The RZ/G2L multi-function timer pulse unit 3 (MTU3a) is embedded in
the Renesas RZ/G2L family SoCs. It consists of eight 16-bit timer
channels and one 32-bit timer channel. It supports the following
functions
- Counter
- Timer
- PWM
The 8/16/32 bit registers are mixed in each channel.
Add MTU3a core driver for RZ/G2L SoC. The core driver shares the
clk and channel register access for the other child devices like
Counter, PWM and Clock event.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230330111632.169434-3-biju.das.jz@bp.renesas.com
This driver cannot be built as a module, so don't suggest otherwise
in Kconfig help.
Suggested-by: Lee Jones <lee@kernel.org>
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Reviewed-by: Vincenzo Palazzo <vincenzopalazzodev@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Implement a regulator driver with IRQ support for fault management.
Written against documentation [1] and [2] and tested on real hardware.
Every channel has it's own regulator supply nammed 'vss1-supply' and
'vss2-supply'. The regulator supply is used to determine the output
voltage, as the smart switch provides no output regulation.
The driver requires the 'shunt-resistor-micro-ohms' to be present in
the devicetree to properly calculate current related values.
You must specify compatible devictree layout:
regulator@3a {
reg = <0x3a>;
vss1-supply = <&p3v3>;
compatible = "maxim,max5978";
...
regulators {
sw0_ref: SW0 {
regulator-compatible = "SW0";
shunt-resistor-micro-ohms = <12000>;
...
}
}
}
1: https://datasheets.maximintegrated.com/en/ds/MAX5970.pdf
2: https://datasheets.maximintegrated.com/en/ds/MAX5978.pdf
...
Changes in V12:
- Use simple_mfd_i2c driver and remove previous implementation.
- Remove newline
- Use _MFD_MAX597X_H in header file
- Successfull build need following patch from regulator:
https://lore.kernel.org/r/20230216075302.68935-1-Naresh.Solanki@9elements.comhttps://lore.kernel.org/r/20230210163225.1208035-1-Naresh.Solanki@9elements.com
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230307121246.127425-2-Naresh.Solanki@9elements.com
- Change MFD support status from Supported to Maintained
- New Drivers
- Add support for the Intel Platform Management Component Interface (PMCI)
- Remove Drivers
- HTC PASIC3 LED/DS1WM
- Toshiba T7L66XB, TC6387XB and TC6393XB TMIO
- New Device Support
- Add support for N6000 Flash to Intel M10 BMC PMCI
- Add support for Lenovo Yoga Tab 3 to Intel CHTWC PMIC
- New Functionality
- Provide Reset support to Syscon
- Fix-ups
- Explicitly provide missing include files
- Pass platform type data/info via the SPI/I2C/DT registration strategy
- Lots of DT documentation / adaptions
- Replace scnprintf() with preferred sysfs_emit()
- Remove unused / superfluous code
- Fix some trivial whitesspace / spelling / grammatical issues
- Replace pm_power_off with new and improved register_sys_off_handler() API
- Bug Fixes
- Reintroduce RK808-clkout registration - fixing Wi-Fi and Bluetooth
- Repair the order of AXPxxx IRQ PEK RISE/FALL definitions
- Refuse to build CS5535 on unsupported UML architectures
- Fix memory leaks in error return paths
- Prevent refcount leaks in error return paths
-----BEGIN PGP SIGNATURE-----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=f0fr
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Change MFD support status from Supported to Maintained
New Drivers:
- Add support for the Intel Platform Management Component Interface
(PMCI)
Removed Drivers:
- HTC PASIC3 LED/DS1WM
- Toshiba T7L66XB, TC6387XB and TC6393XB TMIO
New Device Support:
- Add support for N6000 Flash to Intel M10 BMC PMCI
- Add support for Lenovo Yoga Tab 3 to Intel CHTWC PMIC
New Functionality:
- Provide Reset support to Syscon
Fix-ups:
- Explicitly provide missing include files
- Pass platform type data/info via the SPI/I2C/DT registration
strategy
- Lots of DT documentation / adaptions
- Replace scnprintf() with preferred sysfs_emit()
- Remove unused / superfluous code
- Fix some trivial whitesspace / spelling / grammatical issues
- Replace pm_power_off with new and improved
register_sys_off_handler() API
Bug Fixes:
- Reintroduce RK808-clkout registration - fixing Wi-Fi and Bluetooth
- Repair the order of AXPxxx IRQ PEK RISE/FALL definitions
- Refuse to build CS5535 on unsupported UML architectures
- Fix memory leaks in error return paths
- Prevent refcount leaks in error return paths"
* tag 'mfd-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (40 commits)
dt-bindings: mfd: qcom,tcsr: Add compatible for IPQ5332
dt-bindings: mfd: Add NXP BBNSM
mfd: ntxec: Add version number for EC in Tolino Vision
dt-bindings: mfd: syscon: Add mt8365-syscfg
mfd: Remove toshiba tmio drivers
mfd: arizona: Use pm_runtime_resume_and_get() to prevent refcnt leak
mfd: syscon: Allow reset control for syscon devices
dt-bindings: mfd/syscon: Add resets property
dt-bindings: mfd: syscon: Add amd,pensando-elba-syscon compatible
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8226
mfd: simple-mfd-i2c: Fix incoherent comment regarding DT registration
mfd: axp20x: Switch to the sys-off handler API
mfd: core: Spelling s/compement/complement/
mfd: max8925: Remove the unused function irq_to_max8925()
mfd: qcom-pm8xxx: Remove set but unused variable 'rev'
dt-bindings: mfd: syscon: Document GXP register compatible
mfd: twl4030-power: Drop empty platform remove function
mfd: twl: Fix TWL6032 phy vbus detection
mfd: pcf50633-adc: Fix potential memleak in pcf50633_adc_async_read()
MAINTAINERS: Move MFD from a Supported to Maintaied state
...
Four separate mfd drivers are in the "tmio" family, and all of
them were used in now-removed PXA machines (eseries, tosa, and
hx4700), so the mfd drivers and all its children can be removed
as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230105134622.254560-19-arnd@kernel.org
The cs5535-mfd driver uses CPU-specific data that is not available
for ARCH=um builds, so don't allow it to be built for UML.
Prevents these build errors:
In file included from ../arch/x86/include/asm/olpc.h:7,
from ../drivers/mfd/cs5535-mfd.c:17:
../arch/x86/include/asm/geode.h: In function ‘is_geode_gx’:
../arch/x86/include/asm/geode.h:16:31: error: ‘struct cpuinfo_um’ has no member named ‘x86_vendor’
16 | return ((boot_cpu_data.x86_vendor == X86_VENDOR_NSC) &&
../arch/x86/include/asm/geode.h:16:46: error: ‘X86_VENDOR_NSC’ undeclared (first use in this function); did you mean ‘X86_VENDOR_ANY’?
16 | return ((boot_cpu_data.x86_vendor == X86_VENDOR_NSC) &&
../arch/x86/include/asm/geode.h:17:31: error: ‘struct cpuinfo_um’ has no member named ‘x86’
17 | (boot_cpu_data.x86 == 5) &&
../arch/x86/include/asm/geode.h:18:31: error: ‘struct cpuinfo_um’ has no member named ‘x86_model’
18 | (boot_cpu_data.x86_model == 5));
../arch/x86/include/asm/geode.h: In function ‘is_geode_lx’:
../arch/x86/include/asm/geode.h:23:31: error: ‘struct cpuinfo_um’ has no member named ‘x86_vendor’
23 | return ((boot_cpu_data.x86_vendor == X86_VENDOR_AMD) &&
../arch/x86/include/asm/geode.h:23:46: error: ‘X86_VENDOR_AMD’ undeclared (first use in this function); did you mean ‘X86_VENDOR_ANY’?
23 | return ((boot_cpu_data.x86_vendor == X86_VENDOR_AMD) &&
../arch/x86/include/asm/geode.h:24:31: error: ‘struct cpuinfo_um’ has no member named ‘x86’
24 | (boot_cpu_data.x86 == 5) &&
../arch/x86/include/asm/geode.h:25:31: error: ‘struct cpuinfo_um’ has no member named ‘x86_model’
25 | (boot_cpu_data.x86_model == 10));
Fixes: 68f5d3f3b6 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221201012541.11809-1-rdunlap@infradead.org
The htc-pasic3 MFD device was only used in the PXA magician
machine that is now removed, so this can be recycled as well.
Cc: Lee Jones <lee@kernel.org>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ucb1400 MFD driver and its gpio and touchscreen child
drivers were only used on a few PXA machines that were unused
for a while and are now removed.
Removing these leaves the AC97 support as ALSA specific,
no other drivers are now connected through this interface.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Lee Jones <lee@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Marek Vasut <marex@denx.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Four separate mfd drivers are in the "tmio" family, and all of
them were used in now-removed PXA machines (eseries, tosa, and
hx4700), so the mfd drivers and all its children can be removed
as well.
Cc: Lee Jones <lee@kernel.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the mfd driver for the Platform Management Component Interface
(PMCI) based interface of Intel MAX10 BMC controller.
PMCI is a software-visible interface, connected to card BMC which
provided the basic functionality of read/write BMC register. The access
to the register is done indirectly via a hardware controller/bridge
that handles read/write/clear commands and acknowledgments for the
commands.
Previously, intel-m10-bmc provided sysfs under
/sys/bus/spi/devices/... which is generalized in this change because
not all MAX10 BMC appear under SPI anymore.
Co-developed-by: Tianfei zhang <tianfei.zhang@intel.com>
Signed-off-by: Tianfei zhang <tianfei.zhang@intel.com>
Co-developed-by: Russ Weight <russell.h.weight@intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Co-developed-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230116100845.6153-11-ilpo.jarvinen@linux.intel.com
Split the common code from intel-m10-bmc driver into intel-m10-bmc-core
and move the SPI bus parts into an interface specific file.
intel-m10-bmc-core becomes the core MFD functions which can support
multiple bus interface like SPI bus.
Co-developed-by: Tianfei zhang <tianfei.zhang@intel.com>
Signed-off-by: Tianfei zhang <tianfei.zhang@intel.com>
Reviewed-by: Russ Weight <russell.h.weight@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> # hwmon
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230116100845.6153-5-ilpo.jarvinen@linux.intel.com
The Cerf, H3100, Badge4, Hackkit, LART, NanoEngine, PLEB, Shannon and
Simpad machines were all marked as unused as there are no known users
left. Remove all of these, along with references to them in defconfig
files and drivers.
Four machines remain now: Assabet, Collie (Zaurus SL5500), iPAQ H3600
and Jornada 720, each of which had one person still using them, with
Collie also being supported in Qemu.
Cc: Peter Chubb <peter.chubb@unsw.edu.au>
Cc: Stefan Eletzhofer <stefan.eletzhofer@eletztrick.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All board support that was marked as 'unused' earlier can
now be removed, leaving the five machines that that still
had someone using them in 2022, or that are supported in
qemu.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
As a minor optimization, this also lets us drop of_match_ptr(), as we
now know what it will resolve to, we might as well save cpp some work.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Lee Jones <lee@kernel.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Luca Ceresoli <luca.ceresoli@bootlin.com>
Cc: "Jonathan Neuschäfer" <j.neuschaefer@gmx.net>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221122154134.58a7a18b@endymion.delvare
The TPS65219 is a power management IC PMIC designed to supply a wide
range of SoCs in both portable and stationary applications. Any SoC can
control TPS65219 over a standard I2C interface.
It contains the following components:
- Regulators.
- Over Temperature warning and Shut down.
- GPIOs
- Multi Function Pins (MFP)
- power-button
This patch adds support for tps65219 PMIC. At this time only
the functionalities listed below are made available:
- Regulators probe and functionalities
- warm and cold reset support
- SW shutdown support
- Regulator warnings via IRQs
- Power-button via IRQ
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221104152311.1098603-5-jneanne@baylibre.com
The BD957x driver uses REGMAP_IRQ but does not 'select' to depend on
it. This can cause build failures. Select REGMAP_IRQ for BD957X.
Fixes: 0e9692607f ("mfd: bd9576: Add IRQ support")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/Y3SdCWkRr1L64SWK@dc75zzyyyyyyyyyyyyydt-3.rev.dnainternet.fi
Linus expressed a desire to have intel_soc_pmic_crc.o (INTEL_SOC_PMIC,
for Crystal Cove) be built on an "allmodconfig" build, when
I2C_DESIGNWARE_PLATFORM=m, to enhance build test coverage.
The PMIC driver won't work in this case since it requires
I2C_DESIGNWARE_PLATFORM=y to operate properly, but adding
"|| COMPILE_TEST" does improve the build test coverage.
Link: https://lore.kernel.org/all/CAHk-=wg=hh8xkPjiySnjAyR66AG64eyZ1Y9gHw+MCs8uuSZReA@mail.gmail.com/
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221101055433.16891-1-rdunlap@infradead.org
The HTC Herald machine was removed, so this driver is no
longer used anywhere.
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221019150410.3851944-17-arnd@kernel.org
The ASoC davinci voicecodec support is no longer used after
the removal of the dm3xx SoC platform, so the MFD driver is never
selected.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221019152947.3857217-11-arnd@kernel.org
The DaVinci DM355EVM platform is gone after the removal of all
unused board files, so the MTD device along with its sub-devices
can be removed as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221019152947.3857217-7-arnd@kernel.org
Adds Multi-function devices driver for SMpro co-processor found on the
Mt.Jade hardware reference platform with Ampere's Altra processor family.
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220929094321.770125-9-quan@os.amperecomputing.com
Add a specific MFD_SY7636A config option.
As part of this change we can use MFD_SY7636A as a dependency for all
SY7636a components and also remove the name from MFD_SIMPLE_MFD_I2C as
it no longer needs to be selectable.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220525115554.430971-2-alistair@alistair23.me
This adds support for the MediaTek MT6370 SubPMIC. MediaTek MT6370 is a
SubPMIC consisting of a single cell battery charger with ADC monitoring,
RGB LEDs, dual channel flashlight, WLED backlight driver, display bias
voltage supply, one general purpose LDO, and the USB Type-C & PD controller
complies with the latest USB Type-C and PD standards.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220805070610.3516-8-peterwu.pub@gmail.com
The driver depends on ACPI, ACPI_PTR() resolution is always the same.
Otherwise a compiler may produce a warning.
That said, the rule of thumb either ugly ifdeffery with ACPI_PTR or
none should be used in a driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220801114211.36267-7-andriy.shevchenko@linux.intel.com
The VSC7512 is a networking chip that contains several peripherals. Many of
these peripherals are currently supported by the VSC7513 and VSC7514 chips,
but those run on an internal CPU. The VSC7512 lacks this CPU, and must be
controlled externally.
Utilize the existing drivers by referencing the chip as an MFD. Add support
for the two MDIO buses, the internal phys, pinctrl, and serial GPIO.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220905162132.2943088-9-colin.foster@in-advantage.com
This driver is used by a specific range of SoCs between when the PRCM
hardware was introduced (A31) and when the PRCM CCU driver was added
(A83T). It is unlikely to be extended to additional hardware. Update
the description to include the full list of applicable SoCs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220702184044.51144-1-samuel@sholland.org
Instead of open coding p2sb_bar() functionality we are going to
use generic library. There is one more user en route.
This is more than just a clean-up. It also fixes a potential issue
seen when SPI BAR is 64-bit. The current code works if and only if
the PCI BAR of the hidden device is inside 4G address space. In case
when firmware decides to go above 4G, we will get a wrong address.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
This debugfs isn't used by anyone, if we want to dump the contents
of registers we should just convert the driver to regmap instead.
I'm also excluding this from the device tree bindings when converting
to YAML because it is not a real device, and device trees should
only contain real physical devices.
Delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220212214724.681530-1-linus.walleij@linaro.org
Add a simple driver for the Maxim MAX77714 PMIC, supporting RTC and
watchdog only.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a Kconfig name to the "Simple Multi-Functional Device support (I2C)"
device so that it can be enabled via menuconfig.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here is the set of changes for the driver core for 5.17-rc1.
Lots of little things here, including:
- kobj_type cleanups
- auxiliary_bus documentation updates
- auxiliary_device conversions for some drivers (relevant
subsystems all have provided acks for these)
- kernfs lock contention reduction for some workloads
- other tiny cleanups and changes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYd7deA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym8ngCgw0ANwrRPE5b1dthEmfU2f8Knk5kAn0pHQv6R
VRZJypgNfU/Pt0ykstZD
=CO9J
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of changes for the driver core for 5.17-rc1.
Lots of little things here, including:
- kobj_type cleanups
- auxiliary_bus documentation updates
- auxiliary_device conversions for some drivers (relevant subsystems
all have provided acks for these)
- kernfs lock contention reduction for some workloads
- other tiny cleanups and changes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (43 commits)
kobject documentation: remove default_attrs information
drivers/firmware: Add missing platform_device_put() in sysfb_create_simplefb
debugfs: lockdown: Allow reading debugfs files that are not world readable
driver core: Make bus notifiers in right order in really_probe()
driver core: Move driver_sysfs_remove() after driver_sysfs_add()
firmware: edd: remove empty default_attrs array
firmware: dmi-sysfs: use default_groups in kobj_type
qemu_fw_cfg: use default_groups in kobj_type
firmware: memmap: use default_groups in kobj_type
sh: sq: use default_groups in kobj_type
headers/uninline: Uninline single-use function: kobject_has_children()
devtmpfs: mount with noexec and nosuid
driver core: Simplify async probe test code by using ktime_ms_delta()
nilfs2: use default_groups in kobj_type
kobject: remove kset from struct kset_uevent_ops callbacks
driver core: make kobj_type constant.
driver core: platform: document registration-failure requirement
vdpa/mlx5: Use auxiliary_device driver data helpers
net/mlx5e: Use auxiliary_device driver data helpers
soundwire: intel: Use auxiliary_device driver data helpers
...
Intel Platform Monitoring Technology (PMT) support is indicated by presence
of an Intel defined PCIe Designated Vendor Specific Extended Capabilities
(DVSEC) structure with a PMT specific ID. The current MFD implementation
creates child devices for each PMT feature, currently telemetry, watcher,
and crashlog. However DVSEC structures may also be used by Intel to
indicate support for other features. The Out Of Band Management Services
Module (OOBMSM) uses DVSEC to enumerate several features, including PMT.
In order to support them it is necessary to modify the intel_pmt driver to
handle the creation of the child devices more generically. To that end,
modify the driver to create child devices for any VSEC/DVSEC features on
supported devices (indicated by PCI ID). Additionally, move the
implementation from MFD to the Auxiliary bus. VSEC/DVSEC features are
really multifunctional PCI devices, not platform devices as MFD was
designed for. Auxiliary bus gives more flexibility by allowing the
definition of custom structures that can be shared between associated
auxiliary devices and the parent device. Also, rename the driver from
intel_pmt to intel_vsec to better reflect the purpose.
This series also removes the current runtime pm support which was not
complete to begin with. None of the current devices require runtime pm.
However the support will be replaced when a device is added that requires
it.
Reviewed-by: Mark Gross <markgross@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20211208015015.891275-4-david.e.box@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The INTEL_SOC_PMIC_CHTDC_TI should be initialized early, before
loading the fbcon driver, as otherwise the i915 driver will
fail to configure pwm:
[ 13.674287] fb0: switching to inteldrmfb from EFI VGA
[ 13.682380] Console: switching to colour dummy device 80x25
[ 13.682468] i915 0000:00:02.0: vgaarb: deactivate vga console
[ 13.682686] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 13.685773] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 13.686219] i915 0000:00:02.0: [drm] *ERROR* Failed to configure the pwm chip
[ 13.699572] [drm] Initialized i915 1.6.0 20200313 for 0000:00:02.0 on minor 0
[ 13.739044] fbcon: i915drmfb (fb0) is primary device
[ 14.037792] intel_soc_pmic_exec_mipi_pmic_seq_element: No PMIC registered
...
[ 24.621403] intel_pmic_install_opregion_handler: Ask to register OpRegion for bus ID=PMI2, HID=INT33F5
[ 24.630540] intel_pmic_install_opregion_handler: OpRegion registered
(some extra debug printk's were added to the above)
As suggested by Hans, this patch also addresses an issue with
the dependencies, as, for this driver to be a bool, it also
need the I2C core and the I2C_DESIGNWARE driver to be builtin.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/86f546b3233fd799b0c39b83afc521440ebfe004.1638192232.git.mchehab+huawei@kernel.org
The only known BD70528 use-cases are such that the PMIC is controlled
from separate MCU which is not running Linux. I am not aware of
any Linux driver users. Furthermore, it seems there is no demand for
this IC. Let's ease the maintenance burden and drop the driver. We can
always add it back if there is sudden need for it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/cf7dfd98b3403ad363b2b48b57bdbfd57a6416cb.1637066805.git.matti.vaittinen@fi.rohmeurope.com
MFD_SIMPLE_MFD_I2C should select the MFD_CORE to a prevent build error:
aarch64-linux-ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_probe':
drivers/mfd/simple-mfd-i2c.c:55: undefined reference to `devm_mfd_add_devices'
Cc: <stable@vger.kernel.org>
Fixes: c753ea3178 ("mfd: simple-mfd-i2c: Add support for registering devices via MFD cells")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211102100420.112215-1-robert.marko@sartura.hr
The description mentioned AD5520, which is a different device.
Fixed the typo.
Signed-off-by: Ramona Alexandra Nechita <ramona.nechita@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The intel_pmt driver shows up as a compile option for all arches but is
32-bit and 64-bit x86 specific.
Add a CONFIG dependency on X86 for intel_pmt.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Add support for registering devices via MFD cells to Simple MFD (I2C)
- New Drivers
- Add support for Renesas Synchronization Management Unit (SMU)
- New Device Support
- Add support for N5010 to Intel M10 BMC
- Add support for Cannon Lake to Intel LPSS ACPI
- Add support for Samsung SSG{1,2} to ST-Ericsson's U8500 family
- Add support for TQMx110EB and TQMxE40x to TQ-Systems PLD TQMx86
- New Functionality
- Add support for GPIO to Intel LPC ICH
- Add support for Reset to Texas Instruments TPS65086
- Fix-ups
- Trivial, sorting, whitespace, renaming, etc; mt6360-core, db8500-prcmu-regs, tqmx86
- Device Tree fiddling; syscon, axp20x, qcom,pm8008, ti,tps65086, brcm,cru
- Use proper APIs for IRQ map resolution; ab8500-core, stmpe, tc3589x, wm8994-irq
- Pass 'supplied-from' property through axp288_fuel_gauge via swnode
- Remove unused file entry; MAINTAINERS
- Make interrupt line optional; tps65086
- Rename db8500-cpuidle driver symbol; db8500-prcmu
- Remove support for unused hardware; tqmx86
- Provide a standard LPC clock frequency for unknown boards; tqmx86
- Remove unused code; ti_am335x_tscadc
- Use of_iomap() instead of ioremap(); syscon
- Bug Fixes
- Clear GPIO IRQ resource flags when no IRQ is set; tqmx86
- Fix incorrect/misleading frequencies; db8500-prcmu
- Mitigate namespace clash with other GPIOBASE users
-----BEGIN PGP SIGNATURE-----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=7Zv8
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add support for registering devices via MFD cells to Simple MFD (I2C)
New Drivers:
- Add support for Renesas Synchronization Management Unit (SMU)
New Device Support:
- Add support for N5010 to Intel M10 BMC
- Add support for Cannon Lake to Intel LPSS ACPI
- Add support for Samsung SSG{1,2} to ST-Ericsson's U8500 family
- Add support for TQMx110EB and TQMxE40x to TQ-Systems PLD TQMx86
New Functionality:
- Add support for GPIO to Intel LPC ICH
- Add support for Reset to Texas Instruments TPS65086
Fix-ups:
- Trivial, sorting, whitespace, renaming, etc; mt6360-core, db8500-prcmu-regs, tqmx86
- Device Tree fiddling; syscon, axp20x, qcom,pm8008, ti,tps65086, brcm,cru
- Use proper APIs for IRQ map resolution; ab8500-core, stmpe, tc3589x, wm8994-irq
- Pass 'supplied-from' property through axp288_fuel_gauge via swnode
- Remove unused file entry; MAINTAINERS
- Make interrupt line optional; tps65086
- Rename db8500-cpuidle driver symbol; db8500-prcmu
- Remove support for unused hardware; tqmx86
- Provide a standard LPC clock frequency for unknown boards; tqmx86
- Remove unused code; ti_am335x_tscadc
- Use of_iomap() instead of ioremap(); syscon
Bug Fixes:
- Clear GPIO IRQ resource flags when no IRQ is set; tqmx86
- Fix incorrect/misleading frequencies; db8500-prcmu
- Mitigate namespace clash with other GPIOBASE users"
* tag 'mfd-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (31 commits)
mfd: lpc_sch: Rename GPIOBASE to prevent build error
mfd: syscon: Use of_iomap() instead of ioremap()
dt-bindings: mfd: Add Broadcom CRU
mfd: ti_am335x_tscadc: Delete superfluous error message
mfd: tqmx86: Assume 24MHz LPC clock for unknown boards
mfd: tqmx86: Add support for TQ-Systems DMI IDs
mfd: tqmx86: Add support for TQMx110EB and TQMxE40x
mfd: tqmx86: Fix typo in "platform"
mfd: tqmx86: Remove incorrect TQMx90UC board ID
mfd: tqmx86: Clear GPIO IRQ resource when no IRQ is set
mfd: simple-mfd-i2c: Add support for registering devices via MFD cells
mfd/cpuidle: ux500: Rename driver symbol
mfd: tps65086: Add cell entry for reset driver
mfd: tps65086: Make interrupt line optional
dt-bindings: mfd: Convert tps65086.txt to YAML
MAINTAINERS: Adjust ARM/NOMADIK/Ux500 ARCHITECTURES to file renaming
mfd: db8500-prcmu: Handle missing FW variant
mfd: db8500-prcmu: Rename register header
mfd: axp20x: Add supplied-from property to axp288_fuel_gauge cell
mfd: Don't use irq_create_mapping() to resolve a mapping
...
Add support for ClockMatrix(TM) and 82P33xxx families of timing
and synchronization devices. The access interface can be either
SPI or I2C. Currently, it will create 2 types of MFD devices,
which are to be used by the corresponding rsmu character device
driver and the PTP hardware clock driver, respectively.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver only covered one scenario in which ACPI devices with _HID
INT3472 are found, and its functionality has been taken over by the
intel-skl-int3472 module, so remove it.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Link: https://lore.kernel.org/r/20210603224007.120560-7-djrscally@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Samsung PMIC drivers since long time are used only on devicetree
platforms (Samsung Exynos) and there are no users with board files.
Drop the support for board files entirely and depend on OF for matching.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Qualcomm Technologies, Inc. PM8008 is a dedicated camera PMIC that
integrates all the necessary power management, housekeeping, and
interface support functions into a single IC. Its key features include
overtemperature protection, low-dropout linear regulators, GPIOs, and an
I2C interface.
Add an MFD driver to support it.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no reason why the arizona core,irq and codec model specific
regmap bits cannot be build as a module. All they do is export symbols
which are used by the arizona-spi/i2c and arizona-codec modules, which
themselves can be built as module.
Change the Kconfig and Makefile arizona bits so that the arizona MFD-core
can be built as a module.
This is especially useful on x86 platforms with a WM5102 codec, this
allows the arizona MFD driver necessary for the WM5102 codec to be
enabled in generic distro-kernels without growing the base kernel-image
size.
Note this also adds an explicit "depends on MFD_ARIZONA" to all the
arizona codec Kconfig options. The codec drivers use functions from mfd
arizona-core. These new depends are necessary to disallow the codec
drivers being builtin when the arizona-core is build as a module,
otherwise we end up with missing symbol errors when building vmlinuz.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
