8822c used to count OFDM FA count by subtracting tx count from FA count.
But it need to substract more counters to be accurate.
However, we can count it by adding up all of the FA counters we want.
And it is simpler to add than list all of the components to substract.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver Could fail to reset counter if rx clock gating is not disabled.
So we need to disable rx clock gating before resetting counters.
Otherwise counters may increase unexpected.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In 2G channels, the cck source and rxagc should be set to different
values based on different bandwidth to increase the performance of rx
sensitivity.
To improve rx throughput performance, the values of sbd subtune and
pt_opt should be changed in different bandwidth.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Collision of writing rf registers could occur if the driver writes
rf registers by direct write while the hardware is writing other rf
registers by pi write simultaneously.
Hardware pi write can be triggered by rf calibrations sometimes, so
the driver can not always write rf registers by direct write
protection. Direct write protection can make sure that there is no
hardware pi write during the direct write.
According to some experiments, if we add direct write protection
when switching channel, the performance of rf calibration will not
be affected.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add beacon function setting routines for each hardware port.
If beacon function is not enabled, the hardware is not able
to synchronize with AP's beacon and can miss the beacons
under some scenarios such as PS mode.
For AP and Adhoc modes that require to send beacons, do not
update the TSF, otherwise the beacon interval may be affected.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver uses random mac address to scan, the unicast probe response
will not be received because the addr1 is not matched. Configure port
address by requested mac address to receive probe response from AP.
To support random mac scan, we need to configure the mac address during
scan period to receive unicast prop_resp. After scan is completed,
configure the mac address back to the original one that the port used.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With dynamic power save support, rtw88 is able to support fast tx
path, claim it to mac80211.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. This driver was saving the debugfs file away to be
removed at a later time. However, the 80211 core would delete the whole
directory that the debugfs files are created in, after it asks the
driver to do the deletion, so just rely on the 80211 core to do all of
the cleanup for us, making us not need to keep a pointer to the dentries
around at all.
This cleans up the structure of the driver data a bit and makes the code
a tiny bit smaller.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. This driver was saving the debugfs file away to be
removed at a later time. However, the 80211 core would delete the whole
directory that the debugfs files are created in, after it asks the
driver to do the deletion, so just rely on the 80211 core to do all of
the cleanup for us, making us not need to keep a pointer to the dentries
around at all.
This cleans up the structure of the driver data a bit and makes the code
a tiny bit smaller.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WARN_ON triggers on older BCM4401-B0 100Base-TX ethernet controllers.
The warning serves no purpose. So let's just remove it.
Reported-by: H Buus <ubuntu@hbuus.com>
Signed-off-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable rtstatus is being initialized with a value that is never read
as rtstatus is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct ieee80211_regdomain {
...
struct ieee80211_reg_rule reg_rules[];
};
instance = kzalloc(sizeof(*mac->rd) +
sizeof(struct ieee80211_reg_rule) *
count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, reg_rules, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The assignment of 0 to variable k is never read once we break out of
the loop, so the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable badworden is assigned with a value that is never read and
it is re-assigned a new value immediately afterwards. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware can send invalid command response, the processing of
which can attempt to modify unexpected context and cause issues.
To fix this, driver should check that the command response ID is
same as the one it downloaded, and ignore processing of invalid
response.
Signed-off-by: Swati Kushwaha <swatiuma@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In set_mac_address, driver check for interfaces with same bss_type
For first STA entry, this would return 3 interfaces since all priv's have
bss_type as 0 due to kzalloc. Thus mac address gets changed for STA
unexpected. This patch adds check for first STA and avoids mac address
change. This patch also adds mac_address change for p2p based on bss_num
type.
Signed-off-by: Sharvari Harisangam <sharvari@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unadorned '%p' has restrictive policies these days, such that it usually
just prints garbage at early boot (see
Documentation/core-api/printk-formats.rst, "kernel will print
``(ptrval)`` until it gathers enough entropy"). Annotating with %pK
(for "kernel pointer") allows the kptr_restrict sysctl to control
printing policy better.
We might just as well drop this message entirely, but this fix was easy
enough for now.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This message is pointless.
While we're at it, include the error code in the error message, which is
not pointless.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The syzbot fuzzer found a bug in the p54 USB wireless driver. The
issue involves a race between disconnect and the firmware-loader
callback routine, and it has several aspects.
One big problem is that when the firmware can't be loaded, the
callback routine tries to unbind the driver from the USB _device_ (by
calling device_release_driver) instead of from the USB _interface_ to
which it is actually bound (by calling usb_driver_release_interface).
The race involves access to the private data structure. The driver's
disconnect handler waits for a completion that is signalled by the
firmware-loader callback routine. As soon as the completion is
signalled, you have to assume that the private data structure may have
been deallocated by the disconnect handler -- even if the firmware was
loaded without errors. However, the callback routine does access the
private data several times after that point.
Another problem is that, in order to ensure that the USB device
structure hasn't been freed when the callback routine runs, the driver
takes a reference to it. This isn't good enough any more, because now
that the callback routine calls usb_driver_release_interface, it has
to ensure that the interface structure hasn't been freed.
Finally, the driver takes an unnecessary reference to the USB device
structure in the probe function and drops the reference in the
disconnect handler. This extra reference doesn't accomplish anything,
because the USB core already guarantees that a device structure won't
be deallocated while a driver is still bound to any of its interfaces.
To fix these problems, this patch makes the following changes:
Call usb_driver_release_interface() rather than
device_release_driver().
Don't signal the completion until after the important
information has been copied out of the private data structure,
and don't refer to the private data at all thereafter.
Lock udev (the interface's parent) before unbinding the driver
instead of locking udev->parent.
During the firmware loading process, take a reference to the
USB interface instead of the USB device.
Don't take an unnecessary reference to the device during probe
(and then don't drop it during disconnect).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+200d4bb11b23d929335f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In b43_request_firmware(), when ieee80211_register_hw() fails,
b43_one_core_detach() is called. In b43_bcma_remove() and
b43_ssb_remove(), b43_one_core_detach() is called again. In this case,
null-pointer dereferences and double-free problems can occur when
the driver is removed.
To fix this bug, the call to b43_one_core_detach() in
b43_request_firmware() is deleted.
This bug is found by a runtime fuzzing tool named FIZZER written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is are two spelling mistakes in lbtf_deb_usb2 messages, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/btcoexist/rtl_btc.c: In function rtl_btc_btmpinfo_notify:
drivers/net/wireless/realtek/rtlwifi/btcoexist/rtl_btc.c:319:17: warning: variable len set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c: In function exhalbtc_connect_notify:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1581:16: warning: variable asso_type_v2 set but not used [-Wunused-but-set-variable]
'len' is never used since commit 6aad6075cc ("rtlwifi:
Add BT_MP_INFO to c2h handler.") so can be removed.
'asso_type_v2' is not used since introduction in
commit 0843e98a3b ("rtlwifi: btcoex: add assoc
type v2 to connection notify")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c: In function rtl8821ae_dm_check_rssi_monitor:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:658:6: warning: variable cur_txokcnt set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c: In function rtl8821ae_dm_check_edca_turbo:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:2657:7: warning: variable b_last_is_cur_rdl_state set but not used [-Wunused-but-set-variable]
They are never used so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed later.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The cckswing tables cckswing_table_ch1ch13 and cckswing_table_ch14 are
u8 array in little-endian order. To compare four u8 value with register
u32 value, cast the value to cpu order.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ofdm_index_old[] is the index of ofdmswing_table[], and used to indicate
initial value of ROFDM0_X{A,B}TXIQIMBALANCE in rtl8192de_phy_reg_2tarray[]
table, and the initial value is corresponding to calibration thermal value
written in efuse, namely rtlefuse->eeprom_thermalmeter. Then, local
variable ofdm_index_old[] save to rtlpriv->dm.ofdm_index[] for operational
use.
If thermal value (temperature) is increasing, output TX power is lower.
So, we calculate the delta between current and calibration thermal value,
then add power to yield expected and the same output TX power.
Thus, ofdm_index[] should be initialized as rtlpriv->dm.ofdm_index[], and
shift to proper index depends on delta of thermal value. Then, new power
value ofdmswing_table[ofdm_index[]] is written to register.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can reduce code size 264 bytes, and make code more readable.
text data bss dec hex filename
Before: 13586 0 16 13602 3522 rtl8192de/dm.o
After: 13322 0 16 13338 341a rtl8192de/dm.o
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit doesn't change logic at all. Since indentation is lower, the
wrapped statements can be put in single line that will become more
readable.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes an issue with wpa_supplicant dropping all scan
results because their where considered to be "too old" (e.g.:
"skip - scan result not recent enough (121056.086325 seconds too old)")
which is very weird because this looks like that the scan results have
been received before a scan started. This is due to the inaccuracy of
the default timing mechanism for calculating the BSS entry age.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes a crash that got introduced when the
mentioned patch replaced the direct list_head access
with skb_peek_tail(). When the device is starting up,
there are no entries in the queue, so previously to
"Use skb_peek_tail() instead..." the target_skb would
end up as the tail and head pointer which then could
be used by __skb_queue_after to fill the empty queue.
With skb_peek_tail() in its place will instead just
return NULL which then causes a crash in the
__skb_queue_after().
| BUG: unable to handle kernel NULL pointer dereference at 000000
| #PF error: [normal kernel read fault]
| PGD 0 P4D 0
| Oops: 0000 [#1] SMP PTI
| CPU: 0 PID: 12 Comm: kworker/0:1 Tainted: GO 5.1.0-rc7-wt+ #218
| Hardware name: MSI MS-7816/Z87-G43 (MS-7816), BIOS V1.11 05/09/2015
| Workqueue: events request_firmware_work_func
| RIP: 0010:p54_tx_pending+0x10f/0x1b0 [p54common]
| Code: 78 06 80 78 28 00 74 6d <48> 8b 07 49 89 7c 24 08 49 89 04 24 4
| RSP: 0018:ffffa81c81927d90 EFLAGS: 00010086
| RAX: ffff9bbaaf131048 RBX: 0000000000020670 RCX: 0000000000020264
| RDX: ffff9bbaa976d660 RSI: 0000000000000202 RDI: 0000000000000000
| RBP: ffff9bbaa976d620 R08: 00000000000006c0 R09: ffff9bbaa976d660
| R10: 0000000000000000 R11: ffffe8480dbc5900 R12: ffff9bbb45e87700
| R13: ffff9bbaa976d648 R14: ffff9bbaa976d674 R15: ffff9bbaaf131048
| FS: 0000000000000000(0000) GS:ffff9bbb5ec00000(0000) knlGS:00000
| CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
| CR2: 0000000000000000 CR3: 00000003695fc003 CR4: 00000000001606f0
| Call Trace:
| p54_download_eeprom+0xbe/0x120 [p54common]
| p54_read_eeprom+0x7f/0xc0 [p54common]
| p54u_load_firmware_cb+0xe0/0x160 [p54usb]
| request_firmware_work_func+0x42/0x80
| process_one_work+0x1f5/0x3f0
| worker_thread+0x28/0x3c0
Cc: stable@vger.kernel.org
Fixes: e3554197fc ("p54: Use skb_peek_tail() instead of direct head pointer accesses.")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function strcpy() is inherently not safe. Though the function
works without problems here, it would be better to use other safer
function, e.g. strlcpy(), to replace strcpy() still.
Signed-off-by: Neo Jou <neojou@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CONFIG_BRCMDBG selects WANT_DEV_COREDUMP but is only used by
brcmfmac so reflect that in the Kconfig.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The number of Kconfig items related to brcmfmac is considerable and
upcoming changes will add some more so it seems good idea to have
a separate Kconfig file for brcmfmac.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The LPS represents Leisure Power Save. When enabled, firmware will be in
charge of turning radio off between beacons. Also firmware should turn
on the radio when beacon is coming, and the data queued should be
transmitted in TBTT period.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dump warning messages when we get a q_mapping larger than the AC
numbers. And pick BE queue as default.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AC numbers are defined as enum in mac80211, use them instead of bare
0-3 indexing.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix sparse warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:6216:14:
warning: symbol 't4_get_tp_e2c_map' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
