The code ignored the I2C_M_RD flag on I2C messages. Instead it assumed
an i2c transaction with a single message must be a write operation and a
transaction with two messages would be a read operation.
Though this works for the driver code, it leads to problems once the i2c
device is exposed to code not knowing this convention. For example,
I did "insmod i2c-dev" and issued read requests from userspace, which
were translated into write requests and destroyed the EEPROM of my
device.
So, just check and respect the I2C_M_READ flag, which indicates a read
when set on a message. If it is absent, it is a write message.
Incidentally, changing from the case statement to a while loop allows
the code to lift the limitation to two i2c messages per transaction.
There are 4 more *_i2c_transfer functions affected by the same behaviour
and limitation that should be fixed in the same way.
Link: https://lore.kernel.org/linux-media/20220116112238.74171-2-micha@freedict.org
Signed-off-by: Michael Bunk <micha@freedict.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The new m88ds3101b demodulator version requires the highest bit of
register 0x11 be cleared after tuning to a new frequency to make the
lock output pin go high when a signal is found. This pin is normally
connected to an indicator led.
Link: https://lore.kernel.org/linux-media/20220116112238.74171-1-micha@freedict.org
Signed-off-by: Michael Bunk <micha@freedict.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It is possible that mtk_vcodec_enc_pw_on fails, and in that scenario
the PM counter is not incremented, and subsequent call to
mtk_vcodec_enc_pw_off decrements the counter, leading to a PM imbalance.
Fix by bailing out of venc_if_encode in the case when mtk_vcodec_enc_pw_on
fails.
Fixes: 4e855a6efa ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Encoder Driver")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In the MediaTek vcodec driver, while mtk_vcodec_mem_free() is mostly
called only when the buffer to free exists, there are some instances
that didn't do the check and triggered warnings in practice.
We believe those checks were forgotten unintentionally. Add the checks
back to fix the warnings.
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In mtk_vcodec_mem_free(), there are two cases where a NULL VA is passed:
- mem->size == 0: we are called to free no memory. This may happen when
we call mtk_vcodec_mem_free() twice or the memory has never been
allocated.
- mem->size > 0: we are called to free memory but without VA. This means
that we failed to free the memory for real.
Both cases are not expected to happen, and we want to have clearer error
messages to describe which one we just encountered.
Update the error messages to include more information for that purpose.
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In mtk_vcodec_mem_alloc() and mtk_vcodec_mem_free(), the value of
mem->size is not expected to change before and when using the DMA APIs
and debug print, so there's no point in keeping local copies of it.
Drop the local variable "size" in the mentioned functions, and update
printk format identifiers accordingly.
This makes the code slightly more visually consistent, and retrieve a
small amount of memory that is used for no real purpose.
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
mtk_v4l2_err() already uses dev_err(), so don't print the device name
again. Print the function name instead.
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Set the owner field of the async sub-devices by making
v4l2_async_register_subdev() a macro and obtaining THIS_MODULE that way.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Set a sub-device's owner field to the caller's module, provided as an
argument to the function. v4l2_device_register_subdev() becomes a macro
passing THIS_MODULE to the __v4l2_device_register_subdev() function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Drop dev_err() and use the dev_err_probe() helper on probe path.
No functional changes intended.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Set timing-related and BLC anchor registers via cci calls instead of
hardcoding them in the register table. This prepares the driver for
implementation of configurable analogue crop and binning. No
functional change intended.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Pixel array dimensions and default crop size do not belong to the
ov4689_mode structure, since they are mode independent. Make them
defines instead.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OV4689 sensor has separate red and blue gain settings (up to 4x).
Implement appropriate controls in the driver. Default gain values
are not modified.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OV4689 sensor supports digital gain up to 16x. Implement
corresponding control in the driver. Default digital gain value is not
modified by this patch.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OV4689 sensor supports horizontal and vertical flipping. Add
appropriate controls to the driver. Toggling both array flip and
digital flip bits allows to achieve flipping while maintaining output
Bayer order. Note that the default value of hflip control corresponds
to both bits set, as it was before this patch.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make horizontal blanking configurable. To do so, set HTS register
according to the requested horizontal blanking in ov4689_set_ctrl
instead of the register table. Default HTS value is not changed by
this patch. Minimal HTS value is found experimentally and corresponds
to 90 fps framerate at minimum vertical blanking. Real HTS value is
the register value multiplied by 4.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
max_fps field of struct ov4689_mode is unused in this driver, so
remove it.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use runtime PM autosuspend to avoid powering off the sensor during
fast stop-reconfigure-restart cycles.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As the sensor may be accessible right after its async sub-device is
registered, enable runtime PM before doing so.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use sub-device active state. Employ control handler lock to
synchronize access to the active state and s_stream.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Introduce local variable for regmap within the ov4689_set_ctrl
function. This adjustment eliminates repetition within the function.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The 'client' field within the 'ov4689' structure is solely used to
access its 'dev' member. This commit removes the 'client' field and
directly stores a pointer to the 'struct device'.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the i2c register accesses to utilize the CCI helper library
rather than relying on driver-specific functions. Also, set analogue
gain in a single 16-bit write instead of two 8-bit writes.
[Sakari Ailus: Initialise sensor_gain as 0.]
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Put register defininitions in the order of increasing register
address.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Many values in the register table are actually power-on
defaults. Remove those and also unused HDR exposures and gains.
Annotate the remaining values using the publicly available datasheet
to facilitate further development. No functional change intended.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The subtract in this condition is reversed. The ->length is the length
of the buffer. The ->bytesused is how many bytes we have copied thus
far. When the condition is reversed that means the result of the
subtraction is always negative but since it's unsigned then the result
is a very high positive value. That means the overflow check is never
true.
Additionally, the ->bytesused doesn't actually work for this purpose
because we're not writing to "buf->mem + buf->bytesused". Instead, the
math to calculate the destination where we are writing is a bit
involved. You calculate the number of full lines already written,
multiply by two, skip a line if necessary so that we start on an odd
numbered line, and add the offset into the line.
To fix this buffer overflow, just take the actual destination where we
are writing, if the offset is already out of bounds print an error and
return. Otherwise, write up to buf->length bytes.
Fixes: 9cb2173e6e ("[media] media: Add stk1160 new driver (easycap replacement)")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Ensure that drivers set max_num_buffers to a value >= 32.
For now there is no reason for drivers to request a lower
limit and doing so might potentially cause userspace issues.
Note that the old check of > MAX_BUFFER_INDEX was pointless
since q->max_num_buffers was already limited to MAX_BUFFER_INDEX
or less.
Also add a sanity check in __vb2_init_fileio(), returning
-ENOSPC if a driver returns more than 32 buffers from
VIDIOC_REQBUFS with count = q->min_reqbufs_allocation.
The vb2_fileio_data struct only supports up to 32 buffers,
so we need a check there.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
If the CEC device is unregistered, then an attempt to open
the device node should result in an -ENODEV error instead of
-ENXIO.
Document this as well in cec-func-open.rst.
This is consistent with the error code returned by other
file operations such as ioctl.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
After the new V4L2 device node was registered, some additional
initialization was done before the device node was marked as
'registered'. During the time between creating the device node
and marking it as 'registered' it was possible to open the
device node, which would return -ENODEV since the 'registered'
flag was not yet set.
Hold the videodev_lock mutex from just before the device node
is registered until the 'registered' flag is set. Since v4l2_open
will take the same lock, it will wait until this registration
process is finished. This resolves this race condition.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: <stable@vger.kernel.org> # for vi4.18 and up
-----BEGIN PGP SIGNATURE-----
iJgEABYKAEAWIQTAnvhxs4J7QT+XHKnMPy2AAyfeZAUCZiJiwyIcbGF1cmVudC5w
aW5jaGFydEBpZGVhc29uYm9hcmQuY29tAAoJEMw/LYADJ95kLugBAOcLTOwWAJn7
D4YFSSN/ak9ycnNeD+ixIgjTAttrJrTYAP4s3hitW4k0P6rhGbAjYGlOvKNk4fbx
M4MxokoXVd0gDw==
=fWyC
-----END PGP SIGNATURE-----
Merge tag 'tags/media-next-uvc-20240419' of git://git.kernel.org/pub/scm/linux/kernel/git/pinchartl/linux.git into media_stage
uvcvideo fixes:
Ricardo Ribalda (3):
media: uvcvideo: Add quirk for Logitech Rally Bar
media: uvcvideo: Fix power line control for Shine-Optics Camera
media: uvcvideo: Disable autosuspend for Insta360 Link
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.linuxtv.org/project/linux-media/patch/20240419125149.GA2125@pendragon.ideasonboard.com/
Add description for 'struct regmap *cci' member of struct imx335.
This will fix the following compile-time warning:
warning: Function parameter or struct member 'cci' not described in 'imx335'
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
On some ACPI platforms, such as Chromebooks the ACPI methods to
change the power-state (_PS0 and _PS3) fully take care of powering
on/off the sensor.
On other ACPI platforms, such as e.g. various HP models with IPU6 +
hi556 sensor, the sensor driver must control the avdd regulator itself.
Add support for having the driver control the sensor's avdd regulator.
Note this relies on the regulator-core providing a dummy regulator
(which it does by default) on platforms where Linux is not aware of
the avdd regulator.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
On some ACPI platforms, such as Chromebooks the ACPI methods to
change the power-state (_PS0 and _PS3) fully take care of powering
on/off the sensor.
On other ACPI platforms, such as e.g. various HP models with IPU6 +
hi556 sensor, the sensor driver must control the sensor's clock itself.
Add support for having the driver control an optional clock.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
On some ACPI platforms, such as Chromebooks the ACPI methods to
change the power-state (_PS0 and _PS3) fully take care of powering
on/off the sensor.
On other ACPI platforms, such as e.g. various HP models with IPU6 +
hi556 sensor, the sensor driver must control the reset GPIO itself.
Add support for having the driver control an optional reset GPIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With ipu bridge, endpoints may only be created when ipu bridge has
initialised. This may happen after the sensor driver has first probed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add camera orientation and sensor rotation controls using
the v4l2_fwnode_device_parse() and v4l2_ctrl_new_fwnode_properties()
helpers.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add hblank control so that the sensor has all the mandatory
controls for libcamera.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add vblank control to allow changing the framerate /
higher exposure values.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The hts, vts ov2680_mode struct members always contain
OV2680_PIXELS_PER_LINE resp. OV2680_LINES_PER_FRAME,
drop them and simply use these values directly.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is no reason to send OV2680_END_MARGIN extra columns on top of
the mode width and the same for sending extra lines over the mode height.
This sending of extra lines/columns was inherited from the atomisp
ov2680 driver, it is unclear why this was done and this complicates
adding V4L2_CID_VBLANK support, so remove it.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Since commit 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint
property verification") the ov2680 driver no longer probes when the
'data-lanes' property is absent.
The OV2680 sensor has only one data lane, so there is no need for
describing it the devicetree.
Remove the unnecessary data-lanes property check.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Fixes: 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint property verification")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The sensor gain (both analog and digital) are controlled by a
single gain value where:
- 0dB to 30dB correspond to analog gain
- 30.3dB to 72dB correspond to digital gain
(with 0.3dB step)
Hence, limit the analogue gain value to 100.
For digital gain, support can be added later if needed.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The imx335 reports a recommended pixel area of - 2592x1944.
The driver supported mode however limits it to height=1940.
Fix the height discrepency by correctly the value of height
(with updates to vblank and mode registers).
The IMX335_REG_HTRIMMING should also be corrected to the start
offset(i.e. 48) instead of chosing a abritrary crop start of 384.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Consider integer values for registers that are related to various
sizes in the register map. This helps in improving the overall
readability.
No functional changes intended in this patch.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the new comon CCI register access helpers to replace the private
register access helpers in the imx335 driver.
Select V4L2_CCI_I2C Kconfig option which the imx335 driver now
depends on.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Call the V4L2 fwnode device parser to handle controls that are
standardised by the framework.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The IMX335 can support both 2 and 4 lane configurations.
Extend the driver to configure the lane mode accordingly.
Update the pixel rate depending on the number of lanes in use.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: fixup missing : in @lane_mode kerneldoc line]
If the control handler is in an error state, return that error immediately
in v4l2_ctrl_new_fwnode_properties(). Effectively the change here is that
the same error code (handler's error) is returned in all cases instead of
possibly returning -EINVAL.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Turn on the privacy LED only if streamon succeeds. This can be done after
enabling streaming on the sensor.
Fixes: b6e10ff6c2 ("media: v4l2-core: Make the v4l2-core code enable/disable the privacy LED if present")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
After the frame is submitted to DMA, it may happen that the submitted
list is not updated soon enough, and the DMA callback is triggered
before that.
This can lead to kernel crashes, so move everything in a single
lock/unlock section to prevent such races.
Fixes: b4a3d877dc ("media: ti: Add CSI2RX support for J721E")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When the source device is operating above 1.5 Gbps per lane, it needs to
send the Skew Calibration Sequence before sending any HS data. If the
DPHY is initialized after the source stream is started, then it might
miss the sequence and not be able to receive data properly. Move the
start of source subdev to the end of the sequence to make sure
everything is ready to receive data before the source starts streaming.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Fixes: 3295cf1241 ("media: cadence: Add support for external dphy")
Tested-by: Julien Massot <julien.massot@collabora.com>
Tested-by: Changhuang Liang <Changhuang.liang@starfivetech.com>
Reviewed-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Changhuang Liang <Changhuang.liang@starfivetech.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
First the media device node was created, and if successful it was
marked as 'registered'. This leaves a small race condition where
an application can open the device node and get an error back
because the 'registered' flag was not yet set.
Change the order: first set the 'registered' flag, then actually
register the media device node. If that fails, then clear the flag.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fixes: cf4b9211b5 ("[media] media: Media device node support")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
When the device suspends, it keeps power-cycling.
The user notices it because the LED constanct oscillate between
blue (ready) and no LED (off).
<6>[95202.128542] usb 3-3-port4: attempt power cycle
<6>[95206.070120] usb 3-3.4: new high-speed USB device number 49 using xhci_hcd
<6>[95206.212027] usb 3-3.4: New USB device found, idVendor=2e1a, idProduct=4c01, bcdDevice= 2.00
<6>[95206.212044] usb 3-3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=<Serial: 1>
<6>[95206.212050] usb 3-3.4: Product: Insta360 Link
<6>[95206.212075] usb 3-3.4: Manufacturer: Amba
<7>[95206.214862] usb 3-3.4: GPIO lookup for consumer privacy
<7>[95206.214866] usb 3-3.4: using lookup tables for GPIO lookup
<7>[95206.214869] usb 3-3.4: No GPIO consumer privacy found
<6>[95206.214871] usb 3-3.4: Found UVC 1.10 device Insta360 Link (2e1a:4c01)
<3>[95206.217113] usb 3-3.4: Failed to query (GET_INFO) UVC control 14 on unit 1: -32 (exp. 1).
<3>[95206.217733] usb 3-3.4: Failed to query (GET_INFO) UVC control 16 on unit 1: -32 (exp. 1).
<4>[95206.223544] usb 3-3.4: Warning! Unlikely big volume range (=32767), cval->res is probably wrong.
<4>[95206.223554] usb 3-3.4: [9] FU [Mic Capture Volume] ch = 1, val = -32768/-1/1
<6>[95210.698990] usb 3-3.4: USB disconnect, device number 49
<6>[95211.963090] usb 3-3.4: new high-speed USB device number 50 using xhci_hcd
<6>[95212.657061] usb 3-3.4: new full-speed USB device number 51 using xhci_hcd
<3>[95212.783119] usb 3-3.4: device descriptor read/64, error -32
<3>[95213.015076] usb 3-3.4: device descriptor read/64, error -32
<6>[95213.120358] usb 3-3-port4: attempt power cycle
Bus 001 Device 009: ID 2e1a:4c01 Amba Insta360 Link
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x2e1a
idProduct 0x4c01
bcdDevice 2.00
iManufacturer 1 Amba
iProduct 2 Insta360 Link
iSerial 0
bNumConfigurations 1
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20221101-instal-v1-0-d13d1331c4b5@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The device does not implement the power line frequency control
correctly. It is a UVC 1.5 device, but implements the control as a UVC
1.1 device.
Add the corresponding control mapping override.
Bus 003 Device 002: ID 3277:009e Shine-Optics Integrated Camera
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.01
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x3277
idProduct 0x009e
bcdDevice 0.01
iManufacturer 3 Shine-Optics
iProduct 1 Integrated Camera
iSerial 2 0001
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240108-shine-v2-1-ddff959dab89@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Logitech Rally Bar devices, despite behaving as UVC cameras, have a
different power management system that the other cameras from Logitech.
USB_QUIRK_RESET_RESUME is applied to all the UVC cameras from Logitech
at the usb core. Unfortunately, USB_QUIRK_RESET_RESUME causes undesired
USB disconnects in the Rally Bar that make them completely unusable.
There is an open discussion about if we should fix this in the core or
add a quirk in the UVC driver. In order to enable this hardware, let's
land this patch first, and we can revert it later if there is a
different conclusion.
Fixes: e387ef5c47 ("usb: Add USB_QUIRK_RESET_RESUME for all Logitech UVC webcams")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Devinder Khroad <dkhroad@logitech.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20240404-rallybar-v6-1-6d67bb6b69af@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The Samsung CSIS MIPI receiver provides a start-of-frame interrupt and
a framecount register. As the CSI receiver is the hardware unit that lies
closest to the sensor, the frame counter is the best we can get on these
devices. In case of the ISI available on the i.MX8 M Plus it is also the
only native start-of-frame signal available.
This patch exposes the sof interrupt and the framecount as
V4L2_EVENT_FRAME_SYNC event on the subdevice.
It was tested on a Debix-Som-A with a 6.8-rc4 kernel.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Link: https://lore.kernel.org/r/20240314093652.56923-1-stefan.klug@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
USB urbs must be allocated with usb_alloc_urb. Quoting the manual
Only use this function (usb_init_urb) if you _really_ understand what you
are doing.
Fix the following smatch error:
drivers/media/usb/siano/smsusb.c:53:38: warning: array of flexible structures
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This patch fixes the following checkpatch warnings:
WARNING:PRINTK_WITHOUT_KERN_LEVEL: printk() should include KERN_<LEVEL> facility level
WARNING:PREFER_PR_LEVEL: Prefer [subsystem eg: netdev]_dbg([subsystem]dev, ... then dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ...
WARNING:EMBEDDED_FUNCTION_NAME: Prefer using '"%s...", __func__' to using 'ciintf_slot_ts_enable', this function's name, in a string
CHECK:MACRO_ARG_PRECEDENCE: Macro argument 'level' may be better as '(level)' to avoid precedence issues
There was no consistent style of logging functions used so far.
Convert all logging to the appropriate pr_* macros.
Add a global pr_fmt macro for the whole driver.
Signed-off-by: Stefan Herdler <herdler@nurfuerspam.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This patch fixes the following checkpatch warnings:
WARNING:RETURN_VOID: void function return statements are not generally useful
WARNING:TRAILING_SEMICOLON: macros should not use a trailing semicolon
Signed-off-by: Stefan Herdler <herdler@nurfuerspam.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This patch fixes the following checkpatch warnings:
WARNING:CONSTANT_COMPARISON: Comparisons should place the constant on the right side of the test
Signed-off-by: Stefan Herdler <herdler@nurfuerspam.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This patch fixes the following checkpatch errors:
ERROR:TRAILING_STATEMENTS: trailing statements should be on next line
Signed-off-by: Stefan Herdler <herdler@nurfuerspam.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This patch fixes the following checkpatch errors:
ERROR:ASSIGN_IN_IF: do not use assignment in if condition
Signed-off-by: Stefan Herdler <herdler@nurfuerspam.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This patch fixes the following checkpatch warnings:
WARNING:EXPORT_SYMBOL: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Stefan Herdler <herdler@nurfuerspam.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This patch fixes the following checkpatch warnings and errors:
WARNING:BRACES: braces {} are not necessary for any arm of this statement
WARNING:BRACES: braces {} are not necessary for single statement blocks
ERROR:OPEN_BRACE: that open brace { should be on the previous line
CHECK:BRACES: braces {} should be used on all arms of this statement
CHECK:BRACES: Unbalanced braces around else statement
Signed-off-by: Stefan Herdler <herdler@nurfuerspam.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This patch fixes the following checkpatch warnings:
WARNING:BLOCK_COMMENT_STYLE: Block comments use * on subsequent lines
WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */ on a separate line
WARNING: It's generally not useful to have the filename in the file
Signed-off-by: Stefan Herdler <herdler@nurfuerspam.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
It fixes the following checkpatch errors:
ERROR:SPACING: space prohibited before that ',' (ctx:WxW)
ERROR:SPACING: space required after that ',' (ctx:VxV)
ERROR:SWITCH_CASE_INDENT_LEVEL: switch and case should be at the same indent
This patch contains the large multi line blocks.
Signed-off-by: Stefan Herdler <herdler@nurfuerspam.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This patch fixes the following checkpatch warnings and errors:
ERROR:POINTER_LOCATION: "foo * bar" should be "foo *bar"
ERROR:POINTER_LOCATION: "foo* bar" should be "foo *bar"
ERROR:SPACING: space prohibited after that open parenthesis '('
ERROR:SPACING: space prohibited before that close parenthesis ')'
ERROR:SPACING: space prohibited before that ',' (ctx:WxW)
ERROR:SPACING: space required after that ',' (ctx:VxV)
ERROR:SPACING: space required before that '-' (ctx:OxV)
ERROR:SPACING: space required before the open parenthesis '('
ERROR:SPACING: spaces required around that '!=' (ctx:VxO)
ERROR:SPACING: spaces required around that '<' (ctx:VxV)
ERROR:SPACING: spaces required around that '=' (ctx:VxV)
ERROR:SPACING: spaces required around that '>=' (ctx:VxV)
WARNING:SPACING: space prohibited between function name and open parenthesis '('
WARNING:TABSTOP: Statements should start on a tabstop
WARNING:LEADING_SPACE: please, no spaces at the start of a line
WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements
WARNING:LINE_SPACING: Missing a blank line after declarations
Signed-off-by: Stefan Herdler <herdler@nurfuerspam.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
i2c_device_probe(), seems to assume that irq = 0 means that there is no
irq to request.
The driver also believes that on the clean path. So lets be consistent
here.
Also make smatch happy.
Fix:
drivers/media/i2c/adv7180.c:1526 adv7180_probe() warn: 'client->irq' from request_threaded_irq() not released on lines: 1526
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Simplify a bit the code introducing a new variable for iterating through
the control list.
It also makes smatch happy:
drivers/media/v4l2-core/v4l2-ctrls-api.c:1091 v4l2_query_ext_ctrl() warn: iterator used outside loop: 'ref'
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: fix tiny whitespace issue in 'pos = ref': use just one space]
hva->clk cannot be NULL at this point. Simplify the code and make smatch
happy:
drivers/media/platform/st/sti/hva/hva-hw.c:412 hva_hw_probe() warn: 'hva->clk' from clk_prepare() not released on lines: 412
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add missing release_firmware on the error paths.
drivers/media/usb/dvb-usb/dib0700_devices.c:2415 stk9090m_frontend_attach() warn: 'state->frontend_firmware' from request_firmware() not released on lines: 2415.
drivers/media/usb/dvb-usb/dib0700_devices.c:2497 nim9090md_frontend_attach() warn: 'state->frontend_firmware' from request_firmware() not released on lines: 2489,2497.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Do not cache the file, instead load it on demand.
This makes smatch a happy parser:
drivers/media/dvb-frontends/drx39xyj/drxj.c:11908 drx_ctrl_u_code() warn: 'fw' from request_firmware() not released on lines: 11877,11886,11896.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Make sure the firmware is released when we leave
xc_load_fw_and_init_tuner()
This change makes smatch happy:
drivers/media/tuners/xc5000.c:1213 xc_load_fw_and_init_tuner() warn: 'fw' from request_firmware() not released on lines: 1213.
Cc: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
release_firmware() in the same function that it was requested. It is
more clear and makes smatch happy.
drivers/media/platform/st/sti/c8sectpfe/c8sectpfe-core.c:1146 load_c8sectpfe_fw() warn: 'fw' from request_firmware() not released on lines: 1125,1132.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The handled version of request_irq let us remove the free_irq and makes
smatch happier:
drivers/media/pci/saa7134/saa7134-alsa.c:1186 alsa_card_saa7134_create() warn: 'dev->pci->irq' from request_irq() not released on lines: 1186
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Let devm handle the life cycle of the irq request.
Makes smatch happier:
drivers/media/pci/solo6x10/solo6x10-core.c:631 solo_pci_probe() warn: 'pdev' from pci_request_regions() not released on lines: 631.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Instead of handling manually the release of the memory regions let devm
do that for us.
Makes smatch happy:
drivers/media/pci/solo6x10/solo6x10-core.c:631 solo_pci_probe() warn: 'pdev' from pci_request_regions() not released on lines: 631.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This structure is embedded in multiple other structures that are packed,
which conflicts with it being aligned.
drivers/media/usb/as102/as10x_cmd.h:379:30: warning: field reg_addr within 'struct as10x_dump_memory::(unnamed at drivers/media/usb/as102/as10x_cmd.h:373:2)' is less aligned than 'struct as10x_register_addr' and is usually due to 'struct as10x_dump_memory::(unnamed at drivers/media/usb/as102/as10x_cmd.h:373:2)' being packed, which can lead to unaligned accesses [-Wunaligned-access]
Mark it as being packed.
Marking the inner struct as 'packed' does not change the layout, since the
whole struct is already packed, it just silences the clang warning. See
also this llvm discussion:
https://github.com/llvm/llvm-project/issues/55520
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Make dependency on DEBUG_FS conditional, that way we are not forced to
enable DEBUG_FS if we can to use this driver.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When support for streams was added to the V4L2 subdev API, the
v4l2_subdev_crop structure was extended with a stream field, but the
field was not handled in the core code that translates the
VIDIOC_SUBDEV_[GS]_CROP ioctls to the selection API. Fix it.
Fixes: 2f91e10ee6 ("media: subdev: add stream based configuration")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The graph walk tries to follow all links, even if they are not between
pads. This causes a crash with, e.g. a MEDIA_LNK_FL_ANCILLARY_LINK link.
Fix this by allowing the walk to proceed only for MEDIA_LNK_FL_DATA_LINK
links.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: stable@vger.kernel.org # for 6.1 and later
Fixes: ae21987283 ("media: mc: entity: Rewrite media_pipeline_start()")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Remove e-mail addresses that are no longer valid.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Using __exit for the remove function results in the remove callback
being discarded with CONFIG_VIDEO_ET8EK8=y. When such a device gets
unbound (e.g. using sysfs or hotplug), the driver is just removed
without the cleanup being performed. This results in resource leaks. Fix
it by compiling in the remove callback unconditionally.
This also fixes a W=1 modpost warning:
WARNING: modpost: drivers/media/i2c/et8ek8/et8ek8: section mismatch in reference: et8ek8_i2c_driver+0x10 (section: .data) -> et8ek8_remove (section: .exit.text)
Fixes: c5254e72b8 ("[media] media: Driver for Toshiba et8ek8 5MP sensor")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
ipu-cio2 uses generic power management, and pci_pm_runtime_suspend() and
pci_pm_runtime_resume() already take care of setting the PCI device power
state, so the driver doesn't need to do it explicitly.
Remove explicit setting to D3hot or D0 during runtime suspend and resume.
Remove #defines that are no longer used.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Hyungwoo Yang <hyungwoo.yang@intel.com>
Cc: Rajmohan Mani <rajmohan.mani@intel.com>
Cc: Vijaykumar Ramya <ramya.vijaykumar@intel.com>
Cc: Samu Onkalo <samu.onkalo@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Jouni Ukkonen <jouni.ukkonen@intel.com>
Cc: Antti Laakso <antti.laakso@intel.com>
[Sakari Ailus: Remove now-redundant local variables.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Since commit 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint
property verification") the ov2680 no longer probes on a imx7s-warp7:
ov2680 1-0036: error -EINVAL: supported link freq 330000000 not found
ov2680 1-0036: probe with driver ov2680 failed with error -22
As the 'link-frequencies' property is not mandatory, allow the probe
to succeed by skipping the link-frequency verification when the
property is absent.
Cc: stable@vger.kernel.org
Fixes: 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint property verification")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Since commit 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint
property verification") even when the correct 'link-frequencies'
property is passed in the devicetree, the driver fails to probe:
ov2680 1-0036: probe with driver ov2680 failed with error -22
The reason is that the variable 'ret' may contain the -EINVAL value
from a previous assignment:
ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
&rate);
Fix the problem by clearing 'ret' on the successful path.
Tested on imx7s-warp board with the following devicetree:
port {
ov2680_to_mipi: endpoint {
remote-endpoint = <&mipi_from_sensor>;
clock-lanes = <0>;
data-lanes = <1>;
link-frequencies = /bits/ 64 <330000000>;
};
};
Cc: stable@vger.kernel.org
Fixes: 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint property verification")
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The driver dug the supported link frequency up from the V4L2 fwnode
endpoint and used it internally, but failed to report this in the
LINK_FREQ and PIXEL_RATE controls. Fix this.
Fixes: 0677a2d9b7 ("media: ov2740: Add support for 180 MHz link frequency")
Cc: stable@vger.kernel.org # for v6.8 and later
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The notifier_entry of a notifier is not re-initialised after unregistering
the notifier. This leads to dangling pointers being left there so use
list_del_init() to return the notifier_entry an empty list.
Fixes: b8ec754ae4 ("media: v4l: async: Set v4l2_device and subdev in async notifier init")
Cc: <stable@vger.kernel.org> # for 6.6 and later
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The V4L2 device used to be set when the notifier was registered but this
has been moved to the notifier initialisation. Don't touch the V4L2 device
if registration fails.
Fixes: b8ec754ae4 ("media: v4l: async: Set v4l2_device and subdev in async notifier init")
Cc: <stable@vger.kernel.org> # for 6.6 and later
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
struct v4l2_async_notifier has several list_head members, but only
waiting_list and done_list are initialized. notifier_entry was kept
'zeroed' leading to an uninitialized list_head.
This results in a NULL-pointer dereference if csi2_async_register() fails,
e.g. node for remote endpoint is disabled, and returns -ENOTCONN.
The following calls to v4l2_async_nf_unregister() results in a NULL
pointer dereference.
Add the missing list head initializer.
Fixes: b8ec754ae4 ("media: v4l: async: Set v4l2_device and subdev in async notifier init")
Cc: <stable@vger.kernel.org> # for 6.6 and later
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Call devm_request_irq() before registering the async notifier, as otherwise
it would be possible to use the device before the interrupts could be
delivered to the driver.
Fixes: c2a6a07afe ("media: intel-ipu3: cio2: add new MIPI-CSI2 driver")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
After the conversion of dv timing calls to use a pad argument is done,
remove the old callbacks. Update the subdev ioctl handlers to use the
new callbacks.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the pad variant for all (s|g|query)_dv_timings subdev calls, which
includes a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the pad variant for all (s|g|query)_dv_timings subdev calls, which
includes a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the pad variant for all (s|g|query)_dv_timings subdev calls, which
includes a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the pad variant for all (s|g|query)_dv_timings subdev calls, which
includes a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Currently, subdev dv timing calls (i.e. g/s/query_dv_timings) are video
ops without a pad argument. This is a problem if the subdevice can have
different dv timings for each pad (e.g. a DisplayPort receiver with
multiple virtual channels).
To solve this, change these calls to include a pad argument, and put
them into pad ops. Keep the old ones temporarily to make the switch
easier.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
vfe-170 and vfe-175 can be supported in the same file with some minimal
indirection to differentiate between the silicon versions.
sdm845 uses vfe-170, sc8280xp uses vfe-175-200. Lets rename the file to
capture its wider scope than vfe-170 only.
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add in functional logic throughout the code to support the sc8280xp.
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This commit describes the hardware layout for the sc8280xp for the
following hardware blocks:
- 4 x VFE, 4 RDI per VFE
- 4 x VFE Lite, 4 RDI per VFE
- 4 x CSID
- 4 x CSID Lite
- 4 x CSI PHY
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Adds a CAMSS SoC identifier for the SC8280XP.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a PHY configuration sequence for the sc8280xp which uses a Qualcomm
Gen 2 version 1.1 CSI-2 PHY.
The PHY can be configured as two phase or three phase in C-PHY or D-PHY
mode. This configuration supports two-phase D-PHY mode.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Instead of using fallback driver name match, provide ID table[1] for the
primary match.
[1]: https://elixir.bootlin.com/linux/v6.8/source/drivers/base/platform.c#L1353
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This driver's initialization functions do not perform any custom code,
except printing messages. Printing messages on modules
loading/unloading is discouraged because it pollutes the dmesg
regardless whether user actually has this device. Core kernel code
already gives tools to investigate whether module was loaded or not.
Drop the printing messages which allows to replace open-coded
module_sdio_driver().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Because the size passed to copy_from_user() cannot be known beforehand,
it needs to be checked during runtime with check_object_size. That makes
gcc believe that the content of sbuf can be used before init.
Fix:
./include/linux/thread_info.h:215:17: warning: ‘sbuf’ may be used uninitialized [-Wmaybe-uninitialized]
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Increase the size of led_names so it can fit any valid v4l2 device name.
Fixes:
drivers/media/radio/radio-shark2.c:197:17: warning: ‘%s’ directive output may be truncated writing up to 35 bytes into a region of size 32 [-Wformat-truncation=]
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
clang-19 warns about mixing two enum types here:
drivers/media/platform/renesas/rcar-vin/rcar-vin.h:296:12: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
drivers/media/platform/renesas/rcar-vin/rcar-core.c:216:18: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
drivers/media/platform/renesas/rcar-vin/rcar-vin.h:296:12: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
drivers/media/platform/renesas/rcar-vin/rcar-vin.h:296:12: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
This one is intentional, and there is already a cast to work around another
warning, so address this by adding another cast.
Fixes: 406bb586de ("media: rcar-vin: Add r8a779a0 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
According to the formats description in videodev2.h Y210, Y212 and Y216
are YCbCr packed formats. For each Y2xx format, xx bits of valid data
occupy the MSBs of the 16 bit components, and 16-xx bits of zero padding
occupy the LSBs.
The Y210 and Y216 formats are missing an entry in the v4l2_format_info[]
table. Add it.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add terminating new line to the Kconfig file.
Signed-off-by: Prasad Pandit <pjp@fedoraproject.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: dropped 'Fixes' tag, not relevant for this]
A 'case V4L2_CTRL_TYPE_AREA' was missing in v4l2_ctrl_type_op_log,
which led to an 'unknown type' message in the kernel log.
Add support for controls of this type.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The return value of dvb_ca_en50221_init() is not checked here that may
cause undefined behavior in case of nonzero value return.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 25aee3debe ("[media] Rename media/dvb as media/pci")
Signed-off-by: Aleksandr Burakov <a.burakov@rosalinux.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
anysee_master_xfer currently accepts read messages of length 2 only.
However, several frontends, e.g. tda10023 send buffers of length 1,
containing an 8-bit register number (see tda10023_readreg).
These buffers are rejected currently, making many Anysee variants
to not work. In these cases the "Unsupported Anysee version"
message is logged.
This patch alters the function to accept buffers of a length of 1 too.
Signed-off-by: István Váradi <ivaradi@varadiistvan.hu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: add spaces around '<', fix typo in 'sevaral']
The physical address on the MT8188 platform is larger than 32 bits,
change the type from unsigned int to dma_addr_t to be able to access
the high bits of the address.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a lock for the ctx_list, to avoid accessing a NULL pointer
within the 'vpu_enc_ipi_handler' function when the ctx_list has
been deleted due to an unexpected behavior on the SCP IP block.
Fixes: 1972e32431 ("media: mediatek: vcodec: Fix possible invalid memory access for encoder")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The VP9 bitstream uses superframes, which each contain 8 sub-frames,
enable accessing the last superframe by increasing the range of the index
vaidation as the maximum number of superframes is 8 and not 7, so that the
last sub-frame can be decoded normally with the stateful VP9 decoder.
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Allow to remove buffers on capture queue because it the one which
own the decoded buffers. After a dynamic resolution change lot of
them could remain allocated but won't be used anymore so deleting
them save memory.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Create v4l2-mem2mem helpers for VIDIOC_REMOVE_BUFS ioctl and
make test drivers use it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
VIDIOC_REMOVE_BUFS ioctl allows to remove buffers from a queue.
The number of buffers to remove in given by count field of
struct v4l2_remove_buffers and the range start at the index
specified in the same structure.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: vidioc-remove-bufs.rst: mention no bufs are freed on error]
Improve __vb2_queue_free() and __vb2_free_mem() to free
range of buffers and not only the last few buffers.
Introduce starting index to be flexible on range and change the loops
according to this parameter.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a bitmap field to know which of bufs array entries are
used or not.
Remove no more used num_buffers field from queue structure.
Use bitmap_find_next_zero_area() to find the first possible
range when creating new buffers to fill the gaps.
If no suitable range is found try to allocate less buffers
than requested.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When REMOVE_BUFS will be introduced holes could created in bufs array.
To be able to reuse these unused indices reworking how create->index
is set is mandatory.
Let __vb2_queue_alloc() decide which first index is correct and
forward this to the caller.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Instead of using 'min_queued_buffers' field to specify the
minimum number of buffers to be allocated when calling REQBUF
use 'min_reqbufs_allocation' field which is dedicated to this
purpose.
Change the minimum requested buffers to 2 for vivid-meta-out
and vivid-touch-cap drivers when creating the queues.
That allows to remove code which prohibe to allocate only
one buffer in their respective queue setup functions.
While at it rename vivid_create_queue() parameter.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add 'min_reqbufs_allocation' field in the vb2_queue structure so drivers
can specify the minimum number of buffers to allocate when calling
VIDIOC_REQBUFS.
When initializing the queue, v4l2 core makes sure that the following
constraints are respected:
- the minimum number of buffers to allocate must be at least 2 because
one buffer is used by the hardware while the other is being processed
by userspace.
-if the driver needs 'min_queued_buffers' in the queue before calling
start_streaming(), then the minimum requirement is 'min_queued_buffers + 1'
to keep at least one buffer available for userspace.
Simplify __vb2_init_fileio() by using 'min_reqbufs_allocation' directly
to avoid duplicating the minimum number of buffers to allocate computation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Do not rely on the number of allocated buffers to know if the
queue is busy but on a flag set when at least one buffer has been allocated
by REQBUFS or CREATE_BUFS ioctl.
The flag is reset when REQBUFS is called with count = 0 or the file
handle is closed.
This is needed because remove buffers feature will be able to remove
all the buffers from a queue while streaming so relying on the number
of allocated buffers in the queue won't be possible.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
sprintf() will be converted as weel if they have.
Generally, this patch is generated by
make coccicheck M=<path/to/file> MODE=patch \
COCCI=scripts/coccinelle/api/device_attr_show.cocci
No functional change intended
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Since commit 43a7206b09 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the lirc_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Unify the indentation and multi-line comment style.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Remove trailing comma in the terminator entry in ID table(s).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
We have a temporary variable to keep pointer to struct device.
Utilise it inside the ->probe() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Update header inclusions to follow IWYU (Include What You Use)
principle.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
