This patch adds support for the GPIO functions of PPC40x and PPC44x
SOCs.
Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR FLASH,
UART, EEPROM and temperature sensor, along with a shared debug port.
The two 460GT's will communicate with each other via shared memory,
Gigabit Ethernet and x1 PCI-Express.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the Yosemite board to the explicitly supported list for ppc44x_simple
boards and remove the compatible entry for bamboo from the DTS file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add explicit support for the AMCC Glacier eval board to Kconfig and the
ppc44x_simple file. Also removes the cayonlands compatible entry from the
DTS file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a common board file for almost all of the "simple" PowerPC 44x
boards that exist today. This is intended to be a single place to add
support for boards that do not differ in platform support from most of the
evaluation boards that are used as reference platforms. Boards that have
specific requirements or custom hardware setup should still have their own
board.c file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch removes the i2c code which is now obsolete due to the new
ibm iic driver walking the device tree for child nodes.
There are two other small cleanups that came indirectly from the ad7414
code review. Make sure Tlow is correct and handle the case where
i2c_smbus_read_word_data fails.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Allow the Rev A Warp boards to boot from NAND.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Support for the Xilinx Virtex5 FXT 440 is being added.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Sam440ep is an high customizable general purpose mini-itx board,
based on the AMCC 440EP and with a LatticeXP FPGA onboard.
It's poduced by ACube Systems Srl (Bassano del Grappa, Italy),
http://www.acube-systems.biz.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The "ndfc-chip" device doesn't need any resources. All resources
are handled by the "ndfc-nand" device. Registering the same memory
resource twice causes "cat /proc/iomem" to go into an infinite loop
displaying NDFC memory addresses.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* Switched from 64M NOR/64M NAND to 4M NOR/256M NAND.
* Full DTM support including critical temperature.
* Added POST information.
* Removed LED function, moved to new LED driver.
* Moved ad7414 to new style I2C initialization.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This changes the cpu_idle loop for 44x platforms to utilize the Wait Enable
feature of the CPU. This helps virtulization solutions know when the guest
Linux kernel is in an idle state.
A command line option called "idle" is also added to allow people to change
the idle loop back to the original variation. This is done by setting
"idle=spin" on the kernel command line.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
With a multiplatform kernel, once built we always have warp_setup_nand_flash()
called and NDFC probed, no matter what machine we actually run on. This
potentially can cause problems (such as kernel crash), since NDFC is probed at
a warp-predefined address.
Using machine_device_initcall() NAND devices are registered if we run on a warp only.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch creates a common system reset routine for all 40x and 44x
systems. Previously only a 44x routine existed. But since this system
reset via the debug control register is common for 40x and 44x let's
share this code for all those platforms in ppc4xx_soc.c.
This patch also enables CONFIG_4xx_SOC for all 40x and 44x platforms.
Tested on Kilauea (405EX) and Canyonlands (440EX).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds support for the 256k L2 cache found on some IBM/AMCC
4xx PPC's. It introduces a common 4xx SoC file (sysdev/ppc4xx_soc.c)
which currently "only" adds the L2 cache init code. Other common 4xx
stuff can be added later here.
The L2 cache handling code is a copy of Eugene's code in arch/ppc
with small modifications.
Tested on AMCC Taishan 440GX.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The AMCC 440EP Yosemite board is very similar to the original AMCC Bamboo
board. This adds a YOSEMITE option to Kconfig, and reuses the existing
bamboo board support in the kernel.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Canyonlands is the AMCC 460EX eval board, featuring nearly all of the 460EX
interfaces:
- 1 * PCI (max 66MHz), 2 * PCIe (one 4-lane, one 1-lane)
- 2 * GBit Ethernet with TCP/IP acceleration
- USB 2.0 Host/Device OTG and Host interface
- SATA port
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
While merging, I found a small bug that I forgot to send. I add an
offset to a value twice.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the base platform support for the PIKA Warp boards.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch extends the Ebony and Walnut platform code to instantiate
the existing ds1742 RTC class driver for the DS1743 RTC/NVRAM chip
found on both those boards. The patch uses a helper function to scan
the device tree and instantiate the appropriate platform_device based
on it, so it should be easy to extend for other boards which have mmio
mapped RTC chips.
Along with this, the device tree binding for the ds1743 chips is
tweaked, based on the existing DS1385 OF binding found at:
http://playground.sun.com/1275/proposals/Closed/Remanded/Accepted/346-it.txt
Although that document covers the NVRAM portion of the chip, whereas
here we're interested in the RTC portion, so it's not entirely clear
if that's a good model.
This implements only RTC class driver support - that is /dev/rtc0, not
/dev/rtc, and the low-level get/set time callbacks remain
unimplemented. That means in order to get at the clock you will
either need a modified version of hwclock which will look at
/dev/rtc0, or you'll need to configure udev to symlink rtc0 to rtc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Some machine_xx_initcall macros were recently added that check for the machine
type before calling the function. This converts the 4xx platforms to use those
for bus probing.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Enable PCI support for these eval boards among other things. Also selects
PCI for Rainier in the Kconfig file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
A small error caused a header file to be removed making sequoia support no
longer compile. Fix it.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This makes 4xx embedded platforms re-assign all PCI resources as we
pretty much never care about what the various firmwares have done on
these, it's generally not compatible with the way the kernel will map
the bridges.
We still need to also enable bus renumbering on some of them, but I
will do that from a separate patch after I've fixed 4xx PCIe to handle
all bus numbers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds base support for the Katmai board, including PCI-X and
PCI-Express (but no RTC, nvram, etc... yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds the device-tree bits & call to ppc4xx_pci_find_bridges()
to make PCI work on the Bamboo board
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds base support for the AMCC Taishan 440GX evaluation
board.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This wires up the 4xx PCI support & device tree bits for
440GP based Ebony platform.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a cputable function pointer for the CPU-side machine
check handling. The semantic is still the same as the old one,
the one in ppc_md. overrides the one in cputable, though
ultimately we'll want to change that so the CPU gets first.
This removes CONFIG_440A which was a problem for multiplatform
kernels and instead fixes up the IVOR at runtime from a setup_cpu
function. The "A" version of the machine check also tweaks the
regs->trap value to differenciate the 2 versions at the C level.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Fix some device tree omissions that prevented the new EMAC driver from
setting up ethernet on the Bamboo board correctly and update the Bamboo
defconfig.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch enables NEW EMAC support for PowerPC 440EPx Sequoia board.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds RGMII support to Sequoia DTS and sets correct phy-mode
for EMACs. According to Sequoia datasheet, both ethernet ports
are connected to RGMII interface, while ZMII is used only for MDIO.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs. The
same ASIC is also found in the Axon bridge chip. This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging. Specifically:
- Should be adjusted to properly use the dma mapping API.
Axon needs this.
- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices. The dependencies here between
EMAC, MAL, ZMII etc. make this complicated. At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit 804ace8881 changed the behavior of how compatible nodes are found.
This highlighted a bug on the Bamboo board where it wasn't probing the bus
specified in the DTS file. We fix it by being explicit about which bus to
probe.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbvear.id.au>
