Make use of the newly introduced mii_bmcr_encode_fixed() to get the
BMCR value when setting loopback mode for the 88e1510.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per Errata Section 5.1, if EEE is intended to be used, some register
writes must be done once after every hardware reset. This patch now adds
the necessary register writes as listed in the Marvell errata.
Without this fix we experience ethernet problems on some of our boards
equipped with a new version of this ethernet PHY (different supplier).
The fix applies to Marvell Alaska 88E1510/88E1518/88E1512/88E1514
Rev. A0.
Signed-off-by: Leszek Polak <lpolak@arri.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Behún <kabel@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220516070859.549170-1-sr@denx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
With some SFP modules, such as Finisar FCLF8522P2BTL, the PHY hardware
strapping defaults to 1000BaseX mode, but the kernel prefers to set them
for SGMII mode. When this happens and the PHY is soft reset, the BMSR
status register is updated, but this happens after the kernel has already
read the PHY abilities during probing. This results in support not being
detected for, and the PHY not advertising support for, 10 and 100 Mbps
modes, preventing the link from working with a non-gigabit link partner.
When the PHY is being configured for SGMII mode, call genphy_read_abilities
again in order to re-read the capabilities, and update the advertising
field accordingly.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug resulted in only the current mode being resumed and suspended when
the PHY supported both fiber and copper modes and when the PHY only supported
copper mode the fiber mode would incorrectly be attempted to be resumed and
suspended.
Fixes: 3758be3dc1 ("Marvell phy: add functions to suspend and resume both interfaces: fiber and copper links.")
Signed-off-by: Kurt Cancemi <kurt@x64architecture.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220312201512.326047-1-kurt@x64architecture.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is mandatory for a software to issue a reset upon modifying RGMII
Receive Timing Control and RGMII Transmit Timing Control bit fields of MAC
Specific Control register 2 (page 2, register 21) otherwise the changes
won't be perceived by the PHY (the same is applicable for a lot of other
registers). Not setting the RGMII delays on the platforms that imply it'
being done on the PHY side will consequently cause the traffic loss. We
discovered that the denoted soft-reset is missing in the
m88e1121_config_aneg() method for the case if the RGMII delays are
modified but the MDIx polarity isn't changed or the auto-negotiation is
left enabled, thus causing the traffic loss on our platform with Marvell
Alaska 88E1510 installed. Let's fix that by issuing the soft-reset if the
delays have been actually set in the m88e1121_config_aneg_rgmii_delays()
method.
Cc: stable@vger.kernel.org
Fixes: d6ab933647 ("net: phy: marvell: Avoid unnecessary soft reset")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20220205203932.26899-1-Pavel.Parkhomenko@baikalelectronics.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When setting up autonegotiation for 88E1118R and compatible PHYs,
a software reset of PHY is issued before setting up polarity.
This is incorrect as changes of MDI Crossover Mode bits are
disruptive to the normal operation and must be followed by a
software reset to take effect. Let's patch m88e1118_config_aneg()
to fix the issue mentioned before by invoking software reset
of the PHY just after setting up MDI-x polarity.
Fixes: 605f196efb ("phy: Add support for Marvell 88E1118 PHY")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing genphy_loopback() is not applicable for Marvell PHY. Besides
configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control
Register), it is also required to configure same bits in Page 2
Register 21 (MAC Specific Control Register 2) according to speed of
the loopback is operating.
Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).
FIXME: Based on trial and error test, it seem 1G need to have delay between
soft reset and loopback enablement.
Fixes: 014068dcb5 ("net: phy: genphy_loopback: add link speed configuration")
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corentin Labbe reports that the SSI 1328 does not work when allowing
the PHY to operate at gigabit speeds, but does work with the generic
PHY driver.
This appears to be because m88e1118_config_init() writes a fixed value
to the MSCR register, claiming that this is to enable 1G speeds.
However, this always sets bits 4 and 5, enabling RGMII transmit and
receive delays. The suspicion is that the original board this was
added for required the delays to make 1G speeds work.
Add the necessary configuration for RGMII delays for the 88E1118 to
bring this into line with the requirements for RGMII support, and thus
make the SSI 1328 work.
Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502.
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use phy_write_paged() in m88e1118_config_init() to set the MSCR value.
We leave the other paged write for the LEDs in case the DT register
parsing is relying on this page.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add Wake-on-PHY feature support by enabling the Link Up Event.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SFP cages connected to the Marvell 88E1512 transceiver.
88E1512 supports for SGMII/1000Base-X/100Base-FX media type with RGMII
on system interface. Configure PHY to appropriate mode depending on the
type of SFP inserted. On SFP removal configure PHY to the RGMII-copper
mode so RJ-45 port can still work.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Link: https://lore.kernel.org/r/20210812134256.2436-1-i.bornyakov@metrotek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Switch statement is clearer than a group of 'if-else'.
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than open-coding the phy_modify_changed() sequence, use this
helper in marvell_set_polarity().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of PHYs support the PHY tunable to set and get
downshift. However, only 88E1116R enables downshift by default. Extend
this default enabled to all the PHYs that support the downshift
tunable.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add downshift support for 88E1240, it uses the same downshift
configuration registers as 88E1011.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Link: https://lore.kernel.org/r/20210428095356.621536-1-fido_max@inbox.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Changing downshift params without software reset has no effect,
so call genphy_soft_reset() after change downshift params.
As the datasheet says:
Changes to these bits are disruptive to the normal operation therefore,
any changes to these registers must be followed by software reset
to take effect.
Fixes: 5c6bc5199b ("net: phy: marvell: add downshift support for M88E1111")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing downshift params without software reset has no effect,
so call genphy_soft_reset() after change downshift params.
As the datasheet says:
Changes to these bits are disruptive to the normal operation therefore,
any changes to these registers must be followed by software reset
to take effect.
Fixes: 911af5e149 ("net: phy: marvell: fix downshift function naming")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This causes error reported by kernel test robot.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 41d26bf4ab ("net: phy: marvell: refactor HWMON OOP style")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Amethyst internal PHY.
The only difference from Peridot is HWMON.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the &= operator instead of
ret = ret & ...
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register 27_6.15:14 has the following description in 88E6393X
documentation:
Temperature Sensor Enable
0x0 - Sample every 1s
0x1 - Sense rate decided by bits 10:8 of this register
0x2 - Use 26_6.5 (One shot Temperature Sample) to enable
0x3 - Disable
This is compatible with how the 6390 code uses this register currently,
but the 6390 code handles it as two 1-bit registers (somewhat), instead
of one register with 4 possible values.
(A newer version of the 6390 documentation removed temperature sensor
section completely. In an older version, the above mentioned register
is reserved, although it is R/W. Since the code works, I think we can
assume that it is correct.)
Rename this register and define all 4 values according to 6393X
documentation.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a structure of Marvell PHY specific HWMON methods to reduce code
duplication. Store a pointer to this structure into the PHY driver's
driver_data member.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit fee2d54641 ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
PHY [...] driver [Marvell 88E6390] (irq=63)
And afterwards as:
PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: Pali Rohár <pali@kernel.org>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d54641 ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 88E1111 is operating in SGMII mode, auto-negotiation should be enabled
on the SGMII side so that the link will come up properly with PCSes which
normally have auto-negotiation enabled. This is normally the case when the
PHY defaults to SGMII mode at power-up, however if we switched it from some
other mode like 1000Base-X, as may happen in some SFP module situations,
it may not be, particularly for modules which have 1000Base-X
auto-negotiation defaulting to disabled.
Call genphy_check_and_restart_aneg on the fiber page to ensure that auto-
negotiation is properly enabled on the SGMII interface.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.
Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.
This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_read_status() is already the default for the .read_status() op.
Drop the unnecessary references.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Finisar FCLF8520P2BTL 1000BaseT SFP module uses a Marvel 88E1111 PHY
with a modified PHY ID. Add support for this ID using the 88E1111
methods.
By default these modules do not have 1000BaseX auto-negotiation enabled,
which is not generally desirable with Linux networking drivers. Add
handling to enable 1000BaseX auto-negotiation when these modules are
used in 1000BaseX mode. Also, some special handling is required to ensure
that 1000BaseT auto-negotiation is enabled properly when desired.
Based on existing handling in the AMD xgbe driver and the information in
the Finisar FAQ:
https://www.finisar.com/sites/default/files/resources/an-2036_1000base-t_sfp_faqreve1.pdf
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20201028171540.1700032-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixed spelling in comment like below:
s/defalut/default/p
This is in linux-next.
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201029095525.20200-1-unixbhaskar@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert m88e1318_get_wol() to use the well implemented phy_read_paged()
instead of open coding it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel in general does not use &func referencing format.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF_MDIO is set to be a module the code block is not
compiled. Use the IS_ENABLED macro that checks for both built in as
well as module.
Fixes: cf41a51db8 ("of/phylib: Use device tree properties to initialize Marvell PHYs.")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to call phy_restore_page() even if phy_select_page() fails.
Otherwise we are holding the phy_lock_mdio_bus() lock. This requirement
is documented at the start of the phy_select_page() function.
Fixes: a618e86da9 ("net : phy: marvell: Speedup TDR data retrieval by only changing page once")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing a TDR measurement for a short distance, the pulse
width should be low, to help differentiate between the outgoing pulse
and any reflection. For longer distances, the pulse should be wider,
to help with attenuation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting the TDR data requires a large number of MDIO bus
transactions. The number can however be reduced if the page is only
changed once. Add the needed locking to allow this, and make use of
unlocked read/write methods where needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PHYs can measure the amplitude of the returned signal for
a given distance. Implement this option of the cable test
infrastructure. When reporting the step, convert the distance into cm.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Step based on the measurement resolution, and convert this to cm.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PHYs have a couple of different register sets for
performing cable tests. Page 7 provides the simplest to use.
v3:
s/mavell/marvell/g
Remove include of <uapi/linux/ethtool_netlink.h>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The negotiation of flow control / pause frame modes was broken since
commit fcf1f59afc ("net: phy: marvell: rearrange to use
genphy_read_lpa()") moved the setting of phydev->duplex below the
phy_resolve_aneg_pause call. Due to a check of DUPLEX_FULL in that
function, phydev->pause was no longer set.
Fix it by moving the parsing of the status variable before the blocks
dealing with the pause frames.
As the Marvell 88E1510 datasheet does not specify the timing between the
link status and the "Speed and Duplex Resolved" bit, we have to force
the link down as long as the resolved bit is not set, to avoid reporting
link up before we even have valid Speed/Duplex.
Tested with a Marvell 88E1510 (RGMII to Copper/1000Base-T)
Fixes: fcf1f59afc ("net: phy: marvell: rearrange to use genphy_read_lpa()")
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that phylib notifies the user of a downshift we can remove
this functionality from the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't attempt to interpret the PHY specific status register unless
the PHY is indicating that the resolution is valid.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the helper to check and restart autonegotiation for the marvell
fiber page negotiation setting.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_modify_changed() to change the fiber advertisement register
rather than open coding this functionality.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use existing clause 37 advertising/link partner definitions rather than
private ones for the advertisement registers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
marvell_read_status_page_an() always reads the PHY status register, but
marvell_update_link() has already done this. Rather than wastefully
reading the register twice in quick succession, read it once in
marvell_read_status_page() and use the result for both.
This makes marvell_update_link() rather pointless, so move it into
marvell_read_status_page().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
