sure they are all UNATTACHED and reset the state
machines.
At the moment we perform a bus reset both for system resume and
pm_runtime resume, this will be modified when clock-stop mode is
supported
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Previous patches took care of the case where the master device is
pm_runtime 'suspended' when a system suspend occurs.
In the case where the master device was not suspended, e.g. if suspend
occurred while streaming audio, Intel validation noticed a race
condition: the pm_runtime suspend may conflict with the enumeration
started by the system resume.
This can be simply fixed by updating the status before exiting system
resume.
GitHub issue: https://github.com/thesofproject/linux/issues/1482
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The system resume does the entire bus re-initialization and brings it
to full-power. If the device was pm_runtime suspended, there is no
need to run the pm_runtime resume sequence after the system runtime.
Follow the documentation from runtime_pm.rst, and conditionally
disable, set_active and re-enable the device on system resume.
Note that pm_runtime_suspended() is used instead of
pm_runtime_status_suspended() so that we can deal with the case where
pm_runtime is disabled.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add basic hooks in DAI .startup and .shutdown callbacks.
The SoundWire IP should be powered between those two calls. The power
dependencies between SoundWire and DSP are handled with the
parent/child relationship, before the SoundWire master device becomes
active the parent device will become active and power-up the shared
rails.
For now the strategy is to rely on complete enumeration when the
device becomes active, so the code is a copy/paste of the sequence for
system suspend/resume. In future patches, the strategy will optionally
be to rely on clock stop if the enumeration time is prohibitive or
when the devices connected to a link can signal a wake.
A module parameter is added to make integration of new Slave devices
easier, to e.g. keep the device active or prevent clock-stop.
Note that we need to we have to disable runtime pm before device
unregister, otherwise we will see "Failed to power up link: -11" error
on module remove test.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Implement suspend/resume capabilities (not runtime_pm for now)
The resume part is essentially a full-blown re-enumeration.
When S0ix is supported, we will select clock stop mode when the ACPI
target state is S0, and tear down the link for S3.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200721203723.18305-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This contains few core changes and bunch of Intel driver updates:
- Adds definitions for 1.2 spec
- Sanyog left as a MAINTAINER and Bard took his place while Sanyog
is a reviewer now.
- Intel: Lots of updates to stream/dai handling, wake support and link
synchronization.
-----BEGIN PGP SIGNATURE-----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=De+P
-----END PGP SIGNATURE-----
Merge tag 'soundwire-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next
Vinod writes:
soundwire updates for 5.9-rc1
This contains few core changes and bunch of Intel driver updates:
- Adds definitions for 1.2 spec
- Sanyog left as a MAINTAINER and Bard took his place while Sanyog
is a reviewer now.
- Intel: Lots of updates to stream/dai handling, wake support and link
synchronization.
* tag 'soundwire-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (31 commits)
Soundwire: intel_init: save Slave(s) _ADR info in sdw_intel_ctx
soundwire: intel: add wake interrupt support
soundwire: intel/cadence: merge Soundwire interrupt handlers/threads
soundwire: intel_init: use EXPORT_SYMBOL_NS
soundwire: intel_init: add implementation of sdw_intel_enable_irq()
soundwire: intel: introduce helper for link synchronization
soundwire: intel: introduce a helper to arm link synchronization
soundwire: intel: revisit SHIM programming sequences.
soundwire: intel: reuse code for wait loops to set/clear bits
soundwire: fix the kernel-doc comment
soundwire: sdw.h: fix indentation
soundwire: sdw.h: fix PRBS/Static_1 swapped definitions
soundwire: intel: don't free dma_data in DAI shutdown
soundwire: cadence: allocate/free dma_data in set_sdw_stream
soundwire: intel: remove stream allocation/free
soundwire: stream: add helper to startup/shutdown streams
soundwire: intel: implement get_sdw_stream() operations
MAINTAINERS: change SoundWire maintainer
soundwire: bus: initialize bus clock base and scale registers
soundwire: extend SDW_SLAVE_ENTRY
...
When system is suspended in clock stop mode on intel platforms, both
master and slave are in clock stop mode and soundwire bus is taken
over by a glue hardware. The bus message for jack event is processed
by this glue hardware, which will trigger an interrupt to resume audio
pci device. Then audio pci driver will resume soundwire master and slave,
transfer bus ownership to master, finally slave will report jack event
to master and codec driver is triggered to check jack status.
if a slave has been attached to a bus, the slave->dev_num_sticky
should be non-zero, so we can check this value to skip the
ghost devices defined in ACPI table but not populated in hardware.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code uses one pair of interrupt handler/thread per link
but at the hardware level the interrupt is shared. This works fine for
legacy PCI interrupts, but leads to timeouts in MSI (Message-Signaled
Interrupt) mode, likely due to edges being lost.
This patch unifies interrupt handling for all links. The dedicated
handler is removed since we use a common one for all shared interrupt
sources, and the thread function takes care of dealing with interrupt
sources. This partition follows the model used for the SOF IPC on
HDaudio platforms, where similar timeout issues were noticed and doing
all the interrupt handling/clearing in the thread improved
reliability/stability.
Validation results with 4 links active in parallel show a night-and-day
improvement with no timeouts noticed even during stress tests. Latency
and quality of service are not affected by the change - mostly because
events on a SoundWire link are throttled by the bus frame rate
(typically 8..48kHz).
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After arming the synchronization, the SYNCGO field controls the
hardware-based synchronization between links.
Move the programming and wait for clear of SYNCGO to dedicated helper.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move code from pre_bank_switch to dedicated helper, will be used in
follow-up patches as recommended by programming flows.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Somehow the existing code is not aligned with the steps described in
the documentation, refactor code and make sure the register
programming sequences are correct. Also add missing power-up,
power-down and wake capabilities (the last two are used in follow-up
patches but introduced here for consistency).
Some of the SHIM registers exposed fields that are link specific, and
in addition some of the power-related registers (SPA/CPA) take time to
be updated. Uncontrolled access leads to timeouts or errors. Add a
mutex, shared by all links, so that all accesses to such registers are
serialized, and follow a pattern of read-modify-write.
This includes making sure SHIM_SYNC is programmed only once, before
the first master is powered on. We use a 'shim_mask' field, shared
between all links and protected by a mutex, to deal with power-up and
power-down sequences.
Note that the SYNCPRD value is tied only to the XTAL value and not the
current bus frequency or the frame rate.
BugLink: https://github.com/thesofproject/linux/issues/1555
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that the DMA data is allocated/freed in set_sdw_stream(), remove
free operations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200630184356.24939-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To support streaming across multiple links, the stream allocation/free
needs to be at the dailink level, not the dai.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200630184356.24939-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is needed to retrieve the information when the stream is
allocated at the dai_link level.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200630184356.24939-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rather than a plain-vanilla init/exit, this patch provides 3 steps in
the initialization needed for driver selection, machine driver
selection and deal with power rail dependencies.
- ACPI scan: this step is done at a very early stage to detect the
presence of a SoundWire Controller and enabled links at the BIOS
level. This step may be called from the legacy HDaudio driver, which
will abort its probe to let the Sound Open Firmware (SOF) handle the
hardware.
- probe: this step allocates all the required memory and will add a
sdw_bus, which in turn will result in identifying all possible Slaves
listed below the Controller ACPI companion device. All the information
is reported to the parent PCI driver which will select the relevant
machine driver.
- startup: this last step starts the bus reset, which results in Slave
devices reporting as ATTACHED and being enumerated. This step is only
done during the card creation stage, after the DSP is powered to
account for internal power rail dependencies.
These 3 steps are already supported in the Sound Open firmware
drivers and upstream.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The use of drvdata mixes two structures. There was no harm the first
structure is embedded as the first element of the second, but that's
not good. Make sure all drvdata is based on the 'sdw_cdns' structure.
While we are at it, remove indirections for 'dev' and 'cdns' to make
the code more readable.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
