Again, the cleaned up code introduced some resource warnings:
drivers/pci/setup-bus.c: In function 'pci_bus_dump_res':
drivers/pci/setup-bus.c:542: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'resource_size_t'
drivers/pci/setup-bus.c:542: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'resource_size_t'
Fix those up too.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The cleaned up resource code in probe.c introduced some warnings:
drivers/pci/probe.c: In function 'pci_read_bridge_bases':
drivers/pci/probe.c:386: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'resource_size_t'
drivers/pci/probe.c:386: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/pci/probe.c:398: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'resource_size_t'
drivers/pci/probe.c:398: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/pci/probe.c:434: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/pci/probe.c:434: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'resource_size_t'
So fix them up.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some BIOSes (the Intel DG33BU, for example) wrongly claim to have DMAR
when they don't. Avoid the resulting crashes when it doesn't work as
expected.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When disconnected ccw devices are removed, the device has to be set
offline, otherwise there will be side effects including a reference
count imbalance. This patch modifies ccw_device_offline to work for
devices in disconnecte/not operational state. ccw_device_offline is
called by cio for devices which are online during device removal.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ssch() has two classes of return codes:
- condition codes (0-3) which need to be translated to Linux
error codes
- Linux error codes (-EIO on exceptions) which should be passed
to the caller (instead of erronously being handled like
condition code 3)
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix cleanup on error in chp_new() and init_channel_subsystem()
(must not call kfree() on structures that had been registered).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
pata_sil680: remove duplicate pcim_enable_device
libata-sff: kill spurious WARN_ON() in ata_hsm_move()
sata_nv: disable hardreset for generic
ahci: disable PMP for marvell ahcis
sata_mv: add RocketRaid 1720 PCI ID to driver
ahci, pata_marvell: play nicely together
The hw interface drivers for the usb serial devices deference the tty
structure to set up the parameters for the initial console. The tty
structure should be passed as a parameter to the set_termios() call.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set the class so it doesn't clash with the normal memory class.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
===================================================================
Remove duplicate call to pcim_enable_device in sil680_init_one.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On HSM_ST_ERR, ata_hsm_move() triggers WARN_ON() if AC_ERR_DEV or
AC_ERR_HSM is not set. PHY events may trigger HSM_ST_ERR with other
error codes and, with or without it, there just isn't much reason to
do WARN_ON() on it. Even if error code is not set there, core EH
logic won't have any problem dealing with the error condition.
OSDL bz#11065 reports this problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
of them being unifying probing, hotplug and EH reset paths uniform.
Previously, broken hardreset could go unnoticed as it wasn't used
during probing but when something goes wrong or after hotplug the
problem will surface and bite hard.
OSDL bug 11195 reports that sata_nv generic flavor falls into this
category. Hardreset itself succeeds but PHY stays offline after
hardreset. I tried longer debounce timing but the result was the
same.
http://bugzilla.kernel.org/show_bug.cgi?id=11195
So, it seems we'll have to drop hardreset from the generic flavor.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Marvell ahcis don't play nicely with PMPs. Disable it.
Reported by KueiHuan Chen in the following thread.
http://thread.gmane.org/gmane.linux.ide/33296
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: KueiHuan Chen <kueihuan.chen@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I've been chasing Jeff about this for months. Jeff added the Marvell
device identifiers to the ahci driver without making the AHCI driver
handle the PATA port. This means a lot of users can't use current
kernels and in most distro cases can't even install.
This has been going on since March 2008 for the 6121 Marvell, and late 2007
for the 6145!!!
This was all pointed out at the time and repeatedly ignored. Bugs assigned
to Jeff about this are ignored also.
To quote Jeff in email
> "Just switch the order of 'ahci' and 'pata_marvell' in
> /etc/modprobe.conf, then use Fedora's tools regenerate the initrd.
> See? It's not rocket science, and the current configuration can be
> easily made to work for Fedora users."
(Which isn't trivial, isn't end user, shouldn't be needed, and as it usually
breaks at install time is in fact impossible)
To quote Jeff in August 2007
> " mv-ahci-pata
> Marvell 6121/6141 PATA support. Needs fixing in the 'PATA controller
> command' area before it is usable, and can go upstream."
Only he add the ids anyway later and caused regressions, adding a further
id in March causing more regresions.
The actual fix for the moment is very simple. If the user has included
the pata_marvell driver let it drive the ports. If they've only selected
for SATA support give them the AHCI driver which will run the port a fraction
faster. Allow the user to control this decision via ahci.marvell_enable as
a module parameter so that distributions can ship 'it works' defaults and
smarter users (or config tools) can then flip it over it desired.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The current check for monotonicity is way too weak: Andreas Mohr reports (
http://lkml.org/lkml/2008/8/10/77 ) that on one of his test systems the
current check only triggers in 50% of all cases, leading to catastrophic
timer behaviour. To fix this issue, expand the check for monotonicity by
doing ten consecutive tests instead of one.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On all hardware (some Intel ICH4, PIIX4 and PIIX4E chipsets) affected by a
hardware errata there's about a 4.2% chance that initialization of the
ACPI PMTMR fails. On those chipsets, we need to read out the timer value
at least three times to get a correct result, for every once in a while
(i.e. within a 3 ns window every 69.8 ns) the read returns a bogus
result. During normal operation we work around this issue, but during
initialization reading a bogus value may lead to -EINVAL even though the
hardware is usable.
Thanks to Andreas Mohr for spotting this issue.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
mmc_block_open() increments md->usage although it returns with -EROFS when
default mounting a MMC/SD card with write protect switch on. This
reference counting bug prevents /dev/mmcblkX from being released on card
removal, and situation worsen with reinsertion until the minor number
range runs out.
Reported-by: <sasin@solomon-systech.com>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix regression tracked as http://bugzilla.kernel.org/show_bug.cgi?id=11361
and caused by commit f735a2a1a4 ("[netdrvr]
forcedeth: setup wake-on-lan before shutting down") that makes network
adapters integrated into the NVidia MCP55 chipsets fail to work in kexeced
kernels. The problem appears to be that if the adapter is put into D3_hot
during ->shutdown(), it cannot be brought back into D0 after kexec (ref.
http://marc.info/?l=linux-kernel&m=121900062814967&w=4). Therefore, only
put forcedeth into D3 during ->shutdown() if the system is to be powered
off.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/~dwmw2/dwmw2-2.6.27:
Revert "[ARM] use the new byteorder headers"
Fix conditional export of kvh.h and a.out.h to userspace.
[MTD] [NAND] tmio_nand: fix base address programming
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (98 commits)
V4L/DVB (8881): gspca: After 'while (retry--) {...}', retry will be -1 but not 0.
V4L/DVB (8880): PATCH: Fix parents on some webcam drivers
V4L/DVB (8877): b2c2 and bt8xx: udelay to mdelay
V4L/DVB (8876): budget: udelay changed to mdelay
V4L/DVB (8874): gspca: Adjust hstart for sn9c103/ov7630 and update usb-id's.
V4L/DVB (8873): gspca: Bad image offset with rev012a of spca561 and adjust exposure.
V4L/DVB (8872): gspca: Bad image format and offset with rev072a of spca561.
V4L/DVB (8870): gspca: Fix dark room problem with sonixb.
V4L/DVB (8869): gspca: Move the Sonix webcams with TAS5110C1B from sn9c102 to gspca.
V4L/DVB (8868): gspca: Support for vga modes with sif sensors in sonixb.
V4L/DVB (8844): dabusb_fpga_download(): fix a memory leak
V4L/DVB (8843): tda10048_firmware_upload(): fix a memory leak
V4L/DVB (8842): vivi_release(): fix use-after-free
V4L/DVB (8840): dib0700: add basic support for Hauppauge Nova-TD-500 (84xxx)
V4L/DVB (8839): dib0700: add comment to identify 35th USB id pair
V4L/DVB (8837): dvb: fix I2C adapters name size
V4L/DVB (8835): gspca: Same pixfmt as the sn9c102 driver and raw Bayer added in sonixb.
V4L/DVB (8834): gspca: Have a bigger buffer for sn9c10x compressed images.
V4L/DVB (8833): gspca: Cleanup the sonixb code.
V4L/DVB (8832): gspca: Bad pixelformat of vc0321 webcams.
...
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6:
acer-wmi: remove debugfs entries upon unloading
ACPI: Avoid bogus timeout about SMbus check
fujitsu-laptop: fix regression for P8010 in 2.6.27-rc
ACPI: Make Len Brown the ACPI maintainer again
ACPI: thinkpad-acpi: wan radio control is not experimental
PNPACPI: ignore the producer/consumer bit for extended IRQ descriptors
acpi: add checking for NULL early param
ACPI: Fix typo in "Disable MWAIT via DMI on broken Compal board"
ACPI: Fix now signed module parameter.
ACPI: Change package length error to warning
ACPI: Fix now signed module parameter.
Fix offset of second word used for programming base address of memory
window. Also program tmio with offset of the FCR, not with physical
memory location.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch teaches the i2c-sh_mobile driver to make use of wait irqs.
Without this patch only dte irqs are used which may lead to overruns
and cases of missing stop and extra bytes being read on the i2c bus.
Use of wait irqs forces the hardware to pause and wait until the cpu
is ready. Polling is also reworked in this patch to fix ms delay issues.
Verified with bus analyzer and tested on MigoR and AP325RXA boards.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Apparently, there are more different versions of Lenovo 3000 N100, some
of them working properly with active mux, and some of them requiring it
being switched off.
This patch applies 'nomux' only to the specific product name that is
reported to behave badly unless 'nomux' is specified.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The mousedev driver requires the use of BTN_TOUCH events to process
ABS_X and ABS_Y events properly, which is what is needed for the
bcm5974-based apple computers to have a functional pointer out-of-the-box.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The problem of finger tracking, i.e., when to switch focus from one
finger to another on the trackpad, has been improved by utilizing more
information from the bcm5974 chip output. This results in less pointer
hopping when many fingers are on the trackpad. In addition, a finger
counting method based on pressure information from all fingers is
introduced. Together with a pressure hysteresis window, this yields a
more stable counting of the number of fingers on the trackpad.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
While doing some testing using Luca Risolia's sonix driver I noticed that
the video device did not get ACL's set to allow access by locally logged in
users, nor does it show up as a video device in lshal, causing cheese to not
see it.
This turns out to be caused by all of Luca Risolia's drivers not setting
the parent member of the video_device struct. This patch fixes this.
Cc: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
b2c2-flexcop, dvb/bt8xx and video/bt8xx fails to build on ARM with:
__bad_udelay is specifically designed on ARM to fail when udelay is
called in a bad way. arch/arm/include/asm/delay.h has this to say
about __bad_udelay:
/*
* This function intentionally does not exist; if you see references to
* it, it means that you're calling udelay() with an out of range value.
*
* With currently imposed limits, this means that we support a max delay
* of 2000us. Further limits: HZ<=1000 and bogomips<=3355
*/
extern void __bad_udelay(void);
Solution is to replace udelay by a mdelay and udelay with value less than 2000
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
budget.ko fails to build on ARM with:
ERROR: "__bad_udelay" [drivers/media/dvb/ttpci/budget.ko] undefined!
make[1]: *** [__modpost] Error 1
__bad_udelay is specifically designed on ARM to fail when udelay is
called in a bad way. arch/arm/include/asm/delay.h has this to say
about __bad_udelay:
/*
* This function intentionally does not exist; if you see references to
* it, it means that you're calling udelay() with an out of range value.
*
* With currently imposed limits, this means that we support a max delay
* of 2000us. Further limits: HZ<=1000 and bogomips<=3355
*/
extern void __bad_udelay(void);
Solution is to replace udelay by a mdelay and udelay with value less than 2000
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Adjust hstart in ov7630 on sn9c103 initdata to shift bayer pattern, this is
the same change as done for the other initdata tables in a previous patch.
- Assign usb-id's for the ov7630 + sn9c103 to gspca if gspca and sn9c102
drivers are both enabled.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-Make raw bayer header size change from 20 to 16 affect rev072a only, my 2
rev012a cams both have a header size of 20
-While testing this I also tested the new exposure setting (good work on
finding the register JF), and after quite a bit of testing have found out the
exact meaning of the register, this patch modifies setexposure to control
the exposure over a much wider range.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When using the sonixb driver in a dark room and given that the autoexposure
algorithm starts with a setting most suitable for daylight, the picture
produced by the cam may actually be 100% black leading to a avg_lum value of 0,
so an avg_lum value of 0 does not always signal an exposure settings change
(which it normally does). This patch adds a check for the really black image
case and stops dropping all frames as invalid in this case.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes gspca claim the USB-ID for sn9c101/2 cams with a TAS5110C1B
sensor even if both gspca and sn9c102 are enabled, as these cams are much
better supported under gspca (and extensively tested with gspca).
It also removes an usb-id from sn9c102 for one more unsupported bridge
sensor combo.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Add documentation for some known registers
- Add support for vga modes (320x240, 160x120) for sif sensors
- Remove F_RAW sensor flag raw mode should work on any sensor as its a bridge
only thing and keeping the flag was becoming awkward.
- Fixup ov6650 and pas106 auto exposure window settings
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The exit function neglects to remove debugfs entries, leading to a BUG
on reload.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
In the function of wait_transaction_complete when the timeout happens,
OS will try to check the status of SMbus again. If the status is what OS
expected, it will be regarded as the bogus timeout. Otherwise it will be
treated as ETIME.
http://bugzilla.kernel.org/show_bug.cgi?id=10483
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
tested-by : Oldřich Jedlička < <oldium.pro@seznam.cz>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The following patch (based on a patch from Stephen Gildea) fixes a
regression with the LCD brightness keys on Fujitsu P8010 laptops which was
observed with the 2.6.27-rc series (basically they stopped working due to
changes within the fujitsu-laptop and video modules). Please apply to
2.6.27-rc and acpi git.
A more complete solution for this laptop will be included in an upcoming
patch, hopefully for 2.6.28. In the meantime this restores most
functionality for P8010 users.
Signed-off-by: Stephen Gildea <stepheng+fujitsu-laptop@gildea.com>
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
drivers/usb/host/ohci-omap.c: In function 'ohci_omap_init':
drivers/usb/host/ohci-omap.c:228: error: 'start_hnp' undeclared (first use in this function)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 884525655d ("PCI: clean up resource
alignment management") changed the resource handling to mark how a
resource was aligned on a per-resource basis.
Thus, instead of looking at the resource number to determine whether it
was a bridge resource or a regular resource (they have different
alignment rules), we should just ask the resource for its alignment
directly.
The reason this broke only cardbus resources was that for the other
types of resources, the old way of deciding alignment actually still
happened to work. But CardBus bridge resources had been changed by
commit 934b7024f0 ("Fix cardbus resource
allocation") to look more like regular resources than PCI bridge
resources from an alignment handling standpoint.
Reported-and-tested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2x: Accessing un-mapped page
ath9k: Fix TX control flag use for no ACK and RTS/CTS
ath9k: Fix TX status reporting
iwlwifi: fix STATUS_EXIT_PENDING is not set on pci_remove
iwlwifi: call apm stop on exit
iwlwifi: fix Tx cmd memory allocation failure handling
iwlwifi: fix rx_chain computation
iwlwifi: fix station mimo power save values
iwlwifi: remove false rxon if rx chain changes
iwlwifi: fix hidden ssid discovery in passive channels
iwlwifi: W/A for the TSF correction in IBSS
netxen: Remove workaround for chipset quirk
pcnet-cs, axnet_cs: add new IDs, remove dup ID with less info
ixgbe: initialize interrupt throttle rate
net/usb/pegasus: avoid hundreds of diagnostics
tipc: Don't use structure names which easily globally conflict.
The allocated RX buffer size was 64 bytes bigger than the PCI mapped
size with no good reason. If the packet was actually using the buffer up
to its limit and if the last 64 bytes of the buffer crossed 4KB boundary
then an unmapped PCI page was accessed. The fix is to use only one
parameter for the buffer size - there is no need to differentiate
between the buffer size and the PCI mapping size since the extra 64
bytes can actually be used by the FW to align the Ethernet payload to
64 bytes.
Also updating the driver version and date
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a memory leak in an error path.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_device_release() does kfree(), which made the following printk()
doing a use-after-free.
printk() first and release then.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds basic support for the Hauppauge Nova-TD-500 84xxx series.
A future patch will allow for one aerial input to supply both tuners.
With the current code, an aerial must be plugged into each antannae input
in order for both tuners to function.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This comment helps to make the code more readable.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some DVB drivers are incorrectly assuming that the size of
i2c_adapter.name is I2C_NAME_SIZE. Here's a fix.
Also change strncpy to strlcpy, as the former is error-prone (and was
indeed incorrectly used.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1) Lower the hstart setting for all sensor by 1 so that we generate
(compressed) BGGR data just like sn9c102 does (instead of GBRG data)
2) Add support for raw bayer output in the lowest resolutions (not enough
bandwidth for higher resolutions), this should work with all sensors but
to be sure only enable it for sensors where it has been tested.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Under certain conditions sonixb compressed frame size can get bigger then
the uncompressed size (seen with 0c45:6028), so make the buffers slightly
bigger.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-the usb-id table caried several flags which were not usb-id specific but
sensor specific, add a sensor_data array and move these flag there
-fr_h_sz was being abused to store and check which bridge was being used
instead add a bridge member to the sd struct
-now that we have a sensor_data table use that to store pointers to
init_sequences instead of using switch cases on sd->sensor
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-remove USB-id's from zc0301 for cams for which zc0301.c does not support
the sensor
-remove USB-id's from sn9c102 for cams where sn9c102 does not support the
bridge sensor combination
-no longer make inclusion of usb id's removed from zc0301 and sn9c102
conditional in gspca
-fix conditional inclusion of USB-id's in gspca to also work when the
conflicting drivers are build as a module
-add a number of USB-id's to gspca from various windows .inf files:
0c45:608f from generic sonix sn9c103 inf file (+ ov7630 which we support)
041e:4022 from creative webcam nx pro, same as already supported 041e:401e
0ac8:0301 from generic zc0301 driver which supports many sensors
10fd:804d from typhoon webshot driver (also FlyCAM-USB 300 plus)
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The USB buffer may be used for DMA and there may be a caching problem
if the buffer is part of the device structure.
Thanks to Alan Stern.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-Add usb id for 093a:2624 (pac7302)
-Report some controls to userspace with 7302 only, as they are 7302 only
-Add gain and exposure controls
-Add autogain
-Fix 7302 imaged being mirrored by default
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- the stream must stop when the main application closes the device.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- new function 'init' called on probe and resume
- remove the functions 'open' and 'closed'
- 'stopN' and 'stop0' are optional
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- turn the led of the cam off after plugging in the cam
- move the probe code from open to config, so that if the probe fails
we never register
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- set some controls as disabled instead of copying the device descr.
- in the ov6650 / 7650 exposure code clamp reg 11 before (instead of after)
using it to calculate reg 10.
- disable brightness (instead of ignoring it) for the TAS5110.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- documentation for some registers
- some preparations for adding autogain_n_exposure functionality
- various pac7311 fixes
- disable brightness and colors controls for 7311
- fix contrast control for 7311
- add hflip and vflip controls for 7311
- minimal jpeg header
- proper SOF detection
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I need this so I can better isolate my linux email from my
corporate email.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If apps pass QAM_AUTO then we need to obey it.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If apps pass QAM_AUTO then we need to obey it.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not a bug as such, but it looks really strange doing this before
checking whether the state structure could be allocated.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Simplify queue flush logic to prevent oops in cx18_flush_queues().
If accounting of a queue is in error, logic borrowed from ivtv will cause
an oops when flushing the queues for a stream. This change greatly
simplifies the queue flush logic, and sets the queue back to sane
defaults on a flush.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed a lot of sparse warnings: mostly warnings about shadowed variables
and signed/unsigned mismatches.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes several small issues at vivi register routines:
1) minor and n_devs should be unsigned;
2) n_devs = 0 were not properly handled;
3) if n_devs specify a high number, the driver would just roll back and
won't register any device. The proper behaviour is to keep all succeded
devices registered;
4) both n_devs and minor were using 0 as permissions. Better to have
them with 0444.
With the current patch, if n_devs specify a very large value, it will
register all possible devices. For example, on a machine without any
other V4L drivers loaded, with this patch, we will have something like:
vivi: V4L2 device registered as /dev/video0
vivi: V4L2 device registered as /dev/video1
vivi: V4L2 device registered as /dev/video2
...
vivi: V4L2 device registered as /dev/video31
video_register_device_index: get_index failed
Video Technology Magazine Virtual Video Capture Board ver 0.5.0 successfully loaded.
5) The number of allocated devices on success is now kept at n_devs:
$ cat /sys/module/vivi/parameters/n_devs
32
Thanks to Henne <henne@nachtwindheim.de> for pointing that there were
some issues at vivi.
Cc: Henne <henne@nachtwindheim.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Better check the video_device pointer before using it.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On 10-08-08 23:37, Alan Cox wrote:
>
> Would probably make the printk "pms: not enabled, use pms.enable=1 to
> probe"
>
> So you know
> a) What is wittering about not being probed
> b) How to undo it.
>
> But thats trivia really.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The old Mediavision Pro Movie Studio legacy ISA V4L1 driver was found to
hang the boot during Ingo Molnar's testing of randconfig kernels. Have it
require a "pms.enable=1" kernel parameter to enable the driver when
builtin which avoids such problems.
This is a deprecated and, very likely, unused driver. Nothing changes
modular behaviour moreover.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If saa7134_init is run before v4l2_i2c_drv_init (tuner), then
saa7134_board_init2 will try to set the tuner type for devices that don't
exist yet. This moves tuner to before all of the device-specific drivers
so that it's loaded early enough on boot.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This should have read, "GNU General Public License version 2"
rather than, "GNU General Public License version 3"
This was actually a typo mass-blunder -- this is not a change in licence,
as the code was always GPLv2.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a V4L2_CAP_SENSOR_UPSIDE_DOWN flag to the capabilities flags,
and sets this flag for the Philips SPC200NC cam (which has its sensor installed
upside down). The same flag is also needed and added for the Philips SPC300NC.
Together with a patch to libv4l which adds flipping the image in software this
fixes the upside down display with the SPC200NC cam.
Signed-of-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- return -EINVAL when control not supported.
- start the private controls at V4L2_CID_PRIVATE_BASE.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch adapted from a gspca v1 patch by Thomas Kaiser.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Add missing lock for when the irq handler manipulates the queues. This
was a potential source of stream queue corruption. Also changed the name of
cx18_queue_find_buf() to cx18_queue_get_buf_irq().
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If a wrong device type is used with video_register_device_index() it should
better return an error number, instead of a constant.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/v4l2-ioctl.c:496: warning: format '%08ld' expects
type 'long int', but argument 5 has type 'suseconds_t'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The CONFIG_RADIO_MIROPCM20{,_RDS} code became dead code 1.5 years ago.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The JPEG frames generated by the Pixart 73xx have:
- special markers 'ff ff ff xx' every 1024/512 bytes,
- unused 8 bits at end of JPEG blocks,
and then ask for a new pixel format.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Bug register/value inversions in USB exchanges.
Exposure and gain controls added for rev 12a.
Separate the functions and controls of the revisions 12a and 72a.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a double handling of 102c:6251 and no handling of 102c:6151
when both drivers GSPCA and ET61X251.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch moves the detection of the 2wr SIF pas106b sensor to before
detecting other sensors.
Patch change by jfm: Check SIF for identified webcams only.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The previous change in packet scanning did not work,
Also, autogain was no more treated at interrupt level.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Patch adapted from a patch to gspcav1 made by the google microdia group.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- change the work-queue to a single threaded high prio workqueue
- use DMA instead of PIO for the sliced VBI data.
- remove some incorrect tests
- increase the internal VBI capture queue size for sliced VBI packets
- ignore duplicate VBI lines
With these changes it should finally be possible to get reliable closed
captions.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since for 2.6.27 ivtvfb uses DMA for write it is important that
you can identify which ivtv version supports this and which doesn't.
Increase the version number so we can tell the difference.
Thanks to Ian Armstrong for pointing this out to me.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some drivers (e.g. zoran) have private V4L1 ioctls. Do not try to
pass them to v4l1_compat_translate because then the driver will
never see them.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Explicitly set 6 MHz IF frequency for VSB and QAM in
hauppauge_hvr950q_config.
The default value is 6 MHz, so this patch doesn't change anything --
this only improves code readability and may prevent future bugs.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since IF frequency is set after the vsb/qam modulation tables are written,
remove the redundant register settings from the vsb/qam modulation tables.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
re-write this function to make it simpler
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a mechanism to configure IF frequency for vsb and qam.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch sets STATUS_EXIT_PENDING on pci_remove. Otherwise
iwl4965_down may fail to uninitialize the driver.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch calls apm stop on exit and suspend. Without this patch
hardware consumes power even after driver is removed or suspended.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch "iwlwifi: do not use GFP_DMA in iwl_tx_queue_init" removes
GFP_DMA from allocation tx command buffers. GFP_DMA allows allocation
only for memory under 16M which causes allocation problems
suspend/resume flows.
Using kmalloc is temporal solution and some consistent/coherent
allocation schema will be more correct. Since iwlwifi hardware
supports 64bit address this solution should work on x86 (32 and
64bit) for now.
This patch fixes memory freeing problem in the previous patch.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes rx_chain computation. The code that adjusts number of
rx chains to number supported by HW was missing. Miss configuration
causes firmware error. Note: iwlwifi supports HW with up to 3 RX
chains (2x2, 2x3, 1x2, and 3x3 MIMO). This patch also simplifies the
whole RX chain computation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the wrong use MIMO power save values. Our TX was
configured with our MIMO power save values instead of peer's MIMO power
save values, this may affect connectivity. The peer STA/AP may not sense
our traffic at all as it doesn't have all RX chains opened.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx chain might change during power save transitions but it doesn't
require sending Full-ROXN command to the firmware. Full-RXON requires
reconnection to an AP and thus affects user experience. The patch
avoids the Full-RXON by removing the rx_chain modification check in
iwl_full_rxon_required function.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables sending of direct probes on passive channels, as long as
traffic was detected on that channel. This enables connectivity to
hidden/non broadcasting SSIDs APs on passive channels. Note 5000 HW
declares all 5.2 spectrum as passive.
Signed-off-by: Cahill Ben <ben.m.cahill@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is a W/A for the TSF sync issue in IBSS merging. HW is not
capable to sync TSF (it's constantly little behind). This creates
constant IBSS merging upon reception of each beacon, adding and removing
station which in turn creates above 50% packet loss and thus dramatically
degrade the throughput. The W/A simply stops the driver from declaring it
has a reliable TSF value and thus eliminates IBSS merging.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove chipset-specific quirk workaround; the workaround caused
unrecoverable DMA lockups when the driver was loaded following a
PXE boot.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This commit dropped the setting of the default interrupt throttle rate.
commit 021230d40a
Author: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Date: Mon Mar 3 15:03:45 2008 -0800
ixgbe: Introduce MSI-X queue vector code
The following patch adds it back. Without this the default value of 0
causes the performance of this card to be awful. Restoring these to the
default values yields much better performance.
This regression has been around since 2.6.25.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: stable@kernel.org [2.6.25 and later]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make the "pegasus" driver scream less loudly in the face of
problems as it initializes, avoiding hundreds of messages:
- ratelimit some key error messages
- avoid some spurious diagnostics caused by strange codeflow
And fix one instance of goofy indentation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipsec: Fix deadlock in xfrm_state management.
ipv: Re-enable IP when MTU > 68
net/xfrm: Use an IS_ERR test rather than a NULL test
ath9: Fix ath_rx_flush_tid() for IRQs disabled kernel warning message.
ath9k: Incorrect key used when group and pairwise ciphers are different.
rt2x00: Compiler warning unmasked by fix of BUILD_BUG_ON
mac80211: Fix debugfs union misuse and pointer corruption
wireless/libertas/if_cs.c: fix memory leaks
orinoco: Multicast to the specified addresses
iwlwifi: fix 64bit platform firmware loading
iwlwifi: fix apm_stop (wrong bit polarity for FLAG_INIT_DONE)
iwlwifi: workaround interrupt handling no some platforms
iwlwifi: do not use GFP_DMA in iwl_tx_queue_init
net/wireless/Kconfig: clarify the description for CONFIG_WIRELESS_EXT_SYSFS
net: Unbreak userspace usage of linux/mroute.h
pkt_sched: Fix locking of qdisc_root with qdisc_root_sleeping_lock()
ipv6: When we droped a packet, we should return NET_RX_DROP instead of 0
Fix a bug reported by and diagnosed by Aaron Straus.
This is a regression intruduced into 2.6.26 by
commit adc782dae6
Author: Matt Mackall <mpm@selenic.com>
Date: Tue Apr 29 01:03:07 2008 -0700
random: simplify and rename credit_entropy_store
credit_entropy_bits() does:
spin_lock_irqsave(&r->lock, flags);
...
if (r->entropy_count > r->poolinfo->POOLBITS)
r->entropy_count = r->poolinfo->POOLBITS;
so there is a time window in which this BUG_ON():
static size_t account(struct entropy_store *r, size_t nbytes, int min,
int reserved)
{
unsigned long flags;
BUG_ON(r->entropy_count > r->poolinfo->POOLBITS);
/* Hold lock while accounting */
spin_lock_irqsave(&r->lock, flags);
can trigger.
We could fix this by moving the assertion inside the lock, but it seems
safer and saner to revert to the old behaviour wherein
entropy_store.entropy_count at no time exceeds
entropy_store.poolinfo->POOLBITS.
Reported-by: Aaron Straus <aaron@merfinllc.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update rtc-cmos shutdown handling to leave RTC alarms active, resolving
http://bugzilla.kernel.org/show_bug.cgi?id=11411 on several boards. There
are still some systems where the ACPI event handling doesn't cooperate.
(Possibly related to bugid 11312, reporting the spontaneous disabling of
RTC events.)
Bug 11411 reported that changes to work around some ACPI event issues
broke wake-from-S5 handling, as used for DVR applications. (They like to
power off, then wake later to record programs.)
[yakui.zhao@intel.com: add shutdown for PNP devices]
[dbrownell@users.sourceforge.net: update comments]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Stefan Bauer <stefan.bauer@cs.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I got this patch through Red Hat's bugzilla from the bug submitter and
patch creator. I have just fixed it up so it applies without fuzz to
upstream kernels.
Original patch and description from Shyam kumar Iyer:
The issue [ibft module not displaying targets with short names] is because
of an offset calculatation error in the iscsi_ibft.c code. Due to this
error directory structure for the target in /sys/firmware/ibft does not
get created and so the initiator is unable to connect to the target.
Note that this bug surfaced only with an name that had a short section at
the end. eg: "iqn.1984-05.com.dell:dell". It did not surface when the
iqn's had a longer section at the end. eg:
"iqn.2001-04.com.example:storage.disk2.sys1.xyz"
So, the eot_offset was calculated such that an extra 48 bytes i.e. the
size of the ibft_header which has already been accounted was subtracted
twice.
This was not evident with longer iqn names because they would overshoot
the total ibft length more than 48 bytes and thus would escape the bug.
Signed-off-by: Shyam Kumar Iyer <shyam_iyer@dell.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Konrad Rzeszutek <konrad@virtualiron.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 945185a69d ("rtc: rtc_time_to_tm: use
unsigned arithmetic") changed the some types in rtc_time_to_tm() to
unsigned:
void rtc_time_to_tm(unsigned long time, struct rtc_time *tm)
{
- register int days, month, year;
+ unsigned int days, month, year;
This doesn't work for all cases, because days is checked for < 0 later
on:
if (days < 0) {
year -= 1;
days += 365 + LEAP_YEAR(year);
}
I think the correct fix would be to keep days signed and do an appropriate
cast later on.
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there are more then one graphics card handled by the tdfxfb driver the
name of the frame buffer overruns reserved size.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix memory detection on Voodoo3 cards with SDRAM memory.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that event 0x4 merely indcates that a hotkey has been
pressed, not which one. A further query is required in order to determine
the actual keypress. The following patch adds support for that along with
the known keycodes.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hp-wmi currently changes the RFKill state by altering the struct members
rather than using the dedicated interface, meaning that update events
won't be pushed to userspace. This patch fixes that, along with fixing
the declared type of the WWAN kill switch. It also ensures that rfkill
interfaces are only registered for hardware that exists.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <ivdoorn@gmail.com>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Check if virtual resolution fits into memory.
Otherwise, Linux hangs during panning.
2. When selected use all available memory to
maximize yres_virtual to speed up panning
(previously also xres_virtual was increased).
3. Simplify memory restriction calculations.
Signed-off-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At91_mci is abusing dma_free_coherent(), which may not be called with IRQs
disabled. I saw "mkfs.ext3" on an MMC card objecting voluminously as each
write completed:
WARNING: at arch/arm/mm/consistent.c:368 dma_free_coherent+0x2c/0x224()
[<c002726c>] (dump_stack+0x0/0x14) from [<c00387d4>] (warn_on_slowpath+0x4c/0x68)
[<c0038788>] (warn_on_slowpath+0x0/0x68) from [<c0028768>] (dma_free_coherent+0x2c/0x224)
r6:00008008 r5:ffc06000 r4:00000000
[<c002873c>] (dma_free_coherent+0x0/0x224) from [<c01918ac>] (at91_mci_irq+0x374/0x420)
[<c0191538>] (at91_mci_irq+0x0/0x420) from [<c0065d9c>] (handle_IRQ_event+0x2c/0x6c)
...
This bug has been around for a LONG time. The MM warning is from late
2005, but the driver merged a year later ... so I'm puzzled why nobody
noticed this before now.
The fix involves noting that this buffer shouldn't be DMA-coherent; it's
just used for normal DMA writes. So replace it with standard kmalloc()
buffering and DMA mapping calls.
This is the quickie fix. A better one would not rely on allocating large
bounce buffers. (Note that dma_alloc_coherent could have failed too, but
that case was ignored... kmalloc is a bit more likely to fail though.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus-mmc@drzeus.cx>
Cc: Andrew Victor <linux@maxim.org.za>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent changes to tighten the check for UARTs that don't correctly
re-assert THRE (01c194d927: "serial 8250:
tighten test for using backup timer") caused problems when such a UART was
opened for the second time - the bug could only successfully be detected
at first initialization. For users of this version of this particular
UART IP it is fatal.
This patch stores the information about the bug in the bugs field of the
port structure when the port is first started up so subsequent opens can
check this bit even if the test for the bug fails.
David Brownell: "My own exposure to this is that the UART on DaVinci
hardware, which TI allegedly derived from its original 16550 logic, has
periodically gone from working to unusable with the mainline 8250.c ...
and back and forth a bunch. Currently it's "unusable", a regression from
some previous versions. With this patch from Will, it's usable."
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Alex Williamson <alex.williamson@hp.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The exit function neglects to remove debugfs entries, leading to a BUG
on reload.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch addresses an issue with the locking order. ath_rx_flush_tid()
uses spin_lock/unlock_bh when IRQs are disabled in sta_notify by mac80211.
As node clean up is still pending with ath9k and this problematic portion
of the code is expected to change anyway, thinking of a proper fix may not
be worthwhile. So having this interim fix helps the users to get rid of the
kernel warning message.
Pasted the kernel warning message for reference.
kernel: ath0: No ProbeResp from current AP 00:1b:11:60:7a:3d - assume out of range
kernel: ------------[ cut here ]------------
kernel: WARNING: at kernel/softirq.c:136 local_bh_enable+0x3c/0xab()
kernel: Pid: 1029, comm: ath9k Not tainted 2.6.27-rc4-wt-w1fi-wl
kernel:
kernel: Call Trace:
kernel: [<ffffffff802278d8>] warn_on_slowpath+0x51/0x77
kernel: [<ffffffff80224c51>] check_preempt_wakeup+0xf3/0x123
kernel: [<ffffffff80239658>] autoremove_wake_function+0x9/0x2e
kernel: [<ffffffff8022c281>] local_bh_enable+0x3c/0xab
kernel: [<ffffffffa01ab75a>] ath_rx_node_cleanup+0x38/0x6e [ath9k]
kernel: [<ffffffffa01b2280>] ath_node_detach+0x3b/0xb6 [ath9k]
kernel: [<ffffffffa01ab09f>] ath9k_sta_notify+0x12b/0x165 [ath9k]
kernel: [<ffffffff802366cf>] queue_work+0x1d/0x49
kernel: [<ffffffffa018c3fc>] add_todo+0x70/0x99 [mac80211]
kernel: [<ffffffffa017de76>] __sta_info_unlink+0x16b/0x19e [mac80211]
kernel: [<ffffffffa017e6ed>] sta_info_unlink+0x18/0x43 [mac80211]
kernel: [<ffffffffa0182732>] ieee80211_associated+0xaa/0x16d [mac80211]
kernel: [<ffffffffa0184a1a>] ieee80211_sta_work+0x4fb/0x6b4 [mac80211]
kernel: [<ffffffff80469c58>] thread_return+0x30/0xa9
kernel: [<ffffffffa018451f>] ieee80211_sta_work+0x0/0x6b4 [mac80211]
kernel: [<ffffffff802362c2>] run_workqueue+0xb1/0x17a
kernel: [<ffffffff80236be9>] worker_thread+0xd0/0xdb
kernel: [<ffffffff8023964f>] autoremove_wake_function+0x0/0x2e
kernel: [<ffffffff80236b19>] worker_thread+0x0/0xdb
kernel: [<ffffffff8023954a>] kthread+0x47/0x75
kernel: [<ffffffff80223121>] schedule_tail+0x18/0x50
kernel: [<ffffffff8020bc49>] child_rip+0xa/0x11
kernel: [<ffffffff80239503>] kthread+0x0/0x75
kernel: [<ffffffff8020bc3f>] child_rip+0x0/0x11
kernel:
kernel: ---[ end trace e9bb5da661055827 ]---
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updating sc_keytype multiple times when groupwise and pairwise
ciphers are different results in incorrect pairwise key type
assumed for TX control and normal ping fails. This works fine
for cases where both groupwise and pairwise ciphers are same.
Also use mac80211 provided enums for key length calculation.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A "Set" to a sign-bit in an "&" operation causes a compiler warning.
Make calculations unsigned.
[ The warning was masked by the old definition of BUILD_BUG_ON() ]
Also remove __builtin_constant_p from FIELD_CHECK since BUILD_BUG_ON
no longer permits non-const values.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The leak in if_cs_prog_helper() is obvious.
It looks a bit as if not freeing "fw" in if_cs_prog_real() was done
intentionally, but I'm not seeing why it shouldn't be freed.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multicasting the driver sets the number of group addresses using
the count from the previous set multicast command. In general this means
you have to set the multicast addresses twice to get the behaviour you
want.
If we were multicasting, and reduce the number of addresses we are
multicasting to, then the driver would write uninitialised data from the
stack into the group addresses to multicast to.
Only write the multicast addresses we have specifically set.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes loading firmware from memory above 32bit.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Marcel Holtmann <holtmann@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes CSR_GP_CNTRL_REG_FLAG_INIT_DONE was set instead of
cleared which disabled moving device to D0U state.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds workaround for an interrupt related hardware bug on
some platforms. (Apparently these platforms boot-up w/ INTX_DISABLED
set. -- JWL)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the RAE (remote access enable) bit and correctly initialize the
MTT size in MPT entries being set up for fast register memory
regions. Otherwise the callers can't enable remote access and in fact
can't fast register at all (since the HCA will think no MTT entries
are allocated).
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
GFP_DMA is not necessary for the iwlwifi hardware and it can cause
allocation failures and/or invoke the OOM killer on lots of systems.
For reference:
https://bugzilla.redhat.com/show_bug.cgi?id=459709
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* fix device tree ... don't forget to set the parent device
* let init/exit code be removed where practical
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
[bart: splitted it from bigger DaVinci patch, s/hw.parent/hw.dev/]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'for-linus' of git://neil.brown.name/md:
Fix problem with waiting while holding rcu read lock in md/bitmap.c
Remove invalidate_partition call from do_md_stop.
This fixes a typo in commit 2a2a64714d "Disable MWAIT via DMI on broken Compal board".
It allows the nomwait dmi check to actually detect the Acer 5220.
Signed-off-by: Dennis Jansen <dennis.jansen@web.de>
Tested-by: Dennis Jansen <dennis.jansen@web.de>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MEMGETREGIONINFO ioctl() in mtdchar.c was clobbering user memory by
overwriting more than intended, due the size of struct mtd_erase_region_info
changing in commit 0ecbc81adf ('Support
for auto locking flash on power up').
Fix avoids this by copying struct members one by one with put_user(), as there
is no longer a convenient struct to use the size of as the length argument to
copy_to_user().
Signed-off-by: Zev Weiss <zevweiss@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes a memory leak in an error path.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The interrupt handler for muxed interrupts (imx2/imx3) was calling
the rts handling subroutine if the RTSS bit was set.
(Which indicates the status of the RTS line), leading to an
interrupt flood on RTS bit low.
This patch fixes the problem by looking at the RTSD bit instead,
indicating a change in the RTS line.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
RX in i.MX27 and i.MX31 UART lines does not work unless the
"RXD Muxed Input Select" bit is set on i.MX27 and i.MX31 processors.
This patch sets the missing RXD mux bit in the UCR3 register.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adds extra "out" label to probe function after calling .init form platform data.
Because .init can return error number caused by gpio request fail.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A recent patch to protect the rdev list with rcu locking leaves us
with a problem because we can sleep on memalloc while holding the
rcu lock.
The rcu lock is only needed while walking the linked list as
uninteresting devices (failed or spares) can be removed at any time.
So only take the rcu lock while actually walking the linked list.
Take a refcount on the rdev during the time when we drop the lock
and do the memalloc to start IO.
When we return to the locked code, all the interesting devices
on the list will not have moved, so we can simply use
list_for_each_continue_rcu to pick up where we left off.
Signed-off-by: NeilBrown <neilb@suse.de>
When stopping an md array, or just switching to read-only, we
currently call invalidate_partition while holding the mddev lock.
The main reason for this is probably to ensure all dirty buffers
are flushed (invalidate_partition calls fsync_bdev).
However if any dirty buffers are found, it will almost certainly cause
a deadlock as starting writeout will require an update to the
superblock, and performing that updates requires taking the mddev
lock - which is already held.
This deadlock can be demonstrated by running "reboot -f -n" with
a root filesystem on md/raid, and some dirty buffers in memory.
All other calls to stop an array should already happen after a flush.
The normal sequence is to stop using the array (e.g. umount) which
will cause __blkdev_put to call sync_blockdev. Then open the
array and issue the STOP_ARRAY ioctl while the buffers are all still
clean.
So this invalidate_partition is normally a no-op, except for one case
where it will cause a deadlock.
So remove it.
This patch possibly addresses the regression recored in
http://bugzilla.kernel.org/show_bug.cgi?id=11460
and
http://bugzilla.kernel.org/show_bug.cgi?id=11452
though it isn't yet clear how it ever worked.
Signed-off-by: NeilBrown <neilb@suse.de>
If this triggers its bad, however some machines seem to have been
triggering it for ages and we didn't know until we added the debug.
So downgrade the debug now so people don't call this a regression.
Signed-off-by: Dave Airlie <airlied@redhat.com>
For IBM z series certain LUNs can no longer be accessed.
This is because kernel version 2.6.19 a check was introduced not to
create a generic SCSI device for devices that return PQ=1 and
PDT=0x1f. For WLUNs (see SAM-3, p. 41ff) generic SCSI devices should
be created unconditionally without looking at the PQ bit, so add a
check for WLUNs in with this test.
Acked-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Change scsi_check_sense HARDWARE_ERROR check to return ADD_TO_MLQUEUE
if device->retry_hwerror is set to allow retries to occur without
restriction of blk_noretry_request check.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Change scsi_dh check_sense functions to return ADD_TO_MLQUEUE
to allow retries to occur without restriction of blk_noretry_request
check.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some drivers have duplicated unlikely() macros. IS_ERR() already
has unlikely() in itself. This patch cleans up such pointless
codes although there is no real effect on the kernel's behaviour.
Signed-off-by: Hirofumi Nakagawa <hnakagawa@miraclelinux.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Due to an imbalance of the nameserver refcounting, channel devices
couldn't be take offline anymore after the channel was activated.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix the remote port reference counter handling during ELS ADISC
commands and find the remote port by WWPN not by D_IDs that could
change.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The notify handler does not change the list of adapters, it only
triggers erp actions to open or shutdown the adapter. We don't
need to hold the config semaphore and wait for the erp to complete.
This is a prerequisite for a fix in the s390 common i/o code.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When the last port entry in the gpn_ft response is already a known
port, the eval function would skip the end flag and try to attach
ports with wwpn 0. Fix this by checking the flag first.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The request queue lock can be acquired from softirq context when the
SCSI midlayer issues commands. Disable softirqs for this lock when
commands are issued from zfcp.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch remove blk_register_filter and blk_unregister_filter in
gendisk, and adds them to sd.c, sr.c. and ide-cd.c
The commit abf5439370 moved cmdfilter
from gendisk to request_queue. It turned out that in some subsystems
multiple gendisks share a single request_queue. So we get:
Using physmap partition information
Creating 3 MTD partitions on "physmap-flash":
0x00000000-0x01c00000 : "User FS"
0x01c00000-0x01c40000 : "booter"
kobject (8511c410): tried to init an initialized object, something is seriously wrong.
Call Trace:
[<8036644c>] dump_stack+0x8/0x34
[<8021f050>] kobject_init+0x50/0xcc
[<8021fa18>] kobject_init_and_add+0x24/0x58
[<8021d20c>] blk_register_filter+0x4c/0x64
[<8021c194>] add_disk+0x78/0xe0
[<8027d14c>] add_mtd_blktrans_dev+0x254/0x278
[<8027c8f0>] blktrans_notify_add+0x40/0x78
[<80279c00>] add_mtd_device+0xd0/0x150
[<8027b090>] add_mtd_partitions+0x568/0x5d8
[<80285458>] physmap_flash_probe+0x2ac/0x334
[<802644f8>] driver_probe_device+0x12c/0x244
[<8026465c>] __driver_attach+0x4c/0x84
[<80263c64>] bus_for_each_dev+0x58/0xac
[<802633ec>] bus_add_driver+0xc4/0x24c
[<802648e0>] driver_register+0xcc/0x184
[<80100460>] _stext+0x60/0x1bc
In the long term, we need to fix such subsystems but we need a quick
fix now. This patch add the command filter support to only sd and sr
though it might be useful for other SG_IO users (such as cciss).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reported-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: Fix PM building on BF52x: No ROTWE on BF52x, add USBWE
Blackfin arch: sram: use 'unsigned long' for irqflags
Blackfin arch: let PCI depend on BROKEN
Blackfin arch: move include/asm-blackfin header files to arch/blackfin
Blackfin arch: fix bug - MPU crashes under stress
Blackfin arch: Fix bug - when to rmmod the L1_module, it stucks and then reboot the board.
Blackfin arch: dont actually need to muck with EMAC_SYSTAT for BF52x for demuxing
Blackfin arch: Add MTD Partitions for MTD_DATAFLASH, increase max SPI SCLK
The WWAN radio control has been working well for over three years,
and is no longer experimental.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Some DVB adapters do not support the special I2C transaction that we
use for probing purposes. There's no point in logging this event, as
there's nothing the user can do and in general there is no actual
problem. So, degrade one of these messages to a debug message, and
move the other one around so that it is only printed on bogus drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
device_init_wakeup must be called after device_register.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Initialize the L_Key and R_Key for memory regions returned from
mlx4_ib_alloc_fast_reg_mr(). Otherwise callers just get garbage for
the memory keys and can't do anything useful with these MRs.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kanru Chen posted a patch versus the old code which deals with the case
where you resize the pty side of a pty/tty pair. In that situation the
termios data is updated for both pty and tty but the locks are not held
for the right side.
This implements the fix differently against the updated tty code. Patch
by self but the hard bit (noticing and fixing the bug) is thanks to Kanru
Chen.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The termios settings ioctls on a pty should affect the bound tty side not
the pty. The SOFTCAR ioctls use the wrong device file.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: don't set the signal blocker on the master process.
drm: don't call the vblank tasklet with irqs disabled.
r300: Fix cliprect emit
drm/radeon: r300_cmdbuf: Always emit INDX_BUFFER immediately after DRAW_INDEX
radeon: fix some hard lockups on r3/4/500s
Here's the patch. It shrinks the stack from 1152 bytes to 192 bytes (the
first version, that only did the e1000_option part, got it down to 600
bytes). About half comes from not using multiple "e1000_option"
structures, the other half comes from turning the "e1000_opt_list[]"
arrays into "static const" instead, so that gcc doesn't copy them onto the
stack.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reveiewed-by: Auke Kok <auke-jan.h.kok@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: remove blk_queue_tag_depth() and blk_queue_tag_queue()
block: remove unused ->busy part of the block queue tag map
bio: fix __bio_copy_iov() handling of bio->bv_len
bio: fix bio_copy_kern() handling of bio->bv_len
block: submit_bh() inadvertently discards barrier flag on a sync write
block: clean up cmdfilter sysfs interface
block: rename blk_scsi_cmd_filter to blk_cmd_filter
sg: restore command permission for TYPE_SCANNER
block: move cmdfilter from gendisk to request_queue
This reverts commit 5b6155ee70, because
the block device ioctl's really aren't ready for it.
In particular, the "struct file *" and the "struct inode *" arguments do
not necessarily match, which means that the unlocked version of the
ioctl (that only gets a "struct file *") isn't actually able to handle
the cases it needs to handle.
This fixes bugzilla
http://bugzilla.kernel.org/show_bug.cgi?id=11401
Reported-and-bisected-by: Laurent Riffard <laurent.riffard@free.fr>
Acked-by: Peter Osterlund <petero2@telia.com>
Cc: Alan Cox <alan@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There were 2 omitted readb's used on an iomap space. eliminate them
by using ioread8 instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When a preallocated header qdio buffer is filled we have to account
the offset for the data length.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In case the netdev unicast list contains additional entries we have
to register/deregister them.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
return value -ENOTSUPP is not valid in userspace context, use
-EOPNOTSUPP instead.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We must not call dev_mc_add() from within our HW configure which happens
before we initialize and register the netdev. Do it in open() instead.
Thanks to Sebastian Siewior for tracking it down.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the checksum feature advertised in device flags. The hardware support
TCP/UDP over IPv4 and TCP/UDP over IPv6 (without IPv6 extension headers).
However, the kernel feature flags do not distinguish IPv6 with/without
extension headers.
Therefore, the driver needs to use NETIF_F_IP_CSUM instead of
NETIF_F_HW_CSUM since the latter includes all IPv6 packets.
A future patch can be created to check for extension headers and perform
software checksum calculation.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Manfred Spraul <manfred@colorfullife.com
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement set_mac_address for mcs7830. This enables me to use it with my
cable modem.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This adds USB device IDs for MosChip 7730 and Sitecom LN030
to the mcs7830 driver. The IDs have been reported to work without
further modifications.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Viktor Horvath <ViktorHorvath@gmx.net>
Cc: Robbert Wethmar <robbert@wethmar.nl>
Cc: Bart van der Klip <bklip@xs4all.nl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes a ibmveth bug where bad UDP checksums are being transmitted
when checksum offloading is enabled.
The hypervisor does checksum offloading only on TCP packets, so ibmveth calls
skb_checksum_help() for any other protocol. The bug happens because
the packet is being modified after the DMA map, so we would need a memory
barrier before making the hypervisor call. Reordering the code so that the
DMA map happens after skb_checksum_help() has the additional advantage of
fixing a DMA map leak if skb_checksum_help() where to fail.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes dev_kfree_skb happening too many times when hso_start_net_device
is called from hso_resume.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The atl1 driver is causing stalled connections and file corruption
whenever TSO is enabled. Two examples are here:
http://lkml.org/lkml/2008/7/15/325http://lkml.org/lkml/2008/8/18/543
Disable TSO by default until we can determine the source of the
problem.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Doesn't cause problems (yet) because err gets zeroed earlier.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Disable support for device 8086:10E8. Currently the result of loading the
driver with the device present causes system instability.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
CC [M] drivers/net/skfp/ess.o
drivers/net/skfp/ess.c: In function 'ess_send_response':
drivers/net/skfp/ess.c:513: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c: In function 'ess_send_alc_req':
drivers/net/skfp/ess.c:609: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c:639: warning: cast from pointer to integer of different size
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
LCS recovery dumps in irq routine when CCW address in
Subchannel Status Word (SCSW) is zero. This occurs
when recovery is driven after cable reconnect.
Signed-off-by: Klaus-D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use netdev->ml_priv instead of netdev->priv
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use netdev->ml_priv instead of netdev->priv
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
probe_error() frees memory only, if cgdev->dev.driver_data refers
to the claw_privbk structure. Move forward its setting in claw_probe()
to ensure proper freeing of claw_privbk allocations.
Cc: Daniel <danielm77@spray.se>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The real_num_tx_queues was not being set when in MSI-X only mode. This patch
corrects that path so all interrupt types are correctly configured.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ethtool -d is reading the EICR and ICR registers which is currently
clearing these registers and masking off interrupts. To prevent this we
read the EICS and ICS equivilents as they can be read without clearing or
masking.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
