At module unload, omap_fbdev_free() gets called which releases the
framebuffers. However, the framebuffers are still used by crtcs, and
will be released only later at vsync. The driver doesn't wait for this,
and goes on to release the rest of the resources, which often
causes a crash.
This patchs adds a omap_crtc_flush() function which waits until the crtc
has finished with its apply queue and page flips.
The function utilizes a simple polling while-loop, as the performance is
not an issue here.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=/Uwk
-----END PGP SIGNATURE-----
Merge tag 'omapdrm-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
omapdrm patches for 3.14
* tag 'omapdrm-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
drm/omap: Enable DT support for DMM
drm/omap: fix: change dev_unload order
drm/omap: fix: disable encoder before destroying it
drm/omap: fix: disconnect devices when omapdrm module is removed
drm/omap: fix: Defer probe if an omapdss device requests for it at connect
drm/omap: fix (un)registering irqs inside an irq handler
Conflicts:
drivers/gpu/drm/omapdrm/omap_drv.c
With the omapdss device model changes. omapdrm is required to call dssdriver's
connect() op to register a panel. This is currently done in omap_modeset_init()
A call to connect() can fail if the omapdss panels or the encoders(HDMI/DPI)
they connect to have some resource(like regulators, I2C adapter) missing. If
this happens, the correct approach is to defer omapdrm's probe.
omapdrm currently ignores those panels which return a non zero value when
connected. This could result in omapdrm ignoring all panels on an omap board.
The right approach would be for omapdrm to request for probe deferral when a
panel's connect op returns -EPROBE_DEFER.
In order to do this, we need to call connect() much earlier during omapdrm's
probe to prevent too many things are already done by then. We now connect the
panels during pdev_probe(), before anything else is initialized, so that we
don't need to undo too many things if a defer was requested.
Now when we enter omap_modeset_init(), we have a set of panels that have been
connected. We now proceed with registering only those panels that are already
connected.
A special case has to be considered when no panels are available to connect when
omapdrm probes. In this case too, we defer probe and expect that a panel will be
available to connect the next time.
Checking whether the panel has a driver or whether it has get_timing/read_edid
ops in omap_modeset_init() are redundant with the new display model. These can
be removed since a dssdev device will always have a driver associated with it,
and all dssdev drivers have a get_timings op.
This will mainly fix cases when omapdrm is built-in the kernel, since that's
generally where resources like regulators or I2C are unavailable because of
probe order dependencies.
In particular this fixes boot with omapdrm built-in on an omap4 panda ES board.
The regulators used by HDMI(provided by I2C based TWL regulators) aren't
initialized because I2C isn't initialized, I2C isn't initialized as it's pins
are not configured because pinctrl is yet to probe.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm (un)registers irqs inside an irq handler. The problem is that
the (un)register function uses dispc_runtime_get/put() to enable the
clocks, and those functions are not irq safe by default.
This was kind of fixed in 48664b21ae
(OMAPDSS: DISPC: set irq_safe for runtime PM), which makes dispc's
runtime calls irq-safe.
However, using pm_runtime_irq_safe in dispc makes the parent of dispc,
dss, always enabled, effectively preventing PM for the whole DSS module.
This patch makes omapdrm behave better by adding new irq (un)register
functions that do not use dispc_runtime_get/put, and using those
functions in interrupt context. Thus we can make dispc again
non-irq-safe, allowing proper PM.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
I've killed them a long time ago in drm/i915, let's get rid of this
remnant of shared drm core days for good.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers embed gem-objects into their own buffer objects. There is no
reason to keep drm_gem_object_alloc(), gem->driver_private and
->gem_init_object() anymore.
New drivers are highly encouraged to do the same. There is no benefit in
allocating gem-objects separately.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
And simplify how we hold a ref+pin to what is being scanned out by using
fb refcnt'ing. The previous logic pre-dated fb refcnt, and as a result
was less straightforward than it could have been. By holding a ref to
the fb, we don't have to care about how many plane's there are and
holding a ref to each color plane's bo.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All the gem based kms drivers really want the same function to
destroy a dumb framebuffer backing storage object.
So give it to them and roll it out in all drivers.
This still leaves the option open for kms drivers which don't use GEM
for backing storage, but it does decently simplify matters for gem
drivers.
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Cc: Ben Skeggs <skeggsb@gmail.com>
Reviwed-by: Rob Clark <robdclark@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently omapdrm creates crtcs, which map directly to DSS overlay
managers, only on demand at init time. This would make it difficult to
manage connecting the display entities in the future, as the code cannot
just search for a suitable overlay manager.
We cannot fix this the sane way, which would be to create crtcs for each
overlay manager, because we need an overlay for each crtc. With limited
number of overlays, that's not possible.
So the solution for now is to detach the overlay manager from the crtc.
crtcs are still created on demand at init time, but all overlay managers
are always initialized by the omapdss.
This way we can create and connect whole display pipelines from the
overlay manager to the display, regardless of which crtcs omapdrm would
create.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm driver currently takes a config/module arg to figure out the number
of crtcs it needs to create. We could create as many crtcs as there are overlay
managers in the DSS hardware, but we don't do that because each crtc eats up
one DSS overlay, and that reduces the number of planes we can attach to a single
crtc.
Since the number of crtcs may be lesser than the number of hardware overlay
managers, we need to figure out which overlay managers to use for our crtcs. The
current approach is to use pipe2chan(), which returns a higher numbered manager
for the crtc.
The problem with this approach is that it assumes that the overlay managers we
choose will connect to the encoders the platform's panels are going to use,
this isn't true, an overlay manager connects only to a few outputs/encoders, and
choosing any overlay manager for our crtc might lead to a situation where the
encoder cannot connect to any of the crtcs we have chosen. For example, an
omap5-panda board has just one hdmi output. If num_crtc is set to 1, with the
current approach, pipe2chan will pick up the LCD2 overlay manager, which cannot
connect to the hdmi encoder at all. The only manager that could have connected
to hdmi was the TV overlay manager.
Therefore, there is a need to choose our overlay managers keeping in mind the
panels we have on that platform. The new approach iterates through all the
available panels, creates encoders and connectors for them, and then tries to
get a suitable overlay manager to create a crtc which can connect to the
encoders.
We use the dispc_channel field in omap_dss_output to retrieve the desired
overlay manager's channel number, we then check whether the manager had already
been assigned to a crtc or not. If it was already assigned to a crtc, we assume
that out of all the encoders which intend use this crtc, only one will run at a
time. If the overlay manager wan't assigned to a crtc till then, we create a
new crtc and link it with the overlay manager.
This approach just looks for the best dispc_channel for each encoder. On DSS HW,
some encoders can connect to multiple overlay managers. Since we don't try
looking for alternate overlay managers, there is a greater possibility that 2
or more encoders end up asking for the same crtc, causing only one encoder to
run at a time.
Also, this approach isn't the most optimal one, it can do either good or bad
depending on the sequence in which the panels/outputs are parsed. The optimal
way would be some sort of back tracking approach, where we improve the set of
managers we use as we iterate through the list of panels/encoders. That's
something left for later.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the omapdss interface has been reworked so that omapdrm can use
dispc directly, we have been able to fix the remaining functional kms
issues with omapdrm. And in the mean time the PM sequencing and many
other of that open issues have been solved. So I think it makes sense
to finally move omapdrm out of staging.
Signed-off-by: Rob Clark <robdclark@gmail.com>
