Since the ->enable() callback is called with a spinlock held, we cannot
call potentially blocking functions such as clk_get_rate() or
clk_get_parent(), so use the unlocked versions instead.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
[rklein: Adapted from ChromeOS patch, removing pllu_enable cleanup as
it isn't present upstream]
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When adding the nvenc clock, it was partially named msenc in the code.
Since the msenc clock isn't present in Tegra210 and has been replaced by
the nvenc clock, its misleading to see it present. Therefore, properly
rename it.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some register for PLLM and PLLMB were named MISC0 but according to the
TRM, they have different names. Sync up the names to make it easier to
understand which register they are really referring to.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A83T has similar bus gates that of H3, including single gating register has
different clock parent.
As per H3 and A83T datasheet, usbhost is under AHB2.
However,below shows allwinner source code assignment:
bits: 26 (ehci0), 27 (ehci1), 29 (ohci0) => AHB1 for A83T.
bits: 26 (ehci0), 27 (ehci1) => AHB1 for H3
bits 29, 30, 31(ohci0,1,2) => AHB2 for H3.
until, this confusion is cleared keep it H3 way.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
APB0 is part of PRCM, and is compatible with earlier SOCs.
apb0 gates controls R_PIO, R_UART, R_RSB, etc clocks.
This patch adds support for APB0 gates for A83T.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These three cases let clk_register() fail. They should be considered
as error messages.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The core->parents is a cache to save expensive clock parent look-ups.
It will be filled as needed later. We do not have to do it here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Drop the "if (!core->parents)" case and refactor the function a bit
because core->parents is always allocated. (Strictly speaking, it is
ZERO_SIZE_PTR if core->num_parents == 0, but such a case is omitted
by the if-conditional above.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently, __clk_core_init() allows failure of the kcalloc() for the
core->parents. So, clk_fetch_parent_index() and __clk_init_parent()
also try to allocate core->parents in case it has not been allocated
yet. Scattering memory allocation here and there makes things
complicated.
Like other clk_core members, allocate core->parents in clk_register()
and let it fail in case of memory shortage. If we cannot allocate
such a small piece of memory, the system is already insane. There is
no point to postpone the memory allocation.
Also, allocate core->parents regardless of core->num_parents. We want
it even if core->num_parents == 1 because clk_fetch_parent_index()
might be called against the clk_core with a single parent.
If core->num_parents == 0, core->parents is set to ZERO_SIZE_PTR. It
is harmless because no access happens to core->parents in such a case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now, the clock parent is not "struct clk *", but "struct clk_core *".
Of course, the size of a pointer is always same, but strictly speaking,
sizeof(struct clk *) should be sizeof(struct clk_core *) here.
This mismatch happened when we split the structure into struct clk
and struct clk_core. For the potential possibility of future renaming,
sizeof(*core->parents) would be better.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This if-block has been here since the introduction of the common
clock framework. Now no clock drivers are statically initialized.
core->parent is always NULL at this point. Drop the redundant
check and the confusing comment.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now this function takes clk_core as its argument. __clk_core_init()
would be more suitable for the name of this function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The argument clk_user is used only for the clk_user->core. The rest
of this function only takes care of clk_core.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The "struct device *dev" is not used at all in this function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We should not dereference registers as pointers, so use readl/writel
instead for these registers.
The clock registers are accessed in multiple files, so we have to
change them all at once.
I stumbled over these registers while looking at something unrelated.
There are in fact other registers with the same problem, but I did
not try to address those at this point.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Also rename the external input for the emac on rk3036, which
should still be ok to do, as that binding was only introduced
during this merge-window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWm9wLAAoJEPOmecmc0R2BfbUIAI7VaIzwhl4NkAO3x0P6emZT
B/2C4RuPLW9oBf/YGxG+HsxD2iLpDjAlZADlGBXsrdkfjFuN0iULc8COrFJEGv0F
HuFmxJz7IZCNS4BgXt+vk0yb43c1lLSMRSmTyWaY7izYUlQtcmDp/t7zTvwun9NM
N2U44zXFsEnTtsb3gV65PivrMBT/sNK9MyOIylh3Xjs/v+fTCtsHwPVckFwiIiPx
ER9ETDmeo/DEMtsutHTlCcujyvZXE3jsho0Ow7J/vuRJSbXkCW+Ki9CQZEvHGWXL
7ZaST8A8LEBjvslCh9IkirZ7qi20wwk/md3zAeoE0+eimEOEIqWYF8qwsWHiJjU=
=oT+p
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rockchip-clkfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-fixes
Pull rockchip fixes from Heiko Stuebner:
Fixes for wrong register offsets in both rk3036 and rk3368.
Also rename the external input for the emac on rk3036, which
should still be ok to do, as that binding was only introduced
during this merge-window.
* tag 'v4.5-rockchip-clkfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: rk3368: fix some clock gates
clk: rockchip: rk3036: rename emac ext source clock
clk: rockchip: rk3036: fix the div offset for emac clock
clk: rockchip: rk3036: fix uarts clock error
clk: rockchip: rk3036: fix the FLAGs for clock mux
My previous patch fixed some warnings about printing a couple
of variables that are always uninitialized in quadfs_pll_fs660c32_set_rate(),
but I now got a warning that only shows up in some configurations (i.e.
without gcc -Os) about the params.ndiv being used uninitialized in the
error case:
drivers/clk/st/clkgen-fsyn.c: In function 'quadfs_pll_fs660c32_set_rate':
drivers/clk/st/clkgen-fsyn.c:584:75: warning: 'params.ndiv' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/clk/st/clkgen-fsyn.c:574:16: note: 'params.ndiv' was declared here
This changes the error handling so we bail for invalid arguments rather
than continuing with uninitialized data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The size of unsigned long on 64-bit architectures is equal to the
size of u64, so this check is impossible there. This throws off
static checkers:
drivers/clk/clk-axi-clkgen.c:331 axi_clkgen_recalc_rate() warn:
impossible condition '(tmp > (~0)) => (0-u64max > u64max)'
Let's change this code to use min_t() instead so that we
get the same effect on architectures where sizeof(unsigned long)
doesn't equal sizeof(u64).
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clock generator has two clock inputs that can be used as the reference
clock. Add support for switching between them at runtime.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Version 1 of the axi-clkgen core has not been used in new designs for over
two years now. This is a soft peripheral used in FPGAs and anybody who has
updated their kernel to the latest version will also have updated the
bitstream containing the clock generator. So it should be safe to drop
support for this now.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Even if the probability of this case is very low, fixing it made
static analyzers happy.
Solving this with of_device_get_match_data made also code simplier.
Reported-by: coverity (CID 1324137)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The palmas_clks_of_match_data structures are never modified.
This patch constify them.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Because _next_div() returns a valid divider, there is no need to
consult _is_valid_div() for the validity of the divider in every
iteration.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
With unsigned values underflow in loops can occur resulting in
theoretically infinite loops.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clock is required for loading the qdsp firmware.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove __init macro from all function prototypes in clk-iproc.h
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for Broadcom Cygnus audio PLL and leaf
clocks
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Move all vendor's Kconfig into CCF menu section to prevent
new drivers putting their Kconfig files in a wrong place.
Some Kconfigs need to be modified at the same time to avoid build
warnings.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[sboyd@codeaurora.org: Fix typos in commit message]
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
mtk_clk_register_composite() may leak memory due to some error
handling path don't free all allocated memory. This patch
free all pointers that may allocate memory before error return.
And it's safe because kfree() can handle NULL pointers.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
to_clk_*(_hw) macros have been repeatedly defined in many places.
This patch moves all the to_clk_*(_hw) definitions in the common
clock framework to public header clk-provider.h, and drop the local
definitions.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This function doesn't return anything because it's void. Drop the
return statement.
Cc: Loc Ho <lho@apm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add X-Gene SoC and PMD PLL clocks support for v2 hardware.
X-Gene SoC v2 and above use an slightly different SoC
and PMD PLL hardware logic.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The definition of s2mps11_name is meant to resolve the name of a
given clock. Remove it because the clocks have the same name we
can get it directly from the s2mps11_clks_init structure.
While in the probe function the s2mps11_clks is used only to
iterate through the s2mps11_clks. The naming itself brings
confusion and the readability does not improve much.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clk_table and clk_data are declared static. The clk_table
contains the three clock data structures belonging to the s2mps11
driver. In the probe function it gets stored into clk_data.
Remove clk_table and refer directly to clk_data.
clk_data, itself, is also declared static. Declare locally it
and allocate it inside the probe function, as it is not used
anywhere else.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The driver allocates three structures, s2mpsxx_clk_init, for
three different clock types (s2mps11, s2mps13 and s2mps14). They
are quite similar but they differ only by the name. Only one of
these structures is used, while the others lie unused in the
memory.
The clock's name, though, is not such a meaningful information
and by assigning the same name to the initial data we can avoid
over allocation. The common name chosen will be s2mps11,
coherently with the device driver name, instead of the clock
device.
Therefore, remove the structures associated to s2mps13 and
s2mps14 and use only the one referred to s2mps11 for all kind of
clocks.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The driver already loops once, there is no reason to loop again
for a different purpose. Merge the second loop into the first.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Commit e6d5e7d90b ("clk-divider: Fix READ_ONLY when divider > 1") removed
the special ops struct for read-only clocks and instead opted to handle
them inside the regular ops.
On the rk3368 this results in breakage as aclkm now gets set a value.
While it is the same divider value, the A53 core still doesn't like it,
which can result in the cpu ending up in a hang.
The reason being that "ACLKENMasserts one clock cycle before the rising
edge of ACLKM" and the clock should only be touched when STANDBYWFIL2
is asserted.
To fix this, reintroduce the read-only ops but do include the round_rate
callback. That way no writes that may be unsafe are done to the divider
register in any case.
The Rockchip use of the clk_divider_ops is adapted to this split again,
as is the nxp, lpc18xx-ccu driver that was included since the original
commit. On lpc18xx-ccu the divider seems to always be read-only
so only uses the new ops now.
Fixes: e6d5e7d90b ("clk-divider: Fix READ_ONLY when divider > 1")
Reported-by: Zhang Qing <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
platform_device_register_simple() returns ERR_PTR on error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
sun8i-a23-mbus-clk used sunxi's factors clk, which is nice for very
complicated clocks, but is not really needed here.
Convert sun8i-a23-mbus-clk to use clk_composite, as it is a gate + mux
+ divider. This makes the code easier to understand.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The factors clk implementation has been extended to support custom
recalc callbacks to support clocks that use one factor for certain
parents only, like a pre-divider.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The common clock framework requires either determine_rate or round_rate
to be implemented. We use determine_rate so we can pass the parent index
to the get_factors callback. This cannot be done easily with round_rate,
so just drop it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clocks cannot be modelled using the standard factors clk formula,
such as clocks with special pre-dividers on one parent, or clocks
with all power-of-two dividers.
Add support for a custom .recalc callback for factors clk. Also pass
the current parent index to the .get_factor and .recalc callbacks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allow sclk_i2s0 and i2s0_frac to change their parents rate as
that the upstream dividers are purely there to feed sclk_i2s0
Tested on radxarock-lite.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
mmc sample shift is 0 for rk3228 refer to user manaul.
So it's broken if we enable mmc tuning for rk3228.
Fixes: 307a2e9ac ("clk: rockchip: add clock controller for rk3228")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The .get_factors callback of factors_clk has 6 parameters. To extend
factors_clk in any way that requires adding parameters to .get_factors
would make that list even longer, not to mention changing all the
function declarations.
Do this once now and consolidate all the parameters into a struct.
Also drop the space before function pointer arguments, since checkpatch
complains.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sunxi's factors clk did not have an unregister function. This means
multiple structs were leaked whenever a factors clk was unregistered.
Add an unregister function for it. Also keep pointers to the mux and
gate structs so they can be freed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sunxi_factors_register() does not check for failures or cleanup after
clk_register_composite() or other clk-related calls.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
struct clk_factors_config contains shifts/widths for the factors of
the factors clk. This is used to read out the factors from the register
value. In no case is it written to, so make it const.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
hclk_cpubus needs to keep running because it is needed for devices like
the rom, i2s0 or spdif to be accessible via cpu. Without that all
accesses to devices (readl/writel) return wrong data. So add it
to the list of critical clocks.
Fixes: 78eaf6095c ("clk: rockchip: disable unused clocks")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Cc: stable@vger.kernel.org # 4.1.x-
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Set clock id for sclk_tsadc gating clock of tsadc in rk3066
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The otgphy clocks really only drive the phy blocks. These in turn
contain plls that then generate the 480m clocks the clock controller
uses to supply some other clocks like uart0, gpu or the video-codec.
So fix this structure to actually respect that hirarchy and removed
that usb480m fixed-rate clock working as a placeholder till now, as
this wouldn't even work if the supplying phy gets turned off while
its pll-output gets used elsewhere.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Most PLL's don't actually have LOCK_ENABLE bits. However, most PLL's
also had that flag set, which meant that the clk code was trying to
enable locks, and inadvertantly flipping bits in other fields.
For PLLM, ensure the correct register is used for the misc_register.
PLL_MISC0 contains the EN_LCKDET bit which should be used for enabling
the lock, and PLLM_MISC1 shouldn't be used at all.
Lastly, remove some of the settings which would point to the EN_LCKDET
bits for some PLLs. There is no need to enable the locks, and that is
done as part of the set_defaults logic already.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
VI-I2C has 16 bits available for its divider. Switch the divider width
to 16 instead of 8 so correct rates can be set.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
I2S_2CH set freq need to select parent and calculate parent freq.
so just mark it as the CLK_SET_RATE_PARENT flag.
Signed-off-by: zhangqing <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
SPDIF_8CH set freq need to select parent and calculate parent freq.
so just mark it as the CLK_SET_RATE_PARENT flag.
Signed-off-by: zhangqing <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The edp_24m parent select bit define is:
1'b0:xin24m
1'b1:1'b0(dummy)
so adapt the parent sel bit to the currect one.
Signed-off-by: zhangqing <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The latest addition of H3 USB clocks placed them at the bottom. Move it
before A80 (sun9i), so they are sorted by SoC family then name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This file is a clock provider, not a clk consumer. Drop the clk.h
include.
Cc: Jens Kuske <jenskuske@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The vdpu and vepu clocks can also be parented to the npll and current
parent list also is wrong as it would use the npll as "usbphy" source,
so adapt the parent to the correct one.
Fixes: 3536c97a52 ("clk: rockchip: add rk3368 clock controller")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: zhangqing <zhangqing@rock-chips.com>
Cc: stable@vger.kernel.org
Similar to commit 9880d4277f ("clk: rockchip: fix rk3288 cpuclk core
dividers") it seems the cpuclk dividers are one to high on the rk3368
as well.
And again similar to the previous fix, we opt to make the divider list
contain the values to be written to use the same paradigm for them on all
supported socs.
Fixes: 3536c97a52 ("clk: rockchip: add rk3368 clock controller")
Reported-by: Zhang Qing <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: zhangqing <zhangqing@rock-chips.com>
Cc: stable@vger.kernel.org
Both clusters have their mux bit in bit 7 of their respective register.
For whatever reason the big cluster currently lists bit 15 which is
definitly wrong.
Fixes: 3536c97a52 ("clk: rockchip: add rk3368 clock controller")
Reported-by: Zhang Qing <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: zhangqing <zhangqing@rock-chips.com>
Cc: stable@vger.kernel.org
HCLK_VIO_BUS is the noc bus controller clock for display module,
due to it shouldn't belong to any driver, but we need it enabled,
so just mark it as the CLK_IGNORE_UNUSED flag.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a crisp
overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XDLa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings several
of the more minor and older platforms we have closer to multiplatform
support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview
Much of this is moving around header files from old mach directories,
but there are also some cleanup patches of debug_ll (lowlevel debug
per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1AW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform so these
can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W+es
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-urgent ARM SoC fixes from Olof Johansson:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform
so these can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: Fix randconfig build warning for dm814_pllss_data
ARM: sa1100/simpad: Be sure to clamp return value
ARM: scoop: Be sure to clamp return value
ARM: davinci: fix a problematic usage of WARN()
ARM: davinci: only select WT cache if cache is enabled
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
MAINTAINERS: gpio-brcmstb: Remove stray '>'
MAINTAINERS: brcmstb: Include Broadcom internal mailing-list
The asm-generic tree this time contains one series from Nicolas Pitre
that makes the optimized do_div() implementation from the ARM
architecture available to all architectures. This also adds stricter
type checking for callers of do_div, which has uncovered a number
of bugs in existing code, and fixes up the ones we have found.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4psa
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"The asm-generic tree this time contains one series from Nicolas Pitre
that makes the optimized do_div() implementation from the ARM
architecture available to all architectures.
This also adds stricter type checking for callers of do_div, which has
uncovered a number of bugs in existing code, and fixes up the ones we
have found"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
ARM: asm/div64.h: adjust to generic codde
__div64_32(): make it overridable at compile time
__div64_const32(): abstract out the actual 128-bit cross product code
do_div(): generic optimization for constant divisor on 32-bit machines
div64.h: optimize do_div() for power-of-two constant divisors
mtd/sm_ftl.c: fix wrong do_div() usage
drm/mgag200/mgag200_mode.c: fix wrong do_div() usage
hid-sensor-hub.c: fix wrong do_div() usage
ti/fapll: fix wrong do_div() usage
ti/clkt_dpll: fix wrong do_div() usage
tegra/clk-divider: fix wrong do_div() usage
imx/clk-pllv2: fix wrong do_div() usage
imx/clk-pllv1: fix wrong do_div() usage
nouveau/nvkm/subdev/clk/gk20a.c: fix wrong do_div() usage
Reference to the Rockchip RK3368 TRM v1.1, some clock
gates need to be updated.
Signed-off-by: Jianqun xu <jay.xu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There is only support rmii in the RK3036, so we should use the correct
ext clock name as described in the TRM.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
[update dt-binding document as well]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Due to reference to old version TRM, there are incorrect emac clock node.
The SEL_21_9 is used for the parent div, the SEL_21_4 is used for the
child div.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Due to a copy-paste error the uart1 and uart2 clock div set
incorrect, fix it.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The DFLAGS are used for the clock dividers, the CLKSEL_CON flags
of COMPOSITE_NODIV type should be MFLAGS.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Presumably the second COMMON_CLK_NXP config option in
drivers/clk/Kconfig appeared after a merge conflict resolution, remove
the wrong record of two.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This set of changes adds support for the Tegra210 SoC and contains a
couple fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/f1y
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.5-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.5-rc1
This set of changes adds support for the Tegra210 SoC and contains a
couple fixes and cleanups.
When the clock DT property is not given, of_clk_get_parent_count()
returns -ENOENT, which then tries to allocate -2 x 4 bytes of memory,
which of course fails, causing the whole driver to fail to create
the clock.
This causes the SolidRun platforms to fail probing the SDHCI1 interface
which is connected to the WiFi.
Fix this by detecting errno codes, skipping the allocation, and fixing
of_clk_gpio_gate_delayed_register_get() to handle a NULL parent_names
array.
Fixes: 80eeb1f0f7 ("clk: add gpio controlled clock multiplexer")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
To model the muxes downstream of fractional dividers we introduced the
child property, allowing to describe a direct child clock.
The first implementation seems to cause section warnings, as the core
clock-tree is marked as initdata while the data pointed to from the
child element is not.
While there may be some way to also set that missing property in the
inline notation I didn't find it, so to actually fix the issue for now
move the sub-definitions into separate declarations that can have
their own __initdata properties.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
We might make bad memory allocations if we get (e.g.) -ENOSYS from
of_clk_get_parent_count().
Noticed by Coverity.
Fixes: f66541ba02 ("clk: gpio: Get parent clk names in of_gpio_clk_setup()")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Sergej Sawazki <ce3a@gmx.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
If we fail to allocate parent_name then we are returning but we missed
freeing data which has already been allocated.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
1. eMMC/SDIO minor fixes usage of bindings on Snow and Peach
Chromebooks.
2. Remove FIMD from Odroid XU3-family because on XU3 it cannot be used
yet and on XU3-Lite and XU4 it is not supported.
3. Remove deprecated since June 2013 samsung,exynos5-hdmi.
4. Add support for Pseudo Random Generator on Exynos4 (Trats2 for now).
This depends on new SSS clock.
5. Add rotator nodes for Exynos4 and Exynos5.
6. Switch DWC3_1 on Odroid XU3 and XU3-Lite to peripheral mode because
now it cannot be used as OTG.
7. Cleanup the G2D usage on Exynos4 and add it to a proper domain
in case of Exynos4210.
8. Put MDMA1 in proper domain on Exynos4210 as well.
9. Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LMzD
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Merge "Samsung DeviceTree updates and improvements for 4.5" from Krzysztof Kozlowski:
1. eMMC/SDIO minor fixes usage of bindings on Snow and Peach
Chromebooks.
2. Remove FIMD from Odroid XU3-family because on XU3 it cannot be used
yet and on XU3-Lite and XU4 it is not supported.
3. Remove deprecated since June 2013 samsung,exynos5-hdmi.
4. Add support for Pseudo Random Generator on Exynos4 (Trats2 for now).
This depends on new SSS clock.
5. Add rotator nodes for Exynos4 and Exynos5.
6. Switch DWC3_1 on Odroid XU3 and XU3-Lite to peripheral mode because
now it cannot be used as OTG.
7. Cleanup the G2D usage on Exynos4 and add it to a proper domain
in case of Exynos4210.
8. Put MDMA1 in proper domain on Exynos4210 as well.
9. Minor cleanups.
* tag 'samsung-dt-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (21 commits)
ARM: dts: Unify G2D device node with other devices on exynos4
ARM: dts: Add power domain to G2D device on exynos4210
ARM: dts: MDMA1 device belongs to LCD0 power domain on exynos4210
ARM: dts: Remove unneeded GPIO include in exynos4412-odroidu3
ARM: dts: exynos4210-universal_c210: Disable DMA for UARTs
ARM: dts: Use peripheral mode for dwc3_1 on exynos5422-odroidxu3
ARM: dts: Add rotator node on exynos5420
ARM: dts: Add rotator node on exynos5250
ARM: dts: Fix power domain for sysmmu-rotator device on exynos4
ARM: dts: Add rotator nodes on exynos4
ARM: dts: Enable PRNG module on exynos4412-trats2
ARM: dts: Add PRNG module for exynos4
dt-bindings: remove deprecated compatible string from exynos-hdmi
ARM: dts: Remove fimd node from exynos5422-odroidxu3-common
ARM: dts: Mark eMMC as non-removable in exynos5250-snow-common
ARM: dts: Remove broken-cd from eMMC node in exynos5420-peach-pi
ARM: dts: Remove broken-cd from eMMC node in exynos5800-peach-pi
ARM: dts: Mark SDIO as non-removable in exynos5250-snow-common
ARM: dts: Mark SDIO as non-removable in exynos5420-peach-pit
ARM: dts: Mark SDIO as non-removable in exynos5800-peach-pi
...
related to dm814x, just the clocks are a bit different and it has a
different set of integrated devices. And let's get some basic dm814x
and dra62x devices working as many of the devices are like on am33xx::
- pinctrl using the pinctrl defines as for am33xx
- Updated EDMA bindings with support for using exma_xbar
- MMC support for dm814x-evm, t410 and dra62x-j5eco-evm
- USB support for dm814x-evm, t410 and dra62x-j5eco-evm
This branch depends on an earlier omap-for-v4.5/81xx-fixes-signed
branch that has dm814x dts fixes interlaced with SoC related fixes to
keep things booting. The interlaced SoC and dts fixes were needed
because of issues with the device tree defined clocks that just
happened to work on bootloader timings for t410 earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W/MF
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/81xx-dts-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "reworked dts changes for ti81xx devices and minimal
dra62x j5ec-evm support" from Tony Lindgren:
Add minimal device tree support for dra62x also known j5eco. It is
related to dm814x, just the clocks are a bit different and it has a
different set of integrated devices. And let's get some basic dm814x
and dra62x devices working as many of the devices are like on am33xx::
- pinctrl using the pinctrl defines as for am33xx
- Updated EDMA bindings with support for using exma_xbar
- MMC support for dm814x-evm, t410 and dra62x-j5eco-evm
- USB support for dm814x-evm, t410 and dra62x-j5eco-evm
This branch depends on an earlier omap-for-v4.5/81xx-fixes-signed
branch that has dm814x dts fixes interlaced with SoC related fixes to
keep things booting. The interlaced SoC and dts fixes were needed
because of issues with the device tree defined clocks that just
happened to work on bootloader timings for t410 earlier.
* tag 'omap-for-v4.5/81xx-dts-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: Add usb support for j5-eco evm
ARM: dts: Add usb support for hp t410
ARM: dts: Add usb support for dm814x-evm
ARM: dts: Add usb support for dm814x and dra62x
ARM: dts: Enable emmc on hp t410
ARM: dts: Add mmc support for dra62x j5-eco evm
ARM: dts: Add mmc support for dm8148-evm
ARM: dts: Add mmc device entries for dm814x
ARM: dts: Update edma bindings on dm814x to use edma_xbar
ARM: dts: Add pinctrl macros for dm814x
ARM: dts: Add minimal dra62x j5-eco evm support
ARM: dts: Add basic support for dra62x j5-eco SoC
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
...
Register the pwm clock for bcm2835.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Some bcm2835 clocks used by hardware (like "PWM" or "H264") can have multiple
parent clocks. These clocks divide the rate of a parent which can be selected by
setting the proper bits in the clock control register.
Previously all these parents where handled by a mux clock. But a mux clock
cannot be used because updating clock control register to select parent needs a
password to be xor'd with the parent index.
This patch get rid of mux clock and make these clocks handle their own parent,
allowing them to select the one to use.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Make bcm2835_clock_choose_div to optionally round up the chosen MASH divisor
so that the resulting average rate will not be higher than the requested one.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Add support for all configurable clocks found on NXP LPC32xx SoC.
The list contains several heterogenous groups of clocks:
* system clocks including multiple dividers and muxes,
* x397 PLL, HCLK PLL and USB PLL,
* peripheral clocks inherited from rtc, hclk and pclk,
* USB controller clocks: AHB slave, I2C, OTG, OHCI and device.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The change adds COMMON_CLK_NXP configuration symbol and enables it for
NXP LPC18XX architecture, this is needed to reuse drivers/clk/nxp
folder for NXP common clock framework drivers other than LPC18XX one.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Clock patches for the Allwinner SoCs:
- H3 clocks
- A10/A20 Video Engine clocks
- DRAM gates
- A80 special CPU clock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Tahe
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Allwinner clocks changes for 4.5
Clock patches for the Allwinner SoCs:
- H3 clocks
- A10/A20 Video Engine clocks
- DRAM gates
- A80 special CPU clock
Use the newly introduced possibility to combine the fractional dividers
with their downstream muxes for all fractional dividers on currently
supported RK3036 SoCs.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Some clocks need to be enabled to accept rate changes. This patch adds a
new flag CLK_SET_RATE_UNGATE that lets clk_change_rate enable the clock
before trying to change the rate and disable it again afterwards.
This of course doesn't effect clocks that are already running at that
point, as their refcount will only temporarily increase.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The clock branches leading to sclk_spdif and sclk_spdif_8ch on RK3288
SoCs only feed those clocks, allow those clocks to change their parents
all the way up the hierarchy.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Use the newly introduced possibility to combine the fractional dividers
with their downstream muxes for all fractional dividers on currently
supported Rockchip SoCs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The fractional dividers of Rockchip SoCs contain an "auto-gating-feature"
that requires the downstream mux to actually point to the fractional
divider and the fractional divider gate to be enabled, for it to really
accept changes to the divider ratio.
The downstream muxes themselfs are not generic enough to include them
directly into the fractional divider, as they have varying sources of
parent clocks including not only clocks related to the fractional
dividers but other clocks as well.
To solve this, allow our clock branches to specify direct child clock-
branches in the new child property, let the fractional divider register
its downstream mux through this and add a clock notifier that temporarily
switches the mux setting when it notices rate changes to the fractional
divider.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
There are a pair of SPI masters and a mini UART that were last minute
additions. As a result, they didn't get integrated in the same way as
the other gates off of the VPU clock in CPRMAN.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
- New boards support: imx51-ts4800, imx6q-novena, CompuLab imx7d SoM/SBC,
vf610m4-cosmic
- Add ADC device support for imx6ul and imx7d
- Remove config space from PCIe controller ranges property for i.MX6
- Add Vivante GPU nodes for i.MX6
- Add DCU, LCD, and SATA devices for LS1021A
- A series to update Ventana gw5xxx boards getting HDMI and LVDS to work
simultaneously and devices like PWM and SPI added
- Quite a few random cleanups and minor updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWeV5EAAoJEFBXWFqHsHzOk8YH/RrzIcDxVa7E6PiVErJmDluH
ihMgY1mQcgXBcBEVKc0F9gKXZVN7W1xHGTHxVZp83mTxEJArBjFhojFQYReUaALU
sQKot0sD8EWBlcC+fvuLzhHc8jE2Udioi/Ys/kgl8T82Q/LXTCnUmBnsPaVshqod
WQ4i4Hk/QV6FbCEgvJvwEMEth53JYLVlAkuVbXi32eo7iv6u6d/LEdCW88bpV8Gv
OxnGg8BiBV3TdAaAcNX72p5IRy9AYMY2hYIx9MCec+H2ws/jzn7xvfkhLta6luTP
4JMvdToQWkhscIEDK1Q/3PtJVmX1al1PWKLTve3tza6jTTc7Opav8XN1hH3nJls=
=hXxT
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree updates for 4.5:
- New boards support: imx51-ts4800, imx6q-novena, CompuLab imx7d SoM/SBC,
vf610m4-cosmic
- Add ADC device support for imx6ul and imx7d
- Remove config space from PCIe controller ranges property for i.MX6
- Add Vivante GPU nodes for i.MX6
- Add DCU, LCD, and SATA devices for LS1021A
- A series to update Ventana gw5xxx boards getting HDMI and LVDS to work
simultaneously and devices like PWM and SPI added
- Quite a few random cleanups and minor updates
* tag 'imx-dt-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (50 commits)
ARM: dts: imx7d: sbc-imx7: add basic board support
ARM: dts: imx7d: cl-som-imx7: add basic module support
ARM: dts: TS-4800: add touchscreen support
ARM: dts: ts-4800: Add LCD support
ARM: dts: imx6q: add Novena board
devicetree: bindings: Add vendor prefix for Kosagi
ARM: dts: TS-4800: use weim IP to map the FPGA
ARM: dts: TS-4800: drop uart rts/cts pin reservations
ARM: dts: imx6: add Vivante GPU nodes
ARM: dts: imx28: add alternate auart4 pinmux
ARM: dts: ls1021a: add sata node to dts
ARM: dts: TS-4800: add basic device tree
of: documentation: add bindings documentation for TS-4800
of: add vendor prefix for Technologic Systems
ARM: dts: imx7d-sdb: add ADC support
ARM: dts: imx7d.dtsi: add ADC support
ARM: dts: vf-colibri: add CAN support
ARM: mxs: dt: cfa10057: fix backlight PWM
ARM: dts: imx6qdl: move GIC to right location in DT
ARM: dts: imx6qdl: add IPU aliases
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the Dove PLL dividers, which are used to generate the
clocks for the AXI bus, as well as the GPU and VMeta peripherals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
drivers/clk/samsung updates (mostly bug fixes):
- instantiation of the cpu clocks and addition of the GSCL
IP parent clocks to the list of available consumer clocks
for exynos542x SoCs;
- MFC IP parent clock fix for exynos542x;
- fix of locking bug in samsung/clk-cpu.c which caused
system crashes with cpufreq enabled;
- minor cleanup for s3c2410.
The i.MX clock updates for 4.5:
- Add is_prepared function callback for pllv3 clock driver
- Use imx_check_clocks() on imx6ul and imx7d clock drivers to save
some code
- Add a core clock for imx7d to support generic cpufreq driver
- Support imx6q clock routing with OSC to anaclk2/2b
- To support more precise pixel clocks on imx5, allow ipu_di_sel clock
selectors to influence the PLLs that they are derived from
- A cleanup on imx25 OSC clock
Rockchip clock changes for 4.5 containing
- a new pll-type used on rk3036 and other Cortex-A7 socs
- new clock-trees for rk3036 and rk3228
- switch rk3288 plls to slow mode on reboot
- a bunch of new clock ids
- some more critical clocks
- wrong register offsets for the rk3368 cpuclks
- allowing more than 2 parents for the cpuclk
This code is unreadable due to the blank line between if and else
blocks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
As commit 1d33929e2a ("clk: rockchip: switch PLLs to slow mode before
reboot for rk3288") states, switching the PLLs to slow-mode is only
necessary when rebooting using the soft-reset done through the CRU.
The dwc2 controllers used create really big number of interrupts in
special constellations involving usb-hubs and their number is so high,
it can even overwhelm the interrupt handler if the cpu-speed os to low.
Right now the PLLs are put into slow-mode in a shutdown syscore_ops
callback which means it happens on all reboots (not only the soft-reset
ones) and even on poweroff actions.
This can result in the system not powering off and getting stuck instead,
so we should move the slow-mode change nearer to the actual reboot action.
For this we introduce the possiblity to also set a callback that gets
called from the restart-handler directly prior to restarting the system
and move the shutdown-callback to this new option.
With this the slow-mode switch is done only on the necessary reboots
and also has a smaller possibility of causing artifacts.
Fixes: 1d33929e2a ("clk: rockchip: switch PLLs to slow mode before reboot for rk3288")
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
The 'fixes' branch contains d5d4fdd86f ("irqchip/versatile-fpga:
Fix PCI IRQ mapping on Versatile PB") that is required for booting
the versatile platform prior to the rework in this branch, but
including both causes a build-time error.
I'm doing an evil merge here to pull in the fixes branch so we have
that commit included but at the same time revert the trivial change.
This gives us a bisectable history.
* fixes: (22 commits)
fsl-ifc: add missing include on ARM64
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
...
This fixes a bug in tegra_clk_register_pllss() which mistakenly assume
the IDDQ register is the PLL base address.
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This fixes two things.
- Read the correct IDDQ register
- Check the correct IDDQ bit position
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Without this change clk_get_rate would return the final output
rather than the VCO output as it would factor in the pdiv when
it shouldn't. This will cause problems for all dividers in the
subtree of the VCO PLL.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Super clock divider control and clock source mux of Tegra210 has changed
a little against prior SoCs, this patch adds Gen5 logic to address those
differences.
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add some logic for Spread Spectrum control. It is used in conjuncture
with SDM fractional dividers. SSC has to be disabled when we configure
the divider settings.
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a callback to the pll_params for custom dynamic ramping
functions which can be specified per PLL.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add logic which (if specified for a pll) can verify that a PLL is set
to the proper default value and if not can set it. This can be
specified per PLL as each will have different default values.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This code makes use of the SDM fractional divider if present to
constrain the allowable programming range of the PLL divider register
bitfields to take advantage of higher frequency granularity that can
be induced by the SDM divider.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 SoC's have 2 PLLs for memory usage. Add plumbing to register
and handle PLLMB.
PLLMB is used to allow switching between 2 PLLM's without having to use
and intermediate backup PLL, as we need to lock the PLL before we can
switch to it.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra210 SoC's, the logic to enable several of the plls is different
from previous generations. Therefore, add registration functions specific
to Tegra210 which will handle them appropriately.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
ACLK_VIO is the noc bus clock for display module, display cann't
read data from ddr without this clock enabled.
Due to it shouldn't belong to any driver, but we need it enabled,
so just mark it as the CLK_IGNORE_UNUSED flag.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Proper source for MFC block is mout_user_aclk333 (in datasheet named
USER_MUX_ACLK_333), not the output of CLKDIV_ACLK_333 MUX.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Fix cpu clock configuration data for Exynos5422/5800 SoCs
(they use higher PCLK_DBG divider values than Exynos5420 and
support additional frequencies).
Based on Hardkernel's kernel for ODROID-XU3 board.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
With the addition of the new Samsung specific cpu-clock type, the
arm clock can be represented as a cpu-clock type. Add the CPU clock
configuration data and instantiate the CPU clock type for Exynos5420.
Changes by Bartlomiej:
- split Exynos5420 support from the original patches
- moved E5420_[EGL,KFC]_DIV0() macros to clk-exynos5420.c
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds clocks, which are required for preserving parent clock
configuration on GSCL power domain on/off.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
multiplatform and extended DT support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Zhx3
-----END PGP SIGNATURE-----
Merge tag 'realview-base-armsoc-1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/multiplatform
Merge "Realview multiplatform support" from Linus Walleij:
The board and infrastructure changes for RealView
multiplatform and extended DT support.
* tag 'realview-base-armsoc-1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: add an DT SMP boot method
ARM: realview: select SP810 and ICST for the DT variant
soc: versatile: add support for the PB11MPCore
clk: versatile-icst: add device tree support
clk: versatile-icst: refactor to allocate regmap separately
clk: versatile-icst: convert to use regmap
ARM: realview: remove private barrier implementation
ARM: no longer force unbuffered DMA for realview
clk/realview: stop using machine headers
ARM: realview: don't map undefined PCI registers
ARM: realview: remove sparsemem hack
Conflicts:
drivers/clk/versatile/Kconfig
Merge "ARM Versatile multi-platform support" from Rob Herring:
Arnd lit a fire under me to dust this off and get it merged. So here it
is. The main change from prior version is I merged all the code to a
single file. It's a bigger patch than I'd like, but I don't think trying
to do it in multiple steps is worth it.
This is dependent on some solution for the default platform choice on
!MMU builds (allnoconfig) as it can't be Versatile after this series.
Arnd has some ideas on how to address that.
This is tested under QEMU. Linus previously tested this on actual h/w
and had a problem with the display identification which needs
investigation or agreement to worry about it if and when someone
actually cares.
* versatile/multiplatform:
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
With DT support for clocks, irqchips, timers, and PCI now in place, DT
based booting has feature parity with non-DT legacy boot. The final
piece is actually enabling common clock support on Versatile. Enabling
full DT support requires either removing the old Versatile clock code,
updating the legacy boot to use the common clock code, or making DT and
legacy boot mutually exclusive. Given that removing legacy boot code is
the goal anyway, I am going with the 1st option.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds support for the ARM syscon ICST clocks to initialized
directly from the device tree syscon node on ARM Integrator,
Versatile and RealView reference designs.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Break out the registration function so it creates a regmap and
pass to the setup function, so the latter can be shared with
a device tree probe function that already has a regmap.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of passing around register bases, pass around a regmap
in this driver. This refactoring make things so much easier when
we later want to manage an ICST that is part of a syscon.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to move realview into multiplatform, we have to prevent device
drivers from accessing the machine header files.
In case of the clk driver, this is very simple, we just copy the
small set of register definitions into the driver that needs them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function can return negative values, so its result should
be assigned to signed variable.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
"index" needs to be signed for the error handling to work.
Fixes: ab6e23a4e3 ('clk: sunxi: Add H3 clocks support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that was
just added in 4.4, or that has been broken for many years without anyone
noticing.
at91/sama5d2
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin
- fix incorrect clock input for SDIO
exynos
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx
- Fix vf610 SAI clock configuration bug which is discovered by
the newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx
- fix prototypes for readl/writel functions
ls2080a
- use little-endian register access for GPIO and SDHCI
omap
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa
- use PWM lookup table for all ezx machines
s3c24xx
- Remove incorrect __init annotation from s3c24xx cpufreq driver structures.
versatile
- fix PCI IRQ mapping on Versatile PB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fgEd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
Reference the newly added efuse clock-ids in the clock-tree.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the clock tree definition for the new rk3228 SoC.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3228's armclk has 3 parents, so allow cpuclk to have
more than 2 parents.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The APBS clock on sun9i is the same as the APB0 clock on sun8i. With
sun9i we are supporting the PRCM clocks by using CLK_OF_DECLARE,
instead of through a PRCM mfd device and subdevices for each clock
and reset control. As such we need a CLK_OF_DECLARE version of
the sun8i-a23-apb0-clk driver.
Also, build it for sun9i/A80, and not just for configurations with
MFD_SUN6I_PRCM enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a new R-Car H3 Clock Pulse Generator / Module Standby and Software
Reset driver, using the new CPG/MSSR driver core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the common core for the new Renesas Clock Pulse Generator / Module
Standby and Software Reset driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Renesas DIV6 clocks provide a single clock output. Hence make the
"clock-output-names" DT property optional instead of mandatory. In case
the DT property is omitted the DT node name will be used.
Rename the variable "name" to "clk_name" to make the code more similar
with fixed-factor-clock.c, and to avoid a conflict with a nested local
variable while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Shmobile is all multiplatform these days, so get rid of the reference to
CONFIG_ARCH_SHMOBILE_MULTI in drivers/clk/shmobile/.
Also instead of always enabling DIV6 and MSTP adjust the Makefile
to enable DIV6 and MSTP depending on if they are included in the
SoC or not.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The video engine has its own special module clock, consisting of a clock
gate, configurable dividers, and a reset control.
On later (sun[68]i) families, the reset control is moved out of this
piece of hardware and grouped with reset controls of other peripherals.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The H3 clock control unit is similar to the those of other sun8i family
members like the A23.
It adds a new bus gates clock similar to the simple gates, but with a
different parent clock for each single gate.
Some of the gates use the new AHB2 clock as parent, whose clock source
is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
is mostly based on Allwinner kernel source code.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10/A20 share the same set of DRAM clock gates, which controls
direct memory access for some peripherals.
On the A10, bit 15 controls the system's DRAM clock output (possibly
to the DRAM chips), which we need to keep on.
On the A20 this has been moved to the DRAM controller, becoming a no-op.
However it is still listed in the user manual, so add it anyway.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
BCM63138 has a simple clocking domain which is primarily the ARMPLL
clocking complex, from which the ARM (CPU), APB and AXI clocks would be
derived from.
Since the ARMPLL controller is entirely compatible with the iProc ARM
PLL, we just initialize it without additional parameters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The timer clock aliases are needed early on dm814x. Let's also
add the aliases for the interconnects and MMC.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Due to a copy-paste error the the rk3368 cpuclk settings were acessing
rk3288-specific register offsets. This never caused problems till now,
as cpu frequency scaling in't used currently at all.
Reported-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Contrary to what the datasheet says, the pre divider doesn't seem to be
incremented by one in the PLL2, but just uses the value from the register,
with 0 being a bypass.
This fixes the audio playing too fast.
Since we now have the same pre-divider flags, and the only difference with
the A10 is the post-divider offset, also remove the structure to just pass
the offset as an argument.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: eb662f8547 ("clk: sunxi: pll2: Add A13 support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently, of_clk_get_parent_name() returns a wrong parent clock name
when "clock-indices" property exists and the target index is not
found in the property. In this case, NULL should be returned.
For example,
oscillator {
compatible = "myclocktype";
#clock-cells = <1>;
clock-indices = <1>, <3>;
clock-output-names = "clka", "clkb";
};
consumer {
compatible = "myclockconsumer";
clocks = <&oscillator 0>, <&oscillator 1>;
};
Currently, of_clk_get_parent_name(consumer_np, 0) returns "clka"
(and of_clk_get_parent_name(consumer_np, 1) also returns "clka",
this is correct). Because the "clock-indices" in the clock parent
does not contain <0>, of_clk_get_parent_name(consumer_np, 0) should
return NULL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add aclk_bus and aclk_peri to the list of rk3368 critical clocks,
which are the base clocks that supply for all peripherals, never
to be disabled automatically.
Signed-off-by: Jianqun xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
To obtain exact pixel clocks, allow the DI clock selectors to influence
the PLLs that they are derived from.
Commit 4591b13289 ("ARM: i.MX6: ipu_di_sel clocks can set parent
rates") did this for i.MX6.
Port it to enable high display resolutions on i.MX53 based platforms
such as CX9020 Embedded PC, too.
Signed-off-by: Patrick Brünn <p.bruenn@beckhoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As we already have a 'imx_check_clocks' to do the clock error
check, so cleanup the error check code.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a virtual arm clk to abstract the actual steps
when changing the ARM core frequency.So we can using
the 'cpufreq-dt' driver on i.MX7D/Solo.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Synchronous Audio Interface (SAI) instances are clocked by
independent clocks: The bus clock and the audio clock (as shown in
Figure 51-1 in the Vybrid Reference Manual). The clock gates in
CCGR0/CCGR1 for SAI0 through SAI3 are bus clock gates, as access
tests to the registers with/without gating those clocks have shown.
The audio clock is gated by the SAIx_EN gates in CCM_CSCDR1,
followed by a clock divider (SAIx_DIV). Currently, the parent of
the bus clock gates has been assigned to SAIx_DIV, which is not
involved in the bus clock path for the SAI instances (see chapter
9.10.12, SAI clocking in the Vybrid Reference Manual).
Fix this by define the parent clock of VF610_CLK_SAIx to be the bus
clock.
If the driver needs the audio clock (when used in master mode), a
fixed device tree is required which assign the audio clock properly
to VF610_CLK_SAIx_DIV.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most rk3368 boards (especially those with Pmic that followed the lead
from rk3368-evb-act8846) have a PWM regulator on them for vdd_logic.
This is the main voltage for all kinds of misc stuff including the
memory controller.
On these boards it is critically important to make sure that the PWM
never ever glitches and never loses its clock. Any glitch could
crash the system.
Right now there are no users of the PWM regulator and also Linux
thinks that the PWM regulator is disabled. Things happen to work
because firmware configured the PWM and Linux doesn't touch it.
..and the PWM's clock is marked as "ignore unused".
...but things _stop_ working if we turn off serial console. Why?
Because:
1. Serial console shares a parent clock with the PWM (pclk_cpu)
2. If we have no serial console then nobody is holding pclk_cpu on
at reboot time. It gets disabled.
We need to fix a lot of the above problems, but until we get
everything right the cleanest "hack" seems like it is to just keep
the "rk_pwm" clock on always.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Lots of header files are never included outside of a mach-pxa
directory and do not need to be made visible in include/mach,
so let's just move them all down one level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The mmp clock drivers currently hardcode the physical addresses for
the clock registers. This is generally a bad idea, and it also gets in
the way of multiplatform builds, which make the platform header files
inaccessible to device drivers.
To work around the header file problem, this patch changes the calling
convention so the three mmp clock drivers get initialized with the base
addresses as arguments from the platform code.
It would still be useful to have a larger rework of the clock drivers,
with DT integration to let the clocks actually be probed automatically,
and the base addresses passed as DT properties. I am unsure if anyone
is still interested in the mmp platform, so it is possible that this
won't happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Chao Xie <chao.xie@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
We've been seeing some crashes at reboot test on rk3288-based systems,
which boards have not reset pin connected to NPOR, they reboot by
setting 0xfdb9 to RK3288_GLB_SRST_FST register. If the APLL works in
a high frequency mode, some IPs might hang during soft reset.
It appears that we can fix the problem by switching to slow mode before
reboot, just like what we did before suspend.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The "cpus" clock is the clock for the embedded processor in the A80.
It is also part of the PRCM clock tree. This clock includes a pre-
divider on one of its inputs. For now we are using a custom clock
driver for it. In the future we may want to develop a generalized
driver for these types of clocks, which also includes the AHB clock
driver on sun[5678]i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds support for the PRCM apbs clock gates found on the
Allwinner A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a driver for the multimedia clock controller found on MSM8996
based devices. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The GPU clocks on msm8996 have three dedicated PLLs, MMPLL2,
MMPLL8, and MMPLL9. We leave MMPLL9 at the maximum speed (624
MHz), and we use MMPLL2 and MMPLL8 for the other frequencies. To
make switching frequencies faster, we ping-pong between MMPLL2
and MMPLL8 when we're switching between frequencies that aren't
the maximum. Implement custom rcg clk ops for this type of
frequency switching.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the global clock controller found on MSM8996
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for configuring rates of, enabling, and disabling
Alpha PLLs. This is sufficient for the types of PLLs found in
the global and multimedia clock controllers.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When we use a clk divider with a divider table, we limit the
maximum divider value in divider_get_val() to the
div_mask(width), but when we calculate the divider in
divider_round_rate() we don't consider that the maximum divider
may be limited by the width. Pass the width along to
_get_table_maxdiv() so that we only return the maximum divider
that is valid. This is useful for clocks that want to share the
same divider table while limiting the available dividers to some
subset of the table depending on the width of the bitfield.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
for_each_available_child_of_node performs an of_node_get on each iteration,
so a break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If get_pll_div() fails we exited by returning NULL but we missed
releasing hwc.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Fixes: 0dfc86b317 ("clk: qoriq: Move chip-specific knowledge into driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The word "cases" is doubled. Keep decent forms for the following
lines.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Errata i810 states that DPLL controller can get stuck while transitioning
to a power saving state, while its M/N ratio is being re-programmed.
As a workaround, before re-programming the M/N ratio, SW has to ensure
the DPLL cannot start an idle state transition. SW can disable DPLL
idling by setting the DPLL AUTO_DPLL_MODE=0 or keeping a clock request
active by setting a dependent clock domain in SW_WKUP.
This errata impacts OMAP5 and DRA7 chips, so enable the errata for these.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
sclk_mipidsi_24m is the gating of mipi dsi phy.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The common clk implementation for MMP broke without anyone noticing
when we stopped including linux/clk.h from the clk-provider header.
This did not show up in the defconfig builds because those use the
legacy MMP clk drivers, and it did not show up in my randconfig tests
either because I was testing with my mmp multiplatform series
applied, which at some point gained the fixup.
This fixes the three broken files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 61ae76563e ("clk: Remove clk.h from clk-provider.h")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add 'is_prepared' callback function for pllv3 type clk to make sure when
the system is bootup, the unused clk is in a known state to match the
prepare count info.
Signed-off-by: Bai Ping <b51503@freescale.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'osc' clock is already initialized by the fixed clock defined in
imx25.dtsi. The imx25 clock driver tries to add this clock for a second
time and fails with -EEXIST:
i.MX clk 1: register failed with -17
As the clock is already properly setup in DT with a different driver, we
can completely remove the handling in the imx25 clock driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TI's mux and divider clock drivers do not require locking and they do
not initialize internal spinlocks. This code was occasionally
copy-posted from generic mux/divider drivers. So remove it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add missing clkdev dmtimer related entries for dm816x.
32Khz and ext sources were missing.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the clock tree definition for the new rk3036 SoC.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3036's pll and clock are different with base on the rk3066(rk3188,
rk3288, rk3368 use it), there are different adjust foctors and control
registers, so these should be independent and separate from the series
of rk3066s.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Set the newly added id for the crypto clk, so that it can be called
in other parts.
Signed-off-by: Zain Wang <zain.wang@rock-chips.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Move the xo and sleep clocks to device-tree, instead of hard-coding
them in the driver. This allows us to insert the RPM clocks (if they
are enabled) in between the on-board oscillators and the actual clock.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clk_hw_omap_ops structures are never modified, so declare this one as
const, like the others.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
BCM63138 has a simple clocking domain which is primarily the ARMPLL
clocking complex, from which the ARM (CPU), APB and AXI clocks would be
derived from.
Since the ARMPLL controller is entirely compatible with the iProc ARM
PLL, we just initialize it without additional parameters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
All these clock controllers are little endian devices, but so far
we've been relying on the regmap mmio bus handling this for us
without explicitly stating that fact. After commit 4a98da2164cf
(regmap-mmio: Use native endianness for read/write, 2015-10-29),
the regmap mmio bus will read/write with the __raw_*() IO
accessors, instead of using the readl/writel() APIs that do
proper byte swapping for little endian devices.
So if we're running on a big endian processor and haven't
specified the endianness explicitly in the regmap config or in
DT, we're going to switch from doing little endian byte swapping
to big endian accesses without byte swapping, leading to some
confusing results. On my apq8074 dragonboard, this causes the
device to fail to boot as we access the clock controller with
big endian IO accesses even though the device is little endian.
Specify the endianness explicitly so that the regmap core
properly byte swaps the accesses for us.
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
quadfs_pll_fs660c32_round_rate prints a few structure members
that are never initialized, and also doesn't print the only one
it cares about. We get a gcc warning about the ones that
are printed:
clk/st/clkgen-fsyn.c:560:93: warning: 'params.sdiv' may be used uninitialized in this function
clk/st/clkgen-fsyn.c:560:93: warning: 'params.mdiv' may be used uninitialized in this function
clk/st/clkgen-fsyn.c:560:93: warning: 'params.pe' may be used uninitialized in this function
clk/st/clkgen-fsyn.c:560:93: warning: 'params.nsdiv' may be used uninitialized in this function
This changes the code to no longer print uninitialized data, and
for good measure it also prints the ndiv member that is being
set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5f7aa9071e ("clk: st: Support for QUADFS inside ClockGenB/C/D/E/F")
Acked-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Commit dca1a4b5ff ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Now that the slow clock is taken properly by the drivers, this workaround
is not necessary anymore, revert it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The X-Gene clock driver missed the divider shift operation when
set the divider value.
Signed-off-by: Loc Ho <lho@apm.com>
Fixes: 308964caee ("clk: Add APM X-Gene SoC clock driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This is according to figure 12 ("I2C Programming Procedure") in
"Si5351A/B/C Data Sheet"
(https://www.silabs.com/Support%20Documents/TechnicalDocs/Si5351-B.pdf).
Without the PLL soft reset, we were unable to get three outputs
working at the same time.
According to Silicon Labs support, performing PLL soft reset will only
be noticeable if the PLL parameters have been changed.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Signed-off-by: Jens Rudberg <jens@teenage.engineering>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This minor refactoring does not change the function behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This if-block can be dropped because the of_parse_phandle_with_args()
in the following line returns -EINVAL for negative index.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If kzalloc fails we will already have many messages in the log and we do
not need another message to know that kzalloc for sp810 has failed.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PLLM is fixed for Tegra30 up through Tegra114. Starting with Tegra124
PLLM can change rate. Mark PLLM as TEGRA_PLL_FIXED for the generations
where it should be. Modify the check in clk_pll_round_rate() and
clk_pll_recalc_rate() to allow for the non-fixed version to return the
correct rate.
Note that there is no change for Tegra20. This is because PLLM is not
distinguished in that driver, and adding either the PLLM or FIXED_RATE
flags will cause potential problems.
PLLM never supported dynamic ramping. On Tegra20 and Tegra30, there is
no dynamic ramping at all, and on Tegra114, Tegra124 and Tegra132, only
PLLX and PLLC support dynamic ramping, so we can go ahead and remove the
specialized pllm_ops.
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This removes the conversion from pdiv to hw, which is already taken
care of by _get_table_rate before this code is run. This avoids
incorrectly converting pdiv to hw twice and getting the wrong hw value.
Also set the input_rate in the freq cfg in _calc_dynamic_ramp_rate while
setting all the other fields.
In order to prevent regressions on earlier SoC generations, all of the
frequency tables need to be updated so that they contain the actual
divider values. If they contain hardware values these would be converted
to hardware values again, yielding the wrong value.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[treding@nvidia.com: fix regressions on earlier SoC generations]
Signed-off-by: Thierry Reding <treding@nvidia.com>
If a PLL has a reset_reg specified, properly handle that in the
enable/disable logic paths.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For Tegra210, the logic to calculate out-of-table rates is different
from previous generations. Add callbacks that can be overridden to
allow for different ways of calculating rates. Default to
_cal_rate when not specified.
This patch also includes a new flag which is used to set which method
of fixed_mdiv calculation is used. The new method for calculating the
fixed divider value for M can be more accurate especially when
fractional dividers are in play. This allows for older chipsets to use
the existing logic and new generations to use a newer version which
may work better for them.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds logic for taking SDM_DIN (Sigma Delta Modulator) setting into
the equation to calculate the effective N value for PLL which supports
fractional divider.
The effective N = NDIV + 1/2 + SDM_DIN/2^13, where NDIV is the integer
feedback divider.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
SoC specific drivers should define the appropriate flags for each
PLL rather than relying on the registration functions to automatically
set flags on their behalf. This will properly allow for changes between
SoC generations where flags might be different and allow sharing the
same logic functions.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
New SoC's may have more than 3 MISC registers, so bump up the array size
and use a #define to be more informative about the value.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Swap out the generic WARN_ON with a WARN which gives more information
about what is happening.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of having multiple similar wrapper functions for
_clk_pll_[enable|disable], we can simplify it to single
wrappers and use checks to avoid the logic we don't want to use.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Create a wrapper interface to make use of the existing
clk_pll_wait_for_lock. This will be useful for implementations
of callbacks in Tegra SoC specific clock drivers.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has significant differences in muxes for peripheral clocks.
One of the most important changes is that pll_m isn't to be used
as a source for peripherals. Therefore, we need to define the new
muxes and new clocks to use those muxes for Tegra210 support.
Tegra210 has some differences in the PLLP clock tree:
- Four new output clocks: PLLP_OUT_CPU, PLLP_OUT_ADSP, PLLP_OUT_HSIO,
and PLLP_OUT_XUSB.
- PLLP_OUT2 is fixed at 1/2 the rate of PLLP_VCO.
- PLLP_OUT4 is the child of PLLP_OUT_CPU.
Update the xusb_hs_src mux and add the xusb_ssp_src mux for Tegra210.
Including work by Andrew Bresticker <abrestic@chromium.org> and
Bill Huang <bilhuang@nvidia.com>.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The H3 has a usb-phy clk register which is similar to that of earlier
SoCs, but with support for a larger number of phys. So we can simply add
a new set of clk-data and a new compatible and be done with it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Get parent clk names in of_gpio_clk_setup() and store the names
in struct clk_gpio_delayed_register_data instead of doing it from
the clk provider's get() callback. of_clk_get_parent_name() can't
be called in struct of_clk_provider's get() callback since it may
make a call to of_clk_get_from_provider() and this in turn tries
to recursively lock of_clk_mutex.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Cc: Sergej Sawazki <ce3a@gmx.de>
Fixes: 0a4807c2f9 ("clk: Make of_clk_get_parent_name() robust with #clock-cells = 1")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If of_clk_parent_fill() fails then we printed an error message and
returned. But we missed freeing sp810.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use unsigned int for loop variables that can never become negative and
remove a couple of gratuitous blank lines. Also use single spaces around
operators and use a single space instead of a tab to separate comments
from code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The OSC_FREQ field of the OSC_CTRL register uses the value 12 for an
oscillator frequency of 26 MHz, not 260 MHz. This isn't really critical
because I don't think boards with such an oscillator have ever existed,
much less been supported upstream.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a gate clock for controlling all clocks of Security Sub System
(SSS).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Provide support for Sigma Designs Tango4 clock generator.
NOTE: This driver is incompatible with Tango3 clkgen.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[sboyd@codeaurora.org: Add kernel.h include for panic/sprintf]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Put these clocks into the dt files instead of registering them
from C code. This provides a few benefits. It allows us to
specify the frequency of these clocks at the board level instead
of hard-coding them in the driver. It allows us to insert an RPM
clock in between the consumers of the crystals and the actual
clock. And finally, it helps us transition the GCC driver to use
RPM clocks when that configuration is enabled.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We want to put the XO board clocks into the dt files, but we also
need to be backwards compatible with an older dtb. Add an API to
the common code to do this. This also makes a place for us to
handle the case when the RPM clock driver is enabled and we don't
want to register the fixed factor clock.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
New and/or improved SoC support for this release:
- Marvell Berlin:
* Enable standard DT-based cpufreq
* Add CPU hotplug support
- Freescale:
* Ethernet init for i.MX7D
* Suspend/resume support for i.MX6UL
- Allwinner:
* Support for R8 chipset (used on NTC's $9 C.H.I.P board)
- Mediatek:
* SMP support for some platforms
- Uniphier:
* L2 support
* Cleaned up SMP support, etc.
+ A handful of other patches around above functionality, and a few other
smaller changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWQCmaAAoJEIwa5zzehBx3F/0QAKIYmvmJM3sUanNEEwhRilx+
3xhSgld7e25suLGwrNapTkd8VzVB4b8GnJhNShNk+l5WqfqICHCB4Aru2NmJHY8V
yPj5vBrgJTVMnIiH7CRDPz9IlwAkWM4MmWi4PgFuhrk1T/0wPKPNMc40OWOloTeD
gA5YmbbX1hNOqKoI/z+DK7CEdp1lHrEjeYIbnQ0SldFzkY9NKhrI784gtcz3si6E
19pFQ9LA7EtEv7aRcFOA0sazeooa2wiJ9P9L31Mn5APZBJj5H8HjyKdvOmJ8neQn
+b77Tya11Q70U57uDq69l0rl58fpy650uTwYaLNGWmUdTgOiGMWN05lvIVNrQd/R
gP+VEQDGsTH6kqOCy9gyLCmn9q9I7l0t9lwcu5TP52Xy9vqVq9rb388MkcPcsWk8
cYPvD8RcSaywZUV3YJgbYozBfVuf5rLVus6D54pMXe3N12KGaNBt8kk4co4jBwvh
b//1urA82cdlEAZ/kiqHXjRMq/ht+dxtb6sSVOJ9frxPLuc7g1z4ORC+Z0PTS5WC
zB0hMzPnTwXeqHcYpV4wP/vGtgZGpLevBkK7pKVdqKZykV8BS4FiT4HFp6Rghxs3
dxAz7JjQUle6KOX7YfuHdpLnyZFWQvLYyTn946xGKpw2QH/iWLwECpet2I87QzVs
QkEkGygPhK4QcGccxz9N
=h5xk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New and/or improved SoC support for this release:
Marvell Berlin:
- Enable standard DT-based cpufreq
- Add CPU hotplug support
Freescale:
- Ethernet init for i.MX7D
- Suspend/resume support for i.MX6UL
Allwinner:
- Support for R8 chipset (used on NTC's $9 C.H.I.P board)
Mediatek:
- SMP support for some platforms
Uniphier:
- L2 support
- Cleaned up SMP support, etc.
plus a handful of other patches around above functionality, and a few
other smaller changes"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
ARM: uniphier: rework SMP operations to use trampoline code
ARM: uniphier: add outer cache support
Documentation: EXYNOS: Update bootloader interface on exynos542x
ARM: mvebu: add broken-idle option
ARM: orion5x: use mac_pton() helper
ARM: at91: pm: at91_pm_suspend_in_sram() must be 8-byte aligned
ARM: sunxi: Add R8 support
ARM: digicolor: select pinctrl/gpio driver
arm: berlin: add CPU hotplug support
arm: berlin: use non-self-cleared reset register to reset cpu
ARM: mediatek: add smp bringup code
ARM: mediatek: enable gpt6 on boot up to make arch timer working
soc: mediatek: Fix random hang up issue while kernel init
soc: ti: qmss: make acc queue support optional in the driver
soc: ti: add firmware file name as part of the driver
Documentation: dt: soc: Add description for knav qmss driver
ARM: S3C64XX: Use PWM lookup table for mach-smartq
ARM: S3C64XX: Use PWM lookup table for mach-hmt
ARM: S3C64XX: Use PWM lookup table for mach-crag6410
ARM: S3C64XX: Use PWM lookup table for smdk6410
...
Merging in the few patches I had kept separate from main next/dt, since others
got merged here directly.
* next/arm64:
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
arm64: dts: mt8173: Add clocks for SCPSYS unit
arm64: dts: mt8173: Add subsystem clock controller device nodes
+ Linux 4.3-rc5
