Placing nftables set support in an extra module is pointless:
1. nf_tables needs dynamic registeration interface for sake of one module
2. nft heavily relies on sets, e.g. even simple rule like
"nft ... tcp dport { 80, 443 }" will not work with _SETS=n.
IOW, either nftables isn't used or both nf_tables and nf_tables_set
modules are needed anyway.
With extra module:
307K net/netfilter/nf_tables.ko
79K net/netfilter/nf_tables_set.ko
text data bss dec filename
146416 3072 545 150033 nf_tables.ko
35496 1817 0 37313 nf_tables_set.ko
This patch:
373K net/netfilter/nf_tables.ko
178563 4049 545 183157 nf_tables.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Like vxlan and erspan opts, geneve opts should also be supported in
nft_tunnel. The difference is geneve RFC (draft-ietf-nvo3-geneve-14)
allows a geneve packet to carry multiple geneve opts. So with this
patch, nftables/libnftnl would do:
# nft add table ip filter
# nft add chain ip filter input { type filter hook input priority 0 \; }
# nft add tunnel filter geneve_02 { type geneve\; id 2\; \
ip saddr 192.168.1.1\; ip daddr 192.168.1.2\; \
sport 9000\; dport 9001\; dscp 1234\; ttl 64\; flags 1\; \
opts \"1:1:34567890,2:2:12121212,3:3:1212121234567890\"\; }
# nft list tunnels table filter
table ip filter {
tunnel geneve_02 {
id 2
ip saddr 192.168.1.1
ip daddr 192.168.1.2
sport 9000
dport 9001
tos 18
ttl 64
flags 1
geneve opts 1:1:34567890,2:2:12121212,3:3:1212121234567890
}
}
v1->v2:
- no changes, just post it separately.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a snapshot of hardidletimer netfilter target.
This patch implements a hardidletimer Xtables target that can be
used to identify when interfaces have been idle for a certain period
of time.
Timers are identified by labels and are created when a rule is set
with a new label. The rules also take a timeout value (in seconds) as
an option. If more than one rule uses the same timer label, the timer
will be restarted whenever any of the rules get a hit.
One entry for each timer is created in sysfs. This attribute contains
the timer remaining for the timer to expire. The attributes are
located under the xt_idletimer class:
/sys/class/xt_idletimer/timers/<label>
When the timer expires, the target module sends a sysfs notification
to the userspace, which can then decide what to do (eg. disconnect to
save power)
Compared to IDLETIMER, HARDIDLETIMER can send notifications when
CPU is in suspend too, to notify the timer expiry.
v1->v2: Moved all functionality into IDLETIMER module to avoid
code duplication per comment from Florian.
Signed-off-by: Manoj Basapathi <manojbm@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The ndp32->wLength is two bytes long, so replace cpu_to_le32 with cpu_to_le16.
Fixes: 0fa81b304a ("cdc_ncm: Implement the 32-bit version of NCM Transfer Block")
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni says:
====================
mptcp: simplify mptcp_accept()
Currently we allocate the MPTCP master socket at accept time.
The above makes mptcp_accept() quite complex, and requires checks is several
places for NULL MPTCP master socket.
These series simplify the MPTCP accept implementation, moving the master socket
allocation at syn-ack time, so that we drop unneeded checks with the follow-up
patch.
v1 -> v2:
- rebased on top of 2398e3991b
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch subflow->conn is always != NULL and
is never changed. We can drop a bunch of now unneeded checks.
v1 -> v2:
- rebased on top of commit 2398e3991b ("mptcp: always
include dack if possible.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change moves the mptcp socket allocation from mptcp_accept() to
subflow_syn_recv_sock(), so that subflow->conn is now always set
for the non fallback scenario.
It allows cleaning up a bit mptcp_accept() reducing the additional
locking and will allow fourther cleanup in the next patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify code, which
contains platform_get_resource and devm_ioremap_resource.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Being a non-physical port, the CPU port does not have an ocelot_port
structure, so the ocelot_port_writel call inside the
ocelot_port_set_maxlen() function would access data behind a NULL
pointer.
This is a patch for net-next only, the net tree boots fine, the bug was
introduced during the net -> net-next merge.
Fixes: 1d34357931 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Fixes: a8015ded89 ("net: mscc: ocelot: properly account for VLAN header length when setting MRU")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling:
tipc_node_link_down()->
- tipc_node_write_unlock()->tipc_mon_peer_down()
- tipc_mon_peer_down()
just after disabling bearer could be caused kernel oops.
Fix this by adding a sanity check to make sure valid memory
access.
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking and returning 'true' boolean is useless as it will be
returning at end of function
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected almost all
unsupported parameters (missing sample_rate_interval).
As a side effect of these changes the error code for
unsupported params changes from EINVAL to EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
As a side effect of these changes the error code for
unsupported params changes from EINVAL to EOPNOTSUPP.
The driver was missing a check for rate_sample_interval.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver correctly rejects all unsupported
parameters, no functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver correctly rejects all unsupported
parameters, no functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: phy: split the mscc driver
This is a proposal to split the MSCC PHY driver, as its code base grew a
lot lately (it's already 3800+ lines). It also supports features
requiring a lot of code (MACsec), which would gain in being split from
the driver core, for readability and maintenance. This is also done as
other features should be coming later, which will also need lots of code
addition.
This series shouldn't change the way the driver works.
I checked, and there were no patch pending on this driver. This change
was done on top of all the modifications done on this driver in net-next.
Since v2:
- Defined inline functions as static inline.
- Fixed a locking issue reported by Kbuild.
Since v1:
- Moved more definitions into the mscc_macsec.h header.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic commit fixing the MSCC PHY header defines and descriptions,
which were referring the to MSCC Ocelot MAC driver (see
drivers/net/ethernet/mscc/).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the MSCC driver into separate files, per
functionality, to improve readability and maintenance as the codebase
grew a lot. The MACsec code is moved to a dedicated mscc_macsec.c file,
the mscc.c file is renamed to mscc_main.c to keep the driver binary to
be named mscc and common definition are put into a new mscc.h header.
Most of the code was just moved around, except for a few exceptions:
- Header inclusions were reworked to only keep what's needed.
- Three helpers were created in the MACsec code, to avoid #ifdef's in
the main C file: vsc8584_macsec_init, vsc8584_handle_macsec_interrupt
and vsc8584_config_macsec_intr.
The patch should not introduce any functional modification.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC PHY driver is growing, with lots of space consuming features
(firmware support, full initialization, MACsec...). It's becoming hard
to read and navigate in its source code. This patch moves the MSCC
driver to its own directory, without modifying anything, as a
preparation for splitting up its features into dedicated files.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
RED: Introduce an ECN tail-dropping mode
When the RED qdisc is currently configured to enable ECN, the RED algorithm
is used to decide whether a certain SKB should be marked. If that SKB is
not ECN-capable, it is early-dropped.
It is also possible to keep all traffic in the queue, and just mark the
ECN-capable subset of it, as appropriate under the RED algorithm. Some
switches support this mode, and some installations make use of it.
There is currently no way to put the RED qdiscs to this mode.
Therefore this patchset adds a new RED flag, TC_RED_TAILDROP. When the
qdisc is configured with this flag, non-ECT traffic is enqueued (and
tail-dropped when the queue size is exhausted) instead of being
early-dropped.
Unfortunately, adding a new RED flag is not as simple as it sounds. RED
flags are passed in tc_red_qopt.flags. However RED neglects to validate the
flag field, and just copies it over wholesale to its internal structure,
and later dumps it back.
A broken userspace can therefore configure a RED qdisc with arbitrary
unsupported flags, and later expect to see the flags on qdisc dump. The
current ABI thus allows storage of 5 bits of custom data along with the
qdisc instance.
GRED, SFQ and CHOKE qdiscs are in the same situation. (GRED validates VQ
flags, but not the flags for the main queue.) E.g. if SFQ ever needs to
support TC_RED_ADAPTATIVE, it needs another way of doing it, and at the
same time it needs to retain the possibility to store 6 bits of
uninterpreted data.
For RED, this problem is resolved in patch #2, which adds a new attribute,
and a way to separate flags from userbits that can be reused by other
qdiscs. The flag itself and related behavioral changes are added in patch
To test the new feature, patch #1 first introduces a TDC testsuite that
covers the existing RED flags. Patch #5 later extends it with taildrop
coverage. Patch #6 contains a forwarding selftest for the offloaded
datapath.
To test the SW datapath, I took the mlxsw selftest and adapted it in mostly
obvious ways. The test is stable enough to verify that RED, ECN and ECN
taildrop actually work. However, I have no confidence in its portability to
other people's machines or mildly different configurations. I therefore do
not find it suitable for upstreaming.
GRED and CHOKE can use the same method as RED if they ever need to support
extra flags. SFQ uses the length of TCA_OPTIONS to dispatch on binary
control structure version, and would therefore need a different approach.
v2:
- Patch #1
- Require nsPlugin in each RED test
- Match end-of-line to catch cases of more flags reported than
requested
- Patch #2:
- Replaced with another patch.
- Patch #3:
- Fix red_use_taildrop() condition in red_enqueue switch for
probabilistic case.
- Patch #5:
- Require nsPlugin in each RED test
- Match end-of-line to catch cases of more flags reported than
requested
- Add a test for creation of non-ECN taildrop, which should fail
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend RED testsuite to cover the new nodrop mode of RED-ECN. This test is
really similar to ECN test, diverging only in the last step, where UDP
traffic should go to backlog instead of being dropped. Thus extract a
common helper, ecn_test_common(), make do_ecn_test() into a relatively
simple wrapper, and add another one, do_ecn_nodrop_test().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RED ECN nodrop mode means that non-ECT traffic should not be early-dropped,
but enqueued normally instead. In Spectrum systems, this is achieved by
disabling CWTPM.ew (enable WRED) for a given traffic class.
So far CWTPM.ew was unconditionally enabled. Instead disable it when the
RED qdisc is in nodrop mode.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the RED Qdisc is currently configured to enable ECN, the RED algorithm
is used to decide whether a certain SKB should be marked. If that SKB is
not ECN-capable, it is early-dropped.
It is also possible to keep all traffic in the queue, and just mark the
ECN-capable subset of it, as appropriate under the RED algorithm. Some
switches support this mode, and some installations make use of it.
To that end, add a new RED flag, TC_RED_NODROP. When the Qdisc is
configured with this flag, non-ECT traffic is enqueued instead of being
early-dropped.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qdiscs RED, GRED, SFQ and CHOKE use different subsets of the same pool
of global RED flags. These are passed in tc_red_qopt.flags. However none of
these qdiscs validate the flag field, and just copy it over wholesale to
internal structures, and later dump it back. (An exception is GRED, which
does validate for VQs -- however not for the main setup.)
A broken userspace can therefore configure a qdisc with arbitrary
unsupported flags, and later expect to see the flags on qdisc dump. The
current ABI therefore allows storage of several bits of custom data to
qdisc instances of the types mentioned above. How many bits, depends on
which flags are meaningful for the qdisc in question. E.g. SFQ recognizes
flags ECN and HARDDROP, and the rest is not interpreted.
If SFQ ever needs to support ADAPTATIVE, it needs another way of doing it,
and at the same time it needs to retain the possibility to store 6 bits of
uninterpreted data. Likewise RED, which adds a new flag later in this
patchset.
To that end, this patch adds a new function, red_get_flags(), to split the
passed flags of RED-like qdiscs to flags and user bits, and
red_validate_flags() to validate the resulting configuration. It further
adds a new attribute, TCA_RED_FLAGS, to pass arbitrary flags.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a handful of tests for creating RED with different flags.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corresponds to the MAC_SPOOFING_TX privilege in the hardware.
Some firmware versions on some cards don't support the feature, so check
the TX_MAC_SECURITY capability and fail EOPNOTSUPP if trying to enable
spoofchk on a NIC that doesn't support it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: phy: XLGMII define and usage in PHYLINK
Adds XLGMII defines and usage in PHYLINK.
Patch 1/2, adds the define for it, whilst 2/2 adds the usage of it in
PHYLINK.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add XLGMII interface and the list of XLGMII speeds to PHYLINK.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a statement that is indented incorrectly, remove a space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switches supported so far by the driver only have non-SerDes ports,
so they should be configured in the PHYLINK callback that provides the
resolved PHY link parameters.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more T5/T6 registers to be collected in register dump:
1. MPS register range 0x9810 to 0x9864 and 0xd000 to 0xd004.
2. NCSI register range 0x1a114 to 0x1a130 and 0x1a138 to 0x1a1c4.
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Misc update to mlx5 core and E-Switch driver:
1) Blue-Field, Update VF vports config when num of VFs changed
From Bodon, Various misc cleanups and refactoring
for vport enabling/disabling routines to allow them to be called
dynamically and not only on E-Switch load.
This will allow ECPF (ConnectX BlueField Smartnic) support for dynamic
num vf changes and dynamic vport creation and configuration as introduced
in "Update VF vports config when num of VFs changed" patch.
2) From Parav and Mark, trivial clean-ups.
3) Software steering support for flow table id as destination
and a clean-up patch to remove unnecessary function stubs, from Alex.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl5sFqcACgkQSD+KveBX
+j6KxAf+INpm/mpG4+Vk7loUw0C3xnchOMwIZhKuanWiqsbO+tWC8g1AYgpFRKdE
gkE18EN0verQEqnol7N7+HhnHboqvmqT1/FOvOF9pRVpQWDEoE73oJzT6vF42u5M
Hg/Rsh0Q+R6pjDr62/MOJrysCFip87GG6TDerWhQ3Fol6ZL8vHMaQkTdyxcVTIAP
TidHQWs4Cc82tpfsIirBKIylcbBxbgj4kQE4Ov81hm6FE3h4ZV3rJ+dXp4WCj9TL
PbSgtnZ1kc+GOryF8AfRU197bIrXFHfraog7Qi6hVspf8QK+w4Iz9wy3Z2SCAxVA
dCc/DC29o0dOcUn72Xrqc2+6M2Jnyw==
=ui+6
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-03-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-03-13
Misc update to mlx5 core and E-Switch driver:
1) Blue-Field, Update VF vports config when num of VFs changed
From Bodon, Various misc cleanups and refactoring
for vport enabling/disabling routines to allow them to be called
dynamically and not only on E-Switch load.
This will allow ECPF (ConnectX BlueField Smartnic) support for dynamic
num vf changes and dynamic vport creation and configuration as introduced
in "Update VF vports config when num of VFs changed" patch.
2) From Parav and Mark, trivial clean-ups.
3) Software steering support for flow table id as destination
and a clean-up patch to remove unnecessary function stubs, from Alex.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-03-13
The following pull-request contains BPF updates for your *net-next* tree.
We've added 86 non-merge commits during the last 12 day(s) which contain
a total of 107 files changed, 5771 insertions(+), 1700 deletions(-).
The main changes are:
1) Add modify_return attach type which allows to attach to a function via
BPF trampoline and is run after the fentry and before the fexit programs
and can pass a return code to the original caller, from KP Singh.
2) Generalize BPF's kallsyms handling and add BPF trampoline and dispatcher
objects to be visible in /proc/kallsyms so they can be annotated in
stack traces, from Jiri Olsa.
3) Extend BPF sockmap to allow for UDP next to existing TCP support in order
in order to enable this for BPF based socket dispatch, from Lorenz Bauer.
4) Introduce a new bpftool 'prog profile' command which attaches to existing
BPF programs via fentry and fexit hooks and reads out hardware counters
during that period, from Song Liu. Example usage:
bpftool prog profile id 337 duration 3 cycles instructions llc_misses
4228 run_cnt
3403698 cycles (84.08%)
3525294 instructions # 1.04 insn per cycle (84.05%)
13 llc_misses # 3.69 LLC misses per million isns (83.50%)
5) Batch of improvements to libbpf, bpftool and BPF selftests. Also addition
of a new bpf_link abstraction to keep in particular BPF tracing programs
attached even when the applicaion owning them exits, from Andrii Nakryiko.
6) New bpf_get_current_pid_tgid() helper for tracing to perform PID filtering
and which returns the PID as seen by the init namespace, from Carlos Neira.
7) Refactor of RISC-V JIT code to move out common pieces and addition of a
new RV32G BPF JIT compiler, from Luke Nelson.
8) Add gso_size context member to __sk_buff in order to be able to know whether
a given skb is GSO or not, from Willem de Bruijn.
9) Add a new bpf_xdp_output() helper which reuses XDP's existing perf RB output
implementation but can be called from tracepoint programs, from Eelco Chaudron.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove dummy functions declaration, the dummy functions are not needed
since fs_dr is the only one to call mlx5dr and both fs_dr and dr files
depend on the same config flag (MLX5_SW_STEERING).
Fixes: 70605ea545 ("net/mlx5: DR, Expose APIs for direct rule managing")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This action allows to go to a flow table based on the table id.
Goto flow table id is required for supporting user space SW.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
