Modify the Kconfig so that Freescale QUICC Engine (QE) support is a selectable
option, thereby allowing users to compile kernels without any QE support.
The drawback is that QE support is now disabled by default on platforms that
have a QE, and so a defconfig is needed to enable QE and QE devices (like
UCC GETH). Fortunately, all the current relevant defconfigs do that already.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With arch/ppc gone and all in kernel users of CONFIG_PPC_CPM_NEW_BINDING
fixed up we dont have need for the Kconfig option anymore.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Choosing PCI or not at config time is allowed on some
platforms via an if expression in arch/powerpc/Kconfig.
To add a new platform with PCI support selectable at
config time, you must change the if expression. This
patch makes this easier by changing:
bool "PCI support" if <long expression>
to
bool "PCI support" if PPC_PCI_CHOICE
and adding select PPC_PCI_CHOICE to all the config nodes that
were previously in the PCI if expression.
Platforms with unconditional PCI support continue to
just select PCI in their config nodes.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC85xx MDS board requires some board level tweaks of the PHYs that
either the eTSEC (gianfar) or UCC ethernet controllers are connected to.
Its possible to build the phylib as a module, however this breaks the
board level fix ups because phy_read and phy_write are not available
if we build as a module.
So we unconditionally select PHYLIB to ensure its built into the kernel
if we are building in MPC85xx MDS support. This was determined to be
the easiest soultion even though it prevents the user from removing
PHYLIB support if they decide they don't want it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The kconfig entry can go away once arch/ppc and references to the config in
drivers are removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The KSI8560 is a single compact, mid-, or full-size Advanced Mezzanine Card
(AdvancedMC™) based on the Freescale™ Semiconductor MPC8560 PowerQUICC III™
microprocessor. This product will serve in data and signaling applications such
as signaling gateways (SGW) and softswitch signaling interface cards.
The board has altera maxii CPLD, that is used to obtain and manage board
configuration. Also there are two SCC UART serial consoles and FCC ethernet,
that is routed to the front panel, while other ethernet controlers (TSEC's) are
routed to the backplane.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Allow multiple boards to be selected in a single build
* Removed Kconfig option '85xx' which existed only for compat with arch/ppc
* Added a multiplatform 85xx defconfig (mpc85xx_defconfig). This builds
all 85xx boards except sbc8560 and stx_gp3 since these to boards have
board specific ifdef in driver code that may break all other boards
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds the basic support for the Wind River SBC8548 board, implemented
as powerpc. It closely follows the implementation of the MPC8548CDS.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently there is no way to disable the CPM2 support. Some boards,
like the SBC8560 have their own external UART and don't have any direct
dependencies on the CPM for a serial console or anything else.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds support for the Wind River SBC8560 board, implemented as
powerpc. It closely follows the implementation of the MPC8560ADS.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Renamed the mpc8544_ds.c board code to mpc85xx_ds.c to make it more
generic in prep for other boards based on the same platform.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupt routing in the device trees for the ULI M1575 was
inproperly using the interrupt line field as pci function. Fixed
up the device tree's to actual conform for to specification and
changed the interrupt mapping code so it just uses a static mapping
setup as follows:
PIRQA - IRQ9
PIRQB - IRQ10
PIRQC - IRQ11
PIRQD - IRQ12
USB 1.1 OCHI (1c.0) - IRQ12
USB 1.1 OCHI (1c.1) - IRQ9
USB 1.1 OCHI (1c.2) - IRQ10
USB 1.1 ECHI (1c.3) - IRQ11
LAN (1b.0) - IRQ6
AC97 (1d.0) - IRQ6
Modem (1d.1) - IRQ6
HD Audio (1d.2) - IRQ6
SATA (1f.1) - IRQ5
SMB (1e.1) - IRQ7
PMU (1e.2) - IRQ7
PATA (1f.0) - IRQ14/15
Took the oppurtunity to refactor the code into a single file so we
don't have to duplicate these fixes on the two current boards in the
tree and several forth coming boards that will also need the code.
Fixed RTC support that requires a dummy memory read on the P2P bridge
to unlock the RTC and setup the default of the RTC alarm registers to
match with a basic x86 style CMOS RTC.
Moved code that poked ISA registers to a FIXUP_FINAL quirk to ensure
the PCI IO space has been setup properly before we start poking ISA
registers at random locations.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale MPC8555CDS and MPC8548CDS reference hardware has a legacy
8259 interrupt controller pair contained within a VIA VT82C686B Southbridge
on the main carrier board. The processor complex plugs into the carrier
card using a PCI slot which limits the available interrupts to the
INTA-INTD PCI interrupts. The output of the 8259 cascade pair is routed
through a gate array and connected to the PCI INTA interrupt line.
The normal interrupt chaining hook (set_irq_chained_handler) does
not allow sharing of the chained interrupt which prevents the
use of PCI INTA by PCI devices. This patch allows the 8259 cascade
pair to share their interrupt line with PCI devices.
NOTE: The addition of the .end routine for the MPIC is not strictly
necessary for this patch. It's there so this code will run from within
the threaded interrupt context used by the Real Time patch.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian. This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch the 85xx platform over to using the FSL generic PCI code. This
gets ups PCIe support in addition to base PCI support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch provides the basic MPC8544 DS platform code and config.
Follow-up patches will add peripherals such as PCI and SATA.
Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Renamed the MPC8568 MDS platform code to follow other 85xx boards. There
isn't anything specific about the 8568 MDS code that wouldn't apply to another
85xx MDS system at this point.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8568 MDS reference board
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This makes the 8560 evaluation board fully supported under arch/powerpc,
as the first board with CPM2 SoC peripherals. The brand new devicetree
nodes are introduced (intending to be a subset of the QuiccEngine-equipped
models, with dts sources placed into the kernel according to the new convention.
Assuming all the preceding stuff applied (PAL+fs_enet related+ CPM_UART
update), the both TSEC eth ,FCC Eths, and both SCC UARTs are
working. The relevant drivers are still capable to drive users in ppc,
which was verified with 8272ADS (SCC uart+FCC eth).
This is also verified on mpc8540 and actually make it work (PCI stuff
working as well)
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
* Fix IRQ support in the 85xx CDS boards so it uses the new
generic stuff
* Fix PCI IRQ mapping to use the device tree
* Disabled i8259 support to allow the CDS to boot. This will be
fixed soon, but the current code doesn't even compile, so this
is a vast improvement
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for 85xx CDS support to arch/powerpc
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we build for the MPC8540 ADS produce a uImage by default.
Updated the defconfig to reflect this as well.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated patch for support for mpc8540_ads in arch/powerpc with a
flat OF device tree. This patch does not yet support PCI or I2C.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
