This allows the S3C CPUfreq driver to do DVFS.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A&W6410 board uses Samsung S3C6410 SoC and it is registered with 2183.
Framebuffer and ethernet devices are supported currently.
Unnecessary header file is removed.
Fix to use __raw_writel() and __raw_readl() for accessing mapped address.
Thank you for your comments.
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since no consumers are currently configured for the SMDK6410 mark all
the supplies on the board as being always_on, ensuring interoperability
with future regulator API changes to disable unused regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Using an active high IRQ ensures that the WM8350 interrupt handling
does not spin when used with a SMDK6410 which has not had R20 removed
and R21 fitted to connect EINT12 to the PMIC module rather thant the
fixed regulators on the CPU module.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is a basic support for NCP board based on s3c6410.
Only enables the serial. also remove empty i2c device.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The SMDK6410 supports pluggable PMIC boards. One such board is the
Wolfson Microelectronics 1190-EV1 for the WM8350 PMICs. This patch
introduces initial support for this module. Further patches will
add additional integration with the system as support for the
S3C6410 and other devices on the system improves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ensure that the LCD output type is RGB and that
the modem interface is not bypassing the LCD
block. This ensures the LCD interface output
gets to the pins in the correct format.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
arm is placing some code in the .text.init section, but it does not
reference that section in its linker scripts.
This change moves this code from the .text.init section to the
.init.text section, which is presumably where it belongs.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Symbols like SOFT_RESET are way too generic to be exported at large.
To avoid this, let's move the mbus bridge register defines into a
separate file and include it where needed. This affects mach-kirkwood,
mach-loki, mach-mv78xx0 and mach-orion5x simultaneously as they all
share code in plat-orion which relies on those defines.
Some other defines have been moved to narrower scopes, or simply deleted
when they had no user.
This fixes compilation problem with mpt2sas on the above listed
platforms.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a version incorporating Christoph's suggestion.
Separate out common *fstatat functionality into a single function
instead of duplicating it all over the code.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
From: David Brownell <dbrownell@users.sourceforge.net>
Fix GPIO-related build error on mach-imx platform:
CC drivers/spi/spi_gpio.o
In file included from /home/db/kernel/scratch/arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:7,
from drivers/spi/spi_gpio.c:23:
arch/arm/mach-imx/include/mach/gpio.h: In function 'imx_gpio_get_value':
arch/arm/mach-imx/include/mach/gpio.h:27: error: implicit declaration of function '__REG2'
arch/arm/mach-imx/include/mach/gpio.h:27: error: 'IMX_IO_BASE' undeclared (first use in this function)
arch/arm/mach-imx/include/mach/gpio.h:27: error: (Each undeclared identifier is reported only once
arch/arm/mach-imx/include/mach/gpio.h:27: error: for each function it appears in.)
arch/arm/mach-imx/include/mach/gpio.h: In function 'imx_gpio_set_value_inline':
arch/arm/mach-imx/include/mach/gpio.h:36: error: 'IMX_IO_BASE' undeclared (first use in this function)
arch/arm/mach-imx/include/mach/gpio.h:36: error: lvalue required as left operand of assignment
arch/arm/mach-imx/include/mach/gpio.h:38: error: lvalue required as left operand of assignment
...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kernel 2.6.30-rc1 added sys_preadv and sys_pwritev to most archs
but not ARM, resulting in
<stdin>:1421:2: warning: #warning syscall preadv not implemented
<stdin>:1425:2: warning: #warning syscall pwritev not implemented
This patch adds sys_preadv and sys_pwritev to ARM.
These syscalls simply take five long-sized parameters, so they
should have no calling-convention/ABI issues in the kernel.
Tested on armv5tel eabi using a preadv/pwritev test program posted
on linuxppc-dev earlier this month.
It would be nice to get this into the kernel before 2.6.30 final,
so that glibc's kernel version feature test for these syscalls
doesn't have to special-case ARM.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As a result of an off-by-1 error pcm990 leaves one unused GPIO number between
built-in GPIOs and the pca9536 extender. Fix it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Firstly, this patch makes the palm27x asoc driver a little more sane. Also,
since all affected devices use GPIO95 as AC97_nRESET, this patch sets that
properly. Affected are PalmT5, TX and LifeDrive.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Check pending queue and remove the adc client being released.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The symbol 's3c_adc_try' in arch/arm/plat-s3c24xx/adc.c
does not need to be exported and thus should be static.
This fixes the following sparse warning:
adc.c:103:6: warning: symbol 's3c_adc_try' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The .init_machine entry in mach-osiris.c had the same entry
twice, so remove one definition to fix the following warning
from sparse:
mach-osiris.c:416:3: warning: Initializer entry defined twice
mach-osiris.c:418:3: also defined here
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make 'anubis_ide_platdata' statis as it is not used outside
the file it is in, fixing the following sparse warning:
mach-anubis.c:246:27: warning: symbol 'anubis_ide_platdata' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make 'jive_vgg2432a4_display' and 'jive_lcd_config' static as
they are not exported, and are generating the following sparse
warnings:
mach-jive.c:280:26: warning: symbol 'jive_vgg2432a4_display' was not declared. Should it be static?
mach-jive.c:313:28: warning: symbol 'jive_lcd_config' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warning due to s3c_device_hwmon being
missing from <plat/devs.h>
devs.c:380:24: warning: symbol 's3c_device_hwmon' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse error generated by including
<plat/gpio-core.h> instead of <mach/gpio-core.h>
gpiolib.c:78:22: warning: symbol 's3c24xx_gpios' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The VIC code will attempt to perform som
default set_irq_chip() and set_irq_chip_data()
on all IRQs supported by the VIC, while the new
IRQ handling code strictly checks for the global
NR_IRQS to be respected also for these IRQs.
This patch will respect the interrupt mask passed
to the VIC driver and will prevent it from
attempting to call these functions on any unused
interrupts.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes several i.MX board specific defconfig files in favour
for a mx1_defconfig, mx27_defconfig and mx3_defconfig. All config files
have all currently available boards, i.MX specific drivers and the network
device drivers for the boards enabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move ifdef under function brackets. This fixes compile crach when IRQ priorities
are disabled.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
AIPS[12] are no mapped from generic MX3 code so we don't need to
map them from machine-specific map_io function anymore.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Set the correct clkdev-name for the i2c clock.
It also get's rid of the ARCH_NR_GPIOS define on the rationale
that isn't an ARCH-wide setting anyway. If a device has two
pca953x devices, the reserved number will be wrong.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Add an export of the two GPIO configuration calls
s3c_gpio_cfgpin and s3c_gpio_setpull to allow modules
to use them (such as ASoC drivers)
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the filesystem options in the s3c2410_defconfig,
such as building ext4, enable the automounter as modules
and update the network filesysyem choices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
