Two carveout reserved memory nodes each have been added for each of the
C66x DSP remote processor devices present within the MAIN voltage domain
for the TI J721E EVM boards. These nodes are assigned to the respective
rproc device nodes as well. The first region will be used as the DMA pool
for the rproc devices, and the second region will furnish the static
carveout regions for the firmware memory.
The minimum granularity on the Cache settings on C66x DSP cores is 16 MB,
so the DMA memory regions are chosen such that they are in separate 16 MB
regions for each DSP, while reserving a total of 16 MB for each DSP and
not changing the overall DSP remoteproc carveouts.
The current carveout addresses and sizes are defined statically for each
device. The C66x DSP processors do not have an MMU, and as such require the
exact memory used by the firmwares to be set-aside. The firmware images
do not require any RSC_CARVEOUT entries in their resource tables to
allocate the memory for firmware memory segments.
The reserved memory nodes can be disabled later on if there is no use-case
defined to use the corresponding remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-5-s-anna@ti.com
Add the required 'mboxes' property to both the C66x DSP processors for the
TI J721E common processor board. The mailboxes and some shared memory are
required for running the Remote Processor Messaging (RPMsg) stack between
the host processor and each of the DSPs. The nodes are therefore added
in the common k3-j721e-som-p0.dtsi file so that all of these can be
co-located.
The chosen sub-mailboxes match the values used in the current firmware
images. This can be changed, if needed, as per the system integration
needs after making appropriate changes on the firmware side as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-4-s-anna@ti.com
The J721E SoCs have two TMS320C66x DSP Core Subsystems (C66x CorePacs)
in the MAIN voltage domain, each with a C66x Fixed/Floating-Point DSP
Core, and 32 KB of L1P & L1D configurable SRAMs/Cache and an additional
288 KB of L2 configurable SRAM/Cache. These subsystems do not have
an MMU but contain a Region Address Translator (RAT) sub-module for
translating 32-bit processor addresses into larger bus addresses.
The inter-processor communication between the main A72 cores and
these processors is achieved through shared memory and Mailboxes.
Add the DT nodes for these DSP processor sub-systems in the common
k3-j721e-main.dtsi file.
The following firmware names are used by default for these cores, and
can be overridden in a board dts file if desired:
C66x_0 DSP: j7-c66_0-fw
C66x_1 DSP: j7-c66_1-fw
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-3-s-anna@ti.com
The commit eb9f9173d0 ("arm64: dts: ti: k3-j721e-common-proc-board:
Add IPC sub-mailbox nodes") has added the sub-mailbox nodes used by
various remote processors and disabled the unused mailbox clusters
directly in the k3-j721e-common-proc-board dts file. Move all of these
nodes into the k3-j721e-som-p0.dtsi file instead to co-locate all the
mailboxes and the soon to be added DDR reserved-memory carveout nodes
used by remoteprocs within the same dtsi file.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-2-s-anna@ti.com
The various CBASS interconnect nodes on K3 J721E SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200723211137.26641-3-s-anna@ti.com
The various CBASS interconnect nodes on K3 AM65x SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200723211137.26641-2-s-anna@ti.com
Update the ringacc and udma dt nodes to use the latest RM resource types
similar to the ones used in k3-j721e dt nodes.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20200806074826.24607-14-lokeshvutla@ti.com
Update the INTA and INTR dt nodes to the latest DT bindings.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20200806074826.24607-13-lokeshvutla@ti.com
There are three SoC families newly dded to the 32-bit and
64-bit Arm architecture code in the kernel this time:
- Daniel Palmer adds initial support for two chips made by MStar, a
taiwanese SoC manufacturer that became part of Mediatek in 2012. For
now, the added support is fairly minimal, with just two of its
Cortex-A7 based 32-bit camera chips getting support for a limited
set of on-chip peripherals.
- Lars Povlsen from Microchip adds support for their new Sparx5
family of ethernet switch chips using 64-bit Cortex-A53 cores.
These are descended from earlier VSC7xxx SparX and Ocelot chips
using 32-bit MIPS cores.
- Daniele Alessandrelli from Intel adds support for the new Keem Bay
SoC for computer vision, built around a Movidius VPU with Linux
running on Arm Cortex-A53 cores.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Yy3D
-----END PGP SIGNATURE-----
Merge tag 'arm-newsoc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull new ARM SoC support from Arnd Bergmann:
"There are three SoC families newly dded to the 32-bit and 64-bit Arm
architecture code in the kernel this time:
- Daniel Palmer adds initial support for two chips made by MStar, a
taiwanese SoC manufacturer that became part of Mediatek in 2012.
For now, the added support is fairly minimal, with just two of its
Cortex-A7 based 32-bit camera chips getting support for a limited
set of on-chip peripherals.
- Lars Povlsen from Microchip adds support for their new Sparx5
family of ethernet switch chips using 64-bit Cortex-A53 cores.
These are descended from earlier VSC7xxx SparX and Ocelot chips
using 32-bit MIPS cores.
- Daniele Alessandrelli from Intel adds support for the new Keem Bay
SoC for computer vision, built around a Movidius VPU with Linux
running on Arm Cortex-A53 cores"
* tag 'arm-newsoc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: mstar: Correct the compatible string for pmsleep
dt-bindings: arm: mstar: remove the binding description for mstar,pmsleep
dt-bindings: mfd: syscon: add compatible string for mstar,msc313-pmsleep
ARM: mstar: Add reboot support
ARM: mstar: Add "pmsleep" node to base dtsi
ARM: mstar: Add PMU
ARM: mstar: Adjust IMI size for infinity3
ARM: mstar: Adjust IMI size for mercury5
ARM: mstar: Adjust IMI size of infinity
ARM: mstar: Add IMI SRAM region
dt-bindings: arm: mstar: Move existing MStar binding descriptions
dt-bindings: arm: mstar: Add binding details for mstar, pmsleep
ARM: mstar: Fix dts filename for 70mai midrive d08
ARM: mstar: Add dts for 70mai midrive d08
ARM: mstar: Add dts for msc313(e) based BreadBee boards
ARM: mstar: Add mercury5 series dtsis
ARM: mstar: Add infinity/infinity3 family dtsis
ARM: mstar: Add Armv7 base dtsi
ARM: mstar: Add binding details for mstar,l3bridge
ARM: mstar: Add machine for MStar/Sigmastar Armv7 SoCs
...
As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and following
the already supported Cortex-A1`5 and Cortex-A57 based Alpine chips.
This one is added together with the official Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile phone
chips from 2017 based on Cortex-A53 or Kryo 260 CPUs.
A total of five end-user products are added based on these, all
Android phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and
XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals.
It is added along with the HopeRun HiHope RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook
based on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels
and become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board
for the Tegra194, their latest 64-bit chip based on Carmel CPU
cores and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added:
The MYiR MYS-6ULX single-board computer, and four different
models of industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony
Xperia Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards.
Beacon EmbeddedWorks adds another SoM+Carrier development board
for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it
is based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Tpj3
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and
following the already supported Cortex-A1`5 and Cortex-A57 based
Alpine chips. This one is added together with the official
Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile
phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total
of five end-user products are added based on these, all Android
phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals. It is added along with the HopeRun HiHope
RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based
on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels and
become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board for
the Tegra194, their latest 64-bit chip based on Carmel CPU cores
and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added: The
MYiR MYS-6ULX single-board computer, and four different models of
industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia
Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards. Beacon EmbeddedWorks adds another
SoM+Carrier development board for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is
based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)"
* tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits)
arm64: dts: meson: odroid-n2: add jack audio output support
arm64: dts: meson: odroid-n2: enable audio loopback
ARM: dts: berlin: Align L2 cache-controller nodename with dtschema
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
...
For SC7180 this adds the necessary properties for blowing fuses in
qfprom, Coresight fixes, GPU interconnect votes and specifies max speed
for USB controller.
SM8150 and SM8250 gains Adreno SMMU, the graphics management unit and
the GPU nodes, to enable headless GPU usage.
SDM845 gains tracing support for deep idle, GPU bus bandwidth scaling
and DB845c gains the LT9611 HDMI bridge wired up.
MSM8994 gains SMD RPM and SCM support and a new dts for the Sony Xperia
Z5.
MSM8992 is refactored and modernized and gets support for SCM, SPMI,
BLSP2 UART and I2C nodes, PMU, RPM clock controller, PSCI and proper CPU
definitions. Support for the Xiaomi Libra and Microsoft Lumia 950 are
added.
-----BEGIN PGP SIGNATURE-----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=FfiE
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT additional updates for 5.9
For SC7180 this adds the necessary properties for blowing fuses in
qfprom, Coresight fixes, GPU interconnect votes and specifies max speed
for USB controller.
SM8150 and SM8250 gains Adreno SMMU, the graphics management unit and
the GPU nodes, to enable headless GPU usage.
SDM845 gains tracing support for deep idle, GPU bus bandwidth scaling
and DB845c gains the LT9611 HDMI bridge wired up.
MSM8994 gains SMD RPM and SCM support and a new dts for the Sony Xperia
Z5.
MSM8992 is refactored and modernized and gets support for SCM, SPMI,
BLSP2 UART and I2C nodes, PMU, RPM clock controller, PSCI and proper CPU
definitions. Support for the Xiaomi Libra and Microsoft Lumia 950 are
added.
* tag 'qcom-arm64-for-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (31 commits)
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
arm64: dts: qcom: msm8994: Add SCM node
arm64: dts: qcom: sdm845-db845c: Add hdmi bridge nodes
arm64: dts: qcom: add sm8250 GPU nodes
...
Link: https://lore.kernel.org/r/20200730052003.649940-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for audio on jack socket of the odroid-n2
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200701094556.194498-3-jbrunet@baylibre.com
Add capture pcm interfaces and loopback routes to the odroid-n2
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200701094556.194498-2-jbrunet@baylibre.com
These are the latest device tree fixes for Arm SoCs:
- TI Keystone2 ethernet regressed after a driver change broke with
incorrect phy-mode in a board's DT source.
- A similar fix is needed for two i.MX boards that were missed in
an earlier bugfix.
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
- Two fixes for the Allwinner SoCs, one to relax the CMA allocation
ranges that were failing on older SoCs and one to fix Cedrus on the H6.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=qXc9
-----END PGP SIGNATURE-----
Merge tag 'arm-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master
Pull ARM SoC DT fixes from Arnd Bergmann:
"These are the latest device tree fixes for Arm SoCs:
- TI Keystone2 ethernet regressed after a driver change broke with
incorrect phy-mode in a board's DT source.
- A similar fix is needed for two i.MX boards that were missed in an
earlier bugfix.
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
- Two fixes for the Allwinner SoCs, one to relax the CMA allocation
ranges that were failing on older SoCs and one to fix Cedrus on the
H6"
* tag 'arm-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: keystone-k2g-evm: fix rgmii phy-mode for ksz9031 phy
ARM: dts: armada-38x: fix NETA lockup when repeatedly switching speeds
ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detect
ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2
ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2
arm64: dts: allwinner: h6: Fix Cedrus IOMMU usage
ARM: dts sunxi: Relax a bit the CMA pool allocation range
This adds a DPLL clock to the Sparx5 SoC. It is used to generate clock
to misc peripherals, specifically the SDHCI/eMMC controller.
Link: https://lore.kernel.org/r/20200615133242.24911-10-lars.povlsen@microchip.com
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add device tree support for the Microsoft Lumia 950 smartphone.
It is based on msm8992 and supports booting Linux via a custom
EDK2 port.
Currently it supports:
* Screen console via EFIFB
* Booting via EFI_STUB
* SDHCI
* I2C
* PSCI core bringup
Please note that there is an implementation of EL2 startup
on this board, but it requires the user to resign from
PSCI and use spin-table instead. This revision sticks with
PSCI.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200625182118.131476-14-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This commit adds support for the Xiaomi Libra (Mi 4C)
smartphone. It's based on the Qualcomm msm8992 SoC.
It currently supports:
* Screen console from bootloader
* SDHCI
* Regulator configuration
* Serial console
* I2C
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200625182118.131476-13-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This SoC's firmware does not fully support the PSCI
spec, but it's good enough to bring the cores up.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200625182118.131476-11-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for I2C to enable support for peripherals
such as touchscreens or sensors. Also add BLSP_UART2 interface.
Please note that the naming scheme follows downstream and as
abominable as it is, that's what we get.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200625182118.131476-9-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This pinout is common for every 8992-based device and
should therefore reside in the SoC device tree.
Also convert addresses into phandles.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200625182118.131476-5-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the property required for the bootloader to select
the correct device tree blob. It has been removed from
the SoC device tree as it should be set on a per-device
basis.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200625182118.131476-4-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This commit ensures the correct IRQ type is set
and disables the device by default.
The mmc-hs400-1_8v property is also moved to
Bullhead as it might not be present on all boards.
The node has been renamed to sdhci@ instead of mmc@
and the phandle was changed to sdhc_1 to comply with
the newer DTS style.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200625182118.131476-3-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Following changes have been made:
- remove name, compatible and msm-id
- wrap clocks in clocks{}
- order nodes by name and by address
- clock_gcc -> gcc
- msmgpio -> tlmm
- retire msm8992-pins.dtsi
- add some of the missing pins
- make comments C-style
- make apcs a mailbox
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200625182118.131476-2-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add device tree support for the Sony Xperia Z5 smartphone.
It's based on Sony Kitakami platform (msm8994) and hence
a Kitakami-common DTSI has been created so as to reduce
clutter when remaining devices are added.
The board currently supports
* Serial
* SDHCI
* I2C
* Regulator configuration
* pstore log dump
* GPIO keys
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200624150107.76234-9-konradybcio@gmail.com
[bjorn: Changed vendor identifier in board compatible from somc to sony]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This was the only device using that dtsi, so no point
keeping it separate AND with a confusing name (bullhead
is based on msm8992 and the file contains regulator
values for that specific board).
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200624150107.76234-8-konradybcio@gmail.com
[bjorn: Squashed with change that remove regulators from msm8992.dtsi]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add opp-peak-kBps bindings to the GPU opp table, listing the peak
GPU -> DDR bandwidth requirement for each opp level. This will be
used to scale the DDR bandwidth along with the GPU frequency dynamically.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/1594992579-20662-7-git-send-email-akhilpo@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds the interconnects property to the GPU node. This enables
the GPU->DDR path bandwidth voting.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/1594992579-20662-6-git-send-email-akhilpo@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds the interconnects property for the gpu node and the
opp-peak-kBps property to the opps of the gpu opp table. This should
help enable DDR bandwidth scaling dynamically and proportionally to the
GPU frequency.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/1594992579-20662-5-git-send-email-akhilpo@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add "qcom,replicator-loses-context" property to the replicator
in Always-on domain in SC7180 SoC to enable coresight replicator
driver to handle this variation of replicator designs.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/5072d94849cfaee46748d26ac997212fb2d783c2.1591708204.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add "qcom,skip-power-up" property to skip powering up ETM
on SC7180 SoC to workaround a hardware errata where CPU
watchdog counter is stopped when ETM power up bit is set
(i.e., when TRCPDCR.PU = 1).
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/8c5ff297d8c89d9d451352f189baf26c8938842a.1591708204.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Similar to other G12B devices using the W400 dtsi, I see reports of mmc0
tuning errors on VIM3 after a few hours uptime:
[12483.917391] mmc0: tuning execution failed: -5
[30535.551221] mmc0: tuning execution failed: -5
[35359.953671] mmc0: tuning execution failed: -5
[35561.875332] mmc0: tuning execution failed: -5
[61733.348709] mmc0: tuning execution failed: -5
I do not see the same on VIM3L, so remove sd-uhs-sdr50 from the common dtsi
to silence the error, then (re)add it to the VIM3L dts.
Fixes: 4f26cc1c96 ("arm64: dts: khadas-vim3: move common nodes into meson-khadas-vim3.dtsi")
Fixes: 700ab8d839 ("arm64: dts: khadas-vim3: add support for the SM1 based VIM3L")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200721015950.11816-1-christianshewitt@gmail.com
